Preparation of millimeter-sized chitosan/carboxymethyl cellulose hollow capsule and its dye adsorption properties

Synergistic photocatalytic and adsorption capabilities of ZnO/chitosan/CMC for organic dye degradation under sunlight irradiation

The bionanomaterial for wastewater treatment attracts interest due to it is nontoxic and biodegradable. However, it has limitations cause of the weak chemical interaction, narrow surface area, and reusability of this material. In this study, a novel bionanomaterial for wastewater treatment was developed using a nontoxic and biodegradable carboxymethyl cellulose (CMC) base. To overcome the limitations of weak chemical interactions affecting its adsorption capacity and reusability, chitosan (CS) and ZnO nanoparticles with photocatalytic properties were incorporated. The resulting ZnO/CS/CMC nanocomposite exhibits dual functionality as a photocatalyst and adsorbent, enhancing the removal of methylene blue (MB) from wastewater. The material's morphology and physicochemical properties were thoroughly characterized using SEM, TEM, FTIR, XRD, BET, and DLS techniques. The molar ratio of ZnO (0.5-1.5) significantly influenced the nanocomposite's characteristics, with higher ZnO ratios producing a highly homogeneous spherical morphology and increased surface area. At a ZnO ratio of 1.5, the nanocomposite achieved outstanding photocatalytic performance, degrading 99.5 % of MB in just 60 min under sunlight irradiation. Additionally, the highest adsorption capacity of 4.66 mg g-1 followed the Langmuir isotherm model. This study highlights the enhanced MB removal efficiency due to the synergistic effect of ZnO particles and the supportive matrix. The developed material offers an eco-friendly, efficient, and sustainable solution for wastewater treatment, combining high performance with the benefits of biodegradability and reusability.

Preparation and Properties of Sodium Carboxymethyl Cellulose Microspheres by Dropping Method

Sodium carboxymethyl cellulose (CMC) is the most extensively utilized derivative of cellulose. In this study, an innovative approach was employed to disperse a CMC aqueous solution into olive oil in the form of liquid droplets, resulting in the direct formation of CMC microspheres after drying. The effects of CMC concentration and needle aperture size on microsphere formation were systematically investigated, showing that the particle size of the microspheres decreased with an increase in CMC concentration and a decrease in needle aperture. The CMC-based microspheres exhibited a consistently uniform spheroid morphology with particle sizes ranging from 1.5 to 2.5 mm, and a three-dimensional uniform polymeric network structure. Furthermore, the drug loading efficiency of the CMC-based olive oil microspheres reached 82.18%, which was markedly superior to that of other cellulose-based microspheres for fat-soluble substances. The CMC-based vitamin C (VC) microspheres exhibited an ultimate drug loading efficiency of approximately 24%, and their maximum encapsulation efficiency was 78.57% at a VC concentration of 30%, which was significantly higher than that of starch-based VC microspheres. Additionally, the CMC-based VC microspheres realized a sustained and stable release rate in ethanol at 30 °C.

In situ synthesis of MIL-125 on cinnamon stick and improved via carboxymethyl cellulose: A sustainable approach for super-high crystal violet adsorption

In the current study, a biowaste cinnamon stick (CS) was used as an adsorbent and modified via in-situ techniques with titanium-based metal organic framework (MIL-125@CS) and carboxymethyl cellulose (CMC/MIL-125@CS). The prepared samples were characterized by various techniques, then utilized for toxic crystal violet (CV) dye removal. CV adsorption was examined for the effects of adsorbent dosage, solution pH, contact time, initial concentration, temperature and anion/cation/natural organic material (NOM). CV removal rate remarkably decreased at low pHs due to the degradation of CV and wavelength shift in the strongly acidic region. The kinetic and isotherm results showed that CMC/MIL-125@CS reached equilibrium much faster (30 min) and much higher adsorption capacity (6750.58 mg/g) than CS and MIL-125@CS. Furthermore, the samples were efficiently regenerated and reusable over five cycles, demonstrating significant adsorption rates. Functional material design approaches yielded superior CV adsorption performance.

The adsorption behavior and mechanism of Cu(Ⅱ), Fe(Ⅱ) and Co(Ⅱ) on straw biochar and their Fenton-like performance for ciprofloxacin decontamination

In this study, the adsorption of aqueous Cu(Ⅱ), Fe(Ⅱ), and Co(Ⅱ) on biochars at diverse synthesized temperatures was evaluated. The optimal sample BC-800 achieved superior adsorption performance of Cu(Ⅱ), Fe(Ⅱ), and Co(Ⅱ) at 10-50 mg L-1 initial concentration. Due to the larger surface area (349.6 m2/g), total pore volume (0.24 cm3/g), average pore diameter (6.4 nm), higher degree of graphitization (IG/ID = 1.00) and stable aromatic carbon structure, BC-800 achieved excellent adsorption of Cu(Ⅱ), Fe(Ⅱ), and Co(Ⅱ) through multilayer chemical adsorption, corresponding to the pseudo-2nd-order and Freundlich model (Qm Cu(Ⅱ) = 433.4 mg g-1, Qm Fe(Ⅱ) = 472.0 mg g-1 and Qm Co(Ⅱ) = 301.0 mg g-1). After then, the adsorbed biochars with Cu(Ⅱ), Fe(Ⅱ), and Co(Ⅱ) were directly used as heterogeneous catalysts in Fenton-like reaction for ciprofloxacin (CIP) degradation. Compared with Co-BC-800/peroxymonosulfate (PMS) system, Co-BC-800/H2O2 system exhibited the 56.6% decontamination of CIP with lower ions leaching (0.53 mg/L) within 70 min. The 97.9% of CIP was finally removed by Co-BC-800/H2O2 under optimized conditions: initial pH = 6.94, catalyst dosage = 1.0 g L-1, H2O2 concentration = 0.44 g L-1. Furthermore, Co-BC-800 exhibited superior acid-base adaptability (2.94-10.94) and anti-anion interference ability. The removal of CIP was achieved by the synergistic effect of adsorption and oxidative degradation. This study proposes some insights into the behavior and mechanism of metal ions adsorption on biochar and hazardous waste treatment.

Force mechanism analysis of composite microbial dust suppressants based on extracellular polymeric substances (EPS) mode components

As an important potential dust suppression method, the slow onset time is one of the key factors that restrict the effect of microbial dust suppressant. In the early stage, we have confirmed that extracellular polymeric substances (EPS) can improve the dust suppression effect by wetting coal dust and increasing Ca2+ nucleation sites. Therefore, in this study, chitosan (CTS) and bovine serum albumin (BSA) in different ratios (CTS: BSA = 1:1, 1:2, 2:1) as model molecules of EPS were combined with Bacillus subtilis to prepare efficient and fast microbial dust suppressants. Furthermore, the interaction forces were analyzed through molecular dynamics simulation. Results showed that adding CTS and BSA would improve the dust suppression effect, and the dust suppression effect was the best when the ratio of CTS: BSA was 1:2. In addition, the contact angle decreased as the BSA content increased. The Fourier transform infrared spectroscopy (FTIR) results showed that when the ratio of CTS to BSA was 1:2, the dust suppressants were easier to interact with coal dust by the key functional groups and form calcite type CaCO3. The molecular dynamics simulation results showed that the main interaction was Van der Waals force. In addition, the interaction force was strongest when CTS: BSA was 1:2, increasing by 137% compared with the microbial dust suppressants without CTS or BSA. This study provides theoretical support for the development of efficient and rapid microbial dust suppressants.

Cutting-Edge Applications of Cellulose-Based Membranes in Drug and Organic Contaminant Removal: Recent Advances and Innovations

The increasing environmental challenges caused by pharmaceutical waste, especially antibiotics and contaminants, necessitate sustainable solutions. Cellulose-based membranes are considered advanced tools and show great potential as effective materials for the removal of drugs and organic contaminants. This review introduces an environmentally friendly composite membrane for the elimination of antibiotics and dye contaminants from water and food, without the use of toxic additives. The potential of cellulose-based membranes in reducing the impact on water quality and promoting environmental sustainability is emphasized. Additionally, the benefits of using biobased cellulose membranes in membrane biological reactors for the removal of antibiotics from pharmaceutical waste and milk are explored, presenting an innovative approach to achieving a circular economy. This review provides recent and comprehensive insights into membrane bioreactor technology, making it a valuable resource for researchers seeking efficient methods to break down antibiotics in industrial wastewater, particularly in the pharmaceutical and dairy industries.

Chitosan-based aerogels: A new paradigm of advanced green materials for remediation of contaminated water

Chitosan (CS) aerogels are highly porous (∼99 %), exhibit ultralow density, and are excellent sorbents for removing ionic pollutants and oils/organic solvents from water. Their abundant hydroxyl and amino groups facilitate the adsorption of ionic pollutants through electrostatic interaction, complexation and chelation mechanisms. Selection of suitable surface wettability is the way to separate oils/organic solvents from water. This review summarizes the most recent developments in improving the adsorption performance, mechanical strength and regeneration of CS aerogels. The structure of the paper follows the extraction of chitosan, preparation and sorption characteristics of CS aerogels for heavy metal ions, organic dyes, and oils/organic solvents, sequentially. A detailed analysis of the parameters that influence the adsorption/absorption performance of CS aerogels is carried out and their effective control for improving the performance is suggested. The analysis of research outcomes of the recently published data came up with some interesting facts that the unidirectional pore structure and characteristics of the functional group of the aerogel and pH of the adsorbate have led to the enhanced adsorption performance of the CS aerogel. Finally, the excerpts of the literature survey highlighting the difficulties and potential of CS aerogels for water remediation are proposed.

One-step fabrication of millimeter-scale hollow vesicles with chitosan /DADMAC/ sodium alginate graft copolymer for enhanced anionic dye adsorption

Hollow vesicles are promising in water treatment due to their unique structure of the membrane and inner cavity. However, the adsorption capacity needs to be improved for targeted pollutants. Herein, millimeter-scale hollow vesicles were prepared with a one-step process of sequential stirring and grafting using chitosan, diallyldimethylammonium chloride, and sodium alginate as raw materials with the purpose of efficient removal of anionic dyes from wastewater. The composite vesicles were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The hollow vesicles showed the structure of the cationic membrane and the inner cavity, facilitating the dye adsorption. The adsorption capacity for the anionic dye Reactive Black 5 reached 698.1 mg/g, more than twice that of the binary composite vesicles without graft. The adsorption kinetics and isotherm data coincided with the pseudo-second-order and Langmuir models, respectively, and the adsorption mechanism was monolayer chemisorption. Moreover, the vesicles worked well in wide ranges of environment pH, temperature, and co-existing pollutants. They also possessed excellent cyclic regeneration performance, in which 93 % of the initial adsorption capacity was maintained after four cycles. These results indicate that the millimeter-scale hollow vesicles exhibit broad application prospects for wastewater purification.

Adsorbents prepared from epoxy-based porous materials of microcrystalline cellulose for excellent adsorption of anionic and cationic dyes

It reported a porous material prepared from microcrystalline cellulose (MCC), to achieve rapid preparation of adsorbents. The porous material was characterized by several tools including 1H NMR, FTIR, XPS, and SEM. Two adsorbents were prepared and subjected to adsorption experiments. Dye adsorption experiments show that the adsorption driving is electrostatic interactions and the process is chemisorption. The maximum capacity of Microcrystalline cellulose-g-Poly (glycidyl methacrylate)-Tannins (MPT) reached 191.3 (Methylene blue), 123.7 mg g-1 (Rhodamine B), and Microcrystalline cellulose-g-Poly (glycidyl methacrylate)-Lysine (MPL) attained 425.8 (Methylene blue), 480.7 mg g-1 (Methyl orange). The results were followed the pseudo-second-order (PSO) and agreed with the Langmuir fit model. Adsorption-desorption cycling experiments further indicate that the adsorbent possesses outstanding reproducibility. At last, epoxidized bio-porous materials are positive in the preparation of dye adsorbents with critical adsorption properties.

Highly Efficient Biosorption of Cationic Dyes via Biopolymeric Adsorbent-Material-Based Pectin Extract Polysaccharide and Carrageenan Grafted to Cellulosic Nonwoven Textile

Water scarcity and contamination have emerged as critical global challenges, requiring the development of effective and sustainable solutions for the treatment of contaminated water. Recently, functionalized polymer biomaterials have garnered significant interest because of their potential for a wide range of water treatment applications. Accordingly, this paper highlights the design of a new adsorbent material based on a cellulosic nonwoven textile grafted with two extracted biopolymers. The layer-by-layer grafting technique was used for the polyelectrolyte multi-layer (PEM) biosorbent production. Firstly, we extracted a Suaeda fruticosa polysaccharide (SFP) and confirmed its pectin-like polysaccharide structure via SEC, NMR spectroscopy, and chemical composition analyses. Afterward, the grafting was designed via an alternating multi-deposition of layers of SFP polymer and carrageenan crosslinked with 1,2,3,4-butanetetracarboxylic acid (BTCA). FT-IR and SEM were used to characterize the chemical and morphological characteristics of the designed material. Chemical grafting via polyesterification reactions of the PEM biosorbent was confirmed through FT-IR analysis. SEM revealed the total filling of material microspaces with layers of grafted biopolymers and a rougher surface morphology. The assessment of the swelling behavior revealed a significant increase in the hydrophilicity of the produced adsorbent system, a required property for efficient sorption potential. The evaluation of the adsorption capabilities using the methylene blue (MB) as cationic dye was conducted in various experimental settings, changing factors such as the pH, time, temperature, and initial concentration of dye. For the untreated and grafted materials, the greatest adsorbed amounts of MB were 130.6 mg/g and 802.6 mg/g, respectively (pH = 4, T = 22 C, duration = 120 min, and dye concentration = 600 mg/L). The high adsorption performance, compared to other reported materials, was due to the presence of a large number of hydroxyl, sulfonate, and carboxylic functional groups in the biosorbent polymeric system. The adsorption process fitted well with the pseudo-first-order kinetic model and Langmuir/Temkin adsorption isotherms. This newly developed multi-layered biosorbent shows promise as an excellent adsorption resultant and cheap-cost/easy preparation alternative for treating industrial wastewater.

Carboxymethyl Cellulose/Polyacrylamide/Fe3O4 Magnetic Ion Imprinting Biosorbent for Removal and Recovery of La3

To use resources rationally, the recovery and recycling of rare earth (RE) from industrial sewage have attracted a lot of attention. Herein, a polymer adsorbent CMC/PAM/Fe3O4 (CPF) was synthesized from renewable carboxymethyl cellulose (CMC), polyacrylamide (PAM), and Fe3O4 by the template of La3+ using ion imprinting technology. The CPF was characterized with X-ray diffraction (XRD), IR, X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM), and results show that PAM and CMC can crosslink with each other and form copolymers with Fe3O4 particles dispersing in it. The adsorption properties for the template ions La3+ were fully studied. It is found that CPF exhibited good adsorption performance with an adsorption capacity of 34.6 mg·g-1. Cycling experiments show that CPF still has high efficiency even after 5 cycles. Meanwhile, the desorption rate can reach more than 98%. The low wastage and high adsorption/desorption efficiency would enable CPF to be a good candidate adsorbent for removal/recovery of La3+ from industrial sewage.

Chitosan/carboxymethylcellulose polyelectrolyte complexes (PECs) are an effective material for dye and heavy metal adsorption from water

Granular macroscopic chitosan/carboxymethylcellulose polyelectrolytic complexes (CHS/CMC macro-PECs) were produced and tested as adsorbents for six pollutants often present in wastewaters: sunset yellow (YS), methylene blue (MB), Congo red (CR) and safranin (S), cadmium (Cd²⁺) and lead (Pb²⁺). The optimum adsorption pH values at 25 °C were 3.0, 11.0, 2.0, 9.0, 10.0, and 9.0 for YS, MB, CR, S, Cd²⁺, and Pb²⁺, respectively. Kinetic studies indicated that the pseudos-econd order model best represented the adsorption kinetics of YS, MB, CR, and Cd²⁺, whereas the pseudo-first order model was the most suitable for S and Pb²⁺ adsorption. The Langmuir, Freundlich, and Redlich-Peterson isotherms were fitted to experimental adsorption data, with the Langmuir model providing the best fit. The maximum adsorption capacity (q_máx) of CHS/CMC macro-PECs for the removal of YS, MB, CR, S, Cd²⁺, and Pb²⁺ was 37.81, 36.44, 70.86, 72.50, 75.43, and 74.42 mg/g, respectively (corresponding to 98.91 %, 94.71 %, 85.73 %, 94.66 %, 98.46 %, and 97.14 %). Desorption assays showed that CHS/CMC macro-PECs can be regenerated after adsorbing any of the six pollutants studied, with possibility of reuse. These results provide an accurate quantitative characterization of the adsorption of organic and inorganic pollutants on CHS/CMC macro-PECs, indicating a novel technological applicability of these two inexpensive, easy-to-obtain polysaccharides for water decontamination.

Cellulose nanofibers decorated with SiO2 nanoparticles: Green adsorbents for removal of cationic and anionic dyes; kinetics, isotherms, and thermodynamic studies

Cellulose nanofibers decorated with SiO2 nanoparticles (SiO2-CNF) were prepared by the extraction of cellulose nanofibers from Yucca leaves, followed by modification with SiO2 nanoparticles, and used as efficient materials for the removal of both anionic and cationic dyes from the aqueous solution. Prepared nanostructures were characterized using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction powder (XRD), Thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), and transmission electron microscopy (TEM) analysis. The adsorption capacity of the nanostructures was investigated for the removal of both cationic (Methylene Blue, MB, and Crystal Violet, CV) and anionic (Eriochrome Black-T, EB) dyes. The kinetics of adsorption were investigated using some well-known models, including intraparticular diffusion (IPD), pseudo-first-order (PFO), pseudo-second-order (PSO), and Elovich. The adsorption isotherms were also explored using the Langmuir, Freundlich, Temkin, and Redlich-Peterson models. The obtained results revealed that the adsorption processes follow PSO kinetic and Langmuir isotherm models. Thermodynamic parameters of the adsorption were measured at different temperatures, indicating the feasibility and spontaneity of the adsorption. The pH and salt effects on adsorption were also explored. Finally, according to the reusability tests, the prepared adsorbents showed high recoverability without considerable loss in adsorption efficiency after five repeated runs.

Enhancing Pullulan Soft Capsules with a Mixture of Glycerol and Sorbitol Plasticizers: A Multi-Dimensional Study

The plasticizer is crucial in the plant-based soft capsule. However, meeting the quality requirements of these capsules with a single plasticizer is challenging. To address this issue, this study first investigated the impact of a plasticizer mixture containing sorbitol and glycerol in varying mass ratios and the performance of the pullulan soft film and capsule. The multiscale analysis demonstrates that the plasticizer mixture exhibits superior effectiveness in enhancing the performance of the pullulan film/capsule compared to a single plasticizer. Furthermore, thermogravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy indicate that the plasticizer mixture enhances the compatibility and thermal stability of the pullulan films without altering their chemical composition. Among the different mass ratios examined, a 15:15 ratio of sorbitol to glycerol (S/G) is identified as the most optimal, leading to superior physicochemical properties and meeting the requirements for brittleness and disintegration time set by the Chinese Pharmacopoeia. This study provides significant insights into the effect of the plasticizer mixture on the performance of pullulan soft capsules and offers a promising application formula for future use.

Primary Human Pancreatic Cancer Cells Cultivation in Microfluidic Hydrogel Microcapsules for Drug Evaluation

Chemotherapy is an essential postoperative treatment for pancreatic cancer, while due to the lack of effective drug evaluation platforms, the therapeutic outcomes are hampered by tumor heterogeneity among individuals. Here, a novel microfluidic encapsulated and integrated primary pancreatic cancer cells platform is proposed for biomimetic tumor 3D cultivation and clinical drug evaluation. These primary cells are encapsulated into hydrogel microcapsules of carboxymethyl cellulose cores and alginate shells based on a microfluidic electrospray technique. Benefiting from the good monodispersity, stability, and precise dimensional controllability of the technology, the encapsulated cells can proliferate rapidly and spontaneously form 3D tumor spheroids with highly uniform size and good cell viability. By integrating these encapsulated tumor spheroids into a microfluidic chip with concentration gradient channels and culture chambers, dynamic and high-throughput drug evaluation of different chemotherapy regimens could be realized. It is demonstrated that different patient-derived tumor spheroids show different drug sensitivity on-chip, which is significantly consistent with the clinical follow-up study after the operation. The results demonstrate that the microfluidic encapsulated and integrated tumor spheroids platform has great application potential in clinical drug evaluation.

Removal of anionic and cationic dyes using porous chitosan/carboxymethyl cellulose-PEG hydrogels: Optimization, adsorption kinetics, isotherm and thermodynamics studies

Chitosan (CS)/carboxymethyl cellulose (CMC) porous hydrogels chemically crosslinked by epichlorohydrin were synthesized using polyethylene glycol (PEG) as a pore-forming agent for anionic (Congo red, CR) and cationic (methylene blue, MB) dyes removal from aqueous solutions. The swelling ratio of hydrogels prepared with 2 % CS and 2 % CMC (CS₂/CMC₂) exhibited optimal performance at different pHs. The addition of PEG into hydrogels (denoted as CS₂/CMC₂-PEG_1.25) exhibited a significantly higher adsorption for CR and MB, increasing from 117.83 to 159.12 mg/g and 110.2 to 136 mg/g, respectively. The comprehensive analyses of Fourier transform infrared spectroscopy, thermalgravimetric study and scanning electron microscopy showed that CS₂/CMC₂-PEG_1.25 hydrogels became more porous with no significant changes in intermolecular and intramolecular interactions, compared with CS₂/CMC₂ hydrogels. The adsorption process for CR and MB conformed to the pseudo-second-order and pseudo-first-order kinetics models, respectively. The results of adsorption isotherm for CR followed both Freundlich and Langmuir models with the maximum adsorption capacities of 1053.88 mg/g, whereas the isotherm for MB fitted the Langmuir model better with the maximum adsorption capacities of 331.72 mg/g. The thermodynamic study results proved that the CR and MB adsorption by hydrogels was spontaneous, but the CR adsorption was endothermic and the MB adsorption was exothermic.

Hydrophobization of aerogels based on chitosan, nanocellulose and tannic acid: Improvements on the aerogel features and the adsorption of contaminants in water

Hydrophobic chitosan aerogels are promising adsorbents for immiscible contaminants such as oils and organic solvents. However, few studies have reported the application of hydrophobic aerogels as adsorbent for organic contaminants dissolved in water. Herein, novel highly hydrophobic chitosan (CS) beads containing cellulose nanocrystals (CNC) and hydrophobized tannic acid (HTA) composite were prepared with different CS and CNC-HTA content to achieve an optimized adsorbent to remove emerging contaminants from water in batch and fixed-bed assays. The CS@CNC-HTA beads properties were assessed by FTIR, XRD, SEM, XPS, Micro-CT, WCA, and zeta potential. Supramolecular interactions and physical interlacements between CS and CNC-HTA enabled the formation of CS@CNC-HTA beads with high porosity (98.6%), great volume of open pore space (10.16 mm³) and hydrophobicity (121.8°). The 1:1 CS@CNC-HTA beads showed the best performance for removing the pharmaceutical sildenafil citrate, the basic blue 26 dye, and the surfactant cetylpyridinium chloride, reaching adsorption capacities of 86 (73%), 375 (84%), and 390 (90%) mg.g^-1, respectively. The 1:1 CS@CNC-HTA beads efficiently removed sildenafil citrate, basic blue 26 and cetylpyridinium chloride in fixed-bed experiments with exhaustion times of 890, 300, and 470 min, respectively. Theoretical calculations and adsorption assays indicate that the main attractive interactions are pyridinium-π, π-π, electrostatic and hydrophobic.

Immobilizing of lead and copper using chitosan-assisted enzyme-induced carbonate precipitation

Enzyme-induced carbonate precipitation (EICP) is considered as an environmentally friendly method for immobilizing heavy metals (HMs). The fundamental of the EICP method is to catalyze urea hydrolysis using the urease, discharging CO₃^2- and NH₄⁺. CO₃^2- helps to form carbonates that immobilize HMs afterwards. However, HMs can depress urease activity and reduce the degree of urea hydrolysis. Herein, the potential of applying the chitosan-assisted EICP method to Pb and Cu immobilization was explored. The chitosan addition elevated the degree of urea hydrolysis when subjected to the effect of Cu²⁺ toxicity where the protective effect, flocculation and adsorption, and the formation of precipitation, play parts in improving the Cu immobilization efficiency. The use of chitosan addition, however, also causes the side effect (copper-ammonia complex formation). Two calcium source additions, CaCl₂ and Ca(CH₃COO)₂, intervened in the test tube experiments not only to prevent pH from raising to values where Cu²⁺ complexes with NH₃ but also to separate the urease enzyme and Cu²⁺ from each other with the repulsion of charges. The FTIR spectra indicate that the chitosan addition adsorbs Cu²⁺ through its surface hydroxyl and carboxyl groups, while the SEM images distinguish who the mineral are nucleating with. The findings shed light on the potential of applying the chitosan-assisted EICP method to remedy lead- and copper-rich water bodies.

Stability improvement of carboxymethyl cellulose/chitosan complex beads by thermal treatment

Carboxymethyl cellulose (CMC) and chitosan (CHI) are two well-known natural polymer derivatives, as such the CMC@CHI complex beads fulfill many requirements for bio-related and safety-required applications. However, poor mechanical properties of CMC@CHI beads hinder their applications. We managed to improve the beads stability by a simple thermal treatment during the bead preparation. The effects of temperature, changing from 25 °C to 75 °C, on the stability of the formed beads were investigated. The morphology, diameter, shell thickness and structure of the beads treated at different temperature were analyzed using SEM, XPS and FTIR. The mechanical test and swelling experiments showed that the thermal treatment enhanced the bead's ability to withstand pressure and swelling. The beads treated at 75 °C showed the best pressure resistance, while the beads treated at 55 °C exhibited the highest swelling capability without losing integrity. This method is convenient to implement, not only improves the stability, but also controls the swelling capacity and mechanical properties of the beads, which are important for their potential applications in adsorption and controlled release. More importantly, this work offered insights on the effects of thermal treatment on the complexation process of the two polysaccharide molecular chains.

Cross-Linked Carboxymethylcellulose Adsorbtion Membranes from Ziziphus lotus for the Removal of Organic Dye Pollutants

The goal of this study is to assess Ziziphus lotus's potential for producing carboxymethylcellulose adsorption membranes with the ability to adsorb methyl green from wastewaters by the revalorization of its cellulosic fraction. The cellulose from this feedstock was extracted by an alkaline process and TAPPI standard technique T 203 cm-99 and afterwards they were carboxymethylated. The obtained carboxymethylcelluloses were deeply characterized, being observed that the carboxymethylcellulose produced from the alkaline cellulose presented the higher solubility due to its lower crystallinity degree (53.31 vs. 59.4%) and its higher substitution degree (0.85 vs. 0.74). This carboxymethylcellulose was cross-linked with citric acid in an aqueous treatment in order to form an adsorption membrane. The citric acid provided rigidity to the membrane and although it was hydrophilic it was not soluble in water. By evaluating the potential of the produced membrane for the removal of pollutant dyes from wastewater, it was observed that the adsorption membrane prepared from the carboxymethylcellulose's produced from the Ziziphus lotus was able to remove 99% of the dye, methyl green, present in the wastewater. Thus, this work demonstrates the potential of the Ziziphus lotus for the production of a novel and cost-effective carboxymethylcellulose adsorption membrane with high capacity to treat wastewaters.

Breathability and Moisture Permeability of Cellulose Nanocrystals Hollow Microsphere Coatings for PET Fabrics

In this study, cellulose nanocrystals hollow microspheres (HMs) were fabricated through Pickering emulsion polymerization, in which hydrophobically modified cellulose nanocrystals (CNCs) acted as Pickering stabilizers. The hollow interior core was prepared by solvent evaporation. This manuscript describes the synthesis of HMs in detail. The hollow structure and nanoscale size of HMs were verified using TEM. The resultant HMs could easily coat self-forming films on the surface of PET fabrics. Additionally, these coatings exhibited superior breathability and moisture permeability properties with a high one-way transport index of 936.33% and a desirable overall moisture management capability of 0.72. Cellulose nanocrystal hollow microsphere coatings could be used as a moisture-wicking functionality agent for finishing fabrics, oil-water separation, and fog harvesting.

Efficient and selective adsorption of methylene blue and methyl violet dyes by yellow passion fruit peel

As an important biomass resource, agricultural waste is of great significance to improve the application value. In this study, the yellow passion fruit peel (Y-PFP) was used as a biosorbent to remove cationic dyes (methylene blue (MB) and methyl violet (MV)) by the simple treatment process. And the effects of pH, contact time, initial dye concentration, ionic strength, and temperature on the adsorption performance of Y-PFP were studied. The adsorption process was consistent with the pseudo-second-order kinetic model and Langmuir isotherm. What's more, the maximum adsorption capacity for MB and MV was 324.7 and 485.4 mg·g^-1, respectively. And Y-PFP still exhibited high removal efficiency after five desorption-adsorption cycles. Thus, Y-PFP had highly valuable for the removal of cationic dyes from wastewater with a simple preparation process, low cost, excellent adsorption capacity and selectivity.

Reusable kaolin impregnated aminated chitosan composite beads for efficient removal of Congo red dye: isotherms, kinetics and thermodynamics studies

In this investigation, Kaolin (K) impregnated aminated chitosan (AM-CTS) composite beads were fabricated with multi-features including low-cost, high performance, renewable and ease of separation for adsorption of anionic Congo red (CR) dye. Characterization tools such as FTIR, XRD, SEM, TGA, BET, XPS and Zeta potential were thoroughly employed to confirm the successful formulation process. The results revealed that K@ AM-CTS composite beads displayed higher specific surface area (128.52 m²/g), while the thermal stability was prominently improved compared to pure AM-CTS. In addition, the adsorption equilibrium of CR dye was accomplished rapidly and closely gotten within 45 min. The removal efficiency was significantly enriched and reached 90.7% with increasing kaolin content up to 0.75%, compared to 20.3 and 58% for pristine kaolin and AM-CTS, respectively. Moreover, the adsorption process obeyed the pseudo-first order kinetic model, while data were agreed with the Freundlich isotherm model with a maximum adsorption capacity reached 104 mg/g at pH 6. Furthermore, D–R isotherm model demonstrated the physical adsorption process of CR dye, which includes the electrostatic interactions, ion exchange and H-bonding. Thermodynamics evidenced the spontaneous and endothermic nature of the adsorption process. Interestingly, the developed K@AM-CTS composites beads showed better reusability for eight consecutive cycles, suggesting their feasible applicability for adsorptive removal anionic dyes from polluted aquatic bodies.

Preparation and Drug Release Profile of Chitosan-Siloxane Hybrid Capsules Coated with Hydroxyapatite

Chitosan is a cationic polymer that forms polymerized membranes upon reaction with anionic polymers. Chitosan−carboxymethyl cellulose (CMC) capsules are drug delivery carrier candidates whose mechanical strength and permeability must be controlled to achieve sustained release. In this study, the capsules were prepared from chitosan−γ-glycidoxypropyltrimethoxysilane (GPTMS)−CMC. The mechanical stability of the capsules was improved by crosslinking the chitosan with GPTMS. The capsules were then coated with hydroxyapatite (HAp) by alternately soaking them in calcium chloride solution and disodium hydrogen phosphate solution to prevent rapid initial drug release. Cytochrome C (CC), as a model drug, was introduced into the capsules via two routes, impregnation and injection, and then the CC released from the capsules was examined. HAp was found to be deposited on the internal and external surfaces of the capsules. The amount of CC introduced, and the release rate were reduced by the HAp coating. The injection method was found to result in the greatest CC loading.

Multifunctional Cellulose and Cellulose-Based (Nano) Composite Adsorbents

In recent years, faced with the improvement of environmental quality problems, cellulose and cellulose-based (nano) composites have attracted great attention as adsorbents. In this review article, we first report the recent progress of modification and functionalization of cellulose adsorbents. In addition, the adsorbents produced by the modification and functionalization of carboxymehyl cellulose are also introduced. Moreover, the cellulose-based (nano) composites as adsorbents are reviewed in detail. Finally, the development prospect of cellulose and cellulose-based (nano) composites is studied in the field of the environment. In this review article, a critical comment is given based on our knowledge. It is believed that these biomass adsorbents will play an increasingly important role in the field of the environment.

Quality assessment of lemon (Citrus aurantifolia, swingle) coated with self-healed multilayer films based on chitosan/carboxymethyl cellulose under cold storage conditions

The polyelectrolyte multilayer self-healing coating film of chitosan and carboxymethyl cellulose (PEM-SH) tended to maintain high sensory quality and control physiological and pathological decay of lemon fruits under cold storage. The PEM-SH film was characterized by ATR-IR, XRD, X-ray photoelectron spectroscopy, SEM analysis, swelling ratio, self-healing, and mechanical characteristics. The 3-layered film (3L) exhibited the optimum barrier properties; WVP: 3.32 ± 0.06 g. mm. k Pa-1.h-1.m-2 and GTR: 0.256 ± 0.032 cc.M-2.day-1. The moisture sorption isotherm data were fitted with BET, GAB, and Peleg models and three models showed applicability. The coated fruits exhibit superior features of fruit quality such as reduced weight loss %, respiration rate, and decay symptoms appearance. The 3L-coated fruit showed the lower pectinase enzyme activity (0.689 Ug-1 FW) up to 60 days. As well as, increased total soluble solids, keeping vitamin C of loss and decreasing percentage acidity of juice up to 60 days.

A novel porous hollow carboxyl-polysulfone microsphere for selective removal of cationic dyes

Herein, we obtained porous hollow carboxyl-polysulfone (PH-CPSF) microspheres through non-solvent-induced phase separation (NIPS) method and simple modification, used as highly efficient adsorbents for removing cationic dyes from sewage. The resulting PH-CPSF microspheres possess a hollow core and sponge-like shell structure, with high surface area, durable chemical inertness and structural stability. The as-synthesized PH-CPSF microspheres deliver a desirable adsorption effect after deprotonation treatment, with an adsorption capacity reaching up to 154.5 mg g^-1 at 25 °C (pH = 7) of methylene blue (MB). The inter-molecular interactions between MB and the surface of the PH-CPSF, including π-π interaction, hydrogen bonding, strong charge attraction and weak charge attraction endow the adsorption ability of the PH-CPSF. The pseudo-second-order kinetic model pronounces in the adsorption behavior, and the adsorption equilibrium data is fitted to the Langmuir model. Moreover, PH-CPSF microspheres can also be used as adsorption fillers for large-scale water purification, and a removal rate of 94.0% for MB can be achieved under a flow rate of 8000 L m^-3 h^-1. The reusability of 95.3% removal effect for PH-CPSF microspheres after 20 consecutive cycles can be attained by a simple regeneration treatment. The adsorption efficiency of the PH-CPSF microspheres was evaluated by variety of cationic and anionic dyes, with high adsorption capacity toward cationic dyes (100%) and less than 10% toward anionic dyes. These results manifest that PH-CPSF microspheres are a potential adsorbent with long-term purification capabilities, which are expected to be used in small and large-scale sewage treatment.

Simultaneous adsorption for cationic and anionic dyes using chitosan/electrospun sodium alginate nanofiber composite sponges

The coexistence of anionic and cationic dyes in dye wastewater has highlighted a great necessity to develop amphoteric adsorbents for their simultaneous removal. Herein, an amphoteric composite sponge was successfully fabricated by combining chitosan with electrospun sodium alginate nanofiber using lyophilization in acetic acid/water/dioxane mixed solvents, which owned the abundant functional groups and superior microstructure of interconnected pores and nanoscale fibers, beneficial for the adsorption capacity improvement. The optimum adsorption capacities for Acid Blue-113 and Rhodamine B were 926.2 ± 25.7 mg/g and 695.4 ± 17.0 mg/g, respectively, much higher than that of the controlled sample prepared with chitosan and non-spinning sodium alginate in traditional acetic acid/water solvents. Meanwhile, the sponge provided with the superior adsorption performance under various pH environment and cyclic adsorption. Importantly, it had considerable simultaneous adsorption capacity for binary system containing anionic and cationic dyes. Overall, the chitosan/electrospun sodium alginate nanofiber composite sponge shows potential for complex wastewater treatment.

Magnetic graphene oxide-containing chitosan‑sodium alginate hydrogel beads for highly efficient and sustainable removal of cationic dyes

Developing recyclable and efficient adsorbents for cationic dyes removal from wastewater is crucial for ensuring green ecology and drinking water safety. Herein, we demonstrated a novel magnetic gel bead adsorbent that was synthesized by employing graphene oxide (GO) modified Fe₃O₄ as magnetic nanoparticles doped sodium alginate (SA)/chitosan (CS) gel (SA/GO@Fe₃O₄/CS). The GO@Fe₃O₄ sample was prepared based on GO by the chemical co-precipitation method, which not only reduced the aggregation of Fe₃O₄ but also increases the specific surface area of the composite gel beads. The prepared gel beads were used to adsorb methylene blue (MB), neutral red (NR), and safranine T (ST). The experimental results showed that the adsorption capacity of SA/GO@Fe₃O₄/CS gel beads for MB, NR, and ST reached 21.325 mg/g, 44.654 mg/g and 44.313 mg/g. After five recycles, the removal rates could still reach more than 90% of the original, exhibiting a high recovery rate. Therefore, this paper provides a strategy for the preparation of high efficiency and recyclable cationic dye adsorbents with a large specific surface area.

Recent Advances in Functional Polymer Materials for Energy, Water, and Biomedical Applications: A Review

Academic research regarding polymeric materials has been of great interest. Likewise, polymer industries are considered as the most familiar petrochemical industries. Despite the valuable and continuous advancements in various polymeric material technologies over the last century, many varieties and advances related to the field of polymer science and engineering still promise a great potential for exciting new applications. Research, development, and industrial support have been the key factors behind the great progress in the field of polymer applications. This work provides insight into the recent energy applications of polymers, including energy storage and production. The study of polymeric materials in the field of enhanced oil recovery and water treatment technologies will be presented and evaluated. In addition, in this review, we wish to emphasize the great importance of various functional polymers as effective adsorbents of organic pollutants from industrial wastewater. Furthermore, recent advances in biomedical applications are reviewed and discussed.

A decade development in the application of chitosan-based materials for dye adsorption: A short review

The presence of dyes in the aquatic environment as a result of anthropogenic activities, especially textile industries, is a critical environmental challenge that hinders the availability of potable water. Different wastewater treatment approaches have been used to remediate dyes in aquatic environments; however, most of these approaches are limited by factors ranging from high cost to the incomplete removal of the dyes and contaminants. Thus, the use of adsorption as a water treatment technology to remove dyes and other contaminants has been widely investigated using different adsorbents. This study evaluated the significance of chitosan as a viable adsorbent for removing dyes from water treatment. We summarised the literature and research results obtained between 2009 and 2020 regarding the adsorption of dyes onto chitosan and modified chitosan-based adsorbents prepared through physical and chemical processing, including crosslinking impregnation, grafting, and membrane preparation. Furthermore, we demonstrated the effects of various chitosan-based materials and modifications; they all improve the properties of chitosan by promoting the adsorption of dyes. Hence, the application of chitosan-based materials with various modifications should be considered a cutting-edge approach for the remediation of dyes and other contaminants in aquatic environments toward the global aim of making potable water globally available.

Effect of carbonaceous fillers on adsorption behavior of multifunctional diatomite-based foams for wastewater treatment

Nowadays the study of the potential applications of multifunctional materials for environmental remediation is one of the main goals of the materials engineering. Multifunctional porous materials, MPMs, incorporate, all in once, different and multiple functionalities that make them suitable for several uses and can satisfy many purposes at the same time. Multifunctional diatomite-based foams with a hierarchical porosity, already produced and characterized to be applied in building as well as aerospace sectors, are proposed as adsorbents for inorganic and organic pollutants removal from wastewaters. Then, the effect of the addition of different carbonaceous nanofillers (graphite, graphene and graphene oxide) on the water purification efficiency of the adsorbent was evaluated. Firstly, pristine MPM showed the best performance in adsorbing Indigo Carmine due to its intrinsic chemism and hierarchical porosity (at macro-, micro- and nano-level), but it is not the best with respect to the Cd²⁺ adsorption, if compared with the nanocomposites. Among the nanocomposite products, both graphene- and graphene oxide-MPM samples showed a significantly improved adsorption capacity towards Cd²⁺. This behavior is due to the synergistic effect of the finer morphology, higher available foam surface, and the highly exfoliated fillers, graphene and graphene oxide, which permit a better dispersion into the matrix.

Fabrication of polyethylenimine functionalized magnetic cellulose nanofibers for the sorption of Ni(II), Cu(II) and Cd(II) in single-component and multi-component systems

Novel polyethyleneimine functionalized cellulose nanofiber magnetic composites (PEI-CNFs@Fe₃O₄) were prepared using banana peels as the raw materials for the sorption of Ni(II), Cu(II) and Cd(II) in single-component and multi-component systems. The batch experiments, spectral analyses and model fittings were used to reveal the sorption properties. The sorption of Ni(II), Cu(II) and Cd(II) on PEI-CNFs@Fe₃O₄ all conformed to the Langmuir isotherm and pseudo-second-order kinetic models. And the maximum sorption capacities of PEI-CNFs@Fe₃O₄ towards Ni(II), Cu(II) and Cd(II) were 134.38, 93.71 and 173.56 mg g^-1, respectively. The main sorption mechanism of Ni(II), Cu(II) and Cd(II) on PEI-CNFs@Fe₃O₄ is the strong surface complexation of the amino, carboxyl and hydroxyl groups with Ni(II), Cu(II) and Cd(II) ions. Especially, the introduction of PEI contributed to the improvement in the sorption capacities of PEI-CNFs@Fe₃O₄ towards the heavy metals. Besides, the size of the ionic radius and the strength of the surface complexing ability with PEI-CNFs@Fe₃O₄ are the reasons for the difference in the sorption capacities of Ni(II), Cu(II) and Cd(II) (Cd(II) > Ni(II) > Cu(II)). In conclusion, PEI-CNFs@Fe₃O₄ has shown the advantages of low cost, simple preparation, easy magnetic separation, environmental friendliness and high sorption capacity, thus having a broad application prospect in the treatment of multi-heavy metals polluted water.

Super and Selective Adsorption of Cationic Dyes onto Carboxylate-Modified Passion Fruit Peel Biosorbent

The carboxylate-functionalized passion fruit peel (PFPCS) was an efficient and rapid biosorbent for wastewater treatment. The PFPCS exhibited excellent selectivity to the cationic dyes, where the maximum adsorption capacities for methylene blue (MB) and methyl violet (MV) were 1,775.76 mg g-1 and 3,756.33 mg g-1, respectively. And the adsorption process of MB and MV on PFPCS reached equilibrium within 20 min. Moreover, the adsorption conditions and mechanisms were investigated. The adsorption process was in good agreement with the pseudo-second-order and Langmuir isotherm models. The adsorption mechanism was also proposed to be electrostatic interaction and hydrogen bond. After six cycles of desorption-adsorption, the removal efficient of MB and MV could be kept above 95%. Thus, PFPCS was considered as a highly efficient absorbent for removing cationic dyes from polluted water due to excellent adsorption characteristics, low cost and environmental friendliness.

Chitosan-based hybrid materials for adsorptive removal of dyes and underlying interaction mechanisms

Environmental pollution by dyes molecules has become a subject of intensive research in recent years due to their hazardous effects on human health, organisms, and animals. Effective treatment and removal of dye molecules from the environmental matrices and water sources are of supreme concern. The deployment of cheap, safe, green, sustainable, and eco-friendly materials to remove these pollutants from water is the main challenge during the last decades. Chitosan and its derivatives/composites, as a cheap, easily available, and environmentally friendly sorbent, have attracted increasing attention for the removal of dye molecules. This review article focuses on the application of chitosan and chitosan-based smart adsorbents for the removal of dyes. Recent methods for the preparation of chitosan-based composites and their application in the removal of dyes are discussed. Moreover, the possible mechanisms for the interaction of chitosan and chitosan-based adsorbents with dyes molecules were evaluated. Finally, future prospects of using chitosan as an adsorbent for the removal of dye molecules are directed.

Adsorption-photocatalysis performance of polyaniline/dicarboxyl acid cellulose@graphene oxide for dye removal

A novel 3-D biopolymer-based adsorption-photocatalytic composite, polyaniline/dicarboxyl acid cellulose@graphene oxide was synthesized and was employed to remove the reactive brilliant red K-2G from aqueous solution. The addition of dicarboxyl acid cellulose could improve the morphology, structure, stability and dispersity of the nanocomposite, thus providing excellent adsorption and photocatalysis performance to the product. Batch of experiments were conducted in two scenarios: adsorption followed by photocatalysis process and simultaneous adsorption-photocatalysis process. For the first scenario, adsorption equilibrium can be reached within 25 min, the expected adsorption capacity was 447.0 mg·g^-1; the subsequent photocatalysis process was carried out under light irradiation and the removal capacity could further improve to 729.0 mg·g^-1 under equilibrium state (about 180 min). For the simultaneous adsorption-photocatalytic process, the removal capacity was about 558.1 mg·g^-1 at about 25 min and the total removal capacity could reach to 733.3 mg·g^-1 under equilibrium state. PANI-DCC@GO exhibited excellent reusability and had potential in the treatment of dyes polluted wastewater.

Preparation, characterization, and antibacterial property of carboxymethyl cellulose derivatives bearing tetrabutylammonium salt

Carboxymethyl cellulose derivatives bearing tetrabutylammonium moieties (CMC-TBA) were synthesized by the acidification of carboxymethyl cellulose (CMC) followed by acid-base neutralization with tetrabutylammonium hydroxide. The products were identified by Fourier transform infrared (FT-IR), ¹H nuclear magnetic resonance (NMR) spectroscopy and the degrees of substitution (DS) values were also quantified according to the integral area values in ¹H NMR spectra. It was revealed that DS values had a positive relationship with the molar ratios of TBAOH to CMC. The antibacterial behaviors against gram-positive bacteria S. aureus and gram-negative bacteria E. coli were investigated using serial two-fold dilution method (MIC and MBC) and the disc diffusion method (inhibition zone). The results showed that comparison with CMC, all new CMC-TBA derivatives exhibited high antibacterial activity that depends on bacteria type and their degrees of cationization. The antibacterial action was more effective against S. aureus than E. coli, which could be attributed to the fact that the latter has a complicated bilayer structure of cell wall. Besides, an apparent tendency that the antibacterial activity of CMC-TBA derivatives enhanced with an increase in the degrees of cationization was found. This work suggests that these new derivatives can be introduced as efficient antibacterial biomaterials for biomedical purposes.

Preparation of fibrous chitosan/sodium alginate composite foams for the adsorption of cationic and anionic dyes

Natural polysaccharide is attractive for preparing the environmentally friendly and highly efficient adsorbent. However, to obtain an efficient amphoteric absorbent for dealing with complex wastewater is still challenging. Herein, fibrous chitosan/sodium alginate composite foams were prepared by lyophilization with ternary acetic acid/water/tetrahydrofuran solvents, which had suitable morphology of interconnected pores and microscale fibers for dye adsorption. The amphoteric composite foams showed high adsorption capacities for both anionic Acid Black-172 (817.0 mg/g) and cationic Methylene Blue (1488.1 mg/g), which were far superior to those of the control samples prepared with traditional solvents of acetic acid/water. The adsorption kinetics and isotherm data showed that the adsorption followed the pseudo-second-order and Langmuir model. Further thermodynamics analysis revealed the adsorption was a spontaneous process. Meanwhile, the foams achieved effective adsorption capacity of AB-172 and MB dyes under a wide range of environmental pH, and maintained high adsorption efficiency even after four cycles. The adsorption mechanism is chemisorption, where the adsorption capacities for the anionic and cationic dyes were dependent on the mass ratio of chitosan to sodium alginate. As a novel amphoteric adsorbent, the fibrous chitosan/sodium alginate composite foam shows the potential to remove both cationic and anionic dyes from wastewaters.

Selective removal of anionic and cationic dyes by magnetic Fe3O4-loaded amine-modified hydrochar

Fe₃O₄-loaded protonated amine-modified hydrochar (Fe₃O₄-PAMH) was successfully prepared and characterized by scan electron microscopy equipped with energy-dispersion X-ray spectroscopy, zeta potential analysis, vibration sample magnetometry, Fourier transform infrared and X-ray photoelectron spectroscopies, Brunauer-Emmett-Teller measurement, and X-ray diffraction. Adsorption properties of Fe₃O₄-PAMH to negatively-charged methyl orange (MO) or positively-charged methylene blue (MB) in one- or two-component systems were evaluated. The Fe₃O₄-PAMH selectively adsorbed MO and MB at pH 5 and 11, respectively. The maximum MO and MB uptake capacities of Fe₃O₄-AMHC were 202.02 mg/g (pH 5.0) and 148.84 mg/g (pH 11) respectively. The Fe₃O₄-PAMH can be reused with simple pH management in adsorption-desorption cycles. The MB and MO adsorption abilities on Fe₃O₄-PAMH were maintained above 99% and 75% for five consecutive recycles, respectively. Thus, Fe₃O₄-PAMH shows powerful potential in efficiently and selectively adsorbing anionic or cationic dyes from mixed wastewater.

Preparation and Self-Repairing Properties of MF-Coated Shellac Water-Based Microcapsules

A self-repairing microcapsule was prepared by emulsion polymerization using melamine formaldehyde resin (MF) as wall material, and a mixture of shellac solution and water-based coating as core material. The orthogonal experiment was carried out through five factors and four levels. The effects of Wcore:Wwall, Wemulsifier:Wcore, stirring rate, Wshellac:Wcoating, Wemulsifier solution:Wcore on the output and coverage rate of microcapsules were studied. The stirring rate has a great influence on the preparation process of the MF-coated shellac water-based microcapsules. When the Wcore:Wwall is 0.8:1, Wemulsifier:Wcore is 3:100, stirring rate is 600 rpm, Wshellac:Wcoating is 1:1, Wemulsifier solution:Wcore is 9:1, the prepared microcapsules have the best shape and size. With the increase in concentration of microcapsules, the color difference and gloss of paint film decreased gradually. The tensile strength, scanning electron microscopy (SEM), infrared spectroscopy and repair effects of the paint film were analyzed. When the concentration of microcapsules was 5.0–10.0%, the comprehensive performance of the paint film was better, providing a technical reference for the self-repairing coatings.