Ceramic abutments and ceramic oral implants. An update

Fracture resistance of a second generation of zirconia implants after artificial ageing: An in vitro study

OBJECTIVES

The aim of this study was to determine the bending moments of a further developed generation of a one-piece zirconia implant system, which, for example, has a reduced diameter in the neck area compared to the predecessor model.

METHODS

A total of 48 one-piece ceramic implants with diameters of 3.6 mm and 4.1 mm were included. After preparation of the abutments of 50% of the implants, 32 out of the 48 implants were subjected to artificial ageing in a chewing simulator (Force: 98 N; 1.2 or 5 million loading cycles; thermocyclicing: 5°C / 55°C). The implants were then subjected to static loading until fracture in order to determine the maximum load forces to calculate the bending moments.

RESULTS

Implants tested after 1.2 million loading cycles exhibited the highest bending moments (3.6 mm diameter without abutment preparation: 496.1 ± 50.6 Ncm; 3.6 mm diameter with abutment preparation: 507.9 ± 53.5 Ncm; 4.1 mm diameter without abutment preparation: 612.5 ± 49.0 Ncm; 4.1 mm diameter with abutment preparation: 656.9 ± 26.8 Ncm). In contrast, unloaded implants showed the lowest values (3.6 mm diameter without abutment preparation: 443.0 ± 38.6 Ncm; 3.6 mm diameter with abutment preparation: 436.1 ± 42.8 Ncm; 4.1 mm diameter without abutment preparation: 570.3 ± 64.8 Ncm; 4.1 mm diameter with abutment preparation: 560.9 ± 51.5 Ncm), while implants subjected to 5 million cycles of loading showed bending moment values between these two groups.

CONCLUSIONS

Within the limits of the present study, preparation of the abutment did not appear to have a negative effect on stability. Also, artificial ageing did not seem to have a negative effect on the fracture resistance; a possible negative effect on the bending moment would have to be investigated with more than 5 million loading cycles. The measured maximum fracture loads were generally higher than the masticatory forces described in the literature.

CLINICAL SIGNIFICANCE

The investigated zirconia implants seem to be a viable alternative to titanium implants.

Implant Surface Decontamination Methods That Can Impact Implant Wettability

This review addresses the effects of various decontamination methods on the wettability of titanium and zirconia dental implants. Despite extensive research on surface wettability, there is still a significant gap in understanding how different decontamination techniques impact the inherent wettability of these surfaces. Although the literature presents inconsistent findings on the efficacy of decontamination methods such as lasers, air-polishing, UV light, and chemical treatments, the reviewed studies suggest that decontamination alters in vitro hydrophilicity. Post-decontamination surface chemistry must be carefully considered when selecting optimal surface treatments for implant materials. Further in vitro investigations are essential to determine which approaches best enhance surface wettability, potentially leading to improved implant-tissue interactions in clinical settings.

Peri-implantitis induction and resolution around zirconia versus titanium implants

BACKGROUND

This study compared titanium and zirconia implant ligature-induced peri-implant defect progression and response to regenerative surgical intervention.

METHODS

Eight tissue-level endosseous implants were placed in 6 mixed-breed foxhounds, with 2 zirconia and 2 titanium alternating in each hemimandible. Cotton ligatures were placed subgingivally for 16 weeks followed by 8 weeks of spontaneous progression. Standardized radiographs were captured every 2 weeks to evaluate the rate of bone loss. Regenerative surgery was performed utilizing water-jet decontamination, enamel matrix derivative, and locally harvested autogenous bone. After 16 weeks of healing, final radiographic bone levels as well as probing depths, recession, and clinical attachment levels were assessed.

RESULTS

All 48 implants integrated successfully. The final average post-ligature radiographic defects were 2.88 and 3.05 mm for titanium and zirconia implants, respectively. There was no significant difference between materials in the rate of radiographic bone loss (p = 0.09). Following regenerative surgery, the total average amount of radiographic bone gain was 1.41 and 1.20 mm for titanium and zirconia, respectively. The percentage of defect fill was 51.56% and 37.98% (p = 0.03) for titanium and zirconia, respectively. Inter-group differences were minimal for clinical parameters at the time of sacrifice including periodontal pocket depths (p = 0.81), recession (p = 0.98), or clinical attachment levels (p = 0.51).

CONCLUSIONS

No significant difference was found in the rate of peri-implant defect development between titanium and zirconia implants. Both materials gained significant radiographic bone following regenerative surgery with significantly greater defect percentage fill in titanium implants. The final clinical parameters were similar in both groups.

The effect of different abutment and restorative crown materials on stress distribution in single-unit implant-supported restorations: A 3D finite element stress analysis

PURPOSE

To evaluate the effect of restorative materials with or without resin content, modeled on zirconia and titanium abutment materials, on the stress distribution on the alveolar bone, implant, and prosthetic crowns with a 3D finite element stress analysis.

MATERIAL AND METHODS

Titanium and zirconia abutments were combined with three implant-supported crown materials (polymer infiltrated hybrid ceramic (PICN), lithium disilicate (LD), and zirconia-reinforced lithium silicate (ZLS)) to create six experimental groups. The 40 × 30 × 20 mm alveolar bone, 3.75 × 10 mm implant, esthetic abutment, and maxillary first premolar crown bonded over the abutment were the components of the finite element models. On the lingual cusp of the crown, the 150 N occlusal loading was applied in the buccolingual direction at a 30° angle. Equivalent von Mises stress and maximum and minimum principal stresses were used for both the qualitative and quantitative evaluation of the stress distribution of the created models.

RESULTS

The von Mises stress in implant and abutment did not differ according to the crown materials. The use of a zirconia abutment resulted in higher von Mises stress values in the abutment but lower stress values in the implant. The highest stress values were obtained in ZLS (196.65 MPa) and LD (194.05 MPa) crowns. The use of titanium abutments, regardless of crown materials, resulted in higher von Mises stress values in restorative crowns than in zirconia abutments. The principal stress values in alveolar bone showed similar distribution and concentration in all models.

CONCLUSIONS

Changes in crown material did not affect stress distribution in the implant and peripheral bone. However, the zirconia esthetic abutment resulted in a lower stress concentration on the implant.

Strength-limiting damage and defects of dental CAD/CAM full-contour zirconia ceramics

OBJECTIVE

This study aimed to compare the four-point flexural strength of CAM-milled and sintered (as-sintered, AS) specimens with those of high-polished (HP) specimens using chairside polishing systems to simulate clinical surface conditions.

METHODS

Seven full-contour zirconia CAM/CAM blanks with various yttria contents (3, 4, 5 mol%) including three high-translucent groups (5Y) were selected to prepare flexural specimens. The bend bar specimens (2.0 × 4.0 × 25.0 mm3) were fabricated by using STL file and dental CAM machine with the respective zirconia blanks (98 mm ϕ and 10-14 mm in height). Twelve bar specimens were machined from one zirconia puck and a total of 24 specimens were prepared from each group. The pre-sintered bar specimens were sintered by using a dental zirconia furnace at 1530-1550 °C for 2 h according to the instructions. All sintered specimens were divided into two groups: as-sintered (AS) group and high-polished (HP) groups (n = 12). HP groups were subjected to polishing one surface of specimens using a three-step polishing system and finally finished with diamond polishing. After cleaning and drying, the flexural strength of all specimens was determined by a fully articulating four-point flexure fixture consisting of a 1/4-point test configuration with an inner/outer span of 10/20 mm. Statistical differences between AS and HP groups were conducted with Weibull analysis. The fractured surfaces of zirconia specimens were observed using a field emission SEM and EDS to detect failure origins.

RESULTS

The mean AS flexural strength values were significantly lower than those of HP counterparts. However, Weibull moduli expressing the reliability of HP groups were generally decreased although not significantly in comparison to their AS. The fracture of the AS specimens mostly originated from extrinsic CAM-milling defects, while the HP specimens were fractured from intrinsic subsurface or volume defects including pores, large grain clusters, inclusions, and corner-located critical flaws. Two high-translucent (5Y) zirconia groups were not affected in their strength and reliability after polishing, whereas one 5Y zirconia significantly increased its strength but significantly lowered its reliability.

SIGNIFICANCE

The extrinsic and intrinsic strength-limiting defects should be considered in evaluating the flexural strength and reliability of dental CAD/CAM zirconia ceramics for full-contour restorations. For the materials tested in this study, more optimized processing of blanks and milling protocols of pre-sintered zirconia blanks should be developed including post-sintering surface finishing to reduce the flaw population regulating strength and reliability which will affect the survivability of dental zirconia prostheses.

Are Allergy-Induced Implant Failures Actually Hypersensitivity Reactions to Titanium? A Literature Review

PURPOSE

This literature review was performed to assess whether implant failures are associated with titanium allergy.

MATERIALS AND METHODS

An electronic search of the MEDLINE/PubMed, Cochrane Library, and Scopus databases up to April 2021 was conducted, and the obtained articles were independently assessed by two reviewers. Articles describing cases of implant failure in which the cause of implant failure was only identified as allergy were included.

RESULTS

Twelve studies were included. Eight studies identified Ti allergy by clinical examinations, of which four used patch tests, three used the lymphocyte transformation test (LTT)/memory lymphocyte immunostimulation assay (MELISA), and one used both tests. Nine studies reported cases of titanium hypersensitivity in combination with other systemic allergy-related disorders, with eight cases also showing positive results for Ni, Hg, Cr, and Co hypersensitivity. Ten papers reported the improvement of symptoms after the removal of the Ti implants and their replacement with zirconia implants, and two of these papers showed good results.

CONCLUSION

Cases of probable titanium allergy included those with true titanium allergies and those with a potentially different cause. However, the differentiation of these cases is difficult. Since no definitive method has been established for diagnosing titanium allergy, a comprehensive diagnosis based on the clinical course and clinical examination using a patch test/LTT/MELISA is necessary. Implant treatment should be performed with caution in patients with any preoperative allergies.

Biomaterials and Clinical Application of Dental Implants in Relation to Bone Density-A Narrative Review

Titanium has been the material of choice for dental implant fixtures due to its exceptional qualities, such as its excellent balance of rigidity and stiffness. Since zirconia is a soft-tissue-friendly material and caters to esthetic demands, it is an alternative to titanium for use in implants. Nevertheless, bone density plays a vital role in determining the material and design of implants. Compromised bone density leads to both early and late implant failures due to a lack of implant stability. Therefore, this narrative review aims to investigate the influence of implant material/design and surgical technique on bone density from both biomechanical and biological standpoints. Relevant articles were included for analysis. Dental implant materials can be fabricated from titanium, zirconia, and PEEK. In terms of mechanical and biological aspects, titanium is still the gold standard for dental implant materials. Additionally, the macro- and microgeometry of dental implants play a role in determining and planning the appropriate treatment because it can enhance the mechanical stress transmitted to the bone tissue. Under low-density conditions, a conical titanium implant design, longer length, large diameter, reverse buttress with self-tapping, small thread pitch, and deep thread depth are recommended. Implant material, implant design, surgical techniques, and bone density are pivotal factors affecting the success rates of dental implant placement in low-density bone. Further study is required to find the optimal implant material for a clinical setting's bone state.

Copper-containing nanoparticles: Mechanism of antimicrobial effect and application in dentistry-a narrative review

Copper has been used as an antimicrobial agent long time ago. Nowadays, copper-containing nanoparticles (NPs) with antimicrobial properties have been widely used in all aspects of our daily life. Copper-containing NPs may also be incorporated or coated on the surface of dental materials to inhibit oral pathogenic microorganisms. This review aims to detail copper-containing NPs' antimicrobial mechanism, cytotoxic effect and their application in dentistry.

Advancing dental implants: Bioactive and therapeutic modifications of zirconia

Zirconium-based implants have gained popularity in the dental implant field owing to their corrosion resistance and biocompatibility, attributed to the formation of a native zirconia (ZrO₂) film. However, enhanced bioactivity and local therapy from such implants are desirable to enable the earlier establishment and improved long-term maintenance of implant integration, especially in compromised patient conditions. As a result, surface modification of zirconium-based implants have been performed using various physical, chemical and biological techniques at the macro-, micro-, and nano-scales. In this extensive review, we discuss and detail the development of Zr implants covering the spectrum from past and present advancements to future perspectives, arriving at the next generation of highly bioactive and therapeutic nano-engineered Zr-based implants. The review provides in-depth knowledge of the bioactive/therapeutic value of surface modification of Zr implants in dental implant applications focusing on clinical translation.

Ceramic Toughening Strategies for Biomedical Applications

Aiming at shortage of metal materials, ceramic is increasingly applied in biomedicine due to its high strength, pleasing esthetics and good biocompatibility, especially for dental restorations and implants, artificial joints, as well as synthetic bone substitutes. However, the inherent brittleness of ceramic could lead to serious complications, such as fracture and disfunction of biomedical devices, which impede their clinical applications. Herein, several toughening strategies have been summarized in this review, including reinforcing phase addition, surface modification, and manufacturing processes improvement. Doping metal and/or non-metal reinforcing fillers modifies toughness of bulk ceramic, while surface modifications, mainly coating, chemical and thermal methods, regulate toughness on the surface layer. During fabrication, optimization should be practiced in powder preparation, green forming and densification processes. Various toughening strategies utilize mechanisms involving fine-grained, stress-induced phase transformation, and microcrack toughening, as well as crack deflection, bifurcation, bridging and pull-out. This review hopes to shed light on systematic combination of different toughening strategies and mechanisms to drive progress in biomedical devices.

Management and prevention of soft tissue complications in implant dentistry

The management and prevention of soft tissue complications is of key importance in modern implant dentistry and influences biologic and esthetic outcomes. The assessment of the soft tissue conditions from a quantitative and qualitative perspective should, therefore, be part of the overall treatment plan. Such an assessment dictates a potential indication as well as an ideal time point for additional soft tissue management. A proper risk assessment and management of the soft tissues at the planned implant site are of key importance prior to any implant‐related surgery. Cases with peri‐implant soft tissue complications generally involve: (a) a lack of attached and keratinized mucosa; (b) insufficient volume; (c) development of mucosal dehiscences; or (d) a combination of (a), (b), and (c). In case of soft tissue deficiencies, these should be addressed as early as possible to increase the predictability of the surgical interventions. This article reviews the main causes for peri‐implant soft tissue complications and presents different therapeutic options for the management of various clinical scenarios.

Clinical and radiographic success of injection-molded 2-piece zirconia implants submitted to immediate loading: A 12-month report of two cases

This case report describes the treatment of two patients who presented with single edentulous sites in the region of upper premolars and were rehabilitated through the placement of injection-molded 2-piece zirconia implants and immediate single crowns. Three months after surgery, definitive prostheses were confectioned through digital workflow. Both patients were followed for 12 months during which clinical and radiographic implant success were observed, concerning implant stability, absence of peri-implantitis signs, complete implant osseointegration, good marginal bone-level maintenance, and excellent soft tissue esthetics. No biological or mechanical complications were observed within this period.

Effect of anodized titanium abutment collars on peri-implant soft tissue: A split-mouth clinical study

STATEMENT OF PROBLEM

Anodic oxidation of titanium implant abutment collars has been used to mask their unesthetic grayish color. However, the effect of anodic oxidation on the health and appearance of peri-implant soft tissues is unclear.

PURPOSE

The purpose of this split-mouth clinical study was to investigate the effect of anodized titanium on the health and esthetics of peri-implant soft tissues.

MATERIAL AND METHODS

A total of 60 osseointegrated implants placed in 30 participants were included in the present study. Each participant received 2 randomly allocated abutments, one with a pink anodized collar and the other with an unanodized one to form 2 groups: unanodized group (control group) and anodized group (experimental group). All implants were restored with lithium disilicate restorations. Evaluations of the peri-implant soft tissues were performed at the time of definitive restoration insertion (baseline) and after 3, 6, 12, and 18 months: peri-implant probing depth, soft tissue recession, modified sulcus bleeding index, modified plaque index, and modified gingival index. The esthetics of peri-implant soft tissues were evaluated by using the modified pink esthetic score. The paired t test or Wilcoxon signed-rank test was used for comparing the 2 study groups at each point of time depending on the normality of the variables (α=.05). To compare each variable at different time points within each group separately, repeated measures ANOVA or Friedman tests were used according to the normality of the variables, followed by post hoc pairwise comparisons by using the Bonferroni adjusted significance (α=.05).

RESULTS

Five peri-implant soft tissue indices were followed up throughout the study. No statistically significant differences were found among the mean values of the tested indices in the anodized and unanodized groups throughout the evaluation periods (P>.05). The collective mean values of the modified pink esthetic score also showed no statistically significant differences between the groups (P>.05).

CONCLUSIONS

Based on this split-mouth clinical study, pink anodized titanium abutment collars do not produce a clinically significant effect on the health or esthetics of peri-implant soft tissues.

Comparison of zirconia degradation in dental implants and femoral balls: an X-ray diffraction and nanoindentation study

Background

New tetragonal zirconia polycrystal dental implants stabilized with yttria (Y-TZP) have appeared in the implantology market in the form of single piece or two-piece zircona implant system. These new type of implants improve the aesthetical properties compared to conventional commercially pure (c.p.) titanium used for implants, although the long term mechanical behavior of these new implants is not yet well known. In orthopaedics, the application of zirconia as femoral balls presented an important controversial use due to the premature fracture once implanted. Y-TZP dental implants can be affected by hydrothermal degradation and its behavior should be analysed to avoid a premature fracture. The scientific question behind the study is to analyse if the degradation mechanism observed in orthopaedics applications of Y-TZP is similar to that of Y-TZP for dental applications.

Materials and methods

For this purpose, 30 original Y-TZP dental implants and 42 Y-TZP femoral balls fractured in vivo have been studied. Dental implants were submitted to an accelerated hydrothermal degradation to compare with the femoral balls fractured in vivo. Phase transformation as well as the mechanical behaviour of the degraded samples was studied by X ray diffraction and nanoindentation tests, respectively.

Results

Results have shown that the fracture mechanism of dental implants does not resemble the mechanism observed in orthopaedic samples, presenting a good long-term behaviour.

Conclusion

The results ensure the good performance of zirconia dental implants, because the degradation of the ceramic is very limited and does not affect the mechanical properties.

Surface Modifications for Zirconia Dental Implants: A Review

Zirconia-based bioceramic is a potential material for dental implants developed and introduced in dentistry 30 years ago. However, some limitations still exist for zirconia implants caused by several factors, such as manufacturing difficulties, low-temperature degradation (LTD), long-term stability, and clinical experience. Several studies validated that some subtle changes on the zirconia surface might significantly impact its mechanical properties and osseointegration. Thus, attention was paid to the effect of surface modification of zirconia implants. This review generally summarizes the surface modifications of zirconia implants to date classified as physical treatment, chemical treatment, and surface coating, aiming to give an overall perspective based on the current situation. In conclusion, surface modification is an effective and essential method for zirconia implant application. However, before clinical use, we need more knowledge about these modification methods.

Adhesion of Resin-Resin and Resin-Lithium Disilicate Ceramic: A Methodological Assessment

The aim of this study was to evaluate four test methods on the adhesion of resin composite to resin composite, and resin composite to glass ceramic. Resin composite specimens (N = 180, Quadrant Universal LC) were obtained and distributed randomly to test the adhesion of resin composite material and to ceramic materials (IPS e.max CAD) using one of the four following tests: (a) Macroshear SBT: (n = 30), (b) macrotensile TBT: (n = 30), (c) microshear µSBT: (n = 30) and (d) microtensile µTBT test (n = 6, composite-composite:216 sticks, ceramic-composite:216 sticks). Bonded specimens were stored for 24 h at 23 °C. Bond strength values were measured using a universal testing machine (1 mm/min), and failure types were analysed after debonding. Data were analysed using Univariate and Tukey’s, Bonneferroni post hoc test (α = 0.05). Two-parameter Weibull modulus, scale (m), and shape (₀) were calculated. Test method and substrate type significantly affected the bond strength results, as well as their interaction term (p < 0.05). Resin composite to resin composite adhesion using SBT (24.4 ± 5)^a, TBT (16.1 ± 4.4)^b and µSBT (20.6 ± 7.4)^a,b test methods presented significantly lower mean bond values (MPa), compared to µTBT (36.7 ± 8.9)^b (p < 0.05). When testing adhesion of glass ceramics to resin composite, µSBT (6.6 ± 1)^B showed the lowest and µTBT (24.8 ± 7)^C,D the highest test values (MPa) (SBT (14.6 ± 5)^A,D and TBT (19.9 ± 5)^A,B) (p < 0.05). Resin composite adhesion to ceramic vs. resin composite did show significant difference for the test methods SBT and µTBT (resin composite (24.4 ± 5; 36.7 ± 9 MPa) vs. glass ceramic (14.6 ± 5; 25 ± 7 MPa)) (p > 0.05). Among substrate–test combinations, Weibull distribution presented the highest shape values for ceramic–resin in µSBT (7.6) and resin–resin in µSBT (5.7). Cohesive failures in resin–resin bond were most frequently observed in SBT (87%), followed by TBT (50%) and µSBT (50%), while mixed failures occurred mostly in ceramic–resin bonds in the SBT (100%), TBT (90%), and µSBT (90%) test types. According to Weibull modulus, failure types, and bond strength, µTBT tests might be more reliable for testing resin-based composites adhesion to resin, while µSBT might be more suitable for adhesion testing of resin-based composites to ceramic materials.

Masking of High-Translucency Zirconia for Various Cores

CLINICAL RELEVANCE

Various core materials with different shades affect the final color of high-translucency monolithic zirconia restorations. The blue core shows the greatest color difference in final zirconia restorations followed by metal, A3 dentin-shade resin core, and white core.

SUMMARY

The purpose of this study was to evaluate the masking ability of high-translucency monolithic zirconia for various core materials. A computer-aided design-computer-aided manufacturing system was used to design a zirconia disc with a diameter of 10 mm and a thickness of 1.0 mm. Four groups of cores (n=15 each) were fabricated with blue-colored dual-cure resin, white-colored dual-cure resin, A3 dentin-shade composite resin, and titanium block with 10-mm diameter and 5-mm thickness.Dual-cure, self-adhesive resin cement discs with a thickness of 25.0 ± 0.02 μm were fabricated. The color was measured using a handheld spectrophotometer. Color measurements of all specimens were performed on a white background. To assess the masking ability of zirconia, the difference between the values measured with zirconia on a white background and the values measured with zirconia on each of the four types of core material as a background with the cement specimens interposed (zirconia + cement + core) was determined. To enhance the optical connection between the specimens, distilled water was applied between each layer during each measurement.The results showed that the value of ΔE was highest for the blue core followed by metal, A3 dentin-shade resin core, and white-resin core. No significant differences were observed between the metal core and the A3 dentin-shade resin core or between the A3 dentin-shade resin core and the white core. The blue core had the significantly highest ΔE value based on Tukey's honest significant difference test.Different core materials affect the final color of high-translucency monolithic zirconia restorations. Thus, our study showed that the final color of high-translucency monolithic zirconia restorations could be affected by the type of core material used.

Fracture strength analysis of titanium insert-reinforced zirconia abutments according to the axial height of the titanium insert with an internal connection

This study aimed to analyze fracture strength in vitro by varying the axial height of the titanium insert and the labial height of the zirconia abutment in an internal connection implant to identify the titanium insert axial height with optimal mechanical stability. Sixty implants with an internal connection system were used. Two-piece zirconia abutments were used with the titanium inserts. Combinations of different titanium insert axial heights (mm) and zirconia abutment labial heights (mm) constituted five groups: Gr1 (1–3), Gr2 (3–3), Gr3 (3–5), Gr4 (5–3), and Gr5 (5–5). After thermocycling, a fracture load test was performed with a universal testing machine. The initial deformation load and the fracture load were measured and analyzed. The fractured surface and cross-section of the specimens were examined by scanning electron microscopy (SEM). The groups of titanium inserts with axial heights of 3 mm and 5 mm showed significantly greater initial deformation load and fracture load than the group with an axial height of 1 mm (p < 0.05), but there was no significant difference between the two groups with axial heights of 3 mm and 5 mm. The labial height of the zirconia abutment had no significant influence on the initial deformation load and fracture load. In some specimens in Gr4 and Gr5, cracking or bending of the titanium insert and abutment screw was observed on SEM. The axial height of the titanium insert should be designed to not be less than 3 mm to increase the fracture strength and promote the long-term stability of implants.

Quercetin-Based Nanocomposites as a Tool to Improve Dental Disease Management

The restoration and prosthetic rehabilitation of missing teeth are commonly performed using dental implants, which are extremely effective and long-lasting techniques due to their osteointegration ability with the preimplant tissues. Quercetin is a phytoestrogen-like flavonoid well known for its several positive effects on human health, mostly linked to the anti-inflammatory, antioxidant, and antibacterial activities against both Gram-positive and Gram-negative bacteria. Moreover, many studies in dentistry and the maxillofacial fields have highlighted the positive effects of quercetin on osteogenesis, acting on osteoblast activity and angiogenetic process, and promoting soft and hard tissue regeneration. This review focuses on the role of quercetin on the healing and restoration of bony defects, considering the experimental findings of its application both in vitro and in vivo as a mere compound or in association with scaffolds and dental implants having functionalized surfaces.

Off-Stoichiometric Reactions at the Cell-Substrate Biomolecular Interface of Biomaterials: In Situ and Ex Situ Monitoring of Cell Proliferation, Differentiation, and Bone Tissue Formation

The availability of osteoinductive biomaterials has encouraged new therapies in bone regeneration and has potentially triggered paradigmatic shifts in the development of new implants in orthopedics and dentistry. Among several available synthetic biomaterials, bioceramics have gained attention for their ability to induce mesenchymal cell differentiation and successive bone formation when implanted in the human body. However, there is currently a lack of understanding regarding the fundamental biochemical mechanisms by which these materials can induce bone formation. Phenomenological studies of retrievals have clarified the final effect of bone formation, but have left the chemical interactions at the cell-material interface uncharted. Accordingly, the knowledge of the intrinsic material properties relevant for osteoblastogenesis and osteoinduction remains incomplete. Here, we systematically monitored in vitro the chemistry of mesenchymal cell metabolism and the ionic exchanges during osteoblastogenesis on selected substrates through conventional biological assays as well as via in situ and ex situ spectroscopic techniques. Accordingly, the chemical behavior of different bioceramic substrates during their interactions with mesenchymal cells could be unfolded and compared with that of biomedical titanium alloy. Our goal was to clarify the cascade of chemical equations behind the biological processes that govern osteoblastogenic effects on different biomaterial substrates.

Predictability of Microbial Adhesion to Dental Materials by Roughness Parameters

Microbial adhesion to intraoral biomaterials is associated with surface roughness. For the prevention of oral pathologies, smooth surfaces with little biofilm formation are required. Ideally, appropriate roughness parameters make microbial adhesion predictable. Although a multitude of parameters are available, surface roughness is commonly described by the arithmetical mean roughness value (Ra). The present study investigates whether Ra is the most appropriate roughness parameter in terms of prediction for microbial adhesion to dental biomaterials. After four surface roughness modifications using standardized polishing protocols, zirconia, polymethylmethacrylate, polyetheretherketone, and titanium alloy specimens were characterized by Ra as well as 17 other parameters using confocal microscopy. Specimens of the tested materials were colonized by C. albicans or S. sanguinis for 2 h; the adhesion was measured via luminescence assays and correlated with the roughness parameters. The adhesion of C. albicans showed a tendency to increase with increasing the surface roughness—the adhesion of S. sanguinis showed no such tendency. Although Sa, that is, the arithmetical mean deviation of surface roughness, and Rdc, that is, the profile section height between two material ratios, showed higher correlations with the microbial adhesion than Ra, these differences were not significant. Within the limitations of this in-vitro study, we conclude that Ra is a sufficient roughness parameter in terms of prediction for initial microbial adhesion to dental biomaterials with polished surfaces.

Three-Dimensional Finite Element Analysis of Stress Distribution in Zirconia and Titanium Dental Implants

Zirconia has been presented as an alternative biomaterial to titanium, commercially presented as a single-body implant and/or as an abutment, demonstrating clinically biocompatible favorable results in white and rose esthetics. However, the number of long-term in vivo studies and mechanical tests evaluating the response of stress distribution compared with titanium implants is still limited. The aim of the study was to compare the principal peak stresses in the peri-implant bone around titanium and zirconia implants using the finite element method. Four groups of 3-dimensional models were constructed for the tests: G1, external hexagon titanium implant with a zirconia abutment; G2, zirconia implant with a zirconia abutment; G3, single-body titanium implant; and G4, single-body zirconia implant. Axial and oblique loads of 100 N at 45° were simulated in the prosthetic crown. The bone results showed that the peak stresses decreased by 12% in zirconia implants with 2 parts for axial load and 30% for the oblique load. In single-body implants, the peak stresses decreased 12% in the axial load and 34% in the oblique load when a zirconia implant was used compared with a titanium implant. Although the stress values in megapascals are similar, it can be concluded that the zirconia implants decrease the stress peaks at the peri-implant bone area around the implant platform when compared with titanium implants.

Modification of the Ceramic Implant Surfaces from Zirconia by the Magnetron Sputtering of Different Calcium Phosphate Targets: A Comparative Study

In this study, thin calcium phosphate (Ca-P) coatings were deposited on zirconia substrates by radiofrequency (RF) magnetron sputtering using different calcium phosphate targets (calcium phosphate tribasic (CPT), hydroxyapatite (HA), calcium phosphate monobasic, calcium phosphate dibasic dehydrate (DCPD) and calcium pyrophosphate (CPP) powders). The sputtering of calcium phosphate monobasic and DCPD powders was carried out without an inert gas in the self-sustaining plasma mode. The physico-chemical, mechanical and biological properties of the coatings were investigated. Cell adhesion on the coatings was examined using mesenchymal stem cells (MSCs). The CPT coating exhibited the best cell adherence among all the samples, including the uncoated zirconia substrate. The cells were spread uniformly over the surfaces of all samples.

Fatigue behavior and surface characterization of a Y-TZP after laboratory grinding and regeneration firing

This study evaluated the effect of grinding and regeneration firing on the flexural fatigue limit and surface characterization of Lava™ Y-TZP ceramic. Forty bar-shaped specimens with 20 × 4.0 × 1.2 mm constituted the as-sintered group (AS = control group), and 80 specimens with 20 × 4.0 × 1.5 mm were ground with cylindrical laboratory stone under water-cooling (WG) or in a dry condition (G) to reach 1.2 mm in thickness. Half of specimens were submitted to regeneration firing (1000 °C, 30 min), forming the groups AS/R, WG/R and G/R. Fatigue limit (500,000 cycles, 10 Hz) was determined by staircase method in a 4-point flexural fixture. Data were analyzed by 2-way ANOVA and Tukey HSD tests (α = 0.05). The surface topography (n = 3) and fracture area (n = 3) were evaluated by SEM. Samples were also analyzed by Rietveld refinement from X-ray diffraction data. ANOVA revealed significant differences (P < .001) for grinding protocol, regeneration firing and their interaction. In the groups not submitted to regeneration firing, the mean flexural fatigue limit of WG was higher (P < .05) than that of G and AS, with no statistical difference between each other (P > .05). After regeneration firing the inequality WG>AS>G (P < .05) was observed. The regeneration firing increased the fatigue limit of AS group and decreased those of G and WG groups (P < .05). Grinding protocols created evident grooves on zirconia surface. Failures initiated on tensile side of all specimens. The percentages (wt%) of monoclinic phase before cyclic loading were: AS (7.4), AS/R (6.5), G (2.8), G/R (0.0), WG (4.4), WG/R (0.0); and after cyclic loading: AS (8.6), AS/R (1.2), G (2.4), G/R (5.7), WG (6.3), WG/R (0.0). Wet grinding did not compromise the fatigue limit of zirconia, increasing its mechanical strength. Regeneration firing reduced the fatigue limit of ground samples, despite reducing the amount of monoclinic phase in all experimental conditions.

Current status of zirconia implants in dentistry: preclinical tests

PURPOSE

This systematic review aimed to provide an overview of zirconia implants as well as regarding the outcome of the implant-restorative complex in preclinical studies.

STUDY SELECTION

An electronic search of the literature prior to July 2017 was performed to identify all articles related to preclinical research on zirconia implants. The search was conducted using MEDLINE (National Library of Medicine) and PubMed without restrictions concerning the date of publication. The search terminology included: zirconia implant, osseointegration, bone-to-implant contact, soft tissue, histology, histomorphometry, surface modification, surface roughness, surface characteristics, and restoration (connecting multiple keywords with AND, OR).

RESULTS

Fifty-seven studies were finally selected from an initial yield of 654 titles, and the data were extracted. The identified preclinical studies focused on several aspects related to zirconia implants, namely biocompatibility, mechanical properties, implant design, osseointegration capacity, soft tissue response, and restorative options. Due to heterogeneity of the studies, a meta-analysis was not possible. The most frequently used zirconia material for the fabrication of implants is yttria-stabilized tetragonal zirconia polycrystal. The resistance-to-fracture for zirconia implants ranged between 516-2044N. The mostly investigated parameter was osseointegration, which is compared to that of titanium. A lack of evidence was found with other parameters.

CONCLUSIONS

Due to its good biocompatibility as well as favorable physical and mechanical properties, zirconia implants are a potential alternative to titanium implants. However, knowledge regarding the implant-restorative complex and related aspects is still immature to recommend its application for daily practice.

Effect of Surface Modification on Viability of L929 Cells on Zirconia Nanocomposite Substrat

Introduction: Zirconia bioceramic can be considered for metallic replacement in dental implant applications. A proper method of surface modification may promote better osseointegration. Methods: In study evaluated viability of fibroblast cell following surface treatment. Therefore, viability L929 cells were characterized using MTT assay and scanning electron microscopy. Results: The viability assessment determined significant differences A-Y-TZP20 without surface treatment as compared to laser surface treatment (B), laser surface treatment + hydroxyapatiteyttrium stabilized tetragonal zirconia nanocomposite coat (C) and control. This study demonstrated that L929 cells approximately proliferated and spread on A-Y-TZP20 nanocomposite disk in laser surface treatment(B), Laser surface treatment + hydroxiapatite-yttrium stabilized tetragonal zirconia nanocomposite coat (C) groups similar to control group. Conclusion: Laser surface treatment showed positive effect on the viability of L929 cells.

Applications of Laser Welding in Dentistry: A State-of-the-Art Review

The dental industry without lasers is inconceivable right now. This captivating technology has outlasted other possible alternative technologies applied in dentistry in the past due to its precision, accuracy, minimal invasive effect as well as faster operating time. Other alternatives such as soldering, resistance (spot) welding, plasma (torch) welding, and single pulse tungsten inert gas welding have their pros and cons; nevertheless, laser welding remains the most suitable option so far for dental application. This paper attempts to give an insight into the laser principle and types of lasers used for dental purposes, types of dental alloys used by the dentist, and effect of laser parameters on prosthesis/implants. It is apparent from the literature review that laser assisted dental welding will continue to grow and will become an unparalleled technology for dental arena.

Fracture resistance of implant- supported monolithic crowns cemented to zirconia hybrid-abutments: zirconia-based crowns vs. lithium disilicate crowns

PURPOSE

The aim of this in vitro study was to investigate the fracture resistance under chewing simulation of implant-supported posterior restorations (crowns cemented to hybrid-abutments) made of different all-ceramic materials.

MATERIALS AND METHODS

Monolithic zirconia (MZr) and monolithic lithium disilicate (MLD) crowns for mandibular first molar were fabricated using computer-aided design/computer-aided manufacturing technology and then cemented to zirconia hybrid-abutments (Ti-based). Each group was divided into two subgroups (n=10): (A) control group, crowns were subjected to single load to fracture; (B) test group, crowns underwent chewing simulation using multiple loads for 1.2 million cycles at 1.2 Hz with simultaneous thermocycling between 5℃ and 55℃. Data was statistically analyzed with one-way ANOVA and a Post-Hoc test.

RESULTS

All tested crowns survived chewing simulation resulting in 100% survival rate. However, wear facets were observed on all the crowns at the occlusal contact point. Fracture load of monolithic lithium disilicate crowns was statistically significantly lower than that of monolithic zirconia crowns. Also, fracture load was significantly reduced in both of the all-ceramic materials after exposure to chewing simulation and thermocycling. Crowns of all test groups exhibited cohesive fracture within the monolithic crown structure only, and no abutment fractures or screw loosening were observed.

CONCLUSION

When supported by implants, monolithic zirconia restorations cemented to hybrid abutments withstand masticatory forces. Also, fatigue loading accompanied by simultaneous thermocycling significantly reduces the strength of both of the all-ceramic materials. Moreover, further research is needed to define potentials, limits, and long-term serviceability of the materials and hybrid abutments.

Bone response to functionally loaded, two-piece zirconia implants: A preclinical histometric study

OBJECTIVE

To evaluate the bone response to a two-piece zirconia implant in comparison with a control titanium implant in the canine mandible 4 and 16 weeks after restoration.

MATERIAL AND METHODS

Zirconia and titanium implants were alternately placed bilaterally in healed mandibular molar and premolar sites of five canines. Full-ceramic single-tooth restorations were cemented after 6 weeks of transmucosal healing, allowing for full functional loading of the implants. Histologic and histometric analyses were performed on orofacial and mesiodistal undecalcified sections of the specimens obtained upon sacrifice after 4 and 16 weeks of functional loading. Bone-to-implant contact (BIC), multinucleated giant cells-to-implant contact (MIC), crestal bone level, and peri-implant bone density were histometrically assessed.

RESULTS

All 60 implants and 60 restorations were still in function after 4 and 16 weeks of loading in both test and control groups. No implant loss, no implant or abutment fracture, and no chipping of the restorations could be detected. Histometric analysis showed no statistically significant differences between zirconia and titanium implants in BIC, crestal bone level, and peri-implant bone density at both time points. Between 4 and 16 weeks, the crestal bone level around zirconia implants showed a small but statistically significant increase in its distance from the implant shoulder. MIC was very low on both implant types and both time points and decreased statistically significantly overtime.

CONCLUSION

The present two-piece zirconia implant showed a similar bone integration compared to the titanium implant with similar surface morphology after 4 and 16 weeks of loading.

Twist removal of healed vs. nonhealed implants-a mechanical and histological study in mini pigs

PURPOSE

The objective of this study was to evaluate the effect of removal torque (reverse torque) of titanium implants in peri-implant bone.

METHODS

The P1-M1 teeth were extracted bilaterally of 6 mini pigs (BR-1). Each animal received 6 titanium implants, three for each side of mandible. On the right side of mandible, 3 implants reminded 9 months (9M) under masticatory activity and on the left side, other 3 implants were placed and immediately removed (IR). All 36 implants were removed by removal torque, and the recorded values were statistically analyzed. Animals were euthanized right after the removal torque and recording. Each third (cervical, medium, and apical) of peri-implant bone was extracted and analyzed histological and immunohistochemically. Student's t test was used to determine statistical differences in the values between the 9M and IR samples. Data were presented as means with standard deviations. The level of significance was set at 5% (P < 0.05).

RESULTS

Removal torque was higher in 9M experimental situation than in IR. Histological characteristics of mature bone were presented in the 9M experimental condition, and immature bone characteristics were presented in the IR experimental condition. Removal torque caused small fractures and rounding in the bone grooving. Immunohistochemical analysis reinforced the histological results; Student's t test provided statistically significant differences to osteocalcin expression in 9M samples and no statistically significant differences expression to collagen I in both experimental conditions (P < 0.05).

CONCLUSIONS

Removal torque caused microscopical fractures and smoothing in the peri-implant bone grooves, but it does not compromise the bone healing.

A novel method of surface modification by electrochemical deoxidation: Effect on surface characteristics and initial bioactivity of zirconia

The aim of this study was to investigate and compare the surface characteristics and initial bioactivity of ceria-stabilized zirconia/alumina nanocomposite (NANOZR) with those of yttria-stabilized zirconia (3Y-TZP) and pure titanium (CpTi) following the use of three surface modification methods; polishing, sandblasting/acid-etching (SB-E) and electrochemical deoxidation (ECD). Physical properties including surface morphology, chemical composition, X-ray diffraction, surface wettability, surface roughness, and hardness were measured. Osteoblast-like MC3T3-E1 cells were used to examine cell morphology and attachment to the surfaces of the materials. ECD treated NANOZR (NANOZR-E) showed a well-arranged, self-organized microporous surface structure with significantly low contact angles when compared with the other specimens (p < 0.05). NANOZR-E also demonstrated a slight decrease in monoclinic phase content (-4.4 wt %). The morphology and attachment of MC3T3-E1 cells on NANOZR-E were similar to those on polished and SBE-treated CpTi surfaces. Higher cell affinity was observed on NANOZR-E when compared with ECD treated 3Y-TZP. The findings of this study indicate the effectiveness of the novel technique, ECD, in the formation of a microporous surface on NANOZR when compared with both CpTi and 3Y-TZP. Moreover, this method also appears to improve the biological activity of NANOZR during the initial stage. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 2641-2652, 2017.

Bone tissue response to experimental zirconia implants

OBJECTIVES

This study seeks to assess the bone tissue response at experimental zirconia implants in comparison with titanium implants by means of descriptive histology and histomorphometry in a dog model.

MATERIALS AND METHODS

Experimental zirconia implants with three different surface roughnesses (Z1 < Z2 < Z3) and conventional sandblasted large grit and acid-etched titanium implants were inserted bilaterally in the lower jaws of nine beagle dogs. Tissue biopsies were obtained after 3 and 14 days and 10 weeks of transmucosal healing. The tissue response was investigated by assessing new, old, and total bone-to-implant contact (nBIC, oBIC, and tBIC).

RESULTS

After 3 days, histological specimens of all groups showed an intimate contact between the implant threads and pristine bone (tBIC: Ti 42.3 % > Z2 30.1 % > Z3 28.9 % > Z1 25.1 %, p > 0.05, unpaired t test, respectively). A provisional matrix was evident at all implant surfaces. At 14 days, percentages of BIC increased in all groups (tBIC: Ti 62.1 % > Z3 69.2 % < Z2 44.4 % > Z1 42.3 %; nBIC: Z3 58.9 % > Ti 52.2 % > Z2 35.1 % > Z1 32.5 %). Two implants, one of group Z1 and one of group Z2, were lost. At 10 weeks, 13 of 18 zirconia implants were lost, equally distributed between all three surface modifications. The remaining implants revealed increased BIC values (tBIC: Z3 69.5 % > Ti 58.5 % > Z1 49.7 % > Z2 37.1 %; nBIC: Z3 57.2 % > Ti 46.5 % > Z1 32.3 % > Z2 29.3 %). Histomorphometrical analysis showed comparable mean BIC values in all groups at all healing periods without showing statistical differences (p > 0.05, unpaired t test, respectively).

CONCLUSION

The bone tissue response throughout the healing periods was characterized by a constant bone remodeling accompanied by resorption of old bone in favor of new bone formation at both titanium and zirconia implants. Surface roughness had a positive effect on BIC, although not showing statistical significance. Due to the poor survival rate, the experimental zirconia implants investigated may not be suitable for clinical use.

CLINICAL RELEVANCE

Zirconia has been introduced as an alternative biomaterial for dental implants. A profound knowledge about the bone tissue response at zirconia implant surfaces is necessary as it plays an important role for proper osseointegration and long-term stability.

A systematic review of the clinical survival of zirconia implants

OBJECTIVES

The aim of this review was to evaluate the clinical success and survival rates of zirconia ceramic implants after at least 1 year of function and to assess if there is sufficient evidence to justify using them as alternatives to titanium implants.

MATERIALS AND METHODS

An electronic search in MEDLINE, EMBASE, and the Cochrane Central Register of Controlled Clinical Trials (CENTRAL) databases was performed in April 2015 by two independent examiners to retrieve clinical studies focusing on the survival rate of zirconia implants after at least 1 year of function. Implant survival was estimated using the overall proportion reported in the studies with a Clopper-Pearson 95 % confidence interval (random effect model with a Der-Simonian Laird estimate).

RESULTS

Fourteen articles were selected out of the 1519 titles initially screened. The overall survival rate of zirconia one- and two-piece implants was calculated at 92 % (95 % CI 87-95) after 1 year of function. The survival of implants at 1 year for the selected studies revealed considerable heterogeneity.

CONCLUSIONS

In spite of the unavailability of sufficient long-term evidence to justify using zirconia oral implants, zirconia ceramics could potentially be the alternative to titanium for a non-metallic implant solution. However, further clinical studies are required to establish long-term results, and to determine the risk of technical and biological complications. Additional randomized controlled clinical trials examining two-piece zirconia implant systems are also required to assess their survival and success rates in comparison with titanium as well as one-piece zirconia implants.

CLINICAL RELEVANCE

Zirconia implants provide a potential alternative to titanium ones. However, clinicians must be aware of the lack of knowledge regarding long-term outcomes and specific reasons for failure.

Histological assessment of hard and soft tissues surrounding a novel ceramic implant: a pilot study in the minipig

OBJECTIVE

The aim of this study was to investigate clinical and soft/hard tissues histomorphological outcomes of a ceramic implant comparatively to a titanium implant in a minipig model.

MATERIAL AND METHODS

Eighteen soft tissue level implants (9 Ceramic with ZLA(®) surface as test, and 9 titanium SLActive(®) as control, Institut Straumann, Basel, Switzerland) were randomly placed into the mandible of 6 minipigs (n = 6). Two months later, animals were sacrificed and block biopsies were obtained to assess histomorphological outcomes. Unadjusted paired comparisons, of both groups were performed using the Wilcoxon signed rank test. The Dunnett-Hsu test was used to adjust for multiple comparisons.

RESULTS

All implants showed excellent integration into bone and soft tissue. The fBIC (distance implant shoulder to most coronal implant contact) and BIC% (percentage bone-to-implant contact) were for both groups; test: 3.95 mm and 85.4%; control 3.97 mm and 84.3% respectively. No difference in peri-implant mucosa height was found, however, the sulcular epithelium was significantly shorter for the ZrO2 (mean: 0.76, 95%CI: 0.46-1.06) than for the Ti (mean: 1.40, 95%CI: 1.10-1.70) (p = 0.0090).

CONCLUSIONS

Within the limits of this pilot study, no difference was found between the ceramic implant with ZLA(®) surface and a titanium implant in terms of bone tissue integration. Furthermore, the epithelial attachment favoured this ceramic implant over titanium.

The role of prosthetic abutment material on the stress distribution in a maxillary single implant-supported fixed prosthesis

PURPOSE

Evaluate the influence of abutment's material and geometry on stress distribution in a single implant-supported prosthesis.

MATERIALS AND METHODS

Three-dimensional models were made based on tomographic slices of the upper middle incisor area, in which a morse taper implant was positioned and a titanium (Ti) or zirconia (ZrN) universal abutments was installed. The commercially available geometry of titanium (T) and zirconia (Z) abutments were used to draw two models, TM1 and ZM1 respectively, which served as control groups. These models were compared with 2 experimental groups were the mechanical properties of Z were applied to the titanium abutment (TM2) and vice versa for the zirconia abutment (ZM2). Subsequently, loading was simulated in two steps, starting with a preload phase, calculated with the respective friction coefficients of each materials, followed by a combined preload and chewing force. The maximum von Mises stress was described. Data were analyzed by two-way ANOVA that considered material composition, geometry and loading (p<0.05).

RESULTS

Titanium and zirconia abutments showed similar von Mises stresses in the mechanical part of the four models. The area with the highest concentration of stress was the screw thread, following by the screw body. The highest stress levels occurred in screw thread was observed during the preloading phase in the ZM1 model (931MPa); and during the combined loading in the TM1 model (965MPa). Statistically significant differences were observed for loading, the material×loading interaction, and the loading×geometry interaction (p<0.05). Preloading contributed for 77.89% of the stress (p<0.05). There were no statistically significant differences to the other factors (p>0.05).

CONCLUSION

The screw was the piece most intensely affected, mainly through the preload force, independent of the abutment's material.

Influence of Metal and Ceramic Abutments on the Stress Distribution Around Narrow Implants: A Photoelastic Stress Analysis

PURPOSE

This study aimed to compare, through photoelastic analysis, the distribution of stresses around narrow implants with external hexagon (EH) and Morse taper (MT) connections, when single crowns made with metal and ceramic abutments were used.

MATERIALS AND METHODS

Six photoelastic models were prepared, simulating the use of narrow EH and MT implants replacing a lateral incisor. These 2 groups received 3 different abutments: prefabricated metal abutments, customized metal abutments, and customized zirconia abutments. All crowns were identical and made with a leucite reinforced glass-ceramic. Vertical loads of 0 to 100 N were applied on the palatal surface of the crowns, and the photoelastic stress fringes developed in each model were captured in a high-definition video, and digital photographs were taken at 100 N.

RESULTS

The abutment type and material influenced the stress distribution patterns around narrow implants with EH and MT connections. Stresses were generated mainly around the apical and lingual regions of the implants.

CONCLUSIONS

For both connections, the prefabricated metal abutments presented better stress distribution around the implants when compared to customized metal and zirconia abutments because low stress levels were developed in smaller areas around the implants.

Implant Supported Fixed Dental Prostheses Using a New Monotype Zirconia Implant-A Case Report

Currently, titanium or specific titanium alloys are the most often used materials for the fabrication of dental implants. Many studies have confirmed the osseointegrative capacity and clinical long-term performance of moderately rough titanium implants. However, disadvantages have also been reported with regard to peri-implant infections and the titanium metal properties. Tooth colored ceramic implants have attracted the interest of clinicians since the end of the 1960s. Initially, alumina was used for the fabrication of ceramic implants; however, due to the poor biomechanical properties, alumina implants are not commercially available any more. Since end of the 1990s, zirconia has been established in dentistry due to its superior biomechanical properties compared to other oxide ceramics such as alumina. Currently, zirconia is the material of choice for the fabrication of ceramic implants. Zirconia implants show superior biocompatibility compared to titanium and other metals. Additionally, it has been reported that zirconia implants with a micro-rough surface topography show at least a comparable osseointegrative capacity and similar clinical survival rates to moderately rough titanium implants. The present case reports a fixed implant-supported reconstruction of a large edentulous space with compromised local bone conditions using new monotype zirconia dental implants with a micro-rough surface topography.