ZIF‐8 MOF Encapsulated Co‐porphyrin, an Efficient Electrocatalyst for Water Oxidation in a Wide pH Range: Works Better at Neutral pH

Superprotonic Conductivity by Synergistic Blending of Coordination Polymers with Organic Polymers: Fabrication of Durable and Flexible Proton Exchange Membranes

Creation of an efficient and cost-effective proton exchange membrane (PEM) has emerged as a propitious solution to address the challenges of renewable energy development. Coordination polymers (CPs) have garnered significant interest due to their multifunctional applications and moldability, along with long-range order. To leverage the potential of CPs in fuel cells, it is essential to integrate microcrystalline CPs into organic polymers to prepare membranes and avoid grain boundary issues. In this study, we designed and synthesized CPs containing imidazole and sulfonate moieties via gel-to-crystal transformation. The integration of CPs into the PVDF-PVP matrix resulted in superprotonic conductivity in the order of 10-2 S cm-1 at room temperature (30 °C) and 98 % RH. The proton conductivity achieved with CP-integrated composite membrane was 4.69×10-2 S cm-1 at 80 °C and 98 % RH, the highest among all CP/MOF-integrated PVDF-PVP membranes under hydrous conditions. The excellent compatibility of CPs with PVDF-PVP produced highly flexible membranes with superior mechanical, chemical, and thermal stability. About 25 times higher proton conductivity value was achieved with membrane, compared to intrinsic CPs, at RT and 98 % RH. Thus, we present a cost-effective CP-integrated mixed-matrix membrane with superprotonic conductivity and long-term durability for cutting-edge fuel cell development.

Atomically Dispersed High-Active Site Density Copper Electrocatalyst for the Reduction of Oxygen

Enlarging the M-Nx active-site density is an effective route to enhance the ORR performance of M-N-C catalysts. In this work, a single-atom catalyst Cu-N@Cu-N-C with enlarged Cu-N4 active site density was prepared by the second doping and pyrolysis (SDP) of Cu-N-C derived from Cu-doped zeolite imidazole frameworks. The half-wave potentials of Cu-N@Cu-N-C were measured as 0.85 V in alkaline electrolyte and 0.75 V in acidic media, which was 50 mV and 60 mV higher than that of Cu-N-C, respectively. N2 adsorption-desorption isotherm curves and corresponding pore distribution analysis were used to verify the successful filling of additional Cu and N in micropores of Cu-N-C after SDP. The obvious increase in Cu contents for Cu-N@Cu-N-C (1.92 wt%) compared with Cu-N-C (0.88 wt%) tested by ICP demonstrated the successful doping of Cu into Cu-N-C. XAFS analysis confirmed the presence of Cu-N4 single-atom active centers in Cu-N@Cu-N-C. The N 1 s high-resolution XPS results proved a great increase in Cu-N4 contents from 13.15% for Cu-N-C to 18.36% for Cu-N@Cu-N-C. The enhanced ORR performance of Cu-N@Cu-N-C was attributed to the enlargement of Cu-N4 active site density, providing an effective route for the preparation of efficient and low-cost ORR catalysts.

2D Metal Porphyrin-Based MOFs and ZIF-8 Composite-Derived Carbon Materials Containing M-Nx Active Sites as Bifunctional Electrocatalysts for Zinc-Air Batteries

The main impediment to the development of zinc-air batteries is the sluggish kinetics of the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER). Transition metal N-doped carbon catalysts offer a promising alternative to noble metal catalysts, with metal-organic framework (MOF)-derived carbon material catalysts being particularly noteworthy. Here, we synthesized MxP-Z-C carbon catalysts by combining two-dimensional (2D) metal porphyrin-based MOFs (MxPMFs, x = Fe, Co, Ni, Mn) and three-dimensional zeolitic imidazole framework-8 (ZIF-8) through electrostatic interaction, followed by carbonization. ZIF-8 was inserted between the layers of MxPMFs to prevent its Π-Π stacking, allowing the active sites to become fully exposed. MxP-Z-C demonstrated an impressive catalytic activity for both the ORR and the OER reactions. Among them, FeP-Z-C showed the best catalytic activity. The half-wave potential for ORR was 0.92 V (vs the reversible hydrogen electrode (RHE)), while the overpotential for the OER was 290 mV. In addition, the zinc-air battery assembled by FeP-Z-C exhibited high power density (133.14 mW cm-2) and significant specific capacity (816 mAh gZn-1), indicating considerable potential as a bifunctional catalyst for electronic devices.

Research progress on MOFs and their derivatives as promising and efficient electrode materials for electrocatalytic hydrogen production from water

Hydrogen energy is considered to be the most potential "ultimate energy source" due to its high combustion calorific value, cleanliness, and pollution-free characteristics. Furthermore, the production of hydrogen via the electrolysis of water has the advantages of simplicity, high efficiency, environmentally safe, and high-purity hydrogen. However, it is also associated with issues such as high-power consumption for the reaction and limited large-scale application of noble metal catalysts. Metal-organic frameworks (MOFs) are porous composite materials composed of metal ions and organic functional groups through orderly coordination with large specific surface areas and large porosity. Herein, we focus on the research status of MOFs and their transition metal derivatives for electrocatalytic water splitting to produce hydrogen and briefly describe the reaction mechanism and evaluation parameters of the electrocatalytic hydrogen evolution and oxygen evolution reactions. Furthermore, the relationship between the catalytic behavior and catalytic activity of different MOF-based catalysts and their morphology, elemental composition, and synthetic strategy is analyzed and discussed. The reasons for the excellent activity and poor stability of the original MOF materials for the electrolysis of water reaction are shown through analysis, and using various means to improve the catalytic activity by changing the electronic structure, active sites, and charge transfer rate, MOF-based catalysts were obtained. Finally, we present perspectives on the future development of MOFs for the electrocatalytic decomposition of water.

Metal-Organic Frameworks as Electrocatalysts

Transition metal complexes are well-known homogeneous electrocatalysts. In this regard, metal-organic frameworks (MOFs) can be considered as an ensemble of transition metal complexes ordered in a periodic arrangement. In addition, MOFs have several additional positive structural features that make them suitable for electrocatalysis, including large surface area, high porosity, and high content of accessible transition metal with exchangeable coordination positions. The present review describes the current state in the use of MOFs as electrocatalysts, both as host of electroactive guests and their direct electrocatalytic activity, particularly in the case of bimetallic MOFs. The field of MOF-derived materials is purposely not covered, focusing on the direct use of MOFs or its composites as electrocatalysts. Special attention has been paid to present strategies to overcome their poor electrical conductivity and limited stability.

Hydrogen Evolution Reaction, Electrochemical CO2 Reduction, and Oxidative Photodegradation of Organic Dyes Catalyzed by Co(II) Trimethoxy-Meso-Arylporphyrin

In search of robust catalysts for redox transformations such as the hydrogen evolution reaction (HER) or CO2 to CO reduction, we stepped on the previously reported meso-tetrakis(3,4,5-trimethoxyphenyl)porphyrinato cobalt(II) complex [Co(TTMPP)]. We prepared [Co(TTMPP)] in good yields and characterized it by IR, UV-vis absorption, photoluminescence spectroscopy, and cyclic voltammetry (CV). The [Co(TTMPP)] was used as a homogeneous catalyst for the electrochemical formation of H2 (HER) in DMF (N,N’-dimethylformamide)/TFA (trifluoroacetic acid) and DMF/EtN3BF4 solutions, with high faradic efficiencies (FE). Additionally, the reduction of CO2 to CO in DMF under a CO2 atmosphere was catalyzed in DMF/TFE (TFE = 2,2,2-trifluoroethanol) and DMF/PhOH with high FE and only traces of H2 as a by-product. Turnover frequencies of 15.80 or 9.33 s−1, respectively were determined from CV experiments or controlled potential electrolysis in the presence of 1eq. TFE. They were lower with PhOH as proton source with 13.85 or 8.31 s−1, respectively. Further, [Co(TTMPP)] as a solid catalyst (suspension) allowed the photodecomposition of the organic dyes methylene blue (MB) and rhodamine B (RhB) using H2O2 under visible light irradiation. The photocatalyst was photostable over five cycles. A photocatalytic mechanism was proposed based on trapping experiments of reactive oxygen species.

Metalloporphyrin Metal–Organic Frameworks: Eminent Synthetic Strategies and Recent Practical Exploitations

The emergence of metal–organic frameworks (MOFs) in recent years has stimulated the interest of scientists working in this area as one of the most applicable archetypes of three-dimensional structures that can be used as promising materials in several applications including but not limited to (photo-)catalysis, sensing, separation, adsorption, biological and electrochemical efficiencies and so on. Not only do MOFs have their own specific versatile structures, tunable cavities, and remarkably high surface areas, but they also present many alternative procedures to overcome emerging obstacles. Since the discovery of such highly effective materials, they have been employed for multiple uses; additionally, the efforts towards the synthesis of MOFs with specific properties based on planned (template) synthesis have led to the construction of several promising types of MOFs possessing large biological or bioinspired ligands. Specifically, metalloporphyrin-based MOFs have been created where the porphyrin moieties are either incorporated as struts within the framework to form porphyrinic MOFs or encapsulated inside the cavities to construct porphyrin@MOFs which can combine the peerless properties of porphyrins and porous MOFs simultaneously. In this context, the main aim of this review was to highlight their structure, characteristics, and some of their prominent present-day applications.

A New Supramolecular Tetraruthenated Cobalt (II) Porphyrazine Displaying Outstanding Electrocatalytical Performance in Oxygen Evolution Reaction

A new supramolecular electrocatalyst for Oxygen Evolution Reaction (OER) was synthesized from a central multibridging cobalt tetrapyridylporphyrazine (CoTPyPz) species by attaching four [Ru(bpy)₂Cl]⁺ groups. Both CoTPyPz and the tetraruthenated cobalt porphyrazine species, TRuCoTPyPz, form very homogenous molecular films just by dropcasting their methanol solutions onto GCE electrodes. Such films exhibited low overpotentials for O₂ evolution, e.g., 560 e 340 mV, respectively, displaying high stability, typically exceeding 15 h. The kinetic parameters obtained from the Tafel plots showed that the peripheral complexes are very important for the electrocatalytic activity. Hyperspectral Raman images taken along the electrochemical process demonstrated that the cobalt center is the primary active catalyst site, but its performance is enhanced by the ruthenium complexes, which act as electron-donating groups, in the supramolecular system.

Recent Advances in Porphyrin-Based Systems for Electrochemical Oxygen Evolution Reaction

Oxygen evolution reaction (OER) plays a pivotal role in the development of renewable energy methods, such as water-splitting devices and the use of Zn–air batteries. First-row transition metal complexes are promising catalyst candidates due to their excellent electrocatalytic performance, rich abundance, and cheap price. Metalloporphyrins are a class of representative high-efficiency complex catalysts owing to their structural and functional characteristics. However, OER based on porphyrin systems previously have been paid little attention in comparison to the well-described oxygen reduction reaction (ORR), hydrogen evolution reaction, and CO2 reduction reaction. Recently, porphyrin-based systems, including both small molecules and porous polymers for electrochemical OER, are emerging. Accordingly, this review summarizes the recent advances of porphyrin-based systems for electrochemical OER. Firstly, the electrochemical OER for water oxidation is discussed, which shows various methodologies to achieve catalysis from homogeneous to heterogeneous processes. Subsequently, the porphyrin-based catalytic systems for bifunctional oxygen electrocatalysis including both OER and ORR are demonstrated. Finally, the future development of porphyrin-based catalytic systems for electrochemical OER is briefly prospected.

CO2 to CO Electroreduction, Electrocatalytic H2 Evolution, and Catalytic Degradation of Organic Dyes Using a Co(II) meso-Tetraarylporphyrin

The meso-tetrakis(4-(trifluoromethyl)phenyl)porphyrinato cobalt(II) complex [Co(TMFPP)] was synthesised in 93% yield. The compound was studied by 1H NMR, UV-visible absorption, and photoluminescence spectroscopy. The optical band gap Eg was calculated to 2.15 eV using the Tauc plot method and a semiconducting character is suggested. Cyclic voltammetry showed two fully reversible reduction waves at E1/2 = -0.91 V and E1/2 = -2.05 V vs. SCE and reversible oxidations at 0.30 V and 0.98 V representing both metal-centred (Co(0)/Co(I)/Co(II)/Co(III)) and porphyrin-centred (Por2-/Por-) processes. [Co(TMFPP)] is a very active catalyst for the electrochemical formation of H2 from DMF/acetic acid, with a Faradaic Efficiency (FE) of 85%, and also catalysed the reduction of CO2 to CO with a FE of 90%. Moreover, the two triarylmethane dyes crystal violet and malachite green were decomposed using H2O2 and [Co(TMFPP)] as catalyst with an efficiency of more than 85% in one batch.

Electrocatalytic Water Splitting: From Harsh and Mild Conditions to Natural Seawater

Electrocatalytic water splitting is regarded as the most effective pathway to generate green energy-hydrogen-which is considered as one of the most promising clean energy solutions to the world's energy crisis and climate change mitigation. Although electrocatalytic water splitting has been proposed for decades, large-scale industrial hydrogen production is hindered by high electricity cost, capital investment, and electrolysis media. Harsh conditions (strong acid/alkaline) are widely used in electrocatalytic mechanism studies, and excellent catalytic activities and efficiencies have been achieved. However, the practical application of electrocatalytic water splitting in harsh conditions encounters several obstacles, such as corrosion issues, catalyst stability, and membrane technical difficulties. Thus, the research on water splitting in mild conditions (neutral/near neutral), even in natural seawater, has aroused increasing attention. However, the mechanism in mild conditions or natural seawater is not clear. Herein, different conditions in electrocatalytic water splitting are reviewed and the effects and proposed mechanisms in the three conditions are summarized. Then, a comparison of the reaction process and the effects of the ions in different electrolytes are presented. Finally, the challenges and opportunities associated with direct electrocatalytic natural seawater splitting and the perspective are presented to promote the progress of hydrogen production by water splitting.

Advances in Understanding the Electrocatalytic Reconstruction Chemistry of Coordination Compounds

Coordination compounds including mainstream metal-organic frameworks and Prussian blue analogues receive extensive researches when they directly serve as electrocatalysts. Their reconstruction phenomena, that are closely associated with actual contributions and intrinsic catalytic mechanisms, are expected to be well summarized. Here, the recent advances in understanding reconstruction chemistry of coordination compounds are reviewed, including their main classifications and structural properties, reconstruction phenomena in electrocatalysis (e.g., oxygen/hydrogen evolution reaction, CO₂ reduction), influence factors of reconstruction parameters (e.g., reconstruction rate and reconstruction degree), and reconstruction-performance correlation. It is outlined that the reconstruction processes are influenced by electronic structure of coordination compounds, pH and temperature of testing solution, and applied potentials. The characterization techniques reflecting the evolution information before and after catalysis are also introduced for reconstruction-related mechanistic study. Finally, some challenges and outlooks on reconstruction investigations of coordination compounds are proposed, and the necessity of studying and understanding of these themes under actual working conditions of devices is highlighted.

Zeolitic imidazolate frameworks as intrinsic light harvesting and charge separation materials for photocatalysis

Zeolitic imidazolate frameworks (ZIFs) are a subclass of metal organic frameworks that have attracted considerable attention in the past years and have found many applications including heterogeneous catalysis due to their highly ordered porous structure, large surface area, and structural flexibility. However, ZIFs are largely utilized as simple hosts or passive media for dispersing other catalytically active species, resembling the roles of zeolites in catalysis. In contrast, our recent findings show that ZIFs not only have broad absorption across the UV-visible and near IR spectral region but also have an exceptionally long-lived excited charge separated state, suggesting that ZIFs may be used as intrinsic light harvesting and photocatalytic materials rather than as inert hosts. This Perspective will focus on the recent progress on the fundamental studies of the intrinsic light absorption, charge separation, and photocatalytic properties of ZIFs and will discuss the outlook for future development.

Designing MOF Nanoarchitectures for Electrochemical Water Splitting

Electrochemical water splitting has attracted significant attention as a key pathway for the development of renewable energy systems. Fabricating efficient electrocatalysts for these processes is intensely desired to reduce their overpotentials and facilitate practical applications. Recently, metal-organic framework (MOF) nanoarchitectures featuring ultrahigh surface areas, tunable nanostructures, and excellent porosities have emerged as promising materials for the development of highly active catalysts for electrochemical water splitting. Herein, the most pivotal advances in recent research on engineering MOF nanoarchitectures for efficient electrochemical water splitting are presented. First, the design of catalytic centers for MOF-based/derived electrocatalysts is summarized and compared from the aspects of chemical composition optimization and structural functionalization at the atomic and molecular levels. Subsequently, the fast-growing breakthroughs in catalytic activities, identification of highly active sites, and fundamental mechanisms are thoroughly discussed. Finally, a comprehensive commentary on the current primary challenges and future perspectives in water splitting and its commercialization for hydrogen production is provided. Hereby, new insights into the synthetic principles and electrocatalysis for designing MOF nanoarchitectures for the practical utilization of water splitting are offered, thus further promoting their future prosperity for a wide range of applications.

Evolution of metal organic frameworks as electrocatalysts for water oxidation

The development of metal organic framework based water oxidation catalysts is discussed here in connection with various design strategies.