Atomically Thin Mesoporous Co3 O4 Layers Strongly Coupled with N-rGO Nanosheets as High-Performance Bifunctional Catalysts for 1D Knittable Zinc-Air Batteries

Cobalt-Doped MnFe2O4 Spinel Coupled with Nitrogen-Doped Reduced Graphene Oxide: Enhanced Oxygen Electrocatalytic Activity for Zinc-Air Batteries

MFCO spinel anchored on N-rGO is synthesized by a two-step hydrothermal method as a bifunctional electrocatalyst. Its physicochemical properties have been characterized and tested, and it is applied to zinc-air batteries. The experimental and theoretical calculations show that the MFCO is uniformly distributed on the surface of N-rGO. When MFCO is anchored on the conducting N-rGO, a synergistic effect occurs between the Co-N bonds, which changes the arrangement of the C-N bonds from the sp2 orientation to the sp3 form. The ORR catalytic pathway of the MFCO/N-rGO electrocatalyst is dominated by 4-electron transfer, with a half-wave potential of 0.8003 V, an overpotential value of 352 mV, and a small potential difference (ΔE = 0.78 V). With a charge/discharge voltage difference of about 0.88 V, the voltage gap remains almost unchanged for a long period after 650 h, showing excellent stability. The improved catalytic performance is attributed to Co acting as an active site, and the doping of Co induces the Jahn-Teller effect, which alters the electronic structure of spinel, shifts the d-band center upward, enhances the adsorption of oxygen intermediates, and promotes the oxygen electrocatalytic reaction. This study provides a low-cost and promising bifunctional oxygen electrocatalyst for zinc-air batteries.

Spiny Co3O4@Hollow Carbon Spheres─Polyacrylonitrile/Carbon Black Fiber-Based Bifunctional Air Electrodes

In the realm of zinc-air batteries, high bifunctional catalytic efficacy is intimately tied to the evaluation of catalysts. Consequently, the pursuit of proficient bifunctional catalysts that can efficiently catalyze both the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) remains a paramount objective in this research area. In this study, the spiny cobalt tetroxide (Co3O4) encapsulated hollow carbon spheres (HCSs) are constructed by anchoring Co3O4 onto HCS via hydrothermal or annealing treatment. The strategic interface design of the HCS encourages an abundance of sites while simultaneously facilitating the proliferation of spiny Co3O4, offering an expansive surface area and abundant active sites. The surface active Co3+ ions and the induction of surface oxygen vacancies in spiny Co3O4 encapsulated HCS endow it with outstanding bifunctional catalytic activity and stability. After spray-coating and subsequent annealing of the spiny Co3O4 encapsulated HCS catalyst on the flexible carbon-based polyacrylonitrile (PAN) nanofiber support, the spiny Co3O4 encapsulated HCS-PAN/carbon black (C) 800 air electrode is successfully integrated. Moreover, the optimized spiny Co3O4 encapsulated HCS-PAN/C 800 air electrode displays a decreased potential difference (ΔE) of 0.77 V for catalyzing the ORR and OER performance. This work introduces a promising candidate approach for exploring innovative bifunctional oxygen electrocatalysts, targeting enhanced efficiency in portable energy storage applications.

Cucurbit[n]uril-Derived Electrocatalysts for Oxygen Evolution, Oxygen Reduction, and Hydrogen Evolution Reactions

Various sustainable energy conversion techniques like water electrolyzers, fuel cells, and metal-air battery devices are promising to alleviate the issues in fossil fuel consumption. However, their broad employment has been mainly inhibited by the lack of advanced electrocatalysts to accelerate the sluggish kinetics of the three involved half-reactions including oxygen evolution reaction (OER), oxygen reduction reaction (ORR), and hydrogen evolution reaction (HER). Recent advances have witnessed the cucurbit[n]uril (CB[n])-directed strategy as a prominent tool to develop high performance electrocatalysts with either OER, ORR, or HER activities. In this review, the recent progress on CB[n]-derived electrocatalysts ranging from molecular complexes to heterogeneous nanostructures and single-atoms for the three half-reactions are reviewed, and future opportunities are discussed. A concise introduction to the fundamentals of CB[n]s regarding their synthesis, structure, and chemistry is given first. Subsequently, the systematic summary of CB[n]-derived electrocatalysts and their performance for the OER/ORR/HER are discussed in detail, with a specific emphasis on correlating their structure and activities by combining diverse physiochemical characterizations, electrochemical experiments, and theory simulations. Finally, a brief conclusion and perspective for future opportunities regarding CB[n]-derived electrocatalysts for many other electrocatalytic applications are proposed.

Hydrogel Electrolyte-Mediated In Situ Zn-Anode Modification and the Ru-RuO2/NGr-Coated Cathode for High-Performance Solid-State Rechargeable Zn-Air Batteries

This work aims to deal with the challenges associated with designing complementary bifunctional electrocatalysts and a separator/membrane that enables rechargeable zinc-air batteries (RZABs) with nearly solid-state operability. This solid-state RZAB was accomplished by integrating a bifunctional electrocatalyst based on Ru-RuO2 interface nanoparticles supported on nitrogen-doped (N-doped) graphene (Ru-RuO2/NGr) and a dual-doped poly(acrylic acid) hydrogel (d-PAA) electrolyte soaked in KOH with sodium stannate additive. The catalyst shows enhanced activity and stability toward the two oxygen reactions, i.e., oxygen reduction and evolution reactions (ORR and OER), with a very low potential difference (ΔE) of 0.64 V. The computational insights bring out the electronic factors contributing to the enhanced catalytic activity of Ru-RuO2/NGr based on the charge density difference (CDD) between the interfaces. The disadvantages of the existing solid-state RZABs, such as their limited lifespan brought on by passivation, dendritic growth, corrosion, and shape change, have also been taken into account. The introduction of the stannate additive to the electrolyte induced an in situ Zn-anode modification, which subsequently improved the interfacial stability of the ZABs and, hence, the battery life cycles. The experimental observations reveal that, during the charging process, the Sn nanoparticles enable the homogeneous Zn deposition on the surface of the anode. Thus, the in situ Zn-anode surface modification assisted in achieving a high-rate cycle capability, viz., the homemade catalyst-based system exhibited continuous charge-discharge cycles for 20 h at a current density of 2.0 mA cm-2, with each cycle lasting for 5 min.

All-in-One Polymer Gel Electrolyte towards High-Efficiency and Stable Fiber Zinc-Air Battery

Fiber zinc-air batteries are explored as promising power systems for wearable and portable electronic devices due to their intrinsic safety and the use of ambient oxygen as cathode material. However, challenges such as limited zinc anode reversibility and sluggish cathode reaction kinetics result in poor cycling stability and low energy efficiency. To address these challenges, we design a polydopamine-based all-in-one gel electrolyte (PAGE) that simultaneously regulates the reversibility of zinc anodes and the kinetics of air cathodes through polydopamine interfacial and redox chemistry, respectively. The intrinsic catechol and carboxylate groups in PAGE regulate the transport and solvation structure of Zn2+, facilitating dendrite-free zinc deposition with a lamellar stacking morphology. Additionally, the oxidation of redox-active catechol groups in PAGE replaces the sluggish oxygen evolution reaction on the air cathode and reduces the energy barrier for charging, enabling fiber zinc-air batteries to achieve a significantly improved energy efficiency of 95 % and a longer lifespan of 40 hours. Further integration into self-powered electronic textiles underscores its potential for next-generation wearable systems.

Composite Gel Polymer Electrolyte for High-Performance Flexible Zinc-Air Batteries

Enhancing ionic conductivity and electrolyte uptake is of significance for gel polymer electrolytes (GPEs) for flexible zinc-air batteries (FZABs). Herein, a composite mesoporous silica/polyacrylamide (5 wt.% mPAM) GPE is constructed with comparable ionic conductivity to aqueous electrolytes, where the ionic conductivity is up to 337 mS cm-1, and the weight loss after exposing in air 72 h is less than 18%, owing to the excellent electrolyte uptake and continuous ion migration network provided by the mesoporous silica fillers. When used as a quasi-solid-electrolyte, the rechargeable FZAB exhibited high electrochemical performance and structural stability, where the peak power density is up to 162.8 mW cm-2, and the initial charge-discharge potential gap is as low as 0.62 V, resulting in a long lifespan exceeding 110 h, showcasing the combination of high durability, cost-effectiveness and easy production for practical applications.

Second-Shell Coordination Environment Modulation for MnN4 Active Sites by Oxygen Doping to Boost Oxygen Reduction Performance

As a category of transition metal-nitrogen-carbon (M-N-C) catalysts, Mn-based single-atom catalysts (SACs) are considered as promising non-precious metal catalysts for stable oxygen reduction reaction (ORR) due to their Fenton-inactive character (versus Fe) and more abundant earth reserves (versus Ni, Co). However, their ORR activity is unsatisfactory. Besides, the structure-activity relationship via tuning the coordination environment of the second coordination shell for transition metal single sites is still elusive. Here, a Mn SAC with O doping in the second-shell of atomically dispersed Mn centers (MnSAC-O/C) as highly efficient and stable ORR catalyst is developed. X-ray absorption spectroscopy combined with theoretical calculations verifies the O doping in the second-shell of Mn center, and reveals the distortion of local environment of Mn center in the MnSAC-O/C. The MnSAC-O/C exhibits high ORR performance with a half-wave potential of 0.898 V, superior to MnSAC-C, commercial Pt/C and most reported non-noble metal-based SACs. More importantly, MnSAC-O/C based zinc-air batteries (ZABs) deliver outstanding durability with stable operation exceeding 930 h. Theoretical calculations confirm that O doping breaks the symmetry of charge distribution of MnN4 active center and facilitates OH* desorption, thus attributing to the promoted ORR activity.

Bacterial Cellulose Applications in Electrochemical Energy Storage Devices

Bacterial cellulose (BC) is produced via the fermentation of various microorganisms. It has an interconnected 3D porous network structure, strong water-locking ability, high mechanical strength, chemical stability, anti-shrinkage properties, renewability, biodegradability, and a low cost. BC-based materials and their derivatives have been utilized to fabricate advanced functional materials for electrochemical energy storage devices and flexible electronics. This review summarizes recent progress in the development of BC-related functional materials for electrochemical energy storage devices. The origin, components, and microstructure of BC are discussed, followed by the advantages of using BC in energy storage applications. Then, BC-related material design strategies in terms of solid electrolytes, binders, and separators, as well as BC-derived carbon nanofibers for electroactive materials are discussed. Finally, a short conclusion and outlook regarding current challenges and future research opportunities related to BC-based advanced functional materials for next-generation energy storage devices suggestions are proposed.

Design of Atomically Dispersed CoN4 Sites and Co Clusters for Synergistically Enhanced Oxygen Reduction Electrocatalysis

Constructing dual-site catalysts consisting of atomically dispersed metal single atoms and metal atomic clusters (MACs) is a promising approach to further boost the catalytic activity for oxygen reduction reaction (ORR). Herein, a porous CoSA-AC@SNC featuring the coexistence of Co single-atom sites (CoN4) and S-coordinated Co atomic clusters (SCo6) in S, N co-doped carbon substrate is successfully synthesized by using porphyrinic metal-organic framework (Co-TPyP MOF) as the precursor. The introduction of the sulfur source creates abundant microstructural defects to anchor Co metal clusters, thus modulating the electronic structure of its surrounding carbon substrate. The synergistic effect between the two types of active sites and structural advantages, in turn, results in high ORR performance of CoSA-AC@SNC with half-wave potential (E1/2) of 0.86 V and Tafel slope of 50.17 mV dec-1. Density functional theory (DFT) calculations also support the synergistic effect between CoN4 and SCo6 by detailing the catalytic mechanism for the improved ORR performance. The as-fabricated Zn-air battery (ZAB) using CoSA-AC@SNC demonstrates impressive peak power density of 174.1 mW cm-2 and charge/discharge durability for 148 h. This work provides a facile synthesis route for dual-site catalysts and can be extended to the development of other efficient atomically dispersed metal-based electrocatalysts.

Single-Anion Conductive Solid-State Electrolytes with Hierarchical Ionic Highways for Flexible Zinc-Air Battery

Flexible zinc-air batteries are leading power sources for next-generation smart wearable electronics. However, flexible zinc-air batteries suffer from the highly-corrosive safety risk and limited lifespan due to the absence of reliable solid-state electrolytes (SSEs). Herein, a single-anion conductive SSE with high-safety is constructed by incorporating a highly amorphous dual-cation ionomer into a robust hybrid matrix of functional carbon nanotubes and polyacrylamide polymer. The as-fabricated SSE obtains dual-penetrating ionomer-polymer networks and hierarchical ionic highways, which contribute to mechanical robustness with 1200 % stretchability, decent water uptake and retention, and superhigh ion conductivity of 245 mS ⋅ cm-1 and good Zn anode reversibility. Remarkably, the flexible solid-state zinc-air batteries delivers a high specific capacity of 764 mAh ⋅ g-1 and peak power density of 152 mW ⋅ cm-2 as well as sustains excellent cycling stability for 1050 cycles (350 hours). This work offers a new paradigm of OH- conductors and broadens the definition and scope of OH- conductors.

NiCo2O4 Nanowires Immobilized on Nitrogen-Doped Ti3C2Tx for High-Performance Wearable Magnesium-Air Batteries

Flexible magnesium (Mg)-air batteries provide an ideal platform for developing efficient energy-storage devices toward wearable electronics and bio-integrated power sources. However, high-capacity bio-adaptable Mg-air batteries still face the challenges in low discharge potential and inefficient oxygen electrodes, with poor kinetics property toward oxygen reduction reaction (ORR). Herein, spinel nickel cobalt oxides (NiCo2O4) nanowires immobilized on nitrogen-doped Ti3C2Tx (NiCo2O4/N-Ti3C2Tx) are reported via surface chemical-bonded effect as oxygen electrodes, wherein surface-doped pyridinic-N-C and Co-pyridinic-N moieties accounted for efficient ORR owing to increased interlayer spacing and changed surrounding environment around Co metals in NiCo2O4. Importantly, in polyethylene glycol (PVA)-NaCl neutral gel electrolytes, the NiCo2O4/N-Ti3C2Tx-assembled quasi-solid wearable Mg-air batteries delivered high open-circuit potential of 1.5 V, good flexibility under various bent angles, high power density of 9.8 mW cm-2, and stable discharge duration to 12 h without obvious voltage drop at 5 mA cm-2, which can power a blue flexible light-emitting diode (LED) array and red smart rollable wearable device. The present study stimulates studies to investigate Mg-air batteries involving human-body adaptable neutral electrolytes, which will facilitate the application of Mg-air batteries in portable, flexible, and wearable power sources for electronic devices.

Recent Advances in Catalyst Design and Performance Optimization of Nanostructured Cathode Materials in Zinc-Air Batteries

This review focuses on the advanced design and optimization of nanostructured zinc-air batteries (ZABs), with the aim of boosting their energy storage and conversion capabilities. The findings show that ZABs favor porous nanostructures owing to their large surface area, and this enhances the battery capacity, catalytic activity, and life cycle. In addition, the nanomaterials improve the electrical conductivity, ion transport, and overall battery stability, which crucially reduces dendrite growth on the zinc anodes and improves cycle life and energy efficiency. To obtain a superior performance, the importance of controlling the operational conditions and using custom nanostructural designs, optimal electrode materials, and carefully adjusted electrolytes is highlighted. In conclusion, porous nanostructures and nanoscale materials significantly boost the energy density, longevity, and efficiency of Zn-air batteries. It is suggested that future research should focus on the fundamental design principles of these materials to further enhance the battery performance and drive sustainable energy solutions.

Zn-based batteries for sustainable energy storage: strategies and mechanisms

Batteries play a pivotal role in various electrochemical energy storage systems, functioning as essential components to enhance energy utilization efficiency and expedite the realization of energy and environmental sustainability. Zn-based batteries have attracted increasing attention as a promising alternative to lithium-ion batteries owing to their cost effectiveness, enhanced intrinsic safety, and favorable electrochemical performance. In this context, substantial endeavors have been dedicated to crafting and advancing high-performance Zn-based batteries. However, some challenges, including limited discharging capacity, low operating voltage, low energy density, short cycle life, and complicated energy storage mechanism, need to be addressed in order to render large-scale practical applications. In this review, we comprehensively present recent advances in designing high-performance Zn-based batteries and in elucidating energy storage mechanisms. First, various redox mechanisms in Zn-based batteries are systematically summarized, including insertion-type, conversion-type, coordination-type, and catalysis-type mechanisms. Subsequently, the design strategies aiming at enhancing the electrochemical performance of Zn-based batteries are underscored, focusing on several aspects, including output voltage, capacity, energy density, and cycle life. Finally, challenges and future prospects of Zn-based batteries are discussed.

Synergistic Lewis and Brønsted Acid Sites Promote OH* Formation and Enhance Formate Selectivity: Towards High-efficiency Glycerol Valorization

As a sustainable valorization route, electrochemical glycerol oxidation reaction (GOR) involves in formation of key OH* and selective adsorption/cleavage of C-C(O) intermediates with multi-step electron transfer, thus suffering from high potential and poor formate selectivity for most non-noble-metal-based electrocatalysts. So, it remains challenging to understand the structure-property relationship as well as construct synergistic sites to realize high-activity and high-selectivity GOR. Herein, we successfully achieve dual-high performance with low potentials and superior formate selectivity for GOR by forming synergistic Lewis and Brønsted acid sites in Ni-alloyed Co-based spinel. The optimized NiCo oxide solid-acid electrocatalyst exhibits low reaction potential (1.219 V@10 mA/cm2) and high formate selectivity (94.0 %) toward GOR. In situ electrochemical impedance spectroscopy and pH-dependence measurements show that the Lewis acid centers could accelerate OH* production, while the Brønsted acid centers are proved to facilitate high-selectivity formation of formate. Theoretical calculations reveal that NiCo alloyed oxide shows appropriate d-band center, thus balancing adsorption/desorption of C-O intermediates. This study provides new insights into rationally designing solid-acid electrocatalysts for biomass electro-upcycling.

Cobalt/Nitrogen Co-Doped Carbon Materials Enhance the Reaction Rate of Sodium-Potassium Alloy Electrodes

Sodium-potassium (NaK) alloy electrodes are ideal for next-generation dendrite-free alkali metal electrodes due to their dendrite-free nature. However, issues such as slow diffusion kinetics due to the large K+ radius and the loss of active potassium during the reaction severely limit its application. Here a novel cobalt/nitrogen-doped carbon material is designed and it is applied to the construction of a NaK alloy electrode. The experimental and theoretical results indicate that the confining effect of the nitrogen-doped graphitic carbon layer can protect the cobalt nanoparticles from corrosion leaching, while the presence of Co─Nx bonds and cobalt nanoparticles provides more active sites for the reaction, realizing the synergistic effect of adsorption-catalytic modulation, lowering the K+ diffusion energy barrier and promoting charge transfer and ion diffusion. The application of this electrode to a symmetrical battery can achieve more than 1800 stable cycles under a current density of 0.4 mA cm-2 and a charge/discharge specific capacity of 122.64 mAh g-1 under a current of 0.5C in a full battery. This finding provides a new idea to realize a fast, stable, and efficient application of NaK alloy electrodes.

Nanoscale Metal Particle Modified Single-Atom Catalyst: Synthesis, Characterization, and Application

Single-atom catalysts (SACs) have attracted considerable attention in heterogeneous catalysis because of their well-defined active sites, maximum atomic utilization efficiency, and unique unsaturated coordinated structures. However, their effectiveness is limited to reactions requiring active sites containing multiple metal atoms. Furthermore, the loading amounts of single-atom sites must be restricted to prevent aggregation, which can adversely affect the catalytic performance despite the high activity of the individual atoms. The introduction of nanoscale metal particles (NMPs) into SACs (NMP-SACs) has proven to be an efficient approach for improving their catalytic performance. A comprehensive review is urgently needed to systematically introduce the synthesis, characterization, and application of NMP-SACs and the mechanisms behind their superior catalytic performance. This review first presents and classifies the different mechanisms through which NMPs enhance the performance of SACs. It then summarizes the currently reported synthetic strategies and state-of-the-art characterization techniques of NMP-SACs. Moreover, their application in electro/thermo/photocatalysis, and the reasons for their superior performance are discussed. Finally, the challenges and perspectives of NMP-SACs for the future design of advanced catalysts are addressed.

Rechargeable Zinc-Air Batteries: Advances, Challenges, and Prospects

Rechargeable zinc-air batteries (Re-ZABs) are one of the most promising next-generation batteries that can hold more energy while being cost-effective and safer than existing devices. Nevertheless, zinc dendrites, non-portability, and limited charge-discharge cycles have long been obstacles to the commercialization of Re-ZABs. Over the past 30 years, milestone breakthroughs have been made in technical indicators (safety, high energy density, and long battery life), battery components (air cathode, zinc anode, and gas diffusion layer), and battery configurations (flexibility and portability), however, a comprehensive review on advanced design strategies for Re-ZABs system from multiple angles is still lacking. This review underscores the progress and strategies proposed so far to pursuit the high-efficiency Re-ZABs system, including the aspects of rechargeability (from primary to rechargeable), air cathode (from unifunctional to bifunctional), zinc anode (from dendritic to stable), electrolytes (from aqueous to non-aqueous), battery configurations (from non-portable to portable), and industrialization progress (from laboratorial to practical). Critical appraisals of the advanced modification approaches (such as surface/interface modulation, nanoconfinement catalysis, defect electrochemistry, synergistic electrocatalysis, etc.) are highlighted for cost-effective flexible Re-ZABs with good sustainability and high energy density. Finally, insights are further rendered properly for the future research directions of advanced zinc-air batteries.

Scaling-Up Insights for Zinc-Air Battery Technologies Realizing Reversible Zinc Anodes

Zinc-air battery (ZAB) technology is considered one of the promising candidates to complement the existing lithium-ion batteries for future large-scale high-energy-storage demands. The scientific literature reveals many efforts for the ZAB chemistries, materials design, and limited accounts for cell design principles with apparently superior performances for liquid and solid-state electrolytes. However, along with the difficulty of forming robust solid-electrolyte interphases, the discrepancy in testing methods and assessment metrics severely challenges the realistic evaluation/comparison and commercialization of ZABs. Here, strategies to formulate reversible zinc anodes are proposed and specific cell-level energy metrics (100-500 Wh kg-1 ) and realistic long-cycling operations are realized. Stabilizing anode/electrolyte interfaces results in a cumulative capacity of 25 Ah cm-2 and Coulomb efficiency of >99.9% for 5000 plating/stripping cycles. Using 1-10 Ah scale (≈500 Wh kg-1 at cell level) solid-state zinc-air pouch cells, scale-up insights for Ah-level ZABs that can progress from lab-scale research to practical production are also offered.

Tailoring Oxygen Reduction Reaction Kinetics on Perovskite Oxides via Oxygen Vacancies for Low-Temperature and Knittable Zinc-Air Batteries

High kinetics oxygen reduction reaction (ORR) electrocatalysts under low temperature are critical and highly desired for temperature-tolerant energy conversion and storage devices, but remain insufficiently investigated. Herein, oxygen vacancy-rich porous perovskite oxide (CaMnO3 ) nanofibers coated with reduced graphene oxide coating (V-CMO/rGO) are developed as the air electrode catalyst for low-temperature and knittable Zn-air batteries. V-CMO/rGO exhibits top-level ORR activity among perovskite oxides and shows impressive kinetics under low temperature. Experimental and theoretical calculation results reveal that the synergistic effect between metal atoms and oxygen vacancies, as well as the accelerated kinetics and enhanced electric conductivity and mass transfer over the rGO coated nanofiber 3D network contribute to the enhanced catalytic activity. The desorption of ORR intermediate is promoted by the regulated electron filling. The V-CMO/rGO drives knittable and flexible Zn-air batteries under a low temperature of -40 °C with high peak power density of 56 mW cm-2 and long cycle life of over 80 h. This study provides insight of kinetically active catalyst and facilitates the ZABs application in harsh environment.

Biomass-Derived Flexible Carbon Architectures as Self-Supporting Electrodes for Energy Storage

With the swift advancement of the wearable electronic devices industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel electrode materials for flexible energy storage devices. Nonetheless, among the numerous materials investigated to date, the incorporation of metal current collectors or insulative adhesives remains requisite, which entails additional costs, unnecessary weight, and high contact resistance. At present, biomass-derived flexible architectures stand out as a promising choice in electrochemical energy device applications. Flexible self-supporting properties impart a heightened mechanical performance, obviating the need for additional binders and lowering the contact resistance. Renewable, earth-abundant biomass endows these materials with cost-effectiveness, diversity, and modulable chemical properties. To fully exploit the application potential in biomass-derived flexible carbon architectures, understanding the latest advancements and the comprehensive foundation behind their synthesis assumes significance. This review delves into the comprehensive analysis of biomass feedstocks and methods employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of flexible carbon architectures and the challenges they face is provided.

Boosting Electro- and Photo-Catalytic Activities in Atomically Thin Nanomaterials by Heterointerface Engineering

Since the discovery of graphene, two-dimensional ultrathin nanomaterials with an atomic thickness (typically <5 nm) have attracted tremendous interest due to their fascinating chemical and physical properties. These ultrathin nanomaterials, referred to as atomically thin materials (ATMs), possess inherent advantages such as a high specific area, highly exposed surface-active sites, efficient atom utilization, and unique electronic structures. While substantial efforts have been devoted to advancing ATMs through structural chemistry, the potential of heterointerface engineering to enhance their properties has not yet been fully recognized. Indeed, the introduction of bi- or multi-components to construct a heterointerface has emerged as a crucial strategy to overcome the limitations in property enhancement during ATM design. In this review, we aim to summarize the design principles of heterointerfacial ATMs, present general strategies for manipulating their interfacial structure and catalytic properties, and provide an overview of their application in energy conversion and storage, including the hydrogen evolution reaction (HER), the oxygen evolution reaction (OER), the oxygen reduction reaction (ORR), the CO2 electroreduction reaction (CO2RR), photocatalysis, and rechargeable batteries. The central theme of this review is to establish correlations among interfacial modulation, structural and electronic properties, and ATMs' major applications. Finally, based on the current research progress, we propose future directions that remain unexplored in interfacial ATMs for enhancing their properties and introducing novel functionalities in practical applications.

Gel Electrolyte with the Sodium Dodecyl Sulfate Additive for Low-Temperature Zinc-Air Batteries

Under the background of the energy crisis and the expansion of human activities, developing low-temperature batteries is of significance to provide electricity in cold conditions. Due to their low cost and high energy density, zinc-air batteries are recognized as potential batteries to overcome the disadvantage of traditional batteries. Gel electrolytes have been widely applied in low-temperature zinc-based batteries, and their anti-deforming capability makes them compatible with flexible devices. This work illustrates an A-PAA gel electrolyte with KOH solution in flexible zinc-air batteries, and with the introduction of sodium dodecyl sulfate (SDS), the cycling stability and specific capacity of the batteries at -20 °C increase. This work discusses the SDS compatibility with the gel and explores its improvement effect in low-temperature batteries for the first time. The result of this work can inspire the discovery of the applicability of more conventional electrolyte additives in cold conditions, which can improve low-tempeature battery performance via easy methods.

Synergistic Bimetallic CoCu-Codecorated Carbon Nanosheet Arrays as Integrated Bifunctional Cathodes for High-Performance Rechargeable/Flexible Zinc-Air Batteries

The unremitting exploration of well-architectured and high-efficiency oxygen electrocatalysts is promising to speed up the surface-mediated oxygen reduction/evolution reaction (ORR/OER) kinetics of rechargeable zinc-air batteries (ZABs). Herein, bimetallic CoCu-codecorated carbon nanosheet arrays (CoCu/N-CNS) are proposed as self-supported bifunctional oxygen catalysts. The integrated catalysts are in situ constructed via a simple sacrificial-templated strategy, imparting CoCu/N-CNS with 3D interconnected conductive pathways, abundant mesopores for electrolyte penetration and ion diffusion, as well as Cu-synergized Co-N_x /O reactive sites for improved catalytic activities. By incorporating a moderate amount of Cu into CoCu/N-CNS, the bifunctional activities can be further increased due to synergistic oxygen electrocatalysis. Consequently, the optimized CoCu/N-CNS realizes a low overall overpotential of 0.64 V for OER and ORR and leads to high-performance liquid ZABs with high gravimetric energy (879.7 Wh kg^-1 ), high peak power density (104.3 mW cm^-2 ), and remarkable cyclic stability upon 400 h/1000 cycles at 10 mA cm^-2 . More impressively, all-solid-state flexible ZABs assembled with the CoCu/N-CNS cathode exhibit superior rate performance and exceptional mechanical flexibility under arbitrary bending conditions. This CoCu/N-CNS monolith holds significant potential in advancing cation-modulated multimetallic electrocatalysts and multifunctional nanocatalysts.

Rational Design of Flexible Zn-Based Batteries for Wearable Electronic Devices

The advent of 5G and the Internet of Things has spawned a demand for wearable electronic devices. However, the lack of a suitable flexible energy storage system has become the "Achilles' Heel" of wearable electronic devices. Additional problems during the transformation of the battery structure from conventional to flexible also present a severe challenge to the battery design. Flexible Zn-based batteries, including Zn-ion batteries and Zn-air batteries, have long been considered promising candidates due to their high safety, eco-efficiency, substantial reserve, and low cost. In the past decade, researchers have come up with elaborate designs for each portion of flexible Zn-based batteries to improve the ionic conductivities, mechanical properties, environment adaptabilities, and scalable productions. It would be helpful to summarize the reported strategies and compare their pros and cons to facilitate further research toward the commercialization of flexible Zn-based batteries. In this review, the current progress in developing flexible Zn-based batteries is comprehensively reviewed, including their electrolytes, cathodes, and anodes, and discussed in terms of their synthesis, characterization, and performance validation. By clarifying the challenges in flexible Zn-based battery design, we summarize the methodology from previous investigations and propose challenges for future development. In the end, a research paradigm of Zn-based batteries is summarized to fit the burgeoning requirement of wearable electronic devices in an iterative process, which will benefit the future development of Zn-based batteries.

Opportunities of Flexible and Portable Electrochemical Devices for Energy Storage: Expanding the Spotlight onto Semi-solid/Solid Electrolytes

The ever-increasing demand for flexible and portable electronics has stimulated research and development in building advanced electrochemical energy devices which are lightweight, ultrathin, small in size, bendable, foldable, knittable, wearable, and/or stretchable. In such flexible and portable devices, semi-solid/solid electrolytes besides anodes and cathodes are the necessary components determining the energy/power performances. By serving as the ion transport channels, such semi-solid/solid electrolytes may be beneficial to resolving the issues of leakage, electrode corrosion, and metal electrode dendrite growth. In this paper, the fundamentals of semi-solid/solid electrolytes (e.g., chemical composition, ionic conductivity, electrochemical window, mechanical strength, thermal stability, and other attractive features), the electrode-electrolyte interfacial properties, and their relationships with the performance of various energy devices (e.g., supercapacitors, secondary ion batteries, metal-sulfur batteries, and metal-air batteries) are comprehensively reviewed in terms of materials synthesis and/or characterization, functional mechanisms, and device assembling for performance validation. The most recent advancements in improving the performance of electrochemical energy devices are summarized with focuses on analyzing the existing technical challenges (e.g., solid electrolyte interphase formation, metal electrode dendrite growth, polysulfide shuttle issue, electrolyte instability in half-open battery structure) and the strategies for overcoming these challenges through modification of semi-solid/solid electrolyte materials. Several possible directions for future research and development are proposed for going beyond existing technological bottlenecks and achieving desirable flexible and portable electrochemical energy devices to fulfill their practical applications. It is expected that this review may provide the readers with a comprehensive cross-technology understanding of the semi-solid/solid electrolytes for facilitating their current and future researches on the flexible and portable electrochemical energy devices.

Carbon-based composites for rechargeable zinc-air batteries: A mini review

Rechargeable zinc-air batteries (ZABs) have gained a significant amount of attention as next-generation energy conversion and storage devices owing to their high energy density and environmental friendliness, as well as their safety and low cost. The performance of ZABs is dominated by oxygen electrocatalysis, which includes the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER). Therefore, it is crucial to develop effective bifunctional oxygen electrocatalysts that are both highly active and stable. Carbon-based materials are regarded as reliable candidates because of their superior electrical conductivity, low price, and high durability. In this Review, we briefly introduce the configuration of ZABs and the reaction mechanism of bifunctional ORR/OER catalysts. Then, the most recent developments in carbon-based bifunctional catalysts are summarized in terms of carbon-based metal composites, carbon-based metal oxide composites, and other carbon-based composites. In the final section, we go through the significant obstacles and potential future developments for carbon-based bifunctional oxygen catalysts for ZABs.

Poly(acrylic acid)-Based Composite Gel Polymer Electrolytes with High Mechanical Strength and Ionic Conductivity toward Flexible Zinc-Air Batteries with Long Cycling Lifetime

The rapid development of portable, flexible, and wearable devices motivates the requirement for flexible zinc-air batteries (FZABs) not only to provide high energy density but also to have sufficient deformability for wearer comfort. The gel polymer electrolyte (GPE) serves as the core part of the FZABs, playing a key function in the battery's practical output performance such as discharge voltage, energy density, and cycling life. Unfortunately, ascribed to its high water absorption, the GPE regularly shows comparatively poor mechanical strength, which is difficult to offer sufficient physical support between electrodes. Herein, we report an optimized poly(acrylic acid) (PAA)-based composite GPE with the aluminum oxide (Al2O3) filler and apply it for FZAB. The mechanical strength, electrolyte absorption capacity, electrolyte retention ability, and ionic conductivity of the PAA-Al2O3 gel polymers and corresponding GPEs were investigated. The results indicate that the above performances of polymers and corresponding GPEs depend to a considerable extent on the content of the addition of Al2O3 particles. When 20 wt.% Al2O3 is added to the PAA polymer, the obtained PAA-20 wt.% Al2O3 gel polymer exhibits improved mechanical strength. The corresponding PAA-20 wt.% Al2O3 GPE shows a high ionic conductivity of 186 mS cm-1 and pleasurable electrolyte retention capability. This optimized GPE enables the assembled FZAB to display a long cycling lifetime of 384 h, a large power density of 77.7 mW cm-2, and excellent discharge performance. Moreover, the integrated FZAB can power various electronic devices, demonstrating its outstanding practicability and extensibility as a flexible power source.

A Honeycomb-like Ammonium-Ion Fiber Battery with High and Stable Performance for Wearable Energy Storage

Aqueous ammonium-ion batteries have attracted intense interest lately as promising energy storage systems due to the price advantage and fast charge/discharge capability of ammonium-ion redox reactions. However, the research on the strength and energy storage characteristics of ammonium-ion fiber batteries is still limited. In this study, an ammonium-ion fiber battery with excellent mechanical strength, flexibility, high specific capacity, and long cycle-life has been developed with a robust honeycomb-like ammonium vanadate@carbon nanotube (NH₄V₄O₁₀@CNT) cathode. The fiber electrode delivers a steady specific capacity of 241.06 mAh cm^-3 at a current of 0.2 mA. Moreover, a fiber full cell consisting of an NH₄V₄O₁₀@CNT cathode and a PANI@CNT anode exhibits a specific capacity of 7.27 mAh cm^-3 at a current of 0.3 mA and retains a high capacity retention of 72.1% after 1000 cycles. Meanwhile, it shows good flexibility and superior electrochemical performance after 500 times bending or at different deformation states. This work offers a reference for long-cycle, flexible fibrous ammonium-ion batteries.

Interfacial Electron Redistribution of FeCo2S4/N-S-rGO Boosting Bifunctional Oxygen Electrocatalysis Performance

Developing bifunctional catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is essential for the development of zinc–air batteries (ZABs), but several challenges remain in terms of bifunctional activity. FeCo2S4/N-S-rGO was prepared by in situ homogeneous growth of bimetallic sulfide FeCo2S4 on N, S-doped reduced graphene oxide. FeCo2S4/N-S-rGO exhibits a half-wave potential of 0.89 V for ORR and an overpotential of 0.26 V at 10 mA cm−2 for OER, showing significantly bifunctional activity superior to Pt/C (0.85 V) and RuO2 (0.41 V). Moreover, the FeCo2S4/N-S-rGO assembled ZAB shows a superior specific capacity and a power density of 259.13 mW cm−2. It is demonstrated that the interfacial electron redistribution between FeCo2S4 nanoparticles and heteroatom-doped rGO matrix can efficiently improve the electrochemical performance of the catalyst. The results provide new insights into the preparation of high-capability composite catalysts combining transition metal sulfides with carbon materials for applications in ZABs.

Hierarchically Nanostructured Solid-State Electrolyte for Flexible Rechargeable Zinc-Air Batteries

The construction of safe and environmentally-benign solid-state electrolytes (SSEs) with intrinsic hydroxide ion-conduction for flexible zinc-air batteries is highly desirable yet extremely challenging. Herein, hierarchically nanostructured CCNF-PDIL SSEs with reinforced concrete architecture are constructed by nanoconfined polymerization of dual-cation ionic liquid (PDIL, concrete) within a robust three-dimensional porous cationic cellulose nanofiber matrix (CCNF, reinforcing steel), where plenty of penetrating ion-conductive channels are formed and undergo dynamic self-rearrangement under different hydrated levels. The CCNF-PDIL SSEs synchronously exhibit good flexibility, mechanical robustness, superhigh ion conductivity of 286.5 mS cm^-1 , and decent water uptake. The resultant flexible solid-state zinc-air batteries deliver a high-power density of 135 mW cm^-2 , a specific capacity of 775 mAh g^-1 and an ultralong cycling stability with continuous operation of 240 hours for 720 cycles, far outperforming those of the state-of-the-art solid-state batteries. The marriage of biomaterials with the diversity of ionic liquids creates enormous opportunities to construct advanced SSEs for solid-state batteries.

Hierarchical Core-Shell Co2 N/CoP Embedded in N, P-doped Carbon Nanotubes as Efficient Oxygen Reduction Reaction Catalysts for Zn-air Batteries

Projecting a cost-effective and highly efficient electrocatalyst for the oxygen reaction reduction (ORR) counts a great deal for Zn-air batteries. Herein, a hierarchical core-shell ORR catalyst (Co₂ N/CoP@PNCNTs) is developed by embedding cobalt phosphides and/or cobalt nitrides as the core into N, P-doped carbon nanotubes (PNCNTs) as the shell via one-step carbonization, nitridation, and phosphorization of pyrolyzing Co-MOF precursor. The globally N, P-doped structure of Co₂ N/CoP@PNCNTs demonstrates an outstanding electrocatalytic activity in the alkaline solution with the onset and half-wave potentials of 1.07 and 0.85 V respectively. Moreover, a Zn-air battery assembled from Co₂ N/CoP@PNCNTs as the air cathode delivers an open circuit potential of 1.49 V, a maximum power density of 151.1 mW cm^-2 and a specific capacity of 823.8 mAh kg^-1 . It is reflected that Co₂ N/CoP@PNCNTs provides a long-term durability with a slight decline of 15 h in the chronoamperometry measurement and an excellent charge-discharge stability with negligible voltage decay for 150 h at 10 mA cm^-2 in Zn-air batteries. The results reveal that Co₂ N/CoP@PNCNTs has superiority over most Co-N_x -C or Co_x P@C catalysts reported so far. The excellent catalytic properties and stability of Co₂ N/CoP@PNCNTs derive from synergistic effects between Co₂ N/CoP and mesoporous N, P-doped carbon nanotubes.

Bioinspired Tough Solid-State Electrolyte for Flexible Ultralong-Life Zinc-Air Battery

Manufacturing advanced solid-state electrolytes (SSEs) for flexible rechargeable batteries becomes increasingly important but remains grand challenge. The sophisticated structure of robust animal dermis and good water-retention of plant cell in nature grant germane inspirations for designing high-performance SSEs. Herein, tough bioinspired SSEs with intrinsic hydroxide ion (OH^- ) conduction are constructed by in situ formation of OH^- conductive ionomer network within a hollow-polymeric-microcapsule-decorated hydrogel polymer network. By virtue of the bioinspired design and dynamic dual-penetrating network structure, the bioinspired SSEs simultaneously obtain mechanical robustness with 1800% stretchability, good water uptake of 107 g g^-1 and water retention, and superhigh ion conductivity of 215 mS cm^-1 . The nanostructure of bioinspired SSE and related ion-conduction mechanism are revealed and visualized by molecular dynamics simulation, where plenty of compact and superfast ion-transport channels are constructed, contributing to superhigh ion conductivity. As a result, the flexible solid-state zinc-air batteries assembled with bioinspired SSEs witness high power density of 148 mW cm^-2 , specific capacity of 758 mAh g^-1 and ultralong cycling stability of 320 h as well as outstanding flexibility. The bioinspired methodology and deep insight of ion-conduction mechanism will shed light on the design of advanced SSEs for flexible energy conversion and storage systems.

Potassium Cobalt Pyrophosphate as a Nonprecious Bifunctional Electrocatalyst for Zinc-Air Batteries

Economic and sustainable (ecological) energy storage forms a major pillar of the global energy sector. Bifunctional electrocatalysts, based on oxygen electrolysis, play a key role in the development of rechargeable metal-air batteries. Pursuing precious metal-free economic catalysts, here, we report K₂CoP₂O₇ pyrophosphate as a robust cathode for secondary zinc-air batteries with efficient oxygen evolution and oxygen reduction (OER||ORR) activity. Prepared by autocombustion, nanoscale K₂CoP₂O₇ exhibited excellent oxygen reduction and evolution reactions among all phosphate-based electrocatalysts. In particular, the OER activity surpassed that of commercial RuO₂ with low overpotential (0.27 V). First-principles calculations revealed that the bifunctional activity is rooted in the Co active site with the CoO₅ local coordination in the most stable (110) surface. This nanostructured (tetragonal) pyrophosphate can be harnessed as an economic bifunctional catalyst for zinc-air batteries.

Synergetic Chemistry and Interface Engineering of Hydrogel Electrolyte to Strengthen Durability of Solid-State Zn-Air Batteries

For the challenging pursuit of high energy efficiency and mechanical tolerance in flexible solid-state Zn-air batteries (FSZABs), a hydrogel electrolyte (HE) consisting of dual-network crosslinked polyacrylic acid-Fe³⁺ -chitosan (PAA-Fe³⁺ -CS) polymer host infiltrated with a mixed aqueous electrolyte of NH₄ Cl and ZnCl₂ is developed. The absorbed near-neutral electrolyte renders the HE high ionic conductivity but low corrosiveness to both electrocatalysts and Zn metal anode (ZMA), ensuring more stable Zn-OH-O₂ chemistry compared to that in strong alkaline electrolyte and thus endowing the assembled FSZABs with a landmark cycle life up to 120 h (5 mA cm^-2 ). More intriguingly, the CS molecular beams introduced into the PAA hydrogel backbone will precipitate and fold subjecting to the Hofmeister effect when saturated with the near-neutral electrolyte, which can effectively enhance the interfacial adhesion strength of the HE on both air cathode and ZMA, achieving reliable and robust bonding between them. Thus, the FSZABs simultaneously exhibited a superior tolerance to repeated mechanical deformation during operation, allowing more than 360 continuous bending-recovery cycles without any decline in voltage efficiency. The ingenious chemistry and interface synergetic engineering on the crucial HEs provides a rational methodology to realize boosted electrochemical and mechanical durability of FSZABs forward for future practical implementation.

Ru-incorporated Co3O4 nanoparticles from self-sacrificial ZIF-67 template as efficient bifunctional electrocatalysts for rechargeable metal-air battery

Ru-incorporated Co₃O₄ nanoparticles have been synthesized from self-sacrificial ZIF-67 template and utilized as efficient electrocatalysts towards oxygen reduction and evolution reactions (ORR and OER). Amongst, Ru@Co₃O₄-1.0 exhibited the optimum electrocatalytic behavior with an ultra-low potential gap (0.84 V) between the OER potential (1.61 V at 10 mA cm^-2) and ORR half-wave potential (0.77 V). The zinc-air battery using Ru@Co₃O₄-1.0 as a cathode presented high specific capacity (788.1 mAh g^-1) and power density (101.2 mW cm^-2). Meanwhile, this battery possessed relatively lower voltage gap and higher cycling stability compared with the commercial Pt/C-based one. Ruthenium incorporation induced remarkable lattice expansion of Co₃O₄ and engineered more oxygen vacancies, promoting the lattice oxygen mobility from the subsurface/bulk phase onto surface. All these properties were recognized to be the crucial parameters for electrocatalytic activity improvement. This work provided a facile approach to design highly active metal oxide with broad potentiality for rechargeable metal-air batteries.

Current advances and challenges in nanosheet-based wearable power supply devices

Nowadays, wearable devices mainly exist in the form of portable accessories with various functions, connecting various kinds of terminals like mobile phones to form various wearable systems. In a wearable system, the wearable power supply device is the key component as energy dispenser for all devices. Nanosheets, a kind of two-dimensional material, which always displays a high surface-to-volume ratio and thus is lightweight and has remarkable conductive as well as electrochemical properties, have become the optimal choice for wearable power supply devices. The development and status of nanosheet-based wearable power supply devices including nanosheet-based wearable batteries, nanosheet-based wearable supercapacitors, nanosheet-based wearable self-powered energy suppliers are introduced in this article. Besides, the future opportunities and challenges of wearable devices are discussed.

Co3O4 Nanoneedle Array Grown on Carbon Fiber Paper for Air Cathodes towards Flexible and Rechargeable Zn-Air Batteries

An economical and efficient method is developed for preparing flexible cathodes. In this work, a dense mesoporous Co₃O₄ layer was first hydrothermally grown in situ on the surface of chopped carbon fibers (CFs), and then carbon fiber paper (Co₃O₄/CP) was prepared by a wet papermaking process as a flexible zinc-air battery (ZAB). The high-performance air cathode utilizes the high specific surface area of a single chopped carbon fiber, which is conducive to the deposition and adhesion of the Co₃O₄ layer. Through the wet papermaking process, Co₃O₄/CP has ultra-thin, high mechanical stability and excellent electrical conductivity. In addition, the assembled ZAB exhibits relatively excellent electrochemical performance, with a continuous cycle of more than 180 times at a current density of 2 mA·cm⁻². The zinc-air battery can maintain a close fit and work stably and efficiently even under high bending conditions. This process of combining single carbon fibers to prepare ultra-thin, high-density, high-conductivity carbon fiber paper through a papermaking process has huge application potential in the field of flexible wearables.

Toward Flexible Zinc-Air Batteries with Self-Supported Air Electrodes

The compelling demand for higher energy performance, flexibility, and miniaturization is the main driving force of the energy storage and conversion industry's quest for flexible devices based on new integration and fabrication process. Herein, the recent advances on the development of flexible zinc-air batteries based on self-supported air electrodes are summarized, focusing on the multiscale and systematic design principles for the design of flexible air electrodes. With the electrocatalytic activity regulation and structural engineering strategies, the rational design of self-supported air electrodes is discussed in integrated devices to underpin the good flexibility for wearable requirement. The perspectives on promising developments of flexible zinc-air batteries and the accumulated knowledge from other flexible devices are also addressed for promoting the advances on flexible zinc-air batteries.

Nickel decorated manganese oxynitride over graphene nanosheets as highly efficient visible light driven photocatalysts for acetylsalicylic acid degradation

In this work, we prepared nanocomposites of nickel-decorated manganese oxynitride on graphene nanosheets and demonstrated them as photocatalysts for degradation of acetylsalicylic acid (ASA). The catalyst exhibited a high degradation efficiency over ASA under visible light irradiation and an excellent structural stability after multiple uses. Compared to manganese oxide (MnO) and manganese oxynitride (MnON) nanoparticles, larger specific surface area and smaller band gap were observed for the nanocomposite accounting for the enhanced photocatalytic efficiency. Besides the compositional effect of the catalyst, we also examined the influence of various experimental parameters on the degradation of ASA such as initial concentration, catalyst dose, initial pH and additives. The best performance was obtained for the nanocomposite when the catalyst dose was 10 mg/mL and the initial pH 3. Detection of intermediates during photocatalysis showed that ASA undergoes hydroxylation, demethylation, aromatization, ring opening, and finally complete mineralization into CO₂ and H₂O by reactive species. For practical applications as a photocatalyst, cytotoxicity of the nanocomposite was also evaluated, which revealed its insignificant impact on the cell viability. These results suggest the nanocomposite of nickel-decorated manganese oxynitride on graphene nanosheets as a promising photocatalyst for the remediation of ASA-contaminated water.

Atomically Thin Materials for Next-Generation Rechargeable Batteries

Atomically thin materials (ATMs) with thicknesses in the atomic scale (typically <5 nm) offer inherent advantages of large specific surface areas, proper crystal lattice distortion, abundant surface dangling bonds, and strong in-plane chemical bonds, making them ideal 2D platforms to construct high-performance electrode materials for rechargeable metal-ion batteries, metal-sulfur batteries, and metal-air batteries. This work reviews the synthesis and electronic property tuning of state-of-the-art ATMs, including graphene and graphene derivatives (GE/GO/rGO), graphitic carbon nitride (g-C₃N₄), phosphorene, covalent organic frameworks (COFs), layered transition metal dichalcogenides (TMDs), transition metal carbides, carbonitrides, and nitrides (MXenes), transition metal oxides (TMOs), and metal-organic frameworks (MOFs) for constructing next-generation high-energy-density and high-power-density rechargeable batteries to meet the needs of the rapid developments in portable electronics, electric vehicles, and smart electricity grids. We also present our viewpoints on future challenges and opportunities of constructing efficient ATMs for next-generation rechargeable batteries.

Textiles in soft robots: Current progress and future trends

Soft robotics have substantial benefits of safety, adaptability, and cost efficiency compared to conventional rigid robotics. Textiles have applications in soft robotics either as an auxiliary material to reinforce the conventional soft material or as an active soft material. Textiles of various types and configurations have been fabricated into key components of soft robotics in adaptable formats. Despite significant advancements, the efficiency and characteristics of textile actuators in practical applications remain unsatisfactory. To address these issues, novel structural and material designs as well as new textile technologies have been introduced. Herein, we aim at giving an insight into the current state of the art in textile technology for soft robotic manufacturing. We firstly discuss the fundamental actuation mechanisms for soft robotics. We then provide a critical review on the recently developed functional textiles as reinforcements, sensors, and actuators in soft robotics. Finally, the future trends and current strategies that can be employed in textile-based actuator manufacturing process have been explored to address the critical challenges in soft robotics.

Heuristic Iron-Cobalt-Mediated Robust pH-Universal Oxygen Bifunctional Lusters for Reversible Aqueous and Flexible Solid-State Zn-Air Cells

Rechargeable aqueous zinc-air cells (ZACs) promise an extremely safe and high energy technology. However, they are still significantly limited by sluggish electrochemical kinetics and irreversibility originating from the parasitic reactions of the bifunctional catalysts and electrolytes. Here, we report the preferential in situ building of interfacial structures featuring the edge sites constituted by FeCo single/dual atoms with the integration of Co sites in the nitrogenized graphitic carbon frameworks (FeCo SAs@Co/N-GC) by electronic structure modulation approach. Compared to commercial Pt/C and RuO₂, FeCo SAs@Co/N-GC reveals exceptional electrochemical performance, reversible redox kinetics, and durability toward oxygen reduction and evolution reactions under universal pH environments, i.e., alkaline, neutral, and acidic, due to synergistic effect at interfaces and preferred charge/mass transfer. The aqueous (alkaline, nonalkaline, and acidic electrolytes) ZACs constructed with a FeCo SAs@Co/N-GC cathode tolerate stable operations, have significant reversibility, and have the highest energy densities, outperforming those of noble metal counterparts and state-of-the-art ZACs in the ambient atmosphere. Additionally, flexible solid-state ZACs demonstrate excellent mechanical and electrochemical performances with a highest power density of 186 mW cm^-2, specific capacity of 817 mAh g_Zn^-1, energy density of 1017 Wh kg_Zn^-1, and cycle life >680 cycles with extremely harsh operating conditions, which illustrates the great potential of triphasic catalyst for green energy storage technologies.

Development of high performance alpha-Co(OH)2/reduced graphene oxide microfilm for flexible in-sandwich and planar micro-supercapacitors

Herein, a series of alpha-Co(OH)₂/reduced graphene oxide (rGO) microfilms and film-based nanodevices were developed via a new scalable technique. Due to the unique hexagonal nanoplates of ultrathin alpha-Co(OH)₂ and the intrinsically conductive nature of rGO sheets, such thin films not only can improve the conductivity of alpha-Co(OH)₂ and prevent the re-stacking of alpha-Co(OH)₂ and rGO sheets but also short the transport routes of electrons and ions between the electrode and the electrolyte. The optimized alpha-Co(OH)₂/rGO flexible electrode presents high specific capacitance (273.86 mF/cm² at 0.1 mA/cm²), advanced rate capability, and excellent coulombic efficiency. Simultaneously, in-sandwich symmetric and asymmetric supercapacitors assembled with polyvinyl alcohol-KOH gel as the solid-state electrolyte achieved high areal and volumetric specific capacitances. Furthermore, a self-assembled planar alpha-Co(OH)₂/rGO micro-supercapacitor (MSC) delivers high specific area capacitance (130F/cm² at 0.5 mA/cm²) and excellent energy density (20 mWh/cm³@56 mW/cm³), which are superior to most of the recently reported carbon-based and metal hydroxides/oxides/sulfides-based planar MSCs. Also, our planar MSC shows excellent cycling performance, good flexibility, and mechanical stability. This work promotes the syntheses of other two-dimensional metal hydroxides/rGO composite film for high-performance flexible micro-electronics.