Preparation of Copper-Based Catalysts for Obtaining Methanol by the Chemical Impregnation Method

This paper presents the preparation of heterogeneous catalysts for the direct hydrogenation process of CO2 to methanol. The development of the modern chemical industry is inextricably linked to the use of catalytic processes. As a result, currently over 80% of new technologies introduced in the chemical industry incorporate catalytic processes. Since the basic factor of catalytic processes is the catalysts, the studies for the deepening of the knowledge regarding the nature of the action of the catalysts, for the development of new catalysts and catalytic systems, as well as for their improvement, represent a research priority of a fundamental or applied nature. The Cu/ZnO/Al2O3 catalyst for the synthesis of green methanol, using precursors of an inorganic (copper nitrate, denoted by Cu/ZnO/Al2O3-1) and organic (copper acetate, denoted by Cu/ZnO/Al2O3-2) nature, are obtained by chemical impregnation that includes two stages: preparation and one of calcination. The preparation methods and conditions, as well as the physico-chemical properties of the catalyst precursor, play a major role in the behavior of the catalysts. The prepared catalysts were characterized using atomic adsorption analysis, scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis, specific surface area and pore size analyses, adsorption, and the chemisorption of vapor (BET).

NASICON Membrane with High Ionic Conductivity Synthesized by High-Temperature Solid-State Reaction

In the present work, we studied the impact of excess Na addition on the structure of the standard NASICON ion conductor along with Na ion transport mechanisms. In this sense, NASICON ceramic membranes (NZSP) were prepared by a simple chemical synthesis method, the solid state reaction (SSR), using an excess of 5% Na (Na3.15Zr2Si2PO12) and an excess of 10% Na (Na3.3Zr2Si2PO12), in order to improve the conduction properties of the ceramic membrane. The characterization of the NZSP nanoparticles was performed by measuring the particle size by dynamic light scattering (DLS), the morphology of the NASICON samples pre-sintered at 1100 °C was analyzed by the SEM method (scanning electron microscope), and X-ray diffraction (XRD) analysis was used to investigate the crystal structure of samples, while the surface area was measured using the BET technique. The electrical properties (i.e., ionic conductivity) were evaluated by impedance spectroscopic methods at room temperature (RT). Following the experiments for NASICON membranes without Na excess, with 5% Na excess, and with 10% Na excess synthesized at different pressing forces and sintering temperatures, it was found that membranes with a 10% Na excess, sintered at 1175 °C for 10 h, presented a good ionic conductivity (4.72 × 10-4 S/cm).

Platinum-Functionalized Graphene Oxide: One-Pot Synthesis and Application as an Electrocatalyst

This paper presents the preparation of platinum on a reduced graphene oxide matrix (PtrGO) using the microwave-assisted method with three different pH solutions. The platinum concentration determined by energy-dispersive X-ray analysis (EDX) was 4.32 (weight%), 2.16 (weight %) and 5.70 (weight%), corresponding to pH 3.3, 11.7 and 7.2, respectively. Pt functionalization of reduced graphene oxide (rGO) decreased the rGO specific surface, as shown by Brunauer, Emmett and Teller (BET) analysis. An XRD spectrum of platinum-decorated reduced graphene oxide (rGO) showed the presence of the associated phases of rGO and centered cubic platinum peaks. An oxygen reduction reaction (ORR) electrochemical characterization performed using the rotating disk electrode (RDE) method showed that in PtGO1 synthetized in an acidic environment, with 4.32 Pt (weight%) determined by EDX, platinum is much more dispersed, which explains its better electrochemical oxygen reduction reaction performance. Koutecky-Levich (K-L) plots calculated at different potentials prove a good linear relationship. Electron transfer numbers (n) determined from the K-L plots are between 3.1 and 3.8, which confirms that the ORR for all the samples can be regarded as first-order reaction kinetics of O₂ concentration formed on the Pt surface during ORR.

Noble Metals Functionalized on Graphene Oxide Obtained by Different Methods-New Catalytic Materials

In recent years, research has focused on developing materials exhibiting outstanding mechanical, electrical, thermal, catalytic, magnetic and optical properties such as graphene/polymer, graphene/metal nanoparticles and graphene/ceramic nanocomposites. Two-dimensional sp² hybridized graphene has become a material of choice in research due to the excellent properties it displays electrically, thermally, optically and mechanically. Noble nanomaterials also present special physical and chemical properties and, therefore, they provide model building blocks in modifying nanoscale structures for various applications, ranging from nanomedicine to catalysis and optics. The introduction of noble metal nanoparticles (NPs) (Au, Ag and Pd) into chemically derived graphene is important in opening new avenues for both materials in different fields where they can provide hybrid materials with exceptional performance due to the synergistical result of the specific properties of each of the materials. This review presents the different synthetic procedures for preparing Pt, Ag, Pd and Au NP/graphene oxide (GO) and reduced graphene oxide (rGO) composites.