Improvement of heat transfer within phase change materials using V-shaped rods

This study numerically investigated the improvement of heat transmission to phase change material (PCM) paraffin wax in a triangular cell with and without fins. The enthalpy-porosity combination was quantitatively evaluated using the ANSYS/FLUENT 20 program. Materials with the phase shifts of paraffin wax were used in this study (RT42). According to the study findings, fins significantly accelerate the melting process and decrease the time required to finish it. The time difference between melting with and without fins is 125%. Moreover, the inclusion of v-shaped fins contributed to a 200% reduction in the melting process time. Thus, the use of v-shaped fins facilitates faster heat transfer to and from the applications wherein the phase change materials are used.

Investigating the physicochemical properties of solid dispersions based on semicrystalline carriers: A case study with ketoprofen

Hydrophilic semicrystalline carriers represent an alternative to amorphous polymers due to their low melting temperature, useful for the production of solid dispersions (SDs) by melting-based technologies. This research aims to compare SDs of ketoprofen (KET) and three different semicrystalline carriers (PEG, Poloxamer and Gelucire) regarding miscibility, phase behavior, molecular interactions and stability. KET was chosen owing to its low solubility and high glass forming ability. Estimation of drug-excipient miscibility was performed by Flory-Huggins theory. Negative Gibbs free energy indicated a spontaneous mixing of KET with the three carriers and miscibility in the order PEG > Poloxamer > Gelucire. SDs up to 40 % w/w of drug were produced by melting process at a temperature below KET melting point. Characterization of SDs was performed by differential scanning calorimetry, polarized light microscopy and powder X-ray diffraction. In case of PEG and Poloxamer, the drug incorporation did not affect carrier crystallinity, while KET was in the amorphous state. Differently, KET retarded the crystallization of Gelucire and at high drug loadings the SDs were amorphous and semisolid. FT-IR analysis revealed a strong interaction between KET and the three carriers. Finally, PEG-based SDs above 20 % KET loading displayed drug crystallization after 6 months of storage; while Poloxamer and Gelucire-based SDs showed KET crystallization only at 40 % KET. Due to its less hydrophilic character and limited water uptake, Gelucire showed the best stability among the three excipients.

Photobleaching reduces the contribution of dissolved organic carbon to glacier melting in the Himalayas and the Tibetan Plateau

Dissolved organic carbon (DOC) makes an important contribution to glacier melting in the Himalayas and the Tibetan Plateau (HTP). Photobleaching can effectively reduce the light absorption ability of DOC, further changing its impact on glacier melting, which is not yet well researched in the HTP. Therefore, snowpit samples from the Bayi, Ganglongjiama (GLJM), Jiemayangzong (JMYZ) and Demula (DML) glaciers were collected to study the influence of photobleaching on the light absorption ability of DOC and its impact on glacier melting. The results showed that the DOC concentration of snowpit samples, which was affected by the melting state and photobleaching, decreased from the northern HTP to the southern HTP. At an early stage of melting, the mass absorption cross-section value at 365 nm (MAC₃₆₅) values showed a negative correlation with DOC concentrations in the snowpit at the JMYZ and DML glaciers, indicating that colored DOC tended to be concentrated in the snowpit during the melting process. With the aggravation of ablation, some snowpit samples in the GLJM and Bayi glaciers had both low concentrations and MAC₃₆₅ values of DOC due to the reduced influence of photobleaching on the light absorption ability of DOC. Similarly, two fluorescence components (one protein-like component and one humic-like component) were identified in the extracted DOC at the JMYZ and DML glaciers, while those components were not detected in the GLJM glacier. Based on the sources of fluorescent DOC and five-day backward air mass trajectories, long-distance transport of pollutants from South Asia was an important source of snowpit DOC in the southern HTP. In this study, photobleaching can effectively remove colored and fluorescent DOC from snowpit samples in the HTP, further reducing the radiation forcing and glacier melting caused by DOC.

Pharmaceutical amorphous solid dispersion: A review of manufacturing strategies

Amorphous solid dispersions (ASDs) are popular for enhancing the solubility and bioavailability of poorly water-soluble drugs. Various approaches have been employed to produce ASDs and novel techniques are emerging. This review provides an updated overview of manufacturing techniques for preparing ASDs. As physical stability is a critical quality attribute for ASD, the impact of formulation, equipment, and process variables, together with the downstream processing on physical stability of ASDs have been discussed. Selection strategies are proposed to identify suitable manufacturing methods, which may aid in the development of ASDs with satisfactory physical stability.

Carbonaceous matter in glacier at the headwaters of the Yangtze River: Concentration, sources and fractionation during the melting process

Carbonaceous matter has an important impact on glacial retreat in the Tibetan Plateau, further affecting the water resource supply. However, the related studies on carbonaceous matter are still scarce in Geladaindong (GLDD) region, the source of the Yangtze River. Therefore, the concentration, source and variations of carbonaceous matter at Ganglongjiama (GLJM) glacier in GLDD region were investigated during the melting period in 2017, which could deepen our understanding on carbonaceous matter contribution to glacier melting. The results showed that dissolved organic carbon (DOC) concentration of snowpit samples (283 ± 200 μg/L) was much lower than that of precipitation samples (624 ± 361 μg/L), indicating that large parts of DOC could be rapidly leached from the snowpit during the melting process. In contrast, refractory black carbon (rBC) concentration measured by Single Particle Soot Photometer of snowpit samples (4.27 ± 3.15 μg/L) was much higher than that of precipitation samples (0.97 ± 0.49 μg/L). Similarly, DOC with high mass absorption cross-section measured at 365 nm value was also likely to enrich in snowpit during the melting process. In addition, it was found that both rBC and DOC with high light-absorbing ability began to leach from the snowpit when melting process became stronger. Therefore, rBC and DOC with high light-absorbing ability exhibited similar behavior during the melting process. Based on relationship among DOC, rBC and K⁺ in precipitation, the main source of carbonaceous matter in GLJM glacier was biomass burning during the study period.

Dissolved organic carbon fractionation accelerates glacier-melting: A case study in the northern Tibetan Plateau

In glacierized regions, melting process has a significant effect on concentrations and light absorption characteristics of dissolved organic carbon (DOC), potentially resulting in variations of its radiative forcing, which is not yet relevant research at glacier region of the Tibetan Plateau (TP). In this study, DOC fractionation and its radiative forcing change during the melting process were investigated at Laohugou glacier No. 12 (LHG glacier) in western Qilian Mts., northern TP. DOC concentrations in fresh snow, snowpit and surface ice samples were 0.38 ± 0.06, 0.22 ± 0.11 and 0.60 ± 0.21 mg L^-1, respectively. Their mass absorption cross-section at 365 nm (MAC₃₆₅) were 0.65 ± 0.16, 4.71 ± 3.68 and 1.44 ± 0.52 m² g^-1, respectively. The MAC₃₆₅ values of snowpit samples showed a significant negative correlation with DOC concentrations, indicating DOC with high MAC₃₆₅ values were likely to be kept in snow during the melting process. Topsoil samples of LHG glacierized region likely contributed a lot to snowpit DOC with high MAC₃₆₅ values due to their similar absorption spectra. Spatially, the DOC concentration of surface ice samples increased from terminus to the upper part of the glacier. Correspondingly, the MAC₃₆₅ value showed decreased trend. In the freezing experiment on surface ice and topsoil samples, small part of DOC with high MAC₃₆₅ value was also likely to enter first frozen solid phase. In addition, the radiative forcing caused by snowpit and surface ice DOC increased around 7.64 ± 2.93 and 4.95 ± 1.19 times relative to fresh snow DOC, indicating the snow/ice melting caused by increased light-absorbing DOC needs to be considered in the future research.

Extraction of lead from waste CRT funnel glass by generating lead sulfide - An approach for electronic waste management

Waste cathode ray tube (CRT) funnel glass is the key and difficult points in waste electrical and electronic equipment (WEEE) disposal. In this paper, a novel and effective process for the detoxification and reutilization of waste CRT funnel glass was developed by generating lead sulfide precipitate via a high-temperature melting process. The central function in this process was the generation of lead sulfide, which gathered at the bottom of the crucible and was then separated from the slag. Sodium carbonate was used as a flux and reaction agent, and sodium sulfide was used as a precipitating agent. The experimental results revealed that the lead sulfide recovery rate initially increased with an increase in the amount of added sodium carbonate, the amount of sodium sulfide, the temperature, and the holding time and then reached an equilibrium value. The maximum lead sulfide recovery rate was approximately 93%, at the optimum sodium carbonate level, sodium sulfide level, temperature, and holding time of 25%, 8%, 1200°C, and 2h, respectively. The glass slag can be made into sodium and potassium silicate by hydrolysis in an environmental and economical process.

Amorphous solid dispersions: Rational selection of a manufacturing process

Amorphous products and particularly amorphous solid dispersions are currently one of the most exciting areas in the pharmaceutical field. This approach presents huge potential and advantageous features concerning the overall improvement of drug bioavailability. Currently, different manufacturing processes are being developed to produce amorphous solid dispersions with suitable robustness and reproducibility, ranging from solvent evaporation to melting processes. In the present paper, laboratorial and industrial scale processes were reviewed, and guidelines for a rationale selection of manufacturing processes were proposed. This would ensure an adequate development (laboratorial scale) and production according to the good manufacturing practices (GMP) (industrial scale) of amorphous solid dispersions, with further implications on the process validations and drug development pipeline.