One-step hydrothermal synthesis of CuS/MoS2 composite for use as an electrochemical non-enzymatic glucose sensor

Early diagnosis may be crucial for the prevention of chronic diabetes mellitus. For that herein, we prepared a CuS/MoS2 composite for a non-enzymatic glucose sensor through a one-step hydrothermal method owing to the synergetic effect of CuS/MoS2. The surface morphology of CuS/MoS2 was studied by Field Emission Scanning Electron Microscopy (FESEM) and Cs-corrected Scanning Transmission Electron Microscopy (Cs-STEM). The crystallinity and surface composition of CuS/MoS2 were analyzed by X-ray Diffraction (XRD) and X-ray Photoelectron Spectroscopy (XPS) respectively. The working electrode was prepared from CuS/MoS2 electrocatalyst, and for that dispersed solution of electrocatalyst was used to fabricate the material-loaded glassy carbon electrode (GC). CuS/MoS2 composite shows the viability of electrocatalyst to oxidize glucose in an alkaline solution with sensitivity and detection limit of 252.71 μA mM-1 cm-2 and 1.52 μM respectively. The proposed glucose sensor showed reasonable stability and potential selectivity during electrochemical analysis. Accordingly, the CuS/MoS2 composite has potential as a viable material for glucose sensing in diluted human serum.

Nanoarchitectonics of Three-Dimensional Carbon Nanofiber-Supported Hollow Copper Sulfide Spheres for Asymmetric Supercapacitor Applications

Three-dimensional carbon nanofiber (3D-CNF)-supported hollow copper sulfide (HCuS) spheres were synthesized by the facile hydrothermal method. The morphology of the as-synthesized HCuS@3D-CNF composite clearly revealed that the 3D-CNFs act as a basement for HCuS spheres. The electrochemical performance of as-synthesized HCuS@3D-CNFs was evaluated by cyclic voltammetry (CV) tests, gravimetric charge-discharge (GCD) tests, and Nyquist plots. The obtained results revealed that the HCuS@3D-CNFs exhibited greater areal capacitance (4.6 F/cm²) compared to bare HCuS (0.64 F/cm²) at a current density of 2 mA/cm². Furthermore, HCuS@3D-CNFs retained excellent cyclic stability of 83.2% after 5000 cycles. The assembled asymmetric device (HCuS@3D-CNFs//BAC) exhibits an energy density of 0.15 mWh/cm² with a working potential window of 1.5 V in KOH electrolyte. The obtained results demonstrate that HZnS@3D-CNF nanoarchitectonics is a potential electrode material for supercapacitor applications.

Chitosan polymer matrix-derived nanocomposite (CuS/NSC) for non-enzymatic electrochemical glucose sensor

In this study, N and S co-doped chitosan polymer matrix-derived composite (CuS/NSC) was synthesized via a one-step hydrothermal technique using a low-cost copper complex of chitosan polymer. Cyclic voltammetry and chronoamperometry revealed excellent electrocatalytic performance. The glucose sensor exhibited a linear range of 160 μM to 11.76 mM, a low detection limit 2.72 μM and a sensitivity of 13.62 mA mM^-1 cm^-2 with an excellent linear response. Furthermore, the sensor also displayed selectivity for glucose over potential interfering agents and exhibited a satisfactory recovery percentage using real sample in human serum. The results demonstrate that, CuS/NSC is an efficient nanocomposite material for non-enzymatic glucose sensors and is applicable for glucose detection in biological fluids.

Synthesis of three-dimensional mesoporous Cu–Al layered double hydroxide/g-C3N4 nanocomposites on Ni-foam for enhanced supercapacitors with excellent long-term cycling stability

In this study, a novel composite of Cu–Al layered double hydroxide (LDH) nanosheets and g-C₃N₄-covered Ni-foam was fabricated via a simple and facile two-step process.

Electrospinning Directly Synthesized Porous TiO2 Nanofibers Modified by Graphitic Carbon Nitride Sheets for Enhanced Photocatalytic Degradation Activity under Solar Light Irradiation

We report a direct approach to the fabrication of a composite made of porous TiO2 nanofibers (NFs) and graphitic carbon nitride (g-C3N4) sheets, by means of an angled two-nozzle electrospinning combined with calcination process. Different wt % amounts of g-C3N4 particles in a polymer solution from one nozzle and TiO2 precursors containing the same polymer solution from another nozzle were electrospun and deposited on the collector. Structural characterizations confirm a well-defined morphology of the TiO2/g-C3N4 composite in which the TiO2 NFs are uniformly attached on the g-C3N4 sheet. This proper attachment of TiO2 NFs on the g-C3N4 sheets occurred during calcination. The prepared composites showed the enhanced photocatalytic activity over the photodegradation of rhodamine B and reactive black 5 under natural sunlight. Here, the synergistic effect between the g-C3N4 sheets and the TiO2 NFs having anisotropic properties enhanced the photogenerated electron-hole pair separation and migration, which was confirmed by the measurement of photoluminescence spectra, cyclic voltammograms, and electrochemical impedance spectra. The direct synthesis approach that is established here for such kinds of sheetlike structure and porous NFs composites could provide new insights for the design of high-performance energy conversion catalysts.

Synthesis, characterization, organic compound degradation activity and antimicrobial performance of g-C3N4 sheets customized with metal nanoparticles-decorated TiO2 nanofibers

Here, we discuss for the first time a simple and direct approach to fabricate multifunctional silver nanoparticles decorated porous TiO₂ nanofibers interpolated on a thin and large g-C₃N₄ sheet using a electrospinning–calcination process.