Influence of structural properties on the activity of WO 3 catalysts for visible light photocatalytic ozonation

Graphite/carbon-doped TiO2 nanocomposite synthesized by ultrasound for the degradation of diclofenac

Graphite/C-doped TiO2 nanocomposite was synthesized at room temperature using a simple, impressive, and indirect sonication (20 kHz) by the cup horn system. Tetrabutyltitanate as the precursor of titanium and graphite (G) as the carbon source was used in the preparation of nanocomposite as a photocatalyst. The molar ratio of G/TiO2 as a key parameter was investigated in the synthesis of G/C-doped TiO2. The obtained materials were widely characterized using XRD, SEM, TEM, FTIR, XPS, and UV-Vis diffuse reflectance techniques. The UV-Vis diffuse reflectance spectroscopy results showed that the edge of light absorption of nanocomposite was distinctly red-shifted to the visible area via carbon doping. The XPS outcomes acknowledged the existence of the C, Ti, and O in the photocatalyst. The composite showed an enhancement in the dissociation efficiency of photoinduced charge carriers through the doping process. The photocatalytic activity of the synthesized nanocomposite was checked with diclofenac (DCF) as a pharmaceutical contaminant. The results displayed that G/C-doped TiO2 represented better photocatalytic performance for DCF than TiO2. This was due to the excellent crystallization, intense absorption of visible light, and the impressive separation of photoinduced charge carriers. Various active species such as •OH, •O2¯, h+, and H2O2 play a role in the degradation of DFC. Therefore, different scavengers were used and the role of each one in degradation was investigated. According to the obtained results, •O2¯ radical showed a major role in the photocatalytic process. This work not only proposes a deep insight into the photosensitization-like mechanism by using G-based materials but also develops new photocatalysts for the removal of emerging organic pollutants from waters using sunlight as available cheap energy.

A comprehensive review on metal based active sites and their interaction with O3 during heterogeneous catalytic ozonation process: Types, regulation and authentication

Heterogeneous catalytic ozonation (HCO) was a promising water purification technology. Designing novel metal-based catalysts and exploring their structural-activity relationship continued to be a hot topic in HCO. Herein, we reviewed the recent development of metal-based catalysts (including monometallic and polymetallic catalysts) in HCO. Regulation of metal based active sites (surface hydroxyl groups, Lewis acid sites, metal redox cycle and surface defect) and their key roles in activating O₃ were explored. Advantage and disadvantage of conventional characterization techniques on monitoring metal active sites were claimed. In situ electrochemical characterization and DFT simulation were recommended as supplement to reveal the metal active species. Though the ambiguous interfacial behaviors of O₃ at these active sites, the existence of interfacial electron migration was beyond doubt. The reported metal-based catalysts mainly served as electron donator for O₃, which resulted in the accumulation of oxidized metal and reduced their activity. Design of polymetallic catalysts could accelerate the interfacial electron migration, but they still faced with the dilemma of sluggish Me^(n+m)+/Meⁿ⁺ redox cycle. Alternative strategies like coupling active metal species with mesoporous silicon materials, regulating surface hydrophobic/hydrophilic properties, polaring surface electron distribution, coupling HCO process with photocatalysis and H₂O₂ were proposed for future research.

Complete mineralization of phenolic compounds in visible-light-driven photocatalytic ozonation with single-crystal WO3 nanosheets: Performance and mechanism investigation

Complete mineralization of phenolic compounds into CO₂ and H₂O is desirable for removing them in wastewater, but it is challenging due to the generated recalcitrant intermediates, which requires highly effective advanced oxidation process with proper catalysts. Herein, we found that single-crystal WO₃ nanosheets (NSs)-based photocatalytic ozonation (PCO) can realize complete mineralization of phenols (phenol and 2-chlorophenol) under visible light irradiation. Almost 100% mineralization ratio of phenols was achieved through WO₃ NSs-based PCO system within short time. By comparing their performances with those of polycrystalline WO₃ nanoparticles, detecting and analyzing the intermediates, identifying the dominant radicals and conducting some electrochemical characterizations, the origin of superior catalytic activity of WO₃ NSs was uncovered, the mineralization pathways and the overall mechanism were proposed. The excellent PCO performance of WO₃ NSs was contributed to their nanosheet morphology with single-crystal microstructure and good dispersion, which can provide continuous interior channels for the photogenerated charge transport from the bulk to surface of WO₃ NSs and enough active sites for the surface reactions triggered by these charges. This work puts forwards new ideas to design highly active photocatalysts for PCO and helps deepen understanding of the catalytic mechanism of PCO.

Tungsten-Based Catalysts for Environmental Applications

This review aims to give a general overview of the recent use of tungsten-based catalysts for wide environmental applications, with first some useful background information about tungsten oxides. Tungsten oxide materials exhibit suitable behaviors for surface reactions and catalysis such as acidic properties (mainly Brønsted sites), redox and adsorption properties (due to the presence of oxygen vacancies) and a photostimulation response under visible light (2.6–2.8 eV bandgap). Depending on the operating condition of the catalytic process, each of these behaviors is tunable by controlling structure and morphology (e.g., nanoplates, nanosheets, nanorods, nanowires, nanomesh, microflowers, hollow nanospheres) and/or interactions with other compounds such as conductors (carbon), semiconductors or other oxides (e.g., TiO2) and precious metals. WOx particles can be also dispersed on high specific surface area supports. Based on these behaviors, WO3-based catalysts were developed for numerous environmental applications. This review is divided into five main parts: structure of tungsten-based catalysts, acidity of supported tungsten oxide catalysts, WO3 catalysts for DeNOx applications, total oxidation of volatile organic compounds in gas phase and gas sensors and pollutant remediation in liquid phase (photocatalysis).

Efficient removal of antibiotic thiamphenicol by pulsed discharge plasma coupled with complex catalysis using graphene-WO3-Fe3O4 nanocomposites

Pulsed discharge plasma (PDP) induced complex catalysis for synergetic removal of thiamphenicol (TAP) was investigated using graphene-WO₃-Fe₃O₄ nanocomposites. The prepared samples were characterized systematically in view of the structure and morphology, chemical bonding state, optical property, electrochemical property and magnetic property. Based on characterization and TAP degradation, the catalytic performance followed: graphene-WO₃-Fe₃O₄>graphene-WO₃>WO₃, and the highest removal efficiency and kinetic constant could reached 99.3% and 0.070 min^-1, respectively. With increase of catalyst dosage, the removal efficiency firstly enhanced and then declined. Lower pH value was beneficial for TAP degradation. The prepared graphene-WO₃-Fe₃O₄ owed higher stability and lower dissolution rate of iron ion. The rGO-WO₃-Fe₃O₄ could decompose O₃ and H₂O₂ into more ·OH in PDP system. The degradation intermediates were characterized by fluorescence spectrograph, LC-MS and IC. Based on the detected intermediates and discrete Fourier transform (DFT) analysis, degradation pathway of TAP was proposed. Besides, the toxicity of intermediates was predicted. Finally, catalytic degradation mechanism of TAP by PDP with graphene-WO₃-Fe₃O₄ was summarized.

MOF based engineered materials in water remediation: Recent trends

The significant upsurge in the demand for freshwater has prompted various developments towards water sustainability. In this context, several materials have gained remarkable interest for the removal of emerging contaminants from various freshwater sources. Among the currently investigated materials for water treatment, metal organic frameworks (MOFs), a developing class of porous materials, have provided excellent platforms for the separation of several pollutants from water. The structural modularity and the striking chemical/physical properties of MOFs have provided more room for target-specific environmental applications. However, MOFs limit their practical applications in water treatment due to poor processability issues of the intrinsically fragile and powdered crystalline forms. Nevertheless, growing efforts are recognized to impart macroscopic shapability to render easy handling shapes for real-time industrial applications. Furthermore, efforts have been devoted to improve the stabilities of MOFs that are subjected to fragile collapse in aqueous environments expanding their use in water treatment. Advances made in MOF based material design have headed towards the use of MOF based aerogels/hydrogels, MOF derived carbons (MDCs), hydrophobic MOFs and magnetic framework composites (MFCs) to remediate water from contaminants and for the separation of oils from water. This review is intended to highlight some of the recent trends followed in MOF based material engineering towards effective water regeneration.

Catalysis of rGO-WO3 nanocomposite for aqueous bisphenol A degradation in dielectric barrier discharge plasma oxidation process

Due to the multi-catalysis of the WO₃ and excellent properties of the graphene (GO), a series of rGO-WO₃ nanocomposites were prepared through the hydrothermal synthesis procedure by changing the material ratio, the reaction temperature and the reaction time in this paper, and then added it into a dielectric barrier discharge plasma (DBDP) system for investigating the bisphenol A (BPA)'s degradation and corresponding catalytic mechanism of the rGO-WO₃ in the DBDP system. The obtained results show that there was an optimum dosage of the rGO-WO₃ (40 mg/L) as well as the preparation conditions (5:1000 mass ratio of the GO and the WO₃, 18 h reaction time and 120 °C reaction temperature) for achieving the highest catalytic effect, and the highest degradation rate constant of the BPA was 0.03129 min^-1. The determined higher TOC removal, higher COD removal as well as UV-Vis analysis also demonstrated the catalysis of the rGO-WO₃. The measurement of the change of the O₃ and the H₂O₂ concentrations in the reaction system with or without the rGO-WO₃ and with or without the BPA proved the catalysis of the rGO-WO₃ on the ·OH formation, while the combination of the GO had the positive effect for enhancing the catalytic effect. A figure on the catalysis and degradation procedure of the BPA in the DBDP/rGO-WO₃ system was provided in the paper.

Modeling the Mineralization Kinetics of Visible Led Graphene Oxide/Titania Photocatalytic Ozonation of an Urban Wastewater Containing Pharmaceutical Compounds

In a water ozonation process, dissolved organics undergo two reactions at least: direct ozone attack and oxidation with hydroxyl radicals generated from the ozone decomposition. In the particular case of urban wastewater contaminated with pharmaceuticals, competition between these two reactions can be studied through application of gas–liquid reaction kinetics. However, there is a lack in literature about kinetic modeling of ozone processes in water specially in photocatalytic ozonation. In this work, lumped reactions of ozone and hydroxyl radicals with total organic carbon have been proposed. Urban wastewater containing a mixture of eight pharmaceutical compounds has been used to establish the kinetic model that simulates the mineralization process. The kinetic model is based on a mechanism of free radical and molecular reactions and the knowledge of mass transfer, chemical reaction rate constants, and radiation transfer data. According to the model, both single ozonation and photocatalytic ozonation present two distinct reaction periods characterized by the absence and presence of dissolved ozone. In the first period (less than 10 min), pharmaceuticals mainly disappear by direct ozone reactions and TOC variation due to these compounds has been modeled according to gas–liquid reaction kinetics through a lumped ozone-pharmaceutical TOC fast second order reaction. The corresponding rate constant of this reaction was found to change with time from 3 × 105 to 200 M−1 s−1 with Hatta values higher than 0.3. In the second period (nearly 5 h), competition between direct and hydroxyl radical reactions takes place and a kinetic model based on a direct and free radical reaction mechanism is proposed. Main influencing parameters to be known were: Direct ozone reaction rate constant, catalyst quantum yield, and hydroxyl radical scavengers. The first two take values of 0.5 M−1 s−1 and 5 × 10−4 mol·photon−1, respectively, while a fraction of TOC between 10% and 90% that changes with time was found to possess hydroxyl radical scavenger nature.

A facile synthesis of bismuth oxychloride-graphene oxide composite for visible light photocatalysis of aqueous diclofenac sodium

In this study, bismuth oxychloride/graphene oxide (BiOCl-GO) composite was fabricated by facile one pot hydrothermal method. The pure BiOCl and BiOCl-GO composite was characterized by X-ray diffraction, Transmission electron microscopy X-ray photoelectron spectroscopy and UV-Vis diffuse reflectance spectroscopy. The synthesized composite was then assessed for photocatalytic degradation of diclofenac sodium (DCF) in visible as well as direct solar light and UV irradiation. Results indicated that the photocatalytic removal efficiency of DCF was significantly affected by dose of catalysts, pH value and source of light. The results reveled that degradation efficiency of BiOCl-GO for DCF reduced from 100 to 34.4% with the increases in DCF initial concentration from 5 mg L^-1 to 25 mg L^-1. The solar light degradation of DCF using BiOCl-GO was achieved with apparent rate constant 0.0037 min^-1. The effect of scavengers study revealed that superoxide ions and holes were mainly responsible for DCF degradation. The regeneration study indicates that BiOCl-GO composite can be successfully recycled up to the five cycles. The study revealed the effectiveness of one pot hydrothermal method for the fabrication of BiOCl-GO composite.

Micron-Size White Bamboo Fibril-Based Silane Cellulose Aerogel: Fabrication and Oil Absorbent Characteristics

Micron-size white bamboo fibrils were fabricated from white bamboo and used as a source for the production of highly porous and very lightweight cellulose aerogels for use as a potential oil absorbent. The aerogels were fabricated through gelation from an aqueous alkali hydroxide/urea solution, followed by a conventional freeze-drying process. The morphology and physical properties of the aerogels were characterized by field emission scanning electron microscopy and Brunauer–Emmett–Teller surface area analysis, respectively. Successful silanization of the cellulose aerogel was confirmed by energy-dispersive X-ray spectroscopy, Fourier-transform infrared spectroscopy, and water contact angle measurements. The fabricated silane cellulose aerogel exhibited excellent absorption performance for various oil and organic solvents with typical weight gains ranging from 400% to 1200% of their own dry weight, making them promising versatile absorbents for a range of applications, including water purification.

The role of ozone and influence of band structure in WO3 photocatalysis and ozone integrated process for pharmaceutical wastewater treatment

Photocatalytic ozonation has great potential in wastewater treatment. However, the role of ozone and the contribution of photogenerated hole in this process have not been fully understood. Here three WO₃ materials are synthesized and used as model catalysts in visible-light photocatalytic ozonation for the mineralization of pharmaceutical pollutants. A dual role of ozone in this process has been confirmed: (i) direct oxidation of the pollutant till formation of refractory intermediates, (ii) efficient trapping of photoelectron that cannot be captured by O₂. The latter is crucial because it not only induces the O₃^--mediated pathway for hydroxyl radical (OH) formation but also separates the hole which has proven to be capable of oxidizing water into OH. Evidenced by photoluminescence results, the intrinsic charge separation ability of WO₃ in photocatalytic ozonation is no more as important as that in photocatalysis with O₂. Finally, this process is more applicable under acidic condition. This work contributes to a better understanding of the significance of ozone in WO₃ photocatalytic ozonation and provides us an insight into the mechanism of photocatalytic ozonation.

Nanomaterials for treating emerging contaminants in water by adsorption and photocatalysis: Systematic review and bibliometric analysis

Emerging contaminants in the aquatic environment have become a worldwide problem. Conventional wastewater treatment processes are ineffective for eliminating the emerging contaminants at trace concentrations. Nanomaterials possessing novel size-dependent properties, however, have shown great potential for removing these contaminants. Herein we reviewed nanomaterials reported for removing emerging contaminants by adsorption and/or photocatalysis, and their removal capacity, mechanism, and influencing factors are discussed. Meanwhile, a large-scale bibliometric analysis is conducted on the trends of the emerging contaminants, nanoadsorbents, nanophotocatalysts, and related research topics from the literature during 1998-2017.

Solar or UVA-Visible Photocatalytic Ozonation of Water Contaminants

An incipient advanced oxidation process, solar photocatalytic ozonation (SPO), is reviewed in this paper with the aim of clarifying the importance of this process as a more sustainable water technology to remove priority or emerging contaminants from water. The synergism between ozonation and photocatalytic oxidation is well known to increase the oxidation rate of water contaminants, but this has mainly been studied in photocatalytic ozonation systems with lamps of different radiation wavelength, especially of ultraviolet nature (UVC, UVB, UVA). Nowadays, process sustainability is critical in environmental technologies including water treatment and reuse; the application of SPO systems falls into this category, and contributes to saving energy and water. In this review, we summarized works published on photocatalytic ozonation where the radiation source is the Sun or simulated solar light, specifically, lamps emitting radiation to cover the UVA and visible light spectra. The main aspects of the review include photoreactors used and radiation sources applied, synthesis and characterization of catalysts applied, influence of main process variables (ozone, catalyst, and pollutant concentrations, light intensity), type of water, biodegradability and ecotoxicity, mechanism and kinetics, and finally catalyst activity and stability.

Flexible and durable cellulose aerogels for highly effective oil/water separation

A facile and green method was presented to prepare flexible, ultralight, and hydrophobic CA on the chemical cross-linking of cellulose solution, lyophilization and subsequent hydrophobic modification with methyltrichlorosilane by a CVD process.