A review of the applications of organo-functionalized magnetic graphene oxide nanocomposites for heavy metal adsorption

Adsorption of Cd (II) ions and methyl violet dye by using an agar-graphene oxide nano-biocomposite

In this work, an agar-graphene oxide hydrogel was prepared to adsorb Cd (II) and Methyl Violet (MV) from water. The hydrogel was synthesised and characterised through SEM and EDS. Kinetic, equilibrium and regeneration studies were carried out, in which Langmuir, Freundlich and Sips isotherm models were fitted to the equilibrium experimental data; and regarding the kinetics, studies were conducted by modelling experimental data considering both empirical and phenomenological models. SEM and EDS have shown the composite present a 3D-disordered porous microstructure and that it is mainly constituted of C and O. Sips model fitted well to Cd (II) (R2 = 0.968 and χ2 =  0.176) and MV (R2 = 0.993 and χ2 =  0.783). The qmax values for MV and Cd (II) were 76.65 and 11.70 mg.g-1, respectively. Pseudo-order models satisfactorily described Cd (II) and MV adsorption kinetics with R2 > 0.90. Regeneration experiments revealed an outstanding reuse capacity of the adsorbent after three cycles of adsorption-desorption for both Cd (II) and MV. This study evidences the possibility of a feasible adsorbent for Cd (II) and MV removal from water for successive cycles of use.

Kinetic modeling of the adsorption and desorption of metallic ions present in effluents using the biosorbent obtained from Syagrus romanzoffiana

In this study, the kinetic mechanism of adsorption and desorption, as well as the equilibrium isotherms, of four metallic ions (Cd²⁺, Cu²⁺, Ni²⁺, and Zn²⁺) mono and multicomponent were investigated. The biosorbent used was produced from Jerivá (Syagrus romanzoffiana-commonly known as queen palm) coconut. A kinetic model that considers macropore diffusion as a control step was solved. The finite volume method was used in the discretization of the equations, and the algorithm was implemented in the Fortran programming language. The equilibrium time for monocomponent adsorption was 5 min; for the multicomponent tests, equilibrium occurred instantly (less than 2 min of adsorption). The pseudo-second-order model presented the lowest mean of the sum of normalized errors (SNE) and represented the experimental data of mono and multicomponent adsorption and desorption. Single and multicomponent Langmuir model represented the adsorption isotherms. The maximum capacity of adsorption of metallic ions, both mono and multicomponent, was higher for copper, and the multicomponent adsorption proved to be antagonistic; the presence of co-ions in the solution reduced the removal of metals due to competition between these contaminants. The capture preference order was justified by the physicochemical properties of the ions, such as electron incompatibility and electronegativity. All these situations justified the maximum adsorption of Cu²⁺, followed by Zn²⁺, Cd²⁺, and Ni²⁺ in the mixture.

Insight into the adsorptive removal of ibuprofen using porous carbonaceous materials: A review

Over the last decade, the removal of pharmaceuticals from aquatic bodies has garnered substantial attention from the scientific community. Ibuprofen (IBP), a non-steroidal anti-inflammatory drug, is released into the environment in pharmaceutical waste as well as medical, hospital, and household effluents. Adsorption technology is a highly efficient approach to reduce the IBP in the aquatic environment, particularly at low IBP concentrations. Due to the exceptional surface properties of carbonaceous materials, they are considered ideal adsorbents for the IBP removal of, with high binding capacity. Given the importance of the topic, the adsorptive removal of IBP from effluent using various carbonaceous adsorbents, including activated carbon, biochar, graphene-based materials, and carbon nanostructures, has been compiled and critically reviewed. Furthermore, the adsorption behavior, binding mechanisms, the most effective parameters, thermodynamics, and regeneration methods as well as the cost analysis were comprehensively reviewed for modified and unmodified carbonaceous adsorbents. The compiled studies on the IBP adsorption shows that the IBP uptake of some carbon-based adsorbents is significantly than that of commercial activated carbons. In the future, much attention is needed for practical utilization and upscaling of the research findings to aid the management and sustainability of water resource.

Utilization of KOH-modified fly ash for elimination from aqueous solutions of potentially toxic metal ions

Long-term accumulation of toxic heavy metals in the environment was a potential hidden danger. High energy consumption, complicated operation and low adsorption capacity were the disadvantages of most current adsorbents. This study used one-step modification of fly ash (FA) by low-temperature melting method with KOH as the activator to generate modified fly ash (KFA) with high adsorption capacity to remove heavy metals from aqueous solutions. Various characterization results revealed a destruction that occurred on the surface structure of adsorbent, 12 times increase in specific surface area, and metal ions were successfully adsorbed onto KFA surface. Furthermore, adsorption proceeded most favorably at pH of 5, the presence of ionic strength and co-existing cations significantly influenced the adsorption effects. The description of adsorption data was more suitable by pseudo-second-order kinetics and Langmuir isotherm models. And in single system at 25 °C, for Pb(II), Cu(II), and Cd (II), the q_m were 337.41, 310.09 and 125.00 mg·g^-1. However, in ternary system, the q_m decreased for all three ions in the order Pb(II) > Cu(II) > Cd(II), which was different from the law in single system, and the Pb(II) adsorption was found to have a significant inhibited effect on adsorption of Cd(II) and Cu(II). The adsorption mechanisms including ion exchange, electrostatic attraction and complexation were revealed. And by exploring the bioaccessibility of absorbed heavy metals in four simulated digestive fluids, it was found that KFA could load heavy metal ions and enable their release in organisms and other aquatic environments, which provided the possibility for subsequent related studies. Therefore, KFA with low energy consumption and high adsorption capacity is equipped a prospective development space on removing heavy metals from wastewater.

Removal of organic and inorganic effluents from wastewater by using degradation and adsorption properties of transition metal-doped nickel ferrite

Removal of water pollutants (methylene blue dye and heavy metals) was achieved by zinc/manganese-doped nickel ferrites (Ni_{1 - x}M_xFe₂O₄, where x = 0.00, 0.025, 0.10). Degradation of dye was achieved under natural solar light illumination. Degradation studies of dye were conducted under different parameters such as contact time-80 min, dye's concentration-5 mg/L, pH-7, and dosage of ferrites-15 mg. The adsorption of dye was studied using non-linear kinetics models (pseudo-first-order and pseudo-second-order) and isotherm models (Langmuir and Freundlich). The adsorption of dye followed pseudo-first-order kinetics (R² = 0.99377) than second-order kinetics (R² = 0.98063) and Langmuir isotherm model (R² = 0.96095) than Freundlich model (R² = 0.95962) with maximum adsorption efficiency of 29.62 mg/g. Doping of nickel ferrites caused an increase in the removal percentage of methylene blue dye (80 to 90%) and inorganic effluents (75 to 95% for lead and 47 to 82% for cadmium). In addition to this, band gap energy (2.43 to 3.26 eV) (UV-Vis spectroscopy), pore radius (65.2 to 74.8 A°), and specific surface area (16.45 to 27.95 m²/g) (BET analysis) were also increased. Generally, the results of the study revealed that synthesized nanoparticles can act as potential candidate for the removal of effluents from wastewater under optimum parameters along with recyclability, reusability, and separation under the influence of a magnetic field.

Effect of Functional Group Modifications on the Photocatalytic Performance of g-C3 N4

In recent years, photocatalysis has received increasing attention in alleviating energy scarcity and environmental treatment, and graphite carbon nitride (g-C₃ N₄ ) is used as an ideal photocatalyst. However, it still remains numerous challenges to obtain the desirable photocatalytic performance of intrinsic g-C₃ N₄ . Functional group functionalization, formed by introducing functional groups into the bulk structure, is one of the common modification techniques to modulate the carrier dynamics and increases the number of active sites, offering new opportunities to break the limits for structure-to-performance relationship of g-C₃ N₄ . Nevertheless, the general overview of the advance of functional group modification of g-C₃ N₄ is less reported yet. In order to better understand the structure-to-performance relationship at the molecular level, a review of the latest development of functional group modification is urgently needed. In this review, the functional group modification of g-C₃ N₄ in terms of structures, properties, and photocatalytic activity is mainly focused, as well as their mechanism of reaction from the molecular level insights is explained. Second, the recent progress of the application of introducing functional groups in g-C₃ N₄ is introduced and examples are given. Finally, the difficulties and challenges are presented, and based on this, an outlook on the future research development direction is shown.

Influence of the surface modification of granular-activated carbon synthesized from macauba on heavy metal sorption

Adsorption on activated carbon is a promising technique for the treatment of low-concentration heavy metal pollutants in water with high efficiency and simple operation. However, commercial-activated carbon is often associated with high costs. Therefore, much attention has been given to activated carbon derived from low-cost agricultural and residual biomass. In this work, adsorption of Zn, Cd, and Pb ions in aqueous solutions was conducted using granular-activated carbon obtained from macauba palm, biomass waste of biofuel production, after surface modification using different methods. The adsorbents were obtained in granular form which facilitates all steps of the use, recovery, and reuse of the material, differently from the powdered-activated carbon normally used. The materials were characterized by using XPS, elemental analysis, N₂ sorption (BET method), and zeta potential measurements. Such techniques allowed observation of the functionalization of the carbon surface. The materials presented high adsorption capacities when compared to other works in the literature, with a capacity of approximately 7.69, 8.42, and 1.63 mmol g^-1 for Zn²⁺, Cd²⁺, and Pb²⁺, respectively. In addition, the materials showed a high capacity to be reused, removing 75% of Pb and 99% of both Cd and Zn after 4 cycles.

Nickel removal from wastewater using electrocoagulation process with zinc electrodes under various operating conditions: performance investigation, mechanism exploration, and cost analysis

Economically feasible approaches are needed for wastewater treatment. Electrocoagulation (EC) is an electrochemical treatment method that removes various pollutants from wastewater. It has grown in popularity over conventional treatment methods, especially in industrial wastewater, due to its high performance and the ability to remove toxic compounds. However, it is crucial to reduce the costs associated with EC for widespread implementation. It is also important to decrease nickel (Ni) concentrations in wastewater to prevent potential health and environmental problems. Therefore, this study investigates Ni removal from synthetic and real wastewater using electrocoagulation. Zinc, as a novel electrode, was used as the sacrificial anode. Several operating conditions were assessed, including current density, initial pH, electrolysis time, and spacing between electrodes. The maximum Ni removal efficiency, after 90 min, reached 99.9% at a current density of 10 mA/cm2 when the pH was 9.2 and the gap distance was 4 cm. The Ni removal rate reached 94.4% and 94.9% at a 2- and 6-cm spacing, respectively, after 90 min. Anode morphology, kinetic modeling, electrical energy consumption, and cost analysis were also investigated. The type of corrosion was uniform, which is easily predicted compared to pitting corrosion. The comparison between chemical coagulation and electrocoagulation was also reported. Experimental results indicated that the maximum Ni removal rates reached 99.89% after 90 min. The optimum spacing between electrodes was 4 cm, and the optimum current density was 10 mA/cm2. Additionally, the kinetic data were best represented through the second-order Lagergren model. The results demonstrated that the electrocoagulation performance was better than that of chemical coagulation for Ni removal. The maximum electrical energy consumption was 23.79 KWh/m3 for Ni removal.

WITHDRAWN: Heavy metal ions and dyes removal from aqueous solution using Aloevera-based biosorbent: A systematic review

This article has been withdrawn: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy). This article has been withdrawn at the request of the authors, editor and publisher. The publisher regrets that an error occurred which led to the premature publication of this paper. The publisher apologizes to the readers for this unfortunate erro

Rapid growth of MXene-based membranes for sustainable environmental pollution remediation

Water consumption has grown in recent years due to rising urbanization and industry. As a result, global water stocks are steadily depleting. As a result, it is critical to seek strategies for removing harmful elements from wastewater once it has been cleaned. In recent years, many studies have been conducted to develop new materials and innovative pathways for water purification and environmental remediation. Due to low energy consumption, low operating cost, and integrated facilities, membrane separation has gained significant attention as a potential technique for water treatment. In these directions, MXene which is the advanced 2D material has been explored and many applications were reported. However, research on MXene-based membranes is still in its early stages and reported applications are scatter. This review provides a broad overview of MXenes and their perspectives, including their synthesis, surface chemistry, interlayer tuning, membrane construction, and uses for water purification. Application of MXene based membrane for extracting pollutants such as heavy metals, organic contaminants, and radionuclides from the aqueous water bodies were briefly discussed. Furthermore, the performance of MXene-based separation membranes is compared to that of other nano-based membranes, and outcomes are very promising. In order to shed more light on the advancement of MXene-based membranes and their operational separation applications, significant advances in the fabrication of MXene-based membranes is also encapsulated. Finally, future prospects of MXene-based materials for diverse applications were discussed.

Preparation and Application of Graphene–Based Materials for Heavy Metal Removal in Tobacco Industry: A Review

Heavy metals are nondegradable in the natural environment and harmful to the ecological system and human beings, causing an increased environmental pollution problem. It is required to remove heavy metals from wastewater urgently. Up until now, various methods have been involved in the heavy metal removals, such as chemical precipitation, chemical reduction, electrochemical, membrane separation, ion exchange, biological, and adsorption methods. Among them, adsorption by graphene–based materials has attracted much more attentions for the removal of heavy metals from wastewater systems in recent years, arising due to their large specific surface area, high adsorption capacity, high removal efficiency, and good recyclability. Therefore, it is quite important to review the heavy metal removal with the graphene–based material. In this review, we have summarized the physicochemical property and preparation methods of graphene and their adsorption property to heavy metals. The influencing parameters for the removal of heavy metals by graphene–based materials have been discussed. In addition, the modification of graphene–based materials to enhance their adsorption capability for heavy metal removal is also reviewed. The heavy metal removal by modified graphene–based materials in the tobacco industry has been especially described in detail. Finally, the future trend for graphene–based materials in the field of heavy metal wastewater treatment is proposed. This knowledge will have great impacts on the field and facilitate the researchers to seek the new functionalization method for graphene–based materials with high adsorption capacity to heavy metals in the tobacco industry in the future.

Graphene-Based Adsorbents for Arsenic, Fluoride, and Chromium Adsorption: Synthesis Methods Review

Water contamination around the world is an increasing problem due to the presence of contaminants such as arsenic, fluoride, and chromium. The presence of such contaminants is related to either natural or anthropogenic processes. The above-mentioned problem has motivated the search for strategies to explore and develop technologies to remove these contaminants in water. Adsorption is a common process employed for such proposals due to its versatility, high adsorption capacity, and lower cost. In particular, graphene oxide is a material that is of special interest due to its physical and chemical properties such as surface area, porosity, pore size as well as removal efficiency for several contaminants. This review shows the advances, development, and perspectives of materials based on GO employed for the adsorption of contaminants such as arsenite, arsenate, fluoride, and hexavalent chromium. We provided a detailed discussion of the synthesis techniques and their relationship with the adsorption capacities and other physical properties as well as pH ranges employed to remove the contaminants. It is concluded that the adsorption capacity is not proportional to the surface area in all the cases; instead, the synthesis method, as well as the functional groups, play an important role. In particular, the sol-gel synthesis method shows better adsorption capacities.

Microgels based on 0D-3D carbon materials: Synthetic techniques, properties, applications, and challenges

Microgels are three-dimensional (3D) colloidal hydrogel particles with outstanding features such as biocompatibility, good mechanical properties, tunable sizes from submicrometer to tens of nanometers, and large surface areas. Because of these unique qualities, microgels have been widely used in various applications. Carbon-based materials (CMs) with various dimensions (0-3D) have recently been investigated as promising candidates for the design and fabrication of microgels because of their large surface area, excellent conductivity, unique chemical stability, and low cost. Here, we provide a critical review of the specific characteristics of CMs that are being incorporated into microgels, as well as the state-of-the art applications of CM-microgels in pollutant adsorption and photodegradation, H₂ evoluation, CO₂ capture, soil conditioners, water retention, drug delivery, cell encapsulation, and tissue engineering. Advanced preparation techniques for CM-microgel systems are also summarized and discussed. Finally, challenges related to the low colloidal stability of CM-microgels and development strategies are examined. This review shows that CM-microgels have the potential to be widely used in various practical applications.

Isotherm models for adsorption of heavy metals from water - A review

Adsorption is a widely used technology for removing and separating heavy metal from water, attributed to its eco-friendly, cost-effective, and high efficiency. Adsorption isotherm modeling has been used for many years to predict the adsorption equilibrium mechanism, adsorption capacity, and the inherent characteristics of the adsorption process, all of which are substantial in evaluating the performance of adsorbents. This review summarizes the development history, fundamental characteristics, and mathematical derivations of various isotherm models, along with their applicable conditions and application scenarios in heavy metal adsorption. The latest progress in applying isotherm models with a one-parameter, two-parameter, and three-parameter in heavy metal adsorption using carbon-based materials, which has gained much attention in recent years as low-cost adsorbents, is critically reviewed and discussed. Several experimental factors affecting the adsorption equilibrium, such as solution pH, temperature, ionic strength, adsorbent dose, and initial heavy metal concentration, are briefly discussed. The criteria for selecting the optimum isotherm for heavy metal adsorption are proposed by comparing various adsorption models and analyzing mathematical error functions. Finally, the relative performance of different isotherm models for heavy metal adsorption is compared, and the future research gaps are identified.

A back propagation neural network model for accurately predicting the removal efficiency of ammonia nitrogen in wastewater treatment plants using different biological processes

Accurately predicting the water quality of treated water from a water treatment plant (WWTP) based on the obtained operating database is of great significance. However, it is difficult for common mechanistic models to work well. In this study, a back propagation artificial neural network (BPANN) model with high accuracy was developed to predict the denitrification efficiency based on a 1-year operating database. Standardized principal component analysis (PCA) methods were used to address the data, and the PCA processed data exhibited the best accuracy. In three WWTPs adopting the anaerobic/anoxic/oxic (A²O) process, the ammonia nitrogen removal efficiency of WWTPs was successfully predicted by using five variables: inlet flow rate, pH value, original ammonia nitrogen concentration, Chemical oxygen demand (COD) concentration, and total phosphorus concentration. Importantly, the obtained BPANN model can be effectively used for other widely used treatment processes, such as oxidation ditch (OD), sequencing batch reactor activated sludge process (SBR), membrane bioreactor (MBR), and cyclic activated sludge technology (CAST), by simply optimizing the training data ratios between 50/50 and 90/10. This is the first trial to set up a universal model for predicting the denitrification efficiency of WWTPs adopting common biological processes. The model could be used to choose the optimum treatment process in the new WWTP design or take action in advance to avoid the risk of excessive emissions when the already built WWTPs are subjected to sudden shocks.

Efficient removal of heavy metal ions from aqueous media by unmodified and modified nanodiamonds

This article deals with the adsorption performances of the unmodified nanodiamond (ND) and thermally oxidized nanodiamond (Ox-ND) for the removal of different heavy metal ions such as Fe (III), Cu (II), Cr (VI), and Cd (II) from wastewater. The adsorption capacities of the ions onto adsorbents are higher and follow the order: Ox-ND-3 > Ox-ND-1.5 > ND, which is consistent with their surface areas, zeta potentials, and the presence of carboxyl groups, suggesting that electrostatic attractions between the positive metal ions and the negatively charged adsorbents are the predominant adsorption mechanisms. Adsorption capacities of these adsorbents were found to be 26.8, 31.3, and 45.7 mg/g for Fe (III), 25.2, 30.5, and 44.5 mg/g for Cu (II), 33.6, 44.1, and 55.9 mg/g for Cr (VI), and 40.9, 52.9, and 67.9 mg/g for Cd (II) over ND, Ox-ND-1.5, and Ox-ND-3, respectively. The impact of various operating parameters such as agitation time, initial metal ion concentration, temperature, pH solution, adsorbent dosage, and coexistence of the metal ions on the adsorption performance of Ox-ND-3 towards Cd (II) ions along with the batch adsorption experiments were performed. The equilibrium was reached in 120 min and adsorption data were fitted well with the pseudo-second-order kinetic as well as the Freundlich isotherm models. Adsorption process was spontaneous and exothermic, while the maximum removal efficiency of Cd (II) ions occurred at pH of 6.9 and at 4 g/L dosage. These findings demonstrated that thermally oxidized nanodiamond (Ox-ND) can be a versatile adsorbent to remove the Cd (II) ions from wastewater.

Uptake of arsenic(V) using iron and magnesium functionalized highly ordered mesoporous MCM-41 (Fe/Mg-MCM-41) as an effective adsorbent

Mesoporous silica (MCM-41) is widely used as a supporting material due to its large specific surface area and good stability, but it cannot remove heavy metals due to the lack of adsorption active sites. In this study, the MCM-41 (a mesoporous SiO₂ material) decorated with iron and magnesium oxide (Fe/Mg-MCM-41) was found to be an excellent adsorbent to remove arsenic(V) from water. FTIR, BET, TEM-EDS, XRD, XPS, etc. were applied for characterization analysis. Adsorption isotherms were fitted well by the Langmuir model and the experimental maximum adsorption capacity of Fe/Mg₄-MCM-41 (magnesium accounts for 4%) was 71.53 mg/g at pH = 3. Thermodynamics analysis suggested exothermic nature of adsorption behavior. Kinetic process was well described by the pseudo-second-order model and adsorption rate was controlled by intraparticle diffusion and film diffusion. Moreover, the adsorption behavior of As(V) onto Fe/Mg₄-MCM-41 was investigated under different reaction conditions, such as pH, temperature, Mg-doping and competing ions. The results showed that loading a certain amount of magnesium can significantly improve arsenic removal efficiency. Additionally, Fe/Mg₄-MCM-41 exhibits high arsenic(V) removal in the wide pH range of 3-10. The Fe/Mg₄-MCM-41 can be regenerated and used after four consecutive cycles. The high arsenic(V) sorption capacity, wide range of pH applications, ability to regenerate, and reusability of Fe/Mg₄-MCM-41 confirmed that this adsorbent is promising for treating As-contaminated wastewater.

Graphene Oxide/Polyethylenimine Aerogels for the Removal of Hg(II) from Water

This article reports the synthesis of an aerogel involving reduced graphene oxide (rGO) and polyethylenimine (PEI), and describes its potential application as an effective sorbent to treat Hg(II) contaminated water. The rGO/PEI sorbent was synthetized using a supercritical CO₂ method. N₂ physisorption, electron microscopy, and elemental mapping were applied to visualize the meso/macroporous morphology formed by the supercritical drying. The advantages of the synthetized materials are highlighted with respect to the larger exposed GO surface for the PEI grafting of aerogels vs. cryogels, homogeneous distribution of the nitrogenated amino groups in the former and, finally, high Hg(II) sorption capacities. Sorption tests were performed starting from water solutions involving traces of Hg(II). Even though, the designed sorbent was able to eliminate almost all of the metal from the water phase, attaining in very short periods of time residual Hg(II) values as low as 3.5 µg L⁻¹, which is close to the legal limits of drinking water of 1–2 µg L⁻¹. rGO/PEI exhibited a remarkably high value for the maximum sorption capacity of Hg(II), in the order of 219 mg g⁻¹. All of these factors indicate that the designed rGO/PEI aerogel can be considered as a promising candidate to treat Hg(II) contaminated wastewater.

Insights into Cr(VI) removal mechanism in water by facile one-step pyrolysis prepared coal gangue-biochar composite

The acceleration of industrialization has increased the discharge of chromium-containing wastewater, posing serious threat to the eco-environment and human health. To remove Cr(VI) in wastewater and improve resource utilization of solid waste, coal gangue and rape straw were initially used to prepare coal gangue-rape straw biochar (CG-RS) composite. The effects of pyrolysis temperatures, solution pH, coexisting ions of Cr(VI) adsorption were investigated. Different adsorption models combined with site energy analysis were used to explore the adsorption behaviors and mechanisms. The results showed higher pyrolysis temperature (600 °C) prepared CG-RS had a larger adsorption capacity (9.2 mg/g) for Cr(VI) (pH = 5.0). Analysis of XPS indicated that CG-RS successfully loaded with Fe-O and Al-O functional groups, which mainly participated in the reduction of Cr(VI). Site energy analysis further proved that reduction and surface complexation were the main adsorption mechanisms. This study shows an effective removal of Cr(VI) by CG-RS, providing a new way for resource utilization of solid waste.

Removal of lead ions (Pb2+) from water and wastewater: a review on the low-cost adsorbents

The presence of lead compounds in the environment is an issue. In particular, supply water consumption has been reported to be a significant source of human exposure to lead compounds, which can pose an elevated risk to humans. Due to its toxicity, the International Agency for Research on Cancer and the US Environmental Protection Agency (USEPA) have classified lead (Pb) and its compounds as probable human carcinogens. The European Community Directive and World Health Organization have set the maximum acceptable lead limits in tap water as 10 µg/L. The USEPA has a guideline value of 15 µg/L in drinking water. Removal of lead ions from water and wastewater is of great importance from regulatory and health perspectives. To date, several hundred publications have been reported on the removal of lead ions from an aqueous solution. This study reviewed the research findings on the low-cost removal of lead ions using different types of adsorbents. The research achievements to date and the limitations were investigated. Different types of adsorbents were compared with respect to adsorption capacity, removal performances, sorbent dose, optimum pH, temperature, initial concentration, and contact time. The best adsorbents and the scopes of improvements were identified. The adsorption capacity of natural materials, industrial byproducts, agricultural waste, forest waste, and biotechnology-based adsorbents were in the ranges of 0.8-333.3 mg/g, 2.5-524.0 mg/g, 0.7-2079 mg/g, 0.4-769.2 mg/g, and 7.6-526.0 mg/g, respectively. The removal efficiency for these adsorbents was in the range of 13.6-100%. Future research to improve these adsorbents might assist in developing low-cost adsorbents for mass-scale applications.

Recent development of magnetic biochar crosslinked chitosan on heavy metal removal from wastewater - Modification, application and mechanism

Heavy metal contamination in water bodies is currently in an area of greater concern due to the adverse effects on human health. Despite the good adsorption performance of biochar, various modifications have been performed on the pristine biochar to further enhance its adsorption capability, at the same time overcome the difficulty of particles separation and mitigate the secondary pollution issues. In this review, the feasibility of chitosan-modified magnetic biochar for heavy metal removal from aqueous solution is evaluated by critically analysing existing research. The effective strategies that applied to introduce chitosan and magnetic substances into the biochar matrix are systematically reviewed. The physicochemical changes of the modified-biochar composite are expounded in terms of surface morphology, pore properties, specific surface area, surface functional groups and electromagnetism. The detailed information regarding the adsorption performances of various modified biochar towards different heavy metals and their respective underlying mechanisms are studied in-depth. The current review also analyses the kinetic and isotherm models that dominated the adsorption process and summarizes the common models that fitted well to most of the experimental adsorption data. Moreover, the operating parameters that affect the adsorption process which include solution pH, temperature, initial metal concentration, adsorbent dosage, contact time and the effect of interfering ions are explored. This review also outlines the stability of modified biochar and their regeneration rate after cycles of heavy metal removal process. Lastly, constructive suggestions on the future trends and directions are provided for better research and development of chitosan-modified magnetic biochar.

Introducing a bio sorbent for removal of methylene blue dye based on flexible poly(glycerol sebacate)/chitosan/graphene oxide ecofriendly nanocomposites

As a consequence of industrial activities, one of the most prevalent components in wastewater is Water-soluble dyes needed to be removed. In this research, eco-friendly adsorbents based on poly(glycerol sebacate) (PGS), including PGS-graphene oxide nanoparticles (GO), PGS-graft-chitosan(CS), and PGS-CS-GO nanocomposites, have been proposed as efficient dye adsorbents for the wastewater treatment procedure. FESEM images showed that a smooth and uniform structure was created over incorporating CS into PGS. Besides, the presence of CS within PGS/GO nanocomposites had a positive impact on the exfoliation of GO. Moreover, it was found that the incorporation of both CS and GO into PGS reduced the glass transition of PGS. Besides, their coexistence can probably increase the chain regularity in the polymer matrix and cause a relatively larger crystal size of PGS. In this regard, the ternary nanocomposite saw a Tg value of -29.4 °C. A high adsorption capacity of 178 mg g^-1, as well as 99 removal% efficiency, were observed in the case of the PGS-CS-GO sample after 300 min at a dye concentration of 100 mg L^-1 and pH 7. Additionally, the adsorption capacity value of the adsorbent was preserved around 129 mg g^-1 after 7 cycles of adsorption-desorption. The findings revealed that innovatively synthesized PGS-g-CS/GO nanocomposites could efficiently remove methylene blue from water solutions. Hence, they can be used as a powerful and influential dye adsorbent to purify water solutions.

Two dimensional MXenes as emerging paradigm for adsorptive removal of toxic metallic pollutants from wastewater

Effective methods for removing harmful metals from wastewater have had a huge impact on reducing freshwater scarcity. Because of its excellent removal effectiveness, simplicity and low cost at ambient conditions, adsorption is one of the most promising purifying approaches. MXene-based nanoarchitectures have proven to be effective adsorbents in a variety of harmful metal removal applications. This owes from the distinctive features such as, hydrophilicity, high surface area, electron-richness, great adsorption capacity, and activated metallic hydroxide sites of MXenes. Given the rapid advancement in the design and synthesis of MXene nanoarchitectures for water treatment, prompt updates on this research area are needed that focus on removal of toxic metal, such as production routes and characterization techniques for the advantages, merits and limitations of MXenes for toxic metal adsorption. This is in addition to the fundamentals and the adsorption mechanism tailored by the shape and composition of MXene based on some representative paradigms. Finally, the limits of MXenes are highlighted, as well as their potential future research directions for wastewater treatment. This manuscript may initiate researchers to improve unique MXene-based nanostructures with distinct compositions, shapes, and physiochemical merits for effective removal of toxic metals from wastewater.

Synthesis of EDTA-functionalized graphene oxide-chitosan nanocomposite for simultaneous removal of inorganic and organic pollutants from complex wastewater

Discharging of inorganic and organic pollutants creates a serious threat to the human health and the environment. In the current work, we have synthesized Ethylenediaminetetraacetic acid (EDTA) functionalized graphene oxide-chitosan nanocomposite (GO-EDTA-CS) for simultaneous removal of inorganic (i.e., mercury (Hg(II) and copper (Cu(II)) and organic pollutants (i.e., methylene blue (MB) and crystal violet (CV)) from wastewater via adsorption process. The structural, functional, morphological, elemental compositions, surface area and thermal properties of the synthesized nanocomposite were identified using powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), Brunauer-Emmett-Teller (BET), and thermogravimetric analyzer (TGA), respectively. Different batch adsorption experiments such as pH effect, contact time, initial pollutants concentration, reusability etc. were studied in monocomponent system to optimize the results. The adsorption process apparently followed pseudo-second-order (PSO) kinetics for both pollutants, however the adsorption kinetics was also explained by the intra-particle diffusion model. The isotherm data for both metals ions and dyes were well fit by the Langmuir isotherm model. The maximum adsorption capacities of the adsorbent were determined 324 ± 3.30 130 ± 2.80, 141 ± 6.60, and 121 ± 3.50 mg g^-1 for Hg(II), Cu(II), MB, and CV, respectively. The excellent adsorption capacity was attributed to the availability of various active functional groups (e.g., -COOH, -OH, -NH₂, etc.) on the adsorbent. The EDS, elemental mapping and FTIR analysis performed before and after the adsorption of heavy metals and dyes by GO-EDTA-CS confirmed the simultaneous adsorption of the pollutants. Moreover, GO-EDTA-CS could maintain its adsorption capacity for both inorganic and organic pollutants even after seven cycles of adsorption-desorption, indicating itself a promising adsorbent for practical wastewater treatment containing both inorganic and organic toxic pollutants.

A critical review of the environmental impacts of manufactured nano-objects on earthworm species

The presence of manufactured nano-objects (MNOs) in various consumer or their (future large-scale) use as nanoagrochemical have increased with the rapid development of nanotechnology and therefore, concerns associated with its possible ecotoxicological effects are also arising. MNOs are releasing along the product life cycle, consequently accumulating in soils and other environmental matrices, and potentially leading to adverse effects on soil biota and their associated processes. Earthworms, of the group of Oligochaetes, are an ecologically significant group of organisms and play an important role in soil remediation, as well as acting as a potential vector for trophic transfer of MNOs through the food chain. This review presents a comprehensive and critical overview of toxic effects of MNOs on earthworms in soil system. We reviewed pathways of MNOs in agriculture soil environment with its expected production, release, and bioaccumulation. Furthermore, we thoroughly examined scientific literature from last ten years and critically evaluated the potential ecotoxicity of 16 different metal oxide or carbon-based MNO types. Various adverse effects on the different earthworm life stages have been reported, including reduction in growth rate, changes in biochemical and molecular markers, reproduction and survival rate. Importantly, this literature review reveals the scarcity of long-term toxicological data needed to actually characterize MNOs risks, as well as an understanding of mechanisms causing toxicity to earthworm species. This review sheds light on this knowledge gap as investigating bio-nano interplay in soil environment improves our major understanding for safer applications of MNOs in the agriculture environment.

Adsorptive remediation of environmental pollutants using magnetic hybrid materials as platform adsorbents

Effective separation and remediation of environmentally hazardous pollutants are burning areas of research because of a constant increase in environmental pollution problems. An extensive number of emerging contaminants in the environmental matrices result in serious health consequences in animals, humans, and plants, even at trace levels. Therefore, it is of paramount significance to quantify these undesirable pollutants, even at a very low concentration, from the natural environment. Magnetic solid-phase extraction (MSPE) has recently achieved huge attention because of its strong magnetic domain and easy separation through an external magnetic field compared with simple solid-phase extraction. Therefore, MSPE appeared the most promising technique for removing and pre-concentration of emerging pollutants at trace level. Compared to the normal solid-phase extraction, MSPE as magnetic hybrid adsorbents offers the unique advantages of distinct nanomaterials and magnetic hybrid materials. It can exhibit efficient dispersion and rapid recycling when applying to a very complex matrix. This review highlights the possible environmental applications of magnetic hybrid nanoscale materials as effective MSPE sorbents to remediate a diverse range of environmentally toxic pollutants. We believe this study tends to evoke a variety of research thrust that may lead to novel remediation approaches in the forthcoming years.

Synthesis of “(aminomethyl)phosphonic acid-functionalized graphene oxide”, and comparison of its adsorption properties for thorium(IV) ion, with plain graphene oxide

The current study presents a simple and scalable method for the synthesis of (aminomethyl)phosphonic acid-functionalized graphene oxide (AMPA-GO) adsorbent. The chemical structure of the new material was disclosed by different instrumental analyses (e.g. FTIR, Raman, XPS, AFM, TEM, XRD, CHN, and UV), and two pertinent mechanisms namely nucleophilic substitution and condensation were suggested for its formation. Adsorption experiments revealed that both AMPA-GO and plain GO have a high affinity toward Th(IV) ions, but the AMPA-GO is superior in terms of adsorption capacity, rate of adsorption, selectivity, pH effect, etc. Indeed, the AMPA-GO can uptake Th(IV) nearly instantaneously, and coexisting Na+ ions have no effect on its adsorption. Thanks to Langmuir isotherm, the maximum adsorption capacities of the GO and AMPA-GO were obtained 151.06 and 178.67 mg g−1, respectively. Interestingly, GO and AMPA-GO both showed a higher preference for thorium over uranium so that the average “K d (Th)/K d (U)” for them was 52 and 44, respectively. This data suggests that chromatographic separation of thorium and uranium is feasible by these adsorbents.

Carbon nanotubes/Al2O3 composite derived from catalytic reforming of the pyrolysis volatiles of the mixture of polyethylene and lignin for highly-efficient removal of Pb(ii)

In the present study, the coked catalysts derived from catalytic reforming of the pyrolysis volatiles of polyethylene (PE), lignin (LG) and their mixture were developed as low-cost and environmentally-friendly carbon materials-containing composites to remove heavy metal ions from aqueous solution. The composites were thoroughly characterized by SEM, TEM, XRD, TGA and FT-IR and then their adsorption capability towards Pb(ii) was investigated. It is found that curved cone-shape carbon nanotubes (CNTs) with abundant structural defects and O-containing surface functional groups, such as C–O, C Created by potrace 1.16, written by Peter Selinger 2001-2019 ]]> O and –OH, can be obtained from the catalytic reforming of the mixture of PE and LG. The CNT-containing catalyst composite presents a superior adsorption capability towards Pb(ii) when it is employed in Pb(ii) removal. Adsorption isotherm and adsorption kinetics studies show that the adsorption process can be well simulated by the Langmuir isotherm and pseudo-second-order model, demonstrating that the adsorption is subjected to a homogeneous and chemical process. The calculated maximum adsorption capacity is as high as 146.08 mg g⁻¹, which is much higher than most of the adsorbents reported. Moreover, thermodynamic analysis reveals that the adsorption is spontaneous and endothermic. Accordingly, the used catalyst from the catalytic reforming can be developed as a low-cost and highly-efficient adsorbent.

The coked catalysts derived from catalytic reforming of the pyrolysis volatiles of polyethylene, lignin and their mixture were developed as low-cost and high-efficient carbon materials-containing composites to remove heavy metal ions from water.

Determination of lead ions in fish and oyster samples using a nano-adsorbent of functionalized magnetic graphene oxide nanosheets-humic acid and the flame atomic absorption technique

This study aims at the functionalization of magnetic graphene oxide nanosheets and the binding of humic acid as a lead complex ligand. Graphene oxide nanosheets possess a large surface area and various carboxylic acid groups which can be activated easily by activating agents. Therefore, they are suitable to be used for the extraction of heavy metals. To have a better process of extracting lead ions, magnetic graphene oxide was used in this research. Humic acid, as a lead metal complex agent, has an amine functional group which can be bound to modified graphene oxide from one side. The process of constructing the nano-adsorbent proposed for the preconcentration of lead ions as well as its characterization was studied by infrared spectroscopy (IR), ultraviolet-visible spectroscopy (UV-visible), field emission scanning electron microscopy (FESEM), and vibrating sample magnetometry (VSM). The designed nano-adsorbent was tested to measure lead ions in simulated and real samples of sea water, fish, and oysters. The detection limit obtained in the simulated samples was 0.07 μg/L, and the linear range was 0.2-12 μg/L. The apparatus used to measure the ions was a flame atomic absorption device. In the analysis of the real samples, the values obtained through flame atomic absorption were compared with those obtained through furnace atomic absorption. The proposed technique is advantageous due to being cheap, precise, and sensitive for the trace measurement of lead ions.

Diethylenetriaminepentaacetic acid-thiourea-modified magnetic chitosan for adsorption of hexavalent chromium from aqueous solutions

Chromium pollution is a serious environmental problem given that like most heavy metals, Cr tends to persist and accumulate in the environment. In this study, diethylenetriaminepentaacetic acid-thiourea-modified magnetic chitosan (DTCS-Fe₃O₄) was synthesized for use as an adsorbent for Cr(VI) removal from aqueous solutions. The effects of various treatment conditions on the Cr(VI) adsorption performance of DTCS-Fe₃O₄ composite as well as the kinetics were elucidated. Moreover, by observing the structure and morphology of DTCS-Fe₃O₄, the possible Cr(VI) adsorption mechanism was proposed. DTCS-Fe₃O₄ exhibited a maximum adsorption capacity of 321.3 ± 6.0 mg g^-1. Further, the adsorption process, which followed the Langmuir model for monolayer adsorption, was predominantly governed by chemical adsorption, and could be fitted using the pseudo-second-order kinetics model. Furthermore, given its ease of preparation, low cost, and remarkable performance, it is expected that the DTCS-Fe₃O₄ composite would find wide practical application in the removal of toxic Cr(VI) from wastewater.

Novel nanohybrids for effervescence enhanced magnetic solid-phase microextraction of wide-polarity organic pollutants in roasted meat samples

To simultaneously and efficiently extract pollutants with differential polarities, we herein fabricated and characterized a multifunctional nanocomposite. The novel nanohybrids used NiFe₂ O₄ as magnetic cores, and NH₂ -MIL-101(Al), β-cyclodextrin and graphene oxide as functional components combined with magnetic cores. With the aid of graphene oxide's large π-conjugated system, NH₂ -MIL-101(Al)'s strong adsorption to moderately/strongly polar chemicals, and β-cyclodextrin's specific recognition effect, the nanohybrids realized synergistically efficient extraction of polyaromatic hydrocarbons and bisphenols with a log^Kow range of 3-6. Combined with acidic and alkaline sources, the nanohybrids-based effervescent tablets were prepared. Based on effervescent reaction-enhanced nanohybrids-based efficient adsorption/extraction and high performance liquid chromatography and fluorescence detection, we successfully developed an excellent microextraction method for the simultaneous determination of both polyaromatic hydrocarbons and bisphenols in roasted meat samples. Several important variables were optimized as follows: Na₂ CO₃ and tartaric acid as acidic and alkaline sources, 900 μLof the mixed solvent (acetone and hexane at 2:1 by v/v) as the eluent, 5 min of elution time. Under optimized conditions, the novel method gave low limits of detection (0.07-0.30 μg kg^-1 ), satisfactory recoveries (86.9-103.9%), and high precision (relative standard deviations of 1.9-6.7%) in roasted lamb, beef, pork, chicken, and sausage samples.

Decontamination of radioactive cesium-contaminated soil/concrete with washing and washing supernatant- critical review

We reviewed washing of radioactive Cs-contaminated concrete and soil based on the fate of Cs in concrete and soil, including sorption materials for treatment of supernatant solution. In non-aged cement materials (the calcium silicate hydration (C-S-H) phase), it was possible to decontaminate Cs using ion exchange with monovalent cations, such as NH₄⁺. The clay components in the soil and aggregates were important factors in optimization of the efficiency and mechanism for Cs decontamination with washing solution. The parameters (reagent component, pH, and temperature) of the washing solution should be determined considering soil mineral type (here, weathered biotite (WB) with vermiculite), since monovalent cations such as NH₄⁺ and K⁺ can inhibit Cs decontamination due to collapse of the hydrated and expanded interlayer regions with cation exchange. In this case, hydrothermal treatment or H₂O₂ dosing was necessary to expand the collapsed interlayer region for Cs removal by washing with cation exchange or organic acids. Acid and a chelating agent significantly enhanced Cs-release with dissolution of the adsorbent layer containing iron and aluminum oxides. The important characteristics of important and emerging sorption materials for treatment of the radioactive Cs-contaminated supernatant after washing treatment are discussed. Sorbents for treatment of washing supernatant are divided in to two main categories. Clay minerals, metal hexacyanoferrates, and ammonium molybdophosphates are discussed in the inorganic class of materials. Hypercrosslinked polymers, supramolecular sorbents, carbon nanotubes, and graphene oxide are covered in the carbon-based sorbents for Cs removal from water.

Synthesis of 3D graphene-based materials and their applications for removing dyes and heavy metals

Contamination of water streams by dyes and heavy metals has become a major problem due to their persistence, accumulation, and toxicity. Therefore, it is essential to eliminate and/or reduce these contaminants before discharge into the natural environment. In recent years, 3D graphene has drawn intense research interests owing to its large surface area, superior charge conductivity, and thermal conductivity properties. Due to their unique surface and structural properties, 3D graphene-based materials (3D GBMs) are regarded as ideal adsorbents for decontamination and show great potential in wastewater or exhaust gas treatment. Here, this minireview summarizes the recent progress on 3D GBMs synthesis and their applications for adsorbing dyes and heavy metals from wastewater based on the structures and properties of 3D GBMs, which provides valuable insights into 3D GBMs' application in the environmental field.

Adsorption of Toxic Zinc by Functionalized Lignocellulose Derived from Waste Biomass: Kinetics, Isotherms and Thermodynamics

Heavy metals pollution receives worldwide attention due to great toxicity, significant bio-accumulation and non-biodegradability. Adsorption is a promising technique for removing heavy metals from wastewater. Adsorption of zinc (Zn(II)) from aqueous solution was investigated by functionalized lignocellulose derived from fallen leaves. Alkalized lignocellulose (AC), xanthated lignocellulose (XC) and carboxylated lignocellulose (CC) were characterized by Fourier transform infrared spectrum (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The effect of sorbent dosage, solution pH, sorption time and initial Zn(II) concentration on Zn(II) sorption was investigated by single-factor experiment. Sorption kinetics, isotherms and thermodynamics were examined to reveal sorption mechanism. The sorption capacity and removal rate remarkably depend on experimental variables. Zn(II) sorption onto AC, XC and CC is well described by the pseudo second order kinetics and Langmuir isotherm. The sorption process is fast, reaching sorption equilibrium at 30 min. The maximum sorption capacity of Zn(II) onto CC is 46.49 mg/g, higher than that onto AC, XC and other reported sorbents. Thermodynamic parameters indicate that Zn(II) sorption is a spontaneous process. Sorption mechanism is majorly attributed to surface complexation. This work shows the feasibility of removing toxic Zn(II) from aqueous solution by locally available biomass, providing a sustainable approach for wastewater treatment.

A comprehensive review on magnetic carbon nanotubes and carbon nanotube-based buckypaper for removal of heavy metals and dyes

Industrial effluents contain several organic and inorganic contaminants. Among others, dyes and heavy metals introduce a serious threat to drinking waterbodies. These pollutants can be noxious or carcinogenic in nature, and harmful to humans and different aquatic species. Therefore, it is of high importance to remove heavy metals and dyes to reduce their environmental toxicity. This has led to an extensive research for the development of novel materials and techniques for the removal of heavy metals and dyes. One route to the removal of these pollutants is the utilization of magnetic carbon nanotubes (CNT) as adsorbents. Magnetic carbon nanotubes hold remarkable properties such as surface-volume ratio, higher surface area, convenient separation methods, etc. The suitable characteristics of magnetic carbon nanotubes have led them to an extensive search for their utilization in water purification. Along with magnetic carbon nanotubes, the buckypaper (BP) membranes are also favorable due to their unique strength, high porosity, and adsorption capability. However, BP membranes are mostly used for salt removal from the aqueous phase and limited literature shows their applications for removal of heavy metals and dyes. This study focuses on the existence of heavy metal ions and dyes in the aquatic environment, and methods for their removal. Various fabrication approaches for the development of magnetic-CNTs and CNT-based BP membranes are also discussed. With the remarkable separation performance and ultra-high-water flux, magnetic-CNTs, and CNT-based BP membranes have a great potential to be the leading technologies for water treatment in future.

Lactone radical transformed methyl mercaptan-adsorbed activated carbon into graphene oxide modified activated carbon

Activated carbon was a widely-used adsorbent. However, it was usually classified as a hazardous waste after saturation adsorption for one pollution. For the first time, this article reported a regeneration method for the activated carbon saturated with methyl mercaptan. The regenerated carbon was partially transformed into graphene-oxide fragment with a thickness of 0.9-1.0 nm after a hydrothermal treatment at 180 °C. Electron paramagnetic resonance revealed that lactone group was transformed into lactone radical under the hydrothermal condition. The spins were increased from 4.54E+17-1.24E+18. The formed radical effectively reacted with the adsorbed methyl mercaptan and re-distributed the amorphous activated carbon to form lamellar graphene oxide. As a result, the spins were decreased from 1.24E+18-8.73E+17. At the same time, the amount of lactone group was decreased from 0.71 to 0.42 mmol/g. The regenerated activated carbon thus regained ability to adsorb methyl mercaptan. The main result of this paper puts forward a simple and low-cost method to obtain graphene oxide modified activated carbon from the regeneration of hazardous waste carbon. This conclusion makes contribution to the development of "zero-waste" conception.