Development of a compact computed tomographic apparatus for dental use

A preliminary study to determine the diagnostic reference level using dose-area product for limited-area cone beam CT

OBJECTIVES

The aim of this study was to measure the dose-area product (DAP) of limited-area cone beam CT (CBCT) units used by dental offices, and to evaluate the rationale of the DAP with an aid of optically stimulated luminescence (OSL) dosemeter in measuring radiation dose.

METHOD

The DAPs of 21 CBCT units used in the dental offices of Tokyo and the surrounding areas from five different manufacturers were measured using OSL nanoDot dosemeter. An assembly of OSL dosemeters with an X-ray film was exposed by CBCT units at exposure parameters commonly used in each dental office. DAP values were then calculated as expressed in mGy cm(2).

RESULTS

DAP values ranged from 126.7 mGy cm(2) to 1476.9 mGy cm(2), depending on the units used.

CONCLUSION

OSL dosemeter coupled with film can be utilized for a large-scale study to measure DAP. The DAP values for individual CBCT units depend not only on the field of view, but also on the exposure parameters adapted by the dental offices.

Performance of a photostimulable storage phosphor digital system with or without the sharpen filter and cone beam CT for detecting approximal enamel subsurface demineralization

OBJECTIVES

The aim of this study was to assess the performance of photostimulable storage phosphor (PSP) radiographs with or without using the sharpen filter and cone beam CT (CBCT) for detecting enamel subsurface demineralization.

METHODS

Enamel subsurface demineralization was induced on one of the approximal surfaces of 120 sound human teeth. Standardized images of all teeth were acquired after the demineralization phase using the Digora(®) Optime (Orion Corp./Soredex, Helsinki, Finland) (PSP) and the i-CAT™ (Imaging Sciences International, Hatfield, PA) (CBCT) systems. Three calibrated observers interpreted the images using a five-point scale (1, demineralization definitely absent; 2, demineralization probably absent; 3, unsure; 4, demineralization probably present; and 5, demineralization definitely present). Diagnoses were validated by cross-sectional microhardness profiling in the test areas of the approximal surfaces. Interobserver agreement was analysed using kappa statistics. Accuracy was estimated by the areas under the receiver operating characteristic curves (Az), which were compared using the Kruskal-Wallis test (α = 5%).

RESULTS

Interobserver agreement was higher for CBCT (κ = 0.7-0.8), followed by sharpen-filtered (κ = 0.6-0.7) and original (κ = 0.5-0.6) images. CBCT presented the highest accuracy value (Az = 0.897) compared with the original (Az = 0.792) and sharpen-filtered (Az = 0.712) images. However, no statistical differences were observed between the imaging modalities (p = 0.0794).

CONCLUSIONS

It can be concluded that PSP radiographs with or without using the sharpen filter and the CBCT images may be useful adjuncts for detecting subtle approximal enamel demineralization.

CBVT analysis of canal configuration of the mesio-buccal root of maxillary first permanent molar teeth: An in vitro study

CONTEXT

For successful endodontic treatment, it's imperative to locate and obturate all root canals. As concluded by Ingle, the major cause for failure of root canal therapy is in ability to recognize all theexisting canals and subsequent failure in their obturation.

AIM

To analyze the canal configuration of the mesio-buccal root of maxillary first permanent molar teeth.

MATERIALS AND METHODS

A total of 30 recently extracted human permanent maxillary first molars were collected and stored in a container with 5% Sodium Chloride solution for four days. Teeth with open apices, external resorption, improperly formed roots and teeth with previous restorations were excluded. Using the dental modeling wax, teeth were arranged in a 'U' shaped arch with roots embedded inside the wax and occlusal surface remaining free. 10 teeth were arranged in each arch and three such sample plates were prepared. Flat surface of the base encasing enabled the plate to be mounted on flat plastic bite plate. With bite plate roughly centered in the focal trough area Axial, Coronal and Sagittal section Cone-Beam Computed Tomography (CBCT) images were taken with Kodak 9000 Extra-oral Imaging System. Images displayed on a monitor were inspected by two endodontists using Kodak Dental Imaging Software 3D Module V2.2.

STATISTICAL ANALYSIS

When the data was observed, it was found that 24 teeth out of total 30 teeth examined showed some variation (i.e. possible additional canal) along the length of the mesio-buccal root canal. Out of these 24 teeth, 13 showed presence of additional canal at coronal third, 7 showed presence of additional canal at middle third and four showed presence of additional canal in apical third level. Percentage analysis was done as there was no group comparison to be done.

RESULTS

Cone-Beam Volumetric Tomography (CBVT) evaluation positively identified the variations in mesio-buccal canal in 80% of samples. Out of these, 54.16% were in coronal 3(rd), 29.16% in middle 3(rd) and 16.66% were in apical 3(rd).

CONCLUSION

Within the limitations of this study, it can be concluded that- (1) more than half of maxillary first molars have four canals and (2) most of the additional canals were located in the MBR and CBVT is a good diagnostic tool to help diagnose these additional canals. Further investigations using larger sample sizes would be helpful.

Three-dimensional images contribute to the diagnosis of mucous retention cyst in maxillary sinus

OBJECTIVE

To evaluate the detection of mucous retention cyst of maxillary sinus (MRCMS) using panoramic radiography and cone beam computed tomography (CBCT).

STUDY DESIGN

A digital database with 6,000 panoramic radiographs was reviewed for MRCMS. Suggestive images of MRCMS were detected on 185 radiographs, and patients were located and invited to return for follow-up. Thirty patients returned, and control panoramic radiographs were obtained 6 to 46 months after the initial radiograph. When MRCMS was found on control radiographs, CBCT scans were obtained. Cysts were measured and compared on radiographs and scans. The Wilcoxon, Spearman and Kolmorogov-Smirnov tests were used for statistical analysis. The level of significance was set at 5%.

RESULTS

There were statistically significant differences between the two methods (p<0.05): 23 MRCMS detected on panoramic radiographs were confirmed by CBCT, but 5 MRCMS detected on CBCT images had not been identified by panoramic radiography. Eight MRCMS detected on control radiographs were not confirmed by CBCT. MRCMS size differences from initial to control panoramic radiographs and CBCT scans were not statistically significant (p= 0.617 and p= 0.626). The correlation between time and MRCMS size differences was not significant (r = -0.16, p = 0.381).

CONCLUSION

CBCT scanning detect MRCMS more accurately than panoramic radiography.

Effect of root canal filling materials on dimensions of cone-beam computed tomography images

Objective

To evaluate the discrepancy of root canal filling (RCF) measurements obtained from original root specimens and cone-beam computed tomography (CBCT) images.

Material and Methods

Seventy-two human maxillary anterior teeth were prepared up to an ISO #50 K-File 1 mm short of the apical foramen. Thus, the teeth were randomly divided into 8 groups, according to the root canal filling material: Sealapex^®, Sealapex^®+gutta-percha points, Sealer 26^®, Sealer 26^®+gutta-percha points, AH PlusTM, AH PlusTM+gutta-percha points, Grossman Sealer, and Grossman Sealer+gutta-percha points. After root canal preparation and RCF, CBCT scans were acquired and the specimens were sectioned in axial, sagittal and coronal planes. The RCF measurements were obtained in different planes and thicknesses to determine the discrepancy between the original root specimens (using a digital caliper) and the CBCT images (using the scanner's proprietary software). One-way analysis of variance and Tukey tests were used for statistical analyses. The significance level was set at α=5%.

Results

Measurements of the different endodontic filling materials were 9% to 100% greater on the CBCT images than on the original root specimens. Greater RCF dimensions were found when only sealers were used, with statistically significant difference among the groups.

Conclusions

RCF dimensions were greater on CBCT images than on the original root specimens, especially when only sealer was used.

Effect of exposure time on the accuracy and reliability of cone beam computed tomography in the assessment of dental implant site dimensions in dry skulls

OBJECTIVES

To investigate the accuracy and reliability of implant site measurements, recorded from low-dose cone beam computed tomography (CBCT) images.

METHODS

CBCT reformatted images of five skulls were obtained using 40, 20 and 7 s exposure protocols. From these protocols, edentulous ridge dimensions were recorded by two observers and compared with measurements recorded directly from the bone. The measurement errors and intra- and inter-examiner reliability were calculated for each exposure protocol and compared with each other.

RESULTS

The mean absolute errors from the 40, 20 and 7 s protocols were 0.50, 0.46, and 0.51 mm, respectively. The intra-examiner reliability scores were 0.996, 0.995 and 0.998, respectively. The inter-examiner reliability scores were 0.993, 0.998 and 0.994, respectively. There was no significant difference in accuracy or reliability between the three protocols.

CONCLUSIONS

In imaging of dry skulls, lowering the CBCT exposure time from 40 s to 20 or 7 s does not affect the reliability or accuracy of implant site measurements.

Measurement and comparison of labyrinthine structures with the digital volume tomography: ancient Egyptian mummies' versus today's temporal bones

The objective of this study was to investigate whether the labyrinthine structures of ancient Egyptian mummies differ significantly from modern labyrinths. The new technique of digital volume tomography (DVT) was used to visualize the temporal bones. To obtain standardized images and measurements, precise instructions regarding volume rotation, slicing and measurements' positioning were determined. Twenty-five dimensions were obtained. The groups were compared statistically. No significant differences could be found except one cochlear diameter which proved to be significantly larger in the control group. DVT is applicable for imaging of temporal bones. Measurements might help to increase understanding of the temporal bone's structure, to aid the diagnostics of pathologies as well as to supplement the planning of surgical procedures.

Accuracy of linear intraoral measurements using cone beam CT and multidetector CT: a tale of two CTs

OBJECTIVES

The aim was to compare the accuracy of linear bone measurements of cone beam CT (CBCT) with multidetector CT (MDCT) and validate intraoral soft-tissue measurements in CBCT.

METHODS

Comparable views of CBCT and MDCT were obtained from eight intact cadaveric heads. The anatomical positions of the gingival margin and the buccal alveolar bone ridge were determined. Image measurements (CBCT/MDCT) were performed upon multiplanar reformatted data sets and compared with the anatomical measurements; the number of non-assessable sites (NASs) was evaluated.

RESULTS

Radiological measurements were accurate with a mean difference from anatomical measurements of 0.14 mm (CBCT) and 0.23 mm (MDCT). These differences were statistically not significant, but the limits of agreement for bone measurements were broader in MDCT (-1.35 mm; 1.82 mm) than in CBCT (-0.93 mm; 1.21 mm). The limits of agreement for soft-tissue measurements in CBCT were smaller (-0.77 mm; 1.07 mm), indicating a slightly higher accuracy. More NASs occurred in MDCT (14.5%) than in CBCT (8.3%).

CONCLUSIONS

CBCT is slightly more reliable for linear measurements than MDCT and less affected by metal artefacts. CBCT accuracy of linear intraoral soft-tissue measurements is similar to the accuracy of bone measurements.

Imaging of ancient Egyptian mummies' temporal bones with digital volume tomography

The radiographic imaging of ancient Egyptian mummies has always been of great interest. Computed tomography is the method of choice to demonstrate bony pathologies with high quality. As digital volume tomography (DVT) is an extension of panoramic tomography with a very high resolution, its qualities were evaluated by examination of temporal bones of Egyptian mummy skulls. Ten Egyptian mummy skulls from the Zoological Collection Marburg, estimated 1,700-5,000 years of age, from Abydos, Philae, Theben-West and Sakkarah, were examined by DVT (3D Accuitomo, Morita, Japan). Through a rotation 360° of the X-ray source around the region of interest, a cylinder of 3 × 4 cm was captured as a three-dimensional volume. The gained data were analyzed with the help of special software on a PC. The angles of the axial, coronal and sagittal sections were arbitrarily changed to represent single structures with high resolution of 0.125 mm to analyze specific anatomical structures. In all skulls, conditions of the temporal bone and its anatomical structures were evaluated and normal as well as pathological findings evaluated in detail. The analysis of special landmarks such as the ossicular chain, cochlea, external, and internal auditory canal, facial nerve canal, and semicircular canals showed an intact ossicular chain in six temporal bones, while only isolated and dislocated ossicles were found in eight temporal bones. Besides one dehiscence of the superior semicircular canal in one temporal bone which might have led to vertigo and deafness at lifetime, all other findings were normal. Fragments of foreign bodies additionally found in the labyrinth, external ear canal and intracranially were attributed to postmortem damage. Digital volume tomography extends the imaging possibilities of CT for paleoradiological evaluation of temporal bones. With its high resolution, geometric accuracy, reconstruction capabilities, rapidness, and comparably low costs, even small bony pathologies are precisely demonstrated in a limited area. Investigations of larger numbers of specimen might reveal further details of ancient history for further interdisciplinary investigation of anthropologists, Egyptiologists, otolaryngologists, and radiologists.

Detection of a secondary mesio-buccal canal in maxillary first molar: A comparative study

AIM

The purpose of this study was to clarify detection characteristics of the secondary mesio-buccal canal in maxillary first molars using various methods.

MATERIALS AND METHODS

The root canal system of 86 extracted human maxillary first molars was inspected using micro-focus-computed tomography to accurately determine the number of canals. Radiographs or floors of the pulp chamber for all samples were observed for the secondary mesio-buccal canal with computed tomography for dentistry, digital dental radiography, magnifier, or the naked eye. Sensitivity, specificity, positive, and negative predictive values and diagnostic accuracy for these four methods were investigated using the results from the micro-focus-computed tomography inspection as the gold standard. All samples of each method were observed by 10 endodontists. Using these results, the χ(2) test was used to compare and analyze differences between the various conditions (P<0.05).

RESULTS

The secondary mesio-buccal canal could be recognized in 60.9% of samples with the micro-focus-computed tomography. No significant difference was seen between efficiencies of the computed tomography for dentistry and the micro-focus-computed tomography. The computed tomography for dentistry was superior to the other three methods.

CONCLUSION

Detectability of the secondary mesio-buccal canal in the maxillary first molar was superior using dental-computed tomography compared to digital dental radiography, magnification telescope, and the naked eye.

Evaluation of a cone beam CT artefact reduction algorithm

OBJECTIVES

An algorithm and software to reduce metal artefact has been developed recently and is available in the Picasso Master 3D® (VATECH, Hwaseong, Republic of Korea), which under visual assessment produces better quality images than were obtainable previously. The objective of this in vitro study was to investigate whether the metal artefact reduction (MAR) algorithm of the Picasso Master 3D machine reduced the incidence of metal artefacts and increased the contrast-to-noise ratio (CNR) while maintaining the same gray value when there was no metallic body present within the scanned volume.

METHODS

20 scans with a range of 50-90 kVp were acquired, of which 10 had a metallic bead inserted within a phantom. The images obtained were analysed using public domain software (ImageJ; NIH Image, Bethesda, MD). Area histograms were used to evaluate the mean gray level variation of the epoxy resin-based substitute (ERBS) block and a control area. The CNR was calculated.

RESULTS

The MAR algorithm increased the CNR when the metallic bead was present; it enhanced the ERBS gray level independently of the presence of the metallic bead. The image quality also improved as peak tube potential was increased.

CONCLUSION

Improved quality of images and regaining of the control gray values of a phantom were achieved when the MAR algorithm was used in the presence of a metallic bead.

Metal artefact reduction with cone beam CT: an in vitro study

BACKGROUND

Metal in a patient's mouth has been shown to cause artefacts that can interfere with the diagnostic quality of cone beam CT. Recently, a manufacturer has made an algorithm and software available which reduces metal streak artefact (Picasso Master 3D® machine; Vatech, Hwaseong, Republic of Korea).

OBJECTIVES

The purpose of this investigation was to determine whether or not the metal artefact reduction algorithm was effective and enhanced the contrast-to-noise ratio.

METHODS

A phantom was constructed incorporating three metallic beads and three epoxy resin-based bone substitutes to simulate bone next to metal. The phantom was placed in the centre of the field of view and at the periphery. 10 data sets were acquired at 50-90 kVp. The images obtained were analysed using a public domain software ImageJ (NIH Image, Bethesda, MD). Profile lines were used to evaluate grey level changes and area histograms were used to evaluate contrast. The contrast-to-noise ratio was calculated.

RESULTS

The metal artefact reduction option reduced grey value variation and increased the contrast-to-noise ratio. The grey value varied least when the phantom was in the middle of the volume and the metal artefact reduction was activated. The image quality improved as the peak kilovoltage increased.

CONCLUSION

Better images of a phantom were obtained when the metal artefact reduction algorithm was used.

Accuracy assessment of the axial images obtained from cone beam computed tomography

OBJECTIVE

The aim of this study was to evaluate accuracy of linear measurements assessed from axial tomograms and the influence of the use of different protocols in two cone beam CT (CBCT) units.

METHODS

A cylinder object consisting of Nylon® (Day Brazil, Sao Paulo, Brazil) with radiopaque markers was radiographically examined applying different protocols from NewTom 3G(TM) (Quantitative Radiology s.r.l, Verona, Veneto, Italy) and i-CAT(TM) (Imaging Sciences International, Hatfield, PA) units. Horizontal (A-B) and vertical (C-D) distances were assessed from axial tomograms and measured using a digital calliper that provided the gold standard for actual values.

RESULTS

There were differences when considering acquisition protocols to each CBCT unit. Concerning all analysed protocols from i-CAT(TM) and Newtom 3G(TM), both A-B and C-D distances presented underestimated values. Measurements of the axial images obtained from NewTom 3G(TM) (6 inch 0.16 mm and 9 inch 0.25 mm) were similar to the ones obtained from i-CAT(TM) (13 cm 20 s 0.3 mm, 13 cm 20 s 0.4 mm and 13 cm 40 s 0.25 mm).

CONCLUSION

The use of different protocols from CBCT machines influences linear measurements assessed from axial images. Linear distances were underestimated in both equipments. Our findings suggest that the best protocol for the i-CAT(TM) is 13 cm 20 s 0.3 mm and for the NewTom 3G(TM), the use of 6 inch or 9 inch is recommended.

The usage of digital radiography and cone beam computed tomography among Turkish dentists

OBJECTIVES

The aim of this study was to determine the prevalence of the use of digital radiography and report how it was used by Turkish dentists.

METHODS

The survey was based on 383 dentists who were present at the sixteenth International Congress organized by the Turkish Dental Association. A questionnaire which consisted of 19 questions was given to the dentists who participated in the study. Data were assessed according to frequency distribution and the χ(2) test was used to determine the significance of differences between two independent groups.

RESULTS

376 questionnaires were analysed. The mean age of the dentists who participated in the study was 37.14 ± 9.6 years (range: 20-63 years). The distribution of the dentists according to the 7 regions of Turkey were: Marmara 58%, Aegean 13% and Mediterranean 10%, Central Anatolia 8%, Black Sea 7%, Southeastern Anatolia 3%, Eastern Anatolia 1%. 124 dentists (33%) said they did not work with digital radiography. 95 dentists indicated that they did not use digital radiography owing to cost (60%). 252 dentists (67%) said they used digital radiography. 40% of the participants noted that the repetition of periapical radiographs was due to digital radiography. 166 dentists (55.9%) and 79.1% academicians had knowledge about cone beam CT (CBCT).

CONCLUSION

Digital radiography users are increasing in Turkey and levels of knowledge of CBCT and awareness of radiation safety has also increased.

Correlation of cone beam computed tomography (CBCT) findings in the maxillary sinus with dental diagnoses: a retrospective cross-sectional study

This study was conducted to assess the coincidence of mucosal hyperplasia in the maxillary sinus and related clinical diagnoses of posterior maxillary teeth found in cone beam computed tomography (CBCT) scans. A total of 204 patients who underwent CBCT examinations between 2006 and 2008 were evaluated retrospectively. Clinical and CBCT findings were correlated using patient records. Absolute frequencies, odds ratios (OR), and 95% confidence intervals (95% CI) were calculated for statistical evaluations. There was a pronounced association between periodontitis and radiological signs of sinusitis. Basal mucosal wall thickening was more likely in patients with decayed and non-vital teeth compared to patients with sound teeth (OR = 5.2; 95% CI = 1.2-23.1). Basal mucosal wall thickening was also more likely than total mucosal thickening (OR = 10.4; 95% CI = 2.6-42.2). Patients with decayed and endodontically treated teeth were more likely to exhibit involvement of the basal wall (OR = 9.2; 95% CI = 3.3-25.2) than were patients with healthy teeth. CBCT examinations revealed a correlation between basal mucosal thickening in the maxillary sinus and decayed posterior maxillary teeth or periodontitis. Chronic symptoms involving the sinuses are one of the most common reasons for patients to consult physicians. One reason for chronic orofacial pain is the prevalence of undiagnosed sinus conditions.

Use of cone beam computed tomography in otolaryngologic treatments

Cone beam computed tomography (CBCT) allows us to evaluate 3-dimensional (3D) morphology of the maxillofacial skeleton and also used in dentomaxillofacial imaging to solve complex diagnostic and treatment planning problems such as craniofacial fractures, temporamandibular dysfunctions or sinus imaging. CBCT uses a rectangular or round 2D detector, which allows a single rotation of the gantry to generate a scan of the entire region of interest. Technological and application-specific factors such as development of compact, relatively low-cost, high-quality, large, flat-panel detector arrays; the availability of low-cost computers with processing power sufficient for cone beam image reconstruction; the fabrication of highly efficient radiograph tubes capable of multiple exposures necessary for cone beam scanning at prices lower than those currently used for fan beam CT; and limited volume scanning (e.g., head and neck) eliminating the need for subsecond gantry rotation speeds make this possible. The objective of this study is to review published evidence for CBCT having an important role in ORL treatments. We aimed to review all the available literature about the CBCT imagination in ORL treatments. Systematic literature search was performed using PubMed and Ovid. Additional literature was retrieved from reference lists in the articles. Systematic analysis of the literature from 1998 to 2010 was performed. A total of 40 abstracts were evaluated independently by two members of the project group, and 38 articles were included in the review.

Accuracy of linear measurement in the Galileos cone beam computed tomography under simulated clinical conditions

OBJECTIVES

The aim of this study was to determine the geometric accuracy of cone beam CT (CBCT)-based linear measurements of bone height obtained with the Galileos CBCT (Sirona Dental Systems Inc., Bensheim, Hessen, Germany) in the presence of soft tissues.

METHODS

Six embalmed cadaver heads were imaged with the Galileos CBCT unit subsequent to placement of radiopaque fiduciary markers over the buccal and lingual cortical plates. Electronic linear measurements of bone height were obtained using the Sirona software. Physical measurements were obtained with digital calipers at the same location. This distance was compared on all six specimens bilaterally to determine accuracy of the image measurements.

RESULTS

The findings showed no statistically significant difference between the imaging and physical measurements (P > 0.05) as determined by a paired sample t-test. The intraclass correlation was used to measure the intrarater reliability of repeated measures and there was no statistically significant difference between measurements performed at the same location (P > 0.05).

CONCLUSIONS

The Galileos CBCT image-based linear measurement between anatomical structures within the mandible in the presence of soft tissues is sufficiently accurate for clinical use.

A comparative study of the accuracy and reliability of multidetector computed tomography and cone beam computed tomography in the assessment of dental implant site dimensions

OBJECTIVES

The aim of this study was to investigate the accuracy and reliability of linear measurements of edentulous ridges recorded from 16-row multidetector CT (MDCT) images and cone beam CT (CBCT) images acquired using a flat panel detector (FPD) with a large field of view (FOV), both independently and in comparison with each other.

METHODS

Edentulous areas of human dry skulls were marked with gutta-percha markers to standardize the plane of the transverse cross-sections and path of measurements. The skulls were imaged using a 16-row MDCT scanner and a CBCT device with a large FOV and a FPD. Ridge dimensions were recorded from reformatted sections by two observers and compared with measurements recorded directly from the bone. The measurement errors and intra and interexaminer reliability were calculated for each modality and compared with each other.

RESULTS

The overall mean of the absolute errors was 0.75 mm for MDCT and 0.49 mm for CBCT. The mean of the CBCT absolute errors was smaller than that of the MDCT absolute errors for the overall data, as well as for the site-specific data. The intraexaminer reliability score was 0.994 for MDCT and 0.995 for CBCT. The interexaminer reliability was 0.985 for MDCT and 0.958 for CBCT.

CONCLUSIONS

Both MDCT and CBCT were associated with a clinically and statistically significant measurement error. CBCT measurements were significantly more accurate than those of MDCT. The measurements recorded from both modalities had a high inter and intraexaminer reliability. Accuracy of measurements was found to be more operator dependent with CBCT than with MDCT.

Three-dimensional surgical simulation

In this article, we discuss the development of methods for computer-aided jaw surgery, which allows us to incorporate the high level of precision necessary for transferring virtual plans into the operating room. We also present a complete computer-aided surgery system developed in close collaboration with surgeons. Surgery planning and simulation include construction of 3-dimensional surface models from cone-beam computed tomography, dynamic cephalometry, semiautomatic mirroring, interactive cutting of bone, and bony segment repositioning. A virtual setup can be used to manufacture positioning splints for intraoperative guidance. The system provides further intraoperative assistance with a computer display showing jaw positions and 3-dimensional positioning guides updated in real time during the surgical procedure. The computer-aided surgery system aids in dealing with complex cases with benefits for the patient, with surgical practice, and for orthodontic finishing. Advanced software tools for diagnosis and treatment planning allow preparation of detailed operative plans, osteotomy repositioning, bone reconstructions, surgical resident training, and assessing the difficulties of the surgical procedures before the surgery. Computer-aided surgery can make the elaboration of the surgical plan a more flexible process, increase the level of detail and accuracy of the plan, yield higher operative precision and control, and enhance documentation of cases.

Diagnostic performance of magnetic resonance imaging for detecting osseous abnormalities of the temporomandibular joint and its correlation with cone beam computed tomography

OBJECTIVE

With cone beam CT (CBCT) as the reference standard, the objective of this study was to determine the diagnostic accuracy of MRI for assessing osseous abnormalities of the temporomandibular joint (TMJ).

METHODS

106 TMJs from 55 patients with temporomandibular disorder were examined by CBCT and MRI. CBCT images were evaluated by two experienced oral radiologists with regard to the presence or absence of each of the following eight types of osseous abnormalities: Type 1, destructive and erosive osseous changes of the condyle; Type 2, flattening of the articular surface of the condyle; Type 3, deformity of the condyle; Type 4, sclerosis of the condyle; Type 5, osteophyte formation; Type 6, ankylosis; Type 7, erosion of the articular fossa and/or eminence; and Type 8, sclerosis of the articular fossa and/or eminence. For detection of these osseous abnormalities by MRI, proton density-weighted images and T(2) weighted images were evaluated independently by three observers. Using CBCT findings as the reference standard, the diagnostic performance of MRI for detecting various types of osseous abnormalities was evaluated by calculating its sensitivity and specificity.

RESULTS

Out of 106 joints, CBCT revealed Types 1, 2, 3, 4, 5, 6, 7 and 8 abnormalities in 25, 19, 26, 20, 14, 5, 19 and 22 joints, respectively. The mean sensitivities of MRI among the three observers for detecting Types 1, 2, 3, 4, 5, 6, 7 and 8 abnormalities were 61%, 30%, 82%, 40%, 48%, 34%, 61% and 41%, respectively, whereas the mean specificities were 86%, 92%, 91%, 95%, 84%, 98%, 89% and 91%, respectively.

CONCLUSIONS

Although high specificity (84-98%) was obtained with MRI, this modality showed relatively low sensitivity (30-82%) for detecting osseous abnormalities of the TMJ. The value of MRI for the detection of TMJ osseous abnormalities is considered to be limited.

Identification of the mandibular vital structures: practical clinical applications of anatomy and radiological examination methods

Objectives

The purpose of this article was to review the current available clinical techniques and to recommend the most appropriate imaging modalities for the identification of mandibular vital structures when planning for oral implants.

Material and Methods

The literature was selected through a search of PubMed, Embase and Cochrane electronic databases. The keywords used for search were mandibular canal, mandibular incisive canal, mental foramen, anterior loop of the mental nerve, radiography, dental implants. The search was restricted to English language articles, published from January 1976 to January 2010.

Results

In total 111 literature sources were obtained and reviewed. The peculiarities of the clinical anatomy of mandibular canal, mandibular incisive canal, mental foramen and anterior loop of mental nerve were discussed. Radiological diagnostic methods currently available for the identification of the mandibular vital structures when planning for oral implants were presented. Guidelines for the identification of the mandibular vital structures in dental implantology were made.

Conclusions

The proposed guideline provides clinicians a tool in proper identifying the important mandibular vital structures thus minimizing the potential complications during implant surgery.

Modern dental imaging: a review of the current technology and clinical applications in dental practice

A review of modern imaging techniques commonly used in dental practice and their clinical applications is presented. The current dental examinations consist of intraoral imaging with digital indirect and direct receptors, while extraoral imaging is divided into traditional tomographic/panoramic imaging and the more recently introduced cone beam computed tomography. Applications, limitations and current trends of these dental "in-office" radiographic techniques are discussed.

Bifid mandibular canals: cone beam computed tomography evaluation

OBJECTIVES

For surgical procedures involving the posterior mandible, it is important to be familiar with the details of the bifid mandibular canal. To our knowledge, there have been no systematic studies evaluating the bifid mandibular canal using sectional imaging. The purpose of this study is to evaluate the incidence and configuration of the bifid mandibular canal using cone beam CT.

METHODS

252 patients (301 mandible sides) underwent cone beam CT between October 2004 and September 2005 and were included in this study. The cone beam CT images were evaluated for the presence and configuration of the bifid mandibular canal. The patterns of bifurcation were classified into four types according to the classification of Nortjé et al (Variations in the normal anatomy of the inferior dental (mandibular) canal: a retrospective study of panoramic radiographs from 3612 routine dental patients. Br J Oral Surg 1977; 15: 55-63). The diameter of the accessory canal was classified into two categories: 50% or more and less than 50% of the diameter of the main mandibular canal.

RESULTS

Of the 301 subjects, 47 (15.6%) demonstrated a bifid mandibular canal. They were Type I in 2, Type II in 40, Type III in 0, and Type IV in 5 cases. The diameter of the accessory canal was greater than or equal to 50% of the main canal in 23, and less than 50% in 24 cases.

CONCLUSIONS

On the basis of the cone beam CT, a bifid mandibular canal was found in 15.6% of cases, a markedly higher proportion than found in previous reports using panoramic images. Cone beam CT is considered a suitable modality for detailed evaluation of bifid mandibular canals.

Modulation transfer function evaluation of cone beam computed tomography for dental use with the oversampling method

OBJECTIVES

The aim was to investigate the possibility of evaluating the modulation transfer function (MTF) of cone beam CT (CBCT) for dental use using the oversampling method.

METHODS

The CBCT apparatus (3D Accuitomo) with an image intensifier was used with a 100 mum tungsten wire placed inside the scanner at a slight angle to the plane perpendicular to the plane of interest and scanned. 200 contiguous reconstructed images were used to obtain the oversampling line-spread function (LSF). The MTF curve was obtained by computing the Fourier transformation from the oversampled LSF. Line pair tests were also performed using Catphan(R).

RESULTS

The oversampling method provided smooth and reproducible MTF curves. The MTF curves revealed that the spatial resolution in the z-axis direction was significantly higher than that in the axial direction. This result was also confirmed by the line pair test.

CONCLUSIONS

MTF analysis was performed successfully using the oversampling method. In addition, this study clarified that the 3D Accuitomo had high spatial resolution, especially in the z-axis direction.

Case report: Cone-beam ct imaging in the management of a double tooth

BACKGROUND

The diagnosis and management strategies of double teeth have largely relied on clinical examination and conventional radiographic findings. Cone-Beam Computed Tomography (Cone-beam CT) was developed in the late 1990's and, therefore, is a relatively recent addition to the imaging armamentarium for use in Maxillofacial Radiology. There have been no publications in the dental literature demonstrating the use of Cone-beam CT or 3D stereolithography in the diagnosis and surgical planning of the management of double teeth.

CASE REPORT

An 11 year old girl presented with a double left lateral maxillary incisor. Conventional plain film radiography failed to provide the requisite information for pre-operative planning. Cone-beam Computed Tomography (Cone-beam CT) allowed determination of location of fusion, three-dimensional (3D) visualisation of pulpal anatomy and the construction of a 3D stereolithographic model for surgical planning. The double tooth was surgically divided in situ under local analgesia. The redundant distal unit was extracted and the residual mesial unit built up in composite resin following physiological mesial drift of displaced maxillary left canine. No endodontic therapy was required.

FOLLOW-UP

At a 10-month follow-up visit, clinical and radiographic vitality and success was noted.

CONCLUSION

The great amount of radiological information which Cone-beam CT can offer not only improves pre-operative and surgical planning, but the 3D models provided can be used to further educate and inform patients and guardians in the management of double teeth.

Diagnostic accuracy of microcomputed tomography for osseous abnormalities in the rat temporomandibular joint condyle

OBJECTIVES

Our aim was to investigate the diagnostic accuracy of in vivo micro-CT for osseous abnormalities of the rat temporomandibular joint (TMJ) condyle, using macroscopic observations as the "gold standard".

METHODS

A 30 TMJ arthritis model was prepared by injecting inflammatory complete Freund's adjuvant (CFA) into one side of the TMJ cavities of rats. The TMJ condyles were then imaged using micro-CT. The samples were macroscopically evaluated for osseous abnormalities, including erosions, osteophytes, flattening and concavity. The micro-CT images were independently assessed for abnormalities using the same criteria. Images in three planes were produced using the micro-XYZ technique with the micro-CT equipment.

RESULTS

According to the macroscopic observations, 26 of the 60 rat condyles showed osseous abnormalities. The micro-XYZ images detected abnormalities in 25 of the condyles. The condyle diagnostic accuracy of micro-CT was 0.98, the sensitivity was 0.96 and the specificity was 1.0.

CONCLUSIONS

Good diagnostic results were obtained using micro-CT. It is therefore an effective technique for the evaluation of osseous abnormalities in the rat TMJ condyle.

Accuracy and precision of linear measurements in cone beam computed tomography Accuitomo tomograms obtained with different reconstruction techniques

OBJECTIVES

To assess the accuracy and precision of linear measurements, the influence of different object positions in cone beam CT (CBCT) images and the effect of different systems for reformatting and viewing the tomograms on measurement values.

METHODS

An object consisting of Plexiglas plates with metal spheres was radiographically examined in three positions using the CBCT unit Accuitomo. Tomograms were reformatted using the i-Dixel software and Sectra picture archiving and communication system (PACS) multiplanar reformatting (MPR). Two observers measured 20 linear distances in axial, frontal and sagittal planes. Physical measurements of actual distances by means of a digital caliper served as the gold standard.

RESULTS

For measurements performed on the Accuitomo and Sectra PACS workstations, the mean differences between repeated measurements were below 0.13 mm (standard deviation (SD) 0.13 mm) and 0.21 mm (SD 0.18 mm), respectively. Mean differences between the two observers were below 0.11 mm (SD 0.07 mm) and 0.15 mm (SD 0.09 mm). The mean difference between the gold standard and the basic position when using the Accuitomo workstation, was -0.08 mm (SD 0.21 mm) and for a deviated/rotated position -0.08 mm (SD 0.23 mm) and -0.09 mm (SD 0.20 mm). None was statistically significant (P > 0.05). For measurement performed on MPR tomograms using the Sectra PACS workstation, mean differences were -0.09 mm (SD 0.17 mm) for basic position, and -0.08 mm (SD 0.19 mm) and -0.13 mm (SD 0.15 mm) for deviated and rotated positions, respectively. The mean difference between gold standard and basic/rotated positions was statistically significant, with P = 0.032 and P = 0.002.

CONCLUSIONS

Our study confirms previous findings indicating that measurements in 3DX Accuitomo FPD (flat panel detector) tomograms show a high level of agreement with actual distances. Our findings suggest the possibility of minor distortion in tomograms reformatted by means of Sectra PACS MPR.

Dosimetry and image quality of four dental cone beam computed tomography scanners compared with multislice computed tomography scanners

OBJECTIVES

The aim of this study was to evaluate the radiation dose and image quality of four dental cone beam CT (CBCT) scanners, and to compare them with those of two multislice CT (MSCT) scanners.

METHODS

Tissue doses were measured using a tissue-equivalent anthropomorphic RANDO Head Phantom((R)) with thermoluminescence dosemeters (TLD). An RSVP Head Phantom(TM) with a specially designed cylindrical insert was used for comparison of image quality and absorbed dose. Image quality was evaluated in the form of contrast-to-noise ratio (CNR) and modulation transfer function (MTF).

RESULTS

Using standard imaging parameters, the effective doses varied between 14 microSv and 269 microSv (International Commission on Radiation Protection (ICRP) 1990) and 27 microSv and 674 microSv (ICRP 2008) with the CBCT scanners, and between 350 microSv and 742 microSv (ICRP 1990) and 685 microSv and 1410 microSv (ICRP 2008) with the MSCT scanners. The CNR of the CBCT and MSCT scanners were 8.2-18.8 and 13.6-20.7, respectively. Low-dose MSCT protocols provided CNRs comparable with those from CBCT scanners. The 10% MTF of the CBCT scanners varied between 0.1 mm(-1) and 0.8 mm(-1), and was 0.5 mm(-1) for all the MSCT protocols examined.

CONCLUSIONS

CBCT scanners provide adequate image quality for dentomaxillofacial examinations while delivering considerably smaller effective doses to the patient. Large variations in patient dose and image quality emphasize the importance of optimizing imaging parameters in both CBCT and MSCT examinations.

Absorbed and effective doses from cone beam volumetric imaging for implant planning

OBJECTIVES

Volumetric CT using a cone beam has been developed by several manufacturers for dentomaxillofacial imaging. The purpose of this study was to measure doses for implant planning with cone beam volumetric imaging (CBVI) in comparison with conventional multidetector CT (MDCT).

METHODS

The two CBVI systems used were a 3D Accuitomo (J. Morita), including an image-intensifier type (II) and a flat-panel type (FPD), and a CB MercuRay (Hitachi). The 3D Accuitomo operated at 80 kV, 5 mA and 18 s. The CB MercuRay operated at 120 kV, 15 mA, 9.8 s. The MDCT used was a HiSpeed QX/i (GE), operated at 120 kV, 100 mA and 0.7 s, and its scan length was 77 mm for both jaws. Measurement of the absorbed tissue and organ doses was performed with an Alderson phantom, embedding the radiophotoluminescence glass dosemeter into the organs/tissues. The values obtained were converted into the absorbed dose. The effective dose as defined by the International Commission on Radiological Protection was then calculated.

RESULTS

The absorbed doses of the 3D Accuitomo of the organs in the primary beam ranged from 1-5 mGy, and were several to ten times lower than other doses. The effective dose of the 3D Accuitomo ranged from 18 muSv to 66 muSv, and was an order of magnitude smaller than the others. In conclusion, these results show that the dose in the 3D Accuitomo is lower than the CB MercuRay and much less than MDCT.

Evaluation of the severity of temporomandibular joint osteoarthritic changes related to age using cone beam computed tomography

OBJECTIVES

The aim of this study is to evaluate and correlate with age the severity of temporomandibular joint (TMJ) osteoarthritic changes using cone beam CT (CBCT).

METHODS

The images of 71 patients with findings of degenerative arthritis were retrieved from the computer data base. All patients had been examined with CBCT (NewTom 9000 QR-DVT). Left and right TMJs were evaluated independently for each patient. TMJ evaluation included: (a) bony changes of the condyle (flattening, erosion, sclerosis, osteophytes, resorption); (b) joint space (normal, increased, reduced, bony contact between the condyle and the mandibular fossa); and (c) bony changes of mandibular fossa (normal, sclerosis, erosion, resorption). The radiographic findings were statistically analysed.

RESULTS

Significant differences in the mean age were found: (a) between absent and moderate erosion (P = 0.019), as well as between absent and extensive erosion (P = 0.048); (b) between absent and extensive formation of osteophyte (P = 0.003), as well as between slight and extensive formation of osteophyte (P = 0.025); (c) between normal joint space and bony contact (P = 0.0002), as well as between reduced joint space and bony contact (P = 0.001).

CONCLUSIONS

Degenerative arthritis is an age-related disease. The progression and severity of osseous changes in the condylar head and mandibular fossa are increased with age. In older age groups, patients are expected to have more frequent and severe progressive degenerative bony changes due to the development of TMJ osteoarthritis than patients in younger age groups.

Conebeam CT of the head and neck, part 2: clinical applications

SUMMARY

Conebeam x-ray CT (CBCT) is being increasingly used for point-of-service head and neck and dentomaxillofacial imaging. This technique provides relatively high isotropic spatial resolution of osseous structures with a reduced radiation dose compared with conventional CT scans. In this second installment in a 2-part review, the clinical applications in the dentomaxillofacial and head and neck regions will be explored, with particular emphasis on diagnostic imaging of the sinuses, temporal bone, and craniofacial structures. Several controversies surrounding the emergence of CBCT technology will also be addressed.

Correlation of darkening of impacted mandibular third molar root on digital panoramic images with cone beam computed tomography findings

OBJECTIVES

Darkening of the lower third molar root on panoramic images is known to indicate an intimate relationship between the root and mandibular canal. The objective of this study was to investigate the anatomical relationship between the third molar root and its surrounding structures that leads to this panoramic finding.

METHODS

Imaging findings of 253 impacted lower third molars examined by both digital panoramic radiography and cone beam CT were reviewed. Panoramic images were evaluated to detect the presence or absence of darkening of the root where the mandibular canal was superimposed. Cone beam CT images were evaluated for the presence or absence of the following two findings: (1) grooving of the root and (2) thinning or perforation of the cortical plate by the root. The correlation between the panoramic and cone beam CT findings was examined using logistic regression analysis.

RESULTS

80 (32%) third molars showed a panoramic finding of darkening of the root. Between cone beam CT findings, cortical thinning or perforation alone was significantly correlated with this panoramic finding (80%, P < 0.001).

CONCLUSIONS

The panoramic finding of mandibular third molar root darkening was considered to reflect cortical thinning or perforation rather than grooving of the root.

Generation of three-dimensional prototype models based on cone beam computed tomography

PURPOSE

The purpose of this study was to generate three-dimensional models based on digital volumetric data that can be used in basic and advanced education.

METHODS

Four sets of digital volumetric data were established by cone beam computed tomography (CBCT) (Accuitomo, J. Morita, Kyoto, Japan). Datasets were exported as Dicom formats and imported into Mimics and Magic software programs to separate the different tissues such as nerve, tooth and bone. These data were transferred to a Polyjet 3D Printing machine (Eden 330, Object, Israel) to generate the models.

RESULTS

Three-dimensional prototype models of certain limited anatomical structures as acquired volumetrically were fabricated.

CONCLUSIONS

Generating three-dimensional models based on CBCT datasets is possible. Automated routine fabrication of these models, with the given infrastructure, is too time-consuming and therefore too expensive.

Histological investigation of osseous changes of mandibular condyles with backscattered electron images

OBJECTIVES

This study aims to confirm the radiographic morphology of mandibular condyles with microscopic observation and to investigate the mechanism of osseous changes of adult human mandibular condyles.

METHODS

Following the radiographic examinations of ten temporomandibular joints (TMJs) from five cadavers using conventional tomography, helical CT and limited cone beam CT for dentistry (limited CBCT), ten mandibular condyles were removed. Micro CT images were made of the undecalcified dissected joints in the sagittal plane, perpendicular to the long axis of the condyles, to produce images similar in orientation to the radiographic images. Tissue morphology was observed through backscattered electron images and elemental analysis using electron probe microanalysis (EPMA). The microscopic findings were compared with the radiographic findings.

RESULTS

Limited CBCT images most accurately depicted erosive change of the bone cortex of the mandibular condyle. EPMA indicated bone remodelling in all mandibular condyles analysed, which showed cartilage calcification different from typical enchondral ossification. No finding of dissolution or disruption of the superficial soft tissue was observed in all specimens, including those presenting radiographic findings of osteoarthrosis. Active bone remodelling with hypertrophic changes of superficial soft tissue was observed in mandibular condyles, which implied radiographic findings of osteoarthrosis.

CONCLUSIONS

The high detectability of limited CBCT images on bony morphology of mandibular condyles was confirmed. It is speculated that bone remodelling of adult human mandibular condyles is brought about by cartilage calcification. It was suggested that the osseous changes classified as osteoarthrosis with radiographic images are normal bone remodelling.

Comparison of image validity between cone beam computed tomography for dental use and multidetector row helical computed tomography

OBJECTIVES

To evaluate and compare the image validity of a cone beam CT machine for dental use (3DX) and the latest medical CT system, multidetector row helical CT (MDCT).

METHODS

A dried right maxilla of an Asian adult was used as a phantom. It was cut from the zygomatic process towards the midline, parallel to the midline plane, into eight slices of 2 mm thickness. This phantom was imaged with the 3DX and MDCT machines. Images were evaluated by comparing them with one selected bone slice from the phantom. In this comparison, two types of MDCT images were used: one with the window level (WL) and window width (WW) suitable for observing teeth (MDCT tooth image), and the other appropriate for observing bone (MDCT bone image). Three dentists and one radiographer then used our reported subjective five-level scale to evaluate and compare images generated by the two systems in terms of validity. Cancellous bone as well as enamel, dentin, pulp cavity, periodontal ligament space, lamina dura and overall impression were evaluated.

RESULTS

Statistically significant differences (P<0.05) were found for almost all observation items. Our subjective evaluation clarified that 3DX was superior to MDCT in terms of image validity. Few significant intra- or interevaluator errors were found.

CONCLUSIONS

Our subjective evaluation of image validity clarified 3DX as being superior to MDCT. Taken together with the low skin dose we previously reported for 3DX, the results demonstrate 3DX to be beneficial for imaging diagnosis of hard tissues in the maxillofacial region.

Beam hardening artefacts occur in dental implant scans with the NewTom cone beam CT but not with the dental 4-row multidetector CT

OBJECTIVES

The aim of this study was to examine beam hardening artefacts of the NewTom 9000 cone-beam computed tomography (CBCT) device compared with the Philips MX 8000 (4-row multidetector CT (MDCT)).

METHODS

We modified a SawBone skull to become a standardized model for our study. The skull was used for scans with the NewTom 9000 CBCT device and a standard dental multi-detector CT (MDCT) at a comparable reconstruction resolution with a standard Straumann ITI 4.1 mm implant in four implant positions in the maxilla (first permanent premolar in the right maxilla region, second permanent molar in the right maxilla region, first permanent premolar in the left maxilla region and second permanent molar in the left maxilla region). Results were compared with construction data of the dental implant. An image quality assessment of the images from both devices was performed with four experienced physicians and statistically analysed with the two-tailed Wilcoxon test.

RESULTS

Scans with the NewTom 9000 CBCT showed strong beam hardening artefacts in the form of a radiation beam shadow in all reconstructions compared with the MDCT. These imaging artefacts became stronger with greater distance from the centre of the scanned volume. These differences in the imaging quality were proved as significant in a quality evaluation by four experienced physicians (P<0.05).

CONCLUSIONS

Visual spatial resolution of the NewTom 9000 CBCT was less accurate than the Philips MX 8000 MDCT in the imaging of metallic dental implants.

Relationship between patient characteristics, mandibular head morphology and thickness of the roof of the glenoid fossa in symptomatic temporomandibular joints

OBJECTIVE

The purpose of this clinical study was to investigate the minimum thickness of the roof of the glenoid fossa (RGF) of grossly normal temporomandibular joints (TMJ) and to correlate this with patient gender, age and the morphological classification of the mandibular head.

METHODS

The study was performed on 191 TMJs from 109 patients (25 male and 84 female, age range 3-79 years, mean age 28.1 years) who visited Nihon University Dental Hospital, Japan with suspected TMJ disorders. The patients underwent cone beam computed tomography (3DX CT) to enable observation of the morphological features of the mandibular head. The minimum thickness of the RGF was measured using frontal section images acquired by CT. The morphology of the mandibular heads was classified according to the method of Yale and colleagues. Mean linear measurements were used for statistical analyses of patient gender, age and mandibular head morphology.

RESULTS

The average minimum thickness of the RGF was 0.79 mm. No significant difference in thickness was found between male and female patients. In addition, no differences were recorded as a result of variation in age or mandibular head morphology.

CONCLUSIONS

These results indicate that RGF thickness is not significantly correlated with gender, age, or mandibular head morphology, at least in this cohort of patients.

The 3DX multi image micro-CT device in clinical dental practice

OBJECTIVES

To evaluate the usefulness of 3DX multi-image micro-CT device in clinical dental practice.

METHODS

Images of 198 examinations performed with a 3DX device during a 6 month period in a private dental practice were evaluated retrospectively for the benefit of additional information compared with panoramic or intraoral radiographs.

RESULTS

The main indication for the use of 3DX micro-CT was planning of dental implant placement in 49% of the examinations. Diagnosis or exclusion of dental infection or peri-implantitis represented 28% of the examinations and tooth, root or foreign body localization represented 13%. Temporomandibular joint (TMJ) imaging and cyst or tumour diagnosis represented 7.5% and 2.5% of the examinations, respectively. In implant planning and tooth, root or foreign body localization examinations, the required information was obtained in every case except three implant planning examinations, in which the exact measurements were hampered by artefacts caused by root fillings and retrograde fillings or metal posts. When compared with conventional radiography, additional radiographic information was obtained in 51% of the micro-CT examinations performed to confirm or exclude dental infection or peri-implantitis. Micro-CT also showed the bone structure of TMJs precisely.

CONCLUSIONS

The 3DX micro-CT device visualizes bony anatomical structures precisely, which makes it a reliable tool for, for example, planning of implant treatment. The device is highly suitable for diagnosing dental infections. Dental restorations may cause disturbing artefacts and in 4.5% of the examinations the small imaging area resulted in re-examination.

Reproducibility and accuracy of measuring unerupted teeth using limited cone beam X-ray CT

OBJECTIVE

The purpose of this investigation was to determine the reproducibility among observers and accuracy of the measurement of the tooth crown width of unerupted teeth using limited area cone beam X-ray CT.

METHODS

3DX multi-image micro-CT (3DX, Morita Co., Kyoto, Japan) images of impacted supernumerary teeth in the median maxillary region taken prior to extraction were used for the samples. The width of the tooth on the 3DX image was measured five times by five individual observers. Significant differences in values among the observers in the measurement were determined by one-way analysis of variance for examining reproducibility. The measurement results of the ten samples on 3DX images were compared with the laboratory measurements using a three-dimensional co-ordinate measuring apparatus, using the Wilcoxon signed-rank sum test.

RESULTS

There was no significant difference among the observers in the measurement (P>0.05). The measurement results shown on 3DX images were significantly larger than those of the laboratory measurements (P<0.05). The mean difference was +0.088 mm.

CONCLUSIONS

3DX has high reproducibility for measuring the tooth crown width of unerupted teeth. While 3DX measurement values were larger than the laboratory measurements, the difference is clinically insignificant.

Accuracy of three-dimensional measurements using cone-beam CT

OBJECTIVES

Lesions causing intraosseous defects in the head and neck region are difficult to diagnose using two-dimensional radiography, and three-dimensional (3D) data provided by CT is useful but often difficult to obtain. Recently, cone-beam CT (CBCT) was made available, with the potential to become a practical tool in dentistry. However, there is limited evidence to prove that defect volume can be determined accurately. Therefore, this in vitro validation study aimed at establishing whether linear and 3D CBCT, using volumetric measurements, is accurate for determining osseous defect sizes.

METHODS

Depth and diameter of simulated bone defects in (i) an acrylic block and (ii) a human mandible were blindly measured electronically by five examiners using CBCT. Linear measurements were compared with predetermined machined dimensions. Using software, volume extraction was performed by another examiner on the acrylic phantom and compared with known dimensions. Data were analysed using paired t-tests.

RESULTS

Using the acrylic block, mean width accuracy was -0.01 mm (+/- 0.02 SE) and mean height difference was -0.03 mm (+/- 0.01 SE; P > 0.05). For the human mandible, mean width accuracy was -0.07 mm (+/- 0.02 SE) and mean height accuracy was -0.27 mm (+/- 0.02 SE; P < 0.01). Volume accuracy was -6.9 mm3 (+/- 4 SE) for automated calculations and -2.3 mm3 (+/- 2.6 SE) for the manual measurements (P < 0.001).

CONCLUSIONS

CBCT has the potential to be an accurate, non-invasive, practical method to reliably determine osseous lesion size and volume. Further clinical validation will lead to a vast array of applications in oral and maxillofacial diagnosis.

The thickness of the roof of the glenoid fossa in the temporomandibular joint: relationship to the MRI findings

OBJECTIVES

The purpose of this study was to clarify the relationship between the thickness of the roof of the glenoid fossa (RGF) and magnetic resonance imaging (MRI) findings of temporomandibular joint (TMJ) disorders (TMDs).

METHODS

Eighty-seven patients with symptoms and indications of TMD in one or both TMJs were referred for MRI. Cone-beam CT (3DX) was used to measure the thickness of the RGF at its thinnest point. Linear measurements were made three times on the monitor by three separate investigators and the mean values obtained were used for the statistical analyses.

RESULTS

The joints were categorised as normal (70 joints), anterior disc displacement with reduction (ADWR; 53 joints) or anterior disc displacement without reduction (ADWOR; 51 joints). The joint disorders were also categorised into the following subgroups: with osteoarthritis (OA) (21 joints), without OA (153 joints), with disc deformation (33 joints), without disc deformation (141 joints), with joint effusion (JE) (61 joints) and without JE (113 joints). The average minimum thickness of the RGF was 0.85 mm for normal joints, 0.90 mm with ADWR, 0.93 mm with ADWOR, 0.99 mm with OA, 0.87 mm without OA, 0.87 mm with disc deformation and 0.89 mm without disc deformation. There was no significant difference between these figures. There was a significant difference in the thickness of the RGF with (0.97 mm) and without (0.84 mm) JE.

CONCLUSIONS

These results suggest that RGF thickness is influenced by JE, but is unaffected by disc position and configuration.

Osseous abnormalities of the mandibular condyle: diagnostic reliability of cone beam computed tomography compared with helical computed tomography based on an autopsy material

OBJECTIVES

We compared the diagnostic reliability of cone beam computed tomography (3DX) and helical computed tomography (helical CT) for the detection of osseous abnormalities of the mandibular condyle, using macroscopic observations as the gold standard.

METHODS

Twenty-one temporomandibular joint autopsy specimens underwent imaging with 3DX and helical CT. The specimens were macroscopically evaluated for cortical erosion or osteophytosis and sclerosis. The images were independently assessed for the same osseous abnormalities. Observations with the two imaging modalities were compared with the macroscopic observations using the McNemar test.

RESULTS

According to the macroscopic observations, 10 of the 21 mandibular condyles and one fossa showed osseous abnormalities. 3DX detected abnormalities in eight of these condyles and helical CT identified abnormalities in seven, giving a sensitivity of 0.80 for 3DX and 0.70 for helical CT. The specificity of the condyle assessment was 1.0 for both 3DX and helical CT and hence, the accuracy was 0.90 and 0.86, respectively. No significant differences were detected between the 3DX and helical CT for assessment of osseous abnormalities of the mandibular condyle (P=0.286).

CONCLUSIONS

The cone beam CT equipment 3DX is a dose-effective and a cost-effective alternative to helical CT for the diagnostic evaluation of osseous abnormalities of the mandibular condyle.

Value of digital volume tomography in patients with conductive hearing loss

Digital volume tomography (DVT) is an extension of panoramic tomography. With this diagnostic technique, characterized by high resolution, a narrow section width (0.125 mm) and three-dimensional display, small pathological processes can be well visualized. Twenty-five patients with the history of a progressive hearing loss were examined with DVT (Accu-I-tomo, Morita, Japan). The results were compared with pre- and intraoperative findings to evaluate the diagnostic value of DVT in cases of erosion of the ossicular chain. With high resolution and artifact-free demonstration of the middle ear and the ossicular chain, it was possible to define its continuity preoperatively by DVT in all 25 cases. An intact ossicular chain was found by DVT in 13 cases and was later confirmed by surgery. The predicted erosion of the ossicles was verified in 12 patients, and a tympanoplasty type III was performed. Digital volume tomography is an excellent technique to examine the middle ear cleft and inner ear, and expands the application of diagnostic possibilities in the lateral skull base. Therefore, improvement in preoperative diagnosis is achieved along with more accurate planning of the surgical procedure. Digital volume tomography delivers a small radiation dose with a high resolution and a low purchase price for the equipment.

Using a flat-panel detector in high resolution cone beam CT for dental imaging

OBJECTIVES

Cone beam CT (CBCT) requires a two-dimensional X-ray detector. In the several CBCT systems developed for dental imaging, detection has been by the combination of an X-ray image intensifier and charge-coupled device (CCD) camera. In this paper, we propose a new CBCT system in which the detector is of the flat-panel type and evaluate its performance in dental imaging.

METHODS

We developed a prototype CBCT that has a flat-panel-type detector. The detector consists of a CsI scintillator screen and a photosensor array. First, the flat panel detector and image intensifier detector were compared in terms of the signal-to-noise ratio (SNR) of projected images. We then used these data and a theoretical formula to evaluate noise in reconstructed images. Second, reconstructed images of a bar pattern phantom were obtained as a way of evaluating the spatial resolution. Then, reconstructed images of a skull phantom were obtained.

RESULTS

The SNR of the developed system was 1.6 times as high as that of a system with an image intensifier detector of equal detector pitch. The system was capable of resolving a 0.35 mm pattern and its field of view almost completely encompassed that of an image intensifier detector which is used in dentomaxillofacial imaging. The fine spatial resolution of the detector led to images in which the structural details of a skull phantom were clearly visible.

CONCLUSIONS

The system's isotropically fine resolution will lead to improved precision in dental diagnosis and surgery. The next stage of our research will be the development of a flat panel detector system with a high frame acquisition rate.

Geometric accuracy of the NewTom 9000 Cone Beam CT

OBJECTIVES

To determine the geometric accuracy of digital volume tomograms to assess their usability for implant planning.

METHODS

A measuring object with 216 measuring points, whose geometry is exactly known, is X-rayed with a NewTom 9000 cone beam scanner; thereafter the geometry of the volume tomogram of the object is compared with the original body.

RESULTS

Considering all three coordinate axes, geometric mean deviations of 0.13 +/- 0.09 mm with a maximum deviation of 0.3 mm were determined. These geometric deviations are below the resolution power of the volume tomograph.

CONCLUSION

The digital volume tomographies of NewTom 9000 present images which are geometrically correct and, from a geometrical point of view, suitable for three-dimensional implant planning.

Characteristics of a newly developed dentomaxillofacial X-ray cone beam CT scanner (CB MercuRay): system configuration and physical properties

OBJECTIVE

The purpose of this paper is to present the system configuration and physical properties of a new dentomaxillofacial X-ray cone beam CT system (CB MercuRay) being developed.

METHODS

The system consists of an image intensifier and a cone beam X-ray source. There are two different models of this system, each with a different size image intensifier, 9" or 12". Each system has three field of view (FOV) modes. The 12" system has facial (F), panoramic (P) and implant (I) FOV modes. The 9" system has P, I and dental (D) modes. Images produced by these systems consist of 512 x 512 x 512 isotropic voxels. Physical properties such as resolution, noise and distortion of the images were evaluated in this study. Modulation transfer function (MTF) was measured using Boone's method. Image noise was measured as the standard deviation of the CT value in water. Circularity of the axial images yielded by the two models was measured using an 8 mm diameter acrylic pipe phantom.

RESULTS

The resolving power at a MTF of 0.1 in the D mode was over 2.0 lp mm(-1), suggesting that this system yields images of high resolution. The standard deviation of the CT value in water was approximately 80, which is thought to be greater than that of conventional CT. The circularity of images of the pipe phantom was 99% of the ideal value.

CONCLUSION

This study shows that our newly developed cone beam CT system produces high resolution three-dimensional volumetric images that will be useful for the examination of dentomaxillofacial disorders.