Gold leaf electrochemical flow cell for determination of iodide in nuclear emergency tablets

This work introduces an innovative gold-leaf flow cell for electrochemical detection in flow injection (FI) analysis. The flow cell incorporates a hammered custom gold leaf electrochemical sensor. Hammered gold leaves consist of pure gold and are readily available in Thailand at affordable prices (approximately $0.085 for a sheet measuring 40 mm × 40 mm). Four sensing devices can be made from a single sheet of this gold leaf, resulting in a production cost of approximately $0.19 per sensor. Each electrochemical sensor has the gold leaf as the working electrode, together with a printed carbon strip, and a printed silver/silver chloride strip as the counter and reference electrodes, respectively. Initial investigations using cyclic voltammetry of a standard 1000 μmol L⁻1 iodide solution in 60 mmol L⁻1 phosphate buffer (PB) solution at pH 5, demonstrated performance comparable to that of a commercial screen-printed gold electrode. The hammered gold leaf electrode was then installed in a commercial flow cell as part of an FI system. A sample or standard iodide solution (100 μL) is injected into the first carrier stream of phosphate buffer (PB) solution, which then merges to mix with the second stream of the same buffer solution before flowing into the flow cell for amperometric detection of iodide. The optimized operating conditions include a fixed potential of +0.39 V (vs Ag/AgCl), and a total flow rate of 3 mL min⁻1. A linear calibration is obtained in the concentration range of 1 to 1000 μmol L⁻1 I- with a typical equation of μA = (0.00299 ± 0.00004) × (μmol L-1 I-) + (0.021 ± 0.020), and R2 = 0.9994. Analysis of iodide using this gold leaf-FI system is rapid with sample throughput of 86 samples h⁻1 and %RSD of a sample of 100 μmol L⁻1 I⁻ of 1.2 (n = 29). The limit of detection, (calculated as 2.78 × SD of regression line/slope), is 27 μmol L⁻1 I-. This method was successfully applied to determine iodide in nuclear emergency tablets.

Disposable Microchamber with a Microfluidic Paper-Based Lid for Generation and Membrane Separation of SO2 Gas Employing an In Situ Electrochemical Gas Sensor for Quantifying Sulfite in Wine

This work presents a fully disposable microchamber for gas generation of a sample solution. The microchamber consists of a cylindrical well-reactor and a paper-based microfluidic lid (μFluidic lid), which also serves as the reagent loading and dispensing unit. The base of the reactor consists of a hydrophobic membrane covering an in-house graphene electrochemical gas sensor. Fabrication of the gas sensor and the three-layer μFluidic lid is described. The μFluidic lid is designed to provide a steady addition of the acid reagent into the sample solution instead of liquid drops from a disposable syringe. There are three steps in the procedure: (i) acidification of the sample in the reactor to generate SO₂ gas by the slow dispensing of the acid reagent from the μFluidic lid, (ii) diffusion of the liberated SO₂ gas through the hydrophobic membrane at the base of the reactor, and (iii) in situ detection of SO₂ by cathodic reduction at the graphene electrode. The device was demonstrated for quantitation of the sulfite preservative in wine without heating or stirring. The selectivity of the analysis is ensured by the combination of the gas-diffusion membrane and the selectivity of the electrochemical sensor. The linear working range is 2-60 mg L^-1 SO₂, with a limit of detection (3SD of intercept/slope) of 1.5 mg L^-1 SO₂. This in situ method has the shortest analysis time (8 min per sample) among all voltammetric methods that detect SO_2(g) via membrane gas diffusion.

Simple gunshot residue analyses for estimating firing distance: Investigation with four types of fabrics

This work presents two simple methods for estimating the firing distance from the gunshot residues (GSRs) on fabric targets. Four types of fabric targets, namely twill weave denim cotton-polyester (80/20), jersey knitting 100% cotton, plain weave cotton-polyester (80/20) and plain weave cotton-polyester (60/40), were employed. The firing tests were carried out using these white fabrics as targets at distances of 5-100 cm, respectively. In the first method, digital images of the black GSRs on fabric materials were recorded inside an illuminated box and the inverted gray intensity values were plotted against the firing distances. Since the plots of all fabrics are not significantly different, the estimation of firing distance employs the same exponential curve for all test fabrics. Although simple, the imaging method is not suitable for dark-colored materials. A chemical-based method was therefore developed as an alternative method. In the second method, a small disposable microfluidic paper-based analytical device (μPAD) was employed for detecting Pb(II) extracted from the GSRs. The μPAD method uses the measurement of the length of a narrow band of a pink color resulting from reaction between rhodizonate reagent and the Pb(II) extract. The plots indicated that the data of thick denim material are significantly different to other test fabrics which are much thinner. These three fabrics share the same estimation curve. However, it is recommended that the separate estimation curve for denim materials must be used. Both methods are suitable for short range firing distance, no further than 60 cm, since at greater distances the inverted gray intensity and the 'band-length' methods are unable to detect the GSRs.

Simplified Fabrication of Laminated Paper-Based Analytical Device (LPAD) with Color-Palette Mobile App for Analysis of Salicylic Acid in Pharmaceutical Products

In this work, we present for the first time, a simplified fabrication of a laminated paper-based analytical device (LPAD) with a free-mobile app, Palette Cam, for image analysis. A filter paper is cut in a rectangular shape (9 × 3 cm) and placed between a top laminating sheet with punched holes and a bottom laminating sheet. The holes allow accessibility of liquid on the paper. Thermal lamination is then employed to complete the fabrication of LPAD. Our simplified design reduces a tedious alignment of small pieces of paper to the holes. We demonstrated the LPAD with an analysis of salicylic acid in pharmaceutical products. Each 4 μL of ferric reagent and sample was dispensed on the LPAD. Smartphone was used to capture images. The RGB (red green blue) color intensity from the Palette Cam was converted into a logarithm color ratio. Our LPAD is simplified, cost-effective and able to be a portable device.

WinMLR program for the determination of sorbic and benzoic acids in food samples

The program WinMLR has been developed to quantify sorbic and benzoic acids in soft drinks, fruit juices, and soy sauce by making a multilinear regression treatment of experimental data to a linear combination of standard signals. The spectra of sorbic and benzoic acid and samples were obtained from a conventional spectrophotometer, which has been saved in an ASCII file to be applied with the WinMLR program. Before to determine sorbic and benzoic acids in samples, the wavelength validation and calibration parameters were studied. Standard solutions of sorbic and benzoic acids were used for the calibration parameters to measure the individual analyte. If the sample has simultaneously both compounds, it is better to choose the synthetic mixture for the calibration parameters. This technique provides a good recovery in the range of 80.4-104.8% without a complicated and expensive instrument.

Development of a microfluidic membraneless vaporization flow system for trace analysis of arsenic

A new design of a membraneless vaporization (MBL-VP) unit coupled with a specific flow system is presented for the determination of arsenic at trace levels using a hydride generation process. The MBL-VP unit contains two concentric conical reservoirs, with the outer cone selected as the donor reservoir. The volume of the outer donor reservoir is thereby greater than the acceptor volume, necessary for holding sufficient sample and reagents for the generation of arsine gas by reaction between As(iii) and sodium borohydride under acidic conditions. The arsine gas diffuses into the narrow headspace and is absorbed by an aliquot of 150 μL of mercuric chloride acceptor solution. The resulting reaction produces hydronium ions which is monitored by the absorbance change at 530 nm of the methyl orange indicator added in the acceptor solution. To decrease the detection limit, the aspiration and removal of the donor plug, comprising the sample, borohydride and acid, into and out of the donor cone are repeated several times, while the acceptor solution is kept unchanged. As a result, analysis of arsenic was achieved in the range of 10 to 100 μg L-1 with a detection limit of 8 μg L-1. Application to surface water was investigated. Percent recoveries of spiked surface water samples were in the range of 94-110%. For comparison of total arsenic (As(iii) and As(v)), the results obtained from the developed method are not statistically different from the ICP-OES method.

Simple Flow-Based System with an In-Line Membrane Gas-liquid Separation Unit and a Contactless Conductivity Detector for the Direct Determination of Sulfite in Clear and Turbid Food Samples

This study presents a simple flow-based system for the determination of the preservative agent sulfite in food and beverages. The standard method of conversion of sulfite ions into SO₂ gas by acidification is employed to separate the sulfite from sample matrices. The sample is aspirated into a donor stream of sulfuric acid. A membrane gas–liquid separation unit, also called a ‘gas-diffusion (GD)’ unit, incorporating a polytetrafluoroethylene (PTFE) hydrophobic membrane allows the generated gas to diffuse into a stream of deionized water in the acceptor line. The dissolution of the SO₂ gas leads to a change in the conductivity of water which is monitored by an in-line capacitively coupled contactless conductivity detector (C4D). The conductivity change is proportional to the concentration of sulfite in the sample. In this work, both clear (wine) and turbid (fruit juice and extracts of dried fruit) were selected to demonstrate the versatility of the developed method. The method can tolerate turbidity up to 60 Nephelometric Turbidity Units (NTUs). The linear range is 5–25 mg L⁻¹ SO₃²⁻ with precision <2% RSD. The flow system employs a peristaltic pump for propelling all liquid lines. Quantitative results of sulfite were statistically comparable to those obtained from iodimetric titration for the wine samples.

Dual-Purpose Photometric-Conductivity Detector for Simultaneous and Sequential Measurements in Flow Analysis

This work presents a new dual-purpose detector for photometric and conductivity measurements in flow-based analysis. The photometric detector is a paired emitter-detector diode (PEDD) device, whilst the conductivity detection employs a capacitively coupled contactless conductivity detector (C4D). The flow-through detection cell is a rectangular acrylic block (ca. 2 × 2 × 1.5 cm) with cylindrical channels in Z-configuration. For the PEDD detector, the LED light source and detector are installed inside the acrylic block. The two electrodes of the C4D are silver conducting ink painted on the PEEK inlet and outlet tubing of the Z-flow cell. The dual-purpose detector is coupled with a sequential injection analysis (SIA) system for simultaneous detection of the absorbance of the orange dye and conductivity of the dissolved oral rehydration salt powder. The detector was also used for sequential measurements of creatinine and the conductivity of human urine samples. The creatinine analysis is based on colorimetric detection of the Jaffé reaction using the PEDD detector, and the conductivity of the urine, as measured by the C4D detector, is expressed in millisiemens (mS cm-1).

Catalytic remediation of phenol contaminated wastewater using Cu–Zn hydroxide nitrate

This work highlights an application of Cu–Zn hydroxide nitrate (denoted as 6Cu–Zn) as a highly effective and reusable catalyst for catalytic wet peroxide oxidation of phenol under mild conditions (35 °C).

Membraneless vaporization unit for direct analysis of solid sample

A new apparatus, called 'membraneless vaporization' (MBL-VP) unit was designed and developed for direct analysis of solid samples. Solid analyte was converted into a gaseous form which then reacts with an indicator reagent. Change in absorbance was used to quantitate the analyte. Stirring with a magnetic bar was employed to facilitate the evaporation of the gas. Unlike the pervaporation technique, hydrophobic membrane was not required for this MBL-VP technique. Application of the membraneless technique for direct determination of calcium carbonate in calcium supplements, has shown to be very precise (R.S.D.=2.5% for 0.16 mmol CO3(2-)), with detection limit of 0.5 mg CaCO3. Results by this method agreed well with flame atomic absorption spectrometric method. Sample throughput was 20 samples h(-1).

Novel oxidation reaction of prochlorperazine with bromate in the presence of synergistic activators and its application to trace determination by flow injection/spectrophotometric method

A simple and fast flow injection spectrophotometric method for the determination of bromate in water samples was developed. The detection system is based on the oxidation of prochlorperazine (PCP) with bromate in strongly acidic medium. Large amounts of chloride and bromide was found, for the first time, to act as an activator, and to enhance the sensitivity for bromate detection. The oxidation product of PCP gives pink color, which can be used to monitor the reaction spectrophotometrically at 525 nm. Under the optimal conditions, the method is selective; only nitrite, chlorite and hypochlorite can interfere with the determination of bromate. The elimination of these three ions is discussed. The calibration graph for bromate determination was linear in the range of 10-130 microg L(-1) with a detection limit of 2.3 microg L(-1). The repeatability was satisfactory, with the relative standard deviation of 1.1% (25 microg L(-1), n=10). The sample throughput was 44 h(-1). The proposed method was found to be highly reliable for screening drinking waters containing bromate, which is above or below legislation limit of 10 microg L(-1).

Simple and selective method for determination of iodide in pharmaceutical products by flow injection analysis using the iodine-starch reaction

This work exploited the well-known iodine-starch reaction for development of a simple flow-injection (FI) method for determination of iodide in pharmaceutical samples. Iodide in an injected zone was oxidized to iodine. A gas diffusion unit enables selective permeation of iodine through a hydrophobic membrane. Detection was made very selective for elemental iodine by employing formation of the I(3)(-)-starch complex. The detection limit (3 S/ N) of the system was 1 mg I L(-1). For a liquid patent medicine used for asthma treatment we suggested modification of the system. Direct injection of this sample, which contains a particularly high concentration level of iodide (ca. 9000 mg I L(-1)), can be achieved by coupling a dialysis unit to the FI system. This has increased the working range to 6000-10,000 mg I L(-1) without employing complicated nanoliter injection.