Mechanics of dynamic needle insertion into a biological material

A survey on puncture models and path planning algorithms of bevel-tipped flexible needles

Percutaneous needle insertion is a minimally invasive surgery with broad medical application prospects, such as biopsy and brachytherapy. However, the currently adopted rigid needles have limitations, as they cannot bypass obstacles or correct puncture deviations and can only travel along a straight path. Bevel-tip flexible needles are increasingly being adopted to address these issues, owing to their needle body's ease of deformation and bending. Successful puncture of flexible needles relies on accurate models and path planning, ensuring the needle reaches the target while avoiding vital tissues. This review investigates puncture models and path-planning algorithms by reviewing recent literature, focusing on the path-planning part. According to the literature, puncture models can be divided into three types: mechanical, finite element method (FEM), and kinematic models, while path-planning algorithms are categorized and discussed following the division used for mobile robots, which differs from the conventional approach for flexible needles-an innovation in this review. This review systematically summarizes the following categories: graph theory search, sampling-based, intelligent search, local obstacle avoidance, and other algorithms, including their implementation, advantages, and disadvantages, to further explore the potential to overcome obstacles in path planning for minimally invasive puncture needles. Finally, this study proposes future development trends in path-planning algorithms, providing possible directions for subsequent research for bevel-tipped flexible needles. This research aims to provide a resource for researchers to quickly learn about common path-planning algorithms, their backgrounds, and puncture models.

Assessment of needle-tissue force models based on ex vivo measurements

Needle insertion is one of the most common procedures in clinical practice. Existing statistics reveal that success rates of needle insertions can be low, leading to potential complications and patient discomfort. Real-time imaging techniques like ultrasound and X-ray can assist in improving precision, but even experienced practitioners may face challenges in visualizing the needle tip. Researchers have proposed models of force interactions during needle insertions into biological tissue to enhance accuracy. This article presents an evaluation of the forces acting on intravenous needles during insertion into skin. The aim was to explore mathematical models, compare them with data from tests on animal specimens, and select the most suitable model for future research. The experimental setup involved conducting needle insertion tests on animal-originated cadavers, using the Brucker Universal Mechanical Tester device, which measured the force response during vertical movement of the needle. The research was divided into 2 stages. In Stage I, force measurements were recorded for both the insertion and extraction phases of the hypodermic needles. The measurements were conducted for several different needle sizes, speed and insertion angles. In Stage II, five different models were examined to determine how well they matched the experimental data. Based on the analysis of fit quality coefficients, the Gordon's exponential model was identified as the best fit to the measured data. The influence of needle size, insertion angle, and insertion speed on the measured force values was confirmed. Different insertion speeds revealed the viscoelastic properties of the tested samples. The presence of the skin layer affected the puncture force and force values for subsequent layers.

A novel computational fracture toughness model for soft tissue in needle insertion

During the process of percutaneous puncture vascular intervention operation in endoscopic liver surgery, high precision needle manipulation requires the accurate needle tissue interaction model where the tissue fracture toughness is an important parameter to describe the tissue crack propagation, as well as to estimate tissue deformation and target displacement. However, the existing studies on fracture toughness estimation did not consider Young's modulus and the organ capsule structure. In this paper, a novel computational fracture toughness model is proposed considering insertion velocity, needle diameter and Young's modulus in insertion process, where the fracture toughness is determined by the tissue surface deformation, which was estimated through energy modeling using integrated shell element and three-dimensional solid element. The testbed is built to study the effect of different insertion velocities, needle diameters and Young's modulus on fracture toughness. The experiment result shows that the estimated result of computational fracture toughness model agrees well with the physical experimental data. In addition, the sensitivity analysis of different factors is conducted. Meanwhile, the model robustness analysis is investigated with different observation noises of Young's modulus and puncture displacement.

Honeybee stinger-based biopsy needle and influence of the barbs on needle forces during insertion/extraction into the iliac crest: A multilayer finite element approach

Bone marrow biopsy (BMB) needles are frequently used in medical procedures, including extracting biological tissue to identify specific lesions or abnormalities discovered during a medical examination or a radiological scan. The forces applied by the needle during the cutting operation significantly impact the sample quality. Excessive needle insertion force and possible deflection might cause tissue damage, compromising the integrity of the biopsy specimen. The present study aims at proposing a revolutionary bioinspired needle design that will be utilized during the BMB procedure. A non-linear finite element method (FEM) has been used to analyze the insertion/extraction mechanisms of the honeybee-inspired biopsy needle with barbs into/from the human skin-bone domain (i.e., iliac crest model). It can be seen from the results of the FEM analysis that stresses are concentrated around the bioinspired biopsy needle tip and barbs during the needle insertion process. Also, these needles reduce the insertion force and reduce the tip deflection. The insertion force in the current study has been reduced by 8.6% for bone tissue and 22.66% for skin tissue layers. Similarly, the extraction force has been reduced by an average of 57.54%. Additionally, it has been observed that the needle-tip deflection got reduced from 10.44 mm for a plain bevel needle to 6.3 mm for a barbed biopsy bevel needle. According to the research findings, the proposed bioinspired barbed biopsy needle design could be utilized to create and produce novel biopsy needles for successful and minimally invasive piercing operations.

Bioinspired medical needles: a review of the scientific literature

Needles are commonly used in medical procedures. However, current needle designs have some disadvantages. Therefore, a new generation of hypodermic needles and microneedle patches drawing inspiration from mechanisms found in nature (i.e. bioinspiration) is being developed. In this systematic review, 80 articles were retrieved from Scopus, Web of Science, and PubMed and classified based on the strategies for needle-tissue interaction and propulsion of the needle. The needle-tissue interaction was modified to reduce grip for smooth needle insertion or enlarge grip to resist needle retraction. The reduction of grip can be achieved passively through form modification and actively through translation and rotation of the needle. To enlarge grip, interlocking with the tissue, sucking the tissue, and adhering to the tissue were identified as strategies. Needle propelling was modified to ensure stable needle insertion, either through external (i.e. applied to the prepuncturing movement of the needle) or internal (i.e. applied to the postpuncturing movement of the needle) strategies. External strategies include free-hand and guided needle insertion, while friction manipulation of the tissue was found to be an internal strategy. Most needles appear to be using friction reduction strategies and are inserted using a free-hand technique. Furthermore, most needle designs were inspired by insects, specifically parasitoid wasps, honeybees, and mosquitoes. The presented overview and description of the different bioinspired interaction and propulsion strategies provide insight into the current state of bioinspired needles and offer opportunities for medical instrument designers to create a new generation of bioinspired needles.

Puncturing of soft tissues: experimental and fracture mechanics-based study

The integrity of soft materials against puncturing is of great relevance for their performance because of the high sensitivity to local rupture caused by rigid sharp objects. In this work, the mechanics of puncturing is studied with respect to a sharp-tipped rigid needle with a circular cross section, penetrating a soft target solid. The failure mode associated with puncturing is identified as a mode-I crack propagation, which is analytically described by a two-dimensional model of the target solid, taking place in a plane normal to the penetration axis. It is shown that the force required for the onset of needle penetration is dependent on two energy contributions, that are, the strain energy stored in the target solid and the energy consumed in crack propagation. More specifically, the force is found to be dependent on the fracture toughness of the material, its stiffness and the sharpness of the penetrating tool. The reference case within the framework of small strain elasticity is first investigated, leading to closed-form toughness parameters related to classical linear elastic fracture mechanics. Then, nonlinear finite element analyses for an Ogden hyperelastic material are presented. Supporting the proposed theoretical framework, a series of puncturing experiments on two commercial silicones is presented. The combined experimental-theoretical findings suggest a simple, yet reliable tool to easily handle and assess safety against puncturing of soft materials.

Optimizing autoinjector devices using physics-based simulations and Gaussian processes

Autoinjectors are becoming a primary drug delivery option to the subcutaneous space. These devices need to work robustly and autonomously to maximize drug bio-availability. However, current designs ignore the coupling between autoinjector dynamics and tissue biomechanics. Here we present a Bayesian framework for optimization of autoinjector devices that can account for the coupled autoinjector-tissue biomechanics and uncertainty in tissue mechanical behavior. The framework relies on replacing the high fidelity model of tissue insertion with a Gaussian process (GP). The GP model is accurate yet computationally affordable, enabling a thorough sensitivity analysis that identified tissue properties, which are not part of the autoinjector design space, as important variables for the injection process. Higher fracture toughness decreases the crack depth, while tissue shear modulus has the opposite effect. The sensitivity analysis also shows that drug viscosity and spring force, which are part of the design space, affect the location and timing of drug delivery. Low viscosity could lead to premature delivery, but can be prevented with smaller spring forces, while higher viscosity could prevent premature delivery while demanding larger spring forces and increasing the time of injection. Increasing the spring force guarantees penetration to the desired depth, but it can result in undesirably high accelerations. The Bayesian optimization framework tackles the challenge of designing devices with performance metrics coupled to uncertain tissue properties. This work is important for the design of other medical devices for which optimization in the presence of material behavior uncertainty is needed.

Experimental and simulation investigation of surgical needle insertion into soft tissue mimic biomaterial for minimally invasive surgery (MIS)

The surgical needle insertion process is widely applied in medical interference. During the insertion process, the inhomogeneity and denseness of the soft tissues make it tough to detect the essential tissue damage, a rupture occurs that contains huge forces and material deformations. This study is very important, as all the above-mentioned factors are very significant for modern invasive surgery so that the success rate of the surgery can increase and the patient recovers smoothly. This investigation intends to perform minimally invasive surgical (MIS) procedures and reduce the living tissue damage while performing the biopsy, PCNL, etc. A fracture mechanics method was analyzed to create a needle insertion model which can estimate the needle insertion force during inset in tissue-like PVA gel. The force model was calculated by needle insertion experimentally, and also estimated the needle tip geometry, and diameter influences the fracture toughness. Validate exp. results with simulation results and other papers. It is observed that needle diameter has a significant effect on fracture toughness, whereas the insertion velocity has a slight impact on the fracture toughness. During the rotational needle insertion process, the winds-up of the gel occurs and the diameter of the hole was increasing with increased rpm. Maximum insertion force was noticed in the 27 G needle at 5 mm/s. The interaction function will be less at the maximum fracture development region.

Experimental study of mosquito-inspired needle to minimize insertion force and tissue deformation

The aim of this work is to propose a mosquito-inspired (bioinspired) design of a surgical needle that can decrease the insertion force and the tissue deformation, which are the main causes of target inaccuracy during percutaneous procedures. The bioinspired needle was developed by mimicking the geometrical shapes of mosquito proboscis. Needle prototypes were manufactured and tested to determine optimized needle shapes and geometries. Needle insertion tests on a tissue-mimicking polyvinylchloride (PVC) gel were then performed to emulate the mosquito-proboscis stinging dynamics by applying vibration and insertion velocity during the insertion. An insertion test setup equipped with a sensing system was constructed to measure the insertion force and to assess the deformation of the tissue. It was discovered that using the proposed bioinspired design, the needle insertion force was decreased by 60% and the tissue deformation was reduced by 48%. This finding is significant for improving needle-based medical procedures.

Modeling and Analysis of Prostate Soft Tissue Puncture Performance using Puncture Needle

When treating prostate cancer, the use of puncture robots is an effective method to perform radioactive seed implantation surgery. However, when the puncture needle enters the lesion, the soft tissue is easily deformed owing to the complex force between the puncture needle and soft tissue, which leads to a puncture deviation between the needle tip and target point. To solve this problem effectively, the prostate soft tissue puncture process is studied based on the analysis of the puncture needle–soft tissue interaction. First, the puncture force is classified into contact, friction, and cutting forces by a quantitative decomposition method, and the corresponding force model is established. Based on the theoretical analysis of the model, it is deduced that these factors can affect the deformation created by puncturing the soft tissue. Subsequently, a puncture platform is built and many biomimetic soft tissue models are established. Multiple puncture experiments on the influencing factors are conducted using the method of controlling a single variable. Using the spatial puncture deviation as the test metrics, the significance of the influencing factors of the puncture deformation is verified. Finally, it can be concluded from the experimental analysis that the main factor that affects the puncture deviation is the puncture speed, whereas the puncture depth has no significant influence. The puncture speed was optimized and verified by experiments, and the results showed that a stable puncture accuracy under different puncture depths can be obtained by selecting an optimized puncture speed (12.6 mm/s). This work provides a design reference to study the positioning accuracy of minimally invasive puncture surgery.

Study of the surgical needle and biological soft tissue interaction phenomenon during insertion process for medical application: A Survey

The insertion of the surgical needle in soft tissue has involved significant interest in the current time because of its purpose in minimally invasive surgery (MIS) and percutaneous events like biopsies, PCNL, and brachytherapy. This study represents a review of the existing condition of investigation on insertion of a surgical needle in biological living soft tissue material. As observes the issue from numerous phases, like, analysis of the cutting forces modeling (insertion), tissue material deformation, analysis of the needle deflection for the period of the needle insertion, and the robot-controlled insertion procedures. All analysis confirms that the total needle insertion force is the total of dissimilar forces spread sideways the shaft of the insertion needle for example cutting force, stiffness force, and frictional force. Various investigations have analyzed all these kinds of forces during the needle insertion process. The force data in several measures are applied for recognizing the biological tissue materials as the needle is penetrated or for path planning. The deflection of the needle during insertion and tissue material deformation is the main trouble for defined needle placing and efforts have been prepared to model them. Applying existing models numerous insertion methods are established that are discussed in this review.

On-demand anchoring of wireless soft miniature robots on soft surfaces

Anchoring soft millirobots on surfaces, such as biological tissues, is essential to perform long-duration medical functions robustly on a target position. For robust anchoring, we propose a wireless mechanism that can be precisely controlled by remote heating to achieve on-demand needle release and mechanical interlocking. Such a mechanism can be easily integrated on existing untethered soft robots, allowing them to anchor robustly to soft surfaces while retaining their locomotion capabilities. Furthermore, we demonstrate advanced functionalities of such robots, such as controlled surface detachment and subsurface drug delivery into three-dimensional cancer spheroids. Given these capabilities, the proposed mechanism can serve as a platform for the development of soft robots with a new suite of biomedical capabilities.

Untethered soft miniature robots capable of accessing hard-to-reach regions can enable new, disruptive, and minimally invasive medical procedures. However, once the control input is removed, these robots easily move from their target location because of the dynamic motion of body tissues or fluids, thereby restricting their use in many long-term medical applications. To overcome this, we propose a wireless spring-preloaded barbed needle release mechanism, which can provide up to 1.6 N of force to drive a barbed needle into soft tissues to allow robust on-demand anchoring on three-dimensional (3D) surfaces. The mechanism is wirelessly triggered using radio-frequency remote heating and can be easily integrated into existing untethered soft robotic platforms without sacrificing their mobility. Design guidelines aimed at maximizing anchoring over the range of the most biological tissues (kPa range) and extending the operating depth of the device inside the body (up to 75%) are also presented. Enabled by these advances, we achieve robust anchoring on a variety of ex vivo tissues and demonstrate the usage of such a device when integrated with existing soft robotic platforms and medical imaging. Moreover, by simply changing the needle, we demonstrate additional functionalities such as controlled detachment and subsurface drug delivery into 3D cancer spheroids. Given these capabilities, our proposed mechanism could enable the development of a new class of biomedical-related functionalities, such as local drug delivery, disease monitoring, and hyperthermia for future untethered soft medical robots.

Cone cracks in tissue-mimicking hydrogels during hypodermic needle insertion: the role of water content

Needle insertion into soft biological tissues is a common process in various surgical procedures. During insertion, soft biological tissues with different water contents undergo large deformation often leading to uncontrollable cracks and tissue damage. Despite the numerous experimental studies and numerical modelling of needle-tissue interaction, the results do not show any consistency mainly due to the heterogeneity of tissue properties and opaqueness. In this context, understanding the fracture behaviour of soft tissues during needle insertion is important for minimally invasive surgeries and other medical procedures. Recently, we showed that the needle insertion into a transparent, tissue-mimicking polyacrylamide (PAAm) hydrogel causes periodic cone cracks. In this work, we systematically varied the water content of the PAAm hydrogel in the preparation state and performed needle insertion experiments using a hypodermic needle at a constant velocity to study the fracture characteristics of the PAAm hydrogel. The results show that the number of peaks, the magnitudes of the insertion forces, and corresponding cone cracks decrease with increasing water content. Furthermore, we discussed the influence of water on cone crack fracture characteristics, cone angle, periodicity, crack speed and fracture energy release rate. These results provide a better understanding of the fracture processes of soft tissues with different water concentrations such as the lung, liver, and brain during needle insertion and the control of tissue damage during needle insertion involved in medical procedures.

Monitored needle acceleration in endoscopic ultrasound-guided fine-needle aspiration of solid pancreatic masses improves sample quality and diagnostic accuracy: a randomized trial

BACKGROUND : Endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) is recommended for the diagnosis of solid pancreatic masses. We aimed to evaluate whether a high needle movement acceleration value during puncture increases diagnostic accuracy. METHODS : EUS-FNA needle acceleration was measured using a PocketLab accelerometer connected by Bluetooth to a smartphone. Two passes (fast and slow, with higher and lower than 1g [9.8 m/s²] needle acceleration values, respectively) were performed in a random order. The sample cellularity and quality were measured using semiquantitative scales. RESULTS : 51 patients were included (32 women; mean age 63). The mean (standard deviation [SD]) acceleration values were 1.59g (0.66g) for the fast pass and 0.32g (0.19g) for the slow pass (P < 0.001). The fast pass yielded significantly higher levels of EUS-FNA accuracy (84.3 % vs. 68.6 %; P = 0.02) and adequate quality scores (94.1 % vs. 76.5 %; P = 0.007). High cellularity scores were seen with similar frequencies (15.7 % vs. 11.8 %; P = 0.32). CONCLUSIONS : A higher than 1g EUS-FNA needle acceleration may increase the diagnostic accuracy and specimen quality from solid pancreatic lesions.

Bioinspired Rotation Microneedles for Accurate Transdermal Positioning and Ultraminimal-Invasive Biomarker Detection with Mechanical Robustness

Microneedle permits transdermal biosensing and drug delivery with minor pain. However, accurate microneedle transdermal positioning with minimal skin deformation remains a significant technical challenge due to inhomogeneous skin topology and discontinuous force applied to the microneedle. Here, we introduce bioinspired rotation microneedles for in vivo accurate microneedle positioning as inspired by honeybees’ stingers. We demonstrate the benefits of rotation microneedles in alleviating skin resistance through finite element analysis, full-thickness porcine validations, and mathematical derivations of microneedle-skin interaction stress fields. The max penetration force was mitigated by up to 45.7% and the force attenuation rate increased to 2.73 times in the holding stage after penetration. A decrease in max skin deflection and a faster deformation recovery introduced by rotation microneedles implied a more precise penetration depth. Furthermore, we applied the rotation microneedles in psoriasis mice, a monogenic disorder animal model, for minimally invasive biological sample extraction and proinflammatory cytokine monitoring. An ultrasensitive detection method is realized by using only one microneedle to achieve cytokine mRNA level determination compared to commonly required biopsies or blood collection. Thus, rotation microneedles permit a simple, rapid, and ultraminimal-invasive method for subcutaneous trace biological sample acquisition and subsequent point-of-care diagnostics with minimal damage to both microneedles and skins.

A computational multilayer model to simulate hollow needle insertion into biological porcine liver tissue

Modelling of needle insertion in soft tissue has developed significant interest in recent years due to its application in robot-assisted minimally invasive surgeries such as biopsies and brachytherapy. However, this type of surgery requires real-time feedback and processing which complex computational models may not be able to provide. In contrast to the existing mechanics-based kinetic models, a simple multilayer tissue model using a Coupled Eulerian Lagrangian based Finite Element method has been developed using the dynamic principle. The model simulates the needle motion for flexible hollow bevel-angled needle (15° and 30°, 22 Gauge) insertion into porcine liver tissue, which includes material parameters obtained from unconfined compression testing of porcine liver tissue. To validate simulation results, needle insertion force and cutting force within porcine liver tissue were compared with corresponding experimental results obtained from a custom-built needle insertion system. For the 15° and 30° bevel-angle needles, the percentage error for cutting force (mean) of each needle compared to computational model, were 18.7% and 11.9% respectively. Varying the needle bevel angle from 30° to 15° results in an increase of the cutting force, but insertion force does not vary among the tested bevel angles. The validation of this computationally efficient multilayer Finite Element model can help engineers to better understand the biomechanical behaviour of medical needle inside soft biological tissue. Ultimately, this multilayer approach can help advance state-of-art clinical applications such as robot-assisted surgery that requires real-time feedback and processing. STATEMENT OF SIGNIFICANCE: The significance of the work is in confirming the effectiveness of multilayer material based finite element (FE) method to model biopsy needle insertion into soft biological porcine liver tissue. A multilayer Coupled Eulerian Lagrangian (CEL) based FE modelling technique allowed testing of heterogeneous, non-linear viscoelastic porcine liver tissue in a system, so direct comparison of needle tissue interaction forces on the intrinsic material (tissue) behaviour could be made. To the best of the authors' knowledge, the present research investigates for the first time modelling of a three dimensional (3D) hollow needle insertion using a multilayer stiffness model of biological tissue using FE based CEL method and presents a comparison of simulation results with experimental data.

Experimental study on needle insertion force to minimize tissue deformation in tongue tissue

This study reports on the effects of insertion velocity, needle tip geometry and needle diameter on tissue deformation and maximum insertion force. Moreover, the effect of multiple insertions with the same needle on the maximum insertion force is reported. The tissue deformation and maximum insertion force strongly depend on the insertion velocity and the tip geometry. No correlation was found between the outer diameter and the maximum insertion force for small needles (30G - 32G). The endurance experiments showed no remarkable difference in the maximum insertion force during 100 insertions.

Feasibility of extracting tissue material properties via cohesive elements: a finite element approach to probe insertion procedures in non-invasive spine surgeries

Modeling the mechanical behavior of soft tissue probe insertion remains a challenging endeavor due to involved interdependent phenomena comprising tissue nonlinear deformation, contact between the probe and the tissue, crack propagation, and viscoelastic effects. To that matter, cohesive elements allow simulating crack formation and propagation, which provides a promising path to modeling the mechanical behavior of probe insertion in soft tissues. As such, the aim of the present study was to investigate the feasibility of devising and integrating an algorithm in a finite element (FE) case study in efforts of reverse engineering the material properties of non-homogeneous soft tissues. A layered nonlinear tissue model with a cohesive zone was created in the commercial software ABAQUS. Material properties were iteratively modified via a hybrid gradient descent optimization algorithm: minimizing the resultant error to first find optimum Ogden's hyperelastic parameters, followed by obtaining the damage parameters. Perceived material properties were then compared to those obtained via experimental human cadaver testing. Under the investigated four-layered muscle model, numerical results overlapped, to a great extent, with six different force-insertion experimental profiles with an average error of [Formula: see text] 15%. The best profile fit was realized when the highest sudden force drop was less than 60% of the peak force. Lastly, the FE analysis revealed an increase in stiffness as the probe advanced inside the tissue. The optimization algorithm demonstrated its capability to reverse engineer the material parameters required for the FE analysis of real, non-homogeneous, soft tissues. The significance of this procedure lies within its ability to extract tissue material parameters, in real time, with little to no intervention or invasive experimental tests. This could potentially further serve as a database for different muscle layers and force-insertion profiles, used for surgeon and physician clinical training purposes.

The effect of skin tension, needle diameter and insertion velocity on the fracture properties of porcine tissue

Using metal needles to penetrate skin tissue is common in medical treatments for the delivery of medication or minimally invasive surgery. In most applications the fracture properties of skin tissue is not important as the human surgeon has full control over the needle. Given that robotically controlled surgeries and self applied medical devices have become increasingly popular, a better understanding of the fracture properties and how to mathematically model the fracture process is needed. Experiments measuring the force required to fracture porcine skin tissue were done while varying the applied skin tension, needle insertion speed and needle diameter. The applied skin tension was found to have the greatest influence on the fracture properties, while the insertion speed was found to have a negligible impact. The variance in experimental results was not well explained by the three independent variables alone, suggesting that additional parameters influence the fracture process.

A novel multi-DoF surgical robotic system for brachytherapy on liver tumor: Design and control

Purpose

Radioactive seed implantation is an effective invasive treatment method for malignant liver tumors in hepatocellular carcinomas. However, challenges of the manual procedure may degrade the efficacy of the technique, such as the high accuracy requirement and radiation exposure to the surgeons. This paper aims to develop a robotic system and its control methods for assisting surgeons on the treatment.

Method

We present an interventional robotic system, which consists of a 5 Degree-of-Freedom (DoF) positioning robotic arm (a 3-DoF translational joint and a 2-DoF revolute joint) and a needle actuator used for needle insertion and radioactive seeds implantation. Control strategy is designed for the system to ensure the safety of the motion. In the designed framework, an artificial potential field (APF)-based motion planning and an ultrasound (US) image-based contacting methods are proposed for the control.

Result

Experiments were performed to evaluate position and orientation accuracy as well as validate the motion planning procedure of the system. The mean and standard deviation of targeting error is 0.69 mm and 0.33 mm, respectively. Needle placement accuracy is 1.10 mm by mean. The feasibility of the control strategy, including path planning and the contacting methods, is demonstrated by simulation and experiments based on an abdominal phantom.

Conclusion

This paper presents a robotic system with force and US image feedback in assisting surgeons performing brachytherapy on liver tumors. The proposed robotic system is capable of executing an accurate needle insertion task with by optical tracking. The proposed methods improve the safety of the robot’s motion and automate the process of US probe contacting under the feedback of US-image.

Needle insertion-induced quasiperiodic cone cracks in hydrogel

Needle insertion, a standard process for various minimally invasive surgeries, results in tissue damage which sometimes leads to catastrophic outcomes. Opaqueness and inhomogeneity of the tissues make it difficult to observe the underlying damage mechanisms. In this paper, we use transparent and homogeneous polyacrylamide hydrogel as a tissue mimic to investigate the damages caused during needle insertion. The insertion force shows multiple events, characterised by a gradual increase in the force followed by a sharp fall. Synchronised recording of the needle displacement into the gel shows that each event corresponds to propagation of stable cone crack. Though sporadic uncontrolled cracking has been discussed earlier, this is the first report of nearly periodic, stable and well-controlled 3-D cone cracks inside the hydrogel during deep penetration. We show that the stress field around the needle tip is responsible for the symmetry and periodicity of the cone cracks. These results provide a better understanding of the fracture processes in soft and brittle materials and open a promising perspective in needle designs and the control of tissue damages during surgical operations.

Needle insertion forces and fluid injection pressures during targeting of nerves in a soft embalmed cadaver model

PURPOSE

Forceful needle-nerve contact and high subepineural pressures and are recognised causes of nerve damage. Pressure and force measurements are necessary to inform the mechanisms of nerve injury, build virtual simulator environments and provide operator feedback during simulation training. However, the range of pressures and forces encountered at tissue layers during targeted needle insertion and fluid injection are not known.

METHODS

We built a needle that recorded in-line pressure during fluid injection and continuously measured force at the needle tip. Two anaesthetists were randomised to insert a 21 g block needle at 48 nerve sites on both sides of 3 soft embalmed Thiel cadavers. Our objective was to measure pressure and force during the course of targeted nerve injection at epimysium, in perineural tissue, on epineurium and during subepineural injection. At each interface, we infused a 0.5 ml bolus of embalming solution at a rate of 12 ml min^-1 and recorded the pressure response. Force was measured continuously in the background throughout the procedure.

RESULTS

Pressure was greater at epineurium and within subepineurium than perineural tissue, geometric ratio (95% CI) 4.7 (3.0-7.3) kPa and 3.8 (2.5-5.7) kPa, respectively, both P < 0.0001. Force on nerve contact and on nerve penetration was greater than force in perineural tissue, geometric ratios (95% CI) 3.0 (1.9-4.7) N and 3.6 (2.2-7.5) N, respectively, both P < 0.0001. On nerve contact, 1 in 6 insertions were ≥ 5 N CONCLUSIONS: Despite valid infusion pressures, anaesthetists exerted excessive force on nerves.

Variation of the Penetration Effort in an Artificial Tissue by Hypodermic Needles

Fear of injection-related pain is a drawback to injectable therapy. Hypodermic injections are a cause for great anxiety and reduced adherence to the subcutaneous application of insulin for glycemic control in diabetics or in the treatment of multiple sclerosis, increasing the risk of complications and mortality. Injured or sick people have to undergo several daily injections, forcing them to rotate the veins and regions used to recover from the trauma caused by the perforation of the skin, tissue, muscles, veins, and arteries. People who suffer from type 1 diabetes mellitus (DM1) need to have their glycemic control 3 to 5 times a day and to take insulin up to 3 times a day. In both cases, the patient needs to perforate the skin. To quantify the pain perceived by the patients depends on the evaluation of each patient and therefore is subjective. This study aims to understand the application and self-application of hypodermic injections and decrease pain during its application and the phobia of the patient, following the reasoning that the lower the effort to penetrate the needle, the less trauma in the tissue and therefore the pain provoked. For that, it was analyzed how some of the characteristics of the needle can influence the sensation of pain in the injection. The needle penetration effort was measured in an artificial tissue (substitute skin model) for different cannula diameters, roughness, depth of penetration, lubrication, and angles of the perforating tip bevel. This study aimed to find alternatives to facilitate the application and self-application of hypodermic injections, increase safety and comfort, and reduce the pain intensity perceived by the patient. To do this, the bevel of needles used repeatedly was analyzed in the profile projector and SEM to verify the loss of the profile or the formation of burrs that could hamper the penetration or traumatize the tissue during the reuse of needles. It has also been mechanically analyzed, which can be done to prevent that the needles used in the subcutaneous application do not inadvertently reach the muscle. The greater penetration effort observed in the needles with greater angle of the bevel is responsible for the patient's perception of pain.

Vinpocetine loaded ultradeformable liposomes as fast dissolving microneedle patch: Tackling treatment challenges of dementia

Vinpocetine (VPN) displays poor bioavailability (~7%) and short half-life (2-3 h) justifying the frequent dosing requirement of currently marketed oral tablets (thrice daily) and thus, posing a great challenge to patient compliance. Present work envisaged to achieve an infusion like delivery through transdermal route so as to tackle aforesaid challenges. With this aim, ultradeformable liposomes (UDL) incorporated fast dissolving microneedle patch (MNP) of VPN was developed and optimized for vesicle size and percent drug entrapment (critical quality attributes, CQA) utilizing the quality by design tool. Fractional factorial design followed by combined D-optimal design were applied to identify critical material attributes and obtain their statistically verified optimum levels (Phospholipon 90G, 15.17 mM; Phospholipon 90H, 4.83 mM; sodium deoxycholate, 15 mol% and Vinpocetine, 5 mol%) showing mean vesicle size of 75.65 nm and mean drug entrapment of 87.44%. An insignificant change in CQA of optimized UDL after incorporation in MNP further represented their physical compatibility with MNP components. In vitro characterization of these microneedles revealed rapid dissolution (~2 min) and good skin penetrability with around 0.684 N axial needle fracture force (ANFF). The safety was ascertained in vitro by exposing HaCaT cells to VPN UDL MNP components. A 94.27% cell viability advocated the safe nature of excipients used in formulation. Ex vivo permeation across full thickness pig ear skin revealed a steady state flux of 11.091 μg/cm²/h via VPN UDL MNP with around 9-fold enhancement when compared to flux value achieved through VPN suspension. In vivo pharmacokinetic and pharmacodynamic study in Sprague Dawley rats showed a 3-fold rise in relative bioavailability and a comparable mean escape latency via UDL MNP as compared to its oral suspension. In addition, half-life of 14 h and MRT of 21 h further confirmed the controlled release behavior of UDL MNP for prolonged period of time. In nutshell, the developed fast dissolving microneedle patch of VPN showed promising results with the prospect of lowering dose as well as dosing frequency for improved patient compliance.

Ice coating -A new method of brain device insertion to mitigate acute injuries

BACKGROUND

Reduction of insertion injury is likely important to approach physiological conditions in the vicinity of implanted devices intended to interface with the surrounding brain.

NEW METHODS

We have developed a novel, low-friction coating around frozen, gelatin embedded needles. By introducing a layer of thawing ice onto the gelatin, decreasing surface friction, we mitigate damage caused by the implantation.

RESULTS AND COMPARISON WITH EXISTING METHODS

The acute effects of a transient stab on neuronal density and glial reactions were assessed 1 and 7 days post stab in rat cortex and striatum both within and outside the insertion track using immunohistochemical staining. The addition of a coat of melting ice to the frozen gelatin embedded needles reduced the insertion force with around 50 %, substantially reduced the loss neurons (i.e. reduced neuronal void), and yielded near normal levels of astrocytes within the insertion track 1 day after insertion, as compared to gelatin coated probes of the same temperature without ice coating. There were negligible effects on glial reactions and neuronal density immediately outside the insertion track of both ice coated and cold gelatin embedded needles. This new method of implantation presents a considerable improvement compared to existing modes of device insertion.

CONCLUSIONS

Acute brain injuries following insertion of e.g. ultra-flexible electrodes, can be reduced by providing an outer coat of ultra-slippery thawing ice. No adverse effect of lowered implant temperature was found, opening the possibility of locking fragile electrode construct configurations in frozen gelatin, prior to implantation into the brain.

Bevel angle study of flexible hollow needle insertion into biological mimetic soft-gel: Simulation and experimental validation

BACKGROUND

A thorough understanding of cutting-edge geometry and cutting forces of hollow biopsy needles are required to optimise needle tip design to improve fine needle aspiration procedures.

OBJECTIVES

To incorporate the dynamics of needle motion in a model for flexible hollow bevel tipped needle insertion into a biological mimetic soft-gel using parameters obtained from experimental work. Additionally, the models will be verified against corresponding needle insertion experiments.

METHODS

To verify simulation results, needle deflection and insertion forces were compared with corresponding experimental results acquired with an in-house developed needle insertion mechanical system. Additionally, contact stress distribution on needles from agar gel for various time scales were also studied.

RESULTS

For the 15°, 30°, 45°, 60° bevel angle needles, and 90° blunt needle, the percentage error in needle deflection of each needle compared to experiments, were 7.3%, 9.9%, 8.6%, 7.8%, and 9.7% respectively. Varying the bevel angle at the needle tip demonstrates that the needle with a lower bevel angle produces the largest deflection, although the insertion force does not vary too much among the tested bevel angles.

CONCLUSION

This experimentally verified computer-based simulation model could be used as an alternative tool for better understanding the needle-tissue interaction to optimise needle tip design towards improved biopsy efficiency.

Analysis of Surgical Forces Required to Gain Access Using a Probe for Minimally Invasive Spine Surgery via Cadaveric-Based Experiments Towards Use in Training Simulators

INTRODUCTION

Virtual Reality haptic-based surgical simulators for training purposes have recently been receiving increased traction within the medical field. However, its future adoption is contingent on the accuracy and reliability of the haptic feedback.

GOAL

This study describes and analyzes the implementation of a set of haptic-tailored experiments to extract the force feedback of a medical probe used in minimally invasive spinal lumbar interbody fusion surgeries.

METHODS

Experiments to extract linear, lateral and rotational insertion, relaxation and extraction of the tool within the spinal muscles, intervertebral discs and lumbar nerve on two cadaveric torsos were conducted.

RESULTS

Notably, mean force-displacement and torque-angular displacement curves describing the different tool-tissue responses were reported with a maximum force of 6.87 (±1.79) N at 40 mm in the muscle and an initial rupture force through the Annulus Fibrosis of 20.550 (±7.841) N at 6.441 mm in the L₄/L₅ disc.

CONCLUSION

The analysis showed that increasing the velocity of the probe slightly reduced and delayed depth of the muscle punctures but significantly lowered the force reduction due to relaxation. Decreasing probe depth resulted with a reduction to the force relaxation drop. However, varying the puncturing angle of attack resulted with a significant effect on increasing force intensities. Finally, not resecting the thoracolumbar fascia prior to puncturing the muscle resulted with a significant increase in the force intensities.

SIGNIFICANCE

These results present a complete characterization of the input required for probe access for spinal surgeries to provide an accurate haptic response in training simulators.

Effect of vibration on insertion force and deflection of bioinspired needle in tissues

The design of surgical needles used in biopsy procedures have remained fairly standard despite the increase in complexity of surgeries. Higher needle insertion forces and deflection can increase tissue damage and decrease biopsy sample integrity. To overcome these drawbacks, we present a novel bioinspired approach to reduce insertion forces and minimize needle-tip deflection. It is well known from the literature, design of bioinspired surgical needles results in decreasing insertion forces and needle-tip deflection from the needle insertion path. This technical note studies the influence of vibration on bioinspired needle to further reduce insertion forces and needle-tip deflection. Bioinspired needle geometrical parameters such as barb shapes and geometries were analyzed to determine the best design parameters. Static and dynamic (vibration) needle insertion tests were performed to determine the maximum insertion forces and to estimate needle-tip deflection. Our results show that introducing vibration on the bioinspired needle insertion can reduce the maximum insertion force by up to 50%. It was also found that the needle-tip deflection is decreased by 47%.

Development and Characterization of a Benchtop Corneal Puncture Injury Model

During recent military operations, eye-related injuries have risen in frequency due to increased use of explosive weaponry which often result in corneal puncture injuries. These have one of the poorest visual outcomes for wounded soldiers, often resulting in blindness due to the large variations in injury shape, size, and severity. As a result, improved therapeutics are needed which can stabilize the injury site and promote wound healing. Unfortunately, current corneal puncture injury models are not capable of producing irregularly shaped, large, high-speed injuries as seen on the battlefield, making relevant therapeutic development challenging. Here, we present a benchtop corneal puncture injury model for use with enucleated eyes that utilizes a high-speed solenoid device suitable for creating military-relevant injuries. We first established system baselines and ocular performance metrics, standardizing the different aspects of the benchtop model to ensure consistent results and properly account for tissue variability. The benchtop model was evaluated with corneal puncture injury objects up to 4.2 mm in diameter which generated intraocular pressure levels exceeding 1500 mmHg. Overall, the created benchtop model provides an initial platform for better characterizing corneal puncture injuries as seen in a military relevant clinical setting and a realistic approach for assessing potential therapeutics.

Influence of needling conditions on the corneal insertion force

Needle insertion plays an important part in the process of corneal graft surgery. In this paper, a three-dimensional symmetry model of the human cornea is constructed using the finite element method. Simplification of specific optic physiology is defined for the model: The cornea constrained by the sclera is presented as two layers consisting of epithelium and stroma. A failure criterion based on the distortion energy theory has been proposed to predict the insertion process of the needle. The simulation results show a good agreement with the experimental data reported in the literature. The influence of needling conditions (e.g. insertion velocity, rotation parameters and vibration parameters) on the insertion force are then discussed. In addition, a multi-objective optimization based on particle swarm optimization (PSO) is applied to reduce the insertion force. The numerical results provide guidelines for selecting the motion parameters of the needle and a potential basis for further developments in robot-assisted surgery.

Guidelines for designing a realistic peripheral venous catheter insertion simulator: A literature review

A literature review was conducted to develop more realistic medical simulators that better prepare aspiring health professionals to perform a medical procedure in vivo. Thus, this review proposes an approach that might assist researchers design improved medical simulators, particularly new materials that would enhance the sensation of touch for skin substitutes. By targeting the current needs in the field of simulation learning, we concluded that peripheral venous catheter insertion simulators lack realistic haptic feedback. Enhanced peripheral venous catheter insertion simulators will accelerate the mastery of the medical procedure, thus decreasing the number of failures in patients and costs related to this procedure.

Simulation of biopsy bevel-tipped needle insertion into soft-gel

Planning and practice of surgical procedures can be improved through the use of modelling. This study provides an insight into the biopsy needle (i.e. hollow cannula) and needle-tissue interactions using a modelling approach, thus enabling the optimization of needle-tip designs not only for training but also for the planning of surgical procedures. Simulations of needle insertion into agar gel were performed using a Coupled Eulerian-Lagrangian (CEL) based finite element (FE) analysis, adapted for large deformation and tissue fracture. The experimental work covers needle insertion into 3% agar gel using a needle with a beveled tip of various angles, to assess the validity of the simulation. The simulated needle deflection and insertion force for two needles (i.e. Needle 1 with 18° bevel angle and Needle 2 with 27° bevel angle) were compared with corresponding experimental results. The contact stress (i.e. contact pressure) on the needles from the agar gel during the insertion of the needles were also studied. Observations indicate that varying the needle bevel angle from 27° to 18° results in a decrease of the peak force (i.e. puncture force) and an increase in needle deflection. Quantitatively, the percentage errors between the experimental data and the FE model for the total insertion force along the z-direction (i.e. Z Force) for Needle 1 and 2 were 4% and 4.8% (p > 0.05), respectively. Similarly, needle deflection percentage errors along the x-z plane were 5.7% and 10% respectively. Therefore, the forces and needle deflection values predicted by the simulation are a close approximation of the experimental model, validating the Coupled Eulerian-Lagrangian based FE model. Thus, providing an experimentally validated model for biopsy and cytology needle design in silico that has the potential to replace the current build and break approach of needle design used by manufacturers.

Phenomenological tissue fracture modeling for an Endoscopic Sinus and Skull Base Surgery training system based on experimental data

The ideal simulator for Endoscopic Sinus and Skull Base Surgery (ESSS) training must be supported by a physical model and provide repetitive behavior in a controlled environment. Development of realistic tissue models is a key part of ESSS virtual reality (VR)-based surgical simulation. Considerable research has been conducted to address haptic or force feedback and propose a phenomenological tissue fracture model for sino-nasal tissue during surgical tool indentation. Mechanical properties of specific sino-nasal regions of the sheep head have been studied in various indentation and relaxation experiments. Tool insertion at different indentation rates into coronal orbital floor (COF) tissue is modeled as a sequence of three events: deformation, fracture, and cutting. The behavior in the deformation phase can be characterized using a non-linear, rate-dependent modified Kelvin-Voigt model. A non-linear model for tissue behavior prior to the fracture point is presented. The overall model shows a non-positive dependency of maximum force on tool indentation rate, which indicates faster tool insertion velocity decreases the maximum final fracture force. The tissue cutting phase has been modeled to characterize the force necessary to slice through the COF. The proposed model in this study can help develop VR-based ESSS base simulators in otolaryngology and ophthalmology surgeries. Such simulators are useful in preoperative planning, accurate surgical simulation, intelligent robotic assistance, and treatment applications.

A simple insertion technique to reduce the bending of thinbevel-point needles

Objective: Needle insertion is a common component of most diagnostic and therapeutic interventions. Needles with asymmetrically sharpened points such as the bevel point are ubiquitous. Their insertion path is typically curved due to the rudder effect at the point. However, the common planned path is straight, leading to targeting errors. We present a simple technique that may substantially reduce these errors. The method was inspired by practical experience, conceived mathematically, and refined experimentally. Methods: Targeting errors are reduced by flipping the bevel on the opposite side (rotating the needle 180° about its axis), at a certain depth during insertion. The ratio of the flip depth to the full depth of insertion is defined as the flip depth ratio (FDR). Based on a model, FDR is constant 0.3. Results: Experimentally, the ratio depends on the needle diameter, 0.35 for 20Ga and 0.45 for 18Ga needles. Thinner needles should be flipped a little shallower, but never less than 0.3. Conclusion: Practically, a physician may expect to reduce ∼80% of needle deflection errors by simply flipping the needle. The technique may be used by hand or with guidance devices.

Using Simulation to Help Specify Design Parameters for Vacuum-Assisted Needle Biopsy Systems

Needle biopsy is a routine medical procedure for examining tissue or biofluids for the presence of disease using standard methods of pathology. The finite element analysis (FEA) methodology can provide guidance for optimizing the geometric parameters. The needle biopsy is simulated and analyzed while varying the needle angle, the aperture size and the slice-push ratio k. The results indicate that tissue reaction force in the axial direction of needle gradually decreases, and the stress and strain are more concentrated at the tip of needle with the increases of tip angle; the tissue reaction force decreases, and the torque increases while the slice-push ratio increases; and higher slice–push ratio can increase the peak stress concentration on the cutting edge and deformation of tissue; in the process of core needle cutting, increasing slice–push ratio can reduce the tissue reaction force significantly. While the aperture on distal wall of outer cannula becomes wider, the tissue reaction force increases significantly, and the cutting process will be more unstable. The results have the potential to provide important insight for improving the needle biopsy design process.

Design of a Handheld Trocar Insertion Device for Laparoscopic Surgery to Avoid Overshooting

Overshooting trocar insertion in Iaparoscopic surgery has been extensively cited as a major cause of surgical injury. The complexity and extensive insertion force required of the current handheld insertion method increases the risk of overshooting and is difficult for novice and female operators. Hence, we developed a trocar insertion device to make the procedure easier and safer. The device is designed so it is easy to handle and assemble. It used negative pressure and pneumatic cylinders to lift the abdominal wall and two motors to drive the trocar insertion. In addition, we interpreted the characteristics of the insertion force and developed an algorithm to detect whether the trocar is properly inserted. By monitoring changes in the insertion force with this device, the trocar insertion can be stopped automatically and immediately. The development of this device has realized the automation of trocar insertion. It reduces the demand on operators and improves the safety of the procedure.

Demonstration of Subretinal Injection Using Common-Path Swept Source OCT Guided Microinjector

In this paper, we present the development of a handheld common-path swept source optical coherence tomography (CP-SSOCT) guided microinjector system and demonstrated its utility by precisely injecting fluorescein dye in the subretinal layer of ex vivo bovine eyes. The system enables precise subretinal injection with micron-level injection depth control. This was achieved by using a high-resolution CP-SSOCT distal sensor and signal processing using a graphics-processing unit (GPU), which made a real-time smart motion control algorithm possible. The microinjector performance was first evaluated using a gelatin phantom in terms of its ability for dynamic depth targeting and injection depth. This is followed by using an ex vivo bovine eye model to perform multiple consecutive subretinal injections of fluorescein dye. The results validated the OCT guided injector’s ability to precisely guide and lock in the needle tip to the target depth during injection. The ex vivo evaluation tests demonstrate that an OCT-guided injector can consistently guide the injecting needle to the desired depth and is able to maintain the position with 9.38 μm average root mean square error during the injections.

The Role of Impulse, Tissue Stretching, and Tip Geometry for Tissue Penetration of Polymer Needles

Polymer needles for medical injections offer a range of opportunities like compatibility with magnetic resonance scanning and simultaneous delivery of more than one drug. However, the lower stiffness property of polymers compared to steel is a challenge for penetration. This paper explores strategies for higher penetration success, which include impulse insertion, tissue stretching, and different tip geometries. The strategies are experimentally examined using three layers of nitrile rubber gloves and sticking glue to create an artificial skin model. It is demonstrated that polymer needles have higher penetration rates when the strategies are applied. Penetration rates were only 10–20% when using slow speed insertion (0.2 mm/s) but 100% penetration rates was achieved using impulse insertion. Penetration forces are similar for slow insertion speed and high speed (impulse insertion) and for needles made out of different material (polymer or steel). Conical and pyramidal tips were studied for polymer needles and a commercial bevel steel needle tip. The result was lower penetration forces and 100% penetration success was possible using the pyramidal polymer needles. For the model in study was observed a similar behavior (penetration force and rate of penetration success) for steel and polymer pyramidal needles. An analysis of variance statistical analysis show significance when using springs and strain, as well for the combination of both.

Mechanics of anesthetic needle penetration into human sciatic nerve

Nerve blocks are frequently performed by anesthesiologists to control pain. For sciatic nerve blocks, the optimal placement of the needle tip between its paraneural sheath and epineurial covering is challenging, even under ultrasound guidance, and frequently results in nerve puncture. We performed needle penetration tests on cadaveric isolated paraneural sheath (IPS), isolated nerve (IN), and the nerve with overlying paraneural sheath (NPS), and quantified puncture force requirement and fracture toughness of these specimens to assess their role in determining the clinical risk of nerve puncture. We found that puncture force (123 ± 17 mN) and fracture toughness (45.48 ± 9.72 J m^-2) of IPS was significantly lower than those for NPS (1440 ± 161 mN and 1317.46 ± 212.45 Jm^-2, respectively), suggesting that it is not possible to push the tip of the block needle through the paraneural sheath only, without pushing it into the nerve directly, when the sheath is lying directly over the nerve. Results of this study provide a physical basis for tangential placement of the needle as the ideal situation for local anesthetic deposition, as it allows for the penetration of the sheath along the edge of the nerve without entering the epineurium.

FORCE CHARACTERISTICS AND EFFECTIVE STOPPING UPON THE ABDOMINAL WALL IS PENETRATED OUT BY TROCAR DURING LAPAROSCOPIC SURGERY

Overshooting during trocar insertion may injury patient viscera and arteries or even lead to death. It has been extensively cited as a kind of common medical negligence. Hence, this paper investigated the force characteristics during a trocar inserted into the abdominal wall and developed strategies for effective stopping upon the trocar penetrated out of the abdominal wall. First, an experimental platform with two degrees of freedom was assembled. Second, two insertion methods were compared and the insertion forces using three types of trocars were measured respectively. Subsequently, we interpreted the force characteristics in terms of insertion principle and the abdominal structure. And based on the force characteristics, we generated two algorithms for the two insertion methods, which can be utilized to stop inserting effectively upon the trocar penetrated out of the abdominal wall. Finally, we evaluated the merits and demerits of the two algorithms. This paper proposed the interpretation of force characteristics during trocar insertion and achieved effective stopping to avoid overshooting. It provides foundations for the development of automatic trocar insertion device in the future.

Novel design of honeybee-inspired needles for percutaneous procedure

The focus of this paper is to present new designs of innovative bioinspired needles to be used during percutaneous procedures. Insect stingers have been known to easily penetrate soft tissues. Bioinspired needles mimicking the barbs in a honeybee stinger were developed for a smaller insertion force, which can provide a less invasive procedure. Decreasing the insertion force will decrease the tissue deformation, which is essential for more accurate targeting. In this study, some design parameters, in particular, barb shape and geometry (i.e. front angle, back angle, and height) were defined, and their effects on the insertion force were investigated. Three-dimensional printing technology was used to manufacture bioinspired needles. A specially-designed insertion test setup using tissue mimicking polyvinyl chloride (PVC) gels was developed to measure the insertion and extraction forces. The barb design parameters were then experimentally modified through detailed experimental procedures to further reduce the insertion force. Different scales of the barbed needles were designed and used to explore the size-scale effect on the insertion force. To further investigate the efficacy of the proposed needle design in real surgeries, preliminary ex vivo insertion tests into bovine liver tissue were performed. Our results show that the insertion force of the needles in different scales decreased by 21-35% in PVC gel insertion tests, and by 46% in bovine liver tissue insertion tests.

Force Modeling, Identification, and Feedback Control of Robot-Assisted Needle Insertion: A Survey of the Literature

Robot-assisted surgery is of growing interest in the surgical and engineering communities. The use of robots allows surgery to be performed with precision using smaller instruments and incisions, resulting in shorter healing times. However, using current technology, an operator cannot directly feel the operation because the surgeon-instrument and instrument-tissue interaction force feedbacks are lost during needle insertion. Advancements in force feedback and control not only help reduce tissue deformation and needle deflection but also provide the surgeon with better control over the surgical instruments. The goal of this review is to summarize the key components surrounding the force feedback and control during robot-assisted needle insertion. The literature search was conducted during the middle months of 2017 using mainstream academic search engines with a combination of keywords relevant to the field. In total, 166 articles with valuable contents were analyzed and grouped into five related topics. This survey systemically summarizes the state-of-the-art force control technologies for robot-assisted needle insertion, such as force modeling, measurement, the factors that influence the interaction force, parameter identification, and force control algorithms. All studies show force control is still at its initial stage. The influence factors, needle deflection or planning remain open for investigation in future.