Blending Donors with Different Molecular Weights: An Efficient Strategy to Resolve the Conflict between Coherence Length and Intermixed Phase in Polymer/Nonfullerene Solar Cells

Bias-Switchable Photomultiplication and Photovoltaic Dual-Mode Near-Infrared Organic Photodetector

Photomultiplication-type organic photodetectors (PM-OPDs) provide for signal amplification, ideal for detecting faint light, and simplifying detection systems. However, current designs often suffer from slow response speed and elevated dark current. Conversely, photovoltaic-type organic photodetectors (PV-OPDs) provide fast response and high specific detectivity (D*) but have limited photoresponse. This study presents the synthesis and incorporation of a non-fullerene acceptor, BFDO-4F, into the active layer to introduce trap states for capturing photogenerated electrons. The resulting device exhibits dual-mode characteristic and is bias-switchable between PV and PM-modes. In PV-mode, the OPDs achieve high D* of 1.92 × 10¹2 Jones and a response time of 2.83/4.43 µs. In PM-mode, the OPDs exhibit exceptional external quantum efficiency (EQE) up to 3484% and a D* of up to 1.13 × 10¹2 Jones. An on-chip self-powered module with PV-mode pixels driving a PM-mode pixel is demonstrated, yielding a photocurrent approximately five times higher than the reference device. This approach paves the way for developing multifunctional bias-switchable dual-mode on-chip OPDs, suitable for various applications.

A Dual-Polythiophene Blending Strategy to Reduce the Efficiency-Stability-Cost Gap of Solar Cells

Benefiting from the photovoltaic material innovation and delicate device optimization, high-efficiency solar cells employing polymeric materials are thriving. Reducing the gap of cost, efficiency, and stability is the critical challenge faced by the emerging solar cells such as organics, quantum dots and perovskites. Poly(3-alkylthiophene) demonstrates great potential in organic solar cells and quantum dot solar cells as the active layer or the hole transport layer due to its large scalability, excellent photoelectric performance, and favorable hydrophobicity. The present low efficiency and insufficient stability, restrict its commercial application. In this work, a facile strategy of blending two simple polythiophenes is put forward to manipulate the film microstructure and enhance the device efficiency and thermal stability of solar cells. The introduction of P3PT can improve the power conversion efficiency (PCE) of a benchmark cost-effective blend P3HT:O-IDTBR to 7.41%, and the developed ternary solar cells also exhibit increased thermal stability. More strikingly, the quantum dot solar cells with the dual-polythiophene hole transport layer achieve the highest PCE of 10.51%, which is among the topmost efficiencies for quantum dots/polythiophene solar cells. Together, this work provides an effective route to simultaneously optimize the device efficiency and thermal stability of solar cells.

Selectively Modulating Componential Morphologies of Bulk Heterojunction Organic Solar Cells

Achieving precise control over the nanoscale morphology of bulk heterojunction films presents a significant challenge for the conventional post-treatments employed in organic solar cells (OSCs). In this study, a near-infrared photon-assisted annealing (NPA) strategy is developed for fabricating high-performance OSCs under mild processing conditions. It is revealed a top NIR light illumination, together with the bottom heating, enables the selective tuning of the molecular arrangement and assembly of narrow bandgap acceptors in polymer networks to achieve optimal morphologies, as well as the acceptor-rich top surface of active layers. The derived OSCs exhibit a remarkable power conversion efficiency (PCE) of 19.25%, representing one of the highest PCEs for the reported binary OSCs so far. Moreover, via the NPA strategy, it has succeeded in accessing top-illuminated flexible OSCs using thermolabile polyethylene terephthalate from mineral water bottles, displaying excellent mechanical stabilities. Overall, this work will hold the potential to develop organic solar cells under mild processing with various substrates.

Enhancing the Molecular Order and Vertical Component Distribution of the P3HT/O-IDTBR System during Layer-by-Layer Processing

The molecular order and vertical component distribution are critical to enhance the charge transport in layer-by-layer (LbL) processed active layer. However, the excessive inter-diffusion between donor and acceptor layers during LbL processing irrepressibly reduces their ordered packing. Herein, a novel tactic to optimize the molecular order and vertical morphology of the active layer through suppressing the deep penetration of (5Z,5'Z)-5,5'-((7,7'-(4,4,9,9-tetraoctyl-4,9-dihydro-s-indaceno[1,2-b:5,6 -b']dithiophene-2,7-diyl)bis(benzo[c][1,2,5]thiadiazole-7,4-diyl))bis(methanylylidene)) bis(3-ethyl-2-thioxothiazolidin-4-one) (O-IDTBR) to poly(3-hexylthiophene) (P3HT) film during LbL processing is proposed. This is enabled by inducing the formation of P3HT nanofibers through ultraviolet (UV) irradiation and solution aging. During the LbL processing, these nanofibers with high crystallinity reduce the damage of O-IDTBR solution to P3HT film and restrict the penetration of O-IDTBR into P3HT matrix. As a result, the P3HT nanofibers are preserved and the degree of vertical phase separation is enlarged in the LbL-processed film. Meanwhile, the molecular order of both components is enhanced. The resulting morphology that featured as intertwined P3HT nanofibers/O-IDTBR network efficiently promotes charge transport and extraction, boosting the power conversion efficiency (PCE) of the devices from 6.70 ± 0.12% to 7.71 ± 0.10%.

Anthradithiophene (ADT)-Based Polymerized Non-Fullerene Acceptors for All-Polymer Solar Cells

Realizing efficient all-polymer solar cell (APSC) acceptors typically involves increased building block synthetic complexity, hence potentially unscalable syntheses and/or prohibitive costs. Here we report the synthesis, characterization, and implementation in APSCs of three new polymer acceptors P1-P3 using a scalable donor fragment, bis(2-octyldodecyl)anthra[1,2-b : 5,6-b']dithiophene-4,10-dicarboxylate (ADT) co-polymerized with the high-efficiency acceptor units, NDI, Y6, and IDIC. All three copolymers have comparable photophysics to known polymers; however, APSCs fabricated by blending P1, P2 and P3 with donor polymers PM5 and PM6 exhibit modest power conversion efficiencies (PCEs), with the champion P2-based APSC achieving PCE=5.64 %. Detailed morphological and microstructural analysis by AFM and GIWAXS reveal a non-optimal APSC active layer morphology, which suppresses charge transport. Despite the modest efficiencies, these APSCs demonstrate the feasibility of using ADT as a scalable and inexpensive electron rich/donor building block for APSCs.

Unraveling the Photovoltaic, Mechanical, and Microstructural Properties and Their Correlations in Simple Poly(3-pentylthiophene) Solar Cells

The power conversion efficiency of polythiophene organic solar cells is constantly refreshed. Despite the renewed device efficiency, very few efforts have been devoted to understanding how the type of electron acceptor alters the photovoltaic and mechanical properties of these low-cost solar cells. Herein, we conduct a thorough investigation of photovoltaic and mechanical characteristics of a simple yet less explored polythiophene, namely poly(3-pentylthiophene) (P3PT), in three different types of organic solar cells, where ZY-4Cl, PC₇₁ BM, and N2200 are employed as three representative acceptors, respectively. Compared with the reference P3HT-based solar cells, P3PT-based devices all perform more efficiently. Particularly, the P3PT:ZY-4Cl blend exhibits the highest efficiency (nearly 10%) among the six combinations and outperforms the prior top-performance system P3HT:ZY-4Cl. Furthermore, the blend films based on N2200 exhibit a high crack-onset strain of ∼38% on average, which is approximately 15 and 17 times higher than those of ZY-4Cl and PC₇₁ BM, respectively. The microstructural origins for the above difference are well elucidated by detailed grazing incidence X-ray scattering and microscopy analysis. This work not only underlines the potential of P3PT in prolific solar cell research but also demonstrates the superior tensile properties of polythiophene-based all-polymer blends for the preparation of stretchable solar cells. This article is protected by copyright. All rights reserved.

Two Compatible Acceptors as an Alloy Model with a Halogen-Free Solvent for Efficient Ternary Polymer Solar Cells

A ternary strategy of halogen-free solvent processing can open up a promising pathway for the preparation of polymer solar cells (PSCs) on a large scale and can effectively improve the power conversion efficiency with an appropriate third component. Herein, the green solvent o-xylene (o-XY) is used as the main solvent, and the non-fullerene acceptor Y6-DT-4F as the third component is introduced into the PBB-F:IT-4F binary system to broaden the spectral absorption and optimize the morphology to achieve efficient PSCs. The third component, Y6-DT-4F, is compatible with IT-4F and can form an "alloy acceptor", which can synergistically optimize the photon capture, carrier transport, and collection capabilities of the ternary device. Meanwhile, Y6-DT-4F has strong crystallinity, so when introduced into the binary system as the third component can enhance the crystallization, which is conducive to the charge transport. Consequently, the optimal ternary system based on PBB-F:IT-4F:Y6-DT-4F achieved an efficiency of 15.24%, which is higher than that of the binary device based on PBB-F:IT-4F (13.39%).

Recent Advances of Film–Forming Kinetics in Organic Solar Cells

Solution–processed organic solar cells (OSC) have been explored widely due to their low cost and convenience, and impressive power conversion efficiencies (PCEs) which have surpassed 18%. In particular, the optimization of film morphology, including the phase separation structure and crystallinity degree of donor and acceptor domains, is crucially important to the improvement in PCE. Considering that the film morphology optimization of many blends can be achieved by regulating the film–forming process, it is necessary to take note of the employment of solvents and additives used during film processing, as well as the film–forming conditions. Herein, we summarize the recent investigations about thin films and expect to give some guidance for its prospective progress. The different film morphologies are discussed in detail to reveal the relationship between the morphology and device performance. Then, the principle of morphology regulating is concluded with. Finally, a future controlling of the film morphology and development is briefly outlined, which may provide some guidance for further optimizing the device performance.