Construction of an enzyme-based all-fiber SPR biosensor for detection of enantiomers

Efficient Electrochemical Coupling of Aptamer to Nanoelectrode for In Situ Detection of ATP in Single Cells

Nanoelectrodes, renowned for their small size, rapid mass transport, fast response, and high spatiotemporal resolution, have been recognized as a powerful tool in biosensing, especially for single-cell analysis. However, the nanoelectrode itself has no selectivity and cannot respond to nonelectroactive substances, limiting its wide application to some extent. Herein, we propose a simple and efficient electrochemical conjugation strategy to develop an electrochemical aptamer-coupled (E-AC) sensor for detecting adenosine triphosphate (ATP) in single living cells. Through simple electrochemical conjugation, ferrocene-labeled aptamers could be stably and efficiently coupled onto the surface of carbon fiber electrodes within 5 min. The small size (ca. 400 nm) and biocompatibility of the functionalized nanoelectrodes enabled the E-AC sensors to noninvasively and continuously monitor ATP content in single HeLa cells over 20 min, as well as the cellular ATP fluctuations under glucose starvation. Furthermore, the E-AC sensors exhibit superior specificity, sensitivity, and universality in the application of analysis of ATP in single living Hela cells and MCF-7 cells. They were also versatile for sensing other nonelectroactive targets through modification of the corresponding electroactive marker-labeled aptamers, showing great potential in cell-related physiological processes and drug screening.

Use of Laccase Enzymes as Bio-Receptors for the Organic Dye Methylene Blue in a Surface Plasmon Resonance Biosensor

Methylene blue is a cationic organic dye commonly found in wastewater, groundwater, and surface water due to industrial discharge into the environment. This emerging pollutant is notably persistent and can pose risks to both human health and the environment. In this study, we developed a Surface Plasmon Resonance Biosensor employing a BK7 prism coated with 3 nm chromium and 50 nm of gold in the Kretschmann configuration, specifically for the detection of methylene blue. For the first time, laccases immobilized on a gold surface were utilized as bio-receptors for this organic dye. The enzyme was immobilized using carbodiimide bonds with EDC/NHS crosslinkers, allowing for the analysis of samples with minimal preparation. The method demonstrated validation with a limit of detection (LOD) of 4.61 mg L-1 and a limit of quantification (LOQ) of 15.37 mg L-1, a working range of 0-100 mg L-1, and an R2 value of 0.9614 during real-time analysis. A rainwater sample spiked with methylene blue yielded a recovery rate of 122.46 ± 4.41%. The biosensor maintained a stable signal over 17 cycles and remained effective for 30 days at room temperature.

Surface electric field enhanced biosensor based on symmetrical U-tapered HCF structure for gastric carcinoma biomarker trace detection

In this article, a novel U-tapered hollow-core fiber (HCF) surface plasmon resonance (SPR) biosensor coated with PtS2 for early-stage gastric carcinoma (GC) diagnosis was demonstrated. The article proposed the first investigation to detect Interleukin-10 (IL10) and Interleukin-1β (IL1β) which were associated with the risk of developing gastric carcinoma, using optical fiber SPR technology. Herein, the sensitivity of sensor was effectively improved through a combination of tapered and U-shaped structures. Additionally, to further enhance the detection capability, two-dimensional material PtS2 was utilized to increase the surface electric field intensity of the sensor. Simultaneously, optimization of structural parameters such as taper ratio, bending diameters, and Au film thickness was conducted. Ultimately, the designed sensor achieved a remarkable sensitivity of 13210 nm/RIU within the refractive index (RI) range of 1.33-1.37. The sensor demonstrated exceptional performance, achieving sensitivities of 3.64 nm/(ng/ml) and 7.46 nm/(ng/ml) for the detection of IL10 and IL1β biomarkers, respectively, along with limit of detection (LOD) of 2.74 pg/ml and 1.33 pg/ml, and successfully detecting the presence of these biomarkers in the serum of gastric cancer patients. Overall, the proposed sensor exhibits significant potential in early gastric cancer detection and advances the application of optical fiber SPR sensors in trace biodetection.

Synthesis of chiral graphene structures and their comprehensive applications: a critical review

From a molecular viewpoint, chirality is a crucial factor in biological processes. Enantiomers of a molecule have identical chemical and physical properties, but chiral molecules found in species exist in one enantiomer form throughout life, growth, and evolution. Chiral graphene materials have considerable potential for application in various domains because of their unique structural framework, properties, and controlled synthesis, including chiral creation, segregation, and transmission. This review article provides an in-depth analysis of the synthesis of chiral graphene materials reported over the past decade, including chiral nanoribbons, chiral tunneling, chiral dichroism, chiral recognition, and chiral transfer. The second segment focuses on the diverse applications of chiral graphene in biological engineering, electrochemical sensors, and photodetectors. Finally, we discuss research challenges and potential future uses, along with probable outcomes.

Functionalized Chiral Materials for Use in Chiral Sensors

Chirality represents a fundamental attribute within living systems and is a pervasive phenomenon in the natural world. The identification and analysis of chiral materials within natural environments and biological systems hold paramount importance in clinical, chemical, and biological sciences. Within chiral analysis, there is a burgeoning focus on developing chiral sensors exhibiting exceptional selectivity, sensitivity, and stability, marking it as a forefront area of research. In the past decade (2013-2023), approximately 1990 papers concerning the application of various chiral materials in chiral sensors have been published. Biological materials and nanomaterials have important applications in the development of chiral sensors, which accounting for 26.67% and 45.24% of the material-related applications in these sensors, respectively; moreover, the development of chiral nanomaterials is closely related to the development of portable and stable chiral sensors. Natural chiral materials, utilized as selective recognition units, are combined with carriers characterized by good physical and chemical properties through functionalization to form various functional chiral materials, which improve the recognition efficiency of chiral sensors. In this article, from the perspective of biological materials, polymer materials, nanomaterials, and other functional chiral materials, the applications of chiral sensors are summarized and the research prospects of chiral sensors are discussed.

The potential of a novel enzyme-based surface plasmon resonance biosensor for direct detection of dopamine

Dopamine is one of the significant neurotransmitters and its monitoring in biological fluids is a critical issue in healthcare and modern biomedical technology. Here, we have developed a dopamine biosensor based on surface plasmon resonance (SPR). For this purpose, the carboxymethyl dextran SPR chip was used as a surface to immobilize laccase as a bioaffinity recognition element. Data analysis exhibited that the acidic pH value is the optimal condition for dopamine interaction. Calculated kinetic affinity (KD) (48,545 nM), obtained from a molecular docking study, showed strong association of dopamine with the active site of laccase. The biosensor exhibited a linearity from 0.01 to 189 μg/ml and a lower detection limit of 0.1 ng/ml (signal-to-noise ratio (S/N) = 3) that is significantly higher than the most direct dopamine detecting sensors reported so far. Experiments for specificity in the presence of compounds that can co-exist with dopamine detection such as ascorbic acid, urea and L-dopa showed no significant interference. The current dopamine biosensor with high sensitivity and specificity, represent a novel detection tool that offers a label-free, simple procedure and cost effective monitoring system.

Recent Progress in Detecting Enantiomers in Food

The analysis of enantiomers in food has significant implications for food safety and human health. Conventional analytical methods employed for enantiomer analysis, such as gas chromatography and high-performance liquid chromatography, are characterized by their labor-intensive nature and lengthy analysis times. This review focuses on the development of rapid and reliable biosensors for the analysis of enantiomers in food. Electrochemical and optical biosensors are highlighted, along with their fabrication methods and materials. The determination of enantiomers in food can authenticate products and ensure their safety. Amino acids and chiral pesticides are specifically discussed as important chiral substances found in food. The use of sensors replaces expensive reagents, offers real-time analysis capabilities, and provides a low-cost screening method for enantiomers. This review contributes to the advancement of sensor-based methods in the field of food analysis and promotes food authenticity and safety.

Surface-Enhanced Raman Scattering Enantioselective Detection of Gastric Cancer-Related d-Amino Acids in Saliva Based on Enzyme-Mediated Cascade Reaction

The unusual d-amino acids (d-AAs), as the counter enantiomer of usual l-amino acids (l-AAs), have evoked increasing attention because of their potential relevance with diseases. Accordingly, it is essential to establish sensitive and selective detection methods for d-AAs without the interferences from l-AAs. The surface-enhanced Raman scattering (SERS) technique is efficacious for the detection of molecules but routinely ineffective in enantiomeric differentiation. d-Proline (d-Pro) and d-alanine (d-Ala) are regarded as biomarkers of gastric cancer. Herein, Raman-active boronate modified SERS chips are constructed to develop a d-amino acid oxidase (DAAO)-mediated cascade reaction-based SERS enantioselective assay for d-Pro and d-Ala. The principle is that DAAO selectively catalyzes the deamination of d-Pro and d-Ala, and the produced H2O2 oxidizes boronate to present a new SERS peak at 883 cm-1 for quantitative analysis in a ratiometric way. A linear range from 20 to 400 μmol/L and a limit of detection down to 14.8 μmol/L are reached. In addition, interferences from l-AAs and many other possible species coexisting in biofluids with the detection of d-Pro and d-Ala are ignorable. Enzyme-mediated cascade reaction-based SERS chips are further utilized for saliva sample analysis, and the total levels of d-Pro and d-Ala in salivary samples from gastric cancer patients are much higher than those of healthy persons. This work provides a solution for SERS enantioselective analysis and noninvasive screening chiral biomolecules for disease diagnosis.

Polarization-independent tilted fiber Bragg grating surface plasmon resonance sensor based on spectrum optimization

We experimentally demonstrated polarization multiplexing schemes in a tilted fiber grating (TFBG) to achieve polarization-independent fiber-optic surface plasmon resonance (SPR) sensors. The first used two orthogonal polarized lights separated by a polarization beam splitter (PBS) that are p-polarized in polarization-maintaining fiber (PMF) and precisely aligned with the tilted grating plane, so as to achieve the transmission of p-polarized light in two opposite directions of the Au-coated TFBG to excite SPR. Alternatively, polarization multiplexing was also achieved by exploring two polarization components to achieve the SPR effect through a Faraday rotator mirror (FRM). The SPR reflection spectra are polarization-independent of the light source and any perturbations to fibers, which are explained by the superposition of p- and s-polarized transmission spectra in equal proportions. The spectrum optimization is presented to reduce the proportion of the s-polarization component. A polarization-independent TFBG-based SPR refractive index (RI) sensor with a wavelength sensitivity of 555.14 nm/RIU and an amplitude sensitivity of 1724.92 dB/RIU for small changes is obtained, exhibiting unique advantages of minimizing the polarization alterations by mechanical perturbations.

Strategies for Surface Design in Surface Plasmon Resonance (SPR) Sensing

Surface plasmon resonance (SPR) comprises several surface-sensitive techniques that enable the trace and ultra-trace detection of various analytes through affinity pairing. Although enabling label-free, sensitive detection and real-time monitoring, several issues remain to be addressed, such as poor stability, non-specific adsorption and the loss of operational activity of biomolecules. In this review, the progress over sensor modification, immobilization techniques and novel 2D nanomaterials, gold nanostructures and magnetic nanoparticles for signal amplification is discussed. The advantages and disadvantages of each design strategy will be provided together with some of the recent achievements.

Tailoring Galactose Oxidase for Self-Powered Benzyl Alcohol Sensing

Benzyl alcohol (BnOH) is a widely-used preservative in a variety of cosmetics, but the excess addition (≥1.0 %) may cause strong symptoms such as nausea, gastrointestinal irritation, convulsion, even death, making it crucial to monitor and control the addition quantity. Herein, we have developed a test-strip-like BnOH detection method via tailoring a galactose oxidase (GOase) towards BnOH oxidation and preparing a self-powered electrochromic strip for BnOH concentration visualization. A double-substituted GOase variant (Y329S/R330F), on the basis of the reported GOase M₁ , has been obtained by semi-rational design with a 24.6-fold improved activity towards BnOH compared to GOase M₁ . The GOase Y329S/R330F electrode has a response to BnOH with a linear range of 0.04 to 3.25 mM (R² =0.9985), a sensitivity of 122.78 μA mM^-1  cm^-2 , and a detection limit of 0.03 mM (S/N=3). Coupling an electrochromic Prussian blue (PB) cathode helps the successful sensing visualization without any further power supply. The present sensing is more convenient and user-friendly than the generally used gas chromatography (GC) and high performance liquid chromatography (HPLC), and brings a more accessible solution to the field of quality controlling.

Microfluidic preparation of optical sensors for biomedical applications

Optical biosensors are platforms that translate biological information into detectable optical signals, and have extensive applications in various fields due to their characteristics of high sensitivity, high specificity, dynamic sensing, etc. The development of optical sensing materials is an important part of optical sensors. In this review, we emphasize the role of microfluidic technology in the preparation of optical sensing materials and the application of the derived optical sensors in the biomedical field. We first present some common optical sensing mechanisms and the functional responsive materials involved. Then, we describe the preparation of these sensing materials by microfluidics. Afterward, we enumerate the biomedical applications of these optical materials as biosensors in disease diagnosis, drug evaluation, and organ-on-a-chip. Finally, we discuss the challenges and prospects in this field.

Applications of Optical Fiber in Label-Free Biosensors and Bioimaging: A Review

Biosensing and bioimaging are essential in understanding biological and pathological processes in a living system, for example, in detecting and understanding certain diseases. Optical fiber has made remarkable contributions to the biosensing and bioimaging areas due to its unique advantages of compact size, immunity to electromagnetic interference, biocompatibility, fast response, etc. This review paper will present an overview of seven common types of optical fiber biosensors and optical fiber-based ultrasound detection in photoacoustic imaging (PAI) and the applications of these technologies in biosensing and bioimaging areas. Of course, there are many types of optical fiber biosensors. Still, this paper will review the most common ones: optical fiber grating, surface plasmon resonance, Sagnac interferometer, Mach-Zehnder interferometer, Michelson interferometer, Fabry-Perot Interferometer, lossy mode resonance, and surface-enhanced Raman scattering. Furthermore, different optical fiber techniques for detecting ultrasound in PAI are summarized. Finally, the main challenges and future development direction are briefly discussed.

Advances in Novel Nanomaterial-Based Optical Fiber Biosensors-A Review

This article presents a concise summary of current advancements in novel nanomaterial-based optical fiber biosensors. The beneficial optical and biological properties of nanomaterials, such as nanoparticle size-dependent signal amplification, plasmon resonance, and charge-transfer capabilities, are widely used in biosensing applications. Due to the biocompatibility and bioreceptor combination, the nanomaterials enhance the sensitivity, limit of detection, specificity, and response time of sensing probes, as well as the signal-to-noise ratio of fiber optic biosensing platforms. This has established a practical method for improving the performance of fiber optic biosensors. With the aforementioned outstanding nanomaterial properties, the development of fiber optic biosensors has been efficiently promoted. This paper reviews the application of numerous novel nanomaterials in the field of optical fiber biosensing and provides a brief explanation of the fiber sensing mechanism.

TiO2 Nanotubes Decorated with CdSe Quantum Dots: A Bifunctional Electrochemiluminescent Platform for Chiral Discrimination and Chiral Sensing

Chiral analysis is of significant importance for living organisms since chirality is the fundamental phenomenon in nature. In this work, a bifunctional electrochemiluminescent (ECL) platform is constructed for chiral discrimination and chiral sensing. 3-Mercaptopropionic acid-functionalized CdSe quantum dots (CdSe QDs) are combined with aminated TiO₂ nanotubes (NH₂-TiNTs) via amidation. The resultant CdSe QDs/TiNTs display significantly enhanced ECL signals due to the synergistic effect between CdSe QDs and TiNTs, which are then used for the chiral discrimination of the isomers of nine chiral amino acids (AAs) in the presence of d-AA oxidase (DAAO). DAAO can selectively catalyze the oxidation of d-AAs to generate H₂O₂, which acts as the coreaction reagent and triggers the ECL signals of CdSe QDs/TiNTs, and thus, the isomers of the nine chiral AAs can be effectively discriminated. In addition, the as-constructed ECL platform can also be used for the sensitive detection of d-AAs in the presence of DAAO with a wide linear range and a low limit of detection. These findings suggest that the CdSe QDs/TiNTs can work as a bifunctional ECL platform (chiral discrimination and chiral sensing), which might be an advanced ECL platform for biomedical applications.