Comparison of Two Acid Hydrotropes for Sustainable Fractionation of Birch Wood

Bioactive lignin from maleic acid hydrotropic fractionation: Revealing the structural-bioactivity relationship

Lignin possesses diverse bioactivities due to its unique physicochemical structure. This study investigates the structural-bioactivity relationships of lignin derived from maleic acid hydrotropic fractionation (MAHF) of two types of herbaceous biomass. The results indicated that lignin with higher phenolic hydroxyl (-OH) content (up to 2.0 mmol/g) and carboxyl (-COOH) groups (up to 0.89 mmol/g) exhibited significantly enhanced antioxidant activity. The highest antioxidant of MAHF lignin (MAHL) reached 98 % for scavenging DPPH (2,2-diphenyl-1-(2,4,6-trinitrophenyl)hydrazyl) at 0.56 mg/mL. Antibacterial tests revealed that MAHLs demonstrated inhibition rates of 66 % against E. coli and 54 % against S. aureus at 10 mg/mL. MAHLs at 1 mg/mL concentration blocked >98 % of UV radiation. Furthermore, the study demonstrated that lignin with higher phenolic hydroxyl (-OH), carboxyl (-COOH), and syringyl (S) units and conjugated double bonds exhibit enhanced bioactive properties. Lignin with lower Mw and PDI also tends to possess good bioactivities. The findings from the study can facilitate the application of lignin as an efficient, cost-effective, and renewable biopolymer additive in various industries.

Equilibrium Moisture Mediated Esterification Reaction to Achieve Over 100% Lignocellulosic Nanofibrils Yield

Lignocellulosic nanofibrils (LCNFs) isolation is recognized as an efficient strategy for maximizing biomass utilization. Nevertheless, achieving a 100% yield presents a formidable challenge. Here, an esterification strategy mediated by the equilibrium moisture in biomass is proposed for LCNFs preparation without the use of catalysts, resulting in a yield exceeding 100%. Different from anhydrous chemical thermomechanical pulp (CTMP0%), the presence of moisture (moisture content of 7 wt%, denoted as CTMP7%) introduces a notably distinct process for the pretreatment of CTMP, comprising the initial disintegration and the post-esterification steps. The maleic acid, generated through maleic anhydride (MA) hydrolysis, degrades the recalcitrant lignin-carbohydrate complex (LCC) structures, resulting in esterified CTMP7% (E-CTMP7%). The highly grafted esters compensate for the mass loss resulting from the partial removal of hydrolyzed lignin and hemicellulose, ensuring a high yield. Following microfluidization, favorable LCNF7% with a high yield (114.4 ± 3.0%) and a high charge content (1.74 ± 0.09 mmol g-1) can be easily produced, surpassing most previous records for LCNFs. Additionally, LCNF7% presented highly processability for filaments, films, and 3D honeycomb structures preparation. These findings provide valuable insights and guidance for achieving a high yield in the isolation of LCNFs from biomass through the mediation of equilibrium moisture.

The Enhancement Origin of Antioxidant Property of Carboxylated Lignin Isolated from Herbaceous Biomass Using the Maleic Acid Hydrotropic Fractionation

Lignin is endowed with antioxidant activity due to its diverse chemical structure. It is necessary to explore the relationship between antioxidant activity and the chemical structure of the lignin to develop its high-value utilization. Herein, we employed maleic acid (MA) as a hydrotropic agent to preferably isolate the lignin from distinct herbaceous sources (wheat straw and switchgrass) under atmospheric pressure conditions. The resultant acid hydrotropic lignin (AHL) isolated from wheat straw exhibited high radical scavenging rates, up to 98% toward DPPH and 94% toward ABTS. Further investigations indicated that during the MA hydrotropic fractionation (MAHF) process, lignin was carboxylated by MA at γ-OH of the side-chain, providing additional antioxidant activity from the carboxy group. It was also found that the radical scavenging rate of AHL has a positive correlation with carboxyl, phenolic hydroxyl contents, and the S-G (syringyl-guaiacyl) ratio, which could be realized by increasing the MAHF severity. Overall, this work underlies the enhancement origin of the antioxidant property of lignin, which will facilitate its application in biological fields as an efficient, cheap, and renewable antioxidant additive.

Comprehensive insights of pretreatment strategies on the structures and bioactivities variation of lignin-carbohydrate complexes

Introduction: Due to its unique structural features and bioactivities, the lignin-carbohydrate complex (LCC) displays great potential in vast industrial applications. However, the elucidation of how various pretreatment methods affect the structure and bioactivities remains unaddressed. Method: The three pretreatment methods were systematically studied on the variations of structures and bioactivities, and the Gramineae plant, i.e., wheat straw, was adopted in this study. The structures and bioactivities variation caused by different pretreatments were studied in detail. Result and Discussion: The results showed that compared to physical or chemical pretreatments, biological pretreatment was the most effective approach in improving the bioactivities of LCC. The LCC from biological pretreatment (enzymatic hydrolysis, ELCC4) had more functional groups while the lower weight-average molecular weight (Mw) and polydispersity index (PDI) were well-endowed. The highest antioxidant abilities against ABTS and DPPH of ELCC4 were high up to 95% and 84%, respectively. Furthermore, ELCC4 also showed the best ultraviolet (UV)-blocking rate of 96%, which was increased by 6% and 2% compared to LCC8 (physical pretreatment) and LLCC4 (chemical pretreatment). This work prospectively boosts the understanding of pretreatment strategies on the structures and bioactivities variation of LCC and facilitates its utilization as sustainable and biologically active materials in various fields.

High-Lignin-Containing Cellulose Nanofibrils from Date Palm Waste Produced by Hydrothermal Treatment in the Presence of Maleic Acid

Lignin-containing cellulose nanofibrils (LCNFs) have attracted great attention because the presence of lignin brought additional merits to cellulose nanofibrils including hydrophobicity, ultraviolet (UV)-shielding capacity, and reduced water sensitivity. In the present work, LCNFs with lignin content up to 21 wt % were prepared with a high yield exceeding 70 wt %, from neat date palm waste, by a hydrothermal treatment (HTT) at 120-150 °C in the presence of 20-30 wt % maleic acid, followed by high-pressure homogenization. The chemical composition, degree of polymerization, morphology, and colloidal and rheological properties of the LCNFs were investigated to understand how the HTT in the presence of MA affected the properties of the resulting LCNFs. Nanopapers prepared from the LCNF suspensions exhibited mechanical properties lower than those from lignin-free CNF-based nanopapers, yet with decreased hydrophilicity. A mechanism explaining how the HTT in the presence of MA facilitated the disintegration of the biomass into nanoscale material was proposed. Overall, the present work demonstrated a feasible and scalable approach for the sustainable production of LCNF suspensions from neat agricultural residues, with a high yield and a high lignin content, without any need to perform a preliminary partial delignification.

Freeze-thaw assisted maleic acid pretreatment of eucalyptus to prepare cellulose nanocrystals and degraded lignin

A green and effective method is proposed for the pretreatment of eucalyptus by freeze-thaw assisted maleic acid tactic, wherein the effects of freeze-thaw, maleic acid concentration, reaction time, and temperature on the fractionation were examined. Results showed that under optimal conditions (60% maleic acid, 120 °C, and 2 h), a remarkable removal of 74.5% lignin and 95.2% hemicellulose was achieved after freeze-thaw treatment. The resulting cellulose-rich solid residues were further processed with maleic acid to prepare cellulose nanocrystals, which displayed uniform sized rod-like structures and high crystallinity (62.51%). Moreover, maleic acid pretreatment resulted in lignin with low molecular weight (2110-2530) and excellent homogeneity (PDI ≤ 1.86), while maintaining a relatively intact structure. The lignin had high β-O-4 aryl ether bond contents (≥77.5%) and abundant phenolic hydroxyl contents (2.33-3.63 mmol/g). Overall, the process exhibits notable benefits in effectively separating lignocellulose for high valorization.

Integrated enzyme hydrolysis assisted cellulose nanofibril (CNF) fabrication: A sustainable approach to paper mill sludge (PMS) management

The landfilling of paper mill sludge (PMS) has been restricted or even banned in many countries due to the raised concern about greenhouse gas (GHG) emissions and contamination of the soil and water, calling for a sustainable PMS management approach. The potential valorization of PMS to nanomaterials combined with traditional biorefinery was examined in this work. Three types of PMS-derived cellulose nanofibrils (CNFs) were prepared and evaluated: enzymatically assisted CNF (AU: with in-house produced enzyme and CT: with commercial enzyme), mechanically pretreated CNF (BT), and chemically pretreated CNF by TEMPO oxidation (TEMPO). It was found that enzyme-assisted mechanical fibrillation-derived CNFs had a comparable average diameter (27.9 nm for AU and 22.7 nm for CT) with that produced from mechanical pretreatment (26.5 nm for BT) and TEMPO oxidation pretreatment (20.0 nm for TEMPO), and they showed the best drainage properties among the three types of CNF. The CNFs resulting from enzymatic pretreatment reduced 15% of energy consumption compared to the mechanical method and had better thermostability than TEMPO oxidation method. In addition, the on-site produced enzyme showed similar performance to the commercial enzymes towards the CNF properties. These findings provide new insights into a promising integrated strategy in engineering CNF from PMS with on-site enzyme production as a novel and sustainable approach for PMS management and valorization.

Application and prospect of organic acid pretreatment in lignocellulosic biomass separation: A review

As a clean and efficient method of lignocellulosic biomass separation, organic acid pretreatment has attracted extensive research. Hemicellulose or lignin is selectively isolated and the cellulose structure is preserved. Effective fractionation of lignocellulosic biomass is achieved. The separation characteristics of hemicellulose or lignin by different organic acids were summarized. The organic acids of hemicellulose were separated into hydrogen ionized, autocatalytic and α-hydroxy acids according to the separation mechanism. The separation of lignin depends on the dissolution mechanism and spatial effect of organic acids. In addition, the challenges and prospects of organic acid pretreatment were analyzed. The separation of hemicellulose and enzymatic hydrolysis of cellulose were significantly affected by the polycondensation of lignin, which is effectively inhibited by the addition of green additives such as ketones or alcohols. Lignin separation was improved by developing a deep eutectic solvent treatment based on organic acid pretreatment. This work provides support for efficient cleaning of carbohydrate polymers and lignin to promote global carbon neutrality.

Kinetics of Lignin Separation during the Atmospheric Fractionation of Bagasse with p-Toluenesulfonic Acid

As a green and efficient component separation technology, organic acid pretreatment has been widely studied in biomass refining. In particular, the efficient separation of lignin by p-toluenesulfonic acid (p-TsOH) pretreatment has been achieved. In this study, the mechanism of the atmospheric separation of bagasse lignin with p-TsOH was investigated. The separation kinetics of lignin was analyzed. A non-simple linear relationship was found between the separation yield of lignin and the concentration of p-TsOH, the temperature and the stirring speed. The shrinking nucleus model for the separation of lignin was established based on the introduction of mass transfer and diffusion factors. A general model of the total delignification rate was obtained. The results showed that the process of lignin separation occurred into two phases, i.e., a fast stage and a slow stage. The results provide a theoretical basis for the efficient separation of lignin by p-TsOH pretreatment.

Polystyrene sulfonate is effective for enhancing biomass enzymatic saccharification under green liquor pretreatment in bioenergy poplar

BACKGROUND

Water-soluble lignin (particularly lignosulfonate, LS) has been well documented for its significance on enzymatic saccharification of lignocellulose, though the promotion mechanism has not been fully understood. Much attention has been paid to natural lignin or its derivatives. The disadvantage of using natural lignin-based polymers as promoting agents lies in the difficulty in tailor-incorporating functional groups due to their complex 3D structures. To further improve our understanding on the promotion mechanism of water-soluble lignin in the bioconversion of lignocellulose and to pursue better alternatives with different skeleton structures other than natural lignin, herein we reported a synthetic soluble linear aromatic polymer, sodium polystyrene sulfonate (PSS), to mimic LS for enhancing the efficiency of enzymatic saccharification.

RESULTS

The role of PSS in enzymatic saccharification of pure cellulose and green liquor-pretreated poplar (GL-P) was explored by analyzing substrate enzymatic digestibility (SED) under different addition dosages and various pH media, along with LS for comparison. At the cellulase loading of 13.3 FPU/g-glucan, the glucose yield of GL-P increased from 53% for the control to 81.5% with PSS addition of 0.1 g/g-substrate. It outperformed LS with the addition of 0.2 g/g-substrate by 6.3%. In the pH range from 4.5 to 6, PSS showed a positive effect on lignocellulose saccharification with the optimum pH at 4.8, where the most pronounced SED of GL-P was achieved. The underlying mechanism was unveiled by measuring zeta potential and using Quartz Crystal Microbalance (QCM) and Multi-parametric Surface Plasmon Resonance (MP-SPR). The results confirmed that the complexes of cellulase and PSS were conjugated and the negatively supercharged complexes reduced non-productive binding effectively along with the improved saccharification efficiency. The thickness of PSS required to block the binding sites of cellulase film was less than half of that of LS, and the PSS adlayer on cellulase film is also more hydrated and with a much lower shear modulus than LS adlayer.

CONCLUSIONS

PSS as LS analogue is effective for enhancing the biomass enzymatic saccharification of GL-pretreated poplar. PSS exhibited a severer inhibition on the enzymatic saccharification of pure cellulose, while a more positive effect on bioconversion of lignocellulose (GL-P) than LS. In addition, a much lower dosage is required by PSS. The dynamic enzymatic hydrolysis indicated PSS could prolong the processive activity of cellulase. The valid data stemmed from QCM and SPR expressed that PSS bound to cellulases and the as-formed complexes reduced the non-productive adsorption of cellulase onto substrate lignin more efficiently than LS due to its flexible skeleton and highly hydrated structure. Therefore, PSS is a promising alternative promoting agent for lignocellulose saccharification. From another perspective, the synthetic lignin mimics with controllable structures enable us to reach an in-depth understanding of the promotion mechanism of soluble lignins on enzymatic saccharification.

Acid Hydrotropic Fractionation of Lignocelluloses for Sustainable Biorefinery: Advantages, Opportunities, and Research Needs

This Minireview provides a comprehensive discussion on the potential of using acid hydrotropes for sustainably fractionating lignocelluloses for biorefinery applications. Acid hydrotropes are a class of acids that have hydrotrope properties toward lignin, which helps to solubilize lignin in aqueous systems. With the capability of cleaving ether and ester bonds and even lignin-carbohydrate complex (LCC) linkages, these acid hydrotropes can therefore isolate lignin embedded in the plant biomass cell wall and subsequently solubilize the isolated lignin in aqueous systems. Performances of two acid hydrotropes, that is, an aromatic sulfonic acid [p-toluenesulfonic acid (p-TsOH)] and a dicarboxylic acid [maleic acid (MA)], in terms of delignification and dissolution of hemicelluloses, and reducing lignin condensation, were evaluated and compared. The advantages of lignin esterification by MA for producing cellulosic sugars through enzymatic hydrolysis and lignin-containing cellulose nanofibrils (LCNFs) through mechanical fibrillation from the fractionated water insoluble solids (WIS), and for obtaining less condensed lignin with light color, were demonstrated. The excellent enzymatic digestibility of maleic acid hydrotropic fractionation WISs was also demonstrated by comparing with WISs from other fractionation processes. The recyclability and reusability of acid hydrotropes were also reviewed. Finally, perspectives on future research needs to address key technical issues for commercialization were also provided.

Enhancement of the antioxidant abilities of lignin and lignin-carbohydrate complex from wheat straw by moderate depolymerization via LiCl/DMSO solvent catalysis

A facile and environmentally-friendly strategy for increasing antioxidant activity is a crucial issue for value-added lignin and lignin-carbohydrate complex (LCC) as alternative antioxidants. However, the antioxidant activities of lignin and LCC by the traditional solid-liquid extraction (SLE) methods were restricted by the relatively lower solubility induced from high molecular weight (Mw), and the less functional groups including, phenolic hydroxyl and carboxyl. To improve the antioxidantion of lignin and LCC, lithium chloride/dimethyl sulfoxide (LiCl/DMSO) solvent fractionation (LDSF) was conducted to increase the functional groups and reduce Mw, in which LiCl/DMSO acted triple roles as solvent, acid, and metal chloride catalyst for the depolymerization reaction synchronously. The β-O-4' linkages were cleaved to release the phenolic hydroxyl, resulting in decreasing Mw; the hydroxyl of the side-chain of lignin was oxidized into carboxyl. Thus, the lignin (LD-RL) and LCC (LD-LCC) samples from LDSF had a higher syringyl (S)/guaiacyl (G) ratio, phenolic hydroxyl, and carboxyl contents, but less Mw than control groups from SLE. Consequently, they presented more excellent scavenging rates toward DPPH and ABTS radicals, up to 90%. This work provided panoramic perspectives and basics of the green and convenient approach to isolate and modify lignin and LCC for great antioxidantion with LDSF.

Towards sustainable production and utilization of plant-biomass-based nanomaterials: a review and analysis of recent developments

Plant-biomass-based nanomaterials have attracted great interest recently for their potential to replace petroleum-sourced polymeric materials for sustained economic development. However, challenges associated with sustainable production of lignocellulosic nanoscale polymeric materials (NPMs) need to be addressed. Producing materials from lignocellulosic biomass is a value-added proposition compared with fuel-centric approach. This report focuses on recent progress made in understanding NPMs-specifically lignin nanoparticles (LNPs) and cellulosic nanomaterials (CNMs)-and their sustainable production. Special attention is focused on understanding key issues in nano-level deconstruction of cell walls and utilization of key properties of the resultant NPMs to allow flexibility in production to promote sustainability. Specifically, suitable processes for producing LNPs and their potential for scaled-up production, along with the resultant LNP properties and prospective applications, are discussed. In the case of CNMs, terminologies such as cellulose nanocrystals (CNCs) and cellulose nanofibrils (CNFs) used in the literature are examined. The term cellulose nano-whiskers (CNWs) is used here to describe a class of CNMs that has a morphology similar to CNCs but without specifying its crystallinity, because most applications of CNCs do not need its crystalline characteristic. Additionally, progress in enzymatic processing and drying of NPMs is also summarized. Finally, the report provides some perspective of future research that is likely to result in commercialization of plant-based NPMs.

Lignin Based Activated Carbon Using H3PO4 Activation

Activated carbon (AC) with a very high surface area of over 2000 m²/g was produced from low sulfur acid hydrotropic lignin (AHL) from poplar wood using H₃PO₄ at a moderate temperature of 450 °C (AHL-AC6). ACs with similar surface areas were also obtained under the same activation condition from commercial hardwood alkali lignin and lignosulfonate. Initial evaluation of AC performance was carried out using nitrogen adsorption-desorption and dye adsorption. AHL-AC6 exhibited the best specific surface area and dye adsorption performance. Furthermore, the adsorption results of congo red (CR) and methylene blue (MB) showed AHL-AC6 had greater adsorption capacity than those reported in literature. The dye adsorption data fit to the Langmuir model well. The fitting parameter suggests the adsorption is nearly strong and near irreversible, especially for MB. The present study for the first time provided a procedure for producing AC from lignin with Brunauer–Emmett–Teller (BET) surface area >2000 m²/g using low cost and low environmental impact H₃PO₄ at moderate temperatures.

Residual lignin in cellulose nanofibrils enhances the interfacial stabilization of Pickering emulsions

Lignocellulose nanofibrils (LCNF) were used to prepare oil-in-water Pickering emulsions and to assess the role residual lignin in interfacial stabilization. Two LCNF fractions of similar morphology (length ∼700 nm and width ∼8 nm) and structure (polymorphism and crystallinity) were obtained by microfluidization of fibers obtained by hydrothermal treatment of wood with a recyclable organic acid. The LCNF with higher residual lignin was less hydrophilic and, correspondingly, performed better as Pickering stabilizer, producing emulsions of smaller droplet size and higher resistance to creaming. Long-term emulsion stabilization (over 40 days) was achieved with LCNF at concentrations as low as 0.24 (w/v)% based on emulsion volume. We conclude that LCNF-stabilized Pickering emulsions can be finely tuned by varying the residual lignin content, providing a rationale for LCNF selection according to lignin type and concentration as variables affecting stabilization. Complementary considerations include the possible benefits of the residual lignin in LCNF, including antioxidant and UV absorption properties.

Pilot-Scale Production of Cellulosic Nanowhiskers With Similar Morphology to Cellulose Nanocrystals

This study describes a class of cellulosic nanomaterials, cellulosic nanowhiskers (CNWs), and demonstrates scaled-up production with acid recovery using less expensive equipment made of common stainless steel rather than glass-lined steel. CNWs produced using concentrated maleic acid (MA) hydrolysis followed by mechanical fibrillation have morphology similar to MA-produced cellulose nanocrystals (CNCs) and sulfuric-acid-produced CNCs (S-CNCs) but differ in crystallinity. Applications of CNWs as a substitute for CNCs for which morphology and surface charge, rather than crystallinity, are the pertinent characteristics are presented. The tested CNW suspensions have a wider viscosity range of 0.001 to 1000 Pa.s over a variety of shear rates of 0.01 to 1000 1/s compared to S-CNCs of 0.001 to 0.1 Pa.s and are better suited for applications such as rheology modification and 3D printing. This study proposes CNWs as a less expensive and sustainable replacement for CNCs in applications that do not require crystalline properties.