Photonic Crystal Hydrogel Enhanced Plasmonic Staining for Multiplexed Protein Analysis

Vertical flow immunoassay for multiplex mycotoxins based on photonic nitrocellulose and SERS nanotags

Here, we report a SERS based VFA using PNC as a sensing substrate for highly sensitive multiplex mycotoxins detection. The PNC was fabricated by filtration-based self-assembled monodisperse SiO2 NPs on a filter membrane as a template, and the obtained PNC had an ordered complementary inverse opal structure. In parallel, three kinds of Raman dyes encoding Au@NBAAg, Au@4-MBAAg and Au@DNTBAg SERS nanotags were synthesized for the detection of OTA, AFB1 and ZON. In the immunoassay, because of the slow-photon effect of the PNC substrate, which facilitates the light coupling with SERS nanotags, the SERS signal was highly enhanced. The LODs of 8.2, 13.7 and 47.6 fg mL-1 were achieved for simultaneous detection of OTA, AFB1 and ZON, respectively, which were lower than the tolerable cutoff values recommended by the EC. Therefore, this proposed PNC based SERS VFA is expected to be a powerful method for multiplex mycotoxins detection.

Fabrication of SERS composite substrates using Ag nanotriangles-modified SiO2 photonic crystal and the application of malachite green detection

A novel surface-enhanced Raman scattering (SERS) composite substrates on the basis of Ag triangular nanoplates(Ag TNPs)-modified SiO2 photonic crystals (PC) is fabricated and applied to the SERS detection of malachite green (MG). It consists of uniformly arranged Ag TNP@SiO2, a new PC. Notably, Ag TNP are uniformly aligned on the SiO2 surface, forming a three-dimensional high-density hotspot nanostructure. With the tip "hot spots" of Ag TNPs, Bragg diffraction of SiO2 and coupling enhancement between Ag TNPs and SiO2, the SERS enhancement of this composite substrates was multiplied. The effect on the SERS of Ag TNP@SiO2 composite substrate was systematically optimized by tuning Ag TNP size, size of SiO2 microspheres, coverage of Ag TNPs on SiO2 and fabrication method of Ag TNPs and PC. Moreover, the uniform of SERS composite substrates and Raman signal was dramatically increased by the method of vertical deposition. Eventually, the SERS composite substrates were employed in MG detection. Its broad detection range of 1 pM-1 μM and low limit of detection (LOD) of 0.49 pM indicated acceptable sensitivity and repeatability. This work illustrates the promising applicability in food safety analysis based on SERS composite substrates composed by Ag TNP@SiO2 with numerous SERS enhancements and excellent stability.

Label-Free Multiplexed Microfluidic Analysis of Protein Interactions Based on Photonic Crystal Surface Mode Imaging

High-throughput protein assays are crucial for modern diagnostics, drug discovery, proteomics, and other fields of biology and medicine. It allows simultaneous detection of hundreds of analytes and miniaturization of both fabrication and analytical procedures. Photonic crystal surface mode (PC SM) imaging is an effective alternative to surface plasmon resonance (SPR) imaging used in conventional gold-coated, label-free biosensors. PC SM imaging is advantageous as a quick, label-free, and reproducible technique for multiplexed analysis of biomolecular interactions. PC SM sensors are characterized by a longer signal propagation at the cost of a lower spatial resolution, which makes them more sensitive than classical SPR imaging sensors. We describe an approach for designing label-free protein biosensing assays employing PC SM imaging in the microfluidic mode. Label-free, real-time detection of PC SM imaging biosensors using two-dimensional imaging of binding events has been designed to study arrays of model proteins (antibodies, immunoglobulin G-binding proteins, serum proteins, and DNA repair proteins) at 96 points prepared by automated spotting. The data prove feasibility of simultaneous PC SM imaging of multiple protein interactions. The results pave the way to further develop PC SM imaging as an advanced label-free microfluidic assay for the multiplexed detection of protein interactions.

Label-Free Surface-Enhanced Raman Spectroscopic Analysis of Proteins: Advances and Applications

Surface-enhanced Raman spectroscopy (SERS) is powerful for structural characterization of biomolecules under physiological condition. Owing to its high sensitivity and selectivity, SERS is useful for probing intrinsic structural information of proteins and is attracting increasing attention in biophysics, bioanalytical chemistry, and biomedicine. This review starts with a brief introduction of SERS theories and SERS methodology of protein structural characterization. SERS-active materials, related synthetic approaches, and strategies for protein-material assemblies are outlined and discussed, followed by detailed discussion of SERS spectroscopy of proteins with and without cofactors. Recent applications and advances of protein SERS in biomarker detection, cell analysis, and pathogen discrimination are then highlighted, and the spectral reproducibility and limitations are critically discussed. The review ends with a conclusion and a discussion of current challenges and perspectives of promising directions.

Towards Multiplexed and Multimodal Biosensor Platforms in Real-Time Monitoring of Metabolic Disorders

Metabolic syndrome (MS) is a cluster of conditions that increases the probability of heart disease, stroke, and diabetes, and is very common worldwide. While the exact cause of MS has yet to be understood, there is evidence indicating the relationship between MS and the dysregulation of the immune system. The resultant biomarkers that are expressed in the process are gaining relevance in the early detection of related MS. However, sensing only a single analyte has its limitations because one analyte can be involved with various conditions. Thus, for MS, which generally results from the co-existence of multiple complications, a multi-analyte sensing platform is necessary for precise diagnosis. In this review, we summarize various types of biomarkers related to MS and the non-invasively accessible biofluids that are available for sensing. Then two types of widely used sensing platform, the electrochemical and optical, are discussed in terms of multimodal biosensing, figure-of-merit (FOM), sensitivity, and specificity for early diagnosis of MS. This provides a thorough insight into the current status of the available platforms and how the electrochemical and optical modalities can complement each other for a more reliable sensing platform for MS.

One-step assembly of barcoded planar microparticles for efficient readout of multiplexed immunoassay

Barcoded planar microparticles are suitable for developing cost-efficient multiplexed assays, but the robustness and efficiency of the readout process still needs improvement. Here, we designed a one-step microparticle assembling chip that produces efficient and accurate multiplex immunoassay readout results. Our design was also compatible with injection molding for mass production.

Advances in droplet microfluidics for SERS and Raman analysis

Raman spectroscopy can realize qualitative and quantitative characterization, and surface-enhanced Raman spectroscopy (SERS) can further enhance its detection sensitivity. In combination with droplet microfluidics, some significant but insurmountable limitations of SERS and Raman spectroscopy can be overcome to some extent, thus improving their detection capability and extending their application. During the past decade, these systems have constantly developed and demonstrated a great potential in more applications, but there is no new review systematically summarizing the droplet microfluidics-based Raman and SERS analysis system since the first related review was published in 2011. Thus, there is a great need for a new review to summarize the advances. In this review, we focus on droplet microfluidics-based Raman and SERS analysis, and summarize two mainstream research directions on this topic up to now. The one is SERS or Raman detection in the moving droplet microreactors, including analysis of molecules, single cells and chemical reaction processes. The other one is SERS active microparticle fabrication via microfluidic droplet templates covering polymer matrix and photonic crystal microparticles. We also comment on the advantages, disadvantage and correlation resolution of droplet microfluidics for SERS or Raman. Finally, we summarize these systems and illustrate our perspectives for future research directions in this field.

Highly Ordered, Plasmonic Enhanced Inverse Opal Photonic Crystal for Ultrasensitive Detection of Staphylococcal Enterotoxin B

Although there is considerable interest in self-assembly of ordered, porous "inverse opal" structures for optical, electronic, and chemical applications, uncontrolled defect formation limits the usefulness of such materials. Herein, we develop a highly ordered and plasmonic enhanced sensing inverse opal photonic crystal (IOPC) material. The co-assembly of the colloidal template with the matrix material avoids the need for liquid penetration into the preassembled colloidal crystals and minimizes the associated rupture and inhomogeneity of the resulting IOPC. Au nanoparticles (Au NPs) not only act as a "bridge" between recognition elements (aptamers) and IOPCs, but also can amplify optical signals. Furthermore, the enhancement mechanism of Au NPs is simulated by COMSOL. During the detection process, the optical signal of the sensing Au-Apt IOPC responds to the Staphylococcal enterotoxin B with a concentration ranging from 10^-2 to 10³ pg mL^-1, and the limit of detection is 2.820 fg mL^-1. Spiked real sample detection indicates that the as-proposed method possessed good accuracy. The sensing Au-Apt IOPC provides an extensive biosensor platform to detect a variety of toxic and harmful substances through replacing the aptamer by other recognition elements, such as antibodies or receptors.

A Novel Multiplex Mycotoxin Surface-Enhanced Raman Spectroscopy Immunoassay Using Functional Gold Nanotags on a Silica Photonic Crystal Microsphere Biochip

A novel multiplex mycotoxin surface-enhanced Raman spectroscopy (SERS) immunoassay was established for the first time on different artificial antigen-modified silica photonic crystal microspheres (SPCMs), which can be integrated into a biochip array to achieve multiplex detection using corresponding antibody-functionalized gold nanoparticles (AuNPs) as the SERS nanotag. The unique optical structure of SPCMs is helpful to find the detection spots easily, accommodate a large amount of probe molecules, and enhance the Raman signal intensity. Such enhancement was confirmed by the simulation result, showing the electric field enhancing effect in SPCMs with AuNPs being 7 times. A competitive SERS immunoassay was established using antigen-modified SPCMs and mycotoxins to compete for binding antibody-functionalized SERS nanotags, displaying broad linear detection ranges of 0.001-0.1 ng/mL for aflatoxin B₁ (AFB₁), 0.01-10 ng/mL for ochratoxin A (OTA), and 0.001-0.1 ng/mL for zearalenone (ZEN) and low detection limits of 0.82 pg/mL for AFB₁, 1.43 pg/mL for OTA, and 1.00 pg/mL for ZEN. In the spiked cereal samples, recovery rates of the method were measured in the range of 70.35-118.04% for the three mycotoxins, which was in agreement with that of the traditional enzyme-linked immunosorbent assay method. The SERS immunoassay for mycotoxin detection also showed high specificity and good repeatability and reproducibility. The new microsphere-based SERS immunoassay biochip only requires a one-step reaction and overcomes the disadvantages of fluorescence and chemiluminescence background signals. The work paves the way for further developing SERS-based microsphere suspension arrays for new targets.

Au nanobowtie on a SiO2 microsphere for optoplasmonic trapping

The combination of photonic and plasmonic elements with complementary optical properties has stimulated the development of optoplasmonic hybrid systems, in which photonic and plasmonic elements can interact synergistically, breaking through the limitations of traditional structures. In this paper, a new optoplasmonic tweezer is theoretically proposed by using the Au nanobowtie and SiO₂ microsphere. The finite-difference time-domain simulation is used to study the influence of the size of the SiO₂ microsphere and the SiO₂ hemisphere in polydimethylsiloxane on the optical potential well. The simulation results show that the electric field intensity of the structure is increased by 6 times compared with the Au nanobowtie structure, and the gradient force and the trapping potential are also significantly improved.

Bottom-Up Assembled Photonic Crystals for Structure-Enabled Label-Free Sensing

Photonic crystals (PhCs) display photonic stop bands (PSBs) and at the edges of these PSBs transport light with reduced velocity, enabling the PhCs to confine and manipulate incident light with enhanced light-matter interaction. Intense research has been devoted to leveraging the optical properties of PhCs for the development of optical sensors for bioassays, diagnosis, and environmental monitoring. These applications have furthermore benefited from the inherently large surface area of PhCs, giving rise to high analyte adsorption and the wide range of options for structural variations of the PhCs leading to enhanced light-matter interaction. Here, we focus on bottom-up assembled PhCs and review the significant advances that have been made in their use as label-free sensors. We describe their potential for point-of-care devices and in the review include their structural design, constituent materials, fabrication strategy, and sensing working principles. We thereby classify them according to five sensing principles: sensing of refractive index variations, sensing by lattice spacing variations, enhanced fluorescence spectroscopy, surface-enhanced Raman spectroscopy, and configuration transitions.

Photonic crystal based biosensors: Emerging inverse opals for biomarker detection

Photonic crystal (PC)-based inverse opal (IO) arrays are one of the substrates for label-free sensing mechanism. IO-based materials with their advanced and ordered three-dimensional microporous structures have recently found attractive optical sensor and biological applications in the detection of biomolecules like proteins, DNA, viruses, etc. The unique optical and structural properties of IO materials can simplify the improvements in non-destructive optical study capabilities for point of care testing (POCT) used within a wide variety of biosensor research. In this review, which is an interdisciplinary investigation among nanotechnology, biology, chemistry and medical sciences, the recent fabrication methodologies and the main challenges regarding the application of (inverse opals) IOs in terms of their bio-sensing capability are summarized.

•

The recent main challenges regarding the application of inverse opals (IOs) in the detection of biomolecules are reviewed.

•

Sensing mechanisms of biomolecules including glucose, proteins, DNA, viruses were summarized.

•

IO materials with their ordered 3D microporous structures have found attractive optical biosensor applications.

Precipitation-based colorimetric multiplex immunoassay in hydrogel particles

Despite a growing demand for more accessible diagnostic technologies, current methods struggle to simultaneously detect multiple analytes with acceptable sensitivity and portability. Colorimetric assays have been widely used due to their simplicity of signal readout, but the lack of multiplexibility has been a perpetual constraint. Meanwhile, particle-based assays offer multiplex detection by assigning an identity code to each analyte, but they often require lab-based equipment unsuitable for portable diagnostics. Here, by merging the two approaches, this paper reports a colorimetric multiplex immunoassay based on hydrogel microparticles that achieves the best of both worlds. The low-cost portable multiplex assay demonstrates sensitivities as high as and dynamic ranges greater than the lab-based enzyme-linked immunosorbent assay (ELISA). These critical advances are made possible by local precipitation and amplification of insoluble colour dyes inside the hydrogel networks. For the first time, enzymatic accumulation of colour dyes in hydrogel particles is reported and the kinetics of colour development is characterized in this work. By taking advantage of the colour signals in the visible spectrum, the hydrogel microparticles were imaged and analysed using low-cost portable devices. The colorimetric multiplex immunoassay was used to successfully detect three target biomarkers of preeclampsia and validated clinically using healthy and patient-derived plasma samples.

Surface enhanced Raman scattering artificial nose for high dimensionality fingerprinting

Label-free surface-enhanced Raman spectroscopy (SERS) can interrogate systems by directly fingerprinting their components' unique physicochemical properties. In complex biological systems however, this can yield highly overlapping spectra that hinder sample identification. Here, we present an artificial-nose inspired SERS fingerprinting approach where spectral data is obtained as a function of sensor surface chemical functionality. Supported by molecular dynamics modeling, we show that mildly selective self-assembled monolayers can influence the strength and configuration in which analytes interact with plasmonic surfaces, diversifying the resulting SERS fingerprints. Since each sensor generates a modulated signature, the implicit value of increasing the dimensionality of datasets is shown using cell lysates for all possible combinations of up to 9 fingerprints. Reliable improvements in mean discriminatory accuracy towards 100% are achieved with each additional surface functionality. This arrayed label-free platform illustrates the wide-ranging potential of high-dimensionality artificial-nose based sensing systems for more reliable assessment of complex biological matrices.

Tuning Physical Crosslinks in Hybrid Hydrogels for Network Structure Analysis and Mechanical Reinforcement

Hydrogels with high mechanical strength are needed for a variety of industrial applications. Here, a series of hydrogels was prepared by introducing hybrid particles as hydrophobic association points to toughen the hydrogels. These toughened hydrogels were able to transfer an external mechanical force via the reorganization of the crosslinking networks. They exhibited an extraordinary mechanical performance, which was the result of the coordination between hydrophobic segments and hybrid particles. Herein, the connection between the dissipated energy of the inner distribution structure (on a small scale) and the mechanical properties (on a large scale) was conducted. Specifically, we inspected hydrogels of latex particles (LPs) with different chain lengths (C4, C12, C18) and studied their inner structural parameters, namely, the relationship between the density and molecular weight of crosslinking points to the mechanical strength and energy dissipation. Favorable traits of the hydrogels included compact internal structures that were basically free from defects and external structures with puncture resistance, high toughness, etc. Based on the experimental results that agreed with the theoretical results, this study provides a profound understanding of the internal structure of hydrogels, and it offers a new idea for the design of high-strength hybrid hydrogels.

Recent advances in merging photonic crystals and plasmonics for bioanalytical applications

Photonic crystals (PhCs) and plasmonic nanostructures offer the unprecedented capability to control the interaction of light and biomolecules at the nanoscale. Based on PhC and plasmonic phenomena, a variety of analytical techniques have been demonstrated and successfully implemented in many fields, such as biological sciences, clinical diagnosis, drug discovery, and environmental monitoring. During the past decades, PhC and plasmonic technologies have progressed in parallel with their pros and cons. The merging of photonic crystals with plasmonics will significantly improve biosensor performances and enlarge the linear detection range of analytical targets. Here, we review the state-of-the-art biosensors that combine PhC and plasmonic nanomaterials for quantitative analysis. The optical mechanisms of PhCs, plasmonic crystals, and metal nanoparticles (NPs) are presented, along with their integration and potential applications. By explaining the optical coupling of photonic crystals and plasmonics, the review manifests how PhC-plasmonic hybrid biosensors can achieve the advantages, including high sensitivity, low cost, and short assay time as well. The review also discusses the challenges and future opportunities in this fascinating field.

Label-free SERS in biological and biomedical applications: Recent progress, current challenges and opportunities

To achieve an insightful look within biomolecular processes on the cellular level, the development of diseases as well as the reliable detection of metabolites and pathogens, a modern analytical tool is needed that is highly sensitive, molecular-specific and exhibits fast detection. Surface-enhanced Raman spectroscopy (SERS) is known to meet these requirements and, within this review article, the recent progress of label-free SERS in biological and biomedical applications is summarized and discussed. This includes the detection of biomolecules such as metabolites, nucleic acids and proteins. Further, the characterization and identification of microorganisms has been achieved by label-free SERS-based approaches. Eukaryotic cells can be characterized by SERS in order to gain information about the outer cell wall or to detect intracellular molecules and metabolites. The potential of SERS for medically relevant detection schemes is emphasized by the label-free detection of tissue, the investigation of body fluids as well as applications for therapeutic and illicit drug monitoring. The review article is concluded with an evaluation of the recent progress and current challenges in order to highlight the direction of label-free SERS in the future.

Single-Step Fabrication of High-Throughput Surface-Enhanced Raman Scattering Substrates

The combination of surface-enhanced Raman scattering (SERS) with high-throughput screening (HTS) has significant importance for highly sensitive and massive workload assays. Although fabrication of HTS-SERS substrates can be achieved by several methods, the high cost as well as large-equipment dependence limit their applications. Here, we report a simple method to fabricate HTS-SERS substrates within one-step process. The HTS-SERS substrate is fabricated by simply UV-irradiating a fluoroalkylsilane (FAS)-modified liquid-repellent TiO₂ surface in AgNO₃ solution through a photomask. Owing to the photocatalytic nature of TiO₂, the UV irradiation simultaneously triggers the degradation of the attached FAS and the generation of liquid-adhesive Ag nanoparticles (NPs) on exposed area. A HTS-SERS substrate could be directly obtained after UV irradiation. The deposited Ag NPs evidently enhance Raman signals, and the significant difference between the wettability of exposed area and masked area enables fast formation of high-throughput liquid droplet arrays through a simple dragging solution process. The fabrication method is applicable to various substrate materials, to introduce additional functionalities. The photocatalytic activity of TiO₂ also allows us to photobleach the residual analyte and Ag NPs after detection to recycle substrate. This single-step method is a highly promising candidate for the fabrication of HTS-SERS substrates.

Antibacterial Structural Color Hydrogels

Structural color hydrogels with lasting survivability are important for many applications, but they still lack anti-biodegradation capability. Thus, we herein present novel antibacterial structural color hydrogels by simply integrating silver nanoparticles (AgNPs) in situ into the hydrogel materials. Because the integrated AgNPs possessed wide and excellent antibacterial abilities, the structural color hydrogels could prevent bacterial adhesion, avoid hydrogel damage, and maintain their vivid structural colors during their application and storage. It was demonstrated that the AgNP-tagged poly(N-isopropylacrylamide) structural color hydrogels could retain their original thermal-responsive color transition even when the AgNP-free hydrogels were degraded by bacteria and that the AgNP-integrated self-healing structural color protein hydrogels could save their self-repairing property instead of being degraded by bacteria. These features indicated that the antibacterial structural color hydrogels could be amenable to a variety of practical biomedical applications.

Breath-Taking Patterns: Discontinuous Hydrophilic Regions for Photonic Crystal Beads Assembly and Patterns Revisualization

Surfaces patterned with hydrophilic and hydrophobic regions provide robust and versatile means for investigating the wetting behaviors of liquids, surface properties analysis, and producing patterned arrays. However, the fabrication of integral and uniform arrays onto these open systems remains a challenge, thus restricting them from being used in practical applications. Here, we present a simple yet powerful approach for the fabrication of water droplet arrays and the assembly of photonic crystal bead arrays based on hydrophilic-hydrophobic patterned substrates. Various integral arrays are simply prepared in a high-quality output with a low cost, large scale, and uniform size control. By simply taking a breath, which brings moisture to the substrate surface, complex hydrophilic-hydrophobic outlined images can be revisualized in the discontinuous hydrophilic regions. Integration of hydrogel photonic crystal bead arrays into the "breath-taking" process results in breath-responsive photonic crystal beads, which can change their colors upon a mild exhalation. This state-of-the-art technology not only provides an effective methodology for the preparation of patterned arrays but also demonstrates intriguing applications in information storage and biochemical sensors.

Ultrasensitive Detection of Protein with Wide Linear Dynamic Range Based on Core-Shell SERS Nanotags and Photonic Crystal Beads

Detection of proteins in a wide concentration range from fg mL^-1 to sub mg mL^-1 is a challenge in the high throughput analysis of precision medicine. Herein, we proposed a biosensor consisting of core-shell surface-enhanced Raman scattering (SERS) nanotags as labels and photonic crystal beads (PCBs) as carriers for ultrasensitive detection of proteins. In practice, Raman dyes (RDs) were embedded in the interface of gold core and silver shell in the bimetal nanoparticles to form SERS nanotags. It was found that the sensitivity was significantly improved due to the enhanced Raman signal by the coupling of the core-shell structure and linear dynamic range (LDR) was extended owing to the high surface to volume ratio of PCBs as well. In addition, we also demonstrated that the biosensor exhibited fine stability and low background, which has great application potential in the detection of protein biomarkers.

Discrimination of Nosiheptide Sources with Plasmonic Filters

Bacteria identification plays a vital role in the field of clinical diagnosis, food industry, and environmental monitoring, which is in great demand of point of care detection methods. In this paper, in order to discriminate the source of nosiheptide product, a plasmonic filter was fabricated to filtrate, capture and identify Streptomycete spores with Surface enhanced Raman Scattering (SERS). Since the plasmonic filter was derived from self-assembled photonic crystal coated with silver, the plasmonic "hot spots" on the filter surface was distributed evenly in a fare good density and the SERS enhancement factor was 7.49 × 10⁷. With this filter, a stain- and PCR-free detection was realized with only 5 μL sample solution and 5 min in a manner of "filtration and measure". Comparison to traditional Gram stain method and silver-plated nylon filter membrane, the plasmonic filter showed good sensitivity and efficiency in the discrimination of nosiheptide prepared with chemical and biological methods. It is anticipated that this simple SERS detection method with plasmonic filter has promising potentials in food safety, environmental, or clinical applications.

Multiplex bioassays encoded by photonic crystal beads and SERS nanotags

Multiplex bioassays have drawn more and more attention for the development of novel analytical techniques. Herein, we used photonic crystal (PC) and surface enhanced Raman scattering (SERS) as two encoding elements in different modes for the dual encoding of multiplex bioassays. In practice, PC beads and SERS nanotags act as carriers and labels, respectively, for the multiplex detection of antigens in a sandwich format. Except for the amplified capacity by two encoding modes, we also demonstrated that fine stability, low background and high sensitivity were realized for the quantitative analysis of multiple analytes, which holds great promise in biomedical applications like protein biomarker analysis.

Optofluidic sensing from inkjet-printed droplets: the enormous enhancement by evaporation-induced spontaneous flow on photonic crystal biosilica

Novel transducers for detecting an ultra-small volume of an analyte solution play pivotal roles in many applications such as chemical analysis, environmental protection and biomedical diagnosis. Recent advances in optofluidics offer tremendous opportunities for analyzing miniature amounts of samples with high detection sensitivity. In this work, we demonstrate enormous enhancement factors (106-107) of the detection limit for optofluidic analysis from inkjet-printed droplets by evaporation-induced spontaneous flow on photonic crystal biosilica when compared with conventional surface-enhanced Raman scattering (SERS) sensing using the pipette dispensing technology. Our computational fluid dynamics simulation has shown a strong recirculation flow inside the 100 picoliter droplet during the evaporation process due to the thermal Marangoni effect. The combination of the evaporation-induced spontaneous flow in micron-sized droplets and the highly hydrophilic photonic crystal biosilica is capable of providing a strong convection flow to combat the reverse diffusion force, resulting in a higher concentration of the analyte molecules at the diatom surface. In the meanwhile, high density hot-spots provided by the strongly coupled plasmonic nanoparticles with photonic crystal biosilica under a 1.5 μm laser spot are verified by finite-difference time domain simulation, which is crucial for SERS sensing. Using a drop-on-demand inkjet device to dispense multiple 100 picoliter analyte droplets with pinpoint accuracy, we achieved the single molecule detection of Rhodamine 6G and label-free sensing of 4.5 × 10-17 g trinitrotoluene from only 200 nanoliter solution.

High-Flexibility, High-Toughness Double-Cross-Linked Chitin Hydrogels by Sequential Chemical and Physical Cross-Linkings

High-flexibility, high-toughness double-cross-linked (DC) chitin hydrogels are prepared through a sequential chemical and physical cross-linkings strategy. The incorporation of chemically and physically cross-linked domains imbues the DC chitin hydrogels with relatively high stiffness, high toughness, and toughness recoverability.

Spatially multiplexed dark-field microspectrophotometry for nanoplasmonics

Monitoring the effect of the substrate on the local surface plasmon resonance (LSPR) of metallic nanoparticles is key for deepening our understanding of light-matter interactions at the nanoscale. This coupling gives rise to shifts of the LSPR as well as changes in the scattering pattern shape. The problem requires of high-throughput techniques that present both high spatial and spectral resolution. We present here a technique, referred to as Spatially Multiplexed Micro-Spectrophotometry (SMMS), able to perform polarization-resolved spectral and spatial analysis of the scattered light over large surface areas. The SMMS technique provides three orders of magnitude faster spectroscopic analysis than conventional dark-field microspectrophotometry, with the capability for mapping the spatial distribution of the scattered light intensity with lateral resolution of 40 nm over surface areas of 0.02 mm(2). We show polarization-resolved dark-field spectral analysis of hundreds of gold nanoparticles deposited on a silicon surface. The technique allows determining the effect of the substrate on the LSPR of single nanoparticles and dimers and their scattering patterns. This is applied for rapid discrimination and counting of monomers and dimers of nanoparticles. In addition, the diameter of individual nanoparticles can be rapidly assessed with 1 nm accuracy.