Dynamic photonic perovskite light-emitting diodes with post-treatment-enhanced crystallization as writable and wipeable inscribers

Fabricating Planar Perovskite Solar Cells through a Greener Approach

High-quality perovskite thin films are typically produced via solvent engineering, which results in efficient perovskite solar cells (PSCs). Nevertheless, the use of hazardous solvents like precursor solvents (N-Methyl-2-pyrrolidone (NMP), dimethyl sulfoxide (DMSO), dimethylformamide (DMF), gamma-butyrolactone (GBL)) and antisolvents (chlorobenzene (CB), dibutyl ether (DEE), diethyl ether (Et2O), etc.) is crucial to the preparation of perovskite solutions and the control of perovskite thin film crystallization. The consumption of hazardous solvents poses an imminent threat to both the health of manufacturers and the environment. Consequently, before PSCs are commercialized, the current concerns about the toxicity of solvents must be addressed. In this study, we fabricated highly efficient planar PSCs using a novel, environmentally friendly method. Initially, we employed a greener solvent engineering approach that substituted the hazardous precursor solvents with an environmentally friendly solvent called triethyl phosphate (TEP). In the following stage, we fabricated perovskite thin films without the use of an antisolvent by employing a two-step procedure. Of all the greener techniques used to fabricate PSCs, the FTO/SnO2/MAFAPbI3/spiro-OMeTAD planar device configuration yielded the highest PCE of 20.98%. Therefore, this work addresses the toxicity of the solvents used in the perovskite film fabrication procedure and provides a promising universal method for producing PSCs with high efficiency. The aforementioned environmentally friendly approach might allow for PSC fabrication on an industrial scale in the future under sustainable conditions.

Thickness Optimization of Charge Transport Layers on Perovskite Solar Cells for Aerospace Applications

In aerospace applications, SiO_x deposition on perovskite solar cells makes them more stable. However, the reflectance of the light changes and the current density decreases can lower the efficiency of the solar cell. The thickness of the perovskite material, ETL, and HTL must be re-optimized, and testing the number of cases experimentally takes a long time and costs a lot of money. In this paper, an OPAL2 simulation was used to find the thickness and material of ETL and HTL that reduces the amount of light reflected by the perovskite material in a perovskite solar cell with a silicon oxide film. In our simulations, we used an air/SiO₂/AZO/transport layer/perovskite structure to find the ratio of incident light to the current density generated by the perovskite material and the thickness of the transport layer to maximize the current density. The results showed that when 7 nm of ZnS material was used for CH₃NH₃PbI₃-nanocrystalline perovskite material, a high ratio of 95.3% was achieved. In the case of CsFAPbIBr with a band gap of 1.70 eV, a high ratio of 94.89% was shown when ZnS was used.

Characterization of Large-Energy-Bandgap Methylammonium Lead Tribromide (MAPbBr3) Perovskite Solar Cells

We have investigated the effects of the methylammonium bromide (MABr) content of the precursor solution on the properties of wide-bandgap methylammonium lead tribromide (MAPbBr₃) perovskite solar cells (PSCs). In addition, the anti-solvent process for fabricating MAPbBr₃ perovskite thin films was optimized. The MAPbBr₃ precursor was prepared by dissolving MABr and lead bromide (PbBr₂) in N,N-dimethylformamide and N,N-dimethyl sulfoxide. Chlorobenzene (CB) was used as the anti-solvent. We found that both the morphology of the MAPbBr₃ layer and the PSCs performance are significantly affected by the MABr content in perovskite precursor solution and anti-solvent dripping time. The best-performing device was obtained when the molar ratio of MABr:PbBr₂ was 1:1 and the CB drip time was 10 s. The best device exhibited a power conversion efficiency of 7.58%, short-circuit current density of 7.32 mA·cm^-2, open-circuit voltage of 1.30 V, and fill factor of 79.87%.

A review of graphene derivative enhancers for perovskite solar cells

Due to the finite nature, health and environmental hazards currently associated with the use of fossil energy resources, there is a global drive to hasten the development and deployment of renewable energy technologies. One such area encompasses perovskite solar cells (PSCs) that have shown photoconversion efficiencies (PCE) comparable to silicon-based photovoltaics, but their commercialisation has been set back by short-term stability and toxicity issues, among others. A tremendous potential to overcome these drawbacks is presented by the emerging applications of graphene derivative-based materials in PSCs as substitutes or components, composites with other functional materials, and enhancers of charge transport, blocking action, exciton dissociation, substrate coverage, sensitisation and stabilisation. This review aims to illustrate how these highly capable carbon-based materials can advance PSCs by critically outlining and discussing their current applications and strategically identifying prospective research avenues. The reviewed works show that graphene derivatives have great potential in boosting the performance and stability of PSCs through morphological modifications and compositional engineering. This can drive the sustainability and commercial viability aspects of PSCs.