Electrochemical and quartz crystal microbalance detection of the cholera toxin employing horseradish peroxidase and GM1-functionalized liposomes

An ultrasensitive method for the detection of the cholera toxin (CT) using electrochemical or microgravimetric quartz crystal microbalance transduction means is described. Horseradish peroxidase (HRP) and GM1-functionalized liposomes act as catalytic recognition labels for the amplified detection of the cholera toxin based on highly specific recognition of CT by the ganglioside GM1. The sensing interface consists of monoclonal antibody against the B subunit of CT that is linked to protein G, assembled as a monolayer on an Au electrode or an Au/ quartz crystal. The CT is detected by a "sandwich-type" assay on the electronic transducers, where the toxin is first bound to the anti-CT-Ab and then to the HRP-GM1-ganglioside-functionalized liposome. The enzyme-labeled liposome mediates the oxidation of 4-chloronaphthol (2) in the presence of H2O2 to form the insoluble product 3 on the electrode support or the Au/quartz crystal. The biocatalytic precipitation of 3 provides the amplification route for the detection of the CT. Formation of the insulating film of 3 on the electrode increases the interfacial electron-transfer resistance, Ret, or enhances the electrode resistance, R', parameters that are quantitatively derived by Faradaic impedance measurements and chronopotentiometric analyses, respectively. Similarly, the precipitate 3 formed on the Au/quartz crystal results in a mass increase on the transducer that is reflected by a decrease in the resonance frequency of the crystal. The methods allow the detection of the CT with an unprecedented sensitivity that corresponds to 1.0 x 10(-13) M.

An N,N'-dialkyl-4,4'-bipyridinium-modified titanium-dioxide photocatalyst for water remediation--observation and application of supramolecular effects in photocatalytic degradation of pi-donor organic compounds

The photocatalytic activity of TiO2 (Degussa P-25) modified with a 4,4'-bipyridinium monolayer (V2+-TiO2) has been compared with that of conventional TiO2-P-25 by investigating the efficiency of degradation of a series of four organic model compounds with increasing pi-donor capacity (2,4-xylidine, 2,4-dimethylphenol, hydroquinone, and dimethylhydroquinone). As far as the mechanism of the first oxidation reaction is concerned, evidence for the formation of supramolecular donor-acceptor complexes with the bipyridinium units at the semiconductor surface was obtained by comparison of the Langmuir-adsorption characteristics and the efficiencies of photodegradation of the different substrates. Furthermore, the main intermediates of the photocatalytic degradation of 2,4-xylidine were identified, and the presence of 2,4-dimethylphenol indicates that the main pathway of substrate oxidation proceeds via electron transfer from the adsorbed organic substrate to the "holes" within the valence band of the photoexcited semiconductors V2+-TiO2 and TiO2. The efficiencies of photocatalytic degradation by both V2+-TiO2 and TiO2 were limited by the trapping efficiency of the conduction band electrons by molecular oxygen.

Nanoparticles as structural and functional units in surface-confined architectures

The nanoscale engineering of functional chemical assemblies has attracted recent research effort to provide dense information storage, miniaturized sensors, efficient energy conversion, light-harvesting, and mechanical motion. Functional nanoparticles exhibiting unique photonic, electronic and catalytic properties provide invaluable building blocks for such nanoengineered architectures. Metal nanoparticle arrays crosslinked by molecular receptor units on electrodes act as selective sensing interfaces with controlled porosity and tunable sensitivity. Photosensitizer/electron-acceptor bridged arrays of Au-nanoparticles on conductive supports act as photoelectrochemically active electrodes. Semiconductor nanoparticle composites on surfaces act as efficient light collecting systems, and nanoengineered semiconductor 'core-shell' nanocrystal assemblies reveal enhanced photoelectrochemical performance due to effective charge separation. Layered metal and semiconductor nanoparticle arrays crosslinked by nucleic acids find applications in the optical, electronic and photoelectrochemical detection of DNA. Metal and semiconductor nanoparticles assembled on DNA templates may be used to generate complex electronic circuitry. Nanoparticles incorporated in hydrogel matrices yield new composite materials with novel magnetic, optical and electronic properties.

Imprinting of chiral molecular recognition sites in thin TiO2 films associated with field-effect transistors: novel functionalized devices for chiroselective and chirospecific analyses

(R)- or (S)-2-Methylferrocene carboxylic acids, (R)-1 or (S)-1, (R)- or (S)-2-phenylbutanoic acid, (R)-2 or (S)-2, and (R)- or (S)-2-propanoic acid, (R)-3 or (S)-3, can be imprinted in thin TiO2 films on the gate surface of ion-sensitive field-effect transistor (ISFET) devices. The imprinting is performed by hydrolyzing the respective carboxylate TiIV butoxide complex on the gate surface, followed by washing off the acid from the resulting TiO2 film. The imprinted sites reveal chiroselectivity only towards the sensing of the imprinted enantiomer. The chiral recognition sites reveal not only chiroselectivity but also chirospecificity and, for example, the (R)-2-imprinted film is active in the sensing of (R)-2, but insensitive towards the sensing of (R)2-phenylpropanoic acid, (R)-3, which exhibits a similar chirality. Similarly, the (R)-3-imprinted film is inactive in the analysis of (R)-2. The chiroselectivity and chirospecificity of the resulting imprinted films are attributed to the need to align and fit the respective substrates in precise molecular contours generated in the cross-linked TiO2 films upon the imprinting process.

Lithium reduction of the bowl-shaped C60 fragment diindeno[1,2,3,4-defg;1',2',3',4'-mnop]chrysene: an interplay between experiment and calculation

Diindeno[1,2,3,4-defg;1',2',3',4'-mnop]chrysene (DIC) (one of the smallest symmetrical bowl-shaped fragments of C60) and its tetra-tert-butyl derivative are reduced with lithium metal to yield dianions and tetraanions. Due to the high degree of symmetry (C2v) of DIC and its derivative, their NMR spectra cannot be assigned using the standard two-dimensional NMR techniques. A novel carbon-edited NOESY method was used to complete the assignments of the neutral and dianion species, whereas the tetraanions are aided by DFT calculations for their assignment. Experimental charge-distribution patterns were obtained and match those of the calculations. An extension of the empirical approach for estimating the charge distribution from the 13C NMR spectra enables a direct comparison between experimentally derived charge-distribution data and the computed electron density in each of the lowest unoccupied molecular orbitals. The overall picture evolving from the orbital structure of DIC is presented and reflects the surface reactivity of C60.

Amplified detection of DNA and analysis of single-base mismatches by the catalyzed deposition of gold on Au-nanoparticles

A novel amplification route for DNA detection based on the deposition of gold on a 10 nm Au-colloid/avidin conjugate label acting as a 'seeding' catalyst, is described. Microgravimetric quartz-crystal-microbalance measurements are employed to transduce the catalyzed deposition of gold on the piezoelectric crystals. Three different DNA detection schemes are described: (i) analysis of a 27-base nucleic acid fragment; (ii) analysis of the entire M13phi DNA (7229 bases); and (iii) detection of a single-base mismatch in a DNA. Ultrasensitive detection of DNA is accomplished by the catalyzed deposition of gold, detection limit approximately 1 x 10(-15) M.

The decision-making value of magnetic resonance cholangiopancreatography in patients seen in a referral center for suspected biliary and pancreatic disease

OBJECTIVE

To assess the ability of MRCP to alter the differential diagnosis and to prevent diagnostic and/or therapeutic ERCP. The diagnostic accuracy of magnetic resonance cholangiopancreatography (MRCP) for biliary and pancreatic disease is well documented. Some believe MRCP may prevent diagnostic ERCP or add useful information, however there are no reports of its impact on clinical management.

METHODS

Consecutive patients referred for ERCP underwent clinic evaluation, then MRCP, and then ERCP. In Phase 1, the number of differential diagnoses and the perceived need for diagnostic ERCP were evaluated after each step by the endoscopist who performed the ERCP. In Phase 2, the process was repeated after presenting clinical information and MRCP results to different individual physicians: another endoscopist, a hepatologist, a radiologist, and a surgeon (all were blinded to ERCP results).

RESULTS

Forty patients were enrolled. Clinical contexts were jaundice (19.7%), abnormal liver enzymes (42.6%), abdominal pain (11.5%), recurrent acute pancreatitis (11.5%), and suspected complications of chronic pancreatitis (14.7%). In Phase 1, adding MRCP information to diagnostic ERCP information did not change the mean number of differential diagnoses significantly and prevented no therapeutic ERCP. In Phase 2, adding MRCP to clinical information only (without ERCP) reduced the differential diagnosis significantly for the radiologist and the surgeon only and would have prevented < or =3% of diagnostic and therapeutic ERCP for all physicians.

CONCLUSION

The value of MRCP information may be limited if patient selection is inappropriate and may differ in physicians depending on their speciality.

Electronic transduction of DNA sensing processes on surfaces: amplification of DNA detection and analysis of single-base mismatches by tagged liposomes

Tagged, negatively charged, liposomes are used to amplify DNA sensing processes. The analyses of the target DNA are transduced electrochemically by using Faradaic impedance spectroscopy, or by microgravimetric measurements with Au-quartz crystals. By one method, a probe oligonucleotide (1) is assembled on Au-electrodes or Au-quartz crystals. The formation of the double-stranded assembly with the analyte DNA (2) is amplified by the association of the 3-oligonucleotide-functionalized liposomes to the sensing interface. The target DNA is analyzed by this method with a sensitivity limit that corresponds to 1 x 10(-12) M. A second method to amplify the sensing of the analyte involves the interaction of the 1-functionalized electrode or Au-quartz crystal with the target DNA sample (2) that is pretreated with the biotinylated oligonucleotide (4). The formation of the three-component double-stranded assembly between 1/2/4 is amplified by the association of avidin and biotin-labeled liposomes to the sensing interfaces. By the secondary association of avidin and biotin-tagged liposomes, a dendritic-type amplification of the analysis of the DNA is accomplished. The analyte DNA (2) is sensed by this method with a sensitivity limit corresponding to 1 x 10(-13) M. The biotin-tagged liposomes are also used to probe and amplify single-base mismatches in an analyte DNA. The 6-oligonucleotide-functionalized Au-electrode or Au-quartz crystal was used to differentiate the single-base mismatch (G) in the mutant (5) from the normal A-containing gene (5a). Polymerase-induced coupling of the biotinylated-C-base to the double-stranded assembly generated between 6 and 5 followed by the association of avidin and biotin-tagged liposomes is used to probe the single base mismatch. The functionalized liposomes provide a particulate building unit for the dendritic amplification of DNA sensing.

Biomaterials integrated with electronic elements: en route to bioelectronics

Bioelectronics is a progressing interdisciplinary research field that involves the integration of biomaterials with electronic transducers, such as electrodes, field-effect-transistors or piezoelectric crystals. Surface engineering of biomaterials, such as enzymes, antigen-antibodies or DNA on the electronic supports, controls the electrical properties of the biomaterial-transducer interface and enables the electronic transduction of biorecognition events, or biocatalyzed transformation, on the transducers. Bioelectronic sensing devices, biosensors of tailored sensitivities and specificities, are being developed.

Electronically transduced molecular mechanical and information functions on surfaces

Supramolecular chemistry and nanotechnology, along with their use in the construction of functional assemblies and devices, have merged into a challenging field of study. The development of methodologies for the integration and interfacing of molecular building blocks with solid supports and electronic transducers is essential for this research. We address recent applications of molecular, macromolecular, and biomolecular substances in the organization of signal-activated, electronically transduced molecular architectures on electrode surfaces. Photonic, electronic, magnetic, and chemical stimuli are used to trigger the switchable functions of these systems, which demonstrate either mechanical (e.g., translocation) or computational (e.g., memory) functions and provide enlightening insight and directions for the future evolution of the field.

An integrated relay/nitrate reductase field-effect transistor for the sensing of nitrate (NO3-)

An integrated enzyme-functionalized field-effect transistor (ENFET) device for the sensing of nitrate ions is described. An aminosiloxane-functionalized gate interface is modified with N-methyl-N'-(carboxyalkyl)-4,4'-bipyridinium relay units. The complex formed between nitrate reductase and the bipyridinium units on the gate surface is crosslinked with glutaric dialdehyde to yield a stable relay-enzyme layer on the gate interface. In the presence of sodium dithionite as electron donor, the biocatalyzed reduction of nitrate to nitrite ion is stimulated. The ratio between the oxidized and reduced states of the bipyridinium sites regulates the gate potential, and is controlled by the concentration of NO3- ions in the system. The effect of the chain length tethering the N-methyl-N'-(carboxyalkyl)-4,4'-bipyridinium units to the gate surface on the biocatalyzed reduction of NO3- ions, and on the NO3- FET sensor performance is discussed. The devices that include the bipyridinium units tethered to the gate interface with methylene chain length, -(CH2)n, where n > or = 7, reveal a detection limit of 7 x 10(-5) M for nitrate and a sensitivity of 52 +/- 2 mV dec-1. The response time of the device is as low as 50 s, and the operational time of the system is ca. 85 s. We estimate the surface coverage of nitrate reductase on the gate surface to be ca. 1.2 x 10(-12) mol cm-2.

An integrated NAD+-dependent enzyme-functionalized field-effect transistor (ENFET) system: development of a lactate biosensor

An integrated NAD+-dependent enzyme field-effect transistor (ENFET) device for the biosensing of lactate is described. The aminosiloxane-functionalized gate interface is modified with pyrroloquinoline quinone (PQQ) that acts as a catalyst for the oxidation of NADH. Synthetic amino-derivative of NAD+ is covalently linked to the PQQ monolayer. An affinity complex formed between the NAD+/PQQ-assembly and the NAD+-cofactor-dependent lactate dehydrogenase (LDH) is crosslinked and yields an integrated biosensor ENFET-device for the analysis of lactate. Biocatalyzed oxidation of lactate generates NADH that is oxidized by PQQ in the presence of Ca2+-ions. The reduced catalyst, PQQH2, is oxidized by O2 in a process that constantly regenerates PQQ at the gate interface. The biocatalyzed formation of NADH and the O2-stimulated regeneration of PQQ yield a steady-state pH gradient between the gate interface and the bulk solution. The changes in the pH of the solution near the gate interface and, consequently, the gate potential are controlled by the substrate (lactate) concentration in the solution. The device reveals the detection limit of 1 x 10(-4) M for lactate and the sensitivity of 24+/-2 mV dec(-1). The response time of the device is as low as 15 s.

Lanthanide oxide-doped titanium dioxide photocatalysts: novel photocatalysts for the enhanced degradation of p-chlorophenoxyacetic acid

The photocatalytic degradation of p-chlorophenoxyacetic acid has been investigated in oxygenated aqueous suspensions of lanthanide oxide-doped TiO2 photocatalysts. Complete mineralization was achieved. The enhanced degradation is attributed to the formation of Lewis acid-base complex between the lanthanide ion and the substrate.

Biomaterial engineered electrodes for bioelectronics

A series of single-cysteine-containing cytochrome c, Cyt c, heme proteins including the wild-type Cyt c (from Saccharomyces cerevisiae) and the mutants (V33C, Q21C, R18C, G1C, K9C and K4C) exhibit direct electrical contact with Au-electrodes upon covalent attachment to a maleimide monolayer associated with the electrode. With the G1C-Cyt c mutant, which includes the cysteine residue in the polypeptide chain at position 1, the potential-induced switchable control of the interfacial electron transfer was observed. This heme protein includes a positively charged protein periphery that surrounds the attachment site and faces the electrode surface. Biasing of the electrode at a negative potential (-0.3 V vs. SCE) attracts the reduced Fe(II)-Cyt c heme protein to the electrode surface. Upon the application of a double-potential-step chronoamperometric signal onto the electrode, where the electrode potential is switched to +0.3 V and back to -0.3 V, the kinetics of the transient cathodic current, corresponding to the re-reduction of the Fe(III)-Cyt c, is controlled by the time interval between the oxidative and reductive potential steps. While a short time interval results in a rapid interfacial electron-transfer, ket1 = 20 s-1, long time intervals lead to a slow interfacial electron transfer to the Fe(III)-Cyt c, ket2 = 1.5 s-1. The fast interfacial electron-transfer rate-constant is attributed to the reduction of the surface-attracted Fe(III)-Cyt c. The slow interfacial electron-transfer rate constant is attributed to the electrostatic repulsion of the positively charged Cyt c from the electrode surface, resulting in long-range electron transfer exhibiting a lower rate constant. At intermediate time intervals between the oxidative and reductive steps, two populations of Cyt c, consisting of surface-attracted and surface-repelled heme proteins, are observed. Crosslinking of a layered affinity complex between the Cyt c and cytochrome oxidase, COx, on an Au-electrode yields an electrically-contacted, integrated, electrode for the four-electron reduction of O2 to water. Kinetic analysis reveals that the rate-limiting step in the bioelectrocatalytic reduction of O2 by the integrated Cyt c/COx electrode is the primary electron transfer from the electrode support to the Cyt c units.

Detection of single-base DNA mutations by enzyme-amplified electronic transduction

Here we describe a method for the sensitive detection of a single-base mutation in DNA. We assembled a primer thiolated oligonucleotide, complementary to the target DNA as far as one base before the mutation site, on an electrode or a gold-quartz piezoelectric crystal. After hybridizing the target DNA, normal or mutant, with the sensing oligonucleotide, the resulting assembly is reacted with the biotinylated nucleotide, complementary to the mutation site, in the presence of polymerase. The labeled nucleotide is coupled only to the double-stranded assembly that includes the mutant site. Subsequent binding of avidin-alkaline phosphatase to the assembly, and the biocatalyzed precipitation of an insoluble product on the transducer, provides a means to confirm and amplify detection of the mutant. Faradaic impedance spectroscopy and microgravimetric quartz-crystal microbalance analyses were employed for electronic detection of single-base mutants. The lower limit of sensitivity for the detection of the mutant DNA is 1 x 10-14 mol/ml. We applied the method for the analysis of polymorphic blood samples that include the Tay-Sachs genetic disorder. The sensitivity of the method enables the quantitative analysis of the mutant with no PCR pre-amplification.

Tailored chemosensors for chloroaromatic acids using molecular imprinted TiO2 thin films on ion-sensitive field-effect transistors

The SiO2 gate of an ion-sensitive field-effect transistor, (ISFET), is functionalized with a TiO2 film that includes imprinted molecular sites for 4-chlorophenoxy acetic acid, (1), or 2,4-dichlorophenoxy acetic acid, (2). The functionalized devices that include the imprinted interfaces reveal an impressive selectivity in the sensing of the imprinted substrates Na+ -1 or Na+ -2. The detection limit for Na+ -1 is (5+/-2) x 10(-4) M, which corresponds to 38 mV x dec(-1) in the concentration range of 0.5 to 6 mM. The detection limit for the analysis of Na+ -2 is (1.0+/-0.2) x 10(-5) M, which corresponds to 28 mV dec(-1) in the concentration range 0.1-9.0 mM. The equilibration time of the devices is ca. 5 min.

Liposomes labeled with biotin and horseradish peroxidase: a probe for the enhanced amplification of antigen--antibody or oligonucleotide--DNA sensing processes by the precipitation of an insoluble product on electrodes

Liposomes labeled with biotin and the enzyme horseradish peroxidase (HRP) are used as a probe to amplify the sensing of antigen-antibody interactions or oligonucleotide-DNA binding. The HRP-biocatalyzed oxidation of 4-chloro-1-naphthol (1) in the presence of H2O2, and the precipitation of the insoluble product 2 on electrode supports, are used as an amplification route for the sensing processes. The anti-dinitrophenyl antibody (DNP-Ab) is sensed by a dinitrophenyl-L-cysteine antigen monolayer associated with an Au electrode. A biotinylated anti-IgG-antibody (Fc-specific) is linked to the antigen-DNP-Ab complex, and the biotin-labeled HRP-liposomes associate with the assembly through an avidin bridge. The biocatalyzed precipitation of 2 on the electrode increases the electron-transfer resistances at the electrode-solution interface or the electrode resistance itself. The binding events of the different proteins on the electrode and the biocatalyzed precipitation of 2 on the conductive support are followed by Faradaic impedance spectroscopy or constant-current chronopotentiometry. DNP-Ab concentrations as low as 1 x 10(-11) g x mL(-1) can be detected by this method. The labeled liposomes were also used for the amplified detection of DNA 3. The oligonucleotide 4, complementary to a part of the target DNA 3 that is a model nucleic acid sequence for the Tay-Sachs genetic disorder, is assembled on an Au electrode. Hybridization of the analyte 3 followed by the association of the biotin-tagged oligonucleotide 5 yields a three-component double-stranded assembly. Sensing of the analyte 3 is amplified by the association of avidin, the labeled liposomes, and the subsequent biocatalyzed precipitation of 2 on the electrodes. The DNA 3 is detected with a sensitivity that corresponds to 6.5 x 10(-13) M. Faradaic impedance spectroscopy and chronopotentiometry were employed to follow the stepwise assembly of the systems and the electronic transduction of the detection of the analyte DNA 3.

Nanoparticle arrays on surfaces for electronic, optical, and sensor applications

Particles in the nanometer size range are attracting increasing attention with the growth of interest in nanotechnological disciplines. Nanoparticles display fascinating electronic and optical properties as a consequence of their dimensions and they may be easily synthesized from a wide range of materials. The dimensions of these particles makes them ideal candidates for the nanoengineering of surfaces and the fabrication of functional nanostructures. In the last five years, much effort has been expended on their organization on surfaces for the construction of functional interfaces. In this review, we address the research that has led to numerous sensing, electronic, optoelectronic, and photoelectronic interfaces, and also take time to cover the synthesis and characterization of nanoparticles and nanoparticle arrays.

Integration of Layered Redox Proteins and Conductive Supports for Bioelectronic Applications

Integration of redox enzymes with an electrode support and formation of an electrical contact between the biocatalysts and the electrode is the fundamental subject of bioelectronics and optobioelectronics. This review addresses the recent advances and the scientific progress in electrically contacted, layered enzyme electrodes, and discusses the future applications of the systems in various bioelectronic devices, for example, amperometric biosensors, sensoric arrays, logic gates, and optical memories. This review presents the methods for the immobilization of redox enzymes on electrodes and discusses the covalent linkage of proteins, the use of supramolecular affinity complexes, and the reconstitution of apo-redox enzymes for the nanoengineering of electrodes with protein monolayers of electrodes with protein monolayers and multilayers. Electrical contact in the layered enzyme electrode is achieved by the application of diffusional electron mediators, such as ferrocene derivatives, ferricyanide, quinones, and bipyridinium salts. Covalent tethering of electron relay units to layered enzyme electrodes, the cross-linking of affinity complexes formed between redox proteins and electrodes functionalized with relay-cofactor units, or surface reconstitution of apo-enzymes on relay-cofactor-functionalized electrodes yield bioelectrocatalytic electrodes. The application of the functionalized electrodes as biosensor devices is addressed and further application of electrically "wired" enzymes as catalytic interfaces in biofuel cells is discussed. The organization of sensor arrays, self-calibrated biosensors, or gated bioelectronic devices requires the microstructuring of biomaterials on solid supports in the form of ordered micro-patterns. For example, light-sensitive layers composed of azides, benzophenone, or diazine derivatives associated with solid supports can be irradiated through masks to enable the patterned covalent linkage of biomaterials to surfaces. Alternatively, patterning of biomaterials can be accomplished by noncovalent interactions (such as in affinity complexes between avidin and a photolabeled biotin, or between an antibody and a photoisomerizable antigen layer) to provide a means of organizing protein microstructures on surfaces. The organization of patterned hydrophilic/hydrophobic domains on surfaces, by using photolithography, stamping, or micromachining methods, allows the selective patterning of surfaces by hydrophobic, noncovalent interactions. Photoactivated layered enzyme electrodes act as light-switchable optobioelectronic systems for the amperometric transduction of recorded photonic information. These systems can act as optical memories, biomolecular amplifiers, or logic gates. The photoswitchable enzyme electrodes are generated by the tethering of photoisomerizable groups to the protein, the reconstitution of apo-enzymes with semisynthetic photoisomerizable cofactor units, or the coupling of photoisomerizable electron relay units.

Sensing of acetylcholine by a tricomponent-enzyme layered electrode using faradaic impedance spectroscopy, cyclic voltammetry, and microgravimetric quartz crystal microbalance transduction methods

A three-enzyme layered assembly on Au electrodes or Au-quartz crystals, consisting of horseradish peroxidase, HRP, choline oxidase, ChO, and acetylcholine esterase, AChE, is used to sense acetylcholine by the HRP-mediated oxidation of 3,3',5,5'-tetramethylbenzidine, TMB (1), by H2O2, and the formation of the insoluble product (2) on the respective transducers. The analyte-substrate, acetylcholine, is hydrolyzed by AChE to choline that is oxidized by ChO and O2 to yield the respective betaine and H2O2. The amounts of generated H2O2 and the resulting insoluble product on the transducers correlate with the concentration of acetylcholine in the samples. The formation of the insoluble product (2) on electrode supports is followed by faradaic impedance spectroscopy that probes the increased interfacial electron-transfer resistance upon the formation of 2, and by cyclic voltammetry that reflects electron-transfer barriers upon the formation of the precipitate. The frequency of the Au-quartz crystal decreases as a result of the accumulation of the insoluble precipitate. The amount of insoluble product formed on the transducers is controlled by the concentration of acetylcholine and by the time interval of biocatalyzed precipitation. The generation of the insoluble product provides a means to amplify the sensing processes. Acetylcholine concentrations corresponding to 1 x 10(-5) M are easily sensed by the different transducers.

An Au nanoparticle/bisbipyridinium cyclophane-functionalized ion-sensitive field-effect transistor for the sensing of adrenaline

A film consisting of polyethyleneimine (PEI), Au nanoparticles (12 +/- 1 nm) and coadsorbed cyclobis(paraquat-p-phenylene) (1) was assembled as a sensing interface on the Al2O3 insulating layer of an ion-sensitive field-effect transistor (ISFET). Adrenaline (2) was sensed by the functionalized ISFET with a detection limit of 1 x 10(-6) M. The sensing ability of the nanostructured device for the analysis of adrenaline originates from the preconcentration of the analyte in the cyclophane by pi-pi donor-acceptor interactions. Analysis of adrenaline is accomplished by the measurement of the source-drain current, Isd, or by the gate-source voltage, Vgs. The sensing device is reusable (at least 100 cycles) and exhibits high stability.

Precipitation of an insoluble product on enzyme monolayer electrodes for biosensor applications: characterization by Faradaic impedance spectroscopy, cyclic voltammetry, and microgravimetric quartz crystal microbalance analyses

Precipitation of an insoluble, insulating product on monolayer-functionalized electrodes enables the development of new electrochemical biosensors. Faradaic impedance spectroscopy and cyclic voltammetry are used to probe the electron-transfer resistance at the conductive support upon the accumulation of the insoluble product on the electrode surface. Similarly, microgravimetric quartz crystal microbalance, QCM, analyses were used to assay the formation of the precipitate on the electrode. A horseradish peroxidase, HRP, monolayer electrode is used to analyze H2O2 via the biocatalyzed oxidation of 4-chloro-1-naphthol (1) and the precipitation of the insoluble product (2). A bienzyme-layered electrode consisting of HRP and glucose oxidase, GOx, is used to sense glucose. Biocatalyzed oxidation of glucose by O2, in the presence of GOx, yields H2O2, and the generated hydrogen peroxide effects the formation of the insoluble product (2) in the presence of HRP. The insoluble product accumulated on the electrode, and the extent of the resulting electron-transfer resistance, correlated with the amounts of H2O2 or glucose, and appropriate calibration curves are extracted.