Interface engineering of layer-by-layer stacked graphene anodes for high-performance organic solar cells

13.7 % Efficient Graphene/Si Heterojunction Solar Cells with One-Step Transferred Polymer Anti-Reflection Layer for Enhanced Light Absorption and Device Durability

Graphene/Silicon (Gr/Si) heterojunction shows great potential as high-efficiency, cost-effective solar cells compared to traditional Si solar cells. However, the high optical loss of c-Si, mainly originating from abrupt change of refractive index at air/Si interface, and the unsatisfactory conductivity of practically prepared graphene layer, still hinder their extensive applications. Herein, we report the performance improved Gr/Si solar cells by depositing a polymathic methacrylate (PMMA) anti-reflection coating (ARC) layer through a one-step transferred method. The graphene and PMMA ARC with specific thickness were transferred on n-type Si wafer at the same time, which reduces production steps and obtains high-quality graphene layer. By tuning the thickness of the PMMA layer, the reflection can be reduced obviously. Companying with the HNO3 vapor doping for graphene, the Gr/Si heterojunction solar cell with a high power conversion efficiency (PCE) of 13.7 % was achieved. In addition, the durability of the device is improved under HNO3 doping. Considering the easy and cost-effective solution processed capability of the one-step transferred graphene and PMMA ARC layer, we believed that PMMA/Gr/Si is a feasible low-temperature technique for high-efficiency Si solar cells.

Multilayer Graphene Stacked with Silver Nanowire Networks for Transparent Conductor

A mechanically robust flexible transparent conductor with high thermal and chemical stability was fabricated from welded silver nanowire networks (w-Ag-NWs) sandwiched between multilayer graphene (MLG) and polyimide (PI) films. By modifying the gas flow dynamics and surface chemistry of the Cu surface during graphene growth, a highly crystalline and uniform MLG film was obtained on the Cu foil, which was then directly coated on the Ag-NW networks to serve as a barrier material. It was found that the highly crystalline layers in the MLG film compensate for structural defects, thus forming a perfect barrier film to shield Ag NWs from oxidation and sulfurization. MLG/w-Ag-NW composites were then embedded into the surface of a transparent and colorless PI thin film by spin-coating. This allowed the MLG/w-Ag-NW/PI composite to retain its original structural integrity due to the intrinsic physical and chemical properties of PI, which also served effectively as a binder. In view of its unique sandwich structure and the chemical welding of the Ag NWs, the flexible substrate-cum-electrode had an average sheet resistance of ≈34 Ω/sq and a transmittance of ≈91% in the visible range, and also showed excellent stability against high-temperature annealing and sulfurization.

Interface Engineering for Highly Efficient Organic Solar Cells

Organic solar cells (OSCs) have made dramatic advancements during the past decades owing to the innovative material design and device structure optimization, with power conversion efficiencies surpassing 19% and 20% for single-junction and tandem devices, respectively. Interface engineering, by modifying interface properties between different layers for OSCs, has become a vital part to promote the device efficiency. It is essential to elucidate the intrinsic working mechanism of interface layers, as well as the related physical and chemical processes that manipulate device performance and long-term stability. In this article, the advances in interface engineering aimed to pursue high-performance OSCs are reviewed. The specific functions and corresponding design principles of interface layers are summarized first. Then, the anode interface layer, cathode interface layer in single-junction OSCs, and interconnecting layer of tandem devices are discussed in separate categories, and the interface engineering-related improvements on device efficiency and stability are analyzed. Finally, the challenges and prospects associated with application of interface engineering are discussed with the emphasis on large-area, high-performance, and low-cost device manufacturing.

Dynamically tunable multifunctional terahertz absorber based on hybrid vanadium dioxide and graphene metamaterials

In this work, in pursuit of a multifunctional device with a simple structure, high absorption rate, and excellent bandwidth, a tunable broadband terahertz (THz) absorber based on vanadium dioxide (V O 2) and graphene is proposed. Due to the phase transition of V O 2 and the electrically tunable properties of graphene, the structure realizes single broadband and dual-band absorption characteristics. When graphene is in the insulating state (E f=0e V) and V O 2 is in the metallic state, the developed system has more than 90% absorption and a wide absorption band from 1.36 to 5.48 THz. By adjusting the V O 2 conductivity, the bandwidth absorption can be dynamically varied from 23% to more than 90%, which makes it a perfect broadband absorber. When graphene is in the metallic state (E f=1e V), V O 2 is in the insulating state, and the designed device behaves as a tunable and perfect dual-band absorber, where the absorptivity of the dual-band spectrum can be continuously adjusted by varying the Fermi energy level of graphene. In addition, both the broad absorption spectrum and the dual-band absorption spectrum maintain strong polarization-independent properties and operate well over a wide incidence angle, and the designed system may provide new avenues for the development of terahertz and other frequency-domain tunable devices.

Advances in Smart Photovoltaic Textiles

Energy harvesting textiles have emerged as a promising solution to sustainably power wearable electronics. Textile-based solar cells (SCs) interconnected with on-body electronics have emerged to meet such needs. These technologies are lightweight, flexible, and easy to transport while leveraging the abundant natural sunlight in an eco-friendly way. In this Review, we comprehensively explore the working mechanisms, diverse types, and advanced fabrication strategies of photovoltaic textiles. Furthermore, we provide a detailed analysis of the recent progress made in various types of photovoltaic textiles, emphasizing their electrochemical performance. The focal point of this review centers on smart photovoltaic textiles for wearable electronic applications. Finally, we offer insights and perspectives on potential solutions to overcome the existing limitations of textile-based photovoltaics to promote their industrial commercialization.

A review on adsorption of heavy metals from wastewater using carbon nanotube and graphene-based nanomaterials

The rampant rise in world population, industrialization, and urbanization expedite the contamination of water sources. The presence of the non-biodegradable character of heavy metals in waterways badly affects the ecological balance. In this modern era, the unavailability of getting clear water as well as the downturn in water quality is a major concern. Therefore, the effective removal of heavy metals has become much more important than before. In recent years, the attention to better wastewater remediation was directed towards adsorption techniques with novel adsorbents such as carbon nanomaterials. This review paper primarily emphasizes the fundamental concepts, structures, and unique surface properties of novel adsorbents, the harmful effects of various heavy metals, and the adsorption mechanism. This review will give an insight into the current status of research in the realm of sustainable wastewater treatment, applications of carbon nanomaterials, different types of functionalized carbon nanotubes, graphene, graphene oxide, and their adsorption capacity. The importance of MD simulations and density functional theory (DFT) in the elimination of heavy metals from aqueous media is also discussed. In addition to that, the effect of factors on heavy metal adsorption such as electric field and pressure is addressed.

Evaluation of transmission characteristics of CVD-grown graphene and effect of tuning electrical properties of graphene up to 50 GHz

Graphene has been investigated as a transparent conductive film for use in a variety of devices, and in recent years it has shown promise for use in millimeter-wave devices as 5G technology. In this study, we applied single-layer (SL), triple-layer (3L), and P-type doped 3L graphene to coplanar waveguide (CPW) transmission lines and obtained transmission characteristics (S21) from 1 to 50 GHz, which covered the 5G band. Furthermore, an equivalent circuit model of the CPW used in the measurements was constructed and simulations were performed, which showed good agreement with the measured results. The results validated the transmission properties of the graphene and the contact impedance at the interface between electrodes and the graphene in CPW circuits, which are necessary parameters for designing antennas using graphene. In addition, by comparing the transmission loss of three types of graphene, the parameters for improving the transmission characteristics were clarified.

Determination of the preferred epitaxy for III-nitride semiconductors on wet-transferred graphene

Transferred graphene provides a promising III-nitride semiconductor epitaxial platform for fabricating multifunctional devices beyond the limitation of conventional substrates. Despite its tremendous fundamental and technological importance, it remains an open question on which kind of epitaxy is preferred for single-crystal III-nitrides. Popular answers to this include the remote epitaxy where the III-nitride/graphene interface is coupled by nonchemical bonds, and the quasi-van der Waals epitaxy (quasi-vdWe) where the interface is mainly coupled by covalent bonds. Here, we show the preferred one on wet-transferred graphene is quasi-vdWe. Using aluminum nitride (AlN), a strong polar III-nitride, as an example, we demonstrate that the remote interaction from the graphene/AlN template can inhibit out-of-plane lattice inversion other than in-plane lattice twist of the nuclei, resulting in a polycrystalline AlN film. In contrast, quasi-vdWe always leads to single-crystal film. By answering this long-standing controversy, this work could facilitate the development of III-nitride semiconductor devices on two-dimensional materials such as graphene.

Field and Thermal Emission Limited Charge Injection in Au-C60-Graphene van der Waals Vertical Heterostructures for Organic Electronics

Among the family of 2D materials, graphene is the ideal candidate as top or interlayer electrode for hybrid van der Waals heterostructures made of organic thin films and 2D materials due to its high conductivity and mobility and its inherent ability of forming neat interfaces without diffusing in the adjacent organic layer. Understanding the charge injection mechanism at graphene/organic semiconductor interfaces is therefore crucial to develop organic electronic devices. In particular, Gr/C60 interfaces are promising building blocks for future n-type vertical organic transistors exploiting graphene as tunneling base electrode in a two back-to-back Gr/C60 Schottky diode configuration. This work delves into the charge transport mechanism across Au/C60/Gr vertical heterostructures fabricated on Si/SiO₂ using a combination of techniques commonly used in the semiconductor industry, where a resist-free CVD graphene layer functions as a top electrode. Temperature-dependent electrical measurements show that the transport mechanism is injection limited and occurs via Fowler-Nordheim tunneling at low temperature, while it is dominated by a nonideal thermionic emission at room and high temperatures, with energy barriers at room temperature of ca. 0.58 and 0.65 eV at the Gr/C60 and Au/C60 interfaces, respectively. Impedance spectroscopy confirms that the organic semiconductor is depleted, and the energy band diagram results in two electron blocking interfaces. The resulting rectifying nature of the Gr/C60 interface could be exploited in organic hot electron transistors and vertical organic permeable-base transistors.

Green engineering of TMC-CMS nanoparticles decorated graphene sheets for targeting M. tuberculosis

Our current work intends to primarily engineer a new type of antibacterial composite by preparing a highly biocompatible graphene sheet decorated with TMC-CMS IPNs nanoparticles utilizing one-pot, green, cost-effective ultrasonication approach. The microstructure of as-formed materials was chemically confirmed using various analytical techniques such as ¹H-NMR, FTIR, UV/vis, SEM, and TEM. TEM data has proved the formation of uniformly distributed TCNPs on graphene surfaces with a small particle size of ~22 nm compared with that of pure nanoparticles (~30 nm). The inhibitory activity of these developed materials was examined against the growth of three different M. tuberculosis pathogens and in a comparison with the isoniazid drug as a standard anti-tuberculosis drug. The TCNPs@GRP composite attained MIC values of 0.98, 3.9, and 7.81 μg/mL for inhibiting the growth of sensitive, MDR, and XDR M. tuberculosis pathogens compared to the bare TCNPs (7.81, 31.25, >125 μg/mL) and the isoniazid drug (0.24, 0, 0 μg/mL), respectively. This reveals a considerable synergism in the antituberculosis activity between TCNPs and graphene nanosheets. Cytotoxicity of the TCNPs@GRP was examined against normal lung cell lines (WI38) and was found to have cell viability of 100% with the concentration range of 0.98-7.81 μg/mL.

Charge Transport Across Au-P3HT-Graphene van der Waals Vertical Heterostructures

Hybrid van der Waals heterostructures based on 2D materials and/or organic thin films are being evaluated as potential functional devices for a variety of applications. In this context, the graphene/organic semiconductor (Gr/OSC) heterostructure could represent the core element to build future vertical organic transistors based on two back-to-back Gr/OSC diodes sharing a common graphene sheet, which functions as the base electrode. However, the assessment of the Gr/OSC potential still requires a deeper understanding of the charge carrier transport across the interface as well as the development of wafer-scale fabrication methods. This work investigates the charge injection and transport across Au/OSC/Gr vertical heterostructures, focusing on poly(3-hexylthiophen-2,5-diyl) as the OSC, where the PMMA-free graphene layer functions as the top electrode. The structures are fabricated using a combination of processes widely exploited in semiconductor manufacturing and therefore are suited for industrial upscaling. Temperature-dependent current-voltage measurements and impedance spectroscopy show that the charge transport across both device interfaces is injection-limited by thermionic emission at high bias, while it is space charge limited at low bias, and that the P3HT can be assumed fully depleted in the high bias regime. From the space charge limited model, the out-of-plane charge carrier mobility in P3HT is found to be equal to μ ≈ 2.8 × 10^-4 cm² V^-1 s^-1, similar to the in-plane mobility reported in previous works, while the charge carrier density is N₀ ≈ 1.16 × 10¹⁵ cm^-3, also in agreement with previously reported values. From the thermionic emission model, the energy barriers at the Gr/P3HT and Au/P3HT interfaces result in 0.30 eV and 0.25 eV, respectively. Based on the measured barriers heights, the energy band diagram of the vertical heterostructure is proposed under the hypothesis that P3HT is fully depleted.

Graphene: A Path-Breaking Discovery for Energy Storage and Sustainability

The global energy situation requires the efficient use of resources and the development of new materials and processes for meeting current energy demand. Traditional materials have been explored to large extent for use in energy saving and storage devices. Graphene, being a path-breaking discovery of the present era, has become one of the most-researched materials due to its fascinating properties, such as high tensile strength, half-integer quantum Hall effect and excellent electrical/thermal conductivity. This paper presents an in-depth review on the exploration of deploying diverse derivatives and morphologies of graphene in various energy-saving and environmentally friendly applications. Use of graphene in lubricants has resulted in improvements to anti-wear characteristics and reduced frictional losses. This comprehensive survey facilitates the researchers in selecting the appropriate graphene derivative(s) and their compatibility with various materials to fabricate high-performance composites for usage in solar cells, fuel cells, supercapacitor applications, rechargeable batteries and automotive sectors.

Characterization of encapsulated graphene layers using extreme ultraviolet coherence tomography

Many applications of two-dimensional materials such as graphene require the encapsulation in bulk material. While a variety of methods exist for the structural and functional characterization of uncovered 2D materials, there is a need for methods that image encapsulated 2D materials as well as the surrounding matter. In this work, we use extreme ultraviolet coherence tomography to image graphene flakes buried beneath 200 nm of silicon. We show that we can identify mono-, bi-, and trilayers of graphene and quantify the thickness of the silicon bulk on top by measuring the depth-resolved reflectivity. Furthermore, we estimate the quality of the graphene interface by incorporating a model that includes the interface roughness. These results are verified by atomic force microscopy and prove that extreme ultraviolet coherence tomography is a suitable tool for imaging 2D materials embedded in bulk materials.

Low-Temperature CVD-Grown Graphene Thin Films as Transparent Electrode for Organic Photovoltaics

Good conductivity, suitable transparency and uniform layers of graphene thin film can be produced by chemical vapour deposition (CVD) at low temperature and utilised as a transparent electrode in organic photovoltaics. Using chlorobenzene trapped in poly(methyl methacrylate) (PMMA) polymer as the carbon source, growth temperature (Tgrowth) of 600 °C at hydrogen (H2) flow of 75 standard cubic centimetres per minute (sccm) was used to prepare graphene by CVD catalytically on copper (Cu) foil substrates. Through the Tgrowth of 600 °C, we observed and identified the quality of the graphene films, as characterised by Raman spectroscopy. Finally, P3HT (poly (3-hexylthiophene-2, 5-diyl)): PCBM (phenyl-C61-butyric acid methyl ester) bulk heterojunction solar cells were fabricated on graphene-based window electrodes and compared with indium tin oxide (ITO)-based devices. It is interesting to observe that the OPV performance is improved more than 5 fold with increasing illuminated areas, hinting that high resistance between graphene domains can be alleviated by photo generated charges.

Effects of adatom species on the structure, stability, and work function of adatom-α-borophene nanocomposites

Work function-tunable borophene-based electrode materials are of significant importance because they promote efficient carrier extraction/injection, thereby enabling electronic devices to achieve maximum energy conversion efficiency. Accordingly, determining the work function of adatom-borophene nanocomposites within a series wherein the adatom is systematically changed will facilitate the design of such materials. In this study, we theoretically determined that the M-B bond length, binding energy, electron transfer between adatoms and BBP, and work function (ϕ) are linearly dependent on the ionization potential (IP) and electronegativity for thermodynamically and kinetically stable adatom-α-borophene (M/BBP) systems involving a series of alkali (earth) metal/BBP (M = Li-Cs; Be-Ba) and halogen/BBP (M = F-I), respectively. However, the binding energies of Li/BBP and Be/BBP deviate from these dependencies owing to their super small adatoms and the resulting significantly enhanced effective M-B bonding areas. By interpreting the electron transfer picture among the different parts of M/BBP, we confirmed that metallic M/BBP possesses ionic sp-p and dsp-p M-B bonds in alkali (earth) metal/BBP but covalent-featured ionic p-p interactions in halogen/BBP. In particular, the direct proportionality between IP and ϕ for alkali (earth) metal/BBP originates from the synergistic effect of charge rearrangement and the increased induced dipole moment; however, the inverse proportionality between electronegativity and ϕ for halogen/BBP arises from the adsorption induced charge redistribution. Our results provide guidance for experimental efforts toward the realization of work function-tunable borophene-based electrodes as well as insight into the bonding rules between various adatoms and α-borophene.

Graphene with Ni-Grid as Semitransparent Electrode for Bulk Heterojunction Solar Cells (BHJ-SCs)

In this work, we present the fabrication and characterization of bulk-heterojunction solar cells on monolayer graphene (MLG) with nickel-grids (Ni-grid) as semitransparent conductive electrode. The electrodes showed a maximum transmittance of 90% (calculated in 300–800 nm range) and a sheet resistance down to 35 Ω/□. On these new anodes, we fabricated TCO free BHJ-SCs using PTB7 blended with PC70BM fullerene derivative as active layer. The best device exhibited a power conversion efficiency (PCE) of 4.2% in direct configuration and 3.6% in inverted configuration. The reference solar cell, realized on the ITO glass substrate, achieved a PCE of 6.1% and 6.7% in direct and inverted configuration respectively; for comparison we also tested OSCs only with simple Ni-grid as semitransparent and conductive electrode, obtaining a low PCE of 0.7%. The proposed approach to realize graphene-based electrodes could be a possible route to reduce the overall impact of the sheet resistance of this type of electrodes allowing their use in several optoelectronic devices.

Application of Graphene-Related Materials in Organic Solar Cells

Graphene-related materials (GRMs) such as graphene quantum dots (GQDs), graphene oxide (GO), reduced graphene oxide (rGO), graphene nanoribbons (GNRs), and so forth have recently emerged as photovoltaic (PV) materials due to their nanodimensional structure and outstanding properties such as high electrical and thermal conductivity, large specific surface, and unique combination of mechanical strength and flexibility. They can be a crucial part of transparent electrodes, hole/electron transport materials, and active layers in organic solar cells (OSCs). Besides their role in charge extraction and transport, GRMs act as device protectors against environmental degradation through their compact bidimensional structure and offer good durability. This review briefly presents the synthesis methods of GRMs and describes the current progress in GRM-based OSCs. PV parameters (short circuit current, open circuit voltage, power conversion efficiency, and fill factor) are summarized and comparatively discussed for the different structures. The efficiency recently surpassed 15% for an OSC incorporating polymer-modified graphene as a transparent electrode. The long-term stability of OSCs incorporating GRMs is also discussed. Finally, conclusions and the outlook for future investigation into GRM-based devices for PVs are presented.

Transparent graphene electrodes based hybrid perovskites photodetectors with broad spectral response from UV-visible to near-infrared

A new class of transparent graphene electrode based organic-inorganic halide perovskite photodetectors with broad spectral response is developed. These ultrasensitive devices exhibit high ON/OFF current ratio, high linear dynamic range, broad spectral range, excellent detection for weak light and easy fabrication with low-cost. Their semi-transparent feature and distinct photodetecting function for both sides would provide new applications affecting our daily lives.

Solution-processed two-dimensional materials for next-generation photovoltaics

In the ever-increasing energy demand scenario, the development of novel photovoltaic (PV) technologies is considered to be one of the key solutions to fulfil the energy request. In this context, graphene and related two-dimensional (2D) materials (GRMs), including nonlayered 2D materials and 2D perovskites, as well as their hybrid systems, are emerging as promising candidates to drive innovation in PV technologies. The mechanical, thermal, and optoelectronic properties of GRMs can be exploited in different active components of solar cells to design next-generation devices. These components include front (transparent) and back conductive electrodes, charge transporting layers, and interconnecting/recombination layers, as well as photoactive layers. The production and processing of GRMs in the liquid phase, coupled with the ability to "on-demand" tune their optoelectronic properties exploiting wet-chemical functionalization, enable their effective integration in advanced PV devices through scalable, reliable, and inexpensive printing/coating processes. Herein, we review the progresses in the use of solution-processed 2D materials in organic solar cells, dye-sensitized solar cells, perovskite solar cells, quantum dot solar cells, and organic-inorganic hybrid solar cells, as well as in tandem systems. We first provide a brief introduction on the properties of 2D materials and their production methods by solution-processing routes. Then, we discuss the functionality of 2D materials for electrodes, photoactive layer components/additives, charge transporting layers, and interconnecting layers through figures of merit, which allow the performance of solar cells to be determined and compared with the state-of-the-art values. We finally outline the roadmap for the further exploitation of solution-processed 2D materials to boost the performance of PV devices.

Imparting α-Borophene with High Work Function by Fluorine Adsorption: A First-Principles Investigation

Increasing the work function of borophene over a large range is crucial for the development of borophene-based anode materials for highly efficient electronic devices. In this study, the effect of fluorine adsorption on the structures and stabilities, particularly on the work function, of α-borophene (BBP), was systematically investigated via first-principles density functional theory. The calculations indicated that BBP was well-stabilized by fluorine adsorption and the work functions of metallic fluorine-adsorbed BBPs (F_n-BBPs) sharply increased with increasing fluorine content. Moreover, the work function of F-BBP was close to that of the frequently used anode material Au and even, for other F_n-BBPs, higher than that of Pt. Furthermore, we have comprehensively discussed the factors, including substrate deformation, charge transfer, induced dipole moment, and Fermi and vacuum energy levels, affecting the improvement of work function. Particularly, we have demonstrated that the charge redistribution of the substrate induced by the bonding interaction between fluorine and the matrix predominantly contributes to the observed increase in the work function. Additionally, the effect of fluorine adsorption on the increase in the work function of BBP was significantly stronger than that of silicene or graphene. Our results concretely support the fact that F_n-BBPs can be extremely attractive anode materials for electronic device applications.

Controllable Synthesis of Wafer-Scale Graphene Films: Challenges, Status, and Perspectives

The availability of high-quality, large-scale, and single-crystal wafer-scale graphene films is fundamental for key device applications in the field of electronics, optics, and sensors. Synthesis determines the future: unleashing the full potentials of such emerging materials relies heavily upon their tailored synthesis in a scalable fashion, which is by no means an easy task to date. This review covers the state-of-the-art progress in the synthesis of wafer-scale graphene films by virtue of chemical vapor deposition (CVD), with a focus on main challenges and present status. Particularly, prevailing synthetic strategies are highlighted on a basis of the discussion in the reaction kinetics and gas-phase dynamics during CVD process. Perspectives with respect to key opportunities and promising research directions are proposed to guide the future development of wafer-scale graphene films.

Review and comparison of layer transfer methods for two-dimensional materials for emerging applications

Two-dimensional (2D) materials offer immense potential for scientific breakthroughs and technological innovations. While early demonstrations of 2D material-based electronics, optoelectronics, flextronics, straintronics, twistronics, and biomimetic devices exploited micromechanically-exfoliated single crystal flakes, recent years have witnessed steady progress in large-area growth techniques such as physical vapor deposition (PVD), chemical vapor deposition (CVD), and metal-organic CVD (MOCVD). However, use of high growth temperatures, chemically-active growth precursors and promoters, and the need for epitaxy often limit direct growth of 2D materials on the substrates of interest for commercial applications. This has led to the development of a large number of methods for the layer transfer of 2D materials from the growth substrate to the target application substrate with varying degrees of cleanliness, uniformity, and transfer-related damage. This review aims to catalog and discuss these layer transfer methods. In particular, the processes, advantages, and drawbacks of various transfer methods are discussed, as is their applicability to different technological platforms of interest for 2D material implementation.

Switchable terahertz metamaterial absorber with broadband absorption and multiband absorption

Based on the phase-transition property of vanadium dioxide (VO₂), a terahertz bifunctional absorber is proposed with switchable functionalities of broadband absorption and multiband absorption. When VO₂ is metal, the system is regarded as a broadband absorber, which is composed of VO₂ patch, topas spacer, and VO₂ film with metallic disks inserted. The system obtains a broadband absorption with absorptance >90% from 3.25 THz to 7.08 THz. Moreover, the designed broadband absorber has a stable performance within the incident angle range of 50°. When VO₂ is dielectric, multiband absorption with six peaks is realized in the designed system. Graphene and the metallic disk-shaped array play the dominant role in the mechanism of multiband absorption. Through changing the Fermi energy level of graphene, the performance of multiband absorption can be dynamically adjusted. Because of the switchable functionalities, the proposed design may have potential application in the fields of intelligent absorption and terahertz switch.

Progress and Prospects on the Fabrication of Graphene-Based Nanostructures for Energy Storage, Energy Conversion and Biomedical Applications

Graphene, a two-dimensional (2D) layered material has attracted much attention from the scientific community due to its exceptional electrical, thermal, mechanical, biological and optical properties. Hence, numerous applications utilizing graphene-based materials could be conceived in next-generation electronics, chemical and biological sensing, energy conversion and storage, and beyond. The interaction between graphene surfaces with other materials plays a vital role in influencing its properties than other bulk materials. In this review, we outline the recent progress in the production of graphene and related 2D materials, and their uses in energy conversion (solar cells, fuel cells), energy storage (batteries, supercapacitors) and biomedical applications.

Real-time imaging of Na+ reversible intercalation in "Janus" graphene stacks for battery applications

Sodium, in contrast to other metals, cannot intercalate in graphite, hindering the use of this cheap, abundant element in rechargeable batteries. Here, we report a nanometric graphite-like anode for Na⁺ storage, formed by stacked graphene sheets functionalized only on one side, termed Janus graphene. The asymmetric functionalization allows reversible intercalation of Na⁺, as monitored by operando Raman spectroelectrochemistry and visualized by imaging ellipsometry. Our Janus graphene has uniform pore size, controllable functionalization density, and few edges; it can store Na⁺ differently from graphite and stacked graphene. Density functional theory calculations demonstrate that Na⁺ preferably rests close to -NH₂ group forming synergic ionic bonds to graphene, making the interaction process energetically favorable. The estimated sodium storage up to C_6.9Na is comparable to graphite for standard lithium ion batteries. Given such encouraging Na⁺ reversible intercalation behavior, our approach provides a way to design carbon-based materials for sodium ion batteries.

Fabrication Strategies of Twisted Bilayer Graphenes and Their Unique Properties

Twisted bilayer graphene (tBLG) exhibits a host of innovative physical phenomena owing to the formation of moiré superlattice. Especially, the discovery of superconducting behavior has generated new interest in graphene. The growing studies of tBLG mainly focus on its physical properties, while the fabrication of high-quality tBLG is a prerequisite for achieving the desired properties due to the great dependence on the twist angle and the interfacial contact. Here, the cutting-edge preparation strategies and challenges of tBLG fabrication are reviewed. The advantages and disadvantages of chemical vapor deposition, epitaxial growth on silicon carbide, stacking monolayer graphene, and folding monolayer graphene methods for the fabrication of tBLG are analyzed in detail, providing a reference for further development of preparation methods. Moreover, the characterization methods of twist angle for the tBLG are presented. Then, the unique physicochemical properties and corresponding applications of tBLG, containing correlated insulating and superconducting states, ferromagnetic state, soliton, enhanced optical absorption, tunable bandgap, and lithium intercalation and diffusion, are described. Finally, the opportunities and challenges for fabricating high-quality and large-area tBLG are discussed, unique physical properties are displayed, and new applications inferred from its angle-dependent features are explored, thereby impelling the commercialization of tBLG from laboratory to market.

Advances in the Applications of Graphene-Based Nanocomposites in Clean Energy Materials

Extensive use of fossil fuels can lead to energy depletion and serious environmental pollution. Therefore, it is necessary to solve these problems by developing clean energy. Graphene materials own the advantages of high electrocatalytic activity, high conductivity, excellent mechanical strength, strong flexibility, large specific surface area and light weight, thus giving the potential to store electric charge, ions or hydrogen. Graphene-based nanocomposites have become new research hotspots in the field of energy storage and conversion, such as in fuel cells, lithium-ion batteries, solar cells and thermoelectric conversion. Graphene as a catalyst carrier of hydrogen fuel cells has been further modified to obtain higher and more uniform metal dispersion, hence improving the electrocatalyst activity. Moreover, it can complement the network of electroactive materials to buffer the change of electrode volume and prevent the breakage and aggregation of electrode materials, and graphene oxide is also used as a cheap and sustainable proton exchange membrane. In lithium-ion batteries, substituting heteroatoms for carbon atoms in graphene composite electrodes can produce defects on the graphitized surface which have a good reversible specific capacity and increased energy and power densities. In solar cells, the performance of the interface and junction is enhanced by using a few layers of graphene-based composites and more electron-hole pairs are collected; therefore, the conversion efficiency is increased. Graphene has a high Seebeck coefficient, and therefore, it is a potential thermoelectric material. In this paper, we review the latest progress in the synthesis, characterization, evaluation and properties of graphene-based composites and their practical applications in fuel cells, lithium-ion batteries, solar cells and thermoelectric conversion.

Printable Free-Standing Hybrid Graphene/Dry-Spun Carbon Nanotube Films as Multifunctional Electrodes for Highly Stable Perovskite Solar Cells

Perovskite solar cells (PSCs) have attracted immense attention owing to their outstanding power conversion efficiency (PCE). However, their counter electrodes are commonly produced by evaporating metals, such as Ag and Au, under high vacuum conditions, which make the PSCs costly, thereby limiting their large-scale production. In this study, a free-standing hybrid graphene/carbon nanotube film was carefully designed to replace noble metal PSC counter electrodes to reduce the cost and increase the stability of PSCs. A highly conductive and stable hybrid carbon thin film can be easily transferred to the various desired substrates by a simple rolling process. The PSCs with hybrid graphene/carbon nanotube films showed a high PCE of 15.36%. Moreover, the devices exhibited excellent stability and could retain 86% of their initial PCE after storage for 500 h in a high-moisture atmosphere (RH 50%). The outstanding stability of PCEs can be attributed to the efficient moisture blocking by the multilayered graphene/carbon nanotube present in the hybrid film. The thin, flexible, and easy-to-synthesize free-standing hybrid graphene/CNT film with high conductivity showed great potential for realizing the low-cost production of highly stable PSCs.

Solution-processed, semitransparent organic photovoltaics integrated with solution-doped graphene electrodes

In this work, by applying a transfer method simultaneously with a solution doping process for graphene as top electrodes, we demonstrate a solution-processed semitransparent organic photovoltaics (OPV). The work function of doped graphene under various doping conditions was investigated via photoemission spectroscopy. The transparent device was fabricated using PEDOT-doped graphene as electrodes, which provide an energetically favorable band alignment for carrier extractions. The solution-processed semitransparent organic photovoltaics exhibit the power conversion efficiency (PCE) of 4.2%, which is 85.7% of the PCE of control devices based on metallic reflecting electrodes, while maintaining good transparency at most visible wavelengths.

Strain-Induced Band Modulation, Work Function, and QTAIM Analysis of Surface O-Functionalized Ti2C MXene

Functionalized MXenes have wide applications in the fields of gas sensors, thermoelectric materials, and hydrogen storage. Strain-induced band engineering and the work function (WF) of Ti2CO2 MXene are investigated theoretically. The calculations reveal that Ti2CO2 MXenes are stable because of the negative E coh, and all the strains considered are within the elastic limit. For Ti2CO2 MXene, strain-induced blue shift of the Ti d state results in the transformation from a semiconductor to a metal. At about 4%, Ti2CO2 MXene transforms from an indirect band gap to a direct band gap. The decreased WF induced by the strain improves the power efficiency of Ti2CO2 MXene.

Sheet Resistance Analysis of Interface-Engineered Multilayer Graphene: Mobility Versus Sheet Carrier Concentration

Both interlayer-undoped and interlayer-doped multilayer graphenes were prepared by the multiple transfers of graphene layers with multiple Cu etching (either dopant-free or doped during etching) and transfer, and the effect of interface properties on the electrical properties of multilayer graphene was investigated by varying the number of layers from 1 to 12. In both the cases, the sheet resistance decreased with increasing number of layers from 700 to 104 Ω/sq for the interlayer-undoped graphene and from 280 to 25 Ω/sq for the interlayer-doped graphene. Further, Hall measurements revealed that the origins of the sheet resistance reduction in the two cases are different. In the interlayer-undoped graphene, the sheet resistance decreased because of the increase in mobility with the addition of inner layers, which has a low carrier density and a high carrier mobility. On the other hand, it decreased because of the increase in sheet carrier density in the interlayer-doped multilayer graphene. The mobility and carrier density variations in both the cases were confirmed by fitting with the model of Hall effect in the heterojunction. In addition, we found that surface property modification by the doping of the top layer and the formation of double-layer graphene with different partial coverages allow the separate control of carrier density and mobility. Our study provides an effective approach for controlling the properties of multilayer graphene for electronic applications.

Towards large-scale graphene transfer

The transfer process is crucial for obtaining high-quality graphene for its large-scale industrial application. In this review, graphene transfer methods are systematically classified along with an analysis of the contamination or impurity of graphene that is introduced during the transfer process. Two key processes are emphasized, the substrate removal process and the direct/indirect transfer of graphene. Based on the efficiency and cost factors of industrial scale production, various transfer methods are summarized and evaluated. Potential transfer technologies and future research directions for industrial application are prospected.

Single-step fabrication and work function engineering of Langmuir-Blodgett assembled few-layer graphene films with Li and Au salts

To implement large-area solution-processed graphene films in low-cost transparent conductor applications, it is necessary to have the control over the work function (WF) of the film. In this study we demonstrate a straightforward single-step chemical approach for modulating the work function of graphene films. In our approach, chemical doping of the film is introduced at the moment of its formation. The films are self-assembled from liquid-phase exfoliated few-layer graphene sheet dispersions by Langmuir-Blodgett technique at the water-air interfaces. To achieve a single-step chemical doping, metal standard solutions are introduced instead of water. Li standard solutions (LiCl, LiNO3, Li2CO3) were used as n-dopant, and gold standard solution, H(AuCl4), as p-dopant. Li based salts decrease the work function, while Au based salts increase the work function of the entire film. The maximal doping in both directions yields a significant range of around 0.7 eV for the work function modulation. In all cases when Li-based salts are introduced, electrical properties of the film deteriorate. Further, lithium nitrate (LiNO3) was selected as the best choice for n-type doping since it provides the largest work function modulation (by 400 meV), and the least influence on the electrical properties of the film.

Variable-Temperature Electron Transport and Dipole Polarization Turning Flexible Multifunctional Microsensor beyond Electrical and Optical Energy

Humans are undergoing a fateful transformation focusing on artificial intelligence, quantum information technology, virtual reality, etc., which is inseparable from intelligent nano-micro devices. However, the booming of "Big Data" brings about an even greater challenge by growing electromagnetic radiation. Herein, an innovative flexible multifunctional microsensor is proposed, opening up a new horizon for intelligent devices. It integrates "non-crosstalk" multiple perception and green electromagnetic interference shielding only in one pixel, with satisfactory sensitivity and fast information feedback. Importantly, beneficial by deep insight into the variable-temperature electromagnetic response, the microsensor tactfully transforms the urgent threat of electromagnetic radiation into "wealth," further integrating self-power. This result will refresh researchers' realization of next-generation devices, ushering in a new direction for aerospace engineering, remote sensing, communications, medical treatment, biomimetic robot, prosthetics, etc.

Advances in the application, toxicity and degradation of carbon nanomaterials in environment: A review

Carbon nanomaterials (CNMs) are novel nanomaterials with excellent physicochemical properties, which are widely used in biomedicine, energy and sensing. Besides, CNMs also play an important role in environmental pollution control, which can absorb heavy metals, antibiotics and harmful gases. However, CNMs are inevitably entering the environment while they are rapidly developing. They are harmful to living organisms in the environment and are difficult to degrade under natural conditions. Here, we systematically describe the toxicity of carbon nanotubes (CNTs), graphene (GRA) and C₆₀ to cells, animals, humans, and microorganisms. According to the current research results, the toxicity mechanism is summarized, including oxidative stress response, mechanical damage and effects on biological enzymes. In addition, according to the latest research progress, we focus on the two major degradation methods of chemical degradation and biodegradation of CNTs, GRA and C₆₀. Meanwhile, the reaction conditions and degradation mechanisms of degradation are respectively stated. Moreover, we have prospects for the limitations of CNM degradation under non-experimental conditions and their potential application.

Multilayer Graphene-Based Thermal Rectifier with Interlayer Gradient Functionalization

As a counterpart of electrical and optical diodes with asymmetric transmission properties, the nanoscale thermal rectifier has attracted huge attention. Graphene has been expected as the most promising candidate for the design and fabrication of high-performance thermal rectifiers. However, most reported graphene-based thermal rectification has been achieved only within the plane of the graphene layer, and the efficiency is heavily limited by the lateral size, restricting the potential applications. In this paper, we propose a design of multilayer graphene-based thermal rectifier (MGTR) with interlayer gradient functionalization. A unique thermal rectification along the vertical direction without lateral size limitation is demonstrated by molecular dynamics simulations. The heat flux prefers to transport from a fully hydrogenated graphene layer to a pristine graphene layer. The analysis of phonon density of states reveals that the mismatch between dominant frequency domains plays a crucial role in the vertical thermal rectification phenomenon. The impacts of temperature and strain on the rectification efficiency are systematically investigated, and we verify the interlayer welding process as an effective approach to eliminate the degradation induced by out-of-plane compression. In addition, compared with uniform hydrogenation at average H-coverage, an anomalous enhancement of in-plane thermal conductivity of multilayer graphene with interlayer gradient hydrogenation is observed. The proposed MGTR has great potential in designing devices for heat management and logic control.

Defect-assisted protein HP35 denaturation on graphene

Structural defects in nanomaterials can alter their physical and chemical properties including magnetization, electronic and thermal conductivities, light absorption, and emission capabilities. Here, we investigated the potential impact of these defects on their biological effects through molecular dynamics simulations. By modeling the interaction between a graphene nanosheet and a widely used model protein, the chicken villin headpiece subdomain (HP35), we observed severe protein denaturation upon contact with defective graphene, while the protein remained intact on ideal graphene. The enhanced toxicity of defective graphene was due to the stronger attraction of the surface residues of HP35 from the defect edges (represented by carboxyl groups in our simulations) than from the ideal graphene. Upon binding to defective graphene, the contacting residues were restrained near the defective sites, which acted as "anchors" for the adsorbed protein. The "anchors" subsequently caused the protein to expose its aromatic and hydrophobic core residues to the graphene surface, via strong π-π stacking and hydrophobic interactions, thus leading to the unfolding of the protein. These findings not only highlight the importance of defects in nanomaterials' impact on biological systems, but also provide insights into fine-tuning the potential biological properties of nanomaterials through defect engineering.

Impact of Graphene Work Function on the Electronic Structures at the Interface between Graphene and Organic Molecules

The impact of graphene work function (WF) on the electronic structure at the graphene/organic interface has been investigated. WF manipulation of graphene is realized using self-assembled monolayers (SAMs) with different end groups. With this method, the upper surface of the functionalized graphene remains intact, and thus precludes changes of molecular orientation and packing structures of subsequently deposited active materials. The WF of NH₂-SAM functionalized graphene is ~3.90 eV. On the other hand, the WF of graphene increases to ~5.38 eV on F-SAM. By tuning the WF of graphene, an upward band bending is found at the ZnPc/graphene interface on F-SAM. At the interface between C₆₀ and NH₂-SAM modified graphene, a downward band bending is observed.

Intercalation of Layered Materials from Bulk to 2D

Intercalation in few-layer (2D) materials is a rapidly growing area of research to develop next-generation energy-storage and optoelectronic devices, including batteries, sensors, transistors, and electrically tunable displays. Identifying fundamental differences between intercalation in bulk and 2D materials will play a key role in developing functional devices. Herein, advances in few-layer intercalation are addressed in the historical context of bulk intercalation. First, synthesis methods and structural properties are discussed, emphasizing electrochemical techniques, the mechanism of intercalation, and the formation of a solid-electrolyte interphase. To address fundamental differences between bulk and 2D materials, scaling relationships describe how intercalation kinetics, structure, and electronic and optical properties depend on material thickness and lateral dimension. Here, diffusion rates, pseudocapacity, limits of staging, and electronic structure are compared for bulk and 2D materials. Next, the optoelectronic properties are summarized, focusing on charge transfer, conductivity, and electronic structure. For energy devices, opportunities also emerge to design van der Waals heterostructures with high capacities and excellent cycling performance. Initial studies of heterostructured electrodes are compared to state-of-the-art battery materials. Finally, challenges and opportunities are presented for 2D materials in energy and optoelectronic applications, along with promising research directions in synthesis and characterization to engineer 2D materials for superior devices.

A Double Support Layer for Facile Clean Transfer of Two-Dimensional Materials for High-Performance Electronic and Optoelectronic Devices

Clean transfer of two-dimensional (2D) materials grown by chemical vapor deposition is critical for their application in electronics and optoelectronics. Although rosin can be used as a support layer for the clean transfer of graphene grown on Cu, it has not been usable for the transfer of 2D materials grown on noble metals or for large-area transfer. Here, we report a poly(methyl methacrylate) (PMMA)/rosin double support layer that enables facile ultraclean transfer of large-area 2D materials grown on different metals. The bottom rosin layer ensures clean transfer, whereas the top PMMA layer not only screens the rosin from the transfer conditions but also improves the strength of the transfer layer to make the transfer easier and more robust. We demonstrate the transfer of monolayer WSe₂ and WS₂ single crystals grown on Au as well as large-area graphene films grown on Cu. As a result of the clean surface, the transferred WSe₂ retains the intrinsic optical properties of the as-grown sample. Moreover, it does not require annealing to form good ohmic contacts with metal electrodes, enabling high-performance field effect transistors with mobility and ON/OFF ratio ∼10 times higher than those made by PMMA-transferred WSe₂. The ultraclean graphene film is found to be a good anode for flexible organic photovoltaic cells with a high power conversion efficiency of ∼6.4% achieved.

A Universal Stamping Method of Graphene Transfer for Conducting Flexible and Transparent Polymers

Transfer method of chemically vapor deposition graphene is an appealing issue to realize its application as flexible and transparent electrodes. A universal stamping method to transfer as grown graphene from copper onto different flexible and transparent polymers (FTPs) reported here ensures simple, robust, rapid, clean and low-cost. This method relies on coating ethylene vinyl acetate (EVA) onto the as grown graphene, binding EVA coated graphene/Cu with FTPs and delamination by hydrogen bubbling process, which is analogous to the method used by stamping process where ink carries the imprint of the object onto any materials. The fate of the stamping method depends on how strongly the adhesion of EVA coated graphene/Cu with target FTPs. Interestingly, we have found that the thin film of EVA/graphene/Cu can only bind strongly with the FTPs of less than 25 µm in thickness and lower glass transition temperature value to the EVA while wide range of other FTPs are considered upon surface engineering to enhance the binding strength between FTPs and EVA. What’s more, the electrical performance was investigated with a demonstration of triboelectric nanogenerators which confirmed the reliability of graphene transfer onto the FTPs and prospect for the development of flexible and transparent electronics.

Bio-interfactants as double-sided tapes for graphene oxide

We present a versatile and highly substrate-independent approach for preparing multisandwich layers based on thermally reduced Graphene Oxide (rGO) which gets strongly attached by bio-interfactants using a layer-by-layer (LBL) aqueous dipping and rinsing process. The process allows for the deposition of homogeneous ultra-thin films (∼5.5 nm) in distinct surface topographies, thicknesses and compositions by varying the bio-interfactant layer(s). The layers formed on quartz or other semi conductive material are electrically conductive, flexible, and transparent. The here-developed approach could be applied for the fabrication of wearables, sensors, and antistatic transparent films.

Carbon-Based Photocathode Materials for Solar Hydrogen Production

Hydrogen is considered a promising environmentally friendly energy carrier for replacing traditional fossil fuels. In this context, photoelectrochemical cells effectively convert solar energy directly to H₂ fuel by water photoelectrolysis, thereby monolitically combining the functions of both light harvesting and electrolysis. In such devices, photocathodes and photoanodes carry out the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER), respectively. Here, the focus is on photocathodes for HER, traditionally based on metal oxides, III-V group and II-VI group semiconductors, silicon, and copper-based chalcogenides as photoactive material. Recently, carbon-based materials have emerged as reliable alternatives to the aforementioned materials. A perspective on carbon-based photocathodes is provided here, critically analyzing recent research progress and outlining the major guidelines for the development of efficient and stable photocathode architectures. In particular, the functional role of charge-selective and protective layers, which enhance both the efficiency and the durability of the photocathodes, is discussed. An in-depth evaluation of the state-of-the-art fabrication of photocathodes through scalable, high-troughput, cost-effective methods is presented. The major aspects on the development of light-trapping nanostructured architectures are also addressed. Finally, the key challenges on future research directions in terms of potential performance and manufacturability of photocathodes are analyzed.

The Role of Graphene and Other 2D Materials in Solar Photovoltaics

2D materials have attracted considerable attention due to their exciting optical and electronic properties, and demonstrate immense potential for next-generation solar cells and other optoelectronic devices. With the scaling trends in photovoltaics moving toward thinner active materials, the atomically thin bodies and high flexibility of 2D materials make them the obvious choice for integration with future-generation photovoltaic technology. Not only can graphene, with its high transparency and conductivity, be used as the electrodes in solar cells, but also its ambipolar electrical transport enables it to serve as both the anode and the cathode. 2D materials beyond graphene, such as transition-metal dichalcogenides, are direct-bandgap semiconductors at the monolayer level, and they can be used as the active layer in ultrathin flexible solar cells. However, since no 2D material has been featured in the roadmap of standard photovoltaic technologies, a proper synergy is still lacking between the recently growing 2D community and the conventional solar community. A comprehensive review on the current state-of-the-art of 2D-materials-based solar photovoltaics is presented here so that the recent advances of 2D materials for solar cells can be employed for formulating the future roadmap of various photovoltaic technologies.

Graphene/Si Schottky solar cells: a review of recent advances and prospects

Graphene has attracted tremendous interest due to its unique physical and chemical properties. The atomic thickness, high carrier mobility and transparency make graphene an ideal electrode material which can be applied to various optoelectronic devices such as solar cells, light-emitting diodes and photodetectors. In recent years, there has been a growing interest in developing graphene/silicon Schottky junction solar cells and the power conversion efficiency has reached up to 15.8% with an incredible speed. In this review, we introduce the structure and mechanism of graphene/silicon solar cells briefly, and then summarize several key strategies to improve the performance of the cells. Finally, the challenges and prospects of graphene/silicon solar cells are discussed in the development of the devices in detail.

The structure and mechanism of graphene/silicon solar cells, and several key strategies to improve the performance of the cells.

Transparent Conductive Electrodes Based on Graphene-Related Materials

Transparent conducting electrodes (TCEs) are the most important key component in photovoltaic and display technology. In particular, graphene has been considered as a viable substitute for indium tin oxide (ITO) due to its optical transparency, excellent electrical conductivity, and chemical stability. The outstanding mechanical strength of graphene also provides an opportunity to apply it as a flexible electrode in wearable electronic devices. At the early stage of the development, TCE films that were produced only with graphene or graphene oxide (GO) were mainly reported. However, since then, the hybrid structure of graphene or GO mixed with other TCE materials has been investigated to further improve TCE performance by complementing the shortcomings of each material. This review provides a summary of the fabrication technology and the performance of various TCE films prepared with graphene-related materials, including graphene that is grown by chemical vapor deposition (CVD) and GO or reduced GO (rGO) dispersed solution and their composite with other TCE materials, such as carbon nanotubes, metal nanowires, and other conductive organic/inorganic material. Finally, several representative applications of the graphene-based TCE films are introduced, including solar cells, organic light-emitting diodes (OLEDs), and electrochromic devices.

Controlling graphene work function by doping in a MOCVD reactor

Here we demonstrate a new method for doping graphene using Metal Organic Chemical Vapor Deposition (MOCVD) reactor. The original undoped graphene was of a very high quality mounted on Si/SiO₂ substrates, they were then doped in the MOCVD's reactor using tertiarybutylphosphine (TBP) and tertiarybutylarsene (TBA). Post process Raman spectroscopy confirmed the presence of a single layer of phosphor doped graphene (G/P) and Arsine doped graphene (G/As) when doped by TBP or by TBA, respectively. Blue shift of the 2D peak assured p-type doping. The work function determined by ultraviolet photoelectron spectroscopy varied from 4.5 eV for Pristine Graphene to 4.7, 4.8 eV for G/As, G/P, respectively. The increase of the work function is attributed to electron transfer from the graphene to the dopant. Our results suggest that doping graphene by MOCVD with TBA or TBP can easily and effectively alternate the work function by few tenths of eV and improve the electronic properties of graphene. The MOCVD technology of doping graphene opens a new route on which other semiconductors can be epitaxially grown on it in a continues process in the same MOCVD reactor.