Denitrification performance and microbial diversity of immobilized bacterial consortium treating nitrate micro-polluted water

Effect of hydraulic residence time on nitrogen removal from a synthetic mariculture wastewater using a bench-scale recirculating bioreactor embedded with aerobic denitrifying bacteria Marinobacter alkaliphilus strain JY28

Beads loaded with tea dregs powder and immobilized aerobic denitrifying bacteria (Marinobacter alkaliphilus strain JY28) were prepared by cross-linking sodium alginate and polyvinyl alcohol. The beads were subsequently utilized for nitrogen removal in treatment of wastewater from a marine recirculating aquaculture system (MRAS). The effects of hydraulic residence time (HRT) on nitrogen removal efficiency, microbial community succession, and the physicochemical properties and kinetic behaviors of the immobilized bacterial beads were investigated. The results indicated that the highest NO3--N removal rate was 99.4 ± 0.6 % at an HRT of 10 h, while the cumulative NO2--N concentration remained at its lowest level (0.04 ± 0.05 mg L-1). Furthermore, the peak maximum specific nitrogen removal rates (μmax) for NO3--N and NO2--N were found to be 16.12 mg L-1·h-1 and 8.61 mg L-1·h-1, respectively. The surface of the immobilized bacterial beads was rough and effectively bound Marinobacter alkaliphilus strain JY28. The interior of the beads possessed an irregular honeycomb-like and porous structure, favorable for the immobilization and proliferation of Marinobacter alkaliphilus strain JY28. The presence of the ring structure in the functional bonds enhanced both the mechanical strength and the immobilized bacterial beads stability. Marinobacter alkaliphilus strain JY28 was retained in the bacterial beads and consistently maintained its dominance during the whole experimental process. The results lay a theoretical foundation for application of immobilized bacterial beads for highly efficient nitrogen removal in MRAS wastewater treatment.

Coupling of titanium dioxide loaded carrier and denitrification biofilm for the advanced treatment of micro-polluted water

TiO2 was immobilized on a polypropylene polyhedral (PP) ball using polyamide (PA) hot melt adhesive to generate floating photocatalyst TiO2-PA/PP with high photocatalytic activity, which was further coupled with denitrification biofilm to form TiO2-PA/PP biofilm system. The analysis of SEM, EDS, XRD, and FTIR confirmed that TiO2 was immobilized on the surface of PP without any changes in the crystal structure of TiO2. The photocatalytic experiments showed that the degradation efficiencies of p-phenylenediamine, sucrose, humic acid, and bovine albumin by TiO2-PA/PP were 58.3%, 48.0%, 97.1%, and 66.6%, respectively. •O2- and h+ were the key reactive oxygen species (ROSs) in photocatalytic degradation of organic matter in the TiO2-PA/PP system under solar irradiation. In the synthetic water, 95.5% humic acid and 43.2% nitrate were simultaneously removed in TiO2-PA/PP biofilm reactor, confirming the coupling of photocatalytic degradation and denitrification. In the actual micro-polluted surface water, the coupling photocatalytic and biofilm reactor reduced chemical oxygen demand (COD) by 68.4% and nitrate by 38.9% in 480 min. This study provided a new option for the in-situ removal of organic matter and nitrate from micro-polluted surface water.

Optimizing nitrogen removal in advanced wastewater treatment using biological aerated filters

Reducing total nitrogen (TN) presents a significant challenge for numerous wastewater treatment facilities. In order to address this issue, the current study employed a biological aerated filter for the treatment of wastewater containing low nitrogen concentrations. Both lab-scale and pilot-scale biofilters were constructed to investigate the denitrification performance and maximum denitrification load. The findings indicated that the anaerobic denitrification process of established biofilm adhered to pseudo-first-order kinetics. The results of batch testing and continuous-flow experiments confirmed that the minimum hydraulic retention time (HRT) required for mature biofilm was determined to be 0.5 h. The optimal operating parameters were found to be as follows: influent NO3 --N concentration of 25 mg/L, HRT of 0.5 h, resulting in effluent TN levels below 1 mg/L. Under these conditions, the denitrifying load for the lab-scale I-BAF system was calculated to be 1.26 kg (TN)/(m3·d). Furthermore, it was observed that the maximum denitrifying load could reach 2.2 kg (TN)/(m3·d) when the influent NO3 --N concentration was increased to 50 mg/L while maintaining an HRT of 0.5 h. For the mature biofilter, the appropriate HRT ranged from 2 h to 0.5 h. Microbial diversity analysis revealed that the genus Enterobacter was dominant in all denitrification systems, followed by Comamonas and Rhodococcus. The operational parameters described in the paper could be recommended for a full-scale wastewater treatment facility.

3D printing for constructing biocarriers using sodium alginate/ε-poly-l-lysine ink: Enhancing microbial enrichment for efficient nitrogen removal in wastewater

The microbial enrichment of traditional biocarriers is limited due to the inadequate consideration of spatial structure and surface charging characteristics. Here, capitalizing on the ability of 3D printing technology to fabricate high-resolution materials, we further designed a positively charged sodium alginate/ε-poly-l-lysine (SA/ε-PL) printing ink, and the 3D printed biocarriers with ideal pore structure and rich positive charge were constructed to enhance the microbial enrichment. The rheological and mechanical tests confirmed that the developed SA/ε-PL ink could simultaneously satisfy the smooth extrusion for printing process and the maintenance of 3D structure. The utilization of the ε-PL secondary cross-linking strategy reinforced the 3D mechanical structure and imparted the requisite physical properties for its application as a biocarrier. Compared with traditional sponge carriers, 3D printed biocarrier had a faster initial attachment rate and a higher biomass of 14.58 ± 1.18 VS/cm3, and the nitrogen removal efficiency increased by 53.9 %. Besides, due to the superior electrochemical properties and biocompatibility, the 3D printed biocarriers effectively enriched the electroactive denitrifying bacteria genus Trichococcus, thus supporting its excellent denitrification performance. This study provided novel insights into the development of new functional biocarriers in the wastewater treatment, thereby providing scientific guidance for practical engineering.

Preparation of Newly Polymer-Coated Microbial Pellets and Their Adsorption and Degradation Properties for Oil-Containing Wastewater

Water is the lifeblood of everything on earth, nourishing and nurturing all forms of life, while also contributing to the development of civilization. However, with the rapid development of economic construction, especially the accelerated process of modern industrialization, the pollution of oily sewage is becoming increasingly serious, affecting the ecological balance and human health. The efficient elimination of pollutants in sewage is, therefore, particularly urgent. In this paper, a core-shell microbial reactor (MPFA@CNF-SA-AM) was fabricated by using nanocellulose and sodium alginate (SA) particles embedded with microorganisms as the core and lipophilic and hydrophobic fly ash as the outer shell layer. Compared with that of free microorganisms and cellulose and SA aerogel pellets loading with microorganisms (CNF-SA-AM), which has a degradation efficiency of 60.69 and 82.89%, respectively, the MPFA@CNF-SA-AM possesses a highest degradation efficiency of 90.60% within 240 h. So that this self-floating microbial reactor has selective adsorption properties to achieve oil-water separation in oily wastewater and high effective degradation of organic pollutants with low cost. The adsorption curves of MPFA@CNF-SA-AM for diesel and n-hexadecane were studied. The results showed that the adsorption follows the Freundlich model and is a multimolecular layer of physical adsorption. In addition, the degradation mechanism of diesel oil was studied by gas chromatography-mass spectrometry. The results showed that diesel oil was selectively adsorbed to the interior of MPFA@CNF-SA-AM, and it was degraded by enzymes in microorganisms into n-hexadecanol, n-hexadecaldehyde, and n-hexadecanoic acid in turn, and finally converted to water and carbon dioxide. Compared with existing oily wastewater treatment methods, this green and pollution-free dual-functional core-shell microbial reactor has the characteristics of easy preparation, high efficiency, flexibility, and large-scale degradation. It provides a new, effective green choice for oily wastewater purification and on-site oil spill accidents.

Enhancement of bio-promoters on hexavalent chromium inhibited sulfur-driven denitrification: repairing damage, accelerating electron transfer, and reshaping microbial collaboration

Proposing recovery strategies to recover heavy-metal-inhibited sulfur-driven denitrification, as well as disclosing recovery mechanisms, can provide technical support for the stable operation of bio-systems. This study proposed an effective bio-promoter (mediator-promoter composed of L-cysteine, biotin, cytokinin, and anthraquinone-2,6-disulfonate) to recover Cr(VI) inhibited sulfur-driven denitrification, which effectively reduced the recovery time of NO3--N reduction (18-21 cycles) and NO2--N reduction (27-42 cycles) compared with self-recovery. The mediator-promoter repaired microbial damage by promoting intracellular chromium efflux. Moreover, the mediator-promoter reduced the accumulated reactive oxygen species by stimulating the secretion of antioxidant enzymes, reaching equilibrium in the oxidative-antioxidant system. To improve electron transmission, the mediator-promoter restored S2O32- oxidation to provide adequate electron donors and increased electron transfer rate by increasing cytochrome c levels. Mediator-promoter boosted the abundance of Thiobacillus (sulfur-oxidizing bacterium) and Simplicispira (denitrifying bacterium), which were positively correlated, facilitating the rapid denitrification recovery and the long-term stable operation of recovered systems.

Controlling carbon dioxide-to-hydrogen ratio to improve hydrogen utilization and denitrification rates of hydrogenotrophic autotrophic denitrification through homoacetogenesis-heterotrophic denitrification pathway

Hydrogenotrophic denitrification, an environment-friendly process for organic-free influents, is limited due to poor hydrogen mass transfer efficiency and significant pH fluctuations. In this study, we manipulated the carbon dioxide-to-hydrogen ratio to improve hydrogenotrophic denitrification. When carbon dioxide-to-hydrogen ratio was 1:1 (carbon dioxide, 200 ml: hydrogen, 200 ml), the hydrogen utilization and denitrification rates were 2.4 times and 3.0 times that when carbon dioxide-to-hydrogen ratio was 0:1 (carbon dioxide, 0 ml: hydrogen, 200 ml), respectively. The pH fluctuation decreased from 3.1±0.3 to 0.2±0.1. Furthermore, the hydrogenotrophic denitrification, acetoclastic denitrification, homoacetogenic, and electron transfer activities of the sludge were improved. A high carbon dioxide-to-hydrogen ratio augmented the acid-producing and heterotrophic denitrifying microorganism populations. By maintaining a high carbon dioxide-to-hydrogen ratio, the dominant hydrogenotrophic autotrophic denitrification pathway was transformed into a homoacetogenesis-heterotrophic denitrification pathway, thereby achieving higher hydrogen utilization and denitrification rates.

More effective application of biochar-based immobilization technology in the environment: Understanding the role of biochar

In recent years, biochar-based immobilization technology (BIT) has been widely used to treat different environmental issues because of its cost-effectiveness and high removal performance. However, the complexity of the real environment is always ignored, which hinders the transfer of the BIT from lab-scale to commercial applications. Therefore, in this review, the analysis is performed separately on the internal side of the BIT (microbial fixation and growth) and on the external side of the BIT (function) to achieve effective BIT performance. Importantly, the internal two stages of BIT have been discussed concisely. Further, the usage of BIT in different areas is summarized precisely. Notably, the key impacts were systemically analyzed during BIT applications including environmental conditions and biochar types. Finally, the suggestions and perspectives are elucidated to solve current issues regarding BIT.

Treatment of micro-polluted water with low C/N ratio by immobilized bioreactor using PVA/sintered ores@sponge cube: Performance effects and potential removal pathways

The widespread use of industrial products containing lead (Pb²⁺) and tetracycline (TC) medications led to the combined pollution of nitrate, Pb²⁺, and TC in water. A novel biomaterial containing polyvinyl alcohol (PVA) and sponge cube with sintered ores (PVA/sintered ores@sponge cube) was prepared to ensure the maximum NO₃^--N removal efficiency (96.21 %) of the bioreactor under the hydraulic retention time (HRT) of 7.0 h, pH of 6.0, and the carbon to nitrogen (C/N) of 1.5 that had the ability to remove TC and Pb²⁺ synergistically. Composite pollutants slightly decreased denitrification performance in the combined pollution system on account of the addition of sintered ores. Results of scanning electron microscopy (SEM) showed that the sintered ores in the biocarrier induced denitrification and the adsorption of bio‑iron oxides were involved in the removal of TC and Pb²⁺. The simultaneous removal of composite pollutants during denitrification was facilitated by extracellular polymeric substances (EPS) as revealed by Fourier transform infrared spectroscopy (FTIR) and fluorescence excitation-emission matrix (EEM). In addition, high-throughput sequencing results showed that Zoogloea had the highest proportion in the bioreactor.

Simultaneous removal of nitrate, lead, and tetracycline by a fixed-biofilm reactor assembled with kapok fiber and sponge iron: Comparative analysis of operating conditions and biotic community

In recent years, under the condition of lack of carbon source, the presence of composite micro-pollutants make the removal of nitrate seriously damaged, and to find a suitable way to solve this problem is imminent. A fixed-biofilm carrier modified by mixing sponge iron (SI) and kapok fiber (KF) combined with strain Zoogloea sp. FY6 was constructed in this study to get a fixed-biofilm reactor with merit denitrification performance. By adjusting the operation parameters, it can be concluded that when the carbon to nitrogen (C/N) ratio was 1.5, the hydraulic retention time (HRT) was 6.0 h, and the pH was 6.0, the nitrate removal efficiency (NRE) of the fixed-biofilm reactor was up to 95.4% (2.95 mg L^-1 h^-1). In addition, the fixed-biofilm reactor constructed in this study can remove lead (Pb²⁺) and tetracycline (TC) excellently in the presence of SI and Zoogloea sp. FY6, and the denitrification performance can still maintain a high level under the influence of different concentrations of Pb²⁺ and TC. Furthermore, the addition of SI not only removes the compound pollutants, but also protects the toxicity of the pollutant inflow in the bioreactor, and the metabolic process of microorganisms in the bioreactor also removes some of the compound pollutants. The high-throughput data showed the abundance of strain Zoogloea sp. FY6 was still the highest value under the influence of various pollutants, and the metagenomic prediction showed that the fixed-biofilm reactor had perfect denitrification process and iron redox cycle benefits. This study provides a valuable reference for sustainable utilization of natural biological resources and reduction of material costs in wastewater treatment plants (WWTPs).

A review: Manganese-driven bioprocess for simultaneous removal of nitrogen and organic contaminants from polluted waters

Water pollutants, such as nitrate and organics have received much attention for their harms to ecological environment and human health. The redox transformation between Mn(Ⅱ) and Mn(Ⅳ) for nitrogen and organics removal have been recognized for a long time. Mn(Ⅱ) can act as inorganic electron donor to drive autotrophic denitrification so as to realize simultaneous removal of Mn(Ⅱ), nitrate and organic pollutants. Mn oxides (MnOx) also play an important role in the adsorption and degradation of some organic contaminants and they can change or create new oxidation pathways in the nitrogen cycle. Herein, this paper provides a comprehensive review of nitrogen and organic contaminants removal pathways through applying Mn(Ⅱ) or MnOx as forerunners. The main current knowledge, developments and applications, pollutants removal efficiency, as well as microbiology and biochemistry mechanisms are summarized. Also reviewed the effects of factors such as the carbon source, the environmental factors and operation conditions have on the process. Research gaps and application potential are further proposed and discussed. Overall, Mn-based biotechnology towards advanced wastewater treatment has a promising prospect, which can achieve simultaneous removal of nitrogen and organic contaminants, and minimize sludge production.

Efficient nitrate removal of immobilized mixed aerobic denitrifying bacteria and community dynamics response to temperature and low carbon/nitrogen polluted water

The denitrification performance of immobilized mixed aerobic denitrifying bacteria (IMADB) was investigated. IMADB displayed strong temperature adaptability under low Carbon/Nitrogen conditions. At 5, 15, and 25 °C, the nitrate removal efficiencies of volcanic rock and polyester fiber sponge immobilized system reached 83.95%-98.25% and 89.71%-98.14%, respectively. The nitrate content removed by the carrier accounted for 41.18%-82.47% of the nitrate content removed by the immobilized system at different temperature, and played a major role in nitrate removal. The lower the temperature, the greater the role of the carrier. At the same temperature, carrier had a relatively higher richness, diversity, and evenness. Network analysis revealed that carrier species, which were positively correlated with nitrate removal efficiency, had the largest OTUs and abundance. Meanwhile, carrier had the widest niche. The total nitrogen removal efficiency of IMADB reached 56.10%-62.31% in the natural water system, highlighting a promising application prospect.

Mix-cultured aerobic denitrifying bacteria augmented carbon and nitrogen removal for micro-polluted water: Metabolic activity, coexistence and interactions, and immobilized bacteria for reservoir raw water treatment

Less attention has been paid on the oligotrophic water body nitrogen treatment with mix-cultured aerobic denitrifying bacteria (Mix-CADB). In this study, three Mix-CADB communities were screened from the sediments of reservoirs. The nitrate and dissolved organic carbon (DOC) removal efficiencies of Mix-CADB communities were higher than 92 % and 91 %, respectively. Biolog results suggested that Mix-CADB communities displayed excellent carbon source metabolic activity. The nirS gene sequencing indicated that Pseudomonas sp. and Pseudomonas stutzeri accounted for more proportions in the core species of three Mix-CADB communities. The network model revealed that Pseudomonas sp. and Pseudomonas stutzeri mainly drove the total nitrogen and DOC removal of Mix-CADB communities. More importantly, the immobilized Mix-CADB communities could reduce >91 % nitrate in the adjusted reservoir raw water. Overall, this study showed that the three Mix-CADB communities could be regarded as potential candidates for the nitrogen treatment in oligotrophic water body ecosystems.

Impacts of engineered nanoparticles and antibiotics on denitrification: Element cycling functional genes and antibiotic resistance genes

The wide presence of antibiotics and minerals warrants their combined effects on the denitrification in natural aquatic environment. Herein, we investigated the effects of two antibiotics, sulfamethazine (SMZ) and chlortetracycline (CTC), on the reduction of NO₃^--N and accumulation of NO₂^--N in the absence and presence of engineered nanoparticles (NPs) (Al₂O₃, SiO₂, and geothite) using 16 S rRNA sequencing and high-throughput quantitative PCR. The results showed that the addition of antibiotics inhibited the reduction of NO₃^--N by changing the bacterial community structure and reducing the abundance of denitrification genes, while engineered NPs promoted the denitrification by increasing the abundance of denitrification genes. In the binary systems, engineered NPs alleviated the inhibitory effect of antibiotics through enriching the denitrification genes and adsorbing antibiotics. Antibiotics and its combination with engineered NPs changed the composition of functional genes related to C, N, P, S metabolisms (p < 0.01). The addition of antibiotics and/or engineered NPs altered the bacterial community structure, which is dominated by the genera of Enterobacter (40.7-90.5%), Bacillus (4.9-58.5%), and Pseudomonas (0.21-12.7%). The significant relationship between denitrification, carbon metabolism genes, and antibiotic resistance genes revealed that the heterotrophic denitrifying bacteria may host the antibiotic resistance genes and denitrification genes simultaneously. The findings underscore the significance of engineered NPs in the toxicity assessment of pollutants, and provide a more realistic insight into the toxicity of antibiotics in the natural aquatic environment.

Rice washing drainage (RWD) embedded in poly(vinyl alcohol)/sodium alginate as denitrification inoculum for high nitrate removal rate with low biodiversity

Immobilization technology with low maintenance is a promising alternative to enhance nitrate removal from water. In this study, washing rice drainage (RWD) was immobilized by poly(vinyl alcohol)/sodium alginate (PVA/SA) to obtain RWD-PVA/SA gel beads as inoculum for denitrification. When initial nitrate concentration was 50 mg N/L, nitrate was effectively removed at rates of 50-600 mg/(L∙d) using acetate as carbon source (C/N = 1.25). Arrhenius activation energy (Ea) of nitrate oxidoreductase was 28.64 kJ/mol for the RWD-PVA/SA gel beads. Temporal and spatial variation in microbial community structures were revealed along with RWD storage and in the reactors by Illumina high-throughput sequencing technology. RWD-PVA/SA gel beads has a simple (operational taxonomic units (OTUs) 〈100). Dechloromonas, Pseudomonas, Flavobacterium and Acidovorax were the most four dominant genera in the denitrification reactors inoculated with RWD-PVA/SA gel beads. This study provides an inoculum for denitrification with high nitrate removal performance and simple microbial community structures.

Response of immobilized denitrifying bacterial consortium to tetracycline exposure

Tetracycline (TC) as one of the most widely used antibiotics commonly exists in aquaculture tail water and piggery wastewater, causing risks to human. However, the response of immobilized anaerobic denitrifying bacterial consortium to TC exposure lacks systematic research. In this study, the denitrification performance and the compositional shift of extracellular polymeric substances (EPS) and microbial community under TC stress were investigated. The inhabitation effect of TC on nitrate reduction of the immobilized bacterial consortium became evident at high concentrations (50 mg/L and 100 mg/L). Nitrite reduction was more sensitively inhibited than nitrate reduction. The inhabitation effect was mainly due to the fact that TC damaged cell membranes and subsequently effect the intracellular enzymes activities relating to denitrification (NAR and NIR activities). About 50% of TC can be removed by the immobilized bacterial consortium under all tested TC concentrations. Three-dimensional excitation-emission matrix (3D-EEM) results implied that the tryptophan like substances of EPS were obviously quenched with increasing TC concentration. EPS played an important role in TC removal. The denitification performance of the immobilized bacterial consortium under TC stress was attributed to the genera Paraccoccus, Pseudoxanthomonas, Diaphorobacter and Pseudomonas. Initial TC concentration obviously affected the microbial communities. This study may facilitate the management of aquaculture tail water and piggery wastewater contaminated with nitrate and antibiotics.

Effectiveness of agricultural waste in the enhancement of biological denitrification of aquaculture wastewater

Nitrogen pollution in aquaculture wastewater can pose a significant health and environmental risk if not removed before wastewater is discharged. Biological denitrification uses external carbon sources to remove nitrogen from wastewater; however, these carbon sources are often expensive and require significant energy. In this study, we investigated how six types of agricultural waste can be used as solid carbon sources in biological denitrification. Banana stalk (BS), loofah sponge (LS), sorghum stalk (SS), sweet potato stalk (SPS), watermelon skins (WS) and wheat husk (WH) were studied to determine their capacity to release carbon and improve denitrification efficiency. The results of batch experiments showed that all six agricultural wastes had excellent carbon release capacities, with cumulative chemical oxygen demands of 37.74-535.68 mg/g. During the 168-h reaction, the carbon release process followed the second-order kinetic equation and Ritger-Peppas equation, while carbon release occurred via diffusion. The kinetic equation fitting, scanning electron microscopy, and Fourier transform infrared spectroscopy results showed that LS had the lowest c_m and the maximum t_1/2 values and only suffered a moderate degree of hydrolysis. It also had the lowest pollutant release rate and cumulative chemical oxygen demand, as well as the most efficient removal of total phosphorous (TP) and total nitrogen (TN). Therefore, we concluded that LS has the lowest potential risk of excess carbon release and capacity for long-lasting and stable carbon release. The WS leachate had the highest TN contents, while the SPS leachate had the highest TP content. In the 181-h denitrification reaction, all six agricultural wastes completely removed nitrate and nitrite; however, SS had the highest denitrification rate, followed by LS, WH, BS, SPS, and WS (2.16, 1.35, 1.35, 1.34, 1.34, and 1.01 mg/(L·h), respectively). The denitrification process followed a zero-order and first-order kinetic equation. These results provide theoretical guidance for effectively selecting agricultural waste as a solid carbon source and improving the denitrification efficiency of aquaculture wastewater treatment.

Mixotrophic denitrification for enhancing nitrogen removal of municipal tailwater: Contribution of heterotrophic/sulfur autotrophic denitrification and bacterial community

The heterotrophic and autotrophic denitrification system can be used to remove wastewater nitrogen effectively. However, the relationship between nitrogen removal performance and microbial community composition variation needs to be explored further. Therefore, a combined heterotrophic‑sulfur autotrophic biofilter (HSAD) was established to remove nitrogen from municipal tailwater. As methanol dosage increased from 12 mg/L to 36 mg/L, NO₃^--N removal efficiency increased from 86.1% to 98.9%, and the generation of SO₄^2- in the effluent was controlled within 167.6-113.2 mg/L under the condition of 30 mg/L NO₃^--N in influent and 3 h hydraulic retention time. Increasing methanol dosage promoted the synergism of heterotrophic denitrification (HD) and sulfur autotrophic denitrification (SAD). Different denitrification performance was associated with the microbial community composition. Proteobacteria, Bacteroidetes, and Chloroflexi were major phyla with cumulative abundance of over 70% and Proteobacteria was predominate in all samples. Denitrifying bacteria, such as Ferritrophicum, Thiobacillus, Thauera and Comamonas dominated in different operation stages of mixotrophic reactor. The decrease in dominant HD bacteria accompanied with the increase in SAD bacteria, and the SAD bacterial richness declined with the rise of HD contribution in the total denitrification process. Correlation networks analysis indicated that the dominant bacteria had positive or negative correlation with each other, but a stable coexistence state of microbial community structure was formed under the mixotrophic conditions. This work deepens our understanding of HSAD and reveals the interconnection between nitrogen removal mechanism and microbial community composition variation.

Mixed Effects of Soil Compaction on the Nitrogen Cycle Under Pea and Wheat

Soil compaction caused by highly mechanized agriculture can constrain soil microbial diversity and functioning. Physical pressure on the soil decreases macropores and thereby limits oxygen diffusion. The associated shift from aerobic to anaerobic conditions can reduce nitrification and promote denitrification processes, leading to nitrogen (N) losses and N depletion that affect plant productivity. High soil moisture content during trafficking can exacerbate the negative effects of soil compaction. However, the extent to which soil moisture amplifies the effects of compaction on the soil microbiome and its control over N cycling is not well understood. Using a controlled greenhouse experiment with two different crops (pea and wheat), we compared the effects of compaction at three different soil moisture levels on soil physicochemical properties, microbial diversity, and the abundance of specific N species and quantification of associated microbial functional groups in the N cycle. Soil compaction increased bulk density from 15% (light compaction) to 25% (severe compaction). Compaction delayed germination in both crops and reduced yield by up to 60% for pea and 40% for wheat. Compaction further induced crop-specific shifts in microbial community structures. After compaction, the relative abundance of denitrifiers increased along with increased nitrate (NO3 -) consumption and elevated nitrous oxide (N2O) concentrations in the soil pores. Conversely, the relative abundance of nitrifiers remained stable under compaction, but potentially decelerated nitrification rates, resulting in ammonium (NH4 +) accumulation in the soil. This study showed that soil compaction effects are proportional to the initial soil moisture content, which could serve as a good indicator of compaction severity on agricultural fields. However, the impact of soil compaction on crop performance and on microbial communities and functions associated with the N cycle were not necessarily aligned. These findings demonstrate that not only the soil physical properties but also various biological indicators need to be considered in order to provide more precise recommendations for developing sustainable farming systems.

Enhanced nitrate, manganese, and phenol removal by polyvinyl alcohol/sodium alginate with biochar gel beads immobilized bioreactor: Performance, mechanism, and bacterial diversity

Water pollutants, such as nitrate, heavy metals, and organics have attracted attention due to their harms to environmental and biological health. A novel polyvinyl alcohol/sodium alginate with biochar (PVA/SA@biochar) gel beads immobilized bioreactor was established to remove nitrate, manganese, and phenol. The optimum conditions for preparing gel beads were studied by response surface methodology (RSM). Notably, the removal efficiencies of nitrate, Mn(II), and phenol were 94.64, 72.74, and 93.97% at C/N of 2.0; the concentrations of Mn(II) and phenol were 20 and 1 mg L^-1, respectively. Moreover, addition of different concentrations of phenol significantly affected the components of dissolved organic matter, bacterial activity, and bioreactor performance. The biological manganese oxide (BMO) with three-dimensional petal-type structure produced during Mn(II) oxidation showed excellent adsorption capacity. The removal of phenol relied on a combination of biological action and adsorption processes. High-throughput analysis showed that Zoogloea sp. was the predominant bacterial group.

Denitrification performance and mechanism of denitrification biofilm reactor based on carbon-nitrate counter-diffusional

This study researched denitrification performance and mechanism of denitrification biofilm reactor with different HRTs and carbon sources dosages. Experimental group (EG) had better nitrate and COD removal performance than control group (CG) with different HRTs or carbon doses, and the maximum nitrate-to-nitrite transformation ratio (NTR) of them reached 7.91 ± 1.60% and 17.50 ± 1.92%, respectively. Because organic carbon sources were added to the carrier's interior in EG, forming high local concentrations in biofilms and counter-diffusional with nitrate. By contrast, carbon sources and nitrate were provided from the aqueous phase in CG. Thus, the EG system has more active regions of the biofilm than CG. In addition, EG had higher proportions of microorganisms and enzymes related to denitrification and carbon metabolism. The most dominant phylum, genus, and species were Proteobacteria, Thaurea, and Thauera_sp._27, respectively. The transcript of acetyl-CoA synthetase (K01895) and denitrification (M00529) was mainly originated from unclassified_g__Pseudomonas and unclassified_g__Thauera, respectively.

Treatment of dairy wastewater by immobilized microbial technology using polyurethane foam as carrier

The development of dairy industry is accompanied by large volumes of wastewater production, which is threaten to human's health and the biosphere. In this study, synthetic dairy wastewater was treated by immobilized microbial technology using polyurethane foam as carrier. Batch experiments were conducted to determine the effects of different operational parameters, and an up-flow immobilized microbial reactor was built to investigate long-term performance of the system. Batch experiments showed that COD, TN and NH₃-N dropped from 1932, 51.33 and 51.42 mg·L^-1 to 75.3, 5.17 and 4.54 mg·L^-1 after 48 h, respectively, at the optimum conditions (25 °C, pH 6.0). Besides, the reactor can remove 97.33% of COD, 96.46% of TN and 99.55% of NH₃-N with HRT of 24 h, which the average volume load was 1.93 kg COD·(m³·d)^-1. The analysis of microbial community determined that dominant bacteria at genus level were Acinetobacter, Fusibacter, Nannocystis and norank _f_NS9_marine_group.

Strategic management of nitrate pollution from contaminated water using viable adsorbents: An economic assessment-based review with possible policy suggestions

Groundwater contaminated with nitrate has prompted a flurry of research studies around the world in the recent years to address this burning environmental issue. The common presence of nitrates in groundwater, wastewater, and surface waters has thrown an enormously critical challenge to the global research communities to provide safe and clean drinking water to municipalities. As per WHO, the maximum permissible limit of nitrate in drinking water is 10 mg/L and in groundwater is 50 mg/L; exceeding the limits, several human health problems are observed. Adsorption, ion-exchange processes, membrane-based approaches, electrochemical and chemical procedures, biological methods, filtration, nanoparticles, etc. have been well investigated and reviewed to reduce nitrate levels in water samples in the recent years. Process conditions, as well as the efficacy of various approaches, were discovered to influence different techniques for nitrate mitigation. But, because of low cost, simple operation, easy handling, and high removal effectiveness, adsorption has been found to be the most suitable and efficient approach. The main objectives of this review primarily focuses on the creation of a naturally abundant, cost-effective innovative abundant material, such as activated clay particles combined with iron oxide. Oxide-clay nanocomposite materials, effectively remove nitrate with higher removal efficiency along with recovery of nitrate concentrated sludge. Such methods stand out as flexible and economic ways for capturing stabilized nitrate in solid matrices to satisfy long-term operations. A techno-economic assessment along with suitable policy suggestions have been reported to justify the viability of the brighter processes. Indeed, this kind of analytical review appears ideal for municipal community recommendations on abatement of excess nitrate to supply of clean water.

The performance of co-immobilized strains isolated from activated sludge combined with Scenedesmus quadricauda to remove nutrients and organics in black odorous water

In this study, three bacteria were isolated from activated sludge (Pseudomonas aeruginosa, Bacillus subtilis, and Dietzia maris). After that, isolated strains and Scenedesmus quadricauda that could degrade refractory organics, as co-immobilization species, were prepared gel beads to treat black odorous water. Under the optimized conditions, the removal rate of chemical oxygen demand (COD), ammonia nitrogen (NH₃-N), total nitrogen (TN) and total phosphorus (TP) reached 94.36%, 95.7%, 91.22% and 95.27%, respectively, and organics (including aromatic proteins and microbial-by-product-like compounds) were also significantly removed. Microbial analysis reveals that the community structure had a significant difference before and after treatment, and the main dominant at the genus level was transformed from Nitrospirillum (approximately 18.03%) to Flavobacterium (approximately 17.64%). This study also found that the immobilized gel beads have excellent stability and reusability, which provided a feasible and robust bioremediation strategy for the treatment of actual black-odor water.

How does partial substitution of chemical fertiliser with organic forms increase sustainability of agricultural production?

To ensure global food security, agriculture must increase productivity while reducing environmental impacts associated with chemical nitrogen (N) fertilisation. This necessitates towards more sustainable practices such as recycling organic waste to substitute chemical fertiliser N inputs. However, hitherto how such strategy controls the succession of microbial communities and their relationship with crop yields and environmental impacts have not been comprehensively investigated. We conducted a field experiment with vegetable production in China examining partial substitution (25-50%) of chemical fertiliser with organic forms (pig manure or municipal sludge compost) considering key sustainability metrics: productivity, soil health, environmental impacts and microbial communities. We demonstrate that partial organic substitution improved crop yields, prevented soil acidification and improved soil fertility. Treatments also reduced detrimental environmental impacts with lower N₂O emission, N leaching and runoff, likely due to reduced inorganic nitrogen surplus. Microbial communities, including key genes involved in the N cycle, were dynamic and time-dependent in response to partial organic substitution, and were also important in regulating crop yields and environmental impacts. Partial organic substitution increased bacterial diversity and the relative abundance of several specific microbial groups (e.g. Sphingomonadales, Myxococcales, Planctomycetes, and Rhizobiales) involved in N cycling. Additionally, partial organic substitution reduced the number of bacterial ammonia oxidizers and increased the number of denitrifiers, with the proportion of N₂O-reducers being more pronounced, suggesting a mechanism for reducing N₂O emissions. Comprehensive economic cost-benefit evaluation showed that partial organic substitution increased economic benefit per unit area by 37-46%, and reduced agricultural inputs and environmental impacts per unit product by 22-44%. Among them, 50% substitution of pig manure was the most profitable strategy. The study is crucial to policy-making as it highlights the potential advantages of shifting towards systems balancing chemical and organic fertilisers with economic benefits for farmers, reduced environmental damage and an efficient way for organic waste disposal.

Enhanced bioremediation of 2,3',4,4',5-pentachlorodiphenyl by consortium GYB1 immobilized on sodium alginate-biochar

2,3',4,4',5-pentachlorodiphenyl (PCB 118), a dioxin-like PCB, is often detected in the environment and is difficult to be aerobically biodegraded. In this study, a novel polychlorinated biphenyl degrading consortium GYB1 that can metabolize PCB 118 was successfully obtained by acclimatization process. To enhance the application performance of free bacterial cells, consortium GYB1 was immobilized with sodium alginate and biochar to prepare SC-GYB1 beads. Orthogonal experiments indicated that the optimal composition of the beads (0.2 g) was 2.0% sodium alginate (SA) content, 2.0% wet weight of cells and 1.5% biochar content, which can degrade 50.50% PCB 118 in 5 d. Immobilization shortened the degradation half-life of 1 mg/L PCB 118 by consortium GYB1 from 8.14 d to 3.79 d and made the beads more robust to respond to environmental stress. The SC-GYB1 beads could even keep considerable PCB degradation ability under 200 mg/L Cd²⁺ stress. According to 16S rRNA gene analysis, Pseudomonas and Stenotrophomonas played the dominant role in consortium GYB1. And embedding obviously altered the community structure and the key bacterial genera during the PCB removal process. Therefore, the immobilization of bacteria consortium by sodium alginate-biochar enhanced the biodegradation of PCB 118, which will provide new insights into functional microorganisms' actual application for PCB restoration.

Fungal pellets immobilized bacterial bioreactor for efficient nitrate removal at low C/N wastewater

In this study, fungal pellets immobilized denitrifying Pseudomonas stutzeri sp. GF3 was cultivated to establish a bioreactor. The denitrification effect of fixed bacteria with fungal pellets was tested by response surface methodology (RSM). Analysis of the bioreactor showed that the denitrification efficiency reached 100% under the optimal conditions and the denitrification efficiency of the actual wastewater treatment in the stable phase reached 95.91%. Moreover, the organic matter and functional groups in the bioreactor under different C/N conditions were analyzed by fluorescence excitation-emission matrix (EEM) spectra and Fourier transform infrared spectroscopy (FTIR), which revealed that metabolic activities of denitrifying bacteria were enhanced with the increase of C/N. The morphology and structure of bacteria immobilized by fungal pellets explored by scanning electron microscope (SEM) showed the filamentous porous fungal pellets loaded with bacteria. Community structure analysis by high-throughput sequencing demonstrated that strain GF3 might was the dominant strain in bioreactor.

Impact of C/N ratio on the fate of simultaneous Ca2+ precipitation, F- removal, and denitrification in quartz sand biofilm reactor

The coexistence of F^-, Ca²⁺, nitrates, and other pollutants in water body has aroused widespread concern. In this research, a novel quartz sand biofilm reactor was established, aiming to study the key factors of different carbon to nitrogen (C/N) ratios (5:1, 4:1, and 3:1), initial Ca²⁺ concentration (180 mg L^-1, 144 mg L^-1, and 108 mg L^-1), and hydraulic retention time (HRT) (4 h, 6 h, and 8 h) on simultaneous Ca²⁺ precipitation, F^- removal, and denitrification. Results showed that the removal efficiencies of Ca²⁺, F^-, and nitrate were 55.04%, 82.64%, and 97.69% under the low C/N ratio of 3:1, initial Ca²⁺ concentration of 180 mg L^-1, and HRT of 8 h. 3-D Excitation-Emission Fluorescence Spectroscopy (3-D EEM) demonstrates that extracellular polymeric substances (EPS) was generated during the growth metabolism. Scanning Electron Microscopy (SEM) and X-ray diffractometer images showed that Ca²⁺, F^- removed in the form of CaCO₃, Ca₅(PO₄)₃F and CaF₂ under Acinetobacter sp. H12 induction. Moreover, high-throughput sequencing results display that the biomineralized bacteria Acinetobacter sp. H12 exerted great influence in the bioreactor. This research will underpin the practical use of multiple pollutants such as F^- and Ca²⁺ wastewater under the different C/N ratios.

From the Andes to the desert: 16S rRNA metabarcoding characterization of aquatic bacterial communities in the Rimac river, the main source of water for Lima, Peru

The Rimac river is the main source of water for Lima, Peru's capital megacity. The river is constantly affected by different types of contamination including mine tailings in the Andes and urban sewage in the metropolitan area. In this work, we aim to produce the first characterization of aquatic bacterial communities in the Rimac river using a 16S rRNA metabarcoding approach which would be useful to identify bacterial diversity and potential understudied pathogens. We report a lower diversity in bacterial communities from the Lower Rimac (Metropolitan zone) in comparison to other sub-basins. Samples were generally grouped according to their geographical location. Bacterial classes Alphaproteobacteria, Bacteroidia, Campylobacteria, Fusobacteriia, and Gammaproteobacteria were the most frequent along the river. Arcobacter cryaerophilus (Campylobacteria) was the most frequent species in the Lower Rimac while Flavobacterium succinicans (Bacteroidia) and Hypnocyclicus (Fusobacteriia) were the most predominant in the Upper Rimac. Predicted metabolic functions in the microbiota include bacterial motility and quorum sensing. Additional metabolomic analyses showed the presence of some insecticides and herbicides in the Parac-Upper Rimac and Santa Eulalia-Parac sub-basins. The dominance in the Metropolitan area of Arcobacter cryaerophilus, an emergent pathogen associated with fecal contamination and antibiotic multiresistance, that is not usually reported in traditional microbiological quality assessments, highlights the necessity to apply next-generation sequencing tools to improve pathogen surveillance. We believe that our study will encourage the integration of omics sciences in Peru and its application on current environmental and public health issues.

Characteristics of bacterial community structure and function associated with nutrients and heavy metals in coastal aquaculture area

Coastal aquaculture area has become one of the critical zones that are more susceptible to the influence of human activity. Many aquaculture operations invariably result in the accumulation of nutrients and heavy metals in the coastal ecosystem. Our study investigated sediment bacterial community structure and function across 23 sites under the influence of nutrients and heavy metals in the coastal aquaculture area. The habitat environment of the sediment was described by analyzing physicochemical characteristics. Sediment bacterial community structure and diversity were investigated by 16S rRNA sequencing. The sequencing data presented that Proteobacteria, Bacteroidetes, Planctomycetes, Acidobacteria and Chloroflexi were predominant at phylum level. Variations in the bacterial community composition and diversity were significant (P < 0.01) among different groups (according to the distance from the bank side) which indicated that specific environmental conditions had shaped distinct bacterial community. Specifically, bacterial diversity and composition were significantly influenced by the temperature, salinity, pH, dissolved oxygen (DO), TOC, TON, nitrite, nitrate and heavy metals (P < 0.05). Results related to functional prediction demonstrated that carbon, nitrogen and sulfur metabolism were the dominant processes in the coastal aquaculture area. In the meantime, the potential pathogens such as Arcobacter was found in site S3, which indicated the possible threat to the cultured species in this area. Overall, variations in bacterial communities caused by nutrients and heavy metals can affect biogeochemical cycles, which may provide an indication for the protection of coastal aquaculture environments.

Denitrification performance and bacterial flora analysis of immobilized denitrification filler in industrial wastewater

The study aimed at evaluating the nitrogen removal performance of the immobilized denitrification filler, and the influence of shock loading on the high-rate denitrification process. A pilot scale reactor was operated for treatment of aniline production wastewater. The nitrogen removal activity significantly increased in the continuous feed experiments, reaching 5.23 kg N m^-3 day^-1 on day 31 (30 °C) at Hydraulic Retention Time (HRT) = 10 h. In the impact experiment, the denitrification filler was inhibited by Free Nitrite Acid (FNA) when the shock load flowed 1.5 times into the bioreactor and recovered after the load was restored for 20 h. The high-throughput results demonstrated that the dominant position of the denitrifying bacteria further enhanced in a micro toxic and high-salinity environment, providing a basis for the dominance of the composite denitrifying bacteria and the efficacy of the immobilization technology.

Nitrogen removal performance and bacterial communities in zeolite trickling filter under different influent C/N ratios

In this study, the degradation performance of nutrients in zeolite trickling filter (ZTF) with different influent C/N ratios and aeration conditions was investigated. Microaeration was beneficial for enhancing NH₄⁺-N removal performance. Due to the sufficient carbon source supply under a C/N ratio of 8, a high removal efficiency of NH₄⁺-N and TN was simultaneously observed in ZTF. In addition, TN removal mainly occurred at the bottom, which might be explained by the sufficient nutrients available for bacteria to multiply in this zone. The abundant genera were Acinetobacter, Gemmobacter, Flavobacterium, and Pseudomonas, all of which are heterotrophic nitrification-aerobic denitrification (HNAD) bacteria. In addition, biofilm only slowed down the adsorption rate but did not significantly reduce the adsorption capacity of zeolite. Bio-zeolite had NH₄⁺-N well adsorption capacity and bio-desorption capacity. Biological nitrogen removal performance was superior to physicochemical absorption of zeolite. The results suggested that the physicochemical of zeolite and biochemical reactions of microorganism coupling actions may be the main nitrogen transformation pathway in ZTF. Our research provides a reference for further understanding the nitrogen removal mechanism of zeolite bioreactors.

Performance and microbial community of a novel PVA/iron-carbon (Fe–C) immobilized bioreactor for nitrate removal from groundwater

An efficient immobilized denitrification bioreactor functioning under anaerobic conditions was developed by combining bacterial immobilization technology with iron-carbon (Fe–C) particles. The effects of key factors on nitrate (NO3 −–N) removal efficiency were invested, such as the carbon-nitrogen ratio (C/N), pH and hydraulic retention time (HRT). Experimental results show that 100.00% NO3 −–N removal efficiency and a low level of nitrite (NO2 −–N) accumulation less than 0.05 mg L−1 were obtained under the condition of a C/N ratio of 3, pH 7.0 and HRT of 6 h. Meteorological chromatographic analysis showed that the final product of denitrification was mainly nitrogen (N2). The main component of precipitation formed in the bioreactor was characterized as Fe3O4 by X-ray diffraction. High-throughput sequencing analysis indicated that the dominant bacterial class in the Fe–C bioreactor was Gammaproteobacteria, while the dominant genera were Zoogloea and Azospira, the relative abundances of which were as high as 23.25 and 15.43%, respectively.

Efficient nitrate removal by Pseudomonas mendocina GL6 immobilized on biochar

The performance of nitrate removal by Pseudomonas mendocina GL6 cells immobilized on bamboo biochar was investigated. The results showed that immobilized bacterial cells performed better nitrate removal than the free bacterial cells, and the nitrate removal rate increased from 6.51 mg/(L·h) of free cells to 8.34 mg/(L·h) of immobilized cells. The nitrate removal of immobilized bacterial cells fitted well to the zero-order kinetics model. Moreover, bath experiments showed that immobilized bacterial cells displayed more nitrate removal capacity under different conditions than free bacterial cells due to the protection of biochar carrier. The subsequent mechanistic study suggested that biochar promoted the expression level of denitrification functional genes (napA and nirK) and electron transfer genes involved in denitrification (napB and napC), which resulted in the increase of nitrate removal efficiency. Thus, biochar-immobilized P. mendocina GL6 has much potential to remove nitrate from wastewater via aerobic denitrification.

Polyethylenimine-functionalized polyacrylonitrile anion exchange fiber as a novel adsorbent for rapid removal of nitrate from wastewater

The development of an adsorbent with high adsorption ability and favorable cyclic regeneration performance for the removal of nitrate residues from wastewater is a task of vital importance. To this end, polyacrylonitrile fiber (PANF) was modified with polyethyleneimine (PEI), and alkyl groups were then introduced around the active amine groups to prepare three polymer-based anion exchange fibers (PAN-PEI-3C, PAN-PEI-5C, and PAN-PEI-8C). The novel fibers were characterized using techniques such as scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). The adsorption isotherms of the fibers were best fitted by the Langmuir model, and PAN-PEI-5C exhibited a higher adsorption amount of nitrate (31.32 mg/g) than the other adsorbents. The equilibrium was reached expeditiously (within 10 min), and both pseudo-first-order and pseudo-second-order models could well describe the adsorption kinetics. More attractively, the saturated PAN-PEI-5C could be eluted using a low-concentration (0.3 M) NaCl solution, without any sharp loss of adsorption amount for five consecutive cycles in the presence of dissolved organic matter (DOM). Furthermore, PAN-PEI-5C could effectively adsorb low-concentration nitrate from real secondary effluents in a fixed-bed column experiment. Our work provides a promising and low-cost material for the removal of nitrate residues in practical applications.

Denitrification performance evaluation and kinetics analysis with mariculture solid wastes (MSW) derived carbon source in marine recirculating aquaculture systems (RAS)

Biological denitrification using mariculture solid wastes (MSW) carbon source is a promising solution for removing nitrate (NO₃^--N) and disposing MSW in marine recirculating aquaculture systems (RAS). To enhance denitrification performance, heating (HT), rhamnolipid (RL), alkali (AL), thermophilic bacteria (TB) pre-treated MSW acidogenic fermentation effluents were prepared as carbon sources. Profiles of soluble organics in four types of fermentation effluents were first evaluated. The highest volatile fatty acids (VFAs) yield (52.1%) was obtained from TB treated MSW after acidification. RL and TB treated MSW acidogenic fermentation effluents showed high NO₃^--N removal efficiency (NRE) (around 97%). Acidogenic fermentation effluent from TB treated MSW presented a high biodegradability, with the minimum effluent chemical oxygen demand (COD) amount (35 mg/L). Denitrification kinetics parameters were also analyzed; high fraction (74.5%) of the most readily biodegradable organics (S_S) demonstrated that TB treated MSW acidogenic fermentation effluent is a high-quality carbon source for enhancing denitrification.

Using cold-adapted river-bottom sediment as seed sludge for sulfur-based autotrophic denitrification operated at mesophilic and psychrophilic temperatures

Aiming for total nitrogen (TN) pollution control in the urbanized stream, this study proposed and verified a strategy of cultivating and acclimating sulfur-based autotrophic denitrifiers by using river-bottom sediments as seed sludge, and investigated temperature effects on sulfur-based autotrophic denitrification (SAD). With thiosulfate as an electron donor, seven SAD batch reactors were operated and studied at both 15 °C and 30 °C, to compare reactor performance and their microbial community analysis results. In the first batch, three parallel reactors (A1, A2, and A3) were operated at 30 °C for 30 days. The dynamic analysis showed that sequentially decreasing temperature to 20, 15, and 10 °C had significant adverse effects on nitrate-loading rates. In the second batch, two groups of parallel reactors were operated at 30 °C (B1 and B2) and 15 °C (C1 and C2) for 45 days. High TN removal efficiencies (>95%) were achieved in all four reactors, with comparable nitrate loading rates and less nitrite accumulation at 15 °C. High-throughput sequencing revealed that genus Thiobacillus was predominant (66.3-90.0%) in all seven reactors. However, at the operational taxonomic unit level, microbial communities at 15 °C and 30 °C were significantly different, indicating that dissimilar strains were cultivated. Our findings suggested that deliberately cultivating cold-adapted denitrifiers helps SAD to achieve high TN removal at psychrophilic temperatures and thus, is important for future applications in practical TN pollution control in urbanized streams.

The mechanism of nitrate-Cr(VI) reduction mediated by microbial under different initial pHs

To date, comparatively little research is known about the role of pH conditions in bioremediation of Cr(VI) contaminated aquifers. This study explored microbial Cr(VI) reduction and denitrification under different initial pHs. The underlying mechanism was also investigated. When testing 50 mg/L-N nitrate and 10 mg/L Cr(VI), complete contaminants removal was observed at initial pH 10.0 and 11.0, and only 10 %-30 % of removal achieved under other conditions, which might be ascribe to the significant up-regulation of functional genes narG (8.31 and 10.46 folds) and azoR (24.90 and 15.96 folds) at initial pH 10.0 and 11.0. Metagenomic sequencing showed that alkali tolerant bacteria played major roles in the NO₃^--Cr(VI) reduction (i.e. Pannonibacter increased by 13.08 % and 25.24 % at initial pH 10.0 and 11.0), and metabolic pathways of Degradation and Energy were found of increased abundant. Furthermore, a significative study suggested that potential interspecies cooperation existed at initial pH 11.0 to facilitating the simultaneous removal of contaminants, and Pannonibacter indicus might be an important participant in the degradation of contaminants. The results of this study will fully understand the metabolic patterns of bacteria under alkaline conditions, expand the range of available functional bacteria, and enhance the practical aspects of co-contaminants remediation.

Simultaneous nitrate, nickel ions and phosphorus removal in a bioreactor containing a novel composite material

This study presents the novel composite material TMCC/PAA/SA@Fe(TPSA), a bacteria immobilized carrier for use in bioreactor systems to enhance the simultaneous removal efficiency of nitrate, Ni(II) and phosphorus. The influence of various operational factors were evaluated on the performance of nitrate, phosphorus and Ni(II) removal. Results demonstrate that under optimum conditions of an hydraulic retention time (HRT) of 8 h and pH 7.0, nitrate and phosphorus removal reached nearly 100% and 61.7%, respectively. When the initial Ni(II) concentration was 1 mg/L, approximately 100% Ni(II) removal efficiency was achieved. Furthermore, the morphology and components of the TPSA immobilized bacterial pellets were analyzed to investigate the mechanism of simultaneous nitrate, Ni(II) and phosphorus removal. Microbial metabolism was more active in the experimental reactor compared with control, although high concentrations of Ni(II) could inhibit bacterial activity.

Heterotrophic denitrification strategy for marine recirculating aquaculture wastewater treatment using mariculture solid wastes fermentation liquid as carbon source: Optimization of COD/NO3--N ratio and hydraulic retention time

Heterotrophic denitrification using mariculture solid wastes (MSW) fermentation liquid as carbon source is an economically and environmentally sustainable strategy for NO₃^--N removal in marine recycling aquaculture systems (RAS). The optimization of COD/NO₃^--N ratio (C/N) and hydraulic retention times (HRT) with respect to MSW fermentation liquid driven denitrification for marine RAS wastewater treatment was investigated. The optimum C/N of 8 and HRT of 6 h for heterotrophic denitrification was obtained with NO₃^--N removal efficiency of 97.8% and 94.2%, respectively. Using MSW fermentation liquid as carbon source, the utilization of VFAs was more effective than that of carbohydrates and proteins, and effluent COD concentration decreased with an increment in HRT from 4 to 8 h. The results of high-throughput sequencing analysis showed microbial communities were enriched selectively in the reactors by optimizing C/N and HRT, which obviously enhanced the nitrogen removal in respect to MSW fermentation liquid driven denitrification.

Intensified nitrogen removal by heterotrophic nitrification aerobic denitrification bacteria in two pilot-scale tidal flow constructed wetlands: Influence of influent C/N ratios and tidal strategies

This study investigated the influence of C/N ratios and tidal strategies on nitrogen removal and bacterial communities in two pilot-scale tidal flow constructed wetlands (TFCWs) with simultaneous nitrification-denitrification process. Heterotrophic nitrification aerobic denitrification (HNAD) was the main nitrogen transformation pathway in both TFCWs. High C/N ratios and effluent circulation at low temperature promoted HNAD in TFCWs with high nitrogen removal efficiencies (72.6%-95.5% for NH₄⁺-N and 70.9%~91.8% for TN). Effluent circulation had more influence on bacterial community structure and diversity than C/N ratios. Among 16 detected genera related to nitrogen removal, HNAD bacteria (HNADB) were abundant. Especially, some dominant HNADB (e.g. Aeromonas, Hydrogenophage and Gemmobacter) were core genera, showing positive interactions with other genera related to nitrogen removal. Tidal strategies had more contribution to the shifts in these genera than C/N ratios. This study highlights the importance of HNADB in pilot-scale TFCWs and their responses to C/N ratios and tidal strategies.

pH control and microbial community analysis with HCl or CO2 addition in H2-based autotrophic denitrification

H₂-based autotrophic denitrification is promising to remove nitrate from water or wastewater lacking organic carbon sources, and pH is one of its most important process parameters. HCl and CO₂ addition are known as adequate pH control methods for practical purposes. However, because of H₂, added CO₂ may participate in microbial metabolisms and affect denitrification mechanisms. Here, a combined micro-electrolysis and autotrophic denitrification (CEAD) reactor, in which H₂ is generated based on galvanic-cell reactions between zero-valent iron and carbon, was optimized and continuously operated for 233 days by adding HCl or CO₂ to control pH in the range of 7.2-8.2. Microbial communities were compared between the two pH-control methods through high-throughput sequencing of 16S rRNA, nirS, and nirK genes. Under a low COD/N ratio of 0.5 in the influent (with ∼36 mgNO₃^--N/L), when adding HCl, the total nitrogen (TN) removal efficiency reached 91.4% ± 0.9% with a 28-h hydraulic retention time (HRT). When adding CO₂, the TN removal efficiency was improved to 96.5% ± 1.7% with 24-h HRT. Significant differences of 16S rRNA and nirS genes between the two pH-control stages indicated the variation of microbial communities and nirS-type denitrifiers. With HCl addition, Thiobacillus, unclassified Comamonadaceae, Arenimonas, Limnobacter, and Thermomonas, which were reported previously as likely autotrophic or heterotrophic denitrifiers, were most dominant in the biofilms. With CO₂ addition, the biofilms became dominated by Anaerolineaceae and Methylocystaceae (related to organic carbon metabolism), Denitratisoma (likely heterotrophic denitrifier), and uncultured bacteria TK10 and AKYG587. The results suggest that the added CO₂ not only contributed to pH control but also participated in microbial metabolisms. This study provides useful insights into microbial mechanisms and further optimization of H₂-based autotrophic denitrification in water and wastewater treatment.

Application of a new type of Si–Al porous clay material as a solid phase support for immobilizing Acidovorax sp. PM3 to treat domestic sewage

A novel Si–Al porous clay material W (reprocessed from ceramic waste) was used for Acidovorax sp. strain PM3 immobilization to promote the growth of strains and improve nitrogen and phosphorus removal performance in water treatment systems. The porous clay material W was characterized by X-ray diffraction, Fourier-transform infrared spectroscopy, and scanning electron microscopy indicating that porous clay material W was a type of mullite with 63.52 m2/g specific surface area. After immobilization, the maximum biomass increased 2.7 times the specific growth rate and the removal rates of chemical oxygen demand (COD), ammonia (NH4+–N), and total phosphorus (TP) by the immobilized PM3 were 42.99, 29.19, and 11.76% higher than the free strain after 24 h. The Monod equation showed that the growth rate and processing speed of immobilized PM3 increased. The maximum adsorption capacities of COD and NH4+–N onto porous clay material W were 2.33 and 0.32 mg/g on the basis of Langmuir isotherm. The removal capacities of COD, NH4+–N, and TP by the immobilized PM3 were 588.24, 20.37, and 5.06 mg/l, respectively, as shown by kinetic studies. These results demonstrated that porous clay material W could improve the efficiency of microbial nitrogen and phosphorus removal, and the immobilized microorganism system could effectively treat domestic sewage. The adsorption isotherms can well describe the adsorption process. The maximum adsorption capacity of COD and NH4+–N on porous clay material W is 2.33 and 0.32 mg/g, respectively. Kinetic studies showed that the removal capacity of immobilized PM3 to COD, NH4+–N, and TP was 58.824, 20.37, and 5.06 mg/l, respectively.

Simultaneous removal of sulphur dioxide and nitric oxide at different oxygen concentrations in a thermophilic biotrickling filter (BTF): Evaluation of removal efficiency, intermediates interaction and characterisation of microbial communities

Simultaneous flue gas desulphurisation and denitrification in biotrickling filter was investigated under different O₂ concentrations (0%, 3%, 5%, 8% and 10%) at 45 °C. NO and SO₂ removal efficiency, intermediates (NO₃^-, NO₂^-, NO₂, SO₄^2- and S^2-) interaction and accumulation, S⁰ recovery and microbial community structure were investigated. Results indicated the highest NO removal efficiency was 96.5% at 5% O₂. Maximum SO₂ removal efficiency was 95.6% at 3% O₂. Moreover, N intermediates accumulation increased when O₂ concentration increased from 0% to 10%. The lowest S^2- concentration of 61 mg/L and the maximum S⁰ recovery of 76.9% were achieved at 5% O₂. The bioreactor at 10% O₂ contained less bacterial OTUs richness and evenness compared with other conditions. Illumina analysis indicated Proteobacteria, Firmicutes and Bacteroidetes were the dominant members. Overall, microbial community structure differs significantly under different O₂ concentrations.