Freeze Casting for Assembling Bioinspired Structural Materials

Bioinspired Highly Anisotropic, Ultrastrong and Stiff, and Osteoconductive Mineralized Wood Hydrogel Composites for Bone Repair

Anisotropic hydrogels mimicking the biological tissues with directional functions play essential roles in damage‐tolerance, cell guidance and mass transport. However, conventional synthetic hydrogels often have an isotropic network structure, insufficient mechanical properties and lack of osteoconductivity, which greatly limit their applications for bone repair. Herein, inspired by natural bone and wood, a biomimetic strategy is presented to fabricate highly anisotropic, ultrastrong and stiff, and osteoconductive hydrogel composites via impregnation of biocompatible hydrogels into the delignified wood followed by in situ mineralization of hydroxyapatite (HAp) nanocrystals. The well‐aligned cellulose nanofibrils endow the composites with highly anisotropic structural and mechanical properties. The strong intermolecular bonds of the aligned cellulose fibrils and hydrogel/wood interaction, and the reinforcing nanofillers of HAp enable the composites remarkable tensile strength of 67.8 MPa and elastic modulus of 670 MPa, three orders of magnitude higher than those of conventional alginate hydrogels. More importantly, the biocompatible hydrogel together with aligned HAp nanocrystals could effectively promote osteogenic differentiation in vitro and induce bone formation in vivo. The bone ingrowth into the hydrogel composite scaffold also yields good osteointegration. This study provides a low‐cost, eco‐friendly, feasible, and scalable approach for fabricating anisotropic, strong, stiff, hydrophilic, and osteoconductive hydrogel composites for bone repair.

Bone tissue regeneration: The role of finely tuned pore architecture of bioactive scaffolds before clinical translation

Spatial dimension of pores and interconnection in macroporous scaffolds is of particular importance in facilitating endogenous cell migration and bone tissue ingrowth. However, it is still a challenge to widely tune structure parameters of scaffolds by conventional methods because of inevitable pore geometrical deformation and poor pore interconnectivity. Here, the long-term in vivo biological performances of nonstoichiometric bioceramic scaffolds with different pore dimensions were assessed in critical-size femoral bone defect model. The 6% Mg-substituted wollastonite (CSi-Mg6) powders were prepared via wet-chemical precipitation and the scaffolds elaborately printed by ceramic stereolithography, displaying designed constant pore strut and tailorable pore height (200, 320, 450, 600 μm), were investigated thoroughly in the bone regeneration process. Together with detailed structural stability and mechanical properties were collaboratively outlined. Both μCT and histological analyses indicated that bone tissue ingrowth was retarded in 200 μm scaffolds in the whole stage (2-16 weeks) but the 320 μm scaffolds showed appreciable bone tissue in the center of porous constructs at 6-10 weeks and matured bone tissue were uniformly invaded in the whole pore networks at 16 weeks. Interestingly, the neo-tissue ingrowth was facilitated in the 450 μm and 600 μm scaffolds after 2 weeks and higher extent of bone regeneration and remodeling at the later stage. These new findings provide critical information on how engineered porous architecture impact bone regeneration in vivo. Simultaneously, this study shows important implications for optimizing the porous scaffolds design by advanced additive manufacture technique to match the clinical translation with high performance.

Hierarchically maze-like structured nanofiber aerogels for effective low-frequency sound absorption

Noise has been regarded as an environmental pollutant that greatly affects people's physical and psychiatric health. Fibrous sound absorption materials are widely used to release the annoyance that brought by noise pollution, however, the fibrous materials are limited by poor sound absorption ability in low-frequency, heavyweight, and excessive thickness. Herein, composite nanofiber aerogels are designed with a hierarchical maze-like microstructure, which is fabricated by interweaving the cellulose nanocrystal lamellas with polyacrylonitrile electrospun nanofiber networks through the freeze-casting technique. The designed maze-like structure shows obvious enhancement in the low-frequency sound absorption band compared to the fiber aerogels made by the network structure. Moreover, through carefully regulating the maze structure, composite nanofiber aerogels with excellent sound absorption performance (with an NRC of 0.58) and lightweight property (11.05 mg cm^-3) can be fabricated. In addition to the superior sound absorption ability, the hierarchical nature of the maze-like structure also guarantees the nanofiber aerogels with robust mechanical properties, which can be tailored to various shaped objects on a large scale. These favorable characters present that the composite nanofiber aerogels potential choice for sound absorption in the fields of vehicles, buildings, and indoor reverberation.

Alignment of Cellulose Nanofibers: Harnessing Nanoscale Properties to Macroscale Benefits

In nature, cellulose nanofibers form hierarchical structures across multiple length scales to achieve high-performance properties and different functionalities. Cellulose nanofibers, which are separated from plants or synthesized biologically, are being extensively investigated and processed into different materials owing to their good properties. The alignment of cellulose nanofibers is reported to significantly influence the performance of cellulose nanofiber-based materials. The alignment of cellulose nanofibers can bridge the nanoscale and macroscale, bringing enhanced nanoscale properties to high-performance macroscale materials. However, compared with extensive reviews on the alignment of cellulose nanocrystals, reviews focusing on cellulose nanofibers are seldom reported, possibly because of the challenge of aligning cellulose nanofibers. In this review, the alignment of cellulose nanofibers, including cellulose nanofibrils and bacterial cellulose, is extensively discussed from different aspects of the driving force, evaluation, strategies, properties, and applications. Future perspectives on challenges and opportunities in cellulose nanofiber alignment are also briefly highlighted.

Recent Progress on Nanocellulose Aerogels: Preparation, Modification, Composite Fabrication, Applications

The rapid development of modern industry and excessive consumption of petroleum-based polymers have triggered a double crisis presenting a shortage of nonrenewable resources and environmental pollution. However, this has provided an opportunity to stimulate researchers to harness native biobased materials for novel advanced materials and applications. Nanocellulose-based aerogels, using abundant and sustainable cellulose as raw material, present a third-generation of aerogels that combine traditional aerogels with high porosity and large specific surface area, as well as the excellent properties of cellulose itself. Currently, nanocellulose aerogels provide a highly attention-catching platform for a wide range of functional applications in various fields, e.g., adsorption, separation, energy storage, thermal insulation, electromagnetic interference shielding, and biomedical applications. Here, the preparation methods, modification strategies, composite fabrications, and further applications of nanocellulose aerogels are summarized, with additional discussions regarding the prospects and potential challenges in future development.

Novel bio-inspired three-dimensional nanocomposites based on montmorillonite and chitosan

In this study, inspired by nacre-like structural natural shells, novel three-dimensional (3D) nanocomposites based on natural nanoplatelets of montmorillonite (MMT) and polysaccharide of chitosan (CS) were prepared with solution intercalation and self-assembly process. The CS-intercalated-MMT nanoplatelets units acted as "bricks" and CS molecules acted as "mortar", arranging in fairly well-ordered layered structure. With addition of glutaraldehyde (GA) and Pd²⁺ cations, synergistic toughening and strengthening effects of covalent and ionic bonds could be achieved. The best mechanical properties of the prepared 3D nanocomposites were observed as 5.6 KJ/m² (impact strength), 3.3 GPa (flexural modulus), and 65.8 MPa (flexural strength), respectively, which showed higher toughness but lower flexural properties than natural pearl mussel shells. Nevertheless, both the impact and flexural properties of the prepared 3D nanocomposite were much higher than the other natural shell, i.e. green grab shell. Besides conventional methods characterizations, the nacre-like structure of the artificial 3D nanocomposite was further evidenced with positron annihilation lifetime spectroscopy characterizations. This work might facilitate a versatile platform for developing green 3D bionanocomposites with fairly good mechanical properties.

Cryostructuring of Polymeric Systems. 55. Retrospective View on the More than 40 Years of Studies Performed in the A.N.Nesmeyanov Institute of Organoelement Compounds with Respect of the Cryostructuring Processes in Polymeric Systems

The processes of cryostructuring in polymeric systems, the techniques of the preparation of diverse cryogels and cryostructurates, the physico-chemical mechanisms of their formation, and the applied potential of these advanced polymer materials are all of high scientific and practical interest in many countries. This review article describes and discusses the results of more than 40 years of studies in this field performed by the researchers from the A.N.Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences-one of the key centers, where such investigations are carried out. The review includes brief historical information, the description of the main effects and trends characteristic of the cryostructuring processes, the data on the morphological specifics inherent in the polymeric cryogels and cryostructurates, and examples of their implementation for solving certain applied tasks.

3D Graphene Materials: From Understanding to Design and Synthesis Control

Carbon materials, with their diverse allotropes, have played significant roles in our daily life and the development of material science. Following 0D C₆₀ and 1D carbon nanotube, 2D graphene materials, with their distinctively fascinating properties, have been receiving tremendous attention since 2004. To fulfill the efficient utilization of 2D graphene sheets in applications such as energy storage and conversion, electrochemical catalysis, and environmental remediation, 3D structures constructed by graphene sheets have been attempted over the past decade, giving birth to a new generation of graphene materials called 3D graphene materials. This review starts with the definition, classifications, brief history, and basic synthesis chemistries of 3D graphene materials. Then a critical discussion on the design considerations of 3D graphene materials for diverse applications is provided. Subsequently, after emphasizing the importance of normalized property characterization for the 3D structures, approaches for 3D graphene material synthesis from three major types of carbon sources (GO, hydrocarbons and inorganic carbon compounds) based on GO chemistry, hydrocarbon chemistry, and new alkali-metal chemistry, respectively, are comprehensively reviewed with a focus on their synthesis mechanisms, controllable aspects, and scalability. At last, current challenges and future perspectives for the development of 3D graphene materials are addressed.

Pristine Titanium Carbide MXene Hydrogel Matrix

The hydrogel matrix normally forms via covalent or noncovalent interactions that make the matrix resistant to hydration and disassembly. Herein this type of chemical transition is demonstrated in titanium carbide MXene (Ti₃C₂T_x), in which the exchange of intercalated Li⁺ with hydrated protons triggers significantly suppressed hydration in stacked Ti₃C₂T_x. Based on this intercalation chemistry behavior, pristine Ti₃C₂T_x hydrogel matrices with an arbitrary microstructures are fabricated by freezing-induced preassembly and a subsequent specially designed thawing process in protic acids. The absence of extrinsic components maximizes the materials performance of the resultant pristine Ti₃C₂T_x hydrogel, which produces a compressive modulus of 2.4 MPa and conductivity of 220.3 ± 16.8 S/m at 5 wt % solid content. The anisotropic Ti₃C₂T_x hydrogel also delivers a promising performance in solar steam generation by facilitating rapid water transport inside vertical microchannels.

Controlling ice formation on gradient wettability surface for high-performance bioinspired materials

Ice-templating holds promise to become a powerful technique to construct high-performance bioinspired materials. Both ice nucleation and growth during the freezing process are crucial for the final architecture of the ice-templated material. However, effective ways to control these two very important factors are still lacking. Here, we demonstrate that successive ice nucleation and preferential growth can be realized by introducing a wettability gradient on a cold finger. A bulk porous material with a long-range lamellar pattern was obtained using a linear gradient, yielding a high-performance, bulk nacre-mimetic composite with excellent strength and toughness after infiltration. In addition, cross-aligned and circular lamellar structures can be obtained by freeze-casting on surfaces modified with bilayer linear gradient and radial gradient, respectively, which are impossible to realize with conventional freeze-casting techniques. Our study highlights the potential of harnessing the rich designability of surface wettability patterns to build high-performance bulk materials with bioinspired complex architectures.

Freeze Casting: From Low-Dimensional Building Blocks to Aligned Porous Structures-A Review of Novel Materials, Methods, and Applications

Freeze casting, also known as ice templating, is a particularly versatile technique that has been applied extensively for the fabrication of well-controlled biomimetic porous materials based on ceramics, metals, polymers, biomacromolecules, and carbon nanomaterials, endowing them with novel properties and broadening their applicability. The principles of different directional freeze-casting processes are described and the relationships between processing and structure are examined. Recent progress in freeze-casting assisted assembly of low dimensional building blocks, including graphene and carbon nanotubes, into tailored micro- and macrostructures is then summarized. Emerging trends relating to novel materials as building blocks and novel freeze-cast geometries-beads, fibers, films, complex macrostructures, and nacre-mimetic composites-are presented. Thereafter, the means by which aligned porous structures and nacre mimetic materials obtainable through recently developed freeze-casting techniques and low-dimensional building blocks can facilitate material functionality across multiple fields of application, including energy storage and conversion, environmental remediation, thermal management, and smart materials, are discussed.

Ultralight Programmable Bioinspired Aerogels with an Integrated Multifunctional Surface for Self-Cleaning, Oil Absorption, and Thermal Insulation via Coassembly

Creating a configurable and controllable surface for structure-integrated multifunctionality of ultralight aerogels is of significance but remains a huge challenge because of the critical limitations of mechanical vulnerability and structural processability. Herein, inspired by Salvinia minima, the facile and one-step coassembly approach is developed to allow the structured aerogels to spontaneously replicate Salvinia-like textures for function-adaptable surfaces morphologically. The in situ superimposed construction of bioinspired topography and intrinsic topology is for the first time performed for programmable binary architectures with multifunctionality without engendering structural vulnerability and functional disruption. By introducing the binding groups for hydrophobicity tailoring, functionalized nanocellulose (f-NC) is prepared via mechanochemistry as a structural, functional, and topographical modifier for a multitasking role. The self-generated bioinspired surface with f-NC greatly maintains the structural unity and mechanical robustness, which enable self-adaptability and self-supporting of surface configurations. With fine-tuning of nucleation-driving, the binary microstructures can be controllably diversified for structure-adaptable multifunctionalities. The resulting ultralight S. minima-inspired aerogels (e.g., 0.054 g cm^-3) presented outstanding temperature-endured elasticity (e.g., 90.7% high-temperature compress-recovery after multiple cycles), durable superhydrophobicity, anti-icing properties, oil absorbency efficiency (e.g., 60.2 g g^-1), and thermal insulating (e.g., 0.075 W mK^-1), which are superior to these reported on the overall performance. This coassembly strategy offers the opportunities for the design of ultralight materials with topography- and function-tailorable features to meet the increasing demands in many fields such as smart surfaces and self-cleaning coatings.

3D printing of Haversian bone-mimicking scaffolds for multicellular delivery in bone regeneration

The integration of structure and function for tissue engineering scaffolds is of great importance in mimicking native bone tissue. However, the complexity of hierarchical structures, the requirement for mechanical properties, and the diversity of bone resident cells are the major challenges in constructing biomimetic bone tissue engineering scaffolds. Herein, a Haversian bone-mimicking scaffold with integrated hierarchical Haversian bone structure was successfully prepared via digital laser processing (DLP)-based 3D printing. The compressive strength and porosity of scaffolds could be well controlled by altering the parameters of the Haversian bone-mimicking structure. The Haversian bone-mimicking scaffolds showed great potential for multicellular delivery by inducing osteogenic, angiogenic, and neurogenic differentiation in vitro and accelerated the ingrowth of blood vessels and new bone formation in vivo. The work offers a new strategy for designing structured and functionalized biomaterials through mimicking native complex bone tissue for tissue regeneration.

A Review on Graphene Fibers: Expectations, Advances, and Prospects

Graphene fiber (GF) is a macroscopically assembled fibrous material made of individual units of graphene and its derivatives. Beyond traditional carbon fibers, graphene building blocks consisting of regulable sizes and regular orientations of GF are expected to generate extreme mechanical and transport properties, as well as multiple functions in smart electronic fibrous devices and textiles. Here, the features of GF are presented along four lines: preparation, morphology, structure-performance correlations, and state-of-the-art applications as flexible and wearable electronics. The principles, experiments, and keys of fabricating GF from graphite with different methods, focusing on the industrially viable mainstream strategy, wet spinning, are introduced. Then, the fundamental relationship between the mechanical and transport properties and the structure, including both highly condensed structures for high-performance and hierarchical structures for multiple functions, is presented. The advances of GF based on structure-performance formulas boost its functional applications, especially in electronic devices. Finally, the possible promotion methods and structural-functional integrated applications of GF are discussed.

Cryopolymerization enables anisotropic polyaniline hybrid hydrogels with superelasticity and highly deformation-tolerant electrochemical energy storage

The development of energy storage devices that can endure large and complex deformations is central to emerging wearable electronics. Hydrogels made from conducting polymers give rise to a promising integration of high conductivity and versatility in processing. However, the emergence of conducting polymer hydrogels with a desirable network structure cannot be readily achieved using conventional polymerization methods. Here we present a cryopolymerization strategy for preparing an intrinsically stretchable, compressible and bendable anisotropic polyvinyl alcohol/polyaniline hydrogel with a complete recovery of 100% stretching strain, 50% compressing strain and fully bending. Due to its high mechanical strength, superelastic properties and bi-continuous phase structure, the as-obtained anisotropic polyvinyl alcohol/polyaniline hydrogel can work as a stretching/compressing/bending electrode, maintaining its stable output under complex deformations for an all-solid-state supercapacitor. In particular, it achieves an extremely high energy density of 27.5 W h kg⁻¹, which is among that of state-of-the-art stretchable supercapacitors.

Energy storage devices that can endure large and complex deformations are central to the development of wearable electronics. Here the authors present a cryopolymerization strategy for preparing an anisotropic polyvinyl alcohol/polyaniline hydrogel for flexible supercapacitor electrodes.

Elastic Aerogels of Cellulose Nanofibers@Metal-Organic Frameworks for Thermal Insulation and Fire Retardancy

Metal-organic frameworks (MOFs) with high microporosity and relatively high thermal stability are potential thermal insulation and flame-retardant materials. However, the difficulties in processing and shaping MOFs have largely hampered their applications in these areas. This study outlines the fabrication of hybrid CNF@MOF aerogels by a stepwise assembly approach involving the coating and cross-linking of cellulose nanofibers (CNFs) with continuous nanolayers of MOFs. The cross-linking gives the aerogels high mechanical strength but superelasticity (80% maximum recoverable strain, high specific compression modulus of ~ 200 MPa cm³ g^-1, and specific stress of ~ 100 MPa cm³ g^-1). The resultant lightweight aerogels have a cellular network structure and hierarchical porosity, which render the aerogels with relatively low thermal conductivity of ~ 40 mW m^-1 K^-1. The hydrophobic, thermally stable MOF nanolayers wrapped around the CNFs result in good moisture resistance and fire retardancy. This study demonstrates that MOFs can be used as efficient thermal insulation and flame-retardant materials. It presents a pathway for the design of thermally insulating, superelastic fire-retardant nanocomposites based on MOFs and nanocellulose.

Promoting Transport Kinetics in Li-Ion Battery with Aligned Porous Electrode Architectures

Developing scalable energy storage systems with high energy and power densities is essential to meeting the ever-growing portable electronics and electric vehicle markets, which calls for development of thick electrode designs to improve the active material loading and greatly enhance the overall energy density. However, rate capabilities in lithium-ion batteries usually fall off rapidly with increasing electrode thickness due to hindered ionic transport kinetics, which is especially the issue for conversion-based electroactive materials. To alleviate the transport constrains, rational design of three-dimensional porous electrodes with aligned channels is critically needed. Herein, magnetite (Fe₃O₄) with high theoretical capacity is employed as a model material, and with the assistance of micrometer-sized graphine oxide (GO) sheets, aligned Fe₃O₄/GO (AGF) electrodes with well-defined ionic transport channels are formed through a facile ice-templating method. The as-fabricated AGF electrodes exhibit excellent rate capacity compared with conventional slurry-casted electrodes with an areal capacity of ∼3.6 mAh·cm^-2 under 10 mA·cm^-2. Furthermore, clear evidence provided by galvanostatic charge-discharge profiles, cyclic voltammetry, and symmetric cell electrochemical impedance spectroscopy confirms the facile ionic transport kinetics in this proposed design.

Plant-Derived Nanocellulose as Structural and Mechanical Reinforcement of Freeze-Cast Chitosan Scaffolds for Biomedical Applications

Despite considerable recent interest in micro- and nanofibrillated cellulose as constituents of lightweight structures and scaffolds for applications that range from thermal insulation to filtration, few systematic studies have been reported to date on structure-property-processing correlations in freeze-cast chitosan-nanocellulose composite scaffolds, in general, and their application in tissue regeneration, in particular. Reported in this study are the effects of the addition of plant-derived nanocellulose fibrils (CNF), crystals (CNCs), or a blend of the two (CNB) to the biopolymer chitosan on the structure and properties of the resulting composites. Chitosan-nanocellulose composite scaffolds were freeze-cast at 10 and 1 °C/min, and their microstructures were quantified in both the dry and fully hydrated states using scanning electron and confocal microscopy, respectively. The modulus, yield strength, and toughness (work to 60% strain) were determined in compression parallel and the modulus also perpendicular to the freezing direction to quantify anisotropy. Observed were the preferential alignments of CNCs and/or fibrils parallel to the freezing direction. Additionally, observed was the self-assembly of the nanocellulose into microstruts and microbridges between adjacent cell walls (lamellae), features that affected the mechanical properties of the scaffolds. When freeze-cast at 1 °C/min, chitosan-CNF scaffolds had the highest modulus, yield strength, toughness, and smallest anisotropy ratio, followed by chitosan and the composites made with the nanocellulose blend, and that with crystalline cellulose. These results illustrate that the nanocellulose additions homogenize the mechanical properties of the scaffold through cell-wall material self-assembly, on the one hand, and add architectural features such as bridges and pillars, on the other. The latter transfer loads and enable the scaffolds to resist deformation also perpendicular to the freezing direction. The observed property profile and the materials' proven biocompatibility highlight the promise of chitosan-nanocellulose composites for a large range of applications, including those for biomedical implants and devices.

Flexible all-in-one zinc-ion batteries

The recent development of flexible and wearable electronic devices has increased the demand for energy storage devices with excellent flexibility and structural stability. Aqueous zinc-ion batteries (ZIBs) are promising energy storage devices due to their low cost, high safety, and eco-friendliness. Therefore, flexible ZIBs have to be considered. Herein, we design the flexible all-in-one ZIBs, where the reduced graphene oxide/polyaniline (rGO/PANI) cathode, cellulose nanofiber (CNF) separator, and exfoliated graphene (EG)/Zn anode are integrated together using an all-freeze-casting strategy. The continuous seamless connection of such all-in-one ZIBs can avoid displacing and detaching between the electrodes and separator under different bending states and improve the load-transfer capacity and interface strength between the neighboring component layers. As a result, the all-in-one ZIBs show excellent flexibility and superior electrochemical stability under different bending states.

In Situ Incorporation of Pores and Nanoparticles into Polymer Surfaces Using Melt Crystallization

Engineering the surface properties of a material without affecting its bulk properties is desirable for many applications, but it is often not readily achievable because it requires a complex series of processing steps. This study presents for the first time a simple and straightforward method that can convert regular flat polymer surfaces into various porous composite surfaces. The controlled dissolution of the polymer surface by a dispersion and subsequent melt crystallization allows for the successful embedding of dispersed inorganic or organic particles in the pore walls. The porous surface morphology is not significantly affected by the type of dispersed particle, but the contact and sliding angles and surface wettability are. Both superhydrophobic and oil/water separation surfaces can be conveniently fabricated from flat polymer surfaces. This novel and versatile technique could provide engineering freedom for the future development of various functional materials.

Cryostructuring of Polymeric Systems. 52. Properties, Microstructure and an Example of a Potential Biomedical Use of the Wide-Pore Alginate Cryostructurates

Wide-pore cryostructurates were prepared via freezing sodium alginate aqueous solutions with subsequent ice sublimation from the frozen samples, followed by their incubation in the ethanol solutions of calcium chloride or sulfuric acid, rinsing, and final drying. Such sequence of operations resulted in the calcium alginate or alginic acid sponges, respectively. The swelling degree of the walls of macropores in such matrices decreased with increasing polymer concentration in the initial solution. The dependence of the degree of swelling on the cryogenic processing temperature had a bell-like character with a maximum for the samples formed at -20 °C. According to 1H NMR spectroscopy, the content of mobile (non-frozen) water in the frozen water-sodium alginate systems also depended on the initial polymer concentration and freezing temperature. The cryostructurates obtained did not lose their integrity in water, saline, in an acidic medium at pH 2 for at least three weeks. Under alkaline conditions at pH 12 the first signs of dissolution of the Ca-alginate sponge arose only after a week of incubation. Microbiological testing of the model depot form of the antibiotics entrapped in the Ca-alginate cryostructurate demonstrated the efficiency of this system as the antibacterial material.

Electrically assisted 3D printing of nacre-inspired structures with self-sensing capability

Lightweight and strong structural materials attract much attention due to their strategic applications in sports, transportation, aerospace, and biomedical industries. Nacre exhibits high strength and toughness from the brick-and-mortar-like structure. Here, we present a route to build nacre-inspired hierarchical structures with complex three-dimensional (3D) shapes by electrically assisted 3D printing. Graphene nanoplatelets (GNs) are aligned by the electric field (433 V/cm) during 3D printing and act as bricks with the polymer matrix in between as mortar. The 3D-printed nacre with aligned GNs (2 weight %) shows lightweight property (1.06 g/cm³) while exhibiting comparable specific toughness and strength to the natural nacre. In addition, the 3D-printed lightweight smart armor with aligned GNs can sense its damage with a hesitated resistance change. This study highlights interesting possibilities for bioinspired structures, with integrated mechanical reinforcement and electrical self-sensing capabilities for biomedical applications, aerospace engineering, as well as military and sports armors.

Bioinspired nacre-like alumina with a bulk-metallic glass-forming alloy as a compliant phase

Bioinspired ceramics with micron-scale ceramic "bricks" bonded by a metallic "mortar" are projected to result in higher strength and toughness ceramics, but their processing is challenging as metals do not typically wet ceramics. To resolve this issue, we made alumina structures using rapid pressureless infiltration of a zirconium-based bulk-metallic glass mortar that reactively wets the surface of freeze-cast alumina preforms. The mechanical properties of the resulting Al2O3 with a glass-forming compliant-phase change with infiltration temperature and ceramic content, leading to a trade-off between flexural strength (varying from 89 to 800 MPa) and fracture toughness (varying from 4 to more than 9 MPa·m½). The high toughness levels are attributed to brick pull-out and crack deflection along the ceramic/metal interfaces. Since these mechanisms are enabled by interfacial failure rather than failure within the metallic mortar, the potential for optimizing these bioinspired materials for damage tolerance has still not been fully realized.

Plasma-Ice Interface as Thermodynamically Size-Tunable Reaction Field: Development of Plasma-Assisted Freeze Templating

Interfaces or interfacial layers, such as gas-liquid interfaces, are critical for many physical and chemical reactions and are utilized for designing a wide range of materials. In this study, we propose a plasma-assisted freeze templating (PFT) method for materials processing. It uses a new type of interfacial reaction field, i.e., plasma-ice interface. In PFT, a micro- or nanoscale liquid layer formed on the ice body of a frozen aqueous solution is used as a reaction field in which the solutes are highly enriched and the chemical reactions are initiated by reactive species from the plasma. We demonstrated the synthesis of a self-standing gold nanoparticle (AuNP) film of porous structure by PFT in which a helium cryoplasma jet was irradiated onto a frozen solution of auric ions. This PFT method accomplished a surfactant-free and area-selective synthesis of a AuNP film and was unique in comparison with the conventional chemical synthesis of nanostructured gold materials. Furthermore, simple control of the AuNP film was demonstrated by tuning the thickness of the thin liquid layer. This was done by changing the temperature or concentration of the aqueous solution. PFT was demonstrated as a thermodynamically size-tunable scheme for material design; it exploits the plasma-ice interface and is expected to become a novel technique for a wide range of micro- and nanoengineering applications.

Ultralight, superelastic and bendable lashing-structured nanofibrous aerogels for effective sound absorption

Low-density nanofibrous aerogels enable various applications but are often hindered by their fragile bendability and poor tensile strength. Herein, we report a strategy to design nanofibrous aerogels with robust bendability and superelastic property, which has been achieved by fabricating bamboo lashing-like structures through a freeze-drying method. The obtained reinforced nanofibrous aerogels (RNFAs) can maintain their structural integrity after 100 bending-recovery cycles at a bending angle of about 100°. Particularly, the RNFAs can completely revive from large deformation with a fast recovery speed (∼834 mm s-1). Significantly, the internal hierarchical porous structures and hydrophobicity of the materials provide them with ultralight properties (density <11 mg cm-3), efficient sound absorption capability (noise reduction coefficient of 0.41) and good moisture resistance; thus, they are promising options in cabins, vehicles, and the regulation of indoor reverberation.

Directional freezing of binary colloidal suspensions: a model for size fractionation of graphene oxide

The performance of graphene oxide (GO)-based materials strongly depends on the lateral size and size distribution of GO nanosheets. Various methods are employed to prepare GO nanosheets with a narrow size distribution. One promising method was proposed recently, directional freezing of a GO aqueous dispersion at a controlled growth rate of the freezing front. We develop a theoretical model of a binary colloidal suspension, incorporating both the moving freezing boundary and the preferential adsorption of colloidal particles to the ice phase. We numerically solve the coupled diffusion equations and present state diagrams of size fractionation. Selective trapping of colloids according to their size can be achieved by a suitable choice of the experimental parameters, such as the adsorption rates and the freezing speed.

La-Doped biomimetic scaffolds facilitate bone remodelling by synchronizing osteointegration and phagocytic activity of macrophages

The capacity of osteoconduction held by HA/CS, osteoinduction by La³⁺, and biodegradability by a La-HA/CS composite, contributes to an ideal scaffold for osteointegration and remodelling.

Highly porous composite aerogel based triboelectric nanogenerators for high performance energy generation and versatile self-powered sensing

Boosting power generation performance while employing economical and biocompatible materials is an ongoing direction in the field of triboelectric nanogenerators (TENGs). Here, highly porous, biocompatible, cellulose nanofibril (CNF) composite-based TENGs are developed through an environmentally friendly freeze-drying approach. High tribopositivity materials, including silica fiber, human hair, and rabbit fur, are used as fillers in composite TENG fabrication for the first time to enhance the triboelectric output performance. Among them, a CNF/rabbit fur composite aerogel-based TENG offers the optimum energy generation ability with a high power density of 3.4 W m-2 achieved on a 4.7 MΩ load at a pressure of 30 kPa. Owing to the high output, the porous composite TENG exhibits an excellent energy harvesting performance and high sensitivity in detecting ultralight forces and monitoring human motion when used as a self-powered sensor. This work introduces a new class of highly porous composite TENGs that integrate biocompatibility, low cost, flexibility, high energy generation performance, and sensing sensitivity, as well as providing new strategies for high performance TENG design and fabrication.

Anionic Surfactant-Triggered Steiner Geometrical Poly(vinylidene fluoride) Nanofiber/Nanonet Air Filter for Efficient Particulate Matter Removal

The emergence of Steiner minimal tree is of fundamental importance, and designing such geometric structure and developing its application have practical effect in material engineering and biomedicine. We used a cutting-edge nanotechnology, electrospinning/netting, to generate a Steiner geometrical poly(vinylidene fluoride) (PVDF) nanofiber/nanonet filter for removing airborne particulate matter (PM). Manipulation of surface morphologies by precise control of charged situation enabled the creation of two-dimensional nanonets with Steiner geometry. A significant crystalline phase transition of PVDF from α-phase to β-phase was triggered by the dipole orientation and the intermolecular interactions derived from the electrostatic potential analysis. Particularly, the synergy of electrical interaction (ion-dipole and dipole-dipole) and hydrophobic interaction facilitated the formation of Steiner geometric structure during the evolution process of nanonets. The resultant PVDF nanofiber/nanonet air filter exhibited high filtration efficiency of 99.985% and low pressure drop of 66.7 Pa under the airflow velocity of 32 L/min for PM_0.26 removal by the safest physical sieving mechanism. Furthermore, such filter possessed robust structure integrity for reusability, comparable optical transmittance, superior thermal stability, and prominent purification capacity for smoke PM_2.5. The successful construction of such fascinating Steiner geometrical PVDF nanonets will provide new insights into the design and exploitation of novel filter media for air cleaning and haze treatment.

Triboelectric Nanogenerators Made of Porous Polyamide Nanofiber Mats and Polyimide Aerogel Film: Output Optimization and Performance in Circuits

Triboelectric nanogenerators (TENGs) have been attracting a tremendous amount of attention since their discovery in 2012. Finding new means to enhance energy output is an ongoing pursuit. Herein, we introduce a new type of high-performance TENG composed of highly porous polyamide (PA) nanofiber mats and polyimide aerogel films. We have demonstrated that the thickness of the porous triboelectric materials, which is attained by stacking multiple layers of triboelectric materials, has a profound effect on the triboelectric output performance of TENGs. The triboelectric output increased when PA increased from one layer to six layers. However, it decreased when PA was further increased to 12 layers. With an optimum material thickness, a TENG with only a 2 cm² effective device size achieved a high output voltage of 115 V and a current of 9.5 μA under a small compressive pressure (30 kPa). A peak power density of 1.84 W/m² was achieved on a 4.7 MΩ external load. The TENG was able to light 60 light-emitting diodes easily and quickly charge capacitors with different capacitance to 6 V, indicating an outstanding energy harvesting ability. In addition, the performance of multiple TENGs connected in different ways, as well as the performance of TENGs in resistive/inductive/capacitive circuits, were investigated. These findings provide new insight into the working principles of TENGs in complex circuits.

Cryostructuring of Polymeric Systems. 50.† Cryogels and Cryotropic Gel-Formation: Terms and Definitions

A variety of cryogenically-structured polymeric materials are of significant scientific and applied interest in various areas. However, in spite of considerable attention to these materials and intensive elaboration of their new examples, as well as the impressive growth in the number of the publications and patents on this topic over the past two decades, a marked variability of the used terminology and definitions is frequently met with in the papers, reviews, theses, patents, conference presentations, advertising materials and so forth. Therefore, the aim of this brief communication is to specify the basic terms and definitions in the particular field of macromolecular science.

Hexamethylcucurbit[3,3]uril-Based Porous Supramolecular Assemblies and Their Adsorption Properties

In the present work, we selected hexamethylcucurbit[3,3]uril (Me6Q[3,3]) as a building block and obtained two Me6Q[3,3]-based porous supramolecular assemblies from neutral water (A) and aqueous HCl solutions (B), respectively. Both Me6Q[3,3]-based assemblies are constructed of Me6Q[3,3] molecules through the typical outer surface interaction of cucurbit[n]urils, as well as hydrogen bonding between latticed water molecules and portal carbonyl oxygens of Me6Q[3,3]. The assemblies present different porous structure features and exhibit different adsorption properties for eight common volatile organic compounds. However, the two porous assemblies exhibit similar adsorption properties for certain fluorophore dyes, including rhodamine B (G1), fluorescein (G2), and pyrene (G3), and form solid colored fluorescent compounds, some of which exhibit responses to the selected volatile organic compounds.

An All-Freeze-Casting Strategy to Design Typographical Supercapacitors with Integrated Architectures

The emergence of flexible and wearable electronics has raised the demand for flexible supercapacitors with accurate sizes and aesthetic shapes. Here, a strategy is developed to prepare flexible all-in-one integrated supercapacitors by combining all-freeze-casting with typography technique. The continuous seamless connection of all-in-one supercapacitor devices enhances the load and/or electron transfer capacity and avoids displacing and detaching between their neighboring components at bending status. Therefore, such a unique structure of all-in-one integrated devices is beneficial for retaining stable electrochemical performance at different bending levels. More importantly, the sizes and aesthetic shapes of integrated supercapacitors could be controlled by the designed molds, like type matrices of typography. The molds could be assembled together and typeset randomly, achieving the controllable construction and series and/or parallel connection of several supercapacitor devices. The preparation of flexible integrated supercapacitors will pave the way for assembling programmable all-in-one energy storage devices into highly flexible electronics.