Extensional Rheology of Poly(vinylidene fluoride)/N,N-dimethylformamide Solutions

Typical extension flow occurs in electrospinning process of Poly(vinylidene fluoride) (PVDF) solutions such that researchers focus on extensional rheological behaviors of PVDF solutions. The extensional viscosity of PVDF solutions is measured to know the fluidic deformation in extension flows. The solutions are prepared by dissolving PVDF powder into N,N-dimethylformamide (DMF) solvent. A homemade extensional viscometric device is used to produce uniaxial extension flows and the feasibility of the viscometric device is verified by applying the glycerol as a test fluid. Experimental results show that PVDF/DMF solutions are extension shinning as well as shear shinning. The Trouton ratio of thinning PVDF/DMF solution is close to three at very low strain rate and then reaches a peak value until it drops to a small value at high strain rate. Furthermore, an exponential model may be used to fit the measured values of uniaxial extensional viscosity at various extension rates, while traditional power-law model is applicable to steady shear viscosity. For 10~14% PVDF/DMF solution, the zero-extension viscosity by fitting reaches 31.88~157.53 Pa·s and the peak Trouton ratio is 4.17~5.16 at applied extension rate of less than 34 s^-1. Characteristic relaxation time is λ~100 ms and corresponding critical extension rate is ε˙c~5 s^-1. The extensional viscosity of very dilute PVDF/DMF solution at very high extension rate is beyond the limit of our homemade extensional viscometric device. This case needs a higher sensitive tensile gauge and a higher-accelerated motion mechanism for test.

Preparation and Mounting of Whole Blood Clot Samples for Mechanical Testing

Studying and quantifying the mechanics of blood clots is essential to better diagnosis and prognosis of, as well as therapy for, thromboembolic pathologies such as strokes, heart attacks, and pulmonary embolisms. Unfortunately, mechanically testing blood clots is complicated by their softness and fragility, thus making the use of classic mounting techniques, such as clamping, challenging. This is particularly true for mechanical testing under large deformation. Here, we describe protocols for creating in vitro blood clots and securely mounting these samples on mechanical test equipment. To this end, we line 3D-printed molds with a hook-and-loop fabric that, after coagulation, provides a secure interface between the sample and device mount. In summary, our molding and mounting protocols are ideal for performing large-deformation mechanical testing, with samples that can withstand substantial deformation without delaminating from the apparatus. © 2021 Wiley Periodicals LLC. Basic Protocol 1: Cube-shaped blood clot preparation Basic Protocol 2: Sheet-shaped blood clot preparation.

A Novel Technique for Fiber Formation: Mechanotropic Spinning-Principle and Realization

We present basic experimental data and the theoretical background of a novel technique for fiber spinning from polymer solutions. The principal feature of the advanced process is realization of phase separation with detachment of a solvent, accompanied by the orientation of macromolecules, under the action of high extension rates. This is similar in some respects to dry spinning, though the driving force is not diffusion with subsequent evaporation of a solvent but redistribution of polymer-solvent interactions in favor of polymer-polymer and solvent-solvent ones governed by mechanical stresses. A promise of this approach has been demonstrated by experiments performed with polyacrylonitrile solutions in different solvents and solutions of the rigid-chain aromatic polyamide. We examined mechanotropic fiber spinning in model experiments with stretching jets from a drop of polymer solution in different conditions, and then demonstrated the possibility of realizing this process in the stable long-term continuous mode. During extension, phase separation happens throughout the whole section of a jet, as was confirmed by visual observation. Then a solvent diffuses on a jet surface, forming a liquid shell on the oriented fiber. Instability of this cover due to surface tension leads either to formation of separate solvent drops "seating" on the fiber or to the flow of a solvent down to the Taylor cone. The separate liquid droplets can be easily taken off a fiber. The physics underlying this process is related to the analysis of the influence of macromolecule coil-to-stretched chain transition on the intermolecular interaction.

Hydrophilic Channel Alignment of Perfluoronated Sulfonic-Acid Ionomers for Vanadium Redox Flow Batteries

It is known that uniaxially drawn perfluoronated sulfonic-acid ionomers (PFSAs) show diffusion anisotropy because of the aligned water channels along the deformation direction. We apply the uniaxially stretched membranes to vanadium redox flow batteries (VRFBs) to suppress the permeation of active species, vanadium ions through the transverse directions. The aligned water channels render much lower vanadium permeability, resulting in higher Coulombic efficiency (>98%) and longer self-discharge time (>250 h). Similar to vanadium ions, proton conduction through the membranes also decreases as the stretching ratio increases, but the thinned membranes show the enhanced voltage and energy efficiencies over the range of current density, 50-100 mA/cm². Hydrophilic channel alignment of PFSAs is also beneficial for long-term cycling of VRFBs in terms of capacity retention and cell performances. This simple pretreatment of membranes offers an effective and facile way to overcome high vanadium permeability of PFSAs for VRFBs.

Mechanical characterization of the rat and mice skin tissues using histostructural and uniaxial data

The skin tissue has been shown to behave like a nonlinear anisotropic material. This study was aimed to employ a constitutive fiber family equation to characterize the nonlinear anisotropic mechanical behavior of the rat and mice skin tissues in different anatomical locations, including the abdomen and back, using histostructural and uniaxial data. The rat and mice skin tissues were excised from the animals' body and then the histological analyses were performed on each skin type to determine the mean fiber orientation angle. Afterward, the preconditioned skin tissues were subjected to a series of quasi-static axial and circumferential loads until the incidence of failure. The crucial role of fiber orientation was explicitly added into a proposed strain energy density function. The material coefficients were determined using the constrained nonlinear optimization method based on the axial and circumferential extension data of the rat and mice samples at different anatomical locations. The material coefficients of the skins were given with R(2) ≥ 0.998. The results revealed a significant load-bearing capacity and stiffness of the rat abdomen compared to the rat back tissues. In addition, the mice abdomen showed a higher stiffness in the axial direction in comparison with circumferential one, while the mice back displayed its highest stiffness in the circumferential direction. The material coefficients of the rat and mice skin tissues were determined and well compared to the experimental data. The optimized fiber angles were also compared to the experimental histological data, and in all cases less than 11.85% differences were observed in both the skin tissues.