Metallosis and Corrosion Associated With Revision Total Knee Arthroplasties With Metaphyseal Sleeves

Metallosis and corrosion have been associated with metal-on-metal and modular total hip arthroplasty but are rarely described in the setting of primary or revision total knee arthroplasty (TKA). In this series, we report on cases of metallosis due to mechanically assisted crevice corrosion at modular junctions of machined trunnion-bore tapers in a revision TKA system with metaphyseal sleeves. The unique design of metal modular junctions used in sleeve-based revision TKA, along with potential patient and surgical factors, may predispose these designs to fretting, corrosion, and adverse reaction to metal debris. We now consider metallosis and corrosion in the workup of painful or failed revision TKAs with sleeves. Future studies that investigate the incidence of this phenomenon may be warranted.

High Incidence of Mechanically Assisted Crevice Corrosion at 10 Years in Non-Cemented, Non-Recalled, Contemporary Total Hip Arthroplasties

BACKGROUND

One percent to 3% of contemporary non-cemented total hip arthroplasties (THAs) present with symptomatic mechanically assisted crevice corrosion (MACC). The incidence of this problem, however, as well as the rate of asymptomatic elevations in serum cobalt, is unknown.

METHODS

Cobalt and chromium levels were obtained in conjunction with radiographs at routine 10-year surveillance follow-up of THAs from a single manufacturer with a titanium stem, cobalt alloy femoral head, and cross-linked polyethylene countersurface.

RESULTS

Ten-year follow-up of patients with 162 consecutive THAs revealed that 17 patients with 18 hips had died of unrelated causes prior to metal ion testing. Two hips were revised for other reasons, and of the remaining 142 hips, 33 were in patients who were lost, leaving 109 hips (77% of those in alive patients and unrevised for other reasons and 67% of the entire cohort) for investigation. Sixty-three patients (58%) had a serum cobalt less than 1 ppb, and 35 (32%) a cobalt of ≥1 ppb, a cutoff consistent with MACC. Of the 32 hips with definite MACC, 15 of 32 (47%) patients were symptomatic, 16 of 30 (53%) patients had adverse local tissue reaction on magnetic resonance imaging, and 19 of 32 (59%) patients have undergone revision surgery for MACC to date.

CONCLUSION

At 10-year follow-up, a minimum of 22% (35/162) of hips had a cobalt level more than 1 ppb, consistent with MACC. Symptoms and adverse local tissue reactions are each present about one-half of the time, and 59% of those with documented MACC have undergone revision.

The Mid-Atlantic Centers for AIDS Research Consortium: Promoting HIV Science Through Regional Collaboration

The Centers for AIDS Research (CFAR) program was established by the National Institutes of Health in 1988 to catalyze and support high-impact HIV research and to develop the next generation of HIV investigators at academic institutions throughout the United States. In 2014, the Penn CFAR, the Johns Hopkins University CFAR and the District of Columbia CFAR developed a partnership-the Mid-Atlantic CFAR Consortium (MACC)-to promote cross-CFAR scientific collaboration, mentoring, and communication and to address the regional HIV epidemic. Over the past 6 years, the creation of the MACC has resulted in a rich web of interconnectivity, which has fostered scientific collaboration through working groups on the black men who have sex with men (MSM) and Latinx regional HIV epidemics, joint peer-reviewed publications, and successful collaborative grant applications on topics ranging from HIV prevention in young MSM, transgender women, implementation science, and clinical epidemiology; supported developmental activities through the MACC Scholars program, cross-CFAR mentoring, joint symposia, cross-CFAR seminar participation, and keynote speakers; and promoted strategic communication through advisory committees, best practices consultations, and the social and behavioral science research network. The MACC has been highly impactful by promoting HIV science through regional collaboration, supporting a diverse network of scholars across three cities and focusing on the epidemic in underrepresented and marginalized communities. Lessons learned from this consortium may have implications for scientific research centers beyond the field of HIV.

Outcomes Following Revision for Mechanically Assisted Crevice Corrosion in a Single Femoral Design

BACKGROUND

Mechanically assisted crevice corrosion (MACC) is a described complication following metal-on-polyethylene (MoP) total hip arthroplasty (THA). The literature regarding outcomes following revision for MACC suggests that complication rates are high. The purpose of this investigation is to add to this literature with the largest reported series to date.

METHODS

This is a retrospective cohort study of 552 consecutive patients who underwent 621 MoP primary THAs. We identified patients who subsequently underwent revision THA for a diagnosis of MACC. All patients were implanted with the same implant combination (Accolade I stem/cobalt-chromium low friction ion treatment femoral head). Patient demographic, surgical, and laboratory data were collected. Follow-up was calculated from the revision surgery and Hip Disability and Osteoarthritis Outcome Score Joint Replacement and hip subjective values (HSV) were examined at final follow-up. Descriptive statistics were performed.

RESULTS

The revision rate for MACC was 11.6% and mean time to revision was 6.6 (±2.4) years. Revised patients (n = 69) had a mean preoperative serum cobalt-chromium ratio of 3.5 (±2.4). There were 8 cases of gross trunnion failure. At mean 3.2 (±1.9) years following revision, the overall major complication rate was 11.6% with a 5.8% reoperation rate. At final follow-up, mean Hip Disability and Osteoarthritis Outcome Score Joint Replacement scores were 83.2 (±15.6) and mean hip subjective value was 77.6 (±17.4). Revision resulted in significant increases in both parameters (P < .001).

CONCLUSION

The incidence of MACC in MoP THA is likely higher than previously reported, particularly for certain implant combinations. Revision surgery for MACC can achieve good outcomes but a high clinical suspicion with early detection and revision is likely key to success.

Design, Material, and Seating Load Effects on In Vitro Fretting Corrosion Performance of Modular Head-Neck Tapers

BACKGROUND

The short-term corrosion and micromechanical behavior of 32 unique head-neck taper design/material/assembly conditions was tested using an incremental cyclic fretting corrosion (ICFC) test method previously developed.

METHODS

Seven materials, design, and simulated surgical parameters were evaluated, each being assigned 2 conditions for testing, using a 2^7-2 (7 factor, quarter factorial) design of experiments test matrix. The factors explored were (1) seating load, (2) head-neck offset, (3) material combination, (4) taper diameter, (5) taper roughness, (6) angular mismatch/engagement, and (7) taper length. Each sample underwent assembly, ICFC testing, pull off.

RESULTS

Low seating load and high head offset correlated with increased fretting corrosion (P < .05). High head offset also contributed to a lower onset load for fretting current and higher micromotion (P < .05). Head subsidence measured over the ICFC test for samples seated at 100 N was significantly higher than samples seated at 4000 N. Micromotion for 12-mm head offsets was statistically higher than samples with a 1.5-mm head offset. A number of interactive effects were observed. For example, samples seated at 4000 N were less sensitive to head offset than samples seated at 100 N in terms of the resulting fretting current.

CONCLUSION

Taper locking position, material combination, taper engagement length, taper roughness, and taper dimensions all had weak or no correlation with fretting current and taper micromotion. This test method and experimental design is a versatile means of assessing potential new taper designs in the future.

Ten-Year Cross-Sectional Study of Mechanically Assisted Crevice Corrosion in 1352 Consecutive Patients With Metal-on-Polyethylene Total Hip Arthroplasty

BACKGROUND

Mechanically assisted crevice corrosion (MACC) in metal-on-polyethylene total hip arthroplasty (THA) is of concern, but its prevalence, etiology, and natural history are incompletely understood.

METHODS

From January 2003 to December 2012, 1352 consecutive THA surgeries using a titanium stem, cobalt-chromium alloy femoral head, and highly cross-linked polyethylene liner from a single manufacturer were performed. Patients were followed at 1-year and 5-year intervals for surveillance, but also seen earlier if they had symptoms. Any patient with osteolysis >1 cm (n = 3) or unexplained pain (n = 85) underwent examination, radiographs, complete blood count, erythrocyte sedimentation rate, and C-reactive protein, as well as tests for serum cobalt and chromium levels.

RESULTS

Symptomatic MACC was present in 43 of 1352 patients (3.2%). Prevalence of MACC by year of implant ranged from 0% (0 of 61, 2003; 0 of 138, 2005) to 10.5% (17 of 162; 2009). The M/L Taper stem had a greater prevalence (4.9%) of MACC than all other Zimmer (Zimmer, Inc, Warsaw, IN) 12/14 trunnion stem types combined (1.2%; P < .001). Twenty-seven of 43 (62.8%) patients have undergone revision surgery, and 16 of 43 (37.2%) patients have opted for ongoing surveillance. Comparing symptomatic THA patients with and without MACC, no demographic, clinical, or radiographic differences were found. MACC was significantly more common in 0 length femoral heads (compared with both -3.5 mm and +3.5 mm heads).

CONCLUSION

The prevalence of MACC in metal-on-polyethylene hips is higher in this cross-sectional study than previously reported. A significantly higher prevalence was found in patients with M/L Taper style stem and THA performed both in 2009 and also between 2009 and 2012 with this manufacturer.

Corrosion and adverse tissue reaction after modular unipolar hip hemiarthroplasty

Modern unipolar hip hemiarthroplasty, commonly used for displaced femoral neck fracture, is now modular, with both a variable length cobalt-chromium adapter-sleeve and large femoral head. Patients with these modular components may develop symptomatic trunnion corrosion, with elevated serum metal levels. We report the case of an 82-year-old woman, 5.5 years after a modular unipolar hip hemiarthroplasty, who presented with a 4-month history of hip pain and limp. Evaluation showed elevated serum cobalt and chromium levels and an acetabular cyst. At revision, fluid, tissue, and gross inspection were consistent with trunnion corrosion. The hip was revised with a ceramic head and dual mobility acetabular component, with a good result at 1 year. The designs of commercially available, modern unipolar hip hemiarthroplasty prostheses are reviewed.

Hormone profiles in microalgae: gibberellins and brassinosteroids

Endogenous gibberellins and brassinosteroids were quantified in 24 axenic microalgae strains from the Chlorophyceae, Trebouxiophyceae, Ulvophyceae and Charophyceae microalgae strains after 4 days in culture. This is the first report of endogenous gibberellins being successfully detected in microalgae. Between 18 and 20 gibberellins were quantified in all strains with concentrations ranging from 342.7 pg mg(-1) DW in Raphidocelis subcapitata MACC 317-4746.1 pg mg(-)(1) DW in Scotiellopsis terrestris MACC 44. Slower growing strains (S. terrestris MACC 44, Gyoerffyana humicola MACC 334, Nautococcus mamillatus MACC 716 and Chlorococcum ellipsoideum MACC 712) exhibited the highest gibberellin contents while lowest levels of gibberellins were found in faster growing strains (R. subcapitata MACC 317 and Coelastrum excentrica MACC 504). In all strains, the active gibberellin detected in the highest concentration was GA6, the predominant intermediates were GA15 and GA53 and the main biosynthetic end products were GA13 and GA51. Gibberellin profiles were similar in all strains except for the presence/absence of GA12 and GA12ald. To date this is the second report of endogenous brassinosteroids in microalgae. Brassinosteroids were detected in all 24 strains with concentrations ranging from 117.3 pg mg(-)(1) DW in R. subcapitata MACC 317-977.8 pg mg(-)(1) DW in Klebsormidium flaccidum MACC 692. Two brassinosteroids, brassinolide and castasterone were determined in all the strains. Generally, brassinolide occurred in higher concentrations than castasterone.