Metal-organic frameworks for highly efficient heterogeneous Fenton-like catalysis

Preparation of ZnIn2S4/MoS2-SA Photocatalyst Gel for Wastewater Treatment: Photocatalytic Performance and Solar Interfacial Evaporation

With the rapid advancement of industrialization, wastewater pollution has become an increasingly severe environmental issue. The integration of photocatalysis with solar interfacial evaporation technology, which leverages the abundant and clean energy of solar power, has drawn growing attention as effective solutions to this problem. In this study, MoS2 nanosheets with low-dimensional and controllable morphology were successfully grown on layered ZnIn2S4 using a simple template method, resulting in a novel nanoflower heterojunction photocatalyst. This photocatalyst was then combined with sodium alginate, and aerogels were fabricated through directional freezing technology. The ZnIn2S4/MoS2 photocatalytic aerogel demonstrated excellent photocatalytic performance under visible light, efficiently degrading various pollutants such as rhodamine B(RhB)(30 min, 99%), methyl orange(MO)(30 min, 99%), tetracycline(TC)(1h, 88%), and other antibiotics and dyes. Notably, the degradation efficiency for tetracycline remained at 88% even after five cycles of use, highlighting the aerogel's strong reusability and stability across different pollutants. Additionally, the current aerogel composite exhibits an evaporation rate of up to 1.984 kg m-2 h-1 and a photothermal conversion efficiency of 95.5%. These results demonstrate that the ZnIn2S4/MoS2 photocatalytic aerogel is a promising candidate for sustainable water treatment, with broad applicability and stable photocatalytic degradation efficiency and interfacial evaporation efficiency under different polluted environments.

ZIF-Derived Catalyst with Co-Co/Co-N Dual Active Sites for Boosting Mixed Pathway Decontamination in Fenton-like Catalysis

Pollutant degradation via radical-nonradical mixed pathways offers opportunities to break the reactivity-stability trade-off in heterogeneous Fenton-like catalysis for water treatment; however, a precise catalyst design to enforce such mixed pathways remains challenging. Herein, by using bimetallic ZIFs as the precursor, we fabricated a cobalt (Co)-based catalyst (Co0.75Zn0.25-NC) with dual active sites for peroxymonosulfate (PMS) activation, where the Co-Co site and Co-N site preferentially catalyze the sulfate radicals and single oxygen generation, respectively. The system exhibited superior pollutant degradation activity, especially for the lectron-rich pollutants like tetracycline, high PMS utilization efficiency, negligible interference by the complicated water matrix, and good adaptation to broad pH and water quality conditions. A stable operation of the corresponding catalytic ceramic membrane was also demonstrated, achieving ∼70% pollutant removal during the long-term continuous-flow operation. This work offers valuable references to guide the Fenton-like catalyst design toward sustainable and low-carbon water purification applications.

Engineering a multivariate cobalt metal-organic framework for high photocatalytic activity: the impact of mixed ligands and metal incorporation in a visible light-driven heterogeneous photo-Fenton reaction for water treatment

Metal-organic frameworks (MOFs) have attracted increasing attention for the removal of organic pollutants in wastewater via photocatalysis. Here, we design a multivariate modification of ZIF-9 to tune its electronic properties for use in visible light photocatalysis. A controllable synthesis of ZIF-9 and its multivariate forms with the incorporation of copper and the 2-imidazolecarboxaldehyde (ica) ligand was carried out. The materials are tested for the removal of the model dye methylene blue (MB) by a heterogeneous photo-Fenton-like reaction at neutral pH and room temperature. Cu-ZIF-9-ica (UPO-3) shows high photocatalytic activity under both visible and ultraviolet A (UVA) light, achieving 94% MB degradation in 45 min, compared to 65% MB degradation in 120 min using bare ZIF-9. The study revealed a first-order rate constant of 0.0475 min-1 for Cu-ZIF-9-ica compared to 0.0088 min-1 for ZIF-9 under visible light. The improvement of the catalyst was clearly attributed to the co-incorporation of Cu and the ica ligand in the MOF, which reduces the band gap, in agreement with DFT calculations. Reproducibility and recyclability tests proved that Cu-ZIF-9-ica can be used for at least 3 cycles without a significant loss of efficiency, making it a promising material for the study and application of wastewater treatment.

Heterogeneous Fenton degradation of ciprofloxacin by RM-Co PBA prepared with red mud as iron source and carrier

Loading catalysts onto carriers to prepare supported catalysts is an important strategy for improving dispersion, stability and catalytic performance. In this study, we synthesized a supported red mud (RM)-based Fe-Co Prussian blue analogue (RM-Co PBA) catalyst using RM as iron source and carrier by acid dissolution-reduction-coprecipitation method to activate H2O2 for the degradation of ciprofloxacin (CIP). The RM-Co PBA obtained under the synthesis conditions of HCl concentration of 2.4 M and potassium cobalt cyanide addition of 4 mM exhibited the best dispersibility and regular shape, resulting in high catalytic performance. The degradation efficiency of RM-Co PBA/H2O2 system reached 75.79% in 10 min, which was 10.54 times and 1.21 times of that of RM/H2O2 system and Fe-Co PBA/H2O2 system, respectively. The RM-Co PBA/H2O2 system was almost unaffected by pH and was suitable for treating low concentration CIP wastewater. Additionally, the system can be reused well and possessed certain resistance to inorganic anions. The results showed that superoxide radical (⋅O2-) was the main ROS attacking CIP, which accumulated continuously in the cycling process of Co(III)/Fe(III) and Co(II)/Fe(II). On the other hand, the presence of a large number of oxygen vacancies in RM-Co PBA enhanced the production of ⋅O2- by endowing it with good electron transfer performance. Finally, we proposed possible CIP degradation pathways and demonstrated the toxicity reduction of each pathway by a quantitative structure-activity relationship analysis. This study provides guidance for the resource utilization of RM and the efficient treatment of antibiotic wastewater.

rGO/MUT-15 nanocomposite as a Fenton-like photocatalyst for the degradation of Acid Yellow 73 under visible light

The Fenton-like reaction is an advanced oxidation process (AOP) used to effectively eliminate organic pollutants. Fenton-like materials include metal-organic frameworks (MOFs) containing Fe, Co, Mn, and Cu metal ions. MOF-based photocatalysts with the highest performance can be designed and synthesized using these metal ions. A new Mn-based metal-organic framework with the formula of [Mn2(DClTPA)2(DMF)3] (MUT-15) containing 2,5-dichloroterephthalic acid (DClTPA) and N,N-dimethylformamide (DMF) was prepared via a solvothermal method. According to single-crystal X-ray analysis, MUT-15 (MUT = Materials from University of Tehran) has a tetragonal crystal system with the I41/a space group. A simple one-pot solvothermal method was used to prepare a rGO/MUT-15 nanocomposite. PXRD, FT-IR, TGA, FE-SEM, TEM, EDX, DRS, PL, EIS, and Mott-Schottky measurements were used to characterize the MUT-15 and rGO/MUT-15 nanocomposite. Under visible-light irradiation, MUT-15 and rGO/MUT-15 as Fenton-like photocatalysts degraded Acid Yellow 73 in only 10 min with outstanding photocatalytic activity rates of 92.39% and 96.10%, respectively. Thus, the Mn(II)-O clusters in MUT-15 significantly contributed to the degradation of Acid Yellow 73 through their Fenton-like effect.

Significant effects of negligible amount of H2O2 on photocatalytic efficiency of MIL-125 and NH2-MIL-125 nanostructures in degradation of methylene blue

The notable impact of a trace amount of hydrogen peroxide (H2O2) on the photocatalytic performance of Ti-based metal-organic frameworks (MOFs), namely MIL-125 and NH2-MIL-125, in the purification of water polluted with chemical agents was studied experimentally. MIL-125 and NH2-MIL-125 were synthesized using the solvothermal method and were characterized by a variety of diagnostic methods. NH2-MIL-125 exhibited a bandgap of 2.8 eV compared to 3.65 eV for MIL-125 with optimal visible light capture capability, indicating the outstanding photodegradation activity of the synthesized MOFs. In addition, the photocatalytic performance of MIL-125 and NH2-MIL-125 was tested for the degradation of methylene blue (MB) as a chemical pollutant in water under both dark conditions and irradiation by visible light and a UVC lamp. NH2-MIL-125 exhibited a significantly higher photodegradation rate compared to MIL-125 due to the presence of the amino group, higher surface electronegativity and slightly lower bandgap. Furthermore, the effect of H2O2 as an electron acceptor on the efficiency of MB degradation was investigated, which markedly enhanced the photocatalytic MB degradation performance due to the ligand-to-metal charge transfer mechanism, particularly for NH2-MIL-125, under all tested conditions.

Mechanistic study of visible light driven photocatalytic degradation of clofibric acid using Fe-based metal organic frameworks (MOFs)

Although a series of past studies proved the potential usage of Fe-based metal-organic frameworks (MOFs) as photocatalysts, there remains a knowledge gap of the photocatalytic mechanism stemming from the challenge to separate the simultaneous sorption and photocatalytic degradation. Thus, this article aimed to suggest a novel approach by desorbing target molecules during photocatalysis to excavate the underlying mechanisms of sorption and photocatalytic degradation. In this study, two Fe-based MOFs, MIL-101(Fe) and MIL-101(Fe)-NH2, were selected to remove clofibric acid under visible light irradiation. Prior to photocatalysis, sorption mechanism was uncovered based on the sorption kinetic, isotherm, thermodynamic interpretation, and of its dependence on solution pH. The results inferred that the primary sorption mechanism was through the π-π interaction between the benzene ring of clofibric acid and the organic ligand of Fe-based MOFs. Based on these results, photocatalytic mechanism could be independently or jointly assessed during the photocatalytic degradation of clofibric acid. Subsequently, the application of the Tauc method and XPS spectra revealed that the bandgap structure of Fe-based MOFs had the potential to oxidize clofibric acid by producing ROS through the electron excitation upon visible-light illumination. On top of that, the amine functionalization of Fe-based MOF altered the structural moiety that led to an additional strong acid-base interaction with clofibric acid but a decrease in the bandgap limiting the ROS production during photocatalytic activity.

The Z-Scheme MIL-88B(Fe)/BiOBr Heterojunction Promotes Fe(III)/Fe(II) Cycling and Photocatalytic-Fenton-Like Synergistically Enhances the Degradation of Ciprofloxacin

The Z-scheme MIL-88B/BiOBr (referred to as MxBy, whereas x and y are the mass of MIL-88B(Fe) and BiOBr) heterojunction photocatalysts are successfully prepared by a facile ball milling method. By adding low concentration H2O2 under visible light irradiation, the Z-scheme heterojunction and photocatalytic-Fenton-like reaction synergistically enhance the degradation and mineralization of ciprofloxacin (CIP). Among them, M50B150 showed efficient photodegradation efficiency and excellent cycling stability, with 94.6% removal of CIP (10 mg L-1) by M50B150 (0.2 g L-1) under 90 min of visible light. In the MxBy heterojunctions, the rapid transfer of photo-generated electrons not only directly decomposed H2O2 to generate ·OH, but also improved the cycle of Fe3+/Fe2+ pairs, which facilitated the reaction with H2O2 to generate ·OH and ·O2 - radicals. In addition, the effects of photocatalyst dosages, pH of CIP solution, and coexisting substances on CIP removal are systematically investigated. It is found that the photocatalytic- Fenton-like reaction can be carried out at a pH close to neutral conditions. Finally, the charge transfer mechanism of the Z-scheme is verified by electron spin resonance (ESR) signals. The ecotoxicity of CIP degradation products is estimated by the T.E.S.T tool, indicating that the constructed photocatalysis-Fenton-like system is a green wastewater treatment technology.

Size-Dependent Catalysis in Fenton-like Chemistry: From Nanoparticles to Single Atoms

State-of-the-art Fenton-like reactions are crucial in advanced oxidation processes (AOPs) for water purification. This review explores the latest advancements in heterogeneous metal-based catalysts within AOPs, covering nanoparticles (NPs), single-atom catalysts (SACs), and ultra-small atom clusters. A distinct connection between the physical properties of these catalysts, such as size, degree of unsaturation, electronic structure, and oxidation state, and their impacts on catalytic behavior and efficacy in Fenton-like reactions. In-depth comparative analysis of metal NPs and SACs is conducted focusing on how particle size variations and metal-support interactions affect oxidation species and pathways. The review highlights the cutting-edge characterization techniques and theoretical calculations, indispensable for deciphering the complex electronic and structural characteristics of active sites in downsized metal particles. Additionally, the review underscores innovative strategies for immobilizing these catalysts onto membrane surfaces, offering a solution to the inherent challenges of powdered catalysts. Recent advances in pilot-scale or engineering applications of Fenton-like-based devices are also summarized for the first time. The paper concludes by charting new research directions, emphasizing advanced catalyst design, precise identification of reactive oxygen species, and in-depth mechanistic studies. These efforts aim to enhance the application potential of nanotechnology-based AOPs in real-world wastewater treatment.

The use of bimetallic metal-organic frameworks as restoration materials for pollutants removal from water environment

Bimetallic metal-organic frameworks (BMOFs) are a class of functional porous materials constructed by coordination between nodes containing two different metal ions and organic ligands. Studies have shown that the catalytic activity of BMOFs is greatly improved owing to the adjustment of charge distribution and the increase of active sites as well as the synergistic effect between the bimetals, and the advantages of their large specific surface area, high porosity, unique structure and dispersed active centres make them available as important organic materials applied in the field of wastewater treatment. In this review, the preparation and construction methods for BMOFs in recent years are summarized, and we focus on their removal of different types of pollutants in the aqueous environment, including ions, dyes, pharmaceuticals or personal care products, phenolic compounds and microorganisms, as well as their corresponding removal mechanisms. In addition, we provide an outlook on their future opportunities and challenges in wastewater treatment.

Magnetic FNS/MILs nanofibers for highly efficient removal of norfloxacin via adsorption and Fenton-like reaction

Iron-containing MOFs have attracted extensive interest as promising Fenton-like catalysts. In this work, magnetic Fe3O4 nanofiber (FNS)/MOFs composites with stable structure, included FNS/MIL-88B, FNS/MIL-88A and FNS/MIL-100, were prepared via the in-situ solvothermal method. The surface of the obtained fibers was covered by a dense and continuous MOFs layer, which could effectively solve the agglomeration problem of MOFs powder and improved the catalytic performance. The adsorption and catalytic properties of FNS/MOFs composites were evaluated by removal of norfloxacin. FNS/MIL-88B showed the best performance with a maximum adsorption capacity up to 214.09 mg/g, and could degrade 99% of NRF in 60 min. Meanwhile, FNS/MIL-88B had a saturation magnetization of 20 emu/g, and could be rapidly separated by an applied magnetic field. The self-supported nanofibers allowed the adequate contact between MOFs and pollutants, and promoted the catalytic activity and high stability. We believe that this work provided a new idea for the design and preparation of Fenton-like catalysts especially MOFs composites.

Photocatalytic systems: reactions, mechanism, and applications

The photocatalytic field revolves around the utilization of photon energy to initiate various chemical reactions using non-adsorbing substrates, through processes such as single electron transfer, energy transfer, or atom transfer. The efficiency of this field depends on the capacity of a light-absorbing metal complex, organic molecule, or substance (commonly referred to as photocatalysts or PCs) to execute these processes. Photoredox techniques utilize photocatalysts, which possess the essential characteristic of functioning as both an oxidizing and a reducing agent upon activation. In addition, it is commonly observed that photocatalysts exhibit optimal performance when irradiated with low-energy light sources, while still retaining their catalytic activity under ambient temperatures. The implementation of photoredox catalysis has resuscitated an array of synthesis realms, including but not limited to radical chemistry and photochemistry, ultimately affording prospects for the development of the reactions. Also, photoredox catalysis is utilized to resolve numerous challenges encountered in medicinal chemistry, as well as natural product synthesis. Moreover, its applications extend across diverse domains encompassing organic chemistry and catalysis. The significance of photoredox catalysts is rooted in their utilization across various fields, including biomedicine, environmental pollution management, and water purification. Of course, recently, research has evaluated photocatalysts in terms of cost, recyclability, and pollution of some photocatalysts and dyes from an environmental point of view. According to these new studies, there is a need for critical studies and reviews on photocatalysts and photocatalytic processes to provide a solution to reduce these limitations. As a future perspective for research on photocatalysts, it is necessary to put the goals of researchers on studies to overcome the limitations of the application and efficiency of photocatalysts to promote their use on a large scale for the development of industrial activities. Given the significant implications of the subject matter, this review seeks to delve into the fundamental tenets of the photocatalyst domain and its associated practical use cases. This review endeavors to demonstrate the prospective of a powerful tool known as photochemical catalysis and elucidate its underlying tenets. Additionally, another goal of this review is to expound upon the various applications of photocatalysts.

Cobalt-based hybrid nanoparticles loaded with curcumin for ligand-enhanced synergistic nanocatalytic therapy/chemotherapy combined with calcium overload

The therapeutic efficacy of Fenton or Fenton-like nanocatalysts is usually restricted by the inappropriate pH value and limited concentration of hydrogen peroxide (H2O2) at the tumor site. Herein, calcium carbonate (CaCO3)-mineralized cobalt silicate hydroxide hollow nanocatalysts (CSO@CaCO3, CC) were synthesized and loaded with curcumin (CCC). This hybrid system can simultaneously realize nanocatalytic therapy, chemotherapy and calcium overload. With the stabilization of liposomes, CCC is able to reach the tumor site smoothly. The CaCO3 shell first degrades in an acidic tumor environment, releasing Cur and Ca2+, and the pH value of the tumor is increased simultaneously. Then the exposed CSO catalyzes the Fenton-like reaction to convert H2O2 into ˙OH and enhances the cytotoxicity of curcumin (Cur) by catalytically oxidizing it to a ˙Cur radical. Curcumin not only induces the chemotherapy effect but also serves as a nucleophilic ligand and an electron donor in the catalytic system, enhancing the Fenton-like activity of CCC by electron transfer. In addition, calcium overload also amplifies the efficacy of ROS-based therapy. In vitro and in vivo results show that CCC exhibited an excellent synergistic tumor inhibition effect without any clear side effect. This work proposes a novel concept of nanocatalytic therapy/chemotherapy synergistic mechanism by the ligand-induced enhancement of Fenton-like catalytic activity, and inspires the construction of combined therapeutic nanoplatforms and multifunctional nanocarriers for drug and ion delivery in the future.

Fe/Au galvanic nanocells to generate self-sustained Fenton reactions without additives at neutral pH

The generation of reactive oxygen species (ROS) via the Fenton reaction has received significant attention for widespread applications. This reaction can be triggered by zero-valent metal nanoparticles by converting externally added H2O2 into hydroxyl radicals (˙OH) in acidic media. To avoid the addition of external additives or energy supply, developing self-sustained catalytic systems enabling onsite production of H2O2 at a neutral pH is crucial. Here, we present novel galvanic nanocells (GNCs) based on metallic Fe/Au bilayers on arrays of nanoporous silica nanostructures for the generation of self-sustained Fenton reactions. These GNCs exploit the large electrochemical potential difference between the Fe and Au layers to enable direct H2O2 production and efficient release of Fe2+ in water at neutral pH, thereby triggering the Fenton reaction. Additionally, the GNCs promote Fe2+/Fe3+ circulation and minimize side reactions that passivate the iron surface to enhance their reactivity. The capability to directly trigger the Fenton reaction in water at pH 7 is demonstrated by the fast degradation and mineralization of organic pollutants, by using tiny amounts of catalyst. The self-generated H2O2 and its transformation into ˙OH in a neutral environment provide a promising route not only in environmental remediation but also to produce therapeutic ROS and address the limitations of Fenton catalytic nanostructures.

The correlation between electron exchange capacity of Fenton-like heterogeneous catalyst and catalytic activity

Electron transfer played key role in peroxymonosulfate (PMS) activation for heterogeneous Fenton-like catalysts (HFCs). However, the relationship between electron exchange capacity (EEC) and catalytic activity of HFCs has not been elucidated. Herein, thirteen HFCs reported in our previous studies were selected to measure their EEC via electrochemical methods and to investigate the correlation between EEC and catalytic activity for PMS. The results show that nitrogen-doped graphene oxide had much higher EEC (5.299 mM(e) g-1), followed by reduced graphene oxide (3.23 mM(e) g-1), nitrogen-doped biochar-700 (2.032 mM(e) g-1), graphene oxdie (1.789 mM(e) g-1), nitrogen-doped biochar-300 (1.15 mM(e) g-1), g-C3N4 (0.752 mM(e) g-1) and biochar (0.351 mM(e) g-1). For carbon materials, their catalytic activity was not determined by electron donor capacity (EDC), electron acceptor capacity (EAC) and EEC (EDC + EAC), but was linear correlation with |EDC-EAC| that can characterize the extent of HFCs reacting with PMS. The higher the |EDC-EAC| is, the higher the catalytic activity of HFCs is. For carbonaceous materials, their catalytic activity was not proportional to EAC, but had good linear correlation with EDC and |EDC-EAC|. The discrepancy between carbon materials and carbonaceous materials could be due to the different activation mechanisms. Further analysis found that there was no correlation between EEC and the reactive species derived from PMS, indicating that the produced reactive species was not only controlled by EEC. This study firstly elucidated the correlation between EEC and catalytic activity of HFCs, and |EDC-EAC| could be used as an index for evaluating the catalytic activity of HFCs.

NH2-MIL-101(Fe)-mediated photo-Fenton reaction enhanced simultaneous removal of nitrogen and refractory organics in anammox process through interfacial electron transfer

In this study, H2O2 (0.1 ‰) and NH2-MIL-101(Fe)-driven (150 mg/L) photo-Fenton-coupled anammox were proposed to simultaneously improve the removal efficiency of nitrogen and humic acid. Long-term experiments showed that the total nitrogen removal efficiency was increased by the photo-Fenton reaction to 91.9 ± 1.5 % by altering the bioavailability of refractory organics. Correspondingly, the total organic carbon removal efficiency was significantly increased. Microbial community analyses indicated that Candidatus_Brocadia maintained high activity during photo-Fenton reaction and was the most abundant genus in the reactor. Dissimilatory nitrate reduction to ammonium process and denitrification process were enhanced, resulting in reduced NO3--N production. The establishment of electron transfer between microorganisms and NH2-MIL-101 (Fe) improved the charge separation efficiency of the quantum dots and increased the intracellular adenosine triphosphate content of anammox bacteria. These results indicated that photo-Fenton-anammox process promoted the removal of nitrogen and refractory organics in one reactor which had good economic value and application prospects.

Ratiometric electrochemical determination of hydroxyl radical based on graphite paper modified with metal-organic frameworks and impregnated with salicylic acid

Hydroxyl radical (•OH) detection is pivotal in medicine, biochemistry and environmental chemistry. Yet, electrochemical method-specific detection is challenging because of hydroxyl radicals' high reactivity and short half-life. In this study, we aimed to modify the electrode surface with a specific recognition probe for •OH. To achieve this, we conducted a one-step hydrothermal process to fabricate a CoZnMOF bimetallic organic framework directly onto conductive graphite paper (Gp). Subsequently, we introduced salicylic acid (SA) and methylene blue (MB), which easily penetrated the pores of CoZnMOF. By selectively capturing •OH by SA and leveraging the electrochemical signal generated by the reaction product, we successfully developed an electrochemical sensor Gp/CoZnMOF/SA + MB. The prepared sensor exhibited a good linear relationship with •OH concentrations ranging from 1.25 to 1200 nM, with a detection limit of 0.2 nM. Additionally, the sensor demonstrated excellent reproducibility and accuracy due to the incorporation of an internal reference. It exhibited remarkable selectivity for •OH detection, unaffected by other electrochemically active substances. The establishment of this sensor provides a way to construct MOF-modified sensors for the selective detection of other reactive oxygen species (ROS), offering a valuable experimental basis for ROS-related disease research and environmental safety investigations.

Degradation of norfloxacin by red mud-based prussian blue activating H2O2: A strategy for treating waste with waste

The massive accumulation of red mud (RM) and the abuse of antibiotics pose a threat to environment safety and human health. In this study, we synthesized RM-based Prussian blue (RM-PB) by acid solution-coprecipitation method to activate H2O2 to degrade norfloxacin, which reached about 90% degradation efficiency at pH 5 within 60 min and maintained excellent catalytic performance over a wide pH range (3-11). Due to better dispersion and unique pore properties, RM-PB exposed more active sites, thus the RM-PB/H2O2 system produced more reactive oxygen species. As a result, the removal rate of norfloxacin by RM-PB/H2O2 system was 8.58 times and 2.62 times of that by RM/H2O2 system and PB/H2O2 system, respectively. The reactive oxygen species (ROS) produced in the degradation process included ·OH, ·O2- and 1O2, with 1O2 playing a dominant role. The formation and transformation of these ROS was accompanied by the Fe(III)/Fe(II) cycle, which was conducive for the sustained production of ROS. The RM-PB/H2O2 system maintained a higher degradation efficiency after five cycles, and the material exhibited strong stability, with a low iron leaching concentration. Further research showed the degradation process was less affected by Cl-, SO42-, NO3-, and humic acids, but was inhibited by HCO3- and HPO42-. In addition, we also proposed the possible degradation pathway of norfloxacin. This work is expected to improve the resource utilization rate of RM and achieve treating waste with waste.

Magnetic-acoustic actuated spinous microrobot for enhanced degradation of organic pollutants

A growing interest in the development of efficient strategies for the removal of organic pollutants from polluted water is emerging. As such, artificial micro/nano machines performing excellent water purification tasks have recently attracted more research attention of scientists. Hereby a spinous Fe3O4@PPy microrobot is presented that towards an efficient organic pollutant removal by enhancing Fenton-like reaction. The microrobot is fabricated by wrapping polypyrrole (PPy) on a spiny magnetic template prepared from sunflowers pollen. Modulating the sound pressure and frequency of the ultrasonic field enables the Fe3O4@PPy microrobot to present multimode motion, such as violent eruption-like motion caused by local cavitation (ELM), march-like unific motion (MLM), and typhoon-like rotation toward the center gathered motion (TLM). This multimode motion achieves the sufficient locomotion of microrobots in three-dimensional space and effective contact with organic pollutants in polluted water. Furthermore, a 5.2-fold increase in the degradation rate of methylene blue has been realized using Fe3O4@PPy microrobots under low-concentration hydrogen peroxide conditions. Also, the magnetically controlled recovery of microrobots from water after the completion of the degradation task has been demonstrated. The magnetic-acoustic actuated spinous microrobot can be extrapolated to other catalytic microrobot, developing a new strategy for an easier implementation and recovery of microrobot in real applications of water purification.

New Insights on Designing the Next-Generation Materials for Electrochemical Synthesis of Reactive Oxidative Species Towards Efficient and Scalable Water Treatment: A Review and Perspectives

Electrochemical water remediation technologies offer several advantages and flexibility for water treatment and degradation of contaminants. These technologies generate reactive oxidative species (ROS) that degrade pollutants. For the implementation of these technologies at an industrial scale, efficient, scalable, and cost-effective in-situ ROS synthesis is necessary to degrade complex pollutant mixtures, treat large amount of contaminated water, and clean water in a reasonable amount of time and cost. These targets are directly dependent on the materials used to generate the ROS, such as electrodes and catalysts. Here, we review the key design aspects of electrocatalytic materials for efficient in-situ ROS generation. We present a mechanistic understanding of ROS generation, including their reaction pathways, and integrate this with the key design considerations of the materials and the overall electrochemical reactor/cell. This involves tunning the interfacial interactions between the electrolyte and electrode which can enhance the ROS generation rate up to ~ 40% as discussed in this review. We also summarized the current and emerging materials for water remediation cells and created a structured dataset of about 500 electrodes and 130 catalysts used for ROS generation and water treatment. A perspective on accelerating the discovery and designing of the next generation electrocatalytic materials is discussed through the application of integrated experimental and computational workflows. Overall, this article provides a comprehensive review and perspectives on designing and discovering materials for ROS synthesis, which are critical not only for successful implementation of electrochemical water remediation technologies but also for other electrochemical applications.

Terrace-Like 2D Hierarchically Porous Iron/Cobalt Metal-Organic Framework: Ambient Fast Synthesis and Efficient Oxygen Evolution Reaction Application

It is urgent to design a low-cost electrocatalyst with high activity to enhance the efficiency of oxygen evolution reaction (OER), which is limited by the slow four-electron transfer kinetics process. Nevertheless, traditional synthetic methods, including calcination and solvothermal, of the electrocatalysts are high-cost, low-yield, and energy-hogging, which limits their industrial application. Herein, an ambient fast synthetic method is developed to prepare terrace-like Fe/Co bimetal-organic framework (TFC-MOF) electrocatalyst materials in gram scale in 1 h. The method in this paper is designable based on coordination chemistry. Fe and Co ions can coordinate with the carboxyl groups on benzene-1,3,5-tricarboxylic acid (H3 BTC) to form a 2D-MOF structure. Structural characterizations, including SEM, TEM, and XRD are conducted to verify that the TFC-MOF is a terrace-like layered structure with uniform-sized mesoporous, which reduces the adsorption steric hindrance and facilitates the mass and electron transfer efficiency of OER. The TFC-MOF shows low overpotential, 255 mV at a current density of 10 mA cm-2 , and a low Tafel slope of 49.9 mV dec-1 , in an alkaline solution. This work provides a planar coordination strategy to synthesize 2D-MOF OER electrocatalyst on a large scale with low cost and low energy consumption, which will promote its practical OER applications.

Construction of a novel ferrihydrite/MoS2 heterogeneous Fenton-like catalyst for efficient degradation of organic pollutants under neutral conditions

In this work, we have fabricated a novel Fenton-like ferrihydrite/MoS2 (Fh/MoS2) composite and verified that the introduction of a small amount of iron on the surface of MoS2 can directly promote the exposure of Mo4+, finally enhancing the catalytic activity of the catalyst. Even though the content of iron element is only 1.19% in the composite, the reaction rate constant of Fh/MoS2 system for the degradation of environmental pollutants, such as organic dyes, antibiotic, and ionic liquid, is all much better than that of pure MoS2 system, which is attributed to much more generation of reactive oxygen species derived from synergistic effect of Fe3+/Fe2+ and Mo4+/Mo6+ redox cycles. The results of XPS and low-temperature EPR confirm that the exposure amount of Mo4+ active sites of 10% Fh/MoS2 is greatly increased, which is conducive to the conversion of Fe3+ to Fe2+ in the reaction process, thus effectively promoting the activation of H2O2.

Modified air-Fenton with MIL-88A for chemical oxygen demand treatment in used coolant oil

Coolant oil from auto part manufacturing contains additives resulting in high chemical oxygen demand (COD) in wastewater. In this study, COD treatment of coolant oil was investigated in a metal-organic framework (MOF) with MIL-88A by a modified air-Fenton (MAF) process by varying synthetic coolant oil concentrations (1-5%), pH (3-9), air-flow rate (1-2 L/min), amount of MIL-88A (0.2-1.0 g), and reaction time (30-180 min). The results were analyzed using central composite design (CCD) and response surface methodology (RSM) using Minitab ver. 19. The characteristic MIL-88A was characterized by XRD that showed a spindle-like shape with 2θ at 10.2° and 13.0°. The FTIR spectrum revealed the vibrational frequencies at Fe-O (564 cm-1), C-O (1391 and 1600 cm-1), and C = O (1216 and 1710 cm-1). The optimum treatment efficiency was studied from 30 CCD conditions in the presence of coolant oil (5%, COD ~ 132,000 mg/L), pH (9), air flow rate (2 L/min), and MIL-88A (1 g) within 177 min. The results obtained from the experiment and the COD prediction were found to be 92.64% and 93.45%, respectively. The main mechanism of iron(III) in MIL-88A is proposed to be the production of hydroxyl radical (·OH) that oxidizes the organic matter in the coolant oil. Moreover, the MAF process was applied to the used industrial coolant oil and was found to be 62.59% efficient.

Design of amphoteric MOFs-cellulose based composite for wastewater remediation: Adsorption and catalysis

Water pollution remains a serious problem for aquatic organism and human beings. Developing an efficient material which can simultaneously remove and convert pollutants into low or no harmful compounds is an essential issue. Targeting at this goal, a multifunctional and amphoteric wastewater treatment material of Co-MOF and functionalized cellulose-based composite (CMC/SA/PEI/ZIF-67) was designed and prepared. Carboxymethyl cellulose (CMC) and sodium alginate (SA) were selected as support to construct an interpenetrating network structure and made it crosslinked with polyethyleneimine (PEI) for further in situ growth of ZIF-67 with good dispersion. The material was characterized using an appropriate set of spectroscopic and analytical techniques. When applied in the adsorption of heavy metal oxyanions with no adjustment of pH, the adsorbent could completely decontaminate Cr(VI) at both low and high initial concentrations with good reduction rates. The adsorbent maintained good reusability after five cycles. Meanwhile, the cobalt species of CMC/SA/PEI/ZIF-67 can activate peroxymonosulfate to generate high oxidizing substances (such as SO4-· and ·OH- radicals) to degrade cationic rhodamine B dye within 120 min, thus indicating the amphoteric and catalytic nature of our CMC/SA/PEI/ZIF-67 adsorbent. The mechanism of the adsorption and catalytic process was also discussed based with the assistance of different characterization analysis.

Heterogeneous photo-Fenton catalyst α-Fe2O3@g-C3N4@NH2-MIL-101(Fe) with dual Z-Scheme heterojunction for degradation of tetracycline

A novel photo-Fenton catalyst α-Fe2O3@g-C3N4@NH2-MIL-101(Fe) (FGN) with dual Z-scheme heterojunction was successfully prepared by hydrothermal method to degrade tetracycline (TC). The preparation conditions were optimized by orthogonal test, and the successful synthesis was confirmed by characterization analyses. The prepared FGN showed better light absorption performance, higher photoelectrons-holes separation efficiency, lower photoelectrons transfer resistance, and higher specific surface area and pore capacity compared with α-Fe2O3@g-C3N4 and α-Fe2O3. The effects of experimental conditions on the catalytic degradation of TC were investigated. The degradation rate of 10 mg/L TC could reach 98.33% within 2 h when the dosage of FGN was 200 mg/L, and the degradation rate could remain 92.27% after 5 times of reuse. Furthermore, the XRD spectra and XPS spectra of FGN before and after reuse were compared to explore the structural stability and catalytic active sites of FGN, respectively. According to the identification of oxidation intermediates, three degradation pathways of TC were proposed. Through H2O2 consumption experiment, radical-scavenging experiments, EPR results, the mechanism of the dual Z-scheme heterojunction was proved. The improved performance of FGN was attributed to the dual Z-Scheme heterojunction effectively promoting the separation of photogenerated electrons from the holes and accelerating the electrons transfer, and the increase of the specific surface area.

A Novel Platform of MOF for Sonodynamic Therapy Advanced Therapies

Metal-organic frameworks (MOFs) combined with sonodynamic therapy (SDT) have been introduced as a new and efficient treatment method. The critical advantage of SDT is its ability to penetrate deep tissues and concentrate energy on the tumor site to achieve a non-invasive or minimally invasive effect. Using a sonosensitizer to generate reactive oxygen species (ROS) under ultrasound is the primary SDT-related method of killing tumor cells. In the presence of a sonosensitizer, SDT exhibits a more lethal effect on tumors. The fast development of micro/nanotechnology has effectively improved the efficiency of SDT, and MOFs have been broadly evaluated in SDT due to their easy synthesis, easy surface functionalization, high porosity, and high biocompatibility. This article reviews the main mechanism of action of sonodynamic therapy in cancer treatment, and also reviews the applications of MOFs in recent years. The application of MOFs in sonodynamic therapy can effectively improve the targeting ability of SDT and the conversion ability of reactive oxygen species, thus improving their killing ability on cancer cells. This provides new ideas for the application of micro/nano particles in SDT and cancer therapy.

Effects and Mechanisms of Cu Species in Fe-MOFs on Fenton-Like Catalytic Activity and Stability

Fe-based MOFs (Fe-MOFs) are deemed promising Fenton-like catalysts due to their well-developed pores and accessible active sites. However, their inferior catalytic activity, iron leaching, and low H₂O₂ utilization always hinder their application as Fe-based MOF catalysts. In this work, we manipulated the structure of Fe-oxo nodes in MIL-88B(Fe) via a Cu^I species substitution method, affording a mixed-valence (Cu-incorporated Fe-MOFs) with highly improved Fenton-like performance. It is found that the Cu^I serves as a shuttle to promote transfer between Fe^II/Fe^III, inducing the formation of a larger amount of stable Fe^II sites, which was proven by experimental and DFT calculation results. A linear relationship was observed for the Fenton-like performance and the amount of Cu^I species for the catalysts. The corresponding value of the ^•OH formation is 2.17 eV for Cu-incorporated MIL-88B(Fe), which is significantly lower than that of MIL-88B(Fe) (2.69 eV). Meanwhile, the enriched Cu^I species suppress Fe species leaching during the catalytic reaction. The Fe-ion leakage of 0.4Cu@MIL-88B is very tiny (0.01-0.03 mg/L), significantly less than that of MIL-88B (2.00-3.02 mg/L). At the same time, H₂O₂ utilization for 0.4Cu@ MIL-88B(Fe) is 88%, which is almost 4.4 times that of pure MIL-88B(Fe). This work provides insights into the rational design of Fe-MOFs as promising Fenton-like catalysts for wastewater treatment.

Controllable synthesis of copper-organic frameworks via ligand adjustment for enhanced photo-Fenton-like catalysis

The efficient heterogeneous photo-Fenton-like catalysts based on two secondary ligand-induced Cu(II) metal-organic frameworks (Cu-MOF-1 and Cu-MOF-2) were constructed for the first time and investigated for the degradation of multiple antibiotics. Herein, two novel Cu-MOFs were prepared using mixed ligands by a facile hydrothermal method. The one-dimensional (1D) nanotube-like structure could be obtained by using V-shaped, long and rigid 4,4'-bis(3-pyridylformamide)diphenylether (3-padpe) ligand in Cu-MOF-1, while polynuclear Cu cluster could be prepared more easily by using short and small isonicotinic acid (HIA) ligand in Cu-MOF-2. Their photocatalytic performances were measured by degradation of multiple antibiotics in Fenton-like system. Comparatively, Cu-MOF-2 exhibited superior photo-Fenton-like performance under visible light irradiation. The outstanding catalytic performance of Cu-MOF-2 was ascribed to the tetranuclear Cu cluster configuration and excellent ability of photoinduced charge transfer and hole separation thus improved the photo-Fenton activity. In addition, Cu-MOF-2 showed high photo-Fenton activity in wide pH working range 3-10 and maintained wonderful stability after five cyclic experiments. The degradation intermediates and pathways were deeply studied. The main active species h⁺, O₂^- and OH worked together in photo-Fenton-like system and possible degradation mechanism was proposed. This study provided a new approach to design the Cu-based MOFs Fenton-like catalysts.

Use of copper sheet in a solar photo-Fenton-like process applied in the treatment of landfill leachate

It is known that copper can be used as catalyst in photo-Fenton-like process; however, there is a lack of information related with its use in the treatment of landfill leachate (LL) in solar photo-Fenton-like processes. Here, we studied the effect of the mass of a copper sheet, the pH of the solution, and the concentration of LL in the removal of the organic matter present in this water. Before the reaction with landfill leachate, the copper sheet used in the reaction was constituted by Cu⁺ and Cu₂O, respectively. The results showed that in a volume of 0.5 L of a pretreated LL, the higher removal of organic matter resulted using a mass of 2.7 g of the copper sheet, a pH of solution of 5, and a concentration of LL of a 10%, obtaining a final value of C/C₀ of chemical oxygen demand (COD) of 0.34, 0.54, 0.66, and 0.84 for concentrations of 25%, 50%, 75%, and 100%, respectively, and 0.0041, 0.0042, 0.0043, and 0.016 for concentration of 25%, 50%, 75%, and 100%, respectively, of C/C₀ of humic acids. The photolysis on LL at its natural pH using solar UV removes very little humic acid and COD, going from 9.4 to 8.5 and 7.7 Abs₂₅₄ for photolysis and UV + H₂O₂, obtaining 8.6 and 17.6% of removal, respectively, and 2.01 and 13.04% removal of COD, respectively. Copper sheet applied under Fenton-like conditions results in 65.9% removal and an increase of 0.2% for humic acid and COD, respectively. Removal using only H₂O₂ for Abs₂₅₄ and COD was 11.95 and 4.3%, respectively. Raw LL produced a 29.1% inhibition of the biological activated sludge rate after the adjustment to pH 7 and the final process of inhibition was 0.23%.

Synthesis and Peroxide Activation Mechanism of Bimetallic MOF for Water Contaminant Degradation: A Review

Metal-organic framework (MOF) materials possess a large specific surface area, high porosity, and atomically dispersed metal active sites, which confer excellent catalytic performance as peroxide (peroxodisulfate (PDS), peroxomonosulfate (PMS), and hydrogen peroxide (H₂O₂)) activation catalysts. However, the limited electron transfer characteristics and chemical stability of traditional monometallic MOFs restrict their catalytic performance and large-scale application in advanced oxidation reactions. Furthermore, the single-metal active site and uniform charge density distribution of monometallic MOFs result in a fixed activation reaction path of peroxide in the Fenton-like reaction process. To address these limitations, bimetallic MOFs have been developed to improve catalytic activity, stability, and reaction controllability in peroxide activation reactions. Compared with monometallic MOFs, bimetallic MOFs enhance the active site of the material, promote internal electron transfer, and even alter the activation path through the synergistic effect of bimetals. In this review, we systematically summarize the preparation methods of bimetallic MOFs and the mechanism of activating different peroxide systems. Moreover, we discuss the reaction factors that affect the process of peroxide activation. This report aims to expand the understanding of bimetallic MOF synthesis and their catalytic mechanisms in advanced oxidation processes.

Three-Dimensional Cadmium-Organic Framework with Dual Functions of Oxygen Evolution in Water Splitting and Fenton-like Photocatalytic Removal of Organic Pollutants

Metal-organic frameworks (MOFs) have exhibited appreciable potential as catalytic agents in the field of material science. The research of new MOFs with dual functions in electrocatalysis and photocatalysis under ultraviolet (UV) irradiation is extremely pivotal for renewable energy applications. Hence, we synthesized a series of three-dimensional MOFs, namely, [Cd(bimb)₂(HITA)₂]_n (Cd-MOF 1), {[Cd(bimb)₆](NO₃)₂}_n (Cd-MOF 2), and [Cd(bimb)₄(ONO₂)₂]_n (Cd-MOF 3) (bimb = 1,4-bis(imidazol-1-ylmethyl)benzene; H₂ITA = 5-hydroxyisophthalic acid), with applicability in the oxygen evolution reaction process and Fenton-like photocatalysis. The obtained results show that Cd-MOF 1 exhibited the most remarkable catalytic performance, affording a current density of 10 mA cm^-2 at a very low overpotential of 279 mV and the smallest Tafel slope of 85.13 mV dec^-1. Meanwhile, these MOFs can generate hydroxyl radicals (•OH) under UV light irradiation with the existence of H₂O₂, enabling the rapid degradation of organic pollutants. This study provides a valuable direction for producing multifunctional and environmentally friendly catalysts.

Embedding Lanthanide Organic Polyhedra into Mesoporous Silica Nanoparticles for the Photocatalytic Degradation of Organic Dyes

Organic pollutants cause severe environmental problems because of their damage to human health and ecological systems. Photocatalytic degradation of persistent organic pollutants is of great importance to address these hazards. Herein, we report a lanthanide organic polyhedra-based hybrid material Gd₈ L₁₂ ⊂MSN with the capability of photocatalytic dye degradation. Gd₈ L₁₂ ⊂MSN was prepared by embedding the Gd₈ L₁₂ complex into mesoporous silica nanoparticles (MSNs) using a "ship-in-a-bottle" strategy. Photocurrent response tests revealed that this hybrid material is a potential semiconductor and could generate a rapid and steady photocurrent upon irradiation. Further dye degradation experiments indicated that it could photocatalyze the degradation of familiar organic dyes. Thereinto, compared with the critical Gd₈ L₁₂ complex, the hybrid material exhibited an acceleration of 2.4 times and realized reusability. This not only offers a potential advanced photocatalyst for degrading persistent organic pollutants, but also provides a strategy for the application of supramolecular materials in environmental science.

Defective iron based metal-organic frameworks derived from zero-valent iron for highly efficient fenton-like catalysis

Introducing crystal defects into iron based metal-organic frameworks (Fe-MOFs) is regarded as a promising strategy to enhance Fenton-like performance. However, developing a facile and effective strategy to construct defective Fe-MOFs as highly efficient Fenton-like catalyst is still a challenge. Herein, MIL-100(Fe) (Def-MIL-100(Fe)) with missing ligands defects was synthesized by a simple heterogeneous reaction using zero-valent iron. The bisphenol A degradation efficiency in the Def-MIL-100(Fe)/H₂O₂ system reached up to 91.26% within 10 min at pH 4 with a low catalyst dosage of 0.05 g/L, while the perfect MIL-100(Fe) has almost no Fenton-like performance. It was observed that missing ligands defects in the Def-MIL-100(Fe) play a key role in the Fenton-like reaction. The missing ligands defects could increase the Lewis acidity for fast H₂O₂ adsorption and accelerate the electron transfer between Fe^II and Fe^III cycling, leading to faster and more·OH generation. Moreover, the missing ligands defects could promote the mass transfer for improving·OH utilization efficiency. This work provides a novel strategy to construct defective Fe-MOFs as highly efficient Fenton-like catalyst to degrade organic pollutants in water.

Hybrid Nanomaterials for Cancer Immunotherapy

Nano-immunotherapy has been recognized as a highly promising strategy for cancer treatment in recent decades, which combines nanotechnology and immunotherapy to combat against tumors. Hybrid nanomaterials consisting of at least two constituents with distinct compositions and properties, usually organic and inorganic, have been engineered with integrated functions and enormous potential in boosting cancer immunotherapy. This review provides a summary of hybrid nanomaterials reported for cancer immunotherapy, including nanoscale metal-organic frameworks, metal-phenolic networks, mesoporous organosilica nanoparticles, metallofullerene nanomaterials, polymer-lipid, and biomacromolecule-based hybrid nanomaterials. The combination of immunotherapy with chemotherapy, chemodynamic therapy, radiotherapy, radiodynamic therapy, photothermal therapy, photodynamic therapy, and sonodynamic therapy based on hybrid nanomaterials is also discussed. Finally, the current challenges and the prospects for designing hybrid nanomaterials and their application in cancer immunotherapy are outlined.

A multivariate metal–organic framework based pH-responsive dual-drug delivery system for chemotherapy and chemodynamic therapy

By combining two different ligands and metals, MOFs can be fine-tuned for effective encapsulation and delivery of two anticancer drugs.

Catalytic Activation of Hydrogen Peroxide Using Highly Porous Hydrothermally Modified Manganese Catalysts for Removal of Azithromycin Antibiotic from Aqueous Solution

Hydrogen peroxide catalytic activation holds great promise in the treatment of persistent pollutants. In this study, the novel Mn-Acacair/Al, Mn-Acacarg/Al and Mn-BTCarg/Al catalysts, supported on Al2O3, were applied for rapid hydrogen peroxide activation and azithromycin antibiotic removal. The catalysts were prepared by the calcination-hydrothermal method under air or argon atmosphere. The characterization confirmed that the modification of manganese with acetylacetonate and benzene-1,3,5-tricarboxylic acid (H3BTC) O-donor ligands highly improves the catalyst porosity, amorphousity, and abundance of coordinately unsaturated sites, which facilitate the generation of reactive oxygen species. The hydrogen peroxide activation and azithromycin removal reached 98.4% and 99.3% after 40 min using the Mn-BTCarg/Al catalyst with incredible stability and reusability. Only a 5.2% decrease in activity and less than 2% manganese releasing in solutions were detected after five regeneration cycles under the optimum operating conditions. The removal intermediates were identified by LC-MS/MS analysis, and the pathways were proposed. The hydroxylation and decarboxylation reactions play a key role in the degradation reaction.