Kinetic characterization of the interaction of biotinylated human interleukin 5 with an Fc chimera of its receptor alpha subunit and development of an ELISA screening assay using real-time interaction biosensor analysis

Carbodiimide-mediated immobilization of acidic biomolecules on reversed-charge zwitterionic sensor chip surfaces

The carbodiimide-mediated amine coupling of protein ligands to sensor chips coated with anionic polycarboxylate hydrogels, such as carboxymethyl dextran, is the predominant covalent immobilization procedure utilized in optical biosensors, namely surface plasmon resonance (SPR) biosensors. Usually, electrostatic interactions at a slightly acidic pH and low ionic strength are employed to efficiently accumulate neutral and basic ligands on the chip surface, which are then covalently coupled by surface-bound active N-hydroxysuccinimide (NHS) esters. Unfortunately, this approach is not suitable for acidic proteins or other ligands with low isoelectric points (IEPs), such as nucleic acids, because the charge density of the polycarboxylates is greatly reduced at acidic pH or because electrostatic attraction cannot be achieved. To overcome these drawbacks, we have established a charge-reversal approach that allows the preconcentration of acidic proteins above their IEPs. A precisely controlled amount of tertiary amines is applied to reverse the previous anionic surface charge while maintaining carbodiimide compatibility with future protein immobilization. The mechanism of this reversed-charge immobilization approach was demonstrated employing protein A as a model protein and using attenuated total reflectance Fourier transform infrared spectroscopy, dynamic contact angle measurements, colorimetric quantification, and SPR analysis to characterize surface derivatization. Furthermore, even though it had previously proven impossible to preconcentrate DNA electrostatically and to covalently couple it to polyanionic chip surfaces, we demonstrated that our approach allowed DNA to be preconcentrated and immobilized in good yields. Graphical abstract Principle of the covalent immobilization of acidic ligands on reversed-charge zwitterionic sensor chip surfaces.

Exploring biomolecular recognition using optical biosensors

Understanding the basic forces that determine molecular recognition helps to elucidate mechanisms of biological processes and facilitates discovery of innovative biotechnological methods and materials for therapeutics, diagnostics, and separation science. The ability to measure interaction properties of biological macromolecules quantitatively across a wide range of affinity, size, and purity is a growing need of studies aimed at characterizing biomolecular interactions and the structural elements that drive them. Optical biosensors have provided an increasingly impactful technology for such biomolecular interaction analyses. These biosensors record the binding and dissociation of macromolecules in real time by transducing the accumulation of mass of an analyte molecule at the sensor surface coated with ligand molecule into an optical signal. Interactions of analytes and ligands can be analyzed at a microscale and without the need to label either interactant. Sensors enable the detection of bimolecular interaction as well as multimolecular assembly. Most notably, the method is quantitative and kinetic, enabling determination of both steady-state and dynamic parameters of interaction. This article describes the basic methodology of optical biosensors and presents several examples of its use to investigate such biomolecular systems as cytokine growth factor-receptor recognition, coagulation factor assembly, and virus-cell docking.

Instrumental biosensors: new perspectives for the analysis of biomolecular interactions

The use of instrumental biosensors in basic research to measure biomolecular interactions in real time is increasing exponentially. Applications include protein-protein, protein-peptide, DNA-protein, DNA-DNA, and lipid-protein interactions. Such techniques have been applied to, for example, antibody-antigen, receptor-ligand, signal transduction, and nuclear receptor studies. This review outlines the principles of two of the most commonly used instruments and highlights specific operating parameters that will assist in optimising experimental design, data generation, and analysis.

A scintillation proximity assay for human interleukin-5 (hIL-5) high-affinity binding in insect cells coexpressing hIL-5 receptor alpha and beta subunits

The high-affinity receptor for human interleukin-5 (hIL-5) is composed of alpha and beta subunits. A baculovirus expression system was established in Sf9 cells capable of expressing hIL-5 receptor alpha and beta subunits simultaneously. By using wheat germ agglutinin (WGA)-coated scintillation proximity assay (SPA) beads to capture 125I-labeled hIL-5-bound Sf9 cells, a SPA was developed and used to measure hIL-5 high-affinity binding. The hIL-5 receptors expressed in the Sf9 cells represented a single class of high-affinity binding sites with a dissociation constant (Kd) of 0. 24 nM and a density of 2.95 x 10(5) sites/cell. This is the first study in which the high-affinity Kd value similar to that for hIL-5 binding to human eosinophils was achieved using a recombinant expression system. The SPA compared favorably with the filter binding assay with regard to various binding parameters. We also found that several lectins, when coated on SPA beads, were even more effective than WGA-coated SPA beads for capturing the insect cells. We conclude that the baculovirus expression system was highly efficient in producing the high-affinity hIL-5 receptors and that the SPA was a simple and sensitive assay that could be readily adapted into a high-throughput screening format. The SPA described here could be a prototype for binding assays for other multimeric receptors.