PTFE-coated non-stick cookware and toxicity concerns: a perspective

Recycling of diaper wastes for a triboelectric nanogenerator-based weather station

Escalating concerns over waste management and the need for sustainable energy have prompted innovative solutions at the nexus of resource recycling and self-powered applications. This study presents a novel approach to recycling super-absorbing polymer (SAP) gels from waste diapers and discarded baking sheets to fabricate a diaper waste-based triboelectric nanogenerator (DW-TENG). The DW-TENG, resembling a maraca, demonstrated superior electrical performance with a voltage output of 110 V, a current of 9 μA, and a power of 259.15 μW. It was successfully integrated into a self-powered weather station for real-time monitoring of wind speed, humidity, and temperature. This research underscores the dual benefits of waste management and energy generation, representing a promising step toward a circular and sustainable future.

Early-life exposure to per- and polyfluoroalkyl substances: Analysis of levels, health risk and binding abilities to transport proteins

Per- and polyfluoroalkyl substances (PFAS) can pass through the placenta and adversely affect fetal development. However, there is a lack of comparison of legacy and emerging PFAS levels among different biosamples in pregnant women and their offspring. This study, based on the Shanghai Maternal-Child Pairs Cohort, analyzed the concentrations of 16 PFAS in the maternal serum, cord serum, and breast milk samples from 1,076 mother-child pairs. The placental and breastfeeding transfer efficiencies of PFAS were determined in maternal-cord and maternal-milk pairs, respectively. The binding affinities of PFAS to five transporters were simulated using molecular docking. The results suggested that PFAS were frequently detected in different biosamples. The median concentration of perfluorooctane sulfonate (PFOS) was the highest at 8.85 ng/mL, followed by perfluorooctanoic acid (PFOA) at 7.13 ng/mL and 6:2 chlorinated polyfluorinated ether sulfonate at 5.59 ng/mL in maternal serum. The median concentrations of PFOA were highest in cord serum (4.23 ng/mL) and breast milk (1.08 ng/mL). PFAS demonstrated higher placental than breastfeeding transfer efficiencies. The transfer efficiencies and the binding affinities of most PFAS to proteins exhibited alkyl chain length-dependent patterns. Furthermore, we comprehensively assessed the estimated daily intakes (EDIs) of PFAS in breastfeeding infants of different age groups and used the hazard quotient (HQ) to characterize the potential health risk. EDIs decreased with infant age, and PFOS had higher HQs than PFOA. These findings highlight the significance of considering PFAS exposure, transfer mechanism, and health risks resulting from breast milk intake in early life.

Beyond the food on your plate: Investigating sources of microplastic contamination in home kitchens

Given that a substantial amount of time is spent in kitchens preparing food, the kitchen equipment used may be relevant in determining the composition and amount of microplastics ending up on our dinner plate. While previous research has predominantly focused on foodstuffs as a source of microplastics, we emphasise that micro- and nanoplastics are ubiquitous and likely originate from diverse sources. To address the existing knowledge gap regarding additional sources contributing to microplastics on our dinner plates, this review investigates various kitchen processes, utensils and equipment (excluding single-use items and foodstuffs) to get a better understanding of potential microplastic sources within a home kitchen. Conducting a narrative literature review using terms related to kitchenware and kitchen-affiliated equipment and processes, this study underscores that the selection of preparation tools, storage, serving, cooking, and cleaning procedures in our kitchens may have a significant impact on microplastic exposure. Mechanical, physical, and chemical processes occurring during food preparation contribute to the release of microplastic particles, challenging the assumption that exposure to microplastics in food is solely tied to food products or packaging. This review highlights diverse sources of microplastics in home kitchens, posing concerns for food safety and human health.

Influence of heating temperature and time on mechanical-degradation, microstructures and corrosion performances of Teflon/granite coated aluminum alloys used for non-stick cookware

This study explores the functional characteristics (erosion, corrosion, mechanical damage, and microstructural features) of non-stick cookware made from aluminum alloys. Typically coated with polytetrafluoroethylene (PTFE-Teflon) or ceramic for non-stick properties, we conducted a systematic investigation using corrosion, abrasion, and mechanical tests on six types of cookware from different manufacturers (Manuf-1-6). The cookware was heated at various temperatures [Room temperature (RT), 100, 175, 250, & 350 °C] and times (45 & 120 min). Tests included Taber wear, Adhesive Pull-off, hot & RT corrosion, and surface roughness measurements. Characterization involved optical microscopy, scanning electron microscope (SEM) with electron backscattered diffraction (EBSD), and x-ray diffraction (XRD). Ceramic-coated cookware from Manuf-4 demonstrated superior mechanical strength, wear, and corrosion resistance due to refined microstructures. Manuf-1's PTFE-coated cookware also performed well. Optimal results were observed when heating below 250 °C for up to 45 min. Prolonged heating and temperatures beyond 250 °C adversely affected internal structures of all cookware. Thus, it is advisable to use Al-based non-stick cookware below 250 °C for a maximum of 45 min.

Microplastic and PTFE contamination of food from cookware

Microplastics are a prolific environmental contaminant that have been evidenced in human tissues. Human uptake of microplastic occurs via inhalation of airborne fibres and ingestion of microplastic-contaminated foods and beverages. Plastic and PTFE-coated cookware and food contact materials may release micro- and nanoplastics into food during food preparation. In this study, the extent to which non-plastic, new plastic and old plastic cookware releases microplastics into prepared food is investigated. Jelly is used as a food simulant, undergoing a series of processing steps including heating, cooling, mixing, slicing and storage to replicate food preparation steps undertaken in home kitchens. Using non-plastic cookware did not introduce microplastics to the food simulant. Conversely, using new and old plastic cookware resulted in significant increases in microplastic contamination. Microplastics comprised PTFE, polyethylene and polypropylene particulates and fibrous particles, ranging 13-318 μm. Assuming a meal was prepared daily per the prescribed methodology, new and old plastic cookware may be contributing 2409-4964 microplastics per annum into homecooked food. The health implications of ingesting microplastics remains unclear.

PFAS in Nigeria: Identifying data gaps that hinder assessments of ecotoxicological and human health impacts

This review examines the extensive use and environmental consequences of Per- and Polyfluoroalkyl Substances (PFAS) on a global scale, specifically emphasizing their potential impact in Nigeria. Recognized for their resistance to water and oil, PFAS are under increased scrutiny for their persistent nature and possible ecotoxicological risks. Here, we consolidate existing knowledge on the ecological and human health effects of PFAS in Nigeria, focusing on their neurological effects and the risks they pose to immune system health. We seek to balance the advantages of PFAS with their potential ecological and health hazards, thereby enhancing understanding of PFAS management in Nigeria and advocating for more effective policy interventions and the creation of safer alternatives. The review concludes with several recommendations: strengthening regulatory frameworks, intensifying research into the ecological and health impacts of PFAS, developing new methodologies and longitudinal studies, fostering collaborative efforts for PFAS management, and promoting public awareness and education to support sustainable environmental practices and healthier communities in Nigeria.

Beyond Conventional Density Functional Theory: Advanced Quantum Dynamical Methods for Understanding Degradation of Per- and Polyfluoroalkyl Substances

Computational chemistry methods, such as density functional theory (DFT), have now become more common in environmental research, particularly for simulating the degradation of per- and polyfluoroalkyl substances (PFAS). However, the vast majority of PFAS computational studies have focused on conventional DFT approaches that only probe static, time-independent properties of PFAS near stationary points on the potential energy surface. To demonstrate the rich mechanistic information that can be obtained from time-dependent quantum dynamics calculations, we highlight recent studies using these advanced techniques for probing PFAS systems. We briefly discuss recent applications ranging from ab initio molecular dynamics to DFT-based metadynamics and real-time time-dependent DFT for probing PFAS degradation in various reactive environments. These quantum dynamical approaches provide critical mechanistic information that cannot be gleaned from conventional DFT calculations. We conclude with a perspective of promising research directions and recommend that these advanced quantum dynamics simulations be more widely used by the environmental research community to directly probe PFAS degradation dynamics and other environmental processes.

A critical review of perfluoroalkyl and polyfluoroalkyl substances (PFAS) landfill disposal in the United States

Landfills manage materials containing per- and polyfluoroalkyl substances (PFAS) from municipal solid waste (MSW) and other waste streams. This manuscript summarizes state and federal initiatives and critically reviews peer-reviewed literature to define best practices for managing these wastes and identify data gaps to guide future research. The objective is to inform stakeholders about waste-derived PFAS disposed of in landfills, PFAS emissions, and the potential for related environmental impacts. Furthermore, this document highlights data gaps and uncertainties concerning the fate of PFAS during landfill disposal. Most studies on this topic measured PFAS in liquid landfill effluent (leachate); comparatively fewer have attempted to estimate PFAS loading in landfills or other effluent streams such as landfill gas (LFG). In all media, the reported total PFAS heavily depends on waste types and the number of PFAS included in the analytical method. Early studies which only measured a small number of PFAS, predominantly perfluoroalkyl acids (PFAAs), likely report a significant underestimation of total PFAS. Major findings include relationships between PFAS effluent and landfill conditions - biodegradable waste increases PFAS transformation and leaching. Based on the results of multiple studies, it is estimated that 84% of PFAS loading to MSW landfills (7.2 T total) remains in the waste mass, while 5% leaves via LFG and 11% via leachate on an annual basis. The environmental impact of landfill-derived PFAS has been well-documented. Additional research is needed on PFAS in landfilled construction and demolition debris, hazardous, and industrial waste in the US.

Binding of Per- and Polyfluoroalkyl Substances (PFAS) to the PPARγ/RXRα-DNA Complex

Nuclear receptors are the fundamental building blocks of gene expression regulation and the focus of many drug targets. While binding to DNA, nuclear receptors act as transcription factors, governing a multitude of functions in the human body. Peroxisome proliferator-activator receptor γ (PPARγ) and the retinoid X receptor α (RXRα) form heterodimers with unique properties and have a primordial role in insulin sensitization. This PPARγ/RXRα heterodimer has been shown to be impacted by per- and polyfluoroalkyl substances (PFAS) and linked to a variety of significant health conditions in humans. Herein, a selection of the most common PFAS (legacy and emerging) was studied utilizing molecular dynamics simulations for PPARγ/RXRα. The local and global structural effects of PFAS binding on the known ligand binding pockets of PPARγ and RXRα as well as the DNA binding domain (DBD) of RXRα were inspected. The binding free energies were predicted computationally and were compared between the different binding pockets. In addition, two electronic structure approaches were utilized to model the interaction of PFAS within the DNA binding domain, density functional theory (DFT) and domain-based pair natural orbital coupled cluster with perturbative triples (DLPNO-CCSD(T)) approaches, with implicit solvation. Residue decomposition and hydrogen-bonding analysis were also performed, detailing the role of prominent residues in molecular recognition. The role of l-carnitine is explored as a potential in vivo remediation strategy for PFAS interaction with the PPARγ/RXRα heterodimer. In this work, it was found that PFAS can bind and act as agonists for all of the investigated pockets. For the first time in the literature, PFAS are postulated to bind to the DNA binding domain in a nonspecific manner. In addition, for the PPARγ ligand binding domain, l-carnitine shows promise in replacing smaller PFAS from the pocket.

Thermal Phase Transition and Rapid Degradation of Forever Chemicals (PFAS) in Spent Media Using Induction Heating

In this study, we have developed an innovative thermal degradation strategy for treating per- and polyfluoroalkyl substance (PFAS)-containing solid materials. Our strategy satisfies three criteria: the ability to achieve near-complete degradation of PFASs within a short timescale, nonselectivity, and low energy cost. In our method, a metallic reactor containing a PFAS-laden sample was subjected to electromagnetic induction that prompted a rapid temperature rise of the reactor via the Joule heating effect. We demonstrated that subjecting PFASs (0.001-12 μmol) to induction heating for a brief duration (e.g., <40 s) resulted in substantial degradation (>90%) of these compounds, including recalcitrant short-chain PFASs and perfluoroalkyl sulfonic acids. This finding prompted us to conduct a detailed study of the thermal phase transitions of PFASs using thermogravimetric analysis and differential scanning calorimetry (DSC). We identified at least two endothermic DSC peaks for anionic, cationic, and zwitterionic PFASs, signifying the melting and evaporation of the melted PFASs. Melting and evaporation points of many PFASs were reported for the first time. Our data suggest that the rate-limiting step in PFAS thermal degradation is linked with phase transitions (e.g., evaporation) occurring on different time scales. When PFASs are rapidly heated to temperatures similar to those produced during induction heating, the evaporation of melted PFAS slows down, allowing for the degradation of the melted PFAS.

The Study Influence Analysis of the Mathematical Model Choice for Describing Polymer Behavior

The article considered the three types of description of the material behavior model: elastic, elastic-plastic, and viscoelastic. The problem is considered in the framework of deformable solid mechanics. The paper considers the possibility of describing modern polymeric and composite materials used as antifriction sliding layers in the viscoelasticity framework. A numerical procedure for finding the coefficients to describe the viscoelastic material behavior using the Prony model has been implemented. Numerical results and experimental data are compared. The model problem of spherical indenter penetration into polymer half-space is realized. The influence of the system discretization on the numerical solution is analyzed. The influence of the polymer behavior description in static and dynamic problem formulations is analyzed.

Endocrine disrupting compounds in the baby's world - A harmful environment to the health of babies

Globally, there has been a significant increase in awareness of the adverse effects of chemicals with known or suspected endocrine-acting properties on human health. Human exposure to endocrine disrupting compounds (EDCs) mainly occurs by ingestion and to some extent by inhalation and dermal uptake. Although it is difficult to assess the full impact of human exposure to EDCs, it is well known that timing of exposure is of importance and therefore infants are more vulnerable to EDCs and are at greater risk compared to adults. In this regard, infant safety and assessment of associations between prenatal exposure to EDCs and growth during infancy and childhood has been received considerable attention in the last years. Hence, the purpose of this review is to provide a current update on the evidence from biomonitoring studies on the exposure of infants to EDCs and a comprehensive view of the uptake, the mechanisms of action and biotransformation in baby/human body. Analytical methods used and concentration levels of EDCs in different biological matrices (e.g., placenta, cord plasma, amniotic fluid, breast milk, urine, and blood of pregnant women) are also discussed. Finally, key issues and recommendations were provided to avoid hazardous exposure to these chemicals, taking into account family and lifestyle factors related to this exposure.

Suspect screening and total oxidizable precursor (TOP) assay as tools for characterization of per- and polyfluoroalkyl substance (PFAS)-contaminated groundwater and treated landfill leachate

Landfill facilities are a major source of release of per- and polyfluoroalkyl substances (PFAS) to the surrounding environment. In this study, landfill leachate treated in a conventional wastewater treatment plant and PFAS-contaminated groundwater were subjected to suspect screening analysis and semi-quantification using total oxidizable precursor (TOP) assay and liquid chromatography coupled to high-resolution mass spectrometry (LC-HRMS). TOP assays yielded expected results for legacy PFAS and their precursors, but showed no discernible evidence of degradation of perfluoroethylcyclohexane sulfonic acid. TOP assays also produced significant evidence of presence of precursors in both treated landfill leachate and groundwater, but the majority of precursors had probably degraded into legacy PFAS after many years in the landfill. Suspect screening identified a total of 28 PF AS, of which six were not included in the targeted method and were identified with confidence level (CL) ≥3. Semi-quantification of these six compounds showed very low concentrations, indicating that they are not as great a concern as the target PFAS.

Degradation of Perfluorooctanoic Acid on Aluminum Oxide Surfaces: New Mechanisms from Ab Initio Molecular Dynamics Simulations

Perfluorooctanoic acid (PFOA) is a part of a large group of anthropogenic, persistent, and bioaccumulative contaminants known as per- and polyfluoroalkyl substances (PFAS) that can be harmful to human health. In this work, we present the first ab initio molecular dynamics (AIMD) study of temperature-dependent degradation dynamics of PFOA on (100) and (110) surfaces of γ-Al₂O₃. Our results show that PFOA degradation does not occur on the pristine (100) surface, even when carried out at high temperatures. However, introducing an oxygen vacancy on the (100) surface facilitates an ultrafast (<100 fs) defluorination of C-F bonds in PFOA. We also examined degradation dynamics on the (110) surface and found that PFOA interacts strongly with Al(III) centers on the surface of γ-Al₂O₃, resulting in a stepwise breaking of C-F, C-C, and C-COO bonds. Most importantly, at the end of the degradation process, strong Al-F bonds are formed on the mineralized γ-Al₂O₃ surface, which prevents further dissociation of fluorine into the surrounding environment. Taken together, our AIMD simulations provide critical reaction mechanisms at a quantum level of detail and highlight the importance of temperature effects, defects, and surface facets for PFOA degradation on reactive surfaces, which have not been systematically explored or analyzed.

Effect of different molding pressures on the properties of glass fiber / molybdenum disulfide / Polytetrafluoroethylene composites

Both glass fiber (GF) and molybdenum disulfide (MoS2) can enhance the comprehensive properties of PTFE (polytetrafluoroethylene)-based composites, however the properties of the composites are significantly influenced by the molding pressure utilized. In this study, GF/MoS2/PTFE composites were produced under varied molding pressures (50–70 MPa), and the composites’ mechanical and tribological properties were evaluated. The results showed that the tribological parameters (such as friction coefficient and volumetric wear rate) and mechanical parameters (such as density, hardness, tensile strength, and elongation at break) varied depending on the molding pressure. When the molding pressure was 50 MPa, the GF/MoS2/PTFE composites displayed their finest mechanical properties. The composite had the best wear resistance with the lowest wear rate of only of 2.135 × 10−6 mm3/Nm at a molding pressure of 60 MPa and the lowest friction coefficient of 0.166 at a molding pressure of 70 MPa. The increased molding pressure that was employed to make the samples, as predicted by SEM analysis, would lead to greater residual stresses inside the specimens, which would ultimately result in cracking and peeling. In the friction test, specimens with a lower forming pressure are more likely to have surface furrows that are deeper and wider, as well as to shed their filler. Due to the increased molding pressure, the depth of furrows and filler shedding on the composite surface are also more apparent.

Fluoroplast Doped by Ag2O Nanoparticles as New Repairing Non-Cytotoxic Antibacterial Coating for Meat Industry

Foodborne infections are an important global health problem due to their high prevalence and potential for severe complications. Bacterial contamination of meat during processing at the enterprise can be a source of foodborne infections. Polymeric coatings with antibacterial properties can be applied to prevent bacterial contamination. A composite coating based on fluoroplast and Ag₂O NPs can serve as such a coating. In present study, we, for the first time, created a composite coating based on fluoroplast and Ag₂O NPs. Using laser ablation in water, we obtained spherical Ag₂O NPs with an average size of 45 nm and a ζ-potential of -32 mV. The resulting Ag₂O NPs at concentrations of 0.001-0.1% were transferred into acetone and mixed with a fluoroplast-based varnish. The developed coating made it possible to completely eliminate damage to a Teflon cutting board. The fluoroplast/Ag₂O NP coating was free of defects and inhomogeneities at the nano level. The fluoroplast/Ag₂O NP composite increased the production of ROS (H₂O₂, OH radical), 8-oxogualnine in DNA in vitro, and long-lived active forms of proteins. The effect depended on the mass fraction of the added Ag₂O NPs. The 0.01-0.1% fluoroplast/NP Ag₂O coating exhibited excellent bacteriostatic and bactericidal properties against both Gram-positive and Gram-negative bacteria but did not affect the viability of eukaryotic cells. The developed PTFE/NP Ag₂O 0.01-0.1% coating can be used to protect cutting boards from bacterial contamination in the meat processing industry.

Raman imaging for the identification of Teflon microplastics and nanoplastics released from non-stick cookware

The characterisation of microplastics is still difficult, and the challenge is even greater for nanoplastics. A possible source of these particles is the scratched surface of a non-stick cooking pot that is mainly coated with Teflon. Herein we employ Raman imaging to scan the surfaces of different non-stick pots and collect spectra as spectrum matrices, akin to a hyperspectral imaging process. We adjust and optimise different algorithms and create a new hybrid algorithm to extract the extremely weak signal of Teflon microplastics and particularly nanoplastics. We use multiple characteristic peaks of Teflon to create several images, and merge them to one, using a logic-based algorithm (i), in order to cross-check them and to increase the signal-noise ratio. To differentiate the varied peak heights towards image merging, an algebra-based algorithm (ii) is developed to process different images with weighting factors. To map the images via the whole set of the spectrum (not just from the individual characteristic peaks), a principal component analysis (PCA)-based algorithm (iii) is employed to orthogonally decode the spectrum matrix to the PCA spectrum and PCA intensity image. To effectively extract the Teflon spectrum information, a new hybrid algorithm is developed to justify the PCA spectra and merge the PCA intensity images with the algebra-based algorithm (PCA/algebra-based algorithm) (iv). Based on these developments and with the help of SEM, we estimate that thousands to millions of Teflon microplastics and nanoplastics might be released during a mimic cooking process. Overall, it is recommended that Raman imaging, along with the signal recognition algorithms, be combined with SEM to characterise and quantify microplastics and nanoplastics.

Composite Coating for the Food Industry Based on Fluoroplast and ZnO-NPs: Physical and Chemical Properties, Antibacterial and Antibiofilm Activity, Cytotoxicity

Bacterial contamination of meat products during its preparation at the enterprise is an important problem for the global food industry. Cutting boards are one of the main sources of infection. In order to solve this problem, the creation of mechanically stable coatings with antibacterial activity is one of the most promising strategies. For such a coating, we developed a composite material based on "liquid" Teflon and zinc oxide nanoparticles (ZnO-NPs). The nanoparticles obtained with laser ablation had a rod-like morphology, an average size of ~60 nm, and a ζ-potential of +30 mV. The polymer composite material was obtained by adding the ZnO-NPs to the polymer matrix at a concentration of 0.001-0.1% using the low-temperature technology developed by the research team. When applying a composite material to a surface with damage, the elimination of defects on a micrometer scale was observed. The effect of the composite material on the generation of reactive oxygen species (H₂O₂, •OH), 8-oxoguanine in DNA in vitro, and long-lived reactive protein species (LRPS) was evaluated. The composite coating increased the generation of all of the studied compounds by 50-200%. The effect depended on the concentration of added ZnO-NPs. The antibacterial and antibiofilm effects of the Teflon/ZnO NP coating against L. monocytogenes, S. aureus, P. aeruginosa, and S. typhimurium, as well as cytotoxicity against the primary culture of mouse fibroblasts, were studied. The conducted microbiological study showed that the fluoroplast/ZnO-NPs coating has a strong bacteriostatic effect against both Gram-positive and Gram-negative bacteria. In addition, the fluoroplast/ZnO-NPs composite material only showed potential cytotoxicity against primary mammalian cell culture at a concentration of 0.1%. Thus, a composite material has been obtained, the use of which may be promising for the creation of antibacterial coatings in the meat processing industry.

Interfacial Surface Properties of Compression Moulded Hydrolysed Polyvinyl Acetate (PVAc) Using Different Release Materials

Understanding the effect surface production has on polymer properties is important in the design of advanced materials. The aim of this study was to determine how the moulding process affected the rate of hydrolysis and the topography, chemistry and physicochemistry of PVAc moulded, hydrolysed surfaces. Three different mould surface materials were used to produce compression moulded PVAc sheets which were treated with aqueous NaOH at a range of concentrations. The Textile moulded sheet demonstrated the best hydrolysis results. The topography of the moulded sheets was transferred to the surfaces and the Kapton release sheet was visually smooth at lower magnification and demonstrated some pitting at higher magnification. The Teflon surface had features transferred from the coated stainless steel at lower magnifications and linear features at higher magnifications and the textile surface had a wrinkled appearance and irregularly spaced peaks. The release sheet used to mould the PVAc surfaces, affected the physicochemical parameters. The Kapton moulded surface demonstrated the most polar attributes and the Teflon surface the most dispersive. It was clear that the selection of the mould material had an influence on surface properties and hydrolysis of moulded PVAc. Such information is important for engineering design in industrial processes.

In Vivo Toxicity and Pharmacokinetics of Polytetrafluoroethylene Microplastics in ICR Mice

The increased use of plastics has led to severe environmental pollution, particularly by microplastics—plastic particles 5 mm or less in diameter. These particles are formed by environmental factors such as weathering and ultraviolet irradiation, thereby making environmental pollution worse. This environmental pollution intensifies human exposure to microplastics via food chains. Despite potential negative effects, few toxicity assessments on microplastics are available. In this study, two sizes of polytetrafluoroethylene (PTFE) microplastics, approximately 5 μm and 10–50 μm, were manufactured and used for single and four-week repeated toxicity and pharmacokinetic studies. Toxicological effects were comprehensively evaluated with clinical signs, body weight, food and water consumption, necropsy findings, and histopathological and clinical-pathological examinations. Blood collected at 15, 30 60, and 120 min after a single administration of microplastics were analyzed by Raman spectroscopy. In the toxicity evaluation of single and four-week repeated oral administration of PTFE microplastics, no toxic changes were observed. Therefore, the lethal dose 50 (LD₅₀) and no-observed-adverse-effect-level (NOAEL) of PTFE microplastics in ICR mice were established as 2000 mg/kg or more. PTFE microplastics were not detected in blood, so pharmacokinetic parameters could not be calculated. This study provides new insight into the long-term toxicity and pharmacokinetics of PTFE microplastics.

Removal of Zwitterionic PFAS by MXenes: Comparisons with Anionic, Nonionic, and PFAS-Specific Resins

Zwitterionic per- and polyfluoroalkyl substances are increasingly detected in aquatic environments. The magnitude of their concentration and increased frequency of detection worldwide raise questions on their presence in drinking water and associated health risk. Scientific knowledge on the identification of treatment technologies to effectively capture such zwitterionic PFAS from contaminated water sources remains largely unknown. In this study, we investigated the application of anionic organic scavenger ion exchange (IX) resins (A860), nonionic IX resins (XAD 4 and XAD 7), PFAS-specific resins (A694 and A592), and Ti₃C₂ MXenes (novel two-dimensional metal carbides) for the removal of select fluorotelomer zwitterionic PFAS from natural waters. The cumulative removal of zwitterionic PFAS at pH ∼ 7 follows the order: Ti₃C₂ MXenes > A694 > A592 > A860 > XAD 4 ∼ XAD 7. Ti₃C₂ MXenes were able to capture >75% of the total influent zwitterionic PFAS and the performance remained consistent in natural and synthetic water. Ti₃C₂ MXenes also exhibited efficient regeneration (>90% recovery) with 0.4 M Na₂SO₃ solution, while the regeneration efficacy of other IX resins generally remained below 20%. Treatment with ∼180 J/cm² UV dosage in the 0.4 M Na₂SO₃ regenerant brine solution yielded >99.9% reduction in the zwitterionic PFAS concentration indicating that UV-sulfite systems exhibit promising potential for the treatment of zwitterionic PFAS concentrates.

Assessment of the migration of perfluorinated compounds and primary aromatic amines from PTFE-coated non-stick cookware marketed in Turkey

Two perfluorinated compounds (PFCs) and 17 different primary aromatic amines (PAAs) were analyzed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) in migrants from 35 cookware samples marketed in Turkey. Among PFCs, only PFOA was identified in 6 samples. Only two components among PAAs, namely aniline (ANL) and 4,4'-methylenedianiline (4,4'-MDA), were detected in analyzed samples. Although aniline was detected in all samples, 4,4'-MDA was detected in only 4 samples. The effects of simulant volume, temperature, and repeated use on the release of these migrants from non-stick cookware were investigated. Three simulant volumes (200, 500, and 1000 mL) were used in migration tests. PFCs and PAAs were identified in simulants at 200 and 500 mL. The increase in the amount of simulant caused a decrease in the concentration of these migrants. The lowest migration values were observed in the samples at consecutive usage cycles. PFCs and PAAs exhibited the highest migration ability with increasing temperature.

Mechanical and wear behaviour of PEEK, PTFE and PU: review and experimental study

Soft polymers such as polyether ether ketone (PEEK), polyurethane (PU) and polytetrafluoroethylene (PTFE) have gained significant research interest in the last few decades owing to their excellent material properties which can be harnessed to meet the demands of various applications such as biomedical implants and accessories, insulation panels to cooking utensils, inner coating material for non-stick cookware etc. In the present study, we provide a comprehensive review on the mechanical and tribological behaviour of PEEK, PU and PTFE polymers. Samples of these materials were also fabricated and the experimentally obtained tensile strength, flexural strength, wear rate and coefficient of frictions were ascertained with values reported in literature. It is highlighted that coefficient of friction of polymers were highly dependent on the surface texture of the polymer’s surface; where an uneven surface exhibited higher coefficient of friction. Perspectives for future progress are also highlighted in this paper.

Unexpected exfoliation and activity of nano poly(tetrafluoroethylene) particles from magnetic stir bars: Discovery and implication

Magnetic stir bars are routinely used by most of researchers in the fields of chemistry, biology and environment etc. An incredible phenomenon, in which the magnetic stirring increased reaction rate by tens of times under ultrasound irradiation, impelled us to explore roles of magnetic stirring. Unexpectedly, the thimbleful nano PTFE particles, from shell of magnetic stir bar, were exfoliated during magnetic stirring and account for ultrahigh tribocatalytic and piezocatalytic activities under ultrasonic irradiation. Reactive oxygen species (ROS), such as hydroxyl radical (OH), superoxide radicals (O₂^-) and singlet oxygen (¹O₂) were generated in the present of PTFE under ultrasound irradiation, which is desired in the pollution control. The newly discovered PTFE activity, against the conventional wisdom that PTFE is inert, which also reminds the researchers that the trace amount of PTFE ground during magnetic stirring may inadvertently botch our experiments and introduce false positive results, especially involving routine magnetic stirring and ultrasound irradiation operation in laboratory. In addition, the safety and inertness of PTFE may require further review in PTFE-based commercial, industrial and biomedical settings.

Life-Related Hazards of Materials Applied to Mg–S Batteries

Nowadays, rechargeable batteries utilizing an S cathode together with an Mg anode are under substantial interest and development. The review is made from the point of view of materials engaged during the development of the Mg–S batteries, their sulfur cathodes, magnesium anodes, electrolyte systems, current collectors, and separators. Simultaneously, various hazards related to the use of such materials are discussed. It was found that the most numerous groups of hazards are posed by the material groups of cathodes and electrolytes. Such hazards vary widely in type and degree of danger and are related to human bodies, aquatic life, flammability of materials, or the release of flammable or toxic gases by the latter.

Prevalence and Implications of Per- and Polyfluoroalkyl Substances (PFAS) in Settled Dust

PURPOSE OF REVIEW

Per- and polyfluoroalkyl substances (PFAS) are a family of more than 7,000 fluorinated compounds. The carbon-fluorine bond of PFAS provides desirable hydrophobic and oleophobic properties and stability that has led to widespread usage in consumer products and industrial applications. The strength of the carbon-fluorine bond also prevents appreciable degradation once released into the environment. Consequently, various household products can release volatile and nonvolatile PFAS into the indoor environment that often concentrate in dust. We discuss the diversity of PFAS in settled dust, emission sources of these chemicals, changes in PFAS profiles in dust over the past century, and the implications for human health.

RECENT FINDINGS

Sources of PFAS found in dust include building materials and furnishings and consumer products used in typical indoor spaces. Daycares and workplaces are emphasized as locations with widespread exposure due to the presence of treated carpeting and industrial-strength cleaners. Comparison and interpretation of findings across studies are complicated by the different ways in which PFAS are screened across studies. We further discuss recent developments in non-targeted software for the comprehensive annotation of PFAS in indoor dust and emphasize the need for comprehensive and harmonized analytical workflows. We highlight the detection and diversity of PFAS in settled dust collected from various indoor spaces, including locations with vulnerable subpopulations. There are opportunities for future research to leverage settled dust as a sentinel environmental matrix to evaluate the link between inhalation and ingestion routes of PFAS exposure to adverse health.

Extravillous trophoblast migration and invasion: Impact of environmental chemicals and pharmaceuticals

During pregnancy, the migration and invasion of extravillous trophoblasts (EVTs) into the maternal uterus is essential for proper development of the placenta and fetus. During the first trimester, EVTs engraft and remodel maternal spiral arteries allowing for efficient blood flow and the transfer of essential nutrients and oxygen to the fetus. Aberrant migration of EVTs leading to either shallow or deep invasion into the uterus has been implicated in a number of gestational pathologies including preeclampsia, fetal growth restriction, and placenta accreta spectrum. The migration and invasion of EVTs is well-coordinated to ensure proper placentation. However, recent data point to the ability of xenobiotics to disrupt EVT migration. These xenobiotics include heavy metals, endocrine disrupting chemicals, and organic contaminants and have often been associated with adverse pregnancy outcomes. In most instances, xenobiotics appear to reduce EVT migration; however, there are select examples of enhanced motility after chemical exposure. In this review, we provide an overview of the 1) current experimental approaches used to evaluate EVT migration and invasion in vitro, 2) ability of environmental chemicals and pharmaceuticals to enhance or retard EVT motility, and 3) signaling pathways responsible for altered EVT migration that are sensitive to disruption by xenobiotics.

Effect of granular activated carbon and other porous materials on thermal decomposition of per- and polyfluoroalkyl substances: Mechanisms and implications for water purification

Thermal treatment is routinely used to reactivate the spent granular activated carbon (GAC) from water purification facilities. It is also an integral part of sewage sludge treatment and municipal solid waste management. This study presents a detailed investigation of the fate of per- and polyfluoroalkyl substances (PFAS) and one PFAS alternative (GenX) in thermal processes, focusing on the effect of GAC. We demonstrate that the thermolysis of perfluoroalkyl carboxylic acids (PFCAs), including perfluorooctanoic acid (PFOA), and GenX can occur at temperatures of 150‒200 °C. Three temperature zones were discovered for PFOA, including a stable and nonvolatile zone (≤90 °C), a phase-transfer and thermal decomposition zone (90‒400 °C), and a fast decomposition zone (≥400 °C). The thermal decomposition began with the homolysis of a C‒C bond next to the carboxyl group of PFCAs, which formed unstable perfluoroalkyl radicals. Dual decomposition pathways seem to exist. The addition of a highly porous adsorbent, such as GAC or a copolymer resin, compressed the intermediate sublimation zone of PFCAs, changed their thermal decomposition pathways, and increased the decomposition rate constant by up to 150-fold at 250 °C. The results indicate that the observed thermal decomposition acceleration was linked to the adsorption of gas-phase PFCA molecules on GAC. The presence of non-activated charcoals/biochars with a low affinity for PFOA did not accelerate its thermal decomposition, suggesting that the π electron-rich, polyaromatic surface of charcoal/GAC played an insignificant role compared to the adsorbent's porosity. Overall, the results indicate that (1) substantial decomposition of PFCAs and GenX during conventional thermal GAC/sludge/waste treatment is very likely, and (2) the presence or addition of GAC or other highly porous materials can accelerate thermal PFAS decomposition and alter decomposition pathways.

Binding of Per- and Polyfluoro-alkyl Substances to Peroxisome Proliferator-Activated Receptor Gamma

Peroxisome proliferator receptor gamma (PPARγ), a type II nuclear receptor, fundamental in the regulation of genes, glucose metabolism, and insulin sensitization has been shown to be impacted by per- and poly-fluoroalkyl substances (PFASs). To consider the influence of PFASs upon PPARγ, the molecular interactions of 27 PFASs have been investigated. Two binding sites have been identified on the PPARγ homodimer structure: the dimer pocket and the ligand binding pocket, the former has never been studied prior. Molecular dynamics calculations were performed to gain insights about PFASs-PPARγ binding and the role of acidic and basic residues. The electrostatic interactions for acidic and basic residues far from the binding site were probed, together with their effect on PPARγ recognition. Short-range electrostatic and van der Waals interactions with nearby residues and their influence on binding energies were investigated. As the negative effects of perfluorooctane sulfonate acid were previously shown to be alleviated by one of its natural ligands, l-carnitine, here, the utility of l-carnitine as a possible inhibitor for other PFASs has been considered. A comparison of the binding patterns of l-carnitine and PFASs provides insights toward mitigation strategies for PFASs.

Optimization of PTFE Coating on PDMS Surfaces for Inhibition of Hydrophobic Molecule Absorption for Increased Optical Detection Sensitivity

Polydimethylsiloxane (PDMS) is a polymer widely used for fabrication and prototyping of microfluidic chips. The porous matrix structure of PDMS allows small hydrophobic molecules including some fluorescent dyes to be readily absorbed to PDMS and results in high fluorescent background signals, thereby significantly decreasing the optical detection sensitivity. This makes it challenging to accurately detect the fluorescent signals from samples using PDMS devices. Here, we have utilized polytetrafluoroethylene (PTFE) to inhibit absorption of hydrophobic small molecules on PDMS. Nile red was used to analyze the effectiveness of the inhibition and the absorbed fluorescence intensities for 3% and 6% PTFE coating (7.7 ± 1.0 and 6.6 ± 0.2) was twofold lower compared to 1% and 2% PTFE coating results (17.2 ± 0.5 and 15.4 ± 0.5). When compared to the control (55.3 ± 1.6), it was sevenfold lower in background fluorescent intensity. Furthermore, we validated the optimized PTFE coating condition using a PDMS bioreactor capable of locally stimulating cells during culture to quantitatively analyze the lipid production using Chlamydomonas reinhardtii CC-125. Three percent PTFE coating was selected as the optimal concentration as there was no significant difference between 3% and 6% PTFE coating. Intracellular lipid contents of the cells were successfully stained with Nile Red inside the bioreactor and 3% PTFE coating successfully minimized the background fluorescence noise, allowing strong optical lipid signal to be detected within the PDMS bioreactor comparable to that of off-chip, less than 1% difference.

Perfluoroalkyl Substances (PFAS) and Their Effects on the Placenta, Pregnancy, and Child Development: a Potential Mechanistic Role for Placental Peroxisome Proliferator-Activated Receptors (PPARs)

PURPOSE OF REVIEW

This review summarizes studies highlighting perfluoroalkyl substances (PFAS) and their effects on the placenta, pregnancy outcomes, and child health. It highlights human population-based associations as well as in vitro-based experimental data to inform an understanding of the molecular mechanisms underlying these health effects. Among the mechanisms by which PFAS may induce toxicity is via their interaction with the peroxisome proliferator-activated receptors (PPARs), nuclear receptors that regulate lipid metabolism and placental functions important to healthy pregnancies, as well as fetal and child development.

RECENT FINDINGS

In utero exposure to prevalent environmental contaminants such as PFAS is associated with negative health outcomes during pregnancy, birth outcomes, and later in life. Specifically, PFAS have been associated with increased incidence of gestational diabetes, childhood obesity, preeclampsia, and fetal growth restriction. In terms of placental molecular mechanisms underlying these associations, studies demonstrate that PFAS interfere with trophoblast lipid homeostasis, inflammation, and invasion. Moreover these effects could be mediated in part by the interaction between PFAS and PPARs, as well as other biological mechanisms. This review summarizes how PFAS, critical environmental contaminants, may contribute to diseases of pregnancy as well as early and later child health.

Exposure to Perfluoroalkyl Chemicals and Cardiovascular Disease: Experimental and Epidemiological Evidence

Polyfluoro- and perfluoro-alkyl substances (PFAS) are organic chemicals extensively used worldwide for industry and consumer products. Due to their chemical stability, PFAS represent a major cause of environmental pollution. PFAS accumulate in animal and human blood and tissues exerting their toxicity. We performed a review of the epidemiological studies exploring the relationship between exposure to PFAS and thromboembolic cardiovascular disease. An increase in cardiovascular disease or death related to PFAS exposure has been reported from cross-sectional and longitudinal observational studies with evidence concerning the relation with early vascular lesions and atherosclerosis. Several studies indicate an alteration in lipid and glucose metabolism disorders and increased blood pressure as a possible link with cardiovascular thromboembolic events. We also examined the recent evidence indicating that legacy and new PFAS can be incorporated in platelet cell membranes giving a solid rationale to the observed increase risk of cardiovascular events in the populations exposed to PFAS by directly promoting thrombus formation. Exposure to PFAS has been related to altered plasma membrane fluidity and associated with altered calcium signal and increased platelet response to agonists, both in vitro and ex vivo in subjects exposed to PFAS. All the functional responses are increased in platelets by incorporation of PFAS: adhesion, aggregation, microvesicles release and experimental thrombus formation. These findings offer mechanistic support the hypothesis that platelet-centred mechanisms may be implicated in the increase in cardiovascular events observed in populations chronically exposed to PFAS.

Binding of Per- and Polyfluoroalkyl Substances to the Human Pregnane X Receptor

Per- and polyfluoroalkyl substances (PFASs) are a class of environmentally persistent industrial compounds that disrupt various metabolic pathways. Among the protein receptors to which PFASs bind, the human pregnane X receptor (hPXR) is found to be a host for a variety of long- and short-chain PFASs that lead to its overactivation. Overactivation of hPXR is linked to potential endocrine disruption, oxidative stress, hepatic steatosis, and adverse drug interactions. In this study, molecular dynamics (MD) is used to study the binding between hPXR and a number of PFAS compounds, including alternatives whose activity on hPXR has not been experimentally tested. This is the first-time MD is used to study the interactions between PFASs and hPXR, showing how relative binding free energies of PFASs relate to hPXR agonism. Binding free energy calculations, hydrogen bond analysis, per-residue decomposition calculations, and alanine scanning studies are done to provide further insight. Activities on hPXR for several short-chain and alternative PFAS compounds to long-chain PFASs that have yet to be reported will also be considered. These short-chain and alternative species include perfluorobutane sulfonic acid (PFBS), Gen-X (trade name for 2,3,3,3-tetrafluoro-2-heptafluoropropoxy propanoic acid), ADONA (trade name for 4,8-dioxa-3H-perfluorononanoic acid), and 6:2 fluorotelomer carboxylic acid (6:2 FTCA). The study shows key aspects of PFAS recognition on the hPXR, the link between PFAS binding to hPXR and the hPXR activity change observed upon the PFAS exposure, and the potential effects of alternative PFASs on hPXR activity.

The Influence of Surface Topography and Wettability on Escherichia coli Removal from Polymeric Materials in the Presence of a Blood Conditioning Film

The reduction of biofouling and the reduction of cross-contamination in the food industry are important aspects of safety management systems. Polymeric surfaces are used extensively throughout the food production industry and therefore ensuring that effective cleaning regimes are conducted is vital. Throughout this study, the influence of the surface characteristics of three different polymeric surfaces, polytetrafluoroethylene (PTFE), poly(methyl methacrylate) (PMMA) and polyethylene terephthalate (PET), on the removal of Escherichia coli using a wipe clean method utilising 3% sodium hypochlorite was determined. The PTFE surfaces were the roughest and demonstrated the least wettable surface (118.8°), followed by the PMMA (75.2°) and PET surfaces (53.9°). Following cleaning with a 3% sodium hypochlorite solution, bacteria were completely removed from the PTFE surfaces, whilst the PMMA and PET surfaces still had high numbers of bacteria recovered (1.2 × 107 CFU/mL and 6.3 × 107 CFU/mL, respectively). When bacterial suspensions were applied to the surfaces in the presence of a blood conditioning film, cleaning with sodium hypochlorite demonstrated that no bacteria were recovered from the PMMA surface. However, on both the PTFE and PET surfaces, bacteria were recovered at lower concentrations (2.0 × 102 CFU/mL and 1.3 × 103 CFU/mL, respectively). ATP bioluminescence results demonstrated significantly different ATP concentrations on the surfaces when soiled (PTFE: 132 relative light units (RLU), PMMA: 80 RLU and PET: 99 RLU). Following cleaning, both in the presence and absence of a blood conditioning film, all the surfaces were considered clean, producing ATP concentrations in the range of 0-2 RLU. The results generated in this study demonstrated that the presence of a blood conditioning film significantly altered the removal of bacteria from the polymeric surfaces following a standard cleaning regime. Conditioning films which represent the environment where the surface is intended to be used should be a vital part of the test regime to ensure an effective disinfection process.

The Toxicity of Secondary Lithium-Sulfur Batteries Components

Currently, apart from the widely known lithium-ion batteries, there are competitive solutions in the form of, for example, Li-S batteries. While the results of studies on the toxicity of Li-ion battery components are published, such studies on the components of Li-S cells are just beginning. The purpose of the current review was to identify materials used in the production of Li-S batteries and their toxicity, especially for humans. The review showed many kinds of materials with different levels of toxicity utilized for manufacturing of these cells. Some materials are of low toxicity, while some others are of the high one. A lot of materials have assigned different hazard statements. For some of the materials, no hazard statements were assigned, although such materials are toxic. No data related to the toxicity of some materials were found in the literature. This points out the need to further studies on their toxicity and legal actions to assign appropriate hazard statements.

Per- and Polyfluoroalkyl Substances Differentially Inhibit Placental Trophoblast Migration and Invasion In Vitro

Per- and polyfluoroalkyl substances (PFAS) are used as industrial surfactants and chemical coatings for household goods such as Teflon. Despite regulatory efforts to phase out legacy PFAS, they remain detectable in drinking water throughout the United States. This is due to the stability of legacy PFAS and the continued use of replacement compounds. In humans, PFAS have been detected in placenta and cord blood and are associated with low birth weight and preeclampsia risk. Preeclampsia is a leading cause of maternal mortality and is driven by insufficient endometrial trophoblast invasion, resulting in poor placental blood flow. PFAS alter invasion of other cell types, but their impact on trophoblasts is not understood. We therefore assessed the effects of PFAS on trophoblast migration, invasion, and gene expression in vitro. Trophoblast migration and invasion were assessed using a modified scratch assay in the absence or presence of Matrigel, respectively. Treatment with perfluorooctanoic sulfate (PFOS), perfluorooctanoic acid (PFOA), and GenX (1000 ng/ml) each decreased trophoblast migration over 24 h. However, only GenX (1000 ng/ml) significantly inhibited trophoblast invasion. Treatment with PFOS, PFOA, and GenX also decreased trophoblast expression of chemokines (eg, CCL2), chemokine receptors (eg, CCR4), and inflammatory enzymes (eg, ALOX15) involved in migration. Inhibition of chemokine receptors with pertussis toxin (10 ng/ml), a G-protein inhibitor, inhibited trophoblast migration similar to the PFAS. Taken together, PFAS decrease trophoblast migration, invasion, and inflammatory signaling. By understanding the mechanisms involved, it may be possible to identify the biological and exposure factors that contribute to preeclampsia.

Effect of PEEK and PTFE coatings in fatigue performance of dental implant retaining screw joint: An in vitro study

OBJECTIVES

Mechanical complications play a key role in failure of dental implants. Retaining screw loosening was one of the most commonly encountered. This study investigated the effect of PEEK and PTFE coatings on dental implant screw thread joint.

METHODS

Retaining screws were coated with PEEK and PTFE in thickness of 30 μm and 60 μm. Friction coefficient and clamping force of screw thread pair were measured, single load-to-fracture (SLF) test and dynamic fatigue life (DFL) test were done to test the stability of implant thread connection. After that, screw fracture mode and erosion morphology of screw surface and implant internal thread were observed.

RESULTS

The results showed that both PEEK and PTFE coatings could reduce friction coefficient, and consequently increase clamping force, especially PTFE coatings. PEEK coatings had no significant effect on fracture load, while 30 μm PTFE coating reduced fracture load. PEEK coatings also elongated fatigue life and improved the anti-loosening property under dynamic load, while 30 μm PTFE coating shortened fatigue life. Most of the screw fracture happened at the first thread of the retaining screws. The fracture-end of PEEK coated screws were loosed and could easily remove, but fracture-end of PTFE screws could not. Internal thread observation showed that both PEEK and PTFE coatings could reduce wear of implant internal thread.

CONCLUSION

PEEK coatings could effectively improve the stability of implant threaded connection, and reduce wear of implant internal thread. PEEK coating may be a suitable way to prevent screw loosening.