Application of cellulose nanocrystals prepared from agricultural wastes for synthesis of starch-based hydrogel nanocomposites: Efficient and selective nanoadsorbent for removal of cationic dyes from water

A sustainable approach to dye degradation: Horseradish peroxidase immobilization on hybrid chitosan-coated magnesium manganese oxide materials

This study explores the potential of chitosan-coated magnesium manganese oxide (CS-MgMn2O4) as a robust support material for horseradish peroxidase (HRP) immobilization, aiming to increase its catalytic efficiency and reusability. The CS-MgMn2O4 matrix, synthesized via a green chemistry approach, was characterized for its structural and surface properties using techniques such as FTIR, SEM, BET, and XRD. Compared with free HRP, immobilized enzyme presented improved kinetic parameters, thermal stability, and solvent tolerance. The optimal conditions for enzymatic activity were identified, including a pH of 6.0 and a catalyst dosage of 30 mg, achieving a maximum methyl orange (MO) degradation efficiency of 78 % within 5 h. The degradation efficiency peaked at 91 % under optimal substrate concentration (20 mg/L MO), with a decrease at higher concentrations. Additionally, the immobilized HRP demonstrated excellent reusability, retaining 59 % of its activity after five cycles. These results underscore the advantages of CS-MgMn2O4 as a hybrid material that combines high porosity, biocompatibility, and structural stability, to overcome the limitations associated with free enzymes. This study provides a sustainable and efficient strategy for dye degradation in wastewater treatment, highlighting the potential of enzyme immobilization on advanced hybrid materials for environmental applications.

Mechanistic and adsorption kinetics study of sulfonated activated carbon enhanced starch-based aerogel for high efficient adsorption of cationic and anionic dyes

Starch-based aerogels, with their low density, high porosity, and high specific surface area, show potential for application in dye adsorption. However, most of the current starch-based aerogels exhibited limitations, such as limited adsorption capacity and poor ability to selective treatment in complex dye wastewater. In this study, acrylic acid (AA) and allyl sulfonic acid sodium salt (AS) were grafted onto the carboxymethyl starch sodium (CMS) backbone via UV-induced radical polymerization, and combined with sulfonated activated carbon (SAC) to prepare a CAA/SAC starch-based aerogel with low density (0.29 g/cm3), high porosity (86.48 %), and notable swelling capacity (60.78 g/g). Activated carbon with porous structures was sulfonated with concentrated sulfuric acid to introduce -SO3H groups. These groups, along with the negative charges on CMS, AA, and AS, enable selective adsorption of cationic dyes. The adsorption capacity of CAA/SAC aerogel for the cationic dye methylene blue was 136.43 mg/g, which was significantly higher than that of the anionic dye methyl orange (69.31 mg/g). The adsorption process followed both pseudo-second-order kinetics and Langmuir isotherm. The CAA/SAC aerogel can effectively remove dye molecules from wastewater, showing promising potential for various wastewater treatment applications.

Nanocellulose-hydrogel hybrids: A review on synthesis and applications in agriculture, food packaging and water remediation

The growing demand for sustainable and environment-friendly materials has driven extensive research on biopolymers for applications in agriculture, food science, and environmental remediation. Among these, nanocellulose-hydrogel hybrids (NC-HHs) have gained significant attention as an innovative class of bio-based materials that uniquely combine the remarkable physicochemical properties of nanocellulose with the functional versatility of hydrogels. These hybrids are characterised by exceptional water retention, mechanical strength and biodegradability, enabling advances in precision agriculture, smart food preservation and contaminant remediation. This review provides a comprehensive understanding of the synthesis, properties, and multifunctional applications of NC-HHs, emphasising their innovative role in sustainability. In agriculture, NC-HHs enhance soil moisture retention, support plant growth, and serve as carriers for controlled-release fertilizers, optimizing water and nutrient use efficiency. In the food industry, they enable intelligent packaging solutions that extend shelf life, monitor food freshness, and inhibit microbial growth. Additionally, NC-HHs present groundbreaking strategies for environmental remediation by effectively immobilizing pollutants in water and soil. Beyond summarizing recent advances, this review presents an in-depth mechanistic perspective on the interactions between NC and HH, critically evaluating their structure-property relationships, functional adaptability and application-specific performance. By integrating recent advances in nanocellulose functionalisation, polymer chemistry and the development of responsive hydrogels, this review critically examines the key technological innovations and future prospects of NC-HHs, underscoring their transformative potential in addressing global challenges related to food security, environmental sustainability, and sustainable agricultural practices.

Enzymatic bioremediation of polycyclic aromatic hydrocarbons (PAHs) in contaminated soil: a study on the recombinant laccase TVL

Polycyclic aromatic hydrocarbons (PAHs) are pervasive and persistent pollutants in contaminated soil, posing a severe health and environmental threat. Enzymatic bioremediation presents a viable solution for the remediation of PAH-contaminated soil. In this study, a recombinant laccase with the encoding gene originating from Trametes villosa and recombinantly expressed in Aspergillus oryzae, designated as TVL, was discovered to possess strong PAH reduction capabilities. The specific enzyme activity of TVL was 73485 and 5102 LAMU/g enzyme protein at pH 5.0/7.0 and 37°C. Furthermore, it exhibited significant benzo[a]pyrene degradation, with 100% and 90.48% degradation at pH 5.0/7.0 after 24 h in the liquid phase. The degradation process of benzo[a]pyrene in soil was thoroughly investigated. Optimal conditions were identified as 15 mg/g NK-BSoil-3 and 1.35 mg/g HBT, resulting in a removal rate of 37.54% within 7 days when 0.01 U/g of TVL was applied. The potential mechanisms were investigated using molecular docking simulation. The binding energy between benzo[a]pyrene and TVL protein is notably robust, suggesting a higher propensity for enzyme binding. The TVL protein pocket contains nine amino acids that can interact most strongly with benzo[a]pyrene. Consequently, the recombinant laccase TVL holds considerable practical significance in bioremediation.

Carbon dots-loaded cellulose nanofibrils hydrogel incorporating Bi2O3/BiOCOOH for effective adsorption and photocatalytic degradation of lignin

A novel photocatalytic adsorbent, a cellulose nanofibrils based hydrogel incorporating carbon dots and Bi2O3/BiOCOOH (designated as CCHBi), was developed to address lignin pollution. CCHBi exhibited an adsorption capacity of 435.0 mg/g, 8.9 times greater than that of commercial activated carbon. This enhanced adsorption performance was attributed to the 3D porous structure constructed using cellulose nanofibrils (CNs), which increased the specific surface area and provided additional sorption sites. Adsorption and photocatalytic experiments showed that CCHBi had a photocatalytic degradation rate constant of 0.0140 min-1, 3.1 times higher than that of Bi2O3/BiOCOOH. The superior photocatalytic performance of CCHBi was due to the Z-scheme photocatalytic system constructed by carbon dots-loaded cellulose nanofibrils and Bi2O3/BiOCOOH, which facilitated the separation of photoinduced charge carriers. Additionally, the stability of CCHBi was confirmed through consecutive cycles of adsorption and photocatalysis, maintaining a removal efficiency of 85 % after ten cycles. The enhanced stability was due to the 3D porous structure constructed by CNs, which safeguarded the Bi2O3/BiOCOOH. This study validates the potential of CCHBi for high-performance lignin removal and promotes the application of CNs in developing new photocatalytic adsorbents.

Development of Slow-Release Fertilizers with Function of Water Retention Using Eco-Friendly Starch Hydrogels

Over the past two decades, the development and commercialization of slow-release fertilizers (SRFs) have significantly advanced, with the primary aim of mitigating environmental issues associated with excessive fertilizer use. A range of methodologies, including chemical and physical reactions, incorporation into carriers with porous and layered structures, and coating techniques, have been explored and refined. On the other hand, global challenges such as drought and desertification further underscore the need for SRFs that not only control nutrient release but also improve soil moisture retention. This paper reviews the development and application of eco-friendly starch hydrogels as fertilizer carriers and water retention for SRFs, particularly starch-based superabsorbent polymers (SAPs) produced through grafting copolymerization with acrylamide. This review explores both scientific issues, such as the microstructures and releasing mechanisms of SAPs, and technical development, involving copolymerization technologies, multi-initialization processes, methods of loading fertilizer into hydrogel, etc. Starch, as both a biodegradable and renewable carbohydrate polymer, offers distinct advantages due to its excellent chemical stability and high reactivity. The fabrication techniques of SAPs have been developed from traditional batch polymerization in aqueous solutions to more efficient, solvent-free reactive extrusion. The benefits of SRFs based on SAPs encompass enhanced soil aeration, the prevention of soil deterioration, the minimization of water evaporation, environmental pollution control, reduction in plant mortality, and prolonged nutrient retention within soil. In this review, we summarize the current progress, identify limitations in existing technologies, and propose future research directions to further enhance the performance of starch-based SRFs.

Gels for Water Remediation: Current Research and Perspectives

The development of cost-effective and high-performance technologies for wastewater treatment is essential for achieving a sustainable economy. Among the various methods available for water remediation, adsorption is widely recognized as an effective and straightforward approach for removing a range of pollutants. Gel materials, particularly hydrogels and aerogels, have attracted significant research interest due to their unique properties. Hydrogels, for instance, are noted for their ability to be regenerated and reused, ease of separation and handling, and suitability for large-scale applications. Additionally, their low cost, high water absorption capacity, and contribution to environmental protection are important advantages. Aerogels, on the other hand, are distinguished by their low thermal conductivity, transparency, flexibility, high porosity, mechanical strength, light weight, large surface area, and ultralow dielectric constant. This review provides a comprehensive analysis of the current literature, highlighting gaps in knowledge regarding the classification, preparation, characterization, and key properties of these materials. The potential application of hydrogels and aerogels in water remediation, particularly in removing contaminants such as dyes, heavy metals, and various organic and inorganic pollutants, is also discussed.

Starch-based hydrogels for environmental applications: A review

Water sources have become extremely scarce and contaminated by organic and inorganic industrial and agricultural pollutants as well as household wastes. Poisoning water resources by dyes and metals is a problem because contaminated water can leak into subsurface and surface sources, causing serious contamination and health problems. Therefore, developing wastewater treatment technologies is valuable. Today, hydrogels have attracted considerable attention owing to their broad applications. Hydrogels are polymeric network compositions with significant water-imbibing capacity. Hydrogels have potential applications in diverse fields such as biomedical, personal care products, pharmaceuticals, cosmetics, and biosensors. They can be prepared by using natural (biopolymers) and synthetic polymers. Synthetic polymer-based hydrogels obtained from petrochemicals are not environmentally benign; thus, abundant plant-based polysaccharides are found as more suitable compounds for making biodegradable hydrogels. Polysaccharides with many advantages such as non-toxicity, biodegradability, availability, inexpensiveness, etc. are widely employed for the preparation of environmentally friendly hydrogels. Polysaccharides-based hydrogels containing chitin, chitosan, gum, starch (St), etc. are employed to remove pollutants, metals, and dyes. Among these, St has attracted a lot of attention. St can be mixed with other compounds to make hydrogels, which remove dyes and metal ions to variable degrees of efficiency. Although St has numerous advantages, it suffers from drawbacks such as low stability, low water solubility, and fast degradability in water which limit its application as an environmental adsorbent. As an effective way to overcome these weaknesses, various modification approaches to form starch-based hydrogels (SBHs) employing different compounds have been reported. The preparation methods and applications of SBH adsorbents in organic dyes, hazardous materials, and toxic ions elimination from water resources have been comprehensively discussed in this review.

Enhanced dye sequestration with natural polysaccharides-based hydrogels: A review

Due to the expansion of industrial activities, the concentration of dyes in water has been increasing. The dire need to remove these pollutants from water has been heavily discussed. This study focuses on the reproducible and sustainable solution for wastewater treatment and dye annihilation challenges. Adsorption has been rated the most practical way of the several decolorization procedures due to its minimal initial investment, convenient utility, and high-performance caliber. Hydrogels, which are three-dimensional polymer networks, are notable because of their potential to regenerate, biodegrade, absorb bulky amounts of water, respond to stimuli, and have unique morphologies. Natural polysaccharide hydrogels are chosen over synthetic ones because they are robust, bioresorbable, non-toxic, and cheaply accessible. This study has covered six biopolymers, including chitosan, cellulose, pectin, sodium alginate, guar gum, and starch, consisting of their chemical architecture, origins, characteristics, and uses. The next part describes these polysaccharide-based hydrogels, including their manufacturing techniques, chemical alterations, and adsorption effectiveness. It is deeply evaluated how size and shape affect the adsorption rate, which has not been addressed in any prior research. To assist the readers in identifying areas for further research in this subject, limitations of these hydrogels and future views are provided in the conclusion.

Surface engineering of multifunctional nanostructured adsorbents for enhanced wastewater treatment: A review

Rapid urbanization and industrialization have significantly contributed to the contamination of the environment through the discharge of wastewater containing various pollutants. The development of high-performance surface functional nanostructured adsorbents is of wide interest for researchers. Therefore, we explore the significant advancements in this field, focusing on the efficiency of nanostructured materials, as well as their nanocomposites, for wastewater treatment applications. The crucial role of surface modification in enhancing the affinity of these nanostructured adsorbents towards targeted pollutants, addressing a key bottleneck in the utilization of nanomaterials for wastewater treatment, was specifically emphasized. In addition to highlighting the advantages of surface engineering in enhancing the efficiency of nanostructured adsorbents, this review also provides a comprehensive overview of the limitations and challenges associated with surface-modified nanostructured adsorbents, including high cost, low stability, poor scalability, and potential nanotoxicity. Addressing these limitations is essential for realizing the commercial viability of these state-of-the-art materials for large-scale wastewater treatment applications. This review also thoroughly discusses the potential scalability and environmental safety aspects of surface-modified nanostructured adsorbents, offering insights into their future prospects for wastewater treatment. It is believed that this review will contribute significantly to the existing body of knowledge in the field and provide valuable information for researchers and practitioners working in the area of environmental remediation and nanomaterials.

A state-of-the-art review on plant-derived cellulose-based green hydrogels and their multifunctional role in advanced biomedical applications

The most prevalent carbohydrate on Earth is cellulose, a polysaccharide composed of glucose units that may be found in diverse sources, such as cell walls of wood and plants and some bacterial and algal species. The inherent availability of this versatile material provides a natural pathway for exploring and identifying novel uses. This study comprehensively analyzes cellulose and its derivatives, exploring their structural and biochemical features and assessing their wide-ranging applications in tissue fabrication, surgical dressings, and pharmaceutical delivery systems. The use of diverse cellulose particles as fundamental components gives rise to materials with distinct microstructures and characteristics, fulfilling the requirements of various biological applications. Although cellulose boasts substantial potential across various sectors, its exploration has predominantly unfolded within industrial realms, leaving the biomedical domain somewhat overlooked in its initial stages. This investigation, therefore, endeavors to shed light on the contemporary strides made in synthesizing cellulose and its derivatives. These innovative techniques give rise to distinctive attributes, presenting a treasure trove of advantages for their compelling integration into the intricate tapestry of biomedical applications.

Synthesis and characterization of copper nanoparticle-based hydrogel and its applications in catalytic reduction and adsorption of basic blue 3

Most of the dyes used in various industries are non-biodegradable and carcinogenic in nature. Therefore, elimination of dyes from textile wastes is mandatory to safeguard the life of human, aquatic animals and aquatic plants. In this connection an effective and eco-friendly hydrogel was synthesized from acrylamide, cellulose, clay, and copper salt abbreviated as AMPS(PHE-Ce)/MC-Cu. The fabricated hydrogel was used as sorbent and catalyst for the adsorption and catalytic reduction of basic blue 3. SEM analysis showed granular texture with small holes or cracks which is basic criteria for an adsorbent surface. The results showed that the BET surface area and the Langmuir surface area were, respectively, 27.87 and 40.32 m2/g. The FTIR analysis confirmed the synthesis of hydrogel, as is evident from peaks at 3500, 3439, 2996, 2414, and 1650 cm-1, which indicated the presence of OH or NH, -C-O-C-, CH3, (C[bond, double bond]O), C-N bonds correspondingly. Thermal stability was confirmed by TGA analysis where weight loss in three stages has been observed. The presence of copper was confirmed through EDX (5.02%) indicating the incorporation of cupper nanoparticles in hydrogel surface. The high adsorption capability of 1590 mg/g as recorded for basic blue-3 dye indicates it to be an efficient adsorbent. The swelling behavior characterized by Fickian diffusion up to 7898% clearly indicated significant swelling. Pseudo 2nd-order kinetics and the Langmuir isotherm models were more fit in unfolding kinetics and isothermal data indicating chemisorption with monolayer sorption as evident from the high R2 values (0.999) of each model. Thermodynamics considerations indicated that the adsorption process is endothermic with a positive enthalpy value of 1371.32 Jmol-1. The positive entropy value of 19.70 J/mol.K signifies a higher degree of disorder at the solid-liquid interface. The findings provided a valuable insights into the hydrogel's capacity to adsorb cationic dyes and reduce them catalytically, pointing towards its potential applications in addressing environmental challenges.

Porous superabsorbent composites prepared from aqueous foam template and application evaluation

Rapid water absorption is very important for the application of superabsorbent polymers under dry or semi-dry conditions, but there are currently few relevant studies. In this context, a novel porous superabsorbent of chitosan-grafted acrylic copolymer-2-acrylamido-2-methylpropanesulfonic acid/sapindus mukorossi pericarp/calcined oil shale semi-coke (CS-g-P(AA-co-AMPS)/SMP/COSSC) was prepared by a green and convenient foam template method, which was triggered by redox polymerization. The rich pore structure of the porous superabsorbent was conducive to accelerating the water absorption rate. It only took 15 min to reach a swelling capacity of 650 g g-1 in distilled water. Soil experiments show that even with the addition of 0.5 wt% porous superabsorbent, the soil water retention time can be extended to 7 days. Finally, it was applied to the growth of cabbage seeds and it was found that the growth was significantly improved. Based on these excellent properties, we expect to provide a valuable reference for the preparation of fast-absorbing materials through the green water-based foam template method, contributing to sustainable agriculture.

Cellulose nanocrystals extracted from rice husk using the formic/peroxyformic acid process: isolation and structural characterization

Cellulose derived from biomass is a renewable resource with numerous applications. Using formic/peroxyformic acid at atmospheric pressure, cellulose nanocrystals (CNC) were isolated from rice husk (RH) in this study. This method was an excellent way to get rid of lignin and hemicelluloses from RH. The cellulose was subsequently acid hydrolyzed by H2SO4 (64%) for 30 minutes at 45 °C. The chemical and microstructure analysis showed that the lignin and hemicellulose contents of raw RH had been eliminated, and the crystallinity content of CNC was 67.16%. According to transmission electron microscopy (TEM) morphological analysis, CNC measured 19 ± 3.3 nm in diameter, 195 ± 24 nm in length, and 10.2 ± 6.8 in aspect ratio. The thermal stability of RH and CNC was also investigated using thermogravimetric analysis (TGA). These encouraging findings demonstrated the potential for reusing RH agricultural waste to create CNC and include nanocomposites as a reinforcing material.

Compressible polydopamine modified pomelo peel powder/poly(ethyleneimine)/κ-carrageenan aerogel with pH-tunable charge for selective removal of anionic and cationic dyes

In this work, a novel biomass-based aerogel, polydopamine decorated pomelo peel powder/polyethyleneimine/κ-carrageenan (PPEKC) aerogel, was developed for dye wastewater treatment. The as-prepared PPEKC aerogel possessed a robust structure and good compressible resilience. As expected, this aerogel presented remarkable efficacy in eliminating both anionic and cationic dyes. The experimental maximum adsorption capacities were 2016.7 mg g-1 for congo red (CR) at pH = 5 and 1176.6 mg g-1 for methylene blue (MEB) at pH = 11, following with ultra-fast adsorption rates. The adsorption kinetics followed the pseudo-second-order model. The adsorption isotherms exhibited a stronger alignment with the Langmuir isotherm model for CR at 308 K and MEB at 288, 298, 308 K. The Freundlich isotherm model yielded a suitable fit for the adsorption of CR at 288 and 298 K. Thermodynamic analyses indicated that the removal of CR and MEB was spontaneous and endothermic. The adsorption mechanisms involved electrostatic interactions, π-π interactions, and hydrogen bonds. Intriguingly, it could achieve bidirectional selective adsorption of anionic and cationic dyes in the designed pH values, due to pH-tunable surface charge. Additionally, it also exhibited favorable reusability and antibacterial activity. Therefore, the as-prepared PPEKC aerogel could be a promising biosorbent for dye wastewater treatment.

Double-function ZnO/starch biodegradable hydrogel composite for methylene blue adsorption and photocatalytic degradation

An eco-friendly material for the removal of dyes from wastewater was developed. Biodegradable polymers (BP), cassava starch and poly(vinyl alcohol), were used to replace polyacrylamide. The hydrogel containing 50 wt% of BP (BP50) could absorb 34 times its dry weight of water. The hydrogel could adsorb Zn2+ and ZnO photocatalyst particles could be formed via a simple precipitation method. The incorporation of ZnO did not affect the adsorption efficiency of the ZnO/BP50 hydrogel composite towards methylene blue (MB). At initial concentrations (Co) below 4500 mg/g, the hydrogel composite removed ∼99 % of MB from solution in 3 h. The highest adsorption capacity of 1170 mg/g was obtained when Co was 6000 mg/g and at a dose of 0.10 g/20 mL. The hydrogel composite degraded 95 %-98 % of adsorbed MB at rates of 0.19 h-1 and 1.77 h-1 under UV irradiation and sunlight, respectively, with exposure times of 16 h for UV but only 2 h for sunlight. The material remained effective for at least 10 cycles of photodegradation under sunlight and removed 86 % of MB in solution on the 10th cycle. The composite also showed antibacterial activities and biodegradability in soil. These results indicated this material would not generate after-process toxic waste.

Trithiocyanurate-functionalized hydrochar for effectively removing methylene blue and Pb (II) cationic pollutants

Functionalization can change the physicochemical properties of hydrochar and improve its ability to adsorb pollutants. Herein, a trithiocyanurate-functionalized hydrochar (TTHC) was obtained from acylation of chloroacetyl chloride and hydrochar and modification with trithiocyanuric acid in alkaline conditions. TTHC can efficiently remove cationic methylene blue (MB) and Pb(II) from wastewater. The removal can be expressed with pseudo-second-order kinetic and Langmuir models. The MB and Pb(II) removed uptakes by TTHC at 298 K exceeded 909.9 and 182.8 mg g-1 respectively, and the removal rates reached 90% and 98% within 120 min respectively. Characterizations show TTHC is functionalized with trithiocyanurate, and rich in thiolate and aromaticity, and tends to adsorb MB/Pb(II) via multiple adsorption mechanisms. After five sorption-desorption regeneration cycles, TTHC maintained 80% and 99% adsorption capacities for MB and Pb(II) respectively. Therefore, TTHC is a promising efficient sorbent for removing MB and Pb(II) from effluents.

Polysaccharide-based nanoassemblies: From synthesis methodologies and industrial applications to future prospects

Polysaccharides, due to their remarkable features, have gained significant prominence in the sustainable production of nanoparticles (NPs). High market demand and minimal production cost, compared to the chemically synthesised NPs, demonstrate a drive towards polysaccharide-based nanoparticles (PSNPs) benign to environment. Various approaches are used for the synthesis of PSNPs including cross-linking, polyelectrolyte complexation, and self-assembly. PSNPs have the potential to replace a wide diversity of chemical-based agents within the food, health, medical and pharmacy sectors. Nevertheless, the considerable challenges associated with optimising the characteristics of PSNPs to meet specific targeting applications are of utmost importance. This review provides a detailed compilation of recent accomplishments in the synthesis of PSNPs, the fundamental principles and critical factors that govern their rational fabrication, as well as various characterisation techniques. Noteworthy, the multiple use of PSNPs in different disciplines such as biomedical, cosmetics agrochemicals, energy storage, water detoxification, and food-related realms, is accounted in detail. Insights into the toxicological impacts of the PSNPs and their possible risks to human health are addressed, and efforts made in terms of PSNPs development and optimising strategies that allow for enhanced delivery are highlighted. Finally, limitations, potential drawbacks, market diffusion, economic viability and future possibilities for PSNPs to achieve widespread commercial use are also discussed.

Cationic dialdehyde cellulose microfibers for efficient removal of eriochrome black T from aqueous solution

Materials based on cellulose have been widely used as a decontaminant agent of wastewater. However, it can not be found in the literature any application of the cationic dialdehyde cellulose (cDAC) in anionic dye removal. Therefore, this study aims a circular economy concept using sugarcane bagasse to obtain a functionalized cellulose by oxidation and cationization. cDAC was characterized by SEM, FT-IR, oxidation degree, and DSC. Adsorption capacity was evaluated by pH, kinetic, concentration effect, strength ionic tests, and recycling. The kinetic followed Elovich model (R² = 0.92605 for EBT = 100 mg/L) and non-linear Langmuir model (R² = 0.94542), which resulted in a maximum adsorption capacity of 563.30 mg/g. The cellulose adsorbent reached an efficient recyclability of 4 cycles. Thus, this work presents a potential material to become a new, clean, low-cost, recyclable, and environmentally friendly alternative for effluent decontamination-containing dyes.

A Comprehensive Review of Polysaccharide-Based Hydrogels as Promising Biomaterials

Polysaccharides have emerged as a promising material for hydrogel preparation due to their biocompatibility, biodegradability, and low cost. This review focuses on polysaccharide-based hydrogels' synthesis, characterization, and applications. The various synthetic methods used to prepare polysaccharide-based hydrogels are discussed. The characterization techniques are also highlighted to evaluate the physical and chemical properties of polysaccharide-based hydrogels. Finally, the applications of SAPs in various fields are discussed, along with their potential benefits and limitations. Due to environmental concerns, this review shows a growing interest in developing bio-sourced hydrogels made from natural materials such as polysaccharides. SAPs have many beneficial properties, including good mechanical and morphological properties, thermal stability, biocompatibility, biodegradability, non-toxicity, abundance, economic viability, and good swelling ability. However, some challenges remain to be overcome, such as limiting the formulation complexity of some SAPs and establishing a general protocol for calculating their water absorption and retention capacity. Furthermore, the development of SAPs requires a multidisciplinary approach and research should focus on improving their synthesis, modification, and characterization as well as exploring their potential applications. Biocompatibility, biodegradation, and the regulatory approval pathway of SAPs should be carefully evaluated to ensure their safety and efficacy.

Polypyrrole-Modified Nanocellulose Exhibits Superior Performance for Hg(II) Adsorption

Cellulose, a kind of polymer containing abundant functional groups, has widespread use in the adsorptive removal of environmental pollutants. An efficient and environmental friendly polypyrrole (PPy) coating approach is employed to modify the agricultural by-product straw derived cellulose nanocrystal (CNC) into excellent property adsorbents for removing the heavy metal ion of Hg(II). The FT-IR and SEM-EDS results demonstrated that PPy is formed on the surface of CNC. Consequently, the adsorption measurements proved that the obtained PPy-modified CNC (CNC@PPy) possesses a remarkably enhanced Hg(II) adsorption capacity of 1095 mg g^-1, owing to a plentiful functional group of doped Cl element on the surface of CNC@PPy by forming Hg₂Cl₂ precipitate. The results of the study suggest that the Freundlich model is more effective than the Langmuir model at describing the isotherms, while the pseudo-second order kinetic model is better suited to correlating with the experimental data compared to the pseudo-first order model. Further, the CNC@PPy exhibits an outstanding reusability, capable of maintaining 82.3% of its original Hg(II) adsorption capacity after five successive adsorption cycles. The findings of this work reveal a method to convert the agricultural by-product into high performance environmental remediation materials.

Highly selective adsorption of Hg (II) from aqueous solution by three-dimensional porous N-doped starch-based carbon

For the first time, N-doped carbon materials with 3D porous-layered skeleton structure was synthesized through a one-step co-pyrolysis method, which was fabricated by co-pyrolysis of natural corn starch and melamine using metal catalysts (Ni (II) and Mn (II)). The 3D-NC possessed a heterogeneously meso-macroporous surface with a hierarchically connected sheet structure inside. Batch adsorption experiments suggested that highly selective adsorption of Hg (II) by the 3D-NC could be completed within 90 min and had maximum adsorption capacities as high as 403.24 mg/g at 293 K, pH = 5. The adsorption mechanism for Hg (II) was carefully evaluated and followed the physical adsorption, electrostatic attraction, chelation, and ion exchange. Besides, thermodynamic study demonstrated that the Hg (II) adsorption procedure was spontaneous, endothermic, and randomness. More importantly, the 3D-NC could be regenerated and recovered well after adsorption-desorption cycles, showing a promising prospect in the remediation of Hg (II)-contaminated wastewater.

Nanofibrous/biopolymeric membrane a sustainable approach to remove organic micropollutants: A review

Aquifers are severely polluted with organic and inorganic pollutants, posing a serious threat to the global ecological system's balance. While various traditional methods are available, the development of innovative methods for effluent treatment and reuse is critical. Polymers have recently been widely used in a variety of industry sectors due to their unique properties. Biopolymers are a biodegradable material that is also a viable alternative to synthetic polymers. Biopolymers are preferably obtained from cellulose and carrageenan molecules from various biological sources. While compared with conventional non-biodegradable polymeric materials, the biopolymer possesses unique characteristics such as renewability, cost-effectiveness, biodegradability, and biocompatibility. The improvements towards the biopolymeric (natural) membranes have also been thoroughly discussed. The use of nanofillers to stabilise and improve the effectiveness of biopolymeric membranes in the elimination of organic pollutants is one of the most recent developments. This was discovered that the majority of biopolymeric membranes technology consolidated on organic pollutants. More research should be directed toward against emerging organic/persistent organic pollutants (POP) and micropollutants. Furthermore, processes for regenerating and reusing utilized biopolymer-based carbon - based materials are emphasized.

Recent Progress on Tailoring the Biomass-Derived Cellulose Hybrid Composite Photocatalysts

Biomass-derived cellulose hybrid composite materials are promising for application in the field of photocatalysis due to their excellent properties. The excellent properties between biomass-derived cellulose and photocatalyst materials was induced by biocompatibility and high hydrophilicity of the cellulose components. Biomass-derived cellulose exhibited huge amount of electron-rich hydroxyl group which could promote superior interaction with the photocatalyst. Hence, the original sources and types of cellulose, synthesizing methods, and fabrication cellulose composites together with applications are reviewed in this paper. Different types of biomasses such as biochar, activated carbon (AC), cellulose, chitosan, and chitin were discussed. Cellulose is categorized as plant cellulose, bacterial cellulose, algae cellulose, and tunicate cellulose. The extraction and purification steps of cellulose were explained in detail. Next, the common photocatalyst nanomaterials including titanium dioxide (TiO2), zinc oxide (ZnO), graphitic carbon nitride (g-C3N4), and graphene, were introduced based on their distinct structures, advantages, and limitations in water treatment applications. The synthesizing method of TiO2-based photocatalyst includes hydrothermal synthesis, sol-gel synthesis, and chemical vapor deposition synthesis. Different synthesizing methods contribute toward different TiO2 forms in terms of structural phases and surface morphology. The fabrication and performance of cellulose composite catalysts give readers a better understanding of the incorporation of cellulose in the development of sustainable and robust photocatalysts. The modifications including metal doping, non-metal doping, and metal-organic frameworks (MOFs) showed improvements on the degradation performance of cellulose composite catalysts. The information and evidence on the fabrication techniques of biomass-derived cellulose hybrid photocatalyst and its recent application in the field of water treatment were reviewed thoroughly in this review paper.

Engineered biochar supported layered double hydroxide-cellulose nanocrystals composite-: Synthesis, characterization and azo dye removal performance

In this work, engineered biochar decorated layered double hydroxides and cellulose nanocrystals (B-CuFe-CNC) biocomposites were synthesized by the facile ultrasonicated-co-precipitation technique. The biocomposite was investigated for purification of Eriochrome Black T (EBT) dye from water. The characterization results showed that the presence of CNC in biochar-layered double hydroxides resulted in a two-dimensional rod-like structure with excellent crystallinity, improved surface functionalities, and provides an attractive platform for the enhanced adsorption of azo anionic dye molecules. The adsorption system was appropriately demonstrated by the BBD-RSM (R² > 0.994). The biocomposite exhibited higher EBT adsorption in the acidic pH range (2-5) due to strong electrostatic and chemical interactions. The kinetic and isotherm results were well demonstrated by pseudo-second order, Freundlich, and Redlich Peterson models. The maximum adsorption capacity of biocomposite was 876.2 mg/g achieved within 45 min. The spectroscopic analyses imply that the high removal of EBT by biocomposite is mainly governed by electrostatic attraction, hydrogen bonding, and chemical/metal complexation mechanisms. The biocomposite maintained high EBT removal after six successive adsorption cycles and excellent dye adsorption in the different water matrices. The results suggest that tailoring biochar properties with layered double hydroxide and CNC is a promising way for the enhanced removal of dye contaminants from wastewater.

Advances in bioremediation of emerging contaminants from industrial wastewater by oxidoreductase enzymes

The bioremediation of emerging recalcitrant pollutants in wastewater via enzyme biotechnology has been evolving as cost-effective with an input of low-energy technological approach. However, the enzyme based bioremediation technology is still not fully developed at a commercial level. The oxidoreductases being the domineering biocatalysts are promising candidates for wastewater treatments. Henceforth, comprehending their global market and biotransformation efficacy is mandatory for establishing these techno-economic bio-enzymes in commercial scale. The biocatalytic strategy can be established as a combinatorial approach with existing treatment technology to achieve towering bioremediation and effective removal of emerging pollutants from wastewater. This review provides a novel insight on the toxicological xenobiotics released from industries such as paper and pulps, soap and detergents, pharmaceuticals, textiles, pesticides, explosives and aptitude of peroxidases, nitroreductase and cellobiose dehydrogenase in their bio-based treatment. Moreover, the review comprehensively covers environmental relevance of wastewater pollution and the critical challenges based on remediation achieved through biocatalysts for future prospectives.

Fabrication of Janus-type nanocomposites from cellulose nanocrystals for self-healing hydrogels' flexible sensors

Janus bio-nanomaterials have great application potential in functional solid surfactants, probes and flexible sensors. In this manuscript, the sustainable Janus cellulose nanocrystals-type (CNCs-type) nanomaterials were prepared by Pickering emulsion template method. The asymmetric functionalism of Janus nanorods was realized by asymmetrically grafting polypyrrole (PPy) and polydopamine (PDA) onto different sides of CNCs (Janus CNCs-PPy /PDA (JCNs)). JCNs was successfully applied to self-healing nanocomposite hydrogels and further applied to the development of flexible sensors. The self-healing efficiency of nanocomposite hydrogels was 87.2%, and the stress and strain reached 3.50 MPa and 453.45%, respectively. It is worth noting that flexible sensors have been widely used in the field of wearable electronic sensing for real-time monitoring of human movement due to their high sensitivity (gauge factor (GF) = 9.9) and fast response time (260 ms).

Isolation and Characterization of Cellulose Nanocrystals from Date Palm Waste

This study presents the isolation, characterization, and kinetic analyses of cellulose nanocrystals (CNCs) from date palm waste in the United Arab Emirates. After bleaching date palm stem waste with acidified NaClO₂ and delignification via NaOH treatments, cellulose was extracted. Mineral acid hydrolysis (62 wt % H₂SO₄) was performed at 45 °C for 45 min to produce crystalline nanocellulose. Fourier transform infrared (FTIR) and chemical composition analysis confirmed the removal of noncellulosic constituents. The crystallinity index increased gradually with chemical treatments, according to the obtained X-ray diffraction (XRD) results. Thermogravimetric analysis and differential scanning calorimetry results revealed that the CNC has high thermal stability. The Coats-Redfern method was used to determine the kinetic parameters. The kinetic analysis confirmed that CNC has more activation energy than cellulose and thus confirms its compact and resistive crystalline structure. This has been attributable to the stronger hydrogen bonding in CNC crystalline domains than that in cellulose crystalline domains. Scanning electron microscopy revealed that lignin and hemicellulose were eliminated after chemical pretreatments, and CNC with a rodlike shape was obtained after hydrolysis. Moreover, transmission electron microscopy confirmed the nanoscale of crystalline cellulose. ζ potential analysis indicated that the CNC afforded a stable suspension (-29.27 mV), which is less prone to flocculation. Kinetic analyses of cellulose and cellulose nanocrystals isolated from date palm waste are useful for making composites and designing selective pyrolysis reactors.

Removal of both anionic and cationic dyes from wastewater using pH-responsive adsorbents of L-lysine molecular-grafted cellulose porous foams

High adsorption efficiency, active to both anionic and cationic dyes and simple desorption are three main challenges of the existed adsorbents for decolorization of the dye-contained wastewaters. Porous foams based on L-lysine (Lys) molecular-grafted cellulose were firstly designed and fabricated to overcome those challenges. Cellulose were grafted with Lys in 1-butyl-3-methylimidazolium chloride (BMIMCl) via a chemical connection resulted from glycidyl methacrylate (GMA). The synthesized cellulose derivative (Cell-g-PGMA-Lys) was regenerated in the morphology of foam by non-solvent induced phase inversion from the BMIMCl-based solutions. The presence of Lys moieties and porous structure of Cell-g-PGMA-Lys were confirmed with a series of instrumental analysis. Both anionic reactive brilliant red X-3B (RBR X-3B) and cationic methylene blue (MB) were effectively adsorbed on and desorbed from Cell-g-PGMA-Lys by adjusting the solution pH value. Cell-g-PGMA-Lys had higher adsorption capacities than most of the reported adsorbents and was easy to separate from the decolorized water. It could be reused many times with little reduction of the adsorption capacity, which remained 86.9% and 92.5% for RBR X-3B and MB respectively after six adsorption-desorption cycles. The isothermal and kinetic adsorption proved that dyes were adsorbed single-layered on Cell-g-PGMA-Lys depending upon the electrostatic interaction between adsorbent and adsorbate.

Synthesis and characterisation of zinc oxide modified biorenewable polysaccharides based sustainable hydrogel nanocomposite for Hg2+ ion removal: Towards a circular bioeconomy

Industrial metal ion pollution has been considered the chief source of water contaminants all over the world. In the present research, we have prepared gum tragacanth cross-linked 2-hydroxyethyl methacrylate-co-acrylamide (GT-cl-(HEMA-co-AAm)) hydrogel and gum tragacanth cross-linked 2-hydroxyethyl methacrylate-co-acrylamide/zinc oxide (GT-cl-(HEMA-co-AAm)/ZnO) hydrogel composite with better Hg²⁺ adsorption capability. GT-cl-(HEMA-co-AAm)/ZnO hydrogel composite (154.8 mg g^-1) exhibited higher Hg²⁺ adsorption than GT-cl-(HEMA-co-AAm) hydrogel. To address the performance of GT-cl-(HEMA-co-AAm) hydrogel and GT-cl-(HEMA-co-AAm)/ZnO hydrogel composite, batch adsorption experiments were successfully conducted under different optimised conditions. At last, in-vitro antibacterial activities of Hg²⁺ loaded GT-cl-(HEMA-co-AAm) and GT-cl-(HEMA-co-AAm)/ZnO were performed in two different well Staphylococcus aureus (gram-positive) and Pseudomonas aeruginosa (gram-negative) bacteria. As a positive control, ampicillin was employed against both types of bacteria. This methodology for the reusability of material has a great ecofriendly impression for minimising secondary waste derived from adsorption and can help design upgraded antibacterial agents.

Synthesis of two novel bio-based hydrogels using sodium alginate and chitosan and their proficiency in physical immobilization of enzymes

Herein, four novel and bio-based hydrogel samples using sodium alginate (SA) and chitosan (CH) grafted with acrylamide (AAm) and glycidyl methacrylate (GMA) and their reinforced nanocomposites with graphene oxide (GO) were synthesized and coded as SA-g-(AAm-co-GMA), CH-g-(AAm-co-GMA), GO/SA-g-(AAm-co-GMA), and GO/CH-g-(AAm-co-GMA), respectively. The morphology, net charge, and water absorption capacity of samples were entirely changed by switching the biopolymer from SA to CH and adding a nano-filler. The proficiencies of hydrogels were compared in the immobilization of a model metagenomic-derived xylanase (PersiXyn9). The best performance was observed for GO/SA-g-poly(AAm-co-GMA) sample indicating better stabilizing electrostatic attractions between PersiXyn9 and reinforced SA-based hydrogel. Compared to the free enzyme, the immobilized PersiXyn9 on reinforced SA-based hydrogel showed a 110.1% increase in the released reducing sugar and almost double relative activity after 180 min storage. While immobilized enzyme on SA-based hydrogel displayed 58.7% activity after twelve reuse cycles, the enzyme on CH-based carrier just retained 8.5% activity after similar runs.

Recent Developments in the Removal of Dyes from Water by Starch-Based Adsorbents

Starch-based adsorbents have demonstrated excellent potential for the removal of various noxious dyes from wastewater. This review critically evaluates the recent progress in applications of starch-based adsorbents for the removal of dyes from water. The synthesis methods of starch-based composites and their effects on physicochemical characteristics of produced adsorbents are discussed. The removal of various dyes by starch-based adsorbents are described in detail, with emphasis on the effect of key parameters, adsorption mechanism and their reusability potential. The key challenges related to the synthesis and applications of starch-based adsorbents in water purification are highlighted. Based on the research gaps, recommendations for future research are made. The evaluation of starch-based adsorbents would contribute to the development of sustainable water treatment options in near future.

Adsorption of cationic dyes onto carrageenan and itaconic acid-based superabsorbent hydrogel: Synthesis, characterization and isotherm analysis

Polysaccharide-based hydrogels offer a great overlook for environmental applications and help in the elimination of various noxious pollutants from the water system. Novel carrageenan and itaconic acid-based superadsorbent hydrogel having appreciable swelling properties and adsorption capacity towards Methylene blue (MB), Crystal violet (CV), and Methyl Red (MR) was synthesized by suspension polymerization technique. The swelling study showed the dependency upon the temperature in which the swelling rate increased with increasing temperature with a maximum swelling rate of 417% at 318 K. For ascertaining the maximum adsorption capacity, various influential parameters such as contact time, adsorbent dose, dye concentration, and temperature were systematically studied. Maximum adsorption capacity as calculated from the Langmuir isotherm was 2439.02, 1111.11, and 666.68 mg/g for MB, CV, and MR, respectively. Thermodynamic studies revealed the spontaneous nature of the undertaken dye adsorption experiment. Overall, the present study reveals that the synthesized superadsorbent hydrogel can be used as an efficient adsorbent for the removal of dyes from an aqueous solution.

Synthesis of natural starch from Elaeis guineensis trunk biomass applying bisulphite steeping method: Optimization by RSM

A massive quantity of Elaeis guineensis (oil palm) trunk biomass, containing a significant amount of natural starch, is available in Malaysia as biowaste because of annual replantation. The efficient extraction of this starch (carbohydrate polymer) would be worthwhile concerning the environmental sustainability and economy through conversion to bioresources. This study investigated the effectiveness of the bisulfite steeping method for starch synthesis from oil palm trunk (OPT) biowaste. The central composite design (CCD) of Design-Expert software executed an experimental model design, data analysis, evaluated the impacts of process variables and their interaction through response surface methodology to optimize the bisulfite steeping method for starch synthesis. The developed quadratic models for four factors (strength of sodium bisulfite solution, steeping hour, mixing ratio with the bisulfite solution, and ultrapure water) and one response (%Yield) demonstrated that a significant starch yield (13.54%) is achievable employing 0.74% bisulfite solution, 5.6 steeping hours, for 1.6 and 0.6 mixing ratio with the bisulfite solution and ultrapure water respectively. Experimental outcomes were consistent with the predicted model, which eventually sustains the significance of this method. Malvern Zetasizer test revealed a bimodal granular distribution for starch, with 7.15 µm of hydrodynamic size. Starch morphology was determined by scanning electron microscopy. X-ray diffraction investigation exhibits an A-type model, specifying persistent characteristics, while FTIR confirms the presence of hydroxyl, carboxylic, and phenolic groups like other cereal starches.Implications: Malaysia is the 2nd largest palm oil exporter in the world. About 110 million tons of palm oil trunk (OPT) biomass is available annually during replanting activities. Modification of bio-wastes into a beneficial form (only 22% presently) like starch extraction would ensure potential reuse as a natural coagulant for wastewater and leachate treatment, food source, adhesives towards boosting the country's economy by sustainable waste management. The current study achieved better starch yield (13.54%) than previous, from the OPT biomass through the novel bisulfite steeping method. Therefore, this method will ascertain the effective implication of numerous economic activities.

Adsorptive removal of organic pollutant methylene blue using polysaccharide-based composite hydrogels

Methylene blue (MB) is categorized as an organic dye (OD) released as effluents after various industrial activities and is one of the most abundant pollutants in the aquatic environment. Significantly, because of its potential toxicity, removing MB from wastewater has been a matter of necessity in recent times. Numerous analytical techniques have been applied, among which polysaccharide-based composite hydrogels appear as the most favorable for MB removal because of their large surface area, excellent mechanical properties, swelling capability, and large-scale production. In this review, the first section gives adequate information about the ODs' adverse effects on the environment and the contribution of polysaccharide-based hydrogels for OD removal, especially MB. Next, various mechanisms such as electrostatic interactions, π-π interactions, hydrogen bonding, hydrophobic interaction, van der Waals force, and coordination interaction involved in the adsorption technique are investigated. The third section extensively describes the MB removal by incorporation of various materials such as monomers, metal oxides, magnetic nanoparticles, and clay into the polysaccharide matrix to produce composite hydrogels. Finally, the current limitations and future perspectives of the polysaccharide-based composite hydrogel techniques are addressed. Overall, this review acknowledged the vital role of polysaccharide-based composite hydrogels for MB adsorption by surveying 110 research articles published in the past five years (2015-2021).

A critical review on the techniques used for the synthesis and applications of crystalline cellulose derived from agricultural wastes and forest residues

In order to meet the growing energy crisis of the 21st century, the utilization of bio-based materials has become a field of high research endeavour. In view of that, the present review paper is focused on different techniques that are frequently explored for the synthesis of value-added crystalline derivatives of cellulose like MCC and NCC from agricultural wastes and forest residues. Moreover, a comparative analysis between thermochemical and biochemical methods is carried out for such valorization of biomass considering the mechanism involved with various reactions. Further, a critical analysis is performed on various individual techniques specifically used for the applications of MCC and NCC in different fields including environmental, polymer industry, pharmaceutical and other emerging sectors. This article will assist the readers not only to explore new biomass sources but also provides an in-depth insight on various green and cost-effective methods for sustainable production of crystalline cellulose.

Facile synthesis of amine-crosslinked starch as an efficient biosorbent for adsorptive removal of anionic organic pollutants from water

Developing applicable biosorbents for adsorptive removal of organic pollutants from water is highly demanded. However, most biosorbents suffer poor adsorption capability for anionic organic pollutants due to their negatively charged surface. Herein, we present a facile method to synthesize amine-crosslinked starch (ACS) biosorbent for removing anionic organic pollutants. The adsorption properties of ACS were thoroughly evaluated by selecting anionic brilliant blue (BB), amaranth (ART), diclofenac sodium (DS) as representatives. The results show that the ACS can selectively adsorb anionic molecules with large adsorption capacity and fast removal rate. The adsorption kinetic and isotherm behaviors can be well described by the pseudo-second-order and Langmuir models, respectively. The maximum uptake capacity of ACS for BB, ART and DS is as high as 1287.7, 724.6 and 595.2 mg g^-1, respectively. Moreover, the ACS can be easily regenerated and still exhibits favorable adsorption performance even after reusing for five times.

Development of Arabic gum-based AgTiO2 nanocomposite hydrogel as high efficient adsorbent of cationic dye methylene blue from water

The chemically crosslinked silver titanium dioxide embedded Arabic gum grafted polyacrylamide-polyacrylonitrile nanocomposite AgTiO₂@AG-g-P(AM-co-AN)was successfully synthesized and investigated by ATR-IR, XRD, and SEM. The synthesis optimization parameters of AG-g-P(AM-co-AN)were 5% AG, 1/0.5 AM/AN monomer molar ratio, 0.5 mg MBA cross-linker, and AgTiO₂ content (1%) gives AgTiO₂@AG-g-P(AM-co-AN) nanocomposite. While adsorption studies for AgTiO₂@AG-g-P(AM-co-AN) exhabited the maximum adsorption capacity (104.50 ± 3.02 mg/g) at concentration (150 mg/L), MB concentration (15 mg/L) and pH (8.0). The adsorption nonlinear kinetics models were used. Pseudo-second order governs the adsorption process, and the Langmuir model is more suited than Freundlich and Temkin.