Poly(p-phenylene)-based membranes with cerium for chemically durable polymer electrolyte fuel cell membranes

A poly(p-phenylene)-based multiblock polymer is developed with an oligomeric chain extender and cerium (CE-sPP-PPES + Ce3+) to realize better performance and durability in proton exchange membrane fuel cells. The membrane performance is evaluated in single cells at 80 °C and at 100% and 50% relative humidity (RH). The accelerated stability test is conducted 90 °C and 30% RH, during which linear sweep voltammetry and hydrogen permeation detection are monitored periodically. Results demonstrate that the proton conductivity of the pristine hydrocarbon membranes is superior to that of PFSA membranes, and the hydrogen crossover is significantly lower. In addition, a composite membrane containing cerium performs similarly to a pristine membrane, particularly at low RH levels. Adding cerium to CE-sPP-PPES + Ce3+ membranes improves their chemical durability significantly, with an open circuit voltage decay rate of only 89 μV/h for 1000 h. The hydrogen crossover is maintained across accelerated stability tests, as confirmed by hydrogen detection and crossover current density. The short-circuit resistance indicates that membrane thinning is less likely to occur. Collectively, these results demonstrate that a hydrocarbon membrane with cerium is a potential alternative for fuel cell applications.

Porous Polyethylene Supports in Reinforcement of Multiblock Hydrocarbon Ionomers for Proton Exchange Membranes

Hydrocarbon (HC)-based block copolymers have been recognized as promising candidates for proton exchange membranes (PEMs) due to their distinct hydrophilic-hydrophobic separation, which results in improved proton transport compared to that of random copolymers. However, most PEMs derived from HC-based ionomers, including block copolymers, encounter challenges related to durability in electrochemical cells due to their low mechanical and chemical properties. One method for reinforcing HC-based ionomers involves incorporating the ionomers into commercially available low surface tension PTFE porous substrates. Nevertheless, the high interfacial energy between the hydrocarbon-based ionomer solution and PTFE remains a challenge in this reinforcement process, which necessitates the application of surface energy treatment to PTFE. Here, multiblock sulfonated poly(arylene ether sulfone) (SPAES) ionomers are being reinforced using untreated PE on the surface, and this is compared to reinforcement using surface-treated porous PTFE. The PE support layer exhibits a lower surface energy barrier compared to the surface-treated PTFE layer for the infiltration of the multiblock SPAES solution. This is characterized by the absence of noticeable voids, high translucency, gas impermeability, and a physical and chemical stability. By utilizing a high surface tension PE support with a comparable value to the multiblock SPAES, effective reinforcement of the multiblock SPAES ionomers is achieved for a PEM, which is potentially applicable to various hydrogen energy-based electrochemical cells.

Hydrocarbon-Based Composite Membrane Using LCP-Nonwoven Fabrics for Durable Proton Exchange Membrane Water Electrolysis

A new hydrocarbon-based (HC) composite membrane was developed using liquid crystal polymer (LCP)-nonwoven fabrics for application in proton exchange membrane water electrolysis (PEMWE). A copolymer of sulfonated poly(arylene ether sulfone) with a sulfonation degree of 50 mol% (SPAES50) was utilized as an ionomer for the HC membranes and impregnated into the LCP-nonwoven fabrics without any surface treatment of the LCP. The physical interlocking structure between the SPAES50 and LCP-nonwoven fabrics was investigated, validating the outstanding mechanical properties and dimensional stability of the composite membrane in comparison to the pristine membrane. In addition, the through-plane proton conductivity of the composite membrane at 80 °C was only 15% lower than that of the pristine membrane because of the defect-free impregnation state, minimizing the decrease in the proton conductivity caused by the non-proton conductive LCP. During the electrochemical evaluation, the superior cell performance of the composite membrane was evident, with a current density of 5.41 A/cm² at 1.9 V, compared to 4.65 A/cm² for the pristine membrane, which can be attributed to the smaller membrane resistance of the composite membrane. From the results of the degradation rates, the prepared composite membrane also showed enhanced cell efficiency and durability during the PEMWE operations.

Multi-Block Copolymer Membranes Consisting of Sulfonated Poly(p-Phenylene) and Naphthalene Containing Poly(Arylene Ether Ketone) for Proton Exchange Membrane Water Electrolysis

Glassy hydrocarbon-based membranes are being researched as a replacement for perfluorosulfonic acid (PFSA) membranes in proton exchange membrane water electrolysis (PEMWE). Here, naphthalene containing poly(arylene ether ketone) was introduced into the poly(p-phenylene)-based multi-block copolymers through Ni(0)-catalyzed coupling reaction to enhance π-π interactions of the naphthalene units. It is discovered that there is an optimum input ratio of the hydrophilic monomer and NBP oligomer for the multi-block copolymers with high ion exchange capacity (IEC) and polymerization yield. With the optimum input ratio, the naphthalene containing copolymer exhibits good hydrogen gas barrier property, chemical stability, and mechanical toughness, even with its high IEC value over 2.4 meq g−1. The membrane shows 3.6 times higher proton selectivity to hydrogen gas than Nafion 212. The PEMWE single cells using the membrane performed better (5.5 A cm−2) than Nafion 212 (4.75 A cm−2) at 1.9 V and 80 °C. These findings suggest that naphthalene containing copolymer membranes are a promising replacement for PFSA membranes in PEMWE.

Production, physiological response, and calcium and magnesium balance of lactating Holstein cows fed different sources of supplemental magnesium with or without ruminal buffer

The objective of this study was to evaluate the effects of dietary replacement of magnesium oxide (MgO) with calcium-magnesium hydroxide [CaMg(OH)₂] and its interaction with ruminal buffer (sodium sesquicarbonate) supplementation on production, Ca and Mg balance, and overall physiological response of mid-lactation Holstein dairy cows. Sixty cows averaging 40.5 ± 7.0 kg of milk/d were used. Treatments were assigned following a 2 × 2 factorial arrangement: (1) MgO, (2) MgO + buffer, (3) CaMg(OH)₂, or (4) CaMg(OH)₂ + buffer. Diets were formulated to have 16.5% of crude protein, 1.82 Mcal/kg of net energy for lactation, 0.67% Ca, 0.39% P, and 0.25% Mg, all on a dry matter (DM) basis. Treatments were individually top dressed. Milk production, composition, and DM intake were evaluated. A subsample of 20 cows were randomly selected for the evaluation of Ca and Mg balance, blood gases, and electrolytes. Ruminal fluid was also collected for evaluation of pH and Ca and Mg solubility. Effects of Mg source, buffer, and the interaction Mg source × buffer were analyzed through orthogonal contrasts. An interaction of Mg source × buffer was found for DM intake and feed efficiency, in which cows fed CaMg(OH)₂ had a similar feed efficiency regardless of ruminal buffer inclusion; however, when cows were fed MgO, the inclusion of buffer reduced feed efficiency. No effects on body weight and milk yield were observed. Buffer addition tended to increase the concentrations of fat, protein, and solids-not-fat, without affecting the yields of these milk components. Magnesium source and buffer did not affect ruminal fluid, blood, urine, or fecal pH; however, buffer supplementation increased urinary pH. Treatment with CaMg(OH)₂ increased blood concentration of HCO₃^-, total CO₂, and base excess compared with cows fed MgO. No differences were observed in the ruminal solubility of Ca and Mg or on milk or urinary Ca and Mg excretion. Greater plasma Mg concentration was observed for animals fed MgO compared with cows fed CaMg(OH)₂; however, both sources were above the threshold recommended in the literature for dairy cows. Also, a reduction in fecal Mg excretion was observed in animals fed CaMg(OH)₂. In summary, we provide evidence that CaMg(OH)₂ could replace MgO without affecting performance, overall physiological response, or Ca and Mg balance of mid-lactating dairy Holstein cows.

Aluminum Diethylphosphinate-Incorporated Flame-Retardant Polyacrylonitrile Separators for Safety of Lithium-Ion Batteries

Herein, we developed polyacrylonitrile (PAN)-based nanoporous composite membranes incorporating aluminum diethylphosphinate (ADEP) for use as a heat-resistant and flame-retardant separator in high-performance and safe lithium-ion batteries (LIBs). ADEP is phosphorus-rich, thermally stable, and flame retardant, and it can effectively suppress the combustibility of PAN nanofibers. Nanofibrous membranes were obtained by electrospinning, and the content of ADEP varied from 0 to 20 wt%. From the vertical burning test, it was demonstrated that the flame retardancy of the composite membranes was enhanced when more than 5 wt% of ADEP was added to PAN, potentially increasing the safety level of LIBs. Moreover, the composite membrane showed higher ionic conductivity and electrolyte uptake (0.83 mS/cm and 137%) compared to those of commercial polypropylene (PP) membranes (Celgard 2400: 0.65 mS/cm and 63%), resulting from interconnected pores and the polar chemical composition in the composite membranes. In terms of battery performance, the composite membrane showed highly stable electrochemical and heat-resistant properties, including superior discharge capacity when compared to Celgard 2400, indicating that the PAN/ADEP composite membrane has the potential to be used as a heat-resistant and flame-retardant separator for safe and high-power LIBs.

P–015 Characterization of ultrastructural morphology of human sperms by field-emission scanning electron microscopy using the NanoSuit method

Study question

Can the NanoSuit method to observe sperm cells in wet conditions help treat male infertility using a field emission scanning electron microscope (FE-SEM)?

Summary answer

Compared with the conventional fixation method, the NanoSuit method can easily prepare FE-SEM samples without causing contraction and denaturation of human sperm cells.

What is known already

Evaluation of sperm morphology by optical microscopy is important for identifying male infertility. FE-SEM observation is useful for a more detailed evaluation of sperm morphology; however, a lot of the morphological information of the cells is lost by chemical fixation, dehydration, and freeze-drying. The NanoSuit method enables FE-SEM observation of unfixed cells under a high vacuum environment by electron beam polymerization of extracellular substances called NanoSuit. It has been reported that a sample prepared by the NanoSuit method retains the morphological information of live cells better than a sample prepared by the conventional fixation method.

Study design, size, duration

This laboratory study was conducted with informed consent and IRB approval. Semen parameters were within the WHO normal reference range.

Participants/materials, setting, methods

The conventional fixation method sample was prepared by fixing (glutaraldehyde and osmium), dehydration (ethanol and t-butyl alcohol), and freeze-drying. The NanoSuit method sample was introduced into the FE-SEM directly without conducting the above treatments. For observation, a JSM–7100F (JEOL, Japan) was used at an acceleration voltage of 1.0 kV. The vacuum level of the observation chamber was 10–3 to 10–6 Pa.

Main results and the role of chance

Sperm head segmentation (acrosome, equatorial segment, and post acrosome), midpiece, and tail including endpiece could be clearly identified in the FE-SEM sample prepared by the NanoSuit method. Transmission electron microscopy revealed the existence of a thin polymerized extra layer, the NanoSuit, on the surface of the sperm. It is suggested that the presence of the NanoSuit layer enables FE-SEM observation of the unfixed sperm. The conventional fixation method causes a statistically significant contraction in the sperm head size compared to that calculated from optical micrographs (13.5 μm2 vs. 11.6 μm2, p < 0.001). Furthermore, wheat germ agglutinin (WGA), a lectin, which is known to have the ability to bind to the sperm surface, did not bind to the fixed FE-SEM samples. This means that the original cell surface properties are lost in the fixed sperm sample. On the other hand, the FE-SEM sample prepared by the NanoSuit method did not show a statistically significant contraction of the sperm head compared to that calculated from optical micrographs (13.2 μm2 vs 12.9 μm2, p = 0.416); it also revealed a detailed binding pattern of gold-labelled WGA to the sperm surface. These results indicate that the NanoSuit method can prepare FE-SEM samples without sperm contraction and denaturation.

Limitations, reasons for caution

Characteristic sperm morphology in patients with male infertility should be investigated in future studies.

Wider implications of the findings: The NanoSuit method does not use chemical carcinogens and can prepare an FE-SEM sample in a shorter time than the conventional fixation method. The evaluation of ultrastructural morphology of unfixed sperms by this method may be useful for the identification of new morphological features and the evaluation of male infertility.

Trial registration number

Not applicable

Cross-Linked Composite Gel Polymer Electrolyte Based on an H-Shaped Poly(ethylene oxide)-Poly(propylene oxide) Tetrablock Copolymer with SiO2 Nanoparticles for Solid-State Supercapacitor Applications

Achieving high ionic conductivity, wide voltage window, and good mechanical strength in a single material remains a key challenge for polymer-based electrolytes for use in solid-state supercapacitors (SCs). Herein, we report cross-linked composite gel polymer electrolytes (CGPEs) based on multi-cross-linkable H-shaped poly(ethylene oxide)-poly(propylene oxide) (PEO-PPO) tetrablock copolymer precursors, SiO2 nanoparticles, and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, an ionic liquid (IL). Self-standing CGPE membranes with a high IL content were prepared using in situ cross-linking reactions between the silane groups present in the precursor and the SiO2 surface. The incorporation of an optimal amount of SiO2 increased the cross-linking density of the resulting CGPE while reducing polymer-chain ordering and, consequently, increasing both ionic conductivity and mechanical strength. As a result, the CGPE with 0.1 wt % SiO2 exhibited a high ionic conductivity (2.22 × 10-3 S cm-1 at 25 °C), good tensile strength (453 kPa), and high thermal stability up to 330 °C. Finally, an all-solid-state SC assembled with the prepared CGPE showed a high operating voltage (3 V), a large specific capacitance (103.9 F g-1 at 1 A g-1), and excellent durability (94% capacitance retention over 10,000 charge/discharge cycles), which highlights its strong potential as a solid-state electrolyte for SCs.

Alcohol-Treated Porous PTFE Substrate for the Penetration of PTFE-Incompatible Hydrocarbon-Based Ionomer Solutions

For a mechanically tough proton exchange membrane, a composite membrane incorporated with a porous polymer substrate is of great interest to suppress the ionomer swelling and to improve the dimensional stability and mechanical strength of the ionomers. For the composite membranes, good impregnation of substrate-incompatible ionomer solution into the substrate pores still remains one of the challenges to be solved. Here, we demonstrated a facile process (surface treatment with solvents compatible with both substrate and the ionomer solution) for the fabrication of the composite membranes using polytetrafluoroethylene (PTFE) as a porous substrate and poly(arylene ether sulfone) (SPAES) as a hydrocarbon-based (HC) ionomer. Appropriate solvents for the surface treatment were sought through the contact angle measurement, and it was found that alcohol solvents effectively tuned the surface property of PTFE pores to facilitate the penetration of the SPAES/N-methyl-2-pyrrolidone (NMP) solution into ∼300 nm pores of the substrate. Using this simple alcohol treatment, the SPAES/NMP contact angle was reduced in half, and we could fabricate the mechanically tough PTFE/HC composite membranes, which were apparently translucent and microscopically almost void-free composite membranes.

Postpartum atypical hemolytic uremic syndrome: Evaluating thrombotic microangiopathy in the pregnant woman

Acute kidney injury in women during pregnancy and the puerperium is often ascribed to hypertensive complications of pregnancy, especially pre-eclampsia. However, rarer causes, including atypical hemolytic uremic syndrome (aHUS) can be triggered by pregnancy. We present a case of a woman with post-partum acute kidney injury due to aHUS, which was successfully treated with the C5a inhibitor eculizumab. We also present a summary of the evaluation and management of thrombotic microangiopathy in pregnancy.

Low-Voltage Reversible Electroadhesion of Ionoelastomer Junctions

Electroadhesion provides a simple route to rapidly and reversibly control adhesion using applied electric potentials, offering promise for a variety of applications including haptics and robotics. Current electroadhesives, however, suffer from key limitations associated with the use of high operating voltages (>kV) and corresponding failure due to dielectric breakdown. Here, a new type of electroadhesion based on heterojunctions between iono-elastomer of opposite polarity is demonstrated, which can be operated at potentials as low as ≈1 V. The large electric field developed across the molecular-scale ionic double layer (IDL) when the junction is placed under reverse bias allows for strong adhesion at low voltages. In contrast, under forward bias, the electric field across the IDL is destroyed, substantially lowering the adhesion in a reversible fashion. These ionoelastomer electroadhesives are highly efficient with respect to the force capacity per electrostatic capacitive energy and are robust to defects or damage that typically lead to catastrophic failure of conventional dielectric electroadhesives. The findings provide new fundamental insight into low-voltage electroadhesion and broaden its possible applications.

Functional polymers for growth and stabilization of CsPbBr3 perovskite nanoparticles

Functional polymer ligands are used to prepare perovskite nanoparticles that disperse in polymer matrices.

Reinforced anion exchange membrane based on thermal cross-linking method with outstanding cell performance for reverse electrodialysis

A poly(ethylene)-reinforced anion exchange membrane based on cross-linked quaternary-aminated polystyrene and quaternary-aminated poly(phenylene oxide) was developed for reverse electrodialysis. Although reverse electrodialysis is a clean and renewable energy generation system, the low power output and high membrane cost are serious obstacles to its commercialization. Herein, to lower the membrane cost, inexpensive polystyrene and poly(phenylene oxide) were used as ionomer backbones. The ionomers were impregnated into a poly(ethylene) matrix supporter and were cross-linked in situ to enhance the mechanical and chemical properties. Pre-treatment of the porous PE matrix membrane with atmospheric plasma increased the compatibility between the ionomer and matrix membrane. The fabricated membranes showed outstanding physical, chemical, and electrochemical properties. The area resistance of the fabricated membranes (0.69–1.67 Ω cm²) was lower than that of AMV (2.58 Ω cm²). Moreover, the transport number of PErC(5)QPS-QPPO was comparable to that of AMV, despite the thinness (51 μm) of the former. The RED stack with the PErC(5)QPS-QPPO membrane provided an excellent maximum power density of 1.82 W m⁻² at a flow rate of 100 mL min⁻¹, which is 20.7% higher than that (1.50 W m⁻²) of the RED stack with the AMV membrane.

PErC(5)QPS-QPPO exhibited 20.7% higher MPD than commercial AEM (AMV).

Hydrophilic Channel Alignment of Perfluoronated Sulfonic-Acid Ionomers for Vanadium Redox Flow Batteries

It is known that uniaxially drawn perfluoronated sulfonic-acid ionomers (PFSAs) show diffusion anisotropy because of the aligned water channels along the deformation direction. We apply the uniaxially stretched membranes to vanadium redox flow batteries (VRFBs) to suppress the permeation of active species, vanadium ions through the transverse directions. The aligned water channels render much lower vanadium permeability, resulting in higher Coulombic efficiency (>98%) and longer self-discharge time (>250 h). Similar to vanadium ions, proton conduction through the membranes also decreases as the stretching ratio increases, but the thinned membranes show the enhanced voltage and energy efficiencies over the range of current density, 50-100 mA/cm². Hydrophilic channel alignment of PFSAs is also beneficial for long-term cycling of VRFBs in terms of capacity retention and cell performances. This simple pretreatment of membranes offers an effective and facile way to overcome high vanadium permeability of PFSAs for VRFBs.

Polybenzimidazole/Nafion hybrid membrane with improved chemical stability for vanadium redox flow battery application

In order to increase the chemical stability of polybenzimidazole (PBI) membrane against the highly oxidizing environment of a vanadium redox flow battery (VRFB), PBI/Nafion hybrid membrane was developed by spray coating a Nafion ionomer onto one surface of the PBI membrane. The acid–base interaction between the sulfonic acid of the Nafion and the benzimidazole of the PBI created a stable interfacial adhesion between the Nafion layer and the PBI layer. The hybrid membrane showed an area resistance of 0.269 Ω cm² and a very low vanadium permeability of 1.95 × 10⁻⁹ cm² min⁻¹. The Nafion layer protected the PBI from chemical degradation under accelerated oxidizing conditions of 1 M VO₂⁺/5 M H₂SO₄, and this was subsequently examined in spectroscopic analysis. In the VRFB single cell performance test, the cell with the hybrid membrane showed better energy efficiency than the Nafion cell with 92.66% at 40 mA cm⁻² and 78.1% at 100 mA cm⁻² with no delamination observed between the Nafion layer and the PBI layer after the test was completed.

Novel polybenzimidazole (PBI)/Nafion hybrid membranes for the VRFB are made by spray coating a Nafion layer to protect PBI from chemical degradation.

Tunable Upper Critical Solution Temperature of Poly(N-isopropylacrylamide) in Ionic Liquids for Sequential and Reversible Self-Folding

We demonstrate sequential folding of micropatterned polymer actuators by tuning the upper critical solution temperature (UCST) of poly(N-isopropylacrylamide) (PNIPAM) copolymers in the ionic liquid (IL) 1-ethyl-3-methylimidazolium bis(trifluoro-methylsulfonyl) imide. Incorporation of comonomers having different hydrogen-bonding capacities, acrylic acid and methyl acrylate, is shown to shift the UCST of PNIPAM to higher and lower temperatures, respectively. Relying on the ability to tune the transition temperature through copolymerization along with the wide thermal range afforded by the IL as a solvent, we fabricated a photopatterned self-folding device which shows reversible and sequential bending of three sets of hinges. Such sequential and reversible bending of microactuators offers potential for the design of complex self-folding origami and soft robots.

Size Control and Fractionation of Ionic Liquid Filled Polymersomes with Glassy and Rubbery Bilayer Membranes

We demonstrate control over the size of ionic liquid (IL) filled polymeric vesicles (polymersomes) by three distinct methods: mechanical extrusion, cosolvent-based processing in an IL, and fractionation of polymersomes in a biphasic system of IL and water. For the representative ionic liquid (1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([EMIM][TFSI])), the size and dispersity of polymersomes formed from 1,2-polybutadiene-b-poly(ethylene oxide) (PB-PEO) and polystyrene-b-poly(ethylene oxide) (PS-PEO) diblock copolymers were shown to be sensitive to assembly conditions. During mechanical extrusion through a polycarbonate membrane, the relatively larger polymersomes were broken up and reorganized into vesicles with mean size comparable to the membrane pore (100 nm radius); the distribution width also decreased significantly after only a few passes. Other routes were studied using the solvent-switch or cosolvent (CS) method, whereby the initial content of the cosolvent and the PEO block length of PS-PEO were systemically changed. The nonvolatility of the ionic liquid directly led to the desired concentration of polymersomes in the ionic liquid using a single step, without the dialysis conventionally used in aqueous systems, and the mean vesicle size depended on the amount of cosolvent employed. Finally, selective phase transfer of PS-PEO polymersomes based on size was used to extract larger polymersomes from the IL to the aqueous phase via interfacial tension controlled phase transfer. The interfacial tension between the PS membrane and the aqueous phase was varied with the concentration of sodium chloride (NaCl) in the aqueous phase; then the larger polymersomes were selectively separated to the aqueous phase due to differences in shielding of the hydrophobic core (PS) coverage by the hydrophilic corona brush (PEO). This novel fractionation is a simple separation process without any special apparatus and can help to prepare monodisperse polymersomes and also separate unwanted morphologies (in this case, worm-like micelles).

Oil-in-Oil Emulsions Stabilized by Asymmetric Polymersomes Formed by AC + BC Block Polymer Co-Assembly

We demonstrate a facile route to asymmetric polymersomes by blending AC and BC block copolymers in oil-in-oil emulsions containing polystyrene (PS) and polybutadiene (PB) in chloroform (CHCl3). Polymersomes were prepared by mixing polystyrene-b-poly(ethylene oxide) (SO) and polybutadiene-b-poly(ethylene oxide) (BO) in the oil-in-oil emulsion, where the droplets and continuous phase are PS- and PB-rich, respectively. The polymersome structure was directly visualized using dye-labeled SO and BO with confocal fluorescence microscopy; SO and BO with a high O block fraction co-assemble to produce asymmetric polymersomes. As the O block is insoluble in both PS and PB, we infer that the detailed structure of the polymersomes is a bilayer in which the S and B blocks face the PS-inner and PB-outer phases, respectively, while the common O blocks form the core membrane. This structure is only observed for sufficiently long O blocks. It is remarkable that although all the polymers are soluble in CHCl3, such elaborate structures are created by straightforward co-assembly. These asymmetric polymersomes should provide robust bilayer membranes around emulsion droplets, leading to stable nanoscopic dispersions of two fluids.

Anhydrous Proton Conducting Polymer Electrolyte Membranes via Polymerization-Induced Microphase Separation

Solid-state polymer electrolyte membranes (PEMs) exhibiting high ionic conductivity coupled with mechanical robustness and high thermal stability are vital for the design of next-generation lithium-ion batteries and high-temperature fuel cells. We present the in situ preparation of nanostructured PEMs incorporating a protic ionic liquid (IL) into one of the domains of a microphase-separated block copolymer created via polymerization-induced microphase separation. This facile, one-pot synthetic strategy transforms a homogeneous liquid precursor consisting of a poly(ethylene oxide) (PEO) macro-chain-transfer agent, styrene and divinylbenzene monomers, and protic IL into a robust and transparent monolith. The resulting PEMs exhibit a bicontinuous morphology comprising PEO/protic IL conducting pathways and highly cross-linked polystyrene (PS) domains. The cross-linked PS mechanical scaffold imparts thermal and mechanical stability to the PEMs, with an elastic modulus approaching 10 MPa at 180 °C, without sacrificing the ionic conductivity of the system. Crucially, the long-range continuity of the PEO/protic IL conducting nanochannels results in an outstanding ionic conductivity of 14 mS/cm at 180 °C. We posit that proton conduction in the protic IL occurs via the vehicular mechanism and the PEMs exhibit an average proton transference number of 0.7. This approach is very promising for the development of high-temperature, robust PEMs with excellent proton conductivities.

Location and Influence of Added Block Copolymers on the Droplet Size in Oil-in-Oil Emulsions

We have investigated the effect of added polystyrene-b-poly(ethylene oxide) (SO) copolymer on the stability of oil-in-oil (O/O) emulsions containing polystyrene (PS) and poly(ethylene glycol) (PEG) in chloroform (CHCl3) and directly visualized the location of SO in the emulsions by using dye-labeled SO (SO*) with confocal laser scanning microscopy (CLSM). The emulsion formed by PS/PEG/CHCl3 = 14/6/80 (wt %) consisted of a droplet phase of PS in CHCl3 and a continuous phase containing PEG in CHCl3. SO*s with various molecular weights (Mn,SO) and volume fractions of the PS block in SO (fPS) were prepared via living anionic polymerization and subsequent end-esterification. The effect of SO on the droplet size in the emulsions was investigated as a function of both Mn,SO and fPS. Increasing Mn,SO and decreasing fPS were effective at reducing the droplet size down to less than 1 μm, which is 100 times smaller than in the absence of SO. The location of SO*s in the O/O emulsions was further investigated by CLSM. We found that the location of SO*s changed from the droplet interior to the liquid-liquid interface and then to the continuous phase with decreasing fPS. We discuss the possible mechanism in terms of the relation of SO* location to the droplet size.

Interfacial tension-hindered phase transfer of polystyrene-b-poly(ethylene oxide) polymersomes from a hydrophobic ionic liquid to water

We examine the phase transfer of polystyrene-b-poly(ethylene oxide) (PS-PEO) polymersomes from a hydrophobic ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][TFSI]), into water. The dependence of the phase transfer on the molecular weight and PEO volume fraction (fPEO) of the PS-PEO polymersomes was systematically studied by varying the molecular weight of PS (10,000-27,000 g/mol) as well as by varying the volume fraction of PEO (fPEO) between 0.1 and 0.3. We demonstrate a general boundary for the phase transfer in terms of a reduced tethering density for PEO (σPEO), which is independent of the molecular weight of the hydrophobic PS. The reduced PEO tethering density was controlled by changing the polymersome size (i.e., increased polymersome sizes increase σPEO), confirming that it is the driving force in the transfer of PS-PEO polymersomes at room temperature. The phase transfer dependence on σPEO was also analyzed in terms of the free energy of polymersomes in the biphasic system. The quality of the aqueous phase, which affects the interfacial tension of the PS membrane, influenced the phase transfer. We systematically reduced the interfacial tension by adding a water-selective solvent, THF, which has a similar effect to increasing σPEO. The results indicate that the interfacial tension between the membrane and water plays an important role in the phase transfer with the corona and that the phase transfer can be controlled either by the dimensions of the polymersomes or by the suitability of the solvent for the membrane. The interfacial tension-hindered phase transfer of polymersomes in the biphasic water-[EMIM][TFSI] system will inform the design of temperature-sensitive and reversible nanoreactors and the separation of polydisperse particles according to size by tuning the quality of the solvent.

Enhanced performance of dye-sensitized solar cells based on TiO2 nanotube membranes using an optimized annealing profile

Free standing TiO₂ nanotube membranes are transferred onto FTO slides in front-side illuminated dye-sensitized solar cells (DSSCs). The electronic properties of the tubes and, as a result, the efficiency of the DSSCs can be considerably improved by ramped annealing.

Torsion of a nongravid myomatous uterus: radiological features and literature review

Torsion of the nongravid uterus is a rare but potentially fatal acute abdominal condition. The non-specific clinical presentation of this condition makes preoperative diagnosis difficult. We describe a patient with uterine torsion in whom the diagnosis was made using contrast-enhanced computed tomography with multiplanar reconstruction. Features of uterine torsion and its complications can be demonstrated by computed tomography, which is an important means of making a preoperative diagnosis.

Differential gene expression in the perichondrium and cartilage of the neonatal mouse temporomandibular joint

Our goal was to discover genes differentially expressed in the perichondrium (PC) of the mandibular condylar cartilage (MCC) that might enhance regenerative medicine or orthopaedic therapies directed at the tissues of the temporomandibular joint. We used targeted gene arrays (osteogenesis, stem cell) to identify genes preferentially expressed in the PC and the cartilaginous (C) portions of the MCC in 2-day-old mice. Genes with higher expression in the PC sample related to growth factor ligand-receptor interactions [FGF-13 (6.4x), FGF-18 (4x), NCAM (2x); PGDF receptors, transforming growth factor (TGF)-beta and IGF-1], the Notch isoforms (especially Notch 3 and 4) and their ligands or structural proteins/proteoglycans [collagen XIV (21x), collagen XVIII (4x), decorin (2.5x)]. Genes with higher expression in the C sample consisted mostly of known cartilage-specific genes [aggrecan (11x), procollagens X (33x), XI (14x), IX (4.5x), Sox 9 (4.4x) and Indian hedgehog (6.7x)]. However, the functional or structural roles of several genes that were expressed at higher levels in the PC sample are unclear [myogenic factor (Myf) 9 (9x), tooth-related genes such as tuftelin (2.5x) and dentin sialophosphoprotein (1.6x), VEGF-B (2x) and its receptors (3-4x) and sclerostin (1.7x)]. FGF, Notch and TGF-beta signalling may be important regulators of MCC proliferation and differentiation; the relatively high expression of genes such as Myf6 and VEGF-B and its receptors suggests a degree of unsuspected plasticity in PC cells.

Transcriptome analysis of the salivary glands of the female tick Amblyomma americanum (Acari: Ixodidae)

Ticks infest a wide range of hosts while bypassing their immune, inflammatory and haemostatic responses during their extended feeding, which may last for more than two weeks. Here, we present a transcriptome analysis of 3868 expressed sequence tags (ESTs) from three cDNA libraries generated from the salivary glands of adult female Ambyomma americanum ticks at different stages of feeding. We applied a normalization step for one library, significantly decreasing the abundance of mitochondrial sequences amongst the 2292 sequences from the normalized library. Our ESTs include homologues that may modulate haemostatic, immune and inflammatory responses of the hosts. Other ESTs probably represent important components of the highly efficient secretory pathways for salivary proteins and concomitantly transmitted pathogens.

Phase I/II study of PHY906/capecitabine in hepatocellular carcinoma

15152

Traditional botanical formulations in combination with conventional antitumor chemotherapeutics may prove a powerful approach in reducing toxicity and improving clinical outcomes. In vivo studies show that PHY906, a traditional Chinese formulation, can reduce chemo-induced gastrointestinal toxicity while enhancing the therapeutic efficacy of a broad-spectrum of common anticancer agents in various cancer models, including capecitabine, CPT-11, thalidomide, adriamycin, and sorafenib in liver cancer; gemcitabine, capecitabine, oxaliplatin, gem/ox in pancreatic cancer; and CPT-11, 5-FU, sorafenib, VP-16, L-OddC, CPT-11/5-FU/LV, and oxaliplatin/5-FU/LV in colorectal cancer. Co- administration of PHY906 with a host of chemotherapeutic agents appears to neither alter the pharmacokinetic profiles of the chemotherapeutic agents nor their respective metabolites. PHY906 is currently being studied in a phase I/II, multicenter, open-label, dose-modification, safety and efficacy study in combination with capecitabine in patients with non-resectable HCC in the U.S. and Taiwan. Phase I patients (n=18) were enrolled at COH, Yale, VA and Stanford beginning November 2003. The primary objective of phase I was the determination of a safe dose regimen by varying the dose levels of PHY906 and/or capecitabine. Three dose levels of PHY906 + capecitabine were evaluated: PHY906 1000 mg BID + Capecitabine 1000 mg/m2 BID; PHY906 600 mg BID + Capecitabine 750 mg/m2 BID; and PHY906 800 mg BID + Capecitabine 750 mg/m2 BID. The final dosing level was chosen for the phase II portion of the study. Preliminary results suggest that the quality of life of patients on PHY906 + capecitabine was improved when compared to historical controls studying capecitabine alone. There is also no evidence of drug-induced toxicity caused by PHY906; nor does PHY906 reduce capecitabine antitumor activity. For patients receiving capecitabine at 750 mg/m2 BID and PHY906 at either 600 mg BID (N=4) or 800 mg BID (N=24), 10.7% (N=3) achieved minor response (MR), 50% (N=14) had stable disease (SD) and 39.3% (N=11) had progressive disease (PD). These findings support the further investigation of PHY906 as an adjuvant therapy of capecitabine in a larger HCC population.

No significant financial relationships to disclose.

Intra-cavity side-pumped Ho:YAG laser

We present a novel, compact and power scalable Ho:YAG laser based on intracavity side-pumping by a high-power Tm:YLF slab laser. 14 W of continuous wave output power is obtained at 2.09 microm in the current experiments, with the clear prospect of reaching the 100 W regime in a power scaled version.

Superselective coil embolization in gastrointestinal haemorrhage: early experience

This is a retrospective study to evaluate our early experience of using selective microcoil embolization in patients who had gastrointestinal (GI) haemorrhage. From December 2002 to December 2003, six patients with GI haemorrhage (upper GI, n = 1; lower GI, n = 5) underwent superselective microcoil embolization. Microcatheters were used to carry out embolizations in branches of the superior mesenteric artery. Microcoils were used in five patients and a combination of microcoils and embolospheres was used in one patient. Technical success (bleeding target devascularization) was achieved in all patients who showed active bleeding at the time of angiography. Two patients had recurrent bleeding within 24 h of embolization, of which one (16.7%) died. The other patient did not require active intervention as bleeding was minimal and resolved with conservative management. Satisfactory clinical success (no rebleeding after 30 days) was achieved in five patients. No clinical signs and symptoms of bowel ischaemia occurred in these patients. Follow-up colonoscopy carried out in two patients did not show any signs of ischaemia in the affected bowel segments. Superselective microcoil embolization is an effective and safe method of controlling and arresting bleeding in GI haemorrhage.

Allelic variants of ovine prion protein gene (PRNP) in Oklahoma sheep

1,144 sheep belonging to 21 breeds and known crosses were sequence analyzed for polymorphisms in the ovine PRNP gene. Genotype and allele frequencies of polymorphisms in PRNP known to confer resistance to scrapie, a fatal neurodegenerative disease of sheep, are reported. Known polymorphisms at codons 136 (A/V), 154 (H/R) and 171 (Q/R/H/K) were identified. The frequency of the 171R allele known to confer resistance to type C scrapie was 53.8% and the frequency of the 136A allele known to influence the resistance to type A scrapie was 96.01%. In addition, we report the identification of five new polymorphisms at codons 143 (H/R), 167 (R/S), 180 (H/Y), 195 (T/S) and 196 (T/S). We also report the identification of a novel allele (S/R) at codon 138.

Fig-eating by vertebrate frugivores: a global review

The consumption of figs (the fruit of Ficus spp.: Moraceae) by vertebrates is reviewed using data from the literature, unpublished accounts and new field data from Borneo and Hong Kong. Records of frugivory from over 75 countries are presented for 260 Ficus species (approximately 30% of described species). Explanations are presented for geographical and taxonomic gaps in the otherwise extensive literature. In addition to a small number of reptiles and fishes, 1274 bird and mammal species in 523 genera and 92 families are known to eat figs. In terms of the number of species and genera of fig-eaters and the number of fig species eaten we identify the avian families interacting most with Ficus to be Columbidae, Psittacidae, Pycnonotidae, Bucerotidae, Sturnidae and Lybiidae. Among mammals, the major fig-eating families are Pteropodidae, Cercopithecidae, Sciuridae, Phyllostomidae and Cebidae. We assess the role these and other frugivores play in Ficus seed dispersal and identify fig-specialists. In most, but not all, cases fig specialists provide effective seed dispersal services to the Ficus species on which they feed. The diversity of fig-eaters is explained with respect to fig design and nutrient content, phenology of fig ripening and the diversity of fig presentation. Whilst at a gross level there exists considerable overlap between birds, arboreal mammals and fruit bats with regard to the fig species they consume, closer analysis, based on evidence from across the tropics, suggests that discrete guilds of Ficus species differentially attract subsets of sympatric frugivore communities. This dispersal guild structure is determined by interspecific differences in fig design and presentation. Throughout our examination of the fig-frugivore interaction we consider phylogenetic factors and make comparisons between large-scale biogeographical regions. Our dataset supports previous claims that Ficus is the most important plant genus for tropical frugivores. We explore the concept of figs as keystone resources and suggest criteria for future investigations of their dietary importance. Finally, fully referenced lists of frugivores recorded at each Ficus species and of Ficus species in the diet of each frugivore are presented as online appendices. In situations where ecological information is incomplete or its retrieval is impractical, this valuable resource will assist conservationists in evaluating the role of figs or their frugivores in tropical forest sites.

A 100% 2-year graft survival can be attained in high-risk 15-kg or smaller infant recipients of kidney allografts

BACKGROUND

Infants make up the most high-risk, difficult to care for subgroup undergoing kidney transplantation, with the lowest 1- and 2-year graft survival rates of any other age group. The principal causes of graft loss have been graft thrombosis, primary nonfunction, technical error, and irreversible acute rejection.

HYPOTHESIS

Infants undergoing kidney transplantation can achieve near 100% graft survival at 2 years following surgery, despite their very high-risk status.

DESIGN

Analysis of 45 consecutive kidney transplants performed in patients weighing less than or equal to 15 kg during an 8-year period beginning August 1991. Patients included complex referrals from throughout the United States and all received transplants and were cared for by the same pediatric kidney transplantation team.

RESULTS

Mean weight at transplantation was 11. 2 kg. Renal failure was due to congenital or urologic causes in the majority (53%) of cases. Size-discrepant adult-sized kidney grafts were transplanted in 80% of patients; 64% received live-donor grafts; 78% were receiving dialysis prior to transplantation; and 27% had extremely small bladders (<20 cm(3)) requiring modification of the ureteral implantation. Excluding 1 transplant-unrelated death, graft and patient survival at 2 years was 100%. Eight-year patient and graft survival rates (for our combined live and cadaver donor series) were 89.6% and 84.6%, respectively. This compares favorably with much lower graft survival in low-risk adult recipients. Delayed graft function occurred in only 1 patient (2%). Rate of incidence of rejection was 9.3% within 2 years of transplantation and the overall rejection rate was 15.5%. No graft was lost to vascular thrombosis, primary nonfunction, technical error, or acute rejection. The mean creatinine level was 53.04 micromol/L (0.6 mg/dL) and 61.9 micromol/L (0.7 mg/dL) at 1 and 2 years, respectively, and 88.4 micromol/L (1.0 mg/dL) at 3, 4, and 5 years after transplantation.

CONCLUSION

One hundred percent 2-year and excellent 8-year graft survival rates can be achieved in what has historically been the highest-risk and most difficult to care for patient subgroup undergoing kidney transplantation.

Intravenous ribavirin therapy for adenovirus pneumonia

We report on the effectiveness of intravenous ribavirin for severe adenoviral pneumonia in a 10-month-old male following orthotopic liver transplantation. On day 20 post-transplantation, he developed high fever, marked respiratory compromise, and hypoxemia. The chest radiograph showed bilateral pulmonary infiltrates. Samples of bronchoalveolar lavage fluid grew adenovirus, serotype 1. Marked clinical and radiological improvement was noted after intravenous ribavirin therapy. A prospective clinical trial is needed to determine the efficacy of ribavirin therapy for severe adenovirus disease.

Significance of detecting Epstein-Barr-specific sequences in the peripheral blood of asymptomatic pediatric liver transplant recipients

Pediatric allograft recipients are at increased risk for Epstein-Barr virus (EBV)-associated illnesses. The early identification and diagnosis of EBV-associated disorders is critical because disease progression can often be curtailed by modification of immunosuppression. We have previously shown that detection of EBV-specific sequences in the circulation by polymerase chain reaction (PCR) correlated well with the clinical symptoms of EBV infection. The purpose of the current study is to determine the significance of detecting EBV-specific sequences by PCR in asymptomatic pediatric liver transplant recipients. Peripheral-blood DNA was analyzed for the EBV genes, coding from the nuclear antigen 1 (EBNA-1) and the viral capsid antigen (gp220) by PCR. Samples from asymptomatic pediatric liver transplant recipients were analyzed from the immediate postoperative period and at 2- to 4-month intervals thereafter. We followed up 13 of these asymptomatic recipients who tested positive for EBV compared with 7 asymptomatic recipients who tested negative for EBV during the early posttransplantation period. Follow-up ranged from 1.5 to 4 years posttransplantation. Nine patients (69%) initially positive for EBV and asymptomatic ultimately developed symptoms of EBV infection, including fever, lymphadenopathy, rash, respiratory and gastrointestinal symptoms, and/or hepatitis. Five of these patients (56%) went on to develop posttransplant lymphoproliferative disorder based on histological examination of biopsied tissue and immunohistochemical identification of the EBV antigen/DNA in tissue. This is the first report suggesting that detection of EBV-specific sequences in the absence of symptoms may herald impending EBV-associated disorders. Thus, routine monitoring for circulating EBV sequences in asymptomatic recipients may be useful in the early identification of those at risk for developing EBV-associated disease and its ultimate prevention.