White-rot fungi pretreatment combined with alkaline/oxidative pretreatment to improve enzymatic saccharification of industrial hemp

Recent advances in eco-friendly technology for decontamination of pulp and paper mill industrial effluent: a review

The economic development of a country directly depends upon industries. But this economic development should not be at the cost of our natural environment. A substantial amount of water is spent during paper production, creating water scarcity and generating wastewater. Therefore, the Pollution Control Board classifies this industry into red category. Water is used in different papermaking stages such as debarking, pulping or bleaching, washing, and finishing. The wastewater thus generated contains lignin and xenobiotic compounds such as resin acids, chlorinated lignin, phenols, furans, dioxins, chlorophenols, adsorbable organic halogens (AOX), extractable organic halogens (EOCs), polychlorinated biphenyls, plasticizers, and polychlorinated dibenzodioxins. Nowadays, several microorganisms are used in the detoxification of these hazardous effluents. Researchers have found that microbial degradation is the most promising treatment method to remove high biological oxygen demand (BOD) and chemical oxygen demand (COD) from wastewater. Microorganisms also remove AOX toxicity, chlorinated compounds, suspended solids, color, lignin, derivatives, etc. from the pulp and paper mill effluents. But in the current scenario, mill effluents are known to deteriorate the environment and therefore it is highly desirable to deploy advanced technologies for effluent treatment. This review summarizes the eco-friendly advanced treatment technologies for effluents generated from pulp and paper mills.

Hydrodynamic cavitation-assisted acid pretreatment and fed-batch simultaneous saccharification and co-fermentation for ethanol production from sugarcane bagasse using immobilized cells of Scheffersomyces parashehatae

A new alternative for hydrodynamic cavitation-assisted pretreatment of sugarcane bagasse was proposed, along with a simultaneous saccharification and co-fermentation (SSCF) process performed in interconnected columns. Influential variables in the pretreatment were evaluated using a statistical design, indicating that an ozone flow rate of 10 mg min-1 and a pH of 5.10 resulted in 86 % and 72 % glucan and xylan hydrolysis yields, respectively, in the subsequent enzymatic hydrolysis process. Under these optimized conditions, iron sulfate (15 mg L-1) was added to assess Fenton pretreatment, resulting in glucan and xylan hydrolysis yields of 92 % and 71 %, respectively, in a material pretreated for 10 min. In SSCF, ethanol volumetric productivities of 0.33 g L-1 h-1 and of 0.54 g L-1 h-1 were obtained in batch and fed-batch operation modes, achieving 26 g L-1 of ethanol in 48 h in the latter mode.

Pretreatment and composting technology of agricultural organic waste for sustainable agricultural development

With the continuous development of agriculture, Agricultural organic waste (AOW) has become the most abundant renewable energy on earth, and it is a hot spot of research in recent years to realize the recycling of AOW to achieve sustainable development of agricultural production. However, lignocellulose, which is difficult to degrade in AOW, greenhouse gas emissions, and pile pathogenic fungi and insect eggs are the biggest obstacles to its return to land use. In response to the above problems researchers promote organic waste recycling by pretreating AOW, controlling composting conditions and adding other substances to achieve green return of AOW to the field and promote the development of agricultural production. This review summarizes the ways of organic waste treatment, factors affecting composting and problems in composting by researchers in recent years, with a view to providing research ideas for future related studies.

Strategies of pretreatment of feedstocks for optimized bioethanol production: distinct and integrated approaches

Bioethanol is recognized as a valuable substitute for renewable energy sources to meet the fuel and energy demand of the nation, considered an environmentally friendly resource obtained from agricultural residues such as sugarcane bagasse, rice straw, husk, wheat straw and corn stover. The energy demand is sustained using lignocellulosic biomass to produce bioethanol. Lignocellulosic biomass (LCBs) is the point of attention in replacing the dependence on fossil fuels. The recalcitrant structure of the lignocellulosic biomass is disrupted using effective pretreatment techniques that separate complex interlinked structures among cellulose, hemicellulose, and lignin. Pretreatment of biomass involves various physical, chemical, biological, and physiochemical protocols which are of importance, dependent upon their individual or combined dissolution effect. Physical pretreatment involves a reduction in the size of the biomass using mechanical, extrusion, irradiation, and sonification methods while chemical pretreatment involves the breaking of various bonds present in the LCB structure. This can be obtained by using an acidic, alkaline, ionic liquid, and organosolvent methods. Biological pretreatment is considered an environment-friendly and safe process involving various bacterial and fungal microorganisms. Distinct pretreatment methods, when combined and utilized in synchronization lead to more effective disruption of LCB, making biomass more accessible for further processing. These could be utilized in terms of their effectiveness for a particular type of cellulosic fiber and are namely steam explosion, liquid hot water, ammonia fibre explosion, CO₂ explosion, and wet air oxidation methods. The present review encircles various distinct and integrated pretreatment processes developed till now and their advancement according to the current trend and future aspects to make lignocellulosic biomass available for further hydrolysis and fermentation.

Bioethanol Production from Lignocellulosic Biomass-Challenges and Solutions

Regarding the limited resources for fossil fuels and increasing global energy demands, greenhouse gas emissions, and climate change, there is a need to find alternative energy sources that are sustainable, environmentally friendly, renewable, and economically viable. In the last several decades, interest in second-generation bioethanol production from non-food lignocellulosic biomass in the form of organic residues rapidly increased because of its abundance, renewability, and low cost. Bioethanol production fits into the strategy of a circular economy and zero waste plans, and using ethanol as an alternative fuel gives the world economy a chance to become independent of the petrochemical industry, providing energy security and environmental safety. However, the conversion of biomass into ethanol is a challenging and multi-stage process because of the variation in the biochemical composition of biomass and the recalcitrance of lignin, the aromatic component of lignocellulose. Therefore, the commercial production of cellulosic ethanol has not yet become well-received commercially, being hampered by high research and production costs, and substantial effort is needed to make it more widespread and profitable. This review summarises the state of the art in bioethanol production from lignocellulosic biomass, highlights the most challenging steps of the process, including pretreatment stages required to fragment biomass components and further enzymatic hydrolysis and fermentation, presents the most recent technological advances to overcome the challenges and high costs, and discusses future perspectives of second-generation biorefineries.

Surface display of enzyme complex on Corynebacterium glutamicum as a whole cell biocatalyst and its consolidated bioprocessing using fungal-pretreated lignocellulosic biomass

A novel whole cell biocatalyst using fungal-pretreated lignocellulosic biomass was developed by displaying the enzyme complex consisting of N-acetylglucosaminidase (cNAG) and endoglucanse E (cCelE) on Corynebacterium glutamicum, hereafter called mNC. mNC showed a maximum 4.43-fold cNAG and 2.40-fold cCelE activity compared to single enzyme-secreting C. glutamicum. mNC also showed the highest efficiency of sugar production in various types of cellulose and fungal-pretreated biomass. The growth of mNC was 5.06-fold higher than that of the control. Then, the ability of mNC to produce a valuable chemical was confirmed. mNC overexpressing isopropanol biosynthesis genes showed a maximum titer of 218.9 ± 11.73 mg/L isopropanol and maintained high efficiency for isopropanol production in the recycling test, which was 90.07 ± 4.12 % during 4 cycles. This strategy can be applied to the direct saccharification of fungal-pretreated lignocellulosic biomass efficiently leading to the production of valuable products in various industrial fields.

Assessment of the Pretreatments and Bioconversion of Lignocellulosic Biomass Recovered from the Husk of the Cocoa Pod

The production of biofuels (biogas, ethanol, methanol, biodiesel, and solid fuels, etc.), beginning with cocoa pod husk (CPH), is a way for obtaining a final product from the use of the principal waste product of the cocoa industry. However, there are limitations to the bioconversion of the material due to its structural components (cellulose, hemicellulose, and lignin). Currently, CPH pretreatment methods are considered a good approach towards the improvement of both the degradation process and the production of biogas or ethanol. The present document aims to set out the different methods for pretreating lignocellulosic material, which are: physical (grinding and extrusion, among others); chemical (acids and alkaline); thermochemical (pyrolysis); ionic liquid (salts); and biological (microorganism) to improve biofuel production. The use of CPH as a substrate in bioconversion processes is a viable and promising option, despite the limitations of each pretreatment method.

A review on recent developments in hydrodynamic cavitation and advanced oxidative processes for pretreatment of lignocellulosic materials

Environmental problems due to utilization of fossil-derived materials for energy and chemical generation has prompted the use of renewable alternative sources, such as lignocellulose biomass (LB). Indeed, the production of biomolecules and biofuels from LB is among the most important current research topics aiming to development a sustainable bioeconomy. Yet, the industrial use of LB is limited by the recalcitrance of biomass, which impairs the hydrolysis of the carbohydrate fractions. Hydrodynamic cavitation (HC) and Advanced Oxidative Processes (AOPs) has been proposed as innovative pretreatment strategies aiming to reduce process time and chemical inputs. Therefore, the underlying mechanisms, procedural strategies, influence on biomass structure, and research gaps were critically discussed in this review. The performed discussion can contribute to future developments, giving a wide overview of the main involved aspects.

The production of laccases by white-rot fungi under solid-state fermentation conditions

Laccases (E.C. 1.10.3.2) produced by white-rot fungi (WRF) can be widely used, but the high cost prevents their use in large-scale industrial processes. Finding a solution to the problem could involve laccase production by solid-state fermentation (SSF) simulating the natural growth conditions for WRF. SSF offers several advantages over conventional submerged fermentation (SmF), such as higher efficiency and productivity of the process and pollution reduction. The aim of this review is therefore to provide an overview of the current state of knowledge about the laccase production by WRF under SSF conditions. The focus is on variations in the up-stream process, fermentation and down-stream process and their impact on laccase activity. The variations of up-stream processing involve inoculum preparation, inoculation of the medium and formulation of the propagation and production media. According to the studies, the production process can be shortened to 5-7 days by the selection of a suitable combination of lignocellulosic material and laccase producer without the need for any additional components of the culture medium. Efficient laccase production was achieved by valorisation of wastes as agro-food, municipal wastes or waste generated from wood processing industries. This leads to a reduction of costs and an increase in competitiveness compared to other commonly used methods and/or procedures. There will be significant challenges and opportunities in the future, where SSF could become more efficient and bring the enzyme production to a higher level, especially in new biorefineries, bioreactors and biomolecular/genetic engineering.

Bibliometric analysis of global research on white rot fungi biotechnology for environmental application

In recent years, white rot fungi (WRFs) have received tremendous attention as a biotechnological tool for environmental pollution control. In order to systematically and comprehensively describe the progress, trends, and hotspots of WRF biotechnology in the field of environmental pollution control, the 3967 related publications from 2003 to 2020 were collected from Web of Science Core Collection database, and the bibliometric characteristics including publication output, country, institution, journal, author, citation frequency, h-index, and research focus were evaluated by using Excel 2007, CiteSpace V, and VOSviewer. The results indicated that the number of research publications increased rapidly before 2009, but after that, the number of publications fluctuated in a certain range. China and USA were the most productive countries and the most active country in international cooperation. In this field, most authors tend to cooperate within a small group. The journal and subject category with the largest number of publications are "International Biodeterioration & Biodegradation" and "Biotechnology Applied Microbiology", respectively. The analysis of high-frequency keywords revealed that "laccase", "biodegradation", "decolorization", and "Phanerochaete chrysosporium" were the most cited terms among all publications. The pretreatment of biomass waste, decolorization of dye wastewater, and bioremediation of polluted environment are the key research directions of WRF biotechnology. Finally, the frontier topics and active authors in this research field were identified using burst detection. We believe that this bibliometric study provides a comprehensive and systematic overview and promoted the future cooperative research and knowledge exchange in this field of WRF biotechnology for environmental applications.

Fiber degradation and carbohydrate production by combined biological and chemical/physicochemical pretreatment methods of lignocellulosic biomass - A review

Sustainable biorefinery concepts based on lignocellulosic biomass are gaining worldwide research interest because of their inexpensiveness and abundance. The recalcitrance of lignocellulosic biomass poses a major hindrance to enhance biofuel production. Therefore, a pretreatment step is critical to prepare the substrates for the downstream process. Combining pretreatment steps help to lower the severity of the drawbacks of a single pretreatment step. This paper systematically reviews the combined biological and chemical/physicochemical pretreatment based on fiber degradation and sugar yield. An energy-efficient biological pretreatment method combined with a chemical pretreatment that accelerates the pretreatment times has been seen to be efficient for fiber degradation and sugar yields. However, fungal species, culture conditions, biomass type, the severity of chemical pretreatment and the order of sequential pretreatment influences the relative component contents and sugar yield. Even the same biomass from different sources undergoing similar pretreatment conditions could result in a varying amount of digestibility.

Recent Advancements in Biological Conversion of Industrial Hemp for Biofuel and Value-Added Products

Sustainable, economically feasible, and green resources for energy and chemical products have people’s attention due to global energy demand and environmental issues. Last several decades, diverse lignocellulosic biomass has been studied for the production of biofuels and biochemicals. Industrial hemp has great market potential with its versatile applications. With the increase of the hemp-related markets with hemp seed, hemp oil, and fiber, the importance of hemp biomass utilization has also been emphasized in recent studies. Biological conversions of industrial hemp into bioethanol and other biochemicals have been introduced to address the aforementioned energy and environmental challenges. Its high cellulose content and the increased production because of the demand for cannabidiol oil and hempseed products make it a promising future bioenergy and biochemical source. Effective valorization of the underutilized hemp biomass can also improve the cost-competitiveness of hemp products. This manuscript reviews recent biological conversion strategies for industrial hemp and its characteristics. Current understanding of the industrial hemp properties and applied conversion technologies are briefly summarized. In addition, challenges and future perspectives of the biological conversion with industrial hemp are discussed.

Mapping the Secretome and Its N-Linked Glycosylation of Pleurotus eryngii and Pleurotus ostreatus Grown on Hemp Stalks

Our previous research showed that Pleurotus eryngii and Pleurotus ostreatus were effective fungi for pretreatment of industrial hemp stalks to improve enzymatic saccharification. The secretomes of these two fungi were analyzed to search for the effective enzyme cocktails degrading hemp lignin during the pretreatment process. In total, 169 and 155 proteins were identified in Pleurotus eryngii and Pleurotus ostreatus, respectively, and 50% of the proteins involved in lignocellulose degradation were CAZymes. Because most of the extracellular proteins secreted by fungi are glycosylated proteins, the N-linked glycosylation of enzymes could be mapped. In total, 27 and 24 N-glycosylated peptides were detected in Pleurotus eryngii and Pleurotus ostreatus secretomes, respectively. N-Glycosylated peptides of laccase, GH92, exoglucanase, phenol oxidase, α-galactosidase, carboxylic ester hydrolase, and pectin lyase were identified. Deglycosylation could decrease enzymatic saccharification of hemp stalks. The activities of laccase, α-galactosidase, and phenol oxidase and the thermal stability of laccase were reduced after deglycosylation.

Lignin Degradation Efficiency of Chemical Pre-Treatments on Banana Rachis Destined to Bioethanol Production

Valuable biomass conversion processes are highly dependent on the use of effective pretreatments for lignocellulose degradation and enzymes for saccharification. Among the nowadays available treatments, chemical delignification represents a promising alternative to physical-mechanical treatments. Banana is one of the most important fruit crops around the world. After harvesting, it generates large amounts of rachis, a lignocellulosic residue, that could be used for second generation ethanol production, via saccharification and fermentation. In the present study, eight chemical pretreatments for lignin degradation (organosolv based on organic solvents, sodium hypochlorite, hypochlorous acid, hydrogen peroxide, alkaline hydrogen peroxide, and some combinations thereof) have been tested on banana rachis and the effects evaluated in terms of lignin removal, material losses, and chemical composition of pretreated material. Pretreatment based on lignin oxidation have demonstrated to reach the highest delignification yield, also in terms of monosaccharides recovery. In fact, all the delignified samples were then saccharified with enzymes (cellulase and beta-glucosidase) and hydrolysis efficiency was evaluated in terms of final sugars recovery before fermentation. Analysis of Fourier transform infrared spectra (FTIR) has been carried out on treated samples, in order to better understand the structural effects of delignification on lignocellulose. Active chlorine oxidations, hypochlorous acid in particular, were the best effective for lignin removal obtaining in the meanwhile the most promising cellulose-to-glucose conversion.

Sequential white-rot and brown-rot fungal pretreatment of wheat straw as a promising alternative for complementary mild treatments

White-rot and brown-rot fungi have complementary mechanisms to selectively degrade lignin and holocellullose, respectively. Thereby, a fungal co-culture of a white-rot and a brown-rot fungal could result in efficient strategy for a mild lignocellulosic biomass pretreatment. In this work, single, sequential and co-inoculation of the selective-lignin degrading white-rot fungus Ganoderma lobatum and the brown-rot fungus Gloeophyllum trabeum were evaluated as biological pretreatments of wheat straw to enhance enzymatic hydrolysis of cellulose. The single cultures of G. lobatum and G. trabeum exhibited preferential degradation of lignin and hemicellulose, respectively. The total crystallinity index decreased in samples pretreated with G. trabeum but not with G. lobatum. The pretreatment with single cultures of G. lobatum or G. trabeum increased glucose yields by 43.6% and 26.1% respectively compared to untreated straw. Although co-inoculation resulted in higher yields of glucose when compared with single cultures, only a slight synergistic effect between fungi was observed. Contrary, the sequential inoculation of G. lobatum incubated for 10 days followed by G. trabeum incubated for 10 days more showed a strong synergic effect on enzymatic hydrolysis. This sequential culture showed the highest glucose yield (191.5 mg g^-1 wheat straw), 2.8-fold higher than untreated wheat straw, and 140-150% higher than the single-cultures of G. lobatum and G. trabeum, respectively.

Enhanced bioreduction synthesis of ethyl (R)-4-chloro-3-hydroybutanoate by alkalic salt pretreatment

In this study, biomass-hydrolysate was used for enhancing the bioreduction of ethyl 4-chloro-3-oxobutanoate (COBE). Firstly, dilute alkalic salt pretreatment was attempted to pretreat bamboo shoot shell (BSS). It was found that enzymatic in situ hydrolysis of 20-50 g/L BSS pretreated with dilute alkalic salts (0.4% Na₂CO₃, 0.032% Na₂S) at 7.5% sulfidity by autoclaving at 110 °C for 40 min gave sugar yields at 59.9%-73.5%. Moreover, linear relationships were corrected on solid recovery-total delignification-sugar yield. In BSS-hydrolysates, xylose and glucose could promote the reductase activity of recombinant E. coli CCZU-A13. Compared with glucose, hydrolysate could increase the reductase activity by 1.35-folds. Furthermore, the cyclohexane-hydrolysate (10:90, v/v) biphasic media containing ethylene diamine tetraacetic acid (EDTA, 40 mM) and l-glutamine (150 mM) was built for the effective biosynthesis of ethyl (R)-4-chloro-3-hydroxybutanoate [(R)-CHBE] (94.6% yield) from 500 mM COBE. In conclusion, this strategy has high potential for the effective biosynthesis of (R)-CHBE (>99% e.e.).