Effects of Ga on the structural, mechanical and electronic properties of β-Ti-45Nb alloy by experiments and ab initio calculations

This work aims to investigate the structural, mechanical and electronic properties of four novel β-type (100-x)(Ti-45Nb)-xGa alloys (x = 2, 4, 6, 8 wt%) for implant applications by means of experimental and theoretical (ab initio) methods. All alloys retain the bcc β phase in the solution-treated and quenched state while the lattice parameter decreases with increase in Ga content. This is due to its smaller atomic radius compared to Ti and Nb, in line with the present density functional theory (DFT) calculations. Tensile and microhardness tests indicate a clear strengthening effect with increasing Ga content, with yield strengths in the range 551 ÷ 681 MPa and microhardness in the range 174 ÷ 232 HV_0.1, mainly attributed to grain refinement and solid solution strengthening. Ga also positively affects ductility, with a maximum value of tensile strain at fracture of 32%. Non-destructive ultrasonic measurements and DFT calculations reveal that the bulk modulus is unaffected by the Ga presence. This phenomenon might be due to the fact that Ga introduced bonding and anti-bonding electron low energy states which balance the average bond strength among the atoms in the metallic matrix. Nevertheless, the introduction of new Ga-Ti super sp-like bonding orbitals along the [110] and [-110] directions in the Ga neighborhood could explain the increase of the Young's modulus upon Ga addition (73 ÷ 82.5 GPa) that was found experimentally in the present work. Hence, Ga addition to Ti-45Nb leads to a suitable balance between increased strength and low Young's modulus.

Scintillation light detection in the 6-m drift-length ProtoDUNE Dual Phase liquid argon TPC

DUNE is a dual-site experiment for long-baseline neutrino oscillation studies, neutrino astrophysics and nucleon decay searches. ProtoDUNE Dual Phase (DP) is a 6  ×  6  ×  6 m 3 liquid argon time-projection-chamber (LArTPC) that recorded cosmic-muon data at the CERN Neutrino Platform in 2019-2020 as a prototype of the DUNE Far Detector. Charged particles propagating through the LArTPC produce ionization and scintillation light. The scintillation light signal in these detectors can provide the trigger for non-beam events. In addition, it adds precise timing capabilities and improves the calorimetry measurements. In ProtoDUNE-DP, scintillation and electroluminescence light produced by cosmic muons in the LArTPC is collected by photomultiplier tubes placed up to 7 m away from the ionizing track. In this paper, the ProtoDUNE-DP photon detection system performance is evaluated with a particular focus on the different wavelength shifters, such as PEN and TPB, and the use of Xe-doped LAr, considering its future use in giant LArTPCs. The scintillation light production and propagation processes are analyzed and a comparison of simulation to data is performed, improving understanding of the liquid argon properties.

Prospects for beyond the Standard Model physics searches at the Deep Underground Neutrino Experiment: DUNE Collaboration

The Deep Underground Neutrino Experiment (DUNE) will be a powerful tool for a variety of physics topics. The high-intensity proton beams provide a large neutrino flux, sampled by a near detector system consisting of a combination of capable precision detectors, and by the massive far detector system located deep underground. This configuration sets up DUNE as a machine for discovery, as it enables opportunities not only to perform precision neutrino measurements that may uncover deviations from the present three-flavor mixing paradigm, but also to discover new particles and unveil new interactions and symmetries beyond those predicted in the Standard Model (SM). Of the many potential beyond the Standard Model (BSM) topics DUNE will probe, this paper presents a selection of studies quantifying DUNE's sensitivities to sterile neutrino mixing, heavy neutral leptons, non-standard interactions, CPT symmetry violation, Lorentz invariance violation, neutrino trident production, dark matter from both beam induced and cosmogenic sources, baryon number violation, and other new physics topics that complement those at high-energy colliders and significantly extend the present reach.

The Potential of Keratinolytic Fungi for Biotechnological Applications in Leather Manufacture

Keratinophilic fungi are present in soil as decomposers of keratinous substrates, while keratinolytic fungi have the capacity to decompose native keratin, the insoluble fibrous proteins from living organism. Keratin materials, especially by-products from food industry and animal husbandry must be harnessed through innovative, non-polluting and low-cost solutions. The nonpathogenic keratinolytic fungal species produce extracellular keratinases which have many and various applications, one being in leather industry where dehairing process of skin and hides require keratinolytic activity. The present study investigates the biodegradative potential of selected keratinolytic fungal microorganisms expressed towards different types of animal skins. The ability of Fusarium sp. 1 A strain to produce keratinase with a good activity towards animal skins was confirmed. These results suggest that after further studies, Fusarium sp.1A could play an important role in processing of animal wastes.

Nickel (II) and Cobalt (II) Complexes of Some Amino Acid-based Surfactants with Antimicrobial Activity

Nickel and cobalt complexes of lauroyl-glycine, lauroyl-glycylglycine and 1,12-dodecandioyl-diglycylglycine were synthesized. The FTIR spectroscopy confirmed the complex formation. The antimicrobial activity of synthesized nickel and cobalt complexes was investigated against several bacteria and fungi: Bacillus cereus, Pseudomonas aeruginosa, Candida albicans, and Aspergillus flavus. Generally, the nickel and cobalt complexes of the investigated surfactants showed no antimicrobial activity on Pseudomonas aeruginosa, a moderate one on Bacillus cereus and Aspergillus flavus. The most susceptible microorganism was Candida albicans, which is considered one of most common nosocomial infections. The results suggest the potential application of tested compounds as antimicrobial agents against targeted pathogens.

Effects of new beta-type Ti-40Nb implant materials, brain-derived neurotrophic factor, acetylcholine and nicotine on human mesenchymal stem cells of osteoporotic and non osteoporotic donors

Introduction

Treatment of osteoporotic fractures is still challenging and an urgent need exists for new materials, better adapted to osteoporotic bone by adjusted Young’s modulus, appropriate surface modification and pharmaceuticals.

Materials and methods

Titanium-40-niobium alloys, mechanically ground or additionally etched and titanium-6-aluminium-4-vanadium were analyzed in combination with brain-derived neurotrophic factor, acetylcholine and nicotine to determine their effects on human mesenchymal stem cells in vitro over 21 days using lactate dehydrogenase and alkaline phosphatase assays, live cell imaging and immunofluorescence microscopy.

Results

Cell number of human mesenchymal stem cells of osteoporotic donors was increased after 14 d in presence of ground titanium-40-niobium or titanium-6-aluminium-4-vanadium, together with brain-derived neurotrophic factor. Cell number of human mesenchymal stem cells of non osteoporotic donors increased after 21 d in presence of titanium-6-aluminium-4-vanadium without pharmaceuticals. No significant increase was measured for ground or etched titanium-40-niobium after 21 d. Osteoblast differentiation of osteoporotic donors was significantly higher than in non osteoporotic donors after 21 d in presence of etched, ground titanium-40-niobium or titanium-6-aluminium-4-vanadium accompanied by all pharmaceuticals tested. In presence of all alloys tested brain-derived neurotrophic factor, acetylcholine and nicotine increased differentiation of cells of osteoporotic donors and accelerated it in non osteoporotic donors.

Conclusion

We conclude that ground titanium-40-niobium and brain-derived neurotrophic factor might be most suitable for subsequent in vivo testing.

Metal release and cell biological compatibility of beta-type Ti-40Nb containing indium

Small indium (In) additions up to 5 wt % to the beta-type Ti-40Nb alloy effectively improve its mechanical biofunctionality. The impact on its biocompatibility is addressed in this work. Comparative electrochemical polarization studies and inductively coupled plasma optical emission spectrometry analyses were conducted in Tris-buffered saline (on the basis of 150 mM NaCl) with pH 7.6 and 2.0 at 310 ± 1 K with Ti-6Al-4V as reference. The metal ion releases from beta-type alloys were generally very low, for example, those of In³⁺ ions from (Ti-40Nb)-4In specimens were below 6 × 10^-7 mmol/cm² . X-ray photoelectron spectroscopy revealed the passivation mainly by Ti- and Nb-oxides with traces of In-oxides as the dominating surface process. In vitro studies demonstrate a better human bone marrow stromal cells (hBMSC) activity on the beta-type alloys in comparison to CP-Ti (grade 2), which is mainly due to their high Nb content. At 24 h after seeding on (Ti-40Nb)-4In the metabolic activity of hBMSC was 1.5-fold higher and after 11 days, the tissue non-specific alkaline phosphatase activity was 1.8-fold higher relative to values for CP-Ti. Surface treatments, like chemical etching or plasma oxidation, change the surface topography and the thickness and composition of the oxide layers, but they are not effective in further improving the cell response. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1686-1697, 2018.

Transfection-capable polycationic nanovectors which include PEGylated-cyclodextrin structural units: a new synthesis pathway

Polycationic nanoentities with low variability are able to act as cooperating carriers for dsDNA complexation and transport.

Effect of thermomechanical processing on the mechanical biofunctionality of a low modulus Ti-40Nb alloy

Different hardening strategies were evaluated regarding their potential to improve the mechanical biofunctionality of the cast and solution-treated low modulus β-Ti alloy Ti 40Nb. The strategies are based on thermomechanical treatments comprised of different hot- and cold-rolling steps, as well as annealing treatments aiming at the successive exploitation of different hardening mechanisms (grain boundary hardening, work hardening and precipitation hardening). Quasi-static tensile testing revealed that grain refinement by one order of magnitude has only a small impact on improving the mechanical biofunctionality of Ti-40Nb. However, work hardening effectively improves the tensile strength by 30% to a value of 650MPa, while retaining Young׳s modulus at 60GPa. The α-phase precipitation hardening was verified to have an increasing effect on both, strength and Young׳s modulus. Thereby, the change of Young׳s modulus dominates the change of the strength, even at low α-phase fractions. The pseudo-elastic behavior of Ti 40Nb is discussed under consideration of the microstructural changes due to the thermomechanical treatment. The texture changes evolving upon cold-rolling markedly influence the recrystallization behavior. However, the present results do not show a significant effect of the texture on the mechanical properties of Ti-40Nb.

New Cu-Free Ti-Based Composites with Residual Amorphous Matrix

Titanium-based bulk metallic glasses (BMGs) are considered to have potential for biomedical applications because they combine favorable mechanical properties and good biocompatibility. Copper represents the most common alloying element, which provides high amorphization capacity, but reports emphasizing cytotoxic effects of this element have risen concerns about possible effects on human health. A new copper-free alloy with atomic composition Ti₄₂Zr₁₀Pd₁₄Ag₂₆Sn₈, in which Cu is completely replaced by Ag, was formulated based on Morinaga's d-electron alloy design theory. Following this theory, the actual amount of alloying elements, which defines the values of covalent bond strength Bo and d-orbital energy Md, situates the newly designed alloy inside the BMG domain. By mean of centrifugal casting, cylindrical rods with diameters between 2 and 5 mm were fabricated from this new alloy. Differential scanning calorimetry (DSC) and X-rays diffraction (XRD), as well as microstructural analyses using optical and scanning electron microscopy (OM/SEM) revealed an interesting structure characterized by liquid phase-separated formation of crystalline Ag, as well as metastable intermetallic phases embedded in residual amorphous phases.

Nanostructured Ti-Zr-Pd-Si-(Nb) bulk metallic composites: Novel biocompatible materials with superior mechanical strength and elastic recovery

The microstructure, mechanical behaviour, and biocompatibility (cell culture, morphology, and cell adhesion) of nanostructured Ti45 Zr15 Pd35- x Si5 Nbx with x = 0, 5 (at. %) alloys, synthesized by arc melting and subsequent Cu mould suction casting, in the form of rods with 3 mm in diameter, are investigated. Both Ti-Zr-Pd-Si-(Nb) materials show a multi-phase (composite-like) microstructure. The main phase is cubic β-Ti phase (Im3m) but hexagonal α-Ti (P63/mmc), cubic TiPd (Pm3m), cubic PdZr (Fm3m), and hexagonal (Ti, Zr)5 Si3 (P63/mmc) phases are also present. Nanoindentation experiments show that the Ti45 Zr15 Pd30 Si5 Nb5 sample exhibits lower Young's modulus than Ti45 Zr15 Pd35 Si5 . Conversely, Ti45 Zr15 Pd35 Si5 is mechanically harder. Actually, both alloys exhibit larger values of hardness when compared with commercial Ti-40Nb, (HTi-Zr-Pd-Si ≈ 14 GPa, HTi-Zr-Pd-Si-Nb ≈ 10 GPa and HTi-40Nb ≈ 2.7 GPa). Concerning the biological behaviour, preliminary results of cell viability performed on several Ti-Zr-Pd-Si-(Nb) discs indicate that the number of live cells is superior to 94% in both cases. The studied Ti-Zr-Pd-Si-(Nb) bulk metallic system is thus interesting for biomedical applications because of the outstanding mechanical properties (relatively low Young's modulus combined with large hardness), together with the excellent biocompatibility.

Composition-dependent magnitude of atomic shuffles in Ti–Nb martensites

In this work the structural characteristics of martensitic phases in the Ti–Nb system are studied in detail. While the distortion of the orthorhombic unit cell of α′′-martensite by the addition of β-stabilizing atoms is well documented in the literature, comprehensive experimental data on the detailed atomic positions and how they vary with chemical composition are missing. For this study, a series of binary Ti–Nb alloys were prepared by casting techniques, followed by homogenization treatment and water quenching. Rietveld-based analyses of X-ray diffraction data were used to study the gradual structural changes of α′- and α′′-martensites effected by the addition of Nb, and their compositional boundaries were determined. In the case of orthorhombic α′′, it was established that, besides the lattice parameters, the positions of the atoms on the (002)α′′planes respond very sensitively to the amount of Nb present.

Intraoperative radiation therapy in gastric cancer

Gastric cancer is one of the most common malignancies worldwide. Although surgery is the only potential curative treatment, the overall survival results remain poor due to the high risks of recurrence, so scientists developed new aggressive adjuvant therapies. That is how the IORT appeared. IORT is a technique designed to provide a large radiation dose to a target tissue considered of being "at risk" to develop recurrence. In this review we resume recent publications which debate the use, efficacy and the overall survival after IORT.

Production of Porous β-Type Ti-40Nb Alloy for Biomedical Applications: Comparison of Selective Laser Melting and Hot Pressing

We used selective laser melting (SLM) and hot pressing of mechanically-alloyed β-type Ti–40Nb powder to fabricate macroporous bulk specimens (solid cylinders). The total porosity, compressive strength, and compressive elastic modulus of the SLM-fabricated material were determined as 17% ± 1%, 968 ± 8 MPa, and 33 ± 2 GPa, respectively. The alloy’s elastic modulus is comparable to that of healthy cancellous bone. The comparable results for the hot-pressed material were 3% ± 2%, 1400 ± 19 MPa, and 77 ± 3 GPa. This difference in mechanical properties results from different porosity and phase composition of the two alloys. Both SLM-fabricated and hot-pressed cylinders demonstrated good in vitro biocompatibility. The presented results suggest that the SLM-fabricated alloy may be preferable to the hot-pressed alloy for biomedical applications, such as the manufacture of load-bearing metallic components for total joint replacements.

Thermal stability and phase transformations of martensitic Ti-Nb alloys

Aiming at understanding the governing microstructural phenomena during heat treatments of Ni-free Ti-based shape memory materials for biomedical applications, a series of Ti-Nb alloys with Nb concentrations up to 29 wt% was produced by cold-crucible casting, followed by homogenization treatment and water quenching. Despite the large amount of literature available concerning the thermal stability and ageing behavior of Ti-Nb alloys, only few studies were performed dealing with the isochronal transformation behavior of initially martensitic Ti-Nb alloys. In this work, the formation of martensites (α' and α″) and their stability under different thermal processing conditions were investigated by a combination of x-ray diffraction, differential scanning calorimetry, dilatometry and electron microscopy. The effect of Nb additions on the structural competition in correlation with stable and metastable phase diagrams was also studied. Alloys with 24 wt% Nb or less undergo a [Formula: see text] transformation sequence on heating from room temperature to 1155 K. In alloys containing >24 wt% Nb α″ martensitically reverts back to β₀, which is highly unstable against chemical demixing by formation of isothermal ω_iso. During slow cooling from the single phase β domain α precipitates and only very limited amounts of α″ martensite form.

Chemical nanoroughening of Ti40Nb surfaces and its effect on human mesenchymal stromal cell response

Samples of low modulus beta-type Ti40Nb and cp2-Ti were chemically treated with 98% H2 SO4 + 30% H2 O2 (vol. ratio 1:1) solution. Surface analytical studies conducted with HR-SEM, AFM, and XPS identified a characteristic nanoroughness of the alloy surface related with a network of nanopits of ∼25 nm diameter. This is very similar to that obtained for cp2-Ti. The treatment enhances the oxide layer growth compared to mechanically ground states and causes a strong enrichment of Nb2 O5 relative to TiO2 on the alloy surface. The in vitro analyses clearly indicated that the chemical treatment accelerates the adhesion and spreading of human mesenchymal stromal cells (hMSC), increases the metabolic activity, and the enzyme activity of tissue non-specific alkaline phosphatase (TNAP). Surface structures which were generated mimic the cytoplasmic projections of the cells on the nanoscale. Those effects are more pronounced for the Ti40Nb alloy than for cp2-Ti. The relation between alloy surface topography and chemistry and cell functions is discussed.

Porous low modulus Ti40Nb compacts with electrodeposited hydroxyapatite coating for biomedical applications

Porous ß-type non-toxic Ti40Nb alloy was prepared by compaction of mechanically alloyed powder mixed with NaCl or Mg particles as space-holder material. The compacts with porosity of 36-80% demonstrated a very low Young's modulus of ~1.5-3 GPa and compression strength of ~10-35 MPa, which is suitable for potential implant material application. Porous samples were electrochemically covered with hydroxyapatite. The influence of the deposition time and of the electrolyte concentrations on the morphology of the hydroxyapatite coating was studied. It is demonstrated that a homogenous coating of hydroxyapatite crystals with different shape and size can be obtained on the surface of the porous samples.

Surface treatment, corrosion behavior, and apatite-forming ability of Ti-45Nb implant alloy

The low modulus β-type Ti-45Nb alloy is a promising new implant alloy due to its excellent mechanical biocompatibility and composition of non-toxic elements. The effect of surface treatments on the evolution of controlled topography and roughness was investigated by means of scanning electron microscopy and optical profilometry. Severe mechanical treatments, for example sand-blasting, or etching treatments in strongly oxidizing acidic solutions, like HF:HNO(3) (4:1) or H(2)SO(4):H(2)O(2) (1:1) piranha solution were found to be very effective. In particular, the latter generates a nanopatterned surface topography which is expected to be promising for the stimulation of bone tissue growth. Compared to Ti and Ti-6Al-4V, the β-type Ti-45Nb alloy requires significantly longer etching durations due to the high chemical stability of Nb. Severe surface treatments alter the passive film properties, but do not deteriorate the outstanding corrosion resistance of the Ti-45Nb alloy in synthetic body fluid environments. The Ti-45Nb appears to have a lower apatite-formation ability compared to Ti. Etching with H(2)SO(4):H(2)O(2) (1:1) piranha solution inhibits apatite formation on Ti, but not on Ti-45Nb.

Glycerol's influence on the oxidized insulin B-chain conformation in relation to the selectivity variation of subtilisin: an nuclear magnetic resonance and simulated annealing study

Glycerol, employed to mimic biological media with restricted water activity, has been shown to modify the activity of subtilisin BPN', an endopeptidase, towards the oxidized insulin B-chain, a well-studied substrate (FEBS Lett., 279 (1991) 123-131). Without minimizing the role of the microenvironment on the enzyme, we have studied the effect of glycerol addition on the structure of the enzyme substrate by homonuclear NMR spectroscopy and simulated annealing. Our results show that, in water, the oxidized insulin B-chain tertiary structure loses its central helix (residues B9-B19) and presents a folded structure with a flexible turn (residues B18-B24) in the beta-turn region of the insulin B-chain; whereas, in glycerol, the peptide is more rigid and is not folded. Moreover, in our experimental conditions, glycerol favors beta-strand secondary structure formation. Following these results, hypotheses about the differences observed in enzymatic activity on this substrate in glycerol have been postulated.