Preparation of agricultural by-product based anion exchanger and its utilization for nitrate and phosphate removal

Competitive Removal of Perchlorate Ions by Quaternary Amine Modified Reed in the Presence of Nitrate and Phosphate

We report a kinetic and equilibrium study in which we examined the removal of perchlorate anions from water by adsorption onto modified reed (MR), an adsorption material constituted by giant reed (GR) particles whose anion adsorption properties have been enhanced by quaternary amine (QA) crosslinking. In particular, we examined how MR adsorption of perchlorate interacts competitively with concomitant adsorption of agriculture-derived phosphate and nitrate contaminants. Equilibrium and pH experiments were first conducted in single-component systems, the results of which were best described by the Langmuir-Freundlich (L-F) isotherm. Subsequent analyses of competitive effects on adsorption showed that although MR had a higher adsorption capacity for perchlorate alone than for nitrate or phosphate alone, the addition of either phosphate or nitrate to a perchlorate solution had a diminishing effect on MR adsorption of perchlorate within a natural-water pH range, with phosphate having the stronger competitive effect. Perchlorate adsorption on MR varied inversely with competing ion concentrations, providing direct evidence of the perchlorate diminution effect being attributable to anion competition. Finally, we developed a multicomponent isotherm model that describes the binary adsorption of perchlorate in the presence of each of these competing anions. The results of this work provide perchlorate removal efficiency information that is directly applicable to the design of water treatment systems.

Phosphate ion removal from aqueous solution using snail shell dust: biosorption potential of waste shells of edible snails

The freshwater snails, Filopaludina bengalensis and Pila globosa are widely used for human consumption and as a feed in aquaculture in India and Bangladesh. The generation of shells as a waste product following meat extraction from the live snails incites their utilisation as a potential biomaterial. Shell dust was prepared from the dried shells of F. bengalensis (FSD) and P. globosa (PSD) and employed for phosphate adsorption from aqueous solutions. Batch adsorption experiments were performed to examine the effects of various experimental conditions, such as biosorbent dose, agitation speed, temperature, contact time, pH, initial concentration of phosphate ions, and presence of co-existing ions. SEM, EDS, ICP-OES, FTIR, and XRD results indicated that phosphate ions were adsorbed onto the surface of shell dust particles. The experimental data fitted with the Langmuir isotherm with a maximum adsorption capacity of 62.50 and 66.66 mg g^-1 for FSD and PSD. The pseudo-second order kinetic model was well fitted, indicating the chemical adsorption process, and the thermodynamic parameters indicated that the adsorption mechanism of phosphate was spontaneous, feasible, and endothermic. Therefore, the results have established the potentiality of the waste shells of edible snails to be used as an eco-friendly and low-cost biosorbent for phosphate removal from wastewater.

Nitrate contamination in water resources, human health risks and its remediation through adsorption: a focused review

The level of nitrate in water has been increasing considerably all around the world due to vast application of inorganic nitrogen fertiliser and animal manure. Because of nitrate's high solubility in water, human beings are getting exposed to it mainly through various routes including water, food etc. Various regulations have been set for nitrate (45-50 mgNO₃^-/L) in drinking water to protect health of the infants from the methemoglobinemia, birth defects, thyroid disease, risk of specific cancers, i.e. colorectal, breast and bladder cancer caused due to nitrate poisoning. Different methods like ion exchange, adsorption, biological denitrification etc. have the ability to eliminate the nitrate from the aqueous medium. However, adsorption process got preference over the other approaches because of its simple design and satisfactory results especially with surface modified adsorbents or with mineral-based adsorbents. Different types of adsorbents have been used for this purpose; however, adsorbents derived from the biomass wastes have great adsorption capacities for nitrate such as tea waste-based adsorbents (136.43 mg/g), carbon nanotube (142.86 mg/g), chitosan beads (104 mg/g) and cetyltrimethylammonium bromide modified rice husk (278 mg/g). Therefore, a thorough literature survey has been carried out to formulate this review paper to understand various sources of nitrate pollution, route of exposure to the human beings, ill effects along with discussing the key developments as well as the new advancements reported in procuring low-cost efficient adsorbents for water purification.

Phosphorous removal and recovery from urban wastewater: Current practices and new directions

Phosphate rocks are an irreplaceable resource to produce fertilizers, but their availability will not be enough to meet the increasing demands of agriculture for food production. At the same time, the accumulation of phosphorous discharged by municipal wastewater treatment plants (WWTPs) is one of the main causes of eutrophication. In a perspective of circular economy, WWTPs play a key role in phosphorous management. Indeed, phosphorus removal and recovery from WWTPs can both reduce the occurrence of eutrophication and contribute to meeting the demand for phosphorus-based fertilizers. Phosphorous removal and recovery are interconnected phases in WWTP with the former generally involved in the mainstream treatment, while the latter on the side streams. Indeed, by reducing phosphorus concentration in the WWTP side streams, a further improvement of the overall phosphorus removal from the WWTP influent can be obtained. Many studies and patents have been recently focused on treatments and processes aimed at the removal and recovery of phosphorous from wastewater and sewage sludge. Notably, new advances on biological and material sciences are constantly put at the service of conventional or unconventional wastewater treatments to increase the phosphorous removal efficiency and/or reduce the treatment costs. Similarly, many studies have been devoted to the development of processes aimed at the recovery of phosphorus from wastewaters and sludge to produce fertilizers, and a wide range of recovery percentages is reported as a function of the different technologies applied (from 10-25% up to 70-90% of the phosphorous in the WWTP influent). In view of forthcoming and inevitable regulations on phosphorous removal and recovery from WWTP streams, this review summarizes the main recent advances in this field to provide the scientific and technical community with an updated and useful tool for choosing the best strategy to adopt during the design or upgrading of WWTPs.

Recent advances and challenges on removal and recycling of phosphate from wastewater using biomass-derived adsorbents

As the severe damage of phosphate enrichment in the water ecosystem and the supply shortage of phosphate rock, developing an efficient method for the removal and recycling of phosphate from wastewater is of great significance. To achieve this goal, adsorption technology has been widely investigated, and various adsorbents were developed. Among them, the biomass-derived adsorbents including biomass-derived carbon-based materials, biomass-based anion exchangers and metal-biomass composites have attracted increasing attention over the past years due to the low cost, abundant renewable raw materials and environmental friendliness. However, different adsorbents usually exhibit variable adsorption performances for phosphate, which highly depends on their design strategies, preparation methods and potential adsorption mechanisms. Thus, this review comprehensively summarizes the recent researches on the removal and recycling of phosphate from wastewater using the biomass-derived adsorbents. Especially, the design strategies, preparation methods, adsorption performances and mechanisms of these reported biomass-derived adsorbents are discussed in detail. Moreover, as the significant strategies to recover and recycling phosphate, the elution and direct use of phosphate-loaded adsorbents as fertilizers are also presented. Although the excellent adsorption performance has been obtained, some challenges are still existing, which should be given more attention in the following researches to facilitate the development and industrial application of biomass-derived adsorbents.

Ethylenediamine and Pentaethylene Hexamine Modified Bamboo Sawdust by Radiation Grafting and Their Adsorption Behavior for Phosphate

Phosphate is an important component for the growth of plants and microorganisms; however, excess phosphate causes serious eutrophication in natural waters. New potential low-loss adsorbents from natural biomass for phosphate removal are desired. Bamboo is one of the most abundant renewable cellulose resources; however, the pure bamboo cellulose is poor to adsorb phosphate. To enhance the adsorption capacity, in this work, bamboo sawdust (BS) was chemically modified by two kinds of amines. First, glycidyl methacrylate (GMA) was grafted on BS using radiation induced graft polymerization. Then, the GMA-grafted BS was further modified by a ring-opening reaction with amines, including ethylenediamine (EDA) and pentaethylene hexamine (PEHA). The amine groups were then quaternized to prepare the BS-GMA-EDA-Q and BS-GMA-PEHA-Q adsorbents. The adsorbents were characterized by FTIR, SEM, TG, and XPS analysis. The adsorption performances of the adsorbents for phosphate were evaluated through batch experiments. The adsorption by BS-GMA-EDA-Q and BS-GMA-PEHA-Q both well obeyed the pseudo-second-order kinetic model and the Langmuir isotherm model, indicating that the adsorption process was chemical monomolecular layer adsorption. The maximum adsorption capacities for BS-GMA-EDA-Q and BS-GMA-PEHA-Q calculated by the Langmuir model were 85.25 and 152.21 mg/g, respectively. A total of 1 mol/L HCl was used to elute the saturated adsorbents. A negligible decrease in adsorption capacity was found after five adsorption–desorption cycles.

Effect of mineral loaded biochar on the leaching performances of nitrate and phosphate in two contrasting soils from the coastal estuary area

Coastal estuary area is an important sink for the land-based or/and atmosphere-based nutrients, and is suffering a serious destruction derived from the intensifying human activities, which subsequently threatens the marine environment. Therefore, increasing soil retention capacities of nitrogen (N) and phosphorous (P) and reducing their leaching amount to sea water become a critical issue needed to be urgently addressed. In this study, a 38-day incubation and leaching experiment was conducted with two contrasting soils taken from the coastal estuary area, including the wetland and agricultural soils. Four kinds of biochars (BC), including one pure reed straw BC (BC₀), and three mineral loaded BCs produced through the co-pyrolysis of reed straw with CaO (BC_Ca), MgO (BC_Mg), and shell powder (BC_SP), respectively, were used to explore their effects on the leaching performances of nitrate-N and phosphate-P. The results demonstrated that the application of mineral loaded BCs could generally decrease the leaching amount of phosphate-P, while showed little effect on the nitrate-N leaching, compared to the controls. The positive improvement in soil nutrient retention capacity, mostly contributed by the increased adsorption on BC surface and into aperture, was suggested as the main mechanism for the decrease in nitrate-N and phosphate-P leaching. Compared to the agricultural soil, high clay content in the wetland soil could weaken the reduction potential in leaching losses of nitrate-N and phosphate-P derived from the newly introduced minerals with BC application. Furthermore, our results also indicated that the mineral loaded BCs may slow down the conversion rate of nutrients from organic forms to inorganic forms supported by the decreased enzymatic activity, which would be beneficial to the long term retention of nutrients in soil. Overall, based on the findings in the present study, the BC_Mg and Ca loaded BCs were respectively recommended for the wetland and agricultural soils.

Development of triaminotriazine functionalized graphene oxide capped chitosan porous composite beads for nutrients remediation towards water purification

The porous, definite and nitrogen rich triaminotriazine (TAT) grafted graphene oxide (GO) known as TATGO composite was developed for nutrients (NO₃^- and PO₄^3-) retention. Additionally, the structural property of TATGO composite was improved with the use of chitosan (CS) to produce easily separable TATGO@CS hybrid beads which possess the significant NO₃^- and PO₄^3- adsorption capacities of 58.46 and 61.38 mg/g respectively than their individual materials. The instrumentations such as SEM, TGA, FTIR, EDAX, XRD and BET studies were executed for adsorbents. The optimization of the parameters accountable for adsorption process was performed in batch scale. The effect of isotherms (Langmuir, Freundlich and Dubinin-Radushkevich (D-R)), kinetics (pseudo-first/second order and particle/intraparticle diffusion) and thermodynamic parameters (ΔG°, ΔH° and ΔS°) of the adsorption was explored. The removal mechanism of TATGO@CS hybrid beads was to be electrostatic attraction on NO₃^- and PO₄^3-. The field applicability and reuse of TATGO@CS hybrid beads was also inspected.

Review on the Evaluation of the Impacts of Wastewater Disposal in Hydraulic Fracturing Industry in the United States

This paper scrutinized hydraulic fracturing applications mainly in the United States with regard to both groundwater and surface water contamination with the purpose of bringing forth objective analysis of research findings. Results from previous studies are often unconvincing due to the incomplete database of chemical additives; after and before well-founded water samples to define the change in parameters; and specific sources of water pollution in a particular region. Nonetheless, there is a superior chance of both surface and groundwater contamination induced by improper and less monitored wastewater disposal and management practices. This report has documented systematic evidence for total dissolved solids, salinity, and methane contamination regarding drinking water correlated with hydraulic fracturing. Methane concentrations were found on an average rate of 19.2 mg/L, which is 17 times higher than the acceptance rate and the maximum value was recorded as 64.2 mg/L near the active hydraulic fracturing drilling and extraction zones than that of the nonactive sites (1.1 mg/L). The concentration of total dissolved solids (350 g/L) was characterized as a voluminous amount of saline wastewater, which was quite unexpectedly high. The paper concludes with plausible solutions that should be implemented to avoid further contamination.

Preparation, Characterization, and Application of Novel Ferric Oxide-Amine Material for Removal of Nitrate and Phosphate in Water

Ferric oxide-amine material was synthesized and applied as a novel adsorbent for nitrate and phosphate removal from aqueous solution. The properties of ferric oxide-amine were examined using TGA, FTIR, BET, SEM, EDX, SEM-mapping, and XRD analysis. The results showed that the adsorption using ferric oxide-amine material reached equilibrium after 30 and 60 min for nitrate and phosphate, respectively. The highest nitrate and phosphate adsorption capacities were 131.4 mg nitrate/g at pH 5-6 and 42.1 mg phosphate/g at pH 6. The effects of adsorbent dosage, initial concentrations of nitrate and phosphate, and adsorption temperature were also investigated. Among the three adsorbents of ferric oxide-amine, ferric oxide, and Akualite A420 ion exchange resin, ferric oxide-amine material had the highest adsorption capacity for nitrate and phosphate removal. These results suggest a great potential use of ferric oxide-amine material for water treatment in practical applications.

Influence of coexisting calcium and magnesium ions on phosphate adsorption onto hydrous iron oxide

Removal of phosphorus (P) from municipal wastewater is of vital importance to the control of eutrophication in receiving freshwater bodies. Typical cations such as Ca²⁺ and Mg²⁺ generally exist in municipal wastewater, and they may affect the sorption behavior and mechanism of iron oxide-based materials for aqueous phosphate (H_xPO₄^x - 3, x = 0, 1, 2, or 3 depending on solution pH). To better apply iron oxide-containing materials as adsorbents to eliminate H_xPO₄^x - 3 in municipal wastewater, a hydrous ferric oxide (HFEO) was prepared and characterized at first and then the impact of coexisting Ca²⁺ and Mg²⁺ on the uptake of H_xPO₄^x - 3 by HFEO was studied. The results showed that, without coexisting Ca²⁺ and Mg²⁺, the kinetic data for H_xPO₄^x - 3 sorption onto HFEO were better described by the Elovich model (R² = 0.953) than the pseudo-second-order (R² = 0.838) and pseudo-first-order (R² = 0.641) models, and the isotherm data were fitted better with the Dubinin-Radushkevich (R² = 0.966) and Freundlich (R² = 0.953) models than with the Langmuir (R² = 0.924) model. The ligand exchange of the Fe-bound hydroxyl group with H_xPO₄^x - 3 and the generation of Fe-O-P bonding played a key role in the uptake of H_xPO₄^x - 3 by HFEO in the absence of Ca²⁺ and Mg²⁺. Coexisting Ca²⁺ and Mg²⁺ greatly improved the adsorptive removal of H_xPO₄^x - 3 by HFEO, including the adsorption capacity and initial adsorption rate. According to the Langmuir isotherm equation, the predicted maximum H_xPO₄^x - 3 adsorption capacity for HFEO at pH 7 in the presence of 2 mmol/L Ca²⁺ (24.7 mg P/g) or 2 mmol/L Mg²⁺ (18.4 mg P/g) was much larger than that without coexisting Ca²⁺ and Mg²⁺ (10.7 mg P/g). The formation of aqueous CaHPO₄⁰ and MgHPO₄⁰ species firstly and then the adsorption of the formed CaHPO₄⁰ and MgHPO₄⁰ species on the HFEO surface to generate the HPO₄^2--bridged ternary complexes (i.e., Fe(OPO₃H)Ca⁺ and Fe(OPO₃H)Mg⁺) had an important role in the improvement of H_xPO₄^x - 3 adsorption onto HFEO by coexisting Ca²⁺ and Mg²⁺.

Fixed bed study of nitrate removal from water by protonated cross-linked chitosan supported by biomass-derived carbon particles

In this study, a green adsorbent was synthesized for the removal of nitrate ions from water. The adsorbent consisted of carbonaceous particles with high specific surface area (1,240 m² g^-1) and porosity derived from pyrolysis of cornelian cherry stone and modified by protonated cross-linked chitosan. The adsorbent was characterized using various techniques like SEM, FTIR, BJH and zeta potential measurements. Dynamic behavior of the adsorbent in the nitrate adsorption was studied in a packed bed system at various operating conditions and in the presence of other competing anions (PO₄^3-, HCO₃^-, SO₄^2-). Based on the error analysis, the optimum operating conditions were considered at flow rate of 3.8 mL min^-1, bed depth of 10 cm and nitrate concentration of 75 mg L^-1. The kinetics of the adsorption process was studied using Adams-Bohart and Thomas models and the q_max was calculated to be about 12.4 mg g^-1 at neutral pH and room temperature. Furthermore, the relationship between the bed height and the breakthrough time was described by bed depth service time (BDST) model. The experimental results suggested that the adsorbent possessed significant ability in nitrate removal from water due to the desired chemistry of the biopolymer and the excellent textural properties of the carbon support.

Fabrication and evaluation of a regenerable HFO-doped agricultural waste for enhanced adsorption affinity towards phosphate

Chemical modification of agricultural waste biomass has proved to be an economy and effective approach to capture phosphate ions, except for that under acidic conditions and highly competitive ion systems. According to this, a new nanocomposite (HFO@St+) was fabricated by incorporating nano-sized hydrous Fe(III) oxides (HFO) within aminated wheat straw in order to overcome the bottleneck. The optimal pH of phosphate uptake by HFO@St+ was greatly broadened and observed over a wide pH range between 2.0 and 7.0. The binary exchange reaction indicated that phosphate was strongly and preferably adsorbed by HFO@St+ with the separation factor K of phosphate over nitrate increasing from 0.23-1 or 0.20-0.26 to 2.5-38 or 2.5-15 for near neutral or acidic pHs, respectively. The sorption selectivity for HFO@St+ followed the order of phosphate > nitrate > chloride under experimental conditions. The presence of inorganic and organic ligands (SO₄ and HA) showed no significant effect on phosphate adsorption. XPS and FT-IR analyses were performed to explore the underlying mechanism of adsorption. The exhausted material could be regenerated with NaOH-NaCl solution for at least ten cycles, indicating that HFO@St+ can be used as a sustainable biomass product with excellent adsorption affinity for phosphate removal.

Radiation Synthesis of Pentaethylene Hexamine Functionalized Cotton Linter for Effective Removal of Phosphate: Batch and Dynamic Flow Mode Studies

A quaternized cotton linter fiber (QCLF) based adsorbent for removal of phosphate was prepared by grafting glycidyl methacrylate onto cotton linter and subsequent ring-opening reaction of epoxy groups and further quaternization. The adsorption behavior of the QCLF for phosphate was evaluated in a batch and column experiment. The batch experiment demonstrated that the adsorption process followed pseudo-second-order kinetics with an R² value of 0.9967, and the Langmuir model with R² value of 0.9952. The theoretical maximum adsorption capacity reached 152.44 mg/g. The experimental data of the fixed-bed column were well fitted with the Thomas and Yoon-Nelson models, and the adsorption capacity of phosphate at 100 mg/L and flow rate 1 mL/min reached 141.58 mg/g. The saturated QCLF could be regenerated by eluting with 1 M HCl.

Triamine-bearing activated rice husk ash as an advanced functional material for nitrate removal from aqueous solution

In this study, we proposed a simple method for preparing triamine-bearing activated rice husk ash material (TRI-ARHA) as an advanced functional material with high nitrate adsorption capacity and durability. The novel TRI-ARHA was generated via a post-synthesis grafting method and modified by acidification to form ammonium moiety. TRI-ARHA was then characterized by using thermogravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy and SEM-mapping. The TRI-ARHA had high nitrate adsorption capacity of 163.4 mgNO₃ ^-/g, which was 2.06 times higher than that of a commercial anion exchange resin (Akualite A420) due to strong interactions of Si, C, and N in the material structure. This functional material with good durability after 10 cycles could be very promising for adsorption of other anions (e.g. sulfate and phosphate) in water and wastewater treatment.

Comparative analysis on adsorption properties and mechanisms of nitrate and phosphate by modified corn stalks

We compare and analyze the different properties and mechanisms of MCS on nitrate and phosphate.

Enhanced removal of nitrate from water using amine-grafted agricultural wastes

Adsorption using low-cost adsorbents is a favourable water treatment method for the removal of water contaminants. In this study the enhanced removal of nitrate, a contaminant at elevated concentration affecting human health and causing eutrophication of water, was tested using chemically modified agricultural wastes as adsorbents. Batch and fixed-bed adsorption studies were performed on corn cob and coconut copra that were surface modified by amine-grafting to increase the surface positive charges. The Langmuir nitrate adsorption capacities (mgN/g) were 49.9 and 59.0 for the amine-grafted (AG) corn cob and coconut copra, respectively at pH6.5 and ionic strength 1×10(-3)M NaCl. These values are higher than those of many commercially available anion exchange resins. Fixed-bed (15-cm height) adsorption capacities (mgN/g) calculated from the breakthrough curves were 15.3 and 18.6 for AG corn cob and AG coconut copra, respectively, for an influent nitrate concentration 20mg N/L at a flow velocity 5m/h. Nitrate adsorption decreased in the presence of sulphate, phosphate and chloride, with sulphate being the most competitive anion. The Thomas model fitted well to the fixed-bed adsorption data from four repeated adsorption/desorption cycles. Plug-flow model fitted well to the data from only the first cycle.

Pyridinium-functionalized magnetic mesoporous silica nanoparticles as a reusable adsorbent for phosphate removal from aqueous solution

In this work, pyridinium-functionalized silica nanoparticles adsorbent (PC/SiO2/Fe3O4) was synthesized for phosphate removal from aqueous solutions. The removal efficiency of phosphate on the PC/SiO2/Fe3O4 was carried out and investigated under various conditions such as pH, contact temperature and initial concentration. The results showed that the adsorption equilibrium could be reached within 10 min, which fitted a Langmuir isotherm model, with maximum adsorption capacity of 94.16 mg/g, and the kinetic data were fitted well by pseudo-second-order and intra-particle diffusion models. Phosphate loaded on the adsorbents could be easily desorbed with 0.2 mol/L of NaOH, and the adsorbents showed good reusability. The adsorption capacity was still around 50 mg/g after 10 times of reuse. All the results demonstrated that this pyridinium-functionalized mesoporous material could be used for the phosphate removal from aqueous solution and it was easy to collect due to its magnetic properties.

Application of modified chitosan microspheres for nitrate and phosphate adsorption from aqueous solution

Modified chitosan microspheres were prepared by inverse suspension crosslinking and used for nitrate and phosphate adsorption from aqueous solution. Their surface was coarse and porous compared to pure chitosan microspheres and they were about 100 μm in size.

Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles

The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI) failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH) showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO4(2-), NO3(-) and Cl(-)); however, CO3(2-) exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC) assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions.

Fabrication of a Biomass-Based Hydrous Zirconium Oxide Nanocomposite for Preferable Phosphate Removal and Recovery

Advanced removal of phosphate by low-cost adsorbents from municipal wastewater or industrial effluents is an effective and economic way to prevent the occurrence of eutrophication. Here, we proposed a novel method to immobilize hydrous zirconium oxide nanoparticle within quaternary-aminated wheat straw, and obtained an inexpensive, eco-friendly nanocomposite Ws-N-Zr. The biomass-based Ws-N-Zr exhibited higher preference toward phosphate than commercial anion exchanger IRA-900 when competing sulfate ions coexisted at relatively high levels. Such excellent performance of Ws-N-Zr resulted from its specific hybrid structure, the quaternary ammonium groups bonded on the host favor the preconcentration of phosphate ions inside the wheat straw based on Donnan effect, and the encapsulated HZO nanoparticle exhibits preferable sequestration of phosphate ions through specific interaction, as further demonstrated by FTIR and X-ray photoelectron spectroscopy. Cycle adsorption and regeneration experiments demonstrated that Ws-N-Zr could be employed for repeated use without significant capacity loss, when the binary NaOH-NaCl solution was employed as the regenerant. The influence of solution pH and contact time was also examined. The results suggested that Ws-N-Zr has a great potential in efficient removal of phosphate in contaminated waters.

High-capacity adsorption of dissolved hexavalent chromium using amine-functionalized magnetic corn stalk composites

Easily separable amine-functionalized magnetic corn stalk composites (AF-MCS) were employed for effective adsorption and reduction of toxic hexavalent chromium [Cr(VI)] to nontoxic Cr(III). The saturated magnetization of AF-MCS reached 6.2emu/g, and as a result, it could be separated from aqueous solution by a magnetic process for its superparamagnetism. The studies of various factors influencing the sorption behavior indicated that the optimum AF-MCS dosage for Cr(VI) adsorption was 1g/L, and the maximum adsorption capacity was observed at pH 3.0. The chromium adsorption perfectly fitted the Langmuir isotherm model and pseudo second order kinetic model. Furthermore, characterization of AF-MCS was investigated by means of XRD, SEM, TEM, FT-IR, BET, VSM and XPS analysis to discuss the uptake mechanism. Basically, these results demonstrated that AF-MCS prepared in this work has shown its merit in effective removal of Cr(VI) and rapid separation from effluents simultaneously.

Removal of nitrate by modified pine sawdust: effects of temperature and co-existing anions

The effect of temperature, sulphate and phosphate, and the initial nitrate concentration on nitrate removal was studied with synthetic solutions. Chemically modified pine sawdust (Pinus sylvestris) anion exchange resin (MPSD) was used in the sorption studies. The resin was synthesized by reacting pine sawdust with epichlorohydrin, ethylenediamine and triethylamine in the presence of N,N-dimethylformamide. Nitrate removal was successful at 5-70 °C. Higher temperatures caused nitrate removal to decrease moderately, but sorption capacities of 22.2-32.8 mg/g for NO3-N were achieved. The removal of nitrate in the presence of sulphate or phosphate was studied at concentrations of 30 mg N/l, 10-500 mg S/l and 1-50 mg P/l. A significant decrease in nitrate reduction was observed at sulphate and phosphate concentrations of 100 mg S/l and 50 mg P/l, respectively. The effect of initial nitrate concentration was studied in column. Nitrate sorption was clearly dependent on the initial concentration. Desorption of nitrate in column was completed using about 80 bed volumes of 0.1 M NaCl solution. The sorption data were fitted to the Langmuir, Freundlich and Redlich-Peterson adsorption models. The Redlich-Peterson and Langmuir models gave the best fit, which suggests monolayer sorption. Thermodynamic studies revealed that the sorption of nitrate was spontaneous and exothermic in nature. The results imply that modified pine sawdust could be a feasible alternative in the treatment of real industrial wastewaters.

Modification of agricultural waste/by-products for enhanced phosphate removal and recovery: potential and obstacles

There is a growing trend to employ agricultural waste/by-products (AWBs) as the substrates for the development of phosphate biosorbents. Nevertheless, due to the lack of anion binding sites, natural AWBs are usually inefficient in phosphate decontamination. Consequently, modification plays a vital role in improving phosphate sorption's property of raw AWBs. This review paper evaluates all existing methods of modification. The literatures indicate that modification can significantly improve phosphate removal ability of AWBs by retaining phosphate ion onto modified AWBs principally via ion exchange (electrostatic interaction) and ligand exchange mechanisms. So far, little work has been done on the beneficial use of modified AWBs for the phosphorus recovery from aqueous solutions. The poor recyclability of modified AWBs could be responsible for their limited application. Hence, further study is essential to search for novel, cost-effective, and green methods of modification.

Phosphorus elimination from aqueous solution using 'zirconium loaded okara' as a biosorbent

This work deals with the capture of phosphorus from aqueous solutions by biosorption onto zirconium loaded okara (ZLO). The batch-mode experiments were conducted to examine the effect of pH, biosorbent dose, initial phosphorus concentration, contact time, and temperature on the process. It was found that, the adsorption was most favored in the pH range of 2-6. The optimal doses for the adsorption, at initial phosphorus concentrations of 5, 10, 25, 50mg/L were 2, 3, 7, 10g/L, respectively. The maximum adsorption capacity of ZLO was approximately 44.13mg PO4/g at 298K. The phosphate removal was rapid, reaching 95% in 30min. Freundlich model best fitted the equilibrium data, while Pseudo-second order model satisfactorily described the kinetic results. Thermodynamic analysis revealed feasible, spontaneous, and endothermic nature of the process. The research would be beneficial for developing a promising, eco-friendly phosphorus biosorbent from a plentiful AWB - okara.

The temporal transcriptomic response of Pinus massoniana seedlings to phosphorus deficiency

BACKGROUND

Phosphorus (P) is an essential macronutrient for plant growth and development. Several genes involved in phosphorus deficiency stress have been identified in various plant species. However, a whole genome understanding of the molecular mechanisms involved in plant adaptations to low P remains elusive, and there is particularly little information on the genetic basis of these acclimations in coniferous trees. Masson pine (Pinus massoniana) is grown mainly in the tropical and subtropical regions in China, many of which are severely lacking in inorganic phosphate (Pi). In previous work, we described an elite P. massoniana genotype demonstrating a high tolerance to Pi-deficiency.

METHODOLOGY/PRINCIPAL FINDINGS

To further investigate the mechanism of tolerance to low P, RNA-seq was performed to give an idea of extent of expression from the two mixed libraries, and microarray whose probes were designed based on the unigenes obtained from RNA-seq was used to elucidate the global gene expression profiles for the long-term phosphorus starvation. A total of 70,896 unigenes with lengths ranging from 201 to 20,490 bp were assembled from 112,108,862 high quality reads derived from RNA-Seq libraries. We identified 1,396 and 943 transcripts that were differentially regulated (P<0.05) under P1 (0.01 mM P) and P2 (0.06 mM P) Pi-deficiency conditions, respectively. Numerous transcripts were consistently differentially regulated under Pi deficiency stress, many of which were also up- or down-regulated in other species under the corresponding conditions, and are therefore ideal candidates for monitoring the P status of plants. The results also demonstrated the impact of different Pi starvation levels on global gene expression in Masson pine.

CONCLUSIONS/SIGNIFICANCE

To our knowledge, this work provides the first insight into the molecular mechanisms involved in acclimation to long-term Pi starvation and different Pi availability levels in coniferous trees.