Dry powder inhalation: past, present and future

Characterization of dry powder inhaler performance through experimental methods

Experimental methods provide means for the quality control of existing DPIs and for exploring the influence of formulation and device parameters well in advance of clinical trials for novel devices and formulations. In this review, we examine the state of the art of in vitro testing of DPIs, with a focus primarily on the development of accurate in vitro-in vivo correlations. Aspects of compendial testing are discussed, followed by the influence of flow profiles on DPI performance, the characterization of extrathoracic deposition using mouth-throat geometries, and the characterization of regional thoracic deposition. Additional experimental methods that can inform the timing of bolus delivery, the influence of environmental conditions, and the development of electrostatic charge on aerosolized DPI powders are reviewed. We conclude with perspectives on current in vitro methods and identify potential areas for future investigation, including the estimation of variability in deposition, better characterization of existing compendial methods, optimization of formulation and device design to bypass extrathoracic deposition, and the use of novel tracheobronchial filters that aim to provide more clinically relevant measures of performance directly from in vitro testing.

Modelling Deaggregation Due to Normal Carrier–Wall Collision in Dry Powder Inhalers

Powder deaggregation in Dry Powder Inhalers (DPI) with carrier-based formulations is a key process for the effectiveness of drug administration. Carrier-wall collisions are one of the recognised mechanisms responsible for active pharmaceutical ingredient (API) aerosolisation, and DPI geometries are designed to maximise their efficacy. The detachment of fine and cohesive API particles is investigated at a fundamental level by simulating with DEM the normal collision of a carrier sphere with an API particle attached. The impact velocity at which detachment occurs (escape velocity) is determined as a function of key parameters, such as cohesiveness, coefficient of restitution, static and rolling friction. An analytical model for the escape velocity is then derived, examining the role of the initial position of the particle, cohesion model and particle size. Finally, the results are framed in the context of DPI inhalers, comparing the results obtained with impact velocities typically recorded in commercial devices.

Dry powder inhalation, part 2: the present and future

INTRODUCTION

The manufacture of modern dry powder inhalers (DPIs), starting with the Spinhaler (Fisons) in 1967, was only possible thanks to a series of technological developments in the 20^th century, of which many started first around 1950. Not until then, it became possible to design and develop effective, cheap and mass-produced DPIs. The link between these technological developments and DPI development has never been presented and discussed before in reviews about the past and present of DPI technology.

AREAS COVERED

The diversity of currently used DPIs with single dose, multiple-unit dose and multi-dose DPIs is discussed, including the benefits and drawbacks of this diversity for correct use and the efficacy of the therapy. No specific databases or search engines otherwise than PubMed and Google have been used.

EXPERT OPINION

Considering the relatively poor efficacy regarding lung deposition of currently used DPIs, the high rates of incorrect inhaler use and inhalation errors and the poor adherence to the therapy with inhalers, much effort must be put in improving these shortcomings for future DPI designs. Delivered fine particle doses must be increased, correct inhaler handling must become more intuitive and simpler to perform, and the use of multiple inhalers must be avoided.

Dry powder inhalation, part 1: ancient history and precursors to modern dry powder inhalers

INTRODUCTION

Inhalation of herbs and other compounds has a long history but habits for medical treatment are intertwined with rituals to obtain hallucinatory effects and pleasurable sensations. Several examples of inhaled herbs, and the diseases they were used for, based on early translations of ancient manuscripts related to inhalation were found to be speculative and inconsistent with each other in literature. They needed to be reconsidered and verified with the original sources of information.

AREAS COVERED

Examples of ancient inhalation and the development of early dry powder inhalers up to and including the first half of the twentieth century. Databases used for literature about historic events, ancient habits, and ancient science, included SmartCat, JSTOR, and ANDAT; various facts were verified via personal communication with historians and custodians of historic manuscripts and artifacts.

EXPERT OPINION

Inhalation does not necessarily require active creation of inhalable aerosols, smokes or fumes. Inhaling 'healthy air' with volatile and gaseous components, or fine aerosols in pine forests, on volcano slopes and at the seaside must be considered as inhalation therapy too. From this viewpoint, inhalation therapy may have been much more common and widespread and have a longer history than is currently known from written evidence.

Micro-fluidic Spray Freeze Dried Ciprofloxacin Hydrochloride-Embedded Dry Powder for Inhalation

Active pharmaceutical ingredient (API)-embedded dry powder for inhalation (AeDPI) is highly desirable for pulmonary delivery of high-dose drug. Herein, a series of spray freeze-dried (SFD) ciprofloxacin hydrochloride (CH)-embedded dry powders were fabricated via a self-designed micro-fluidic spray freeze tower (MFSFT) capable of tuning freezing temperature of cooling air as the refrigerant medium. The effects of total solid content (TSC), mass ratio of CH to _L-leucine (Leu) as the aerosol dispersion enhancer, and the freezing temperature on particle morphology, size, density, moisture content, crystal properties, flowability, and aerodynamic performance were investigated. It was found that the Leu content and freezing temperature had considerable influence on the fine particle fraction (FPF) of the SFD microparticles. The optimal formulation (CH/Leu = 7:3, TSC = 2%w/w) prepared at - 40°C exhibited remarkable effective drug deposition (~ 33.38%), good aerodynamic performance (~ 47.69% FPF), and excellent storage stability with ultralow hygroscopicity (~ 1.93%). This work demonstrated the promising feasibility of using the MFSFT instead of conventional liquid nitrogen assisted method in the research and development of high-dose AeDPI.

Recent developments in the computational simulation of dry powder inhalers

This article reviews recent developments in computational modeling of dry powder inhalers (DPIs). DPIs deliver drug formulations (sometimes blended with larger carrier particles) to a patient's lungs via inhalation. Inhaler design is complicated by the need for maximum aerosolization efficiency, which is favored by high levels of turbulence near the mouthpiece, with low extrathoracic depositional loss, which requires low turbulence levels near the mouth-throat region. In this article, we review the physical processes contributing to aerosolization and subsequent dispersion and deposition. We assess the performance characteristics of DPIs using existing simulation techniques and offer a perspective on how such simulations can be improved to capture the physical processes occurring over a wide range of length- and timescales more efficiently.

Dry powder inhalers of antitubercular drugs

Despite advancements in the medical and pharmaceutical fields, tuberculosis remains a major health problem globally. Patients do not widely accept the conventional approach to treating tuberculosis (TB) due to prolonged treatment periods with multiple high doses of drugs and associated side effects. A pulmonary route is a non-invasive approach to delivering drugs, hormones, nucleic acid, steroids, proteins, and peptides directly to the lungs, improving the efficacy of the treatment and consequently decreasing the adverse effect of the treatment. This route has been successfully developed for the treatment of various respiratory diseases such as asthma, chronic obstructive pulmonary disease (COPD), tuberculosis (TB), lung cancer, and other pulmonary infections. The major approaches of inhalation delivery systems include nebulizers, metered-dose inhalers (MDIs), and dry powder inhalers (DPIs). However, dry powder inhalers (DPIs) are more advantageous due to their stability and ability to deliver a high dose of the drug to the lungs. The present review analyzes the modern therapeutic approach of inhaled dry powders, with a special focus on novel drug delivery system (NDDS) based DPIs for the treatment of TB. The article also discussed the challenges of preparing inhalable dry powder formulations for the treatment of TB. The clinical development of inhalable anti-TB drugs is also reviewed.

The history, current state and perspectives of aerosol therapy

Nebulization is a very effective method of drug administration. This technique has been popular since ancient times when inhalation of plants rich in tropane alkaloids with spasmolytic and analgesic effects was widely used. Undoubtedly, the invention of anasthesia in the 19th century had an influence on the development of this technique. It resulted in the search for devices that facilitated anasthesia such as pulveriser or hydronium. From the second half of the 21st century, when the first DPI and MDI inhalers were launched, the constant development of aerosol therapy has been noticed. This is due to the fact that nebulization, compared with other means of medicinal substance application (such as oral and intravenous routes of administration), is safer and it exhibits a positive dose/efficacy ratio connected to the reduction of the dose. It enables drugs administration through the lung and possesses very fast onset action. Therefore, various drugs prescribed in respiratory diseases (such as corticosteroids, β-agonists, anticholinergics) are present on the market in a form of an aerosol.

Spray-dried Pneumococcal Membrane Vesicles are Promising Candidates for Pulmonary Immunization

Pneumococcal infections represent a global health threat, which requires novel vaccine developments. Extracellular vesicles are secreted from most cells, including prokaryotes, and harbor virulence factors and antigens. Hence, bacterial membrane vesicles (MVs) may induce a protective immune response. For the first time, we formulate spray-dried gram-positive pneumococcal MVs-loaded vaccine microparticles using lactose/leucine as inert carriers to enhance their stability and delivery for pulmonary immunization. The optimized vaccine microparticles showed a mean particle size of 1-2µm, corrugated surface, and nanocrystalline nature. Their aerodynamic diameter of 2.34µm, average percentage emitted dose of 88.8%, and fine powder fraction 79.7%, demonstrated optimal flow properties for deep alveolar delivery using a next-generation impactor. Furthermore, confocal microscopy confirmed the successful encapsulation of pneumococcal MVs within the prepared microparticles. Human macrophage-like THP-1 cells displayed excellent viability, negligible cytotoxicity, and a rapid uptake around 60% of fluorescently labeled MVs after incubation with vaccine microparticles. Moreover, vaccine microparticles increased the release of pro-inflammatory cytokines tumor necrosis factor and interleukin-6 from primary human peripheral blood mononuclear cells. Vaccine microparticles exhibited excellent properties as promising vaccine candidates for pulmonary immunization and are optimal for further animal testing, scale-up and clinical translation.

Mixing of dry powders for inhalation: A review

The process of solids mixing is applied across a considerable range of industries. Pharmaceutical science is one of those industries that utilizes solids mixing extensively. Specifically, solids mixing as a key factor in the preparation of dry powder inhalers using the ordered mixing process will be discussed here. This review opens with a history of dry powder mixing theory, continues to ordered mixing in the preparation for dry powder inhalers, details key interparticulate interactions, explains formulation components for dry powder blends, and finally discusses different types of mixers used in the production of dry powder blends for inhalation. Lastly, the authors offer some suggestions for future work on this topic.

Spray Dried Rugose Lipid Particle Platform for Respiratory Drug Delivery

PURPOSE

To develop a new lipid-based particle formulation platform for respiratory drug delivery applications. To find processing conditions for high surface rugosity and manufacturability. To assess the applicability of the new formulation method to different lipids.

METHODS

A new spray drying method with a simplified aqueous suspension feedstock preparation process was developed for the manufacture of rugose lipid particles of 1,2-distearoyl-sn-glycero-3-phosphocholine (DSPC). A study covering a wide range of feedstock temperatures and outlet temperatures was conducted to optimize the processing conditions. Aerosol performance was characterized in vitro and in silico to assess the feasibility of their use in respiratory drug delivery applications. The applicability of the new spray drying method to longer-chain phospholipids with adjusted spray drying temperatures was also evaluated.

RESULTS

Highly rugose DSPC lipid particles were produced via spray drying with good manufacturability. A feedstock temperature close to, and an outlet temperature lower than, the main phase transition were identified as critical in producing particles with highly rugose surface features. High emitted dose and total lung dose showed promising aerosol performance of the produced particles for use as a drug loading platform for respiratory drug delivery. Two types of longer-chain lipid particles with higher main phase transition temperatures, 1,2-diarachidoyl-sn-glycero-3-phosphocholine (DAPC) and 1,2-dibehenoyl-sn-glycero-3-phosphocholine (22:0 PC), yielded similar rugose morphologies when spray dried at correspondingly higher processing temperatures.

CONCLUSIONS

Rugose lipid particles produced via spray drying from an aqueous suspension feedstock are promising as a formulation platform for respiratory drug delivery applications. The new technique can potentially produce rugose particles using various other lipids.

Salvianolic acid B dry powder inhaler for the treatment of idiopathic pulmonary fibrosis

Idiopathic pulmonary fibrosis (IPF) is a serious and fatal pulmonary inflammatory disease with an increasing incidence worldwide. The drugs nintedanib and pirfenidone, are listed as conditionally recommended drugs in the “Evidence-Based Guidelines for the Diagnosis and Treatment of Idiopathic Pulmonary Fibrosis”. However, these two drugs have many adverse reactions in clinical application. Salvianolic acid B (Sal B), a water-soluble component of Salvia miltiorrhiza, could alleviate bleomycin-induced peroxidative stress damage, and prevent or delay the onset of IPF by regulating inflammatory factors and fibrotic cytokines during the disease's progression. However, Sal B is poorly absorbed orally, and patient compliance is poor when administered intravenously. Therefore, there is an urgent need to find a new non-injection route of drug delivery. In this study, Sal B was used as model drug and l-leucine (LL) as excipient to prepare Sal B dry powder inhaler (Sal B-DPI) by spray drying method. Modern preparation evaluation methods were used to assess the quality of Sal B-DPI. Sal B-DPI is promising for the treatment of IPF, according to studies on pulmonary irritation evaluation, in vivo and in vitro pharmacodynamics, metabolomics, pharmacokinetics, and lung tissue distribution.

Novel Thymoquinone Nanoparticles Using Poly(ester amide) Based on L-Arginine-Targeting Pulmonary Drug Delivery

Thymoquinone (TQ), the main active constituent of Nigella sativa, has demonstrated broad-spectrum antimicrobial, antioxidant, and anti-inflammatory effects, which suggest its potential use in secondary infections caused by COVID-19. However, clinical deployment has been hindered due to its limited aqueous solubility and poor bioavailability. Therefore, a targeted delivery system to the lungs using nanotechnology is needed to overcome limitations encountered with TQ. In this project, a novel TQ-loaded poly(ester amide) based on L-arginine nanoparticles was prepared using the interfacial polycondensation method for a dry powder inhaler targeting delivery of TQ to the lungs. The nanoparticles were characterized by FTIR and NMR to confirm the structure. Transmission electron microscopy and Zetasizer results confirmed the particle diameter of 52 nm. The high-dose formulation showed the entrapment efficiency and loading capacity values of TQ to be 99.77% and 35.56%, respectively. An XRD study proved that TQ did not change its crystallinity, which was further confirmed by the DSC study. Optimized nanoparticles were evaluated for their in vitro aerodynamic performance, which demonstrated an effective delivery of 22.7–23.7% of the nominal dose into the lower parts of the lungs. The high drug-targeting potential and efficiency demonstrates the significant role of the TQ nanoparticles for potential application in COVID-19 and other respiratory conditions.

Novel Fluticasone Propionate and Salmeterol Fixed-Dose Combination Nano-Encapsulated Particles Using Polyamide Based on L-Lysine

One of the key challenges in developing a dry powder inhaler (DPI) of an inhalable potent fixed-dose combination (FDC) is the ability of the formulation to generate an effective and reproducible aerosol able to reach the lower parts of the lungs. Herein, a one-step approach is presented to expedite the synthesis of nanoaggregates made from a biocompatible and biodegradable polyamide based on L-lysine amino acid employing market-leading active pharmaceutical ingredients (fluticasone propionate (FP) and salmeterol xinafoate (SAL)) for the management of asthma. The nanoaggregates were synthesized using interfacial polycondensation that produced nanocapsules with an average particle size of 226.7 ± 35.3 nm and zeta potential of -30.6 ± 4.2 mV. Differential scanning calorimetric analysis and x-ray diffraction, as well as scanning electron microscopy of the produced FDC, revealed the ability of the produced nanocapsules to encapsulate the two actives and display the best aerodynamic performance. The FDC nanocapsules displayed 88.5% and 98.5% of the emitted dose for FP and SAL, respectively. The fine particle fraction of the nominated dose was superior to the marketed product (Seretide Diskus®, Brentford, United Kingdom). The in-vitro release study showed an extended drug release profile. Our findings suggest that nanoaggregates using polyamides based on L-lysine and interfacial polycondensation can serve as a good platform for pulmonary drug delivery of FDC systems.

A roadmap to pulmonary delivery strategies for the treatment of infectious lung diseases

Pulmonary drug delivery is a highly attractive topic for the treatment of infectious lung diseases. Drug delivery via the pulmonary route offers unique advantages of no first-pass effect and high bioavailability, which provides an important means to deliver therapeutics directly to lung lesions. Starting from the structural characteristics of the lungs and the biological barriers for achieving efficient delivery, we aim to review literatures in the past decade regarding the pulmonary delivery strategies used to treat infectious lung diseases. Hopefully, this review article offers new insights into the future development of therapeutic strategies against pulmonary infectious diseases from a delivery point of view.

Effect of pressure drop on the in vitro dispersion of adhesive mixtures of different blend states for inhalation

In this study, the effect of pressure drop (ΔP) on the in vitro dispersion of a series of carrier-based adhesive mixtures of different fines-to-carrier proportions, corresponding to the four different blend states of the blend state model, i.e. S1 to S3, was investigated. Four binary and one ternary adhesive mixture consisting of lactose carrier and budesonide fines and lactose fines were prepared. The dispersion was assessed using a next generation impactor (NGI) at ΔP of 0.5, 2 and 4 kPa. For the S1 mixture, where the fines were located in surface cavities of the carrier, the fine particle fraction (FPF) increased nearly linearly with ΔP. For S2 and S3 mixtures, with adhesion layers on the enveloped carrier surface, the FPF-ΔP relationships were bended and approached a plateau. Examination of powder captured in the pre-separator of the NGI led to the conclusion that the dispersion of these adhesive mixtures occurred by erosion of the adhesion layer, i.e. budesonide was liberated as single particles or micro-agglomerates. It is concluded that the FPF-ΔP relationships were dependent on the blend state and for the S2 and S3 mixtures, a critical pressure drop was identified above which the pressure drop had a limited effect on the FPF.

Spray Drying and Particle Engineering in Dosage Form Design for Global Vaccines

Vaccines are a very important tool in the effort to reduce the global burden of infectious diseases. Modern vaccines can be formulated in several ways to induce specific immunity, including through the use of live bacteria, subunit antigens, and even genetic material. However, vaccines typically need to be transported and stored under controlled refrigerated or frozen conditions to maintain potency. This strict temperature control is incompatible with the available infrastructure in many developing countries. One method of improving the thermostability of a vaccine is through drying of a liquid presentation into a dry dosage form. In addition to enhancing the capability for distribution in resource-poor settings, these dry vaccine forms are more suitable for long-term stockpiling. Spray drying is a drying method that has been successfully used to stabilize many experimental vaccines into a dry form for storage above refrigerated temperatures. Additionally, the use of spray drying allows for the production of engineered particles suitable for respiratory administration. These particles can be further designed for increased out-of-package robustness against high humidity. Furthermore, there are already commercial dry powder delivery devices available that can be used to safely deliver vaccines to the respiratory system. The research in this field demonstrates that the resources to develop highly stable vaccines in flexible dosage forms are available and that these presentations offer many advantages for global vaccination campaigns.

Combining experimental and computational techniques to understand and improve dry powder inhalers

INTRODUCTION

: Dry Powder Inhalers (DPIs) continue to be developed to deliver an expanding range of drugs to treat an ever-increasing range of medical conditions; with each drug and device combination needing a specifically designed inhaler. Fast regulatory approval is essential to be first to market, ensuring commercial profitability.

AREAS COVERED

: In vitro deposition, particle image velocimetry, and computational modelling using the physiological geometry and representative anatomy can be combined to give complementary information to determine the suitability of a proposed inhaler design and to optimise its formulation performance. In combination they allow the entire range of questions to be addressed cost-effectively and rapidly.

EXPERT OPINION

: Experimental techniques and computational methods are improving rapidly, but each needs a skilled user to maximize results obtained from these techniques. Multidisciplinary teams are therefore key to making optimal use of these methods and such qualified teams can provide enormous benefits to pharmaceutical companies to improve device efficacy and thus time to market. There is already a move to integrate the benefits of Industry 4.0 into inhaler design and usage, a trend that will accelerate.

Inhaled Medicines: Past, Present, and Future

The purpose of this review is to summarize essential pharmacological, pharmaceutical, and clinical aspects in the field of orally inhaled therapies that may help scientists seeking to develop new products. After general comments on the rationale for inhaled therapies for respiratory disease, the focus is on products approved approximately over the last half a century. The organization of these sections reflects the key pharmacological categories. Products for asthma and chronic obstructive pulmonary disease include β -2 receptor agonists, muscarinic acetylcholine receptor antagonists, glucocorticosteroids, and cromones as well as their combinations. The antiviral and antibacterial inhaled products to treat respiratory tract infections are then presented. Two "mucoactive" products-dornase α and mannitol, which are both approved for patients with cystic fibrosis-are reviewed. These are followed by sections on inhaled prostacyclins for pulmonary arterial hypertension and the challenging field of aerosol surfactant inhalation delivery, especially for prematurely born infants on ventilation support. The approved products for systemic delivery via the lungs for diseases of the central nervous system and insulin for diabetes are also discussed. New technologies for drug delivery by inhalation are analyzed, with the emphasis on those that would likely yield significant improvements over the technologies in current use or would expand the range of drugs and diseases treatable by this route of administration. SIGNIFICANCE STATEMENT: This review of the key aspects of approved orally inhaled drug products for a variety of respiratory diseases and for systemic administration should be helpful in making judicious decisions about the development of new or improved inhaled drugs. These aspects include the choices of the active ingredients, formulations, delivery systems suitable for the target patient populations, and, to some extent, meaningful safety and efficacy endpoints in clinical trials.

A real-time and modular approach for quick detection and mechanism exploration of DPIs with different carrier particle sizes

Dry powder inhalers (DPIs) had been widely used in lung diseases on account of direct pulmonary delivery, good drug stability and satisfactory patient compliance. However, an indistinct understanding of pulmonary delivery processes (PDPs) hindered the development of DPIs. Most current evaluation methods explored the PDPs with over-simplified models, leading to uncompleted investigations of the whole or partial PDPs. In the present research, an innovative modular process analysis platform (MPAP) was applied to investigate the detailed mechanisms of each PDP of DPIs with different carrier particle sizes (CPS). The MPAP was composed of a laser particle size analyzer, an inhaler device, an artificial throat and a pre-separator, to investigate the fluidization and dispersion, transportation, detachment and deposition process of DPIs. The release profiles of drug, drug aggregation and carrier were monitored in real-time. The influence of CPS on PDPs and corresponding mechanisms were explored. The powder properties of the carriers were investigated by the optical profiler and Freeman Technology four powder rheometer. The next generation impactor was employed to explore the aerosolization performance of DPIs. The novel MPAP was successfully applied in exploring the comprehensive mechanism of PDPs, which had enormous potential to be used to investigate and develop DPIs.

Engineered-inhaled particles: Influence of carbohydrates excipients nature on powder properties and behavior

Pulmonary drug administration has long been used for local or systemic treatment due to several advantages. Dry powder inhalers emerge as the most promising due to efficiency, ecologic, and drug stability concerns. Coarse lactose-carrier is still the gold standard when inhalation powders are developed. Despite some efforts to produce new types of powders, the lung drug deposition is still poorly controlled, which will ultimately impact therapeutic effectiveness. In this study, we developed "engineered-inhalation powders" using the spray-drying technique. Multiple carbohydrates excipients were binary mixed and combined with two active pharmaceutical ingredients for asthma therapy (budesonide and formoterol). Particle morphology, from spherical to deflated shapes, was characterized by the number and the depth of dimples measured from SEM images. We define a new characteristic deflation ratio ξ as the product between the number of dimples and their depth. Six different powders having opposite morphologies have been selected and we have demonstrated a linear correlation between the fine particle fraction and the deflation ratio of produced powders. Overall, we showed first that the morphology of inhalable powder can be finely tuned by spray-drying technique when excipients varied. Secondly, we developed stable inhalation powders that simultaneously induced high fine particle fractions (>40%) for two drugs due to their deflated surface. The stability has been evaluated for up to 2 months at room temperature.

Nanoparticles for local delivery of siRNA in lung therapy

An overview of the application of natural and synthetic, non-viral vectors for oligonucleotide delivery into the lung is presented in this review, with a special focus on lung cancer. Due to the specificity of the respiratory tract, its structure and natural barriers, the administration of drugs (especially those based on nucleic acids) is a particular challenge. Among widely tested non-viral drug and oligonucleotides carriers, synthetic polymers seem to be most promising. Unique properties of these nanoparticles allow for essentially unlimited possibilities regarding their design and modification. This gives hope that optimal nanoparticles with ideal nucleic acid carrier properties for lung cancer therapy will eventually emanate.

Improving the risk-to-benefit ratio of inhaled corticosteroids through delivery and dose: current progress and future directions

INTRODUCTION

Inhaled corticosteroids (ICS) are known to increase the risk of systemic and local adverse effects, especially with high doses and long-term use. Hence, considerable resources are invested to improve pharmacokinetic/pharmacodynamic (PK/PD) properties of ICS, effective delivery systems and novel combination therapies to enhance the risk-to-benefit ratio of ICS.

AREAS COVERED

There is an unmet need for new solutions to achieve optimal clinical outcomes with minimal dose of ICS. This paper gives an overview of novel treatment strategies regarding the safety of ICS therapy on the basis of the three most recent molecules introduced to our everyday clinical practice - ciclesonide, mometasone furoate, and fluticasone furoate. Advances in aerosol devices and new areas of inhalation therapy are also discussed.

EXPERT OPINION

Current progress in improving the risk-to-benefit ratio of ICS through dose and delivery probably established pathways for further developments. This applies both to the improvement of the PK/PD properties of ICS molecules but also includes technical aspects that lead to simplified applicability of the device with simultaneous optimal drug deposition in the lungs. Indubitably, the future of medicine lies not only in the development of new molecules but also in technology and digital revolution.

Understanding the Importance of Capsules in Dry Powder Inhalers

Pulmonary drug delivery is currently the focus of research and development because of its potential to produce maximum therapeutic benefit to patients by directing the drug straight to the lung disease site. Among all the available delivery options, one popular, proven and convenient inhaler device is the capsule-based dry powder inhaler (cDPI) for the treatment of an increasingly diverse range of diseases. cDPIs use a hard capsule that contains a powder formulation which consists of a mixture of a micronized drug and a carrier usually the lactose, known for its good lung tolerance. The capsule is either inserted into the device during manufacturer or by the patient prior to use. After perforating, opening or cut the capsule in the device, patients take a deep and rapid breath to inhale the powder, using air as the vector of drug displacement. The system is simple, relatively cheap and characterized by a lower carbon footprint than that of pressurized metered dose inhalers. This article reviews cDPI technology, focusing particularly on the importance of capsule characteristics and their function as a drug reservoir in cDPIs.

Inhalable Microparticles Embedding Calcium Phosphate Nanoparticles for Heart Targeting: The Formulation Experimental Design

Inhalation of Calcium Phosphate nanoparticles (CaPs) has recently unmasked the potential of this nanomedicine for a respiratory lung-to-heart drug delivery targeting the myocardial cells. In this work, we investigated the development of a novel highly respirable dry powder embedding crystalline CaPs. Mannitol was selected as water soluble matrix excipient for constructing respirable dry microparticles by spray drying technique. A Quality by Design approach was applied for understanding the effect of the feed composition and spraying feed rate on typical quality attributes of inhalation powders. The in vitro aerodynamic behaviour of powders was evaluated using a medium resistance device. The inner structure and morphology of generated microparticles were also studied. The 1:4 ratio of CaPs/mannitol led to the generation of hollow microparticles, with the best aerodynamic performance. After microparticle dissolution, the released nanoparticles kept their original size.

Dry powder inhaler formulation comparison: Study of the role of particle deposition pattern and dissolution

The composition, morphology and dissolution profile of particles and micro-sized agglomerates delivered upon inhalation may have a significant impact on the product clinical effect. However, although several efforts are ongoing, a methodology that considers deposition structures and dissolution performance evaluation in a biorelevant set-up is not yet standardized. The goal of this work is to apply a collection and dissolution methodology able to discriminate dry powder inhaler (DPI) formulations in terms of deposition structures and dissolution profile in vitro. Hence, Fluticasone Propionate (FP) engineered particles and formulated products (used as a case study) were collected employing a breath simulator and characterized regarding (i) aerodynamic particle size distribution; (ii) deposited microstructures; and (iii) dissolution/absorption profiles using the DissolvIt® bio-relevant dissolution equipment. The results indicated that the particle engineering technology had an impact on the generated and deposited microstructures, here associated to the differences on surface properties of jet milled and wet polished particles quantified by the specific surface area. Differences on surface properties modulate particle interactions, resulting in agglomerates of drug substance and excipient upon actuation with significant different morphologies, observed by microscope, as well as quantified by Marple cascade impactor. These observations allow for a further understanding of the DPI aerosolization and deposition mechanisms. The dissolution and absorption assessment indicates that the presence of lactose may accelerate the drug substance dissolution kinetics, and the FP dissolution can be significantly enhanced when formulated as a spray-dried dispersion particle. Ultimately, the results suggest dissolution testing can be an essential tool to both optimize an innovator DPI and de-risk generics development.

Dry Powder Inhalers in the Digitalization Era: Current Status and Future Perspectives

During the last decades, the term "drug delivery systems" (DDSs) has almost fully replaced previously used terms, such as "dosage forms", in an attempt to emphasize the importance of the drug carrier in ensuring the claimed safety and effectiveness of the product. However, particularly in the case of delivery devices, the term "system", which by definition implies a profound knowledge of each single part and their interactions, is not always fully justified when using the DDS term. Within this context, dry powder inhalers (DPIs), as systems to deliver drugs via inhalation to the lungs, require a deep understanding of the complex formulation-device-patient interplay. As of now and despite the progress made in particle engineering and devices design, DPIs' clinical performance is limited by variable patients' breathing patterns. To circumvent this pitfall, next-generation DPIs should ideally adapt to the different respiratory capacity of individuals across age, health conditions, and other related factors. In this context, the recent wave of digitalization in the health care and industrial sectors may drive DPI technology towards addressing a personalized device-formulation-patient liaison. In this review, evolving technologies are explored and analyzed to outline the progress made as well as the gaps to fill to align novel DPIs technologies with the systems theory approach.

A technology evaluation of CVT-301 (Inbrija): an inhalable therapy for treatment of Parkinson's disease

Introduction: The most widely used pharmacological treatment for Parkinson's disease is levodopa, the precursor for dopamine formation in the brain. Over time, the effectiveness of levodopa declines, and patients experience motor fluctuations, or OFF periods. A levodopa formulation administered via a capsule-based oral inhaler provides a new delivery mechanism for levodopa that provides rapid relief of OFF periods.Areas covered: CVT-301 is a dry powder formulation designed to supply levodopa to the systemic circulation via pulmonary absorption. The technology, pharmacokinetics, efficacy, and safety data of this formulation are presented.Expert opinion: Oral inhalation is a novel method of administration for levodopa that bypasses the gastrointestinal tract, allowing levodopa to enter the systemic circulation rapidly and more reliably than oral medications. Gastrointestinal dysfunction, a common feature of Parkinson's disease, can lead to impaired absorption of oral medications. Pulmonary delivery rapidly elevates levodopa plasma concentrations to provide relief of OFF periods for patients receiving oral levodopa.

Improved Bioavailability with Dry Powder Cannabidiol Inhalation: A Phase 1 Clinical Study

Oral cannabidiol (CBD) is approved by the Food and Drug Administration (FDA) to treat patients with Dravet and Lennox-Gastaut syndromes, and tuberous sclerosis complex. The therapeutic potential of oral CBD formulations is limited by extensive first-pass hepatic metabolism. Following oral administration, the inactive metabolite blood concentration is ∼40-fold higher than CBD. Inhalation bypasses the pharmacokinetic (PK) variability attributed to irregular gastrointestinal absorption and first-pass hepatic metabolism and may efficiently deliver CBD into systemic circulation. This phase 1 study compared the PK of a dry-powder inhaler (DPI) CBD formulation (10 mg; excipient containing 2.1 mg CBD) with an oral CBD solution (Epidiolex®, 50 mg) in healthy participants. Following a single dose of Epidiolex or DPI CBD (n=10 PK evaluable participants each), the maximum CBD concentration for the inhaled powder was 71-fold higher than that of Epidiolex while administering 24-fold less CBD. The mean time to reach maximum concentration was 3.8 minutes for the DPI CBD formulation compared with 122 minutes for Epidiolex. Both Epidiolex and DPI CBD were generally safe and well-tolerated. These data indicate that DPI CBD provided more rapid onset and increased bioavailability than oral CBD and support further investigations on the use of DPI CBD for acute indications.

A Quality by Design Framework for Capsule-Based Dry Powder Inhalers

Capsule-based dry powder inhalers (cDPIs) are widely utilized in the delivery of pharmaceutical powders to the lungs. In these systems, the fundamental nature of the interactions between the drug/formulation powder, the capsules, the inhaler device, and the patient must be fully elucidated in order to develop robust manufacturing procedures and provide reproducible lung deposition of the drug payload. Though many commercially available DPIs utilize a capsule-based dose metering system, an in-depth analysis of the critical factors associated with the use of the capsule component has not yet been performed. This review is intended to provide information on critical factors to be considered for the application of a quality by design (QbD) approach for cDPI development. The quality target product profile (QTPP) defines the critical quality attributes (CQAs) which need to be understood to define the critical material attributes (CMA) and critical process parameters (CPP) for cDPI development as well as manufacturing and control.

Evaluation of sex-based differences in airway size and the physiological implications

Recent evidence suggests healthy females have significantly smaller central conducting airways than males when matched for either height or lung volume during analysis. This anatomical sex-based difference could impact the integrative response to exercise. Our review critically evaluates the literature on direct and indirect techniques to measure central conducting airway size and their limitations. We present multiple sources highlighting the difference between male and female central conducting airway size in both pediatric and adult populations. Following the discussion of measurement techniques and results, we discuss the functional implications of these differences in central conducting airway size, including work of breathing, oxygen cost of breathing, and how these impacts will continue into elderly populations. We then discuss a range of topics for the future direction of airway differences and the benefits they could provide to both healthy and diseased populations. Specially, these sex-differences in central conducting airway size could result in different aerosol deposition or how lung disease manifests. Finally, we detail emerging techniques that uniquely allow for high-resolution imaging to be paired with detailed physiological measures.

Nasal Spray Formulations Based on Combined Hyalurosomes and Glycerosomes Loading Zingiber officinalis Extract as Green and Natural Strategy for the Treatment of Rhinitis and Rhinosinusitis

A total green nanotechnological nasal spray has been manufactured and proposed as an alternative treatment of rhinitis and rhinosinusitis. It was obtained by combining the strengthening effect of liposomes on barrier function, the hydrating and lubricating properties of sodium hyaluronan and the anti-inflammatory and antioxidant activities of the extract of Zingiber officinalis. To this purpose, the extract was loaded in special phospholipid vesicles immobilized with hyaluronic acid (hyalurosomes), which were further enriched with glycerol in the water phase. Liposomes and glycerosomes were prepared as well and used as reference. Vesicles were oligolamellar and multicompartment, as confirmed by cryogenic transmission electron microscopy (cryo-TEM) observation, small in size (~140 nm) and negatively charged (~-23 mV). Spray characteristics were evaluated by using the Spraytec® and instant images, from which the plume angle was measured. The range of the droplet size distribution and the narrow spray angle obtained suggest a good nebulization and a possible local deposition in the nasal cavity. In vitro studies performed by using human keratinocytes confirmed the high biocompatibility of vesicles and their ability to effectively counteract oxidative damage on cells induced by hydrogen peroxide. The overall collected data suggest that our vesicles are suitable as nasal spray.

Evaluation of the stability of a spray-dried tuberculosis vaccine candidate designed for dry powder respiratory delivery

Particle engineering via spray drying was used to develop a dry powder presentation of an adjuvanted tuberculosis vaccine candidate. This presentation utilizing a trileucine-trehalose excipient system was designed to be both thermostable and suitable for respiratory delivery. The stability of the spray-dried vaccine powder was assessed over one year at various storage temperatures (-20, 5, 25, 40, 50 °C) in terms of powder stability, adjuvant stability, and antigen stability. A formulation without trileucine was included as a control. The results showed that the interior particle structure and exterior particle morphology of the powder was maintained for one year at 40 °C, while the control case exhibited a small extent of particle fusing under the same storage conditions. Moisture content was maintained, and powder solid state remained amorphous for all storage temperatures. Aerosol performance was assessed with a commercial dry powder inhaler in combination with a human mouth-throat model. The emitted dose and lung dose were maintained for all samples after one year at temperatures up to 40 °C. Nanoemulsion size and oil content of the adjuvant system were maintained after one year at temperatures up to 40 °C, and the agonist content was maintained after one year at temperatures up to 25 °C. The antigen was completely degraded in the control formulation at seven months of storage at 40 °C; by contrast, 45% of the antigen was still present in the trehalose-trileucine formulation after one year of storage at 50 °C. Comparatively, the antigen was completely degraded in a liquid sample of the vaccine candidate after only one month of storage at 37 °C. The spray-dried trehalose-trileucine vaccine powder clearly maintained its inhalable properties after one year's storage at high temperatures and improved overall thermostability of the vaccine.

Inhalable Porous Microspheres Loaded with Metformin and Docosahexaenoic Acid Suppress Tumor Metastasis by Modulating Premetastatic Niche

Cancer metastasis is the major cause of cancer-related death; therefore, achieving suppression of tumor metastasis is a long-sought goal in cancer therapy. As the premetastatic niche acts as a prerequisite for tumor metastasis, it serves as an effective target for metastasis suppression. This study tests the feasibility of inhalable porous microspheres loaded with two premetastatic niche modulation agents, metformin and docosahexaenoic acid, as orthotopic delivery carriers for the reversion of lung premetastatic microenvironments and targeted suppression of tumor lung metastasis. The microspheres were prepared via an improved emulsion-solvent evaporation method and exhibit an excellent lung deposition, leading to significant inhibition of circulating tumor cells (CTCs)-endothelial cells adhesion, reduction of vascular permeability, and suppression of adhesion protein expression in lung premetastatic microenvironments. As a result, inhalable microspheres can prevent tumor lung metastasis formation excellently in vivo. Overall, this study proved that the encapsulation of metformin and docosahexaenoic acid in inhalable microspheres could be a promising strategy for tumor lung metastasis inhibition via orthotopically modulating premetastatic niche in the lungs.

Discovery of Small Anti-ACE2 Peptides to Inhibit SARS-CoV-2 Infectivity

COVID-19 is caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), which infects host cells by binding its viral spike protein receptor-binding domain (RBD) to the angiotensin converting enzyme 2 (ACE2) on host cells. Blocking the SARS-CoV-2-RBD/ACE2 interaction is, therefore, a potential strategy to inhibit viral infections. Using a novel biopanning strategy, a small anti-ACE2 peptide is discovered, which shows high affinity and specificity to human ACE2. It blocks not only the SARS-CoV-2-RBD/ACE2 interaction but also the SARS-CoV-1-RBD/ACE2 interaction. Moreover, it inhibits SARS-CoV-2 infection in Vero-E6 cells. The peptide shows negligible cytotoxicity in Vero-E6 cells and Huh7 cells. In vivo short-term lung toxicity study also demonstrates a good safety of the peptide after intratracheal administration. The anti-ACE2 peptide can be potentially used as a prophylactic or therapeutic agent for SARS-CoV-2 or other ACE2-mediated viruses. The strategy used in this study also provides a fast-track platform to discover other antiviral peptides, which will prepare the world for future pandemics.

Prevalence and Associated Factors of Suboptimal Daily Peak Inspiratory Flow and Technique Misuse of Dry Powder Inhalers in Outpatients with Stable Chronic Airway Diseases

Purpose

The present study aimed to investigate the prevalence and associated factors of suboptimal daily peak inspiratory flow (PIF) and technical misuse of three commonly used dry powder inhalers (DPIs) in outpatients with stable chronic airway diseases.

Patients and Methods

Included in this study were 85 outpatients with stable asthma, chronic obstructive pulmonary disease (COPD), or asthma-COPD Overlap (ACO) and had previously used any of Turbuhaler^® (TUR), Diskus^® (DIS), HandiHaler^® (HAN) between December 2018 and September 2019. The patient’s daily PIF against the resistance of a specific DPI and operation technique was investigated by two pharmacists by using In-Check DIAL G16 and a checklist.

Results

Of the 85 patients, the proportion of patients with a suboptimal daily PIF and technical misuse was 38.8% and 65.9%, respectively. In logistic regression, we observed that the factors that increase the risk for suboptimal daily PIF were age (OR=1.06) and combination with respiratory diseases (OR = 6.59). The factor that decreases the risk for misuse was the higher education level (OR =0.63).

Conclusion

Even if patients have received training at the time of initial prescription, the standardization of the use of DPIs by patients in our center was still unoptimistic. Age and combined with respiratory diseases were associated with suboptimal PIF. Higher education level decreased the incidence of technique misuse.

Cylindrical Microparticles Composed of Mesoporous Silica Nanoparticles for the Targeted Delivery of a Small Molecule and a Macromolecular Drug to the Lungs: Exemplified with Curcumin and siRNA

The transport of macromolecular drugs such as oligonucleotides into the lungs has become increasingly relevant in recent years due to their high potency. However, the chemical structure of this group of drugs poses a hurdle to their delivery, caused by the negative charge, membrane impermeability and instability. For example, siRNA to reduce tumour necrosis factor alpha (TNF-α) secretion to reduce inflammatory signals has been successfully delivered by inhalation. In order to increase the effect of the treatment, a co-transport of another anti-inflammatory ingredient was applied. Combining curcumin-loaded mesoporous silica nanoparticles in nanostructured cylindrical microparticles stabilized by the layer-by-layer technique using polyanionic siRNA against TNF-α was used for demonstration. This system showed aerodynamic properties suited for lung deposition (mass median aerodynamic diameter of 2.85 ± 0.44 µm). Furthermore, these inhalable carriers showed no acute in vitro toxicity tested in both alveolar epithelial cells and macrophages up to 48 h incubation. Ultimately, TNF-α release was significantly reduced by the particles, showing an improved activity co-delivering both drugs using such a drug-delivery system for specific inhibition of TNF-α in the lungs.

Augmentation therapy with alpha 1-antitrypsin: present and future of production, formulation, and delivery

Alpha 1-antitrypsin is one of the first protein therapeutics introduced on the market - more than 30 years ago - and, to date, it is indicated only for the treatment of the severe forms of a genetic condition known as alpha-1 antitrypsin deficiency. The only approved preparations are derived from plasma, posing potential problems associated with its limited supply and high processing costs. Moreover, augmentation therapy with alpha 1-antitrypsin is still limited to intravenous infusions, a cumbersome regimen for patients. Here, we review the recent literature on its possible future developments, focusing on i) the recombinant alternatives to the plasma-derived protein, ii) novel formulations, and iii) novel administration routes. Regulatory issues and the still unclear noncanonical functions of alpha 1-antitrypsin - possibly associated with the glycosylation pattern found only in the plasma-derived protein - have hindered the introduction of new products. However, potentially new therapeutic indications other than the treatment of alpha-1 antitrypsin deficiency might open the way to new sources and new formulations.

A Pathway From Porous Particle Technology Toward Tailoring Aerogels for Pulmonary Drug Administration

Pulmonary drug delivery has recognized benefits for both local and systemic treatments. Dry powder inhalers (DPIs) are convenient, portable and environmentally friendly devices, becoming an optimal choice for patients. The tailoring of novel formulations for DPIs, namely in the form of porous particles, is stimulating in the pharmaceutical research area to improve delivery efficiency. Suitable powder technological approaches are being sought to design such formulations. Namely, aerogel powders are nanostructured porous particles with particularly attractive properties (large surface area, excellent aerodynamic properties and high fluid uptake capacity) for these purposes. In this review, the most recent development on powder technologies used for the processing of particulate porous carriers are described via updated examples and critically discussed. A special focus will be devoted to the most recent advances and uses of aerogel technology to obtain porous particles with advanced performance in pulmonary delivery.

Novel formulations and drug delivery systems to administer biological solids

Recent advances in formulation sciences have expanded the previously limited design space for biological modalities, including peptide, protein, and vaccine products. At the same time, the discovery and application of new modalities, such as cellular therapies and gene therapies, have presented formidable challenges to formulation scientists. We explore these challenges and highlight the opportunities to overcome them through the development of novel formulations and drug delivery systems as biological solids. We review the current progress in both industry and academic laboratories, and we provide expert perspectives in those settings. Formulation scientists have made a tremendous effort to accommodate the needs of these novel delivery routes. These include stability-preserving formulations and dehydration processes as well as dosing regimes and dosage forms that improve patient compliance.

In-Depth Comparison of Dry Particle Coating Processes Used in DPI Particle Engineering

High-shear mixer coatings as well as mechanofusion processes are used in the particle-engineering of dry powder inhalation carrier systems. The aim of coating the carrier particle is usually to decrease carrier–drug adhesion. This study comprises the in-depth comparison of two established dry particle coating options. Both processes were conducted with and without a model additive (magnesium stearate). In doing so, changes in the behaviour of the processed particles can be traced back to either the process or the additive. It can be stated that the coarse model carrier showed no significant changes when processed without additives. By coating the particles with magnesium stearate, the surface energy decreased significantly. This leads to a significant enhancement of the aerodynamic performance of the respective carrier-based blends. Comparing the engineered carriers with each other, the high-shear mixer coating shows significant benefits, namely, lower drug–carrier adhesion and the higher efficiency of the coating process.

Leucine as an excipient in spray dried powder for inhalation

Leucine is a promising excipient with several applications in the development of inhalable spray-dried powder of high- and low-dose drugs. The addition of leucine has exhibited significant enhancing effects on the aerosolization and physical stability of the produced particles. Here, we focus not only on the applications of leucine in inhalable spray-drying powders, but also on the underlying mechanisms by which the formulation and processing parameters dictate the behavior of leucine during the drying process and, therefore, its functionalities within the dried powder. Additionally, we highlight the current regulatory status of leucine. Such insights are important for more efficient utilization of leucine in the future, both for dry powder inhaler formulations and other pharmaceutical applications.