Equilibrium and kinetic studies of the adsorption of antibiotics from aqueous solutions onto powdered zeolites

Application of catalytic ozonation using Y zeolite in the elimination of pharmaceuticals in effluents from municipal wastewater treatment plants

Catalytic ozonation using faujasite-type Y zeolite with two different SiO2/Al2O3 molar ratios (60 and 12) was evaluated for the first time in the removal of 25 pharmaceutical compounds (PhCs) present in real effluents from two municipal wastewater treatment plants both located in the Mediterranean coast of Spain. Additionally, control experiments including adsorption and direct ozonation, were conducted to better understand the fundamental aspects of the different individual systems in wastewater samples. Commercial zeolites were used in sodium form (NaY). The results showed that the simultaneous use of ozone and NaY zeolites significantly improved the micropollutants degradation rate, able to degrade 95 % of the total mixture of PhCs within the early 9 min using the zeolite NaY-12 (24.4 mg O3 L-1 consumed), while 12 min of reaction with the zeolite NaY-60 (31 mg O3 L-1 consumed). In the case of individual experiments, ozonation removed 95 % of the total mixture of PhCs after 25 min (46.2 mg O3 L-1 consumed), while the direct adsorption, after 60 min of contact time, eliminated 30 % and 44 % using the NaY-12 and NaY-60 zeolites, respectively. Results showed that the Brønsted acid sites seemed to play an important role in the effectiveness of the treatment with ozone. Finally, the environmental assessment showed that the total risk quotients of pharmaceuticals were reduced between 87 %-99 % after ozonation in the presence of NaY-60 and NaY-12 zeolites. The results of this study demonstrate that catalytic ozonation using NaY zeolites as catalysts is a promising alternative for micropollutant elimination in real-world wastewater matrices.

The introduction of influent sulfamethoxazole loads induces changes in the removal pathways of sulfamethoxazole in vertical flow constructed wetlands featuring hematite substrate

High frequent detection of sulfamethoxazole (SMX) in wastewater cannot be effectively removed by constructed wetlands (CWs) with a traditional river sand substrate. The role of emerging substrate of hematite in promoting SMX removal and the effect of influent SMX loads remain unclear. The removal efficiency of SMX in hematite CWs was significantly higher than that in river sand CWs by 12.7-13.8% by improving substrate adsorption capacity, plant uptake and microbial degradation. With increasing influent SMX load, the removal efficiency of SMX in hematite CWs slightly increased, and the removal pathways varied significantly. The contribution of plant uptake was relatively small (< 0.1%) under different influent SMX loads. Substrate adsorption (37.8%) primarily contributed to SMX removal in hematite CWs treated with low-influent SMX. Higher influent SMX loads decreased the contribution of substrate adsorption, and microbial degradation (67.0%) became the main removal pathway. Metagenomic analyses revealed that the rising influent load increased the abundance of SMX-degrading relative bacteria and the activity of key enzymes. Moreover, the abundance of high-risk ARGs and sulfonamide resistance genes in hematite CWs did not increase with the increasing influent load. This study elucidates the potential improvements in CWs with hematite introduction under different influent SMX loads.

Azithromycin removal using pine bark, oak ash and mussel shell

Adsorption is considered an interesting option for removing antibiotics from the environment because of its simple design, low cost, and potential efficiency. In this work we evaluated three by-products (pine bark, oak ash, and mussel shell) as bio-adsorbents for the antibiotic azithromycin (AZM). Furthermore, they were added at doses of 48 t ha-1 to four different soils, then comparing AZM removal for soils with and without bio-adsorbents. Batch-type experiments were used, adding AZM concentrations between 2.5 and 600 μmol L-1 to the different bio-adsorbents and soil + bio-adsorbent mixtures. Regarding the bio-adsorbents, oak ash showed the best adsorption scores (9600 μmol kg-1, meaning >80% retention), followed by pine bark (8280 μmol kg-1, 69%) and mussel shell (between 3000 and 6000 μmol kg-1, 25-50% retention). Adsorption data were adjusted to different models (Linear, Freundlich and Langmuir), showing that just mussel shell presented an acceptable fitting to the Freundlich equation, while pine bark and oak ash did not present a good adjustment to any of the three models. Regarding desorption, the values were always below the detection limit, indicating a rather irreversible adsorption of AZM onto these three by-products. Furthermore, the results showed that when the lowest concentrations of AZM were added to the not amended soils they adsorbed 100% of the antibiotic, whereas when the highest concentrations of AZM were spread, the adsorption decreased to 55%. However, when any of the three bio-adsorbents was added to the soils, AZM adsorption reached 100% for all the antibiotic concentrations used. Desorption was null in all cases for both soils with and without bio-adsorbents. These results, corresponding to an investigation carried out for the first time for the antibiotic AZM, can be seen as relevant in the search of low-cost alternative treatments to face environmental pollution caused by this emerging contaminant.

Norfloxacin adsorption by torrefied coco peat biochar as a novel adsorbent in a circular economy framework

The current study reported torrefied coco-peat biochar treated at 200 °C, as a novel adsorbent exhibiting phenomenal norfloxacin (NFX) adsorption efficiency. The CHNS analysis confirmed the carbon abundance in the biochar (36.45%), however, XRF analysis indicated a significant presence of K2O (27.73%) and chlorine (7.49%). The XRD and Raman spectral analysis confirmed the amorphous structure of the biochar. Multilayer topology was evident in the SEM micrograph of biochar contributing to its large effective surface area. Additionally, the mesoporous structure of the adsorbent was verified by BET. The adsorption mechanism was predicted to be non-ionic since the zeta potential of both adsorbent and adsorbate was found negative. The process parameters were optimized at 30 °C, pH 6.9, dosage 7 g/L, antibiotic load 494.25 mg/L, and time of 89 min for a maximum of 99.52% adsorption of NFX using Central Composite Design, Analysis of Variance, and Response Surface Methodology. The adsorption process was exothermic, and spontaneous obeying the pseudo-second-order kinetics, while the bulk process was confined to surface adsorption. Isotherm study of NFX adsorption revealed the process to be a favorable, monolayer, and homogeneous adsorption. The NFX molecules were desorbed with an efficiency of 89.19% using 80% ethanol and upon recrystallization, 87.76% of the initial NFX was recovered as crude crystal. Moreover, the NFX removal efficiency was consistent across various water systems, tap water (99.02%), seawater (99.56%), river water (98.92%), pond water (98.26%), and distilled water (99.17%). The techno-economic analysis identified bulk expense as the biochar preparation ($0.82/kg) and the process will be profitable having recovered NFX sold at $6/kg instead of the present retail price ($71/kg). Thus, the study successfully demonstrated a zero-waste, self-sustainable, and revenue-generating water treatment process implementing the circular economy framework.

The Impact of Surface Chemistry and Synthesis Conditions on the Adsorption of Antibiotics onto MXene Membranes

MXene, a two-dimensional (2D) nanomaterial with diverse applications, has gained significant attention due to its 2D lamellar structure, abundance of surface groups, and conductivity. Despite various established synthesis methods since its discovery in 2011, MXenes produced through different approaches exhibit variations in structural and physicochemical characteristics, impacting their suitability for environmental application. This study delves into the effect of synthesis conditions on MXene properties and its adsorption capabilities for four commonly prescribed antibiotics. We utilized material characterization techniques to differentiate MXenes synthesized using three prevalent etchants: hydrofluoric acid (HF), mixed acids (HCl/HF), and fluoride salts (LiF/HCl). Our investigation of adsorption performance included isotherm and kinetic analysis, complemented by density functional theory calculations. The results of this research pinpointed LiF/HCl as an efficient etchant, yielding MXene with favorable morphology and surface chemistry. Electrostatic interactions and hydrogen bonding between MXene surface terminations and ionizable moieties of the antibiotic molecules emerge as pivotal factors in adsorption. Specifically, a higher presence of oxygen terminations increases the binding affinities. These findings provide valuable guidance for etchant selection in environmental applications and underscore the potential to tailor MXenes through synthesis conditions to design membranes capable of selectively removing antibiotics and other targeted substances.

Green surface functionalization of chitosan with spent tea waste extract for the development of an efficient adsorbent for aspirin removal

This study investigates the feasibility of spent tea waste extract (STWE) as a green modifying agent for the modification of chitosan adsorbent towards aspirin removal. Response surface methodology based on Box-Behnken design was employed to find the optimal synthesis parameters (chitosan dosage, spent tea waste concentration, and impregnation time) for aspirin removal. The results revealed that the optimum conditions for preparing chitotea with 84.65% aspirin removal were 2.89 g of chitosan, 18.95 mg/mL of STWE, and 20.72 h of impregnation time. The surface chemistry and characteristics of chitosan were successfully altered and improved by STWE, as evidenced by FESEM, EDX, BET, and FTIR analysis. The adsorption data were best fitted to pseudo 2nd order, followed by chemisorption mechanisms. The maximum adsorption capacity of chitotea was 157.24 mg/g, as fitted by Langmuir, which is impressive for a green adsorbent with a simple synthesis method. Thermodynamic studies demonstrated the endothermic nature of aspirin adsorption onto chitotea.

Modeling of adsorptive removal of azithromycin from aquatic media by CoFe2O4/NiO anchored microalgae-derived nitrogen-doped porous activated carbon adsorbent and colorimetric quantifying of azithromycin in pharmaceutical products

Herein, it was aimed to optimize the removal process of Azithromycin (Azi) from the aquatic environment via CoFe2O4/NiO nanoparticles anchored onto the microalgae-derived nitrogen-doped porous activated carbon (N-PAC), besides developing a colorimetric method for the swift monitoring of Azi in pharmaceutical products. In this study, the Spirulina platensis (Sp) was used as a biomass resource for fabricating CoFe2O4/NiO@N-PAC adsorbent. The pores of N-PAC mainly entail mesoporous structures with a mean pore diameter of 21.546 nm and total cavity volume (Vtotal) of 0.033578 cm3. g-1. The adsorption studies offered that 98.5% of Azi in aqueous media could remove by CoFe2O4/NiO@N-PAC. For the cyclic stability analysis, the adsorbent was separated magnetically and assessed at the end of five adsorption-desorption cycles with a negligible decrease in adsorption. The kinetic modeling revealed that the adsorption of Azi onto the CoFe2O4/NiO@N-PAC was well-fitted to the second-order reaction kinetics, and the highest adsorption capacity was found as 2000 mg. g-1 at 25 °C based on the Langmuir adsorption isotherm model at 0.8 g. L-1 adsorbent concentration. The Freundlich isotherm model had the best agreement with the experimental data. Thermodynamic modeling indicated the spontaneous and exothermic nature of the adsorption process. Moreover, the effects of pH, temperature, and operating time were also optimized in the colorimetric Azi detection. The blue ion-pair complexes between Azi and Coomassie Brilliant Blue G-250 (CBBG-250) reagent followed Beer's law at wavelengths of 640 nm in the concentration range of 1.0 μM to 1.0 mM with a 0.94 μM limit of detection (LOD). In addition, the selectivity of Azi determination was verified in presence of various species. Furthermore, the applicability of CBBG-250 dye for quantifying Azi was evaluated in Azi capsules as real samples, which revealed the acceptable recovery percentage (98.72-101.27%). This work paves the way for engineering advanced nanomaterials for the removal and monitoring of Azi and assures the sustainability of environmental protection and public health.

Impregnation of biochar with montmorillonite and its activation for the removal of azithromycin from aqueous media

An inexpensive and environmentally friendly composite synthesized from rice husk, impregnated with montmorillonite and activated by carbon dioxide, was investigated for the removal of azithromycin from an aqueous solution. Various techniques were used to characterize adsorbents in detail. The sorption process was primarily regulated by the solution pH, pollutant concentration, contact duration, adsorbent dose, and solution temperature. The equilibrium data were best analyzed using the nonlinear Langmuir and Sips (R² > 0.97) isotherms, which revealed that adsorption occurs in a homogenous manner. The adsorption capacity of pristine biochar and carbon dioxide activated biochar-montmorillonite composite was 33.4 mg g^-1 and 44.73 mg g^-1, respectively. Kinetic studies identified that the experimental data obeyed the pseudo-second-order and Elovich models (R² > 0.98) indicating the chemisorption nature of adsorbents. The thermodynamic parameters determined the endothermic and spontaneous nature of the reaction. The ion exchange, π-π electron-donor-acceptor (EDA) interactions, hydrogen-bonding, and electrostatic interactions were the plausible mechanisms responsible for the adsorption process. This study revealed that a carbon dioxide activated biochar-montmorillonite composite may be used as an effective, sustainable, and economical adsorbent for the removal of azithromycin from polluted water.

Reductions in abundances of intracellular and extracellular antibiotic resistance genes by SiO2 nanoparticles during composting driven by mobile genetic elements

Applying exogenous additives during the aerobic composting of livestock manure is effective for slowing down the spread of antibiotic resistance genes (ARGs) in the environment. Nanomaterials have received much attention because only low amounts need to be added and they have a high capacity for adsorbing pollutants. Intracellular ARGs (i-ARGs) and extracellular ARGs (e-ARGs) comprise the resistome in livestock manure but the effects of nanomaterials on the fates of these different fractions during composting are still unclear. Thus, we investigated the effects of adding SiO₂ nanoparticles (SiO₂NPs) at four levels (0 (CK), 0.5 (L), 1 (M), and 2 g/kg (H)) on i-ARGs, e-ARGs, and the bacterial community during composting. The results showed that i-ARGs represented the main fraction of ARGs during aerobic composting of swine manure, and their abundance was lowest under M. Compared with CK, M increased the removal rates of i-ARGs and e-ARGs by 17.9% and 100%, respectively. SiO₂NPs enhanced the competition between ARGs hosts and non-hosts. M optimized the bacterial community by reducing the abundances of co-hosts (Clostridium_sensu_stricto_1, Terrisporobacter, and Turicibacter) of i-ARGs and e-ARGs (by 96.0% and 99.3%, respectively) and killing 49.9% of antibiotic-resistant bacteria. Horizontal gene transfer dominated by mobile genetic elements (MGEs) played a key role in the changes in the abundances of ARGs. i-intI1 and e-Tn916/1545 were key MGEs related closely to ARGs, and the maximum decreases of 52.8% and 100%, respectively, occurred under M, which mainly explained the decreased abundances of i-ARGs and e-ARGs. Our findings provide new insights into the distribution and main drivers of i-ARGs and e-ARGs, as well as demonstrating the possibility of adding 1 g/kg SiO₂NPs to reduce the propagation of ARGs.

Adsorption of Methylene Blue and Tetracycline by Zeolites Immobilized on a PBAT Electrospun Membrane

The detection of emerging contaminants in bodies of water has steadily increased in recent years, becoming a severe problem threatening human and ecosystem health. Developing new materials with adsorption properties to remove these pollutants represents an important step toward a potential solution. In this paper, a polybutylene adipate terephthalate (PBAT) nanofibrous membrane incorporating clinoptilolite zeolite was developed and its excellent performance in removing tetracycline (TC) and methylene blue (MB) from water was demonstrated. The composite membrane was prepared in two steps: firstly, a homogeneous dispersion of clinoptilolite (1 wt% respect to polymer) in a PBAT solution (12.6 wt%) was electrospun; secondly, the electrospun membrane was subjected to an acid treatment that improved its wettability through the protonation of the surface silanol groups of clinoptilolite. The resulting membrane was hydrophilic and showed higher adsorption for TC (800 mg/g) and MB (100 mg/g), using a low dose (90 mg/L) powdered zeolite. The maximum removal capacity was obtained at neutral pH, being the cation exchange reaction the main adsorption mechanism. Pseudo-second-order kinetics and Henry's law agree well with the proposed chemisorption and the high affinity of TC and MB for the adsorbent. The material can be reused after the removal process without generating additional contamination, although losing some effectivity.

Adsorptive removal of tetracycline and ciprofloxacin drugs from water by using a magnetic rod-like hydroxyapatite and MIL-101(Fe) metal-organic framework nanocomposite

A novel porous nanocomposite composed of hydroxyapatite nanorods (HAP), a MIL-101(Fe) metal-organic framework, and Fe₃O₄ nanoparticles was successfully fabricated in this work. The magnetic HAP/MIL-101(Fe)/Fe₃O₄ ternary nanocomposite was identified by various techniques, namely FT-IR spectroscopy, XRD, Raman spectroscopy, SEM, EDX, TEM, BET specific surface area, zeta potential, and VSM measurements. Tetracycline (TC) and ciprofloxacin (CIP) aqueous solutions were used to evaluate the adsorption performance of the resulting HAP/MIL-101(Fe)/Fe₃O₄ composite. The adsorption rate and capacity of HAP/MIL-101(Fe)/Fe₃O₄ were increased as compared with HAP, MIL-101(Fe), and HAP/MIL-101(Fe) samples due to the increased attraction. The influence of initial drug concentration, adsorbent dosage, temperature, and pH on the adsorption process was investigated. The results showed that the removal efficiencies of HAP/MIL-101(Fe)/Fe₃O₄ for TC and CIP were 95% and 93%, under the determined optimum conditions: pH of 7, drug concentration of 50 mg L^-1, adsorbent dosage of 30 mg, and temperature of 25 °C. The maximum adsorption capacities of HAP/MIL-101(Fe)/Fe₃O₄ for TC and CIP were 120.48 mg g^-1 and 112.35 mg g^-1, respectively. Reusability of the prepared nanocomposite was easily achieved up to three times without significant change in its structure. As a result, the synthesized magnetic nanocomposite can be reused as a suitable absorbent for TC and CIP removal from aqueous solutions.

Structure, mechanism, and toxicity in antibiotics metal complexation: Recent advances and perspectives

Antibiotic-metal complexes (AMCs) formed by antibiotics and metal ions have attracted considerable attentions in recent years. Although different removal methods for AMCs have been reported in the literature, very few investigations have focused on the mechanisms and toxic effects of antibiotic-metal coordination. This review briefly describes the structural characteristics of various commonly used antibiotics and the coordination mechanisms with metal ions. Considering the complexity of the real environment, various environmental factors affecting AMC formation are highlighted. The effects of AMCs on microbial community structure and the role of metal ions in influencing resistant genes from the molecular perspective are of interest within this work. The toxicities and mechanisms of AMCs on different species of biota are also discussed. These findings underline the need for more targeted detection and analysis methods and more suitable toxicity markers to verify the combination of antibiotics with metal ions and reveal environmental toxicities in future. This review presents an innovative idea that antibiotics combined with metal ions will change the toxicity and environmental behavior of antibiotics.

Magnetic NH(2)-MIL-101(Al)/Chitosan nanocomposite as a novel adsorbent for the removal of azithromycin: modeling and process optimization

In the present study, the magnetic NH₂-MIL-101(Al)/chitosan nanocomposite (MIL/Cs@Fe₃O₄ NCs) was synthesized and used in the removal of azithromycin (AZT) from an aqueous solution for the first time. The as-synthesized MIL/Cs@Fe₃O₄ NCs was characterized by SEM, TEM, XRD, FTIR, BET, and VSM techniques. The effect of various key factors in the AZT adsorption process was modeled and optimized using response surface methodology based on central composite design (RSM-CCD). The low value of p-value (1.3101e-06) and RSD (1.873) parameters, along with the coefficient of determination > 0.997 implied that the developed model was well fitted with experimental data. Under the optimized conditions, including pH: 7.992, adsorbent dose: 0.279 g/L, time: 64.256 min and AZT concentration: 10.107 mg/L, removal efficiency and AZT adsorption capacity were obtained as 98.362 ± 3.24% and 238.553 mg/g, respectively. The fitting of data with the Langmuir isotherm (R²: 0.998, X²: 0.011) and Pseudo-second-order kinetics (R²: 0.999, X²: 0.013) showed that the adsorption process is monolayer and chemical in nature. ΔH° > 0, ΔS° > 0, and ∆G° < 0 indicated that AZT removal was spontaneous and endothermic in nature. The effect of Magnesium on AZT adsorption was more complicated than other background ions. Reuse of the adsorbent in 10 consecutive experiments showed that removal efficiency was reduced by about 30.24%. The performance of MIL/Cs@Fe₃O₄ NCs under real conditions was also tested and promising results were achieved, except in the treatment of AZT from raw wastewater.

Highly effective water hyacinth (Eichhornia crassipes) waste-based functionalized sustainable green adsorbents for antibiotic remediation from wastewater

Azithromycin (AZIM) is considered as one of the most frequently prescribed antibiotics (ABs) in the world by medical professionals. This study explored, two novel, cheap and environmentally beneficial adsorbents i.e., alkali treated water hyacinth powder (AT-WHP) and graphene oxide-water hyacinth-polyvinyl alcohol (GO-WH-PVA) composite, fabricated from water hyacinth (Eichhornia crassipes) waste to remediate AZIM from wastewater. Biosorption experiments were performed by batch and packed-bed column studies and the adsorbents were characterized using various instrumental methods. The morpho-chemical profile of the adsorbents suggested noteworthy AZIM adsorption. AZIM adsorption data can be reasonably explained by pseudo second order (PSO) kinetic model with maximum regression coefficient (R² > 0.99) and lowest Marquardt's present standard deviation (MPSD) and root mean squared error (RMSE) values. The isotherm models recommended Langmuir and Temkin to be the best-fitted, providing highest regression coefficient and lowest error values. Conferring to Langmuir model, the theoretical highest adsorption potentials (q_max) were accounted to be 244.498 and 338.115 mg/g for AT-WHP and GO-WH-PVA, correspondingly, very close to experimental values (q_e, exp). AZIM adsorption processes were governed by the chemisorption mechanisms. The adsorbents had excellent regeneration potential and could be reused several times. In order to scale-up application of the adsorbents, performance of a 100 L packed-bed reactor was assessed and a breakthrough time of adsorption for GO-WH-PVA was 15 min in 5000 mg/L AZIM concentration. Thus, the absorbents synthesized in this study can be considered highly effective at removal of AZIM from wastewater.

Au/Ti Synergistically Modified Supports Based on SiO2 with Different Pore Geometries and Architectures

New photocatalysts were obtained by immobilization of titanium and gold species on zeolite Y, hierarchical zeolite Y, MCM-48 and KIT-6 supports with microporous, hierarchical and mesoporous cubic structure. The obtained samples were characterized by X-ray diffraction (XRD), N2-physisorption, scanning and transmission electron microscopy (SEM/TEM), diffuse reflectance UV–Vis spectroscopy (DRUV-Vis), X-ray photoelectron spectroscopy (XPS), Raman and photoluminescence spectroscopy. The photocatalytic properties were evaluated in degradation of amoxicillin (AMX) from water, under UV (254 nm) and visible light (532 nm) irradiation. The higher degradation efficiency and best apparent rate constant were obtained under UV irradiation for Au-TiO2-KIT-6, while in the visible condition for the Au-TiO2-MCM-48 sample containing anatase, rutile and the greatest percent of Au metallic clusters were found (evidenced by XPS). Although significant values of amoxicillin degradation were obtained, total mineralization was not achieved. These results were explained by different reaction mechanisms, in which Au species act as e− trap in UV and e− generator in visible light.

Antibiotic adsorption by natural and modified clay minerals as designer adsorbents for wastewater treatment: A comprehensive review

Increased antibiotic use worldwide has become a major concern because of their health and environmental impacts. Since most antibiotic residues can hardly be removed from wastewater using conventional treatments, alternative methods receive great attention. Adsorption is one of the most efficient and cost-effective treatment methods for antibiotics. Among the adsorbents, clay minerals have garnered increasing attention due to their unique properties including availability, high specific surface area, low cost, cation exchange capacity, and good removal efficiency. This paper reviews the recent progress made in the use of natural and modified clay minerals for the removal of antibiotics from water. First, the sources, occurrence, removal and health effects of the antibiotics commonly encountered in water bodies are described. Antibiotic concentration levels and average removal efficiencies measured in conventional activated sludge treatment systems worldwide are also provided to better address the problem. Second, the review explores the characteristics of clay minerals as adsorbent of antibiotics and the factors affecting the adsorption. The review identifies and discusses the future trends and strategies used to increase the adsorption capacity of clay minerals by modification and combination techniques (intercalation of novel functional groups such as organocations, biopolymers and metal pillared-clay minerals, combination with biochar or thermal activation). The quantitative comparisons of clay minerals' ability for antibiotic removal are given. Some natural clay minerals have good removal potential for antibiotics, with maximum adsorption capacities over 100 mg/g. For most other adsorbents, surface modifications and combination techniques resulted in improved adsorption properties (including higher surface area, enhanced adsorption capacity, increased stability and mechanical strength). Finally, the application of these adsorbents at pilot scale, using real wastewater samples, their reuse, economic analysis and life cycle assessment are other issues that have been considered.

A Fast Adsorption of Azithromycin on Waste-Product-Derived Graphene Oxide Induced by H-Bonding and Electrostatic Interactions

Graphene oxide (GO) was prepared from the graphite electrode of waste dry cells, and the application of the prepared GO as a potential adsorbent for rapid and effective removal of an antibiotic, azithromycin (AZM), has been investigated. The synthesis process of GO is very simple, cost-effective, and eco-friendly. As-prepared GO is characterized by field-emission scanning electron microscopy, energy-dispersive X-ray, transmission electron microscopy, X-ray diffractometry, Fourier transform infrared spectroscopy, elemental analysis, Brunauer-Emmett-Teller sorptometry, and zeta potential analysis. The obtained GO has been employed for removal of the widely used AZM antibiotic from an aqueous solution. The quantitative analysis of AZM before and after adsorption has been carried out by liquid chromatography tandem mass spectrometry. The adsorption of AZM by GO was performed in a batch of experiments where the effects of adsorbent (GO) dose, solution pH, temperature, and contact time were investigated. Under optimum conditions (pH = 7.0, contact time = 15 min, and adsorbent dose = 0.25 g/L), 98.8% AZM was removed from the aqueous solution. The rapid and effective removal of AZM was significantly controlled by the electrostatic attractions and hydrogen bonding on the surface of GO. Adsorption isotherms of AZM onto GO were fitted well with the Freundlich isotherm model, while the kinetic data were fitted perfectly with the pseudo-second order. Therefore, the simple, cost-effective, and eco-friendly synthesis of GO from waste material could be applicable to fabricate an effective and promising low-cost adsorbent for removal of AZM from aqueous media.

Environmental and Pharmacokinetic Aspects of Zeolite/Pharmaceuticals Systems—Two Facets of Adsorption Ability

Zeolites belong to aluminosilicate microporous solids, with strong and diverse catalytic activity, which makes them applicable in almost every kind of industrial process, particularly thanks to their eco-friendly profile. Another crucial characteristic of zeolites is their tremendous adsorption capability. Therefore, it is self-evident that the widespread use of zeolites is in environmental protection, based primarily on the adsorption capacity of substances potentially harmful to the environment, such as pharmaceuticals, pesticides, or other industry pollutants. On the other hand, zeolites are also recognized as drug delivery systems (DDS) carriers for numerous pharmacologically active agents. The enhanced bioactive ability of DDS zeolite as a drug carrying nanoplatform is confirmed, making this system more specific and efficient, compared to the drug itself. These two applications of zeolite, in fact, illustrate the importance of (ir)reversibility of the adsorption process. This review gives deep insight into the balance and dynamics that are established during that process, i.e., the interaction between zeolites and pharmaceuticals, helping scientists to expand their knowledge necessarily for a more effective application of the adsorption phenomenon of zeolites.

Environmentally azithromycin pharmaceutical wastewater management and synergetic biocompatible approaches of loaded azithromycin@hematite nanoparticles

Pharmaceutical wastewater contamination via azithromycin antibiotic and the continuous emergence of some strains of bacteria, cancer, and the Covid-19 virus. Azithromycin wastewater treatment using the biosynthesized Hematite nanoparticles (α-HNPs) and the biocompatible activities of the resulted nanosystem were reported. Biofabrication of α-HNPs using Echinacea purpurea liquid extract as a previously reported approach was implemented. An evaluation of the adsorption technique via the biofabricated α-HNPs for the removal of the Azr drug contaminant from the pharmaceutical wastewater was conducted. Adsorption isotherm, kinetics, and thermodynamic parameters of the Azr on the α-HNPs surface have been investigated as a batch mode of equilibrium experiments. Antibacterial, anticancer, and antiviral activities were conducted as Azr@α-HNPs. The optimum conditions for the adsorption study were conducted as solution pH = 10, 150 mg dose of α-HNPs, and Azr concentration 400 mg/L at 293 K. The most fitted isothermal model was described according to the Langmuir model at adsorption capacity 114.05 mg/g in a pseudo-second-order kinetic mechanistic at R² 0.9999. Thermodynamic study manifested that the adsorption behavior is a spontaneous endothermic chemisorption process. Subsequently, studying the biocompatible applications of the Azr@α-HNPs. Azr@α-HNPs antibacterial activity revealed a synergistic effect in the case of Gram-positive more than Gram-negative bacteria. IC₅₀ of Azr@α-HNPs cytotoxicity against MCF7, HepG2, and HCT116 cell lines was investigated and it was found to be 78.1, 81.7, and 93.4 µg/mL respectively. As the first investigation of the antiviral use of Azr@α-HNPs against SARS-CoV-2, it was achieved a safety therapeutic index equal to 25.4 revealing a promising antiviral activity. An admirable impact of the use of the biosynthesized α-HNPs and its removal nanosystem product Azr@α-HNPs was manifested and it may be used soon as a platform of the drug delivery nanosystem for the biomedical applications.

Removal of sulfanilamide by tailor-made magnetic metal-ceramic nanocomposite adsorbents

Three tailor-made magnetic metal-ceramic nanocomposites, obtained from zeolite A (ZA1 and ZA2) and a natural clinoptilolite (LB1), have been used as adsorbents to remove sulfanilamide (SA), a sulfonamide antibiotic of common use, from water. A patented process for the synthesis of nanocomposites has been suitably modified to maximize the efficiency of the SA removal, as well as to extend the applicability of the materials. The role played by the main process parameters (kinetic, pH, initial concentration of SA) has been characterized. The significant effect of the pH on the SA removal has been explained identifying two possibly coexisting mechanisms of SA adsorption, based on polar and hydrophobic interactions, respectively. The adsorption kinetics have been in all cases described by the pseudo second-order model. The adsorption isotherms obtained with ZA1 have been satisfactorily described by the Langmuir model, suggesting a monolayer adsorption of SA on the magnetic nanocomposites resulting from a uniform surface energy. The isotherms obtained with LB1 could be described by a more complex approach, deriving by the additive superposition of Langmuir and Sips models. In order to ensure an effective removal of the antibiotic and a proper recycle of the magnetic adsorbents, a sustainable regeneration procedure of the exhausted adsorbent has been developed, based on the treatment with a dilute solution of NaOH.

A study on the adsorption behaviors of three hydrophobic quinolones by ordered mesoporous CMK-3

In this work, a series of ordered mesoporous carbon nanomaterials (CMK-3) have been synthesized by a hard-template method at temperatures of 80 °C, 100 °C and 130 °C, which can serve as adsorbents for efficient adsorption of quinolones in aqueous solutions. The physicochemical properties and the morphologies of these CMK-3 have been well characterized, showing mesoporous channels with the specific surface area reaching up to 1290 m²/g. Adsorption studies have been performed on three hydrophobic quinolones: norfloxacin (NOR), ciprofloxacin (CIP) and enrofloxacin (ENR), with the adsorption capacities of 403 mg/g, 479 mg/g and 510 mg/g, respectively, at room temperature. The adsorption kinetics of the three quinolones are in accordance with the pseudo-second kinetic model, and the adsorption isotherm curves conform to Langmuir isotherm model. Significantly, the adsorption thermodynamics confirms that the adsorption processes are spontaneous endothermic. Finally, the adsorption mechanism has been discussed, which can be attributed to the synergistic effect of pore diffusion, hydrophobic bond, and electron donor-acceptor interaction.

New Polymeric Adsorbents Functionalized with Aminobenzoic Groups for the Removal of Residual Antibiotics

In this paper, we present the synthesis of new polymeric adsorbents derived from macroporous chloromethylated styrene–divinylbenzene (DVB) copolymers with different cross-linking degrees functionalized with the following aminobenzoic groups: styrene—6.7% DVB (PAB1), styrene—10% DVB (PAB2), and styrene—15% DVB (PAB3). The new polymeric products, PAB1, PAB2, and PAB3, were characterized by FTIR spectroscopy, thermogravimetric analysis, and EDX, SEM, and BET analysis, respectively. The evolution of the functionalization reaction was followed by FTIR spectroscopy, which revealed a decrease in the intensity of the γCH₂Cl band at 1260 cm⁻¹, and, simultaneously, the appearance of C=O carboxylic bands from 1685–1695 cm⁻¹ and at 1748 cm⁻¹. The thermal stability increased with the increase in the cross-linking degree. The data obtained from the EDX analysis of the novel cross-linked copolymers confirmed the functionalization with aminobenzoic groups through the presence and content of nitrogen, as follows: PAB1: N% = 0.47; PAB2: N% = 0.85; and PAB3: N% = 1.30. The adsorption performances of the novel polymeric adsorbents, PAB1, PAB2, and PAB3, were tested in the adsorption of three antibiotics, tetracycline, sulfamethoxazole, and amoxicillin, from aqueous solutions, by using extensive kinetic, equilibrium, and thermodynamic studies. The best adsorption capacity was demonstrated by the tetracycline. Amoxicillin adsorption was also attempted, but it did not show positive results.

Use of Biochar from Rice Husk Pyrolysis: Part A: Recovery as an Adsorbent in the Removal of Emerging Compounds

One of the main products of pyrolysis is char. For the better performance and improvement of its physicochemical properties, it is necessary to make temperature changes. In this study, different temperatures have been tested for the pyrolysis of rice husk, and the biochar obtained from the process went through an evaluation to test its yield in the removal of emerging compounds such as azithromycin (AZT) and erythromycin (ERY). For this, pyrolysis of rice husk has been carried out at temperatures of 450, 500, 550, and 600 °C, and the biochars have been characterized by ultimate analysis and proximate analysis, as well as specific surface area tests. Then, different adsorption tests have been carried out with a 200 mg L^-1 drug (AZT and ERY) solution prepared in the laboratory. All biochars have been found to present removal percentages higher than 95%. Therefore, obtaining biochar from rice husk at any temperature and using it in the removal of high-molecular-weight compounds are quite suitable.

Critical review on adsorptive removal of antibiotics: Present situation, challenges and future perspective

This review gives a proper dedicated understanding of the contamination level, sources, and biological dangers related with different classes of antibiotics in consumable water. The literature on the adsorption of antibiotics is relatively uncommon and developments are still under progression, especially for adsorbents other than activated carbon. Also, adsorption technique has already been applied vastly for water treatment. Notwithstanding significant progressions, designed natural wastewater treatment frameworks are just bearably effective (48-77%) in the expulsion of antibiotics. Hence, the compilation of available literature especially for antibiotic adsorption was much needed. Moreover, the conventional adsorbents have some limitations of their own. In this study, the main focus was laid on unconventional adsorbents such as Biochar, Biopolymers, Carbon Nanotubes, Clays, Metal-Organic Frameworks, Microalgae and some miscellaneous adsorbents. The mechanism of adsorption by the unconventional adsorbents includes electrostatic interactions, π-π bonding, weak Van der Waal forces, H-bonding and surface complexation, which was similar to that of conventional adsorbents and hence these unconventional adsorbents can easily replace the costlier conventional adsorbents with even better adsorption efficiency. This paper also briefly discussed the thermodynamics, adsorption equilibrium; isotherm and kinetics of adsorption. This review paper seizes the critical advances of adsorption phenomenon at various interfaces and lays the foundation for current scenario associated with further progress. Besides, this study would help in understanding the antibiotic adsorption, cost estimation and future goals that will attract the young the researchers of this field.

Amelioration of adsorptive efficacy by synergistic assemblage of functionalized graphene oxide with esterified cellulose nanofibers for mitigation of pharmaceutical waste

An effort has been undertaken for valorization of surplus biomass to synthesize sustainable and commercially competitive nanoadsorbents utilizing green synthetic strategies. This study encompasses a pioneering research on the comparative adsorption analysis of different modified forms of graphene oxide (GO) combined with functionalized cellulose nanofibers (CNF) derived from surplus biomass for elimination of noxious drug species from aqueous environment with a comprehensive study for evaluating the effect of loading percentage of functionalized GO. Characteristic assessments of the prepared nanocomposites were performed using FT-IR studies, powder XRD studies, FESEM analysis, EDS analysis and BET studies. The prepared nanohybrids were evaluated for their adsorptive performance for elimination of ciprofloxacin and ofloxacin and their performance was optimized in terms of adsorbent loading, pH and initial drug concentration. Further, investigation of adsorbent properties and the adsorption process was undertaken by studying different kinetic and isotherm models of adsorption. The adsorption potential of functionalized CNF was substantially ameliorated through its facile assemblage with functionalized GO. The experimental outcomes revealed that 20 wt% loading of carboxylated graphene oxide within the perforated surface of esterified cellulose nanofibres exhibited best adsorption performance with maximum removal capacity of 45.04 mg g^-1 and 85.30 mg g^-1 for ciprofloxacin and ofloxacin, respectively. The outstanding regenerability and reusability of nanocomposites present tremendous potential for development of inexpensive and sustainable sorbent materials for managing pharmaceutical pollution. Literature presents scarce data and insufficient number of reports which thoroughly compares the role of differently functionalized GO to potentiate the adsorptive performance of biomass based nanocellulose and its broad application prospects in wastewater remediation. This marks the novelty of the present investigation.

Elimination of amoxicillin using zeolite Y-sea salt as a good catalyst for activation of hydrogen peroxide: Investigating degradation pathway and the effect of wastewater chemistry

The sea contains elements that can play a useful role in catalyzing reactions. Therefore, this research was done to focus on eliminating amoxicillin (AMX) from wastewater utilizing zeolite Y- sea salt catalyst in the presence of H₂O₂. The influences of furnace temperature (200-500 °C) and time duration in the furnace (1-4 h) were optimized during catalyst generation. Also, the effects of different parameters on AMX removal, such as pH (5.0-9.0), catalyst dose (0-10 g.L^-1), AMX concentration (50-300 mg.L^-1), contact time (10-130 min), and H₂O₂ concentration (0-6 mL/100 mL distilled water) were investigated. Different analyses like Brunauer-Emmett-Teller (BET), Fourier transform infrared (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA) were conducted to reveal catalyst properties. The BET-specific surface area of the catalyst (12.69 m²g^-1) insignificantly (p-value > 0.05) changed after AMX removal (13.04 m²g^-1), indicating the strength of the prepared catalyst. The active groups of N-H, O-H-O, O-Si-O, C-H, Si-O-Si, and Si-O-Al were determined in the catalyst structure. The highest removal of AMX (93%) was achieved in the zeolite-sea salt/H₂O₂ system at a pH level of 6.0 and an H₂O₂ concentration of 0.1 mL/100 mL. Elimination of the AMX followed pseudo-first-order kinetics. The catalyst was reclaimed up to 7 times and the removal efficiency was suitable up to the fifth stage. The by-products and reaction pathways were investigated by gas chromatography-mass spectrometry (GC-MS). The results showed that zeolite-sea salt can be utilized as an H₂O₂ activator for the effective degradation of AMX from wastewater.

Co-Cu oxide nano-flake adsorbent for tetracycline removal from aqueous solution

In this study, a new adsorbent based on Co-Cu oxide nano-flakes was investigated to remove tetracycline from aqueous systems. Ultrasonic-assisted co-precipitation method has been used to synthesize the adsorbent nanoparticles with different precursor concentration of Cu²⁺/Co²⁺. The properties of the adsorbents have been investigated using BET, FESEM/EDS, XRD, and FTIR techniques. The removal experiment results show that the maximum tetracycline adsorption (q_max=195mg·gr^-1) was obtained for the adsorbent synthesized by Cu²⁺:Co²⁺ molar ratio of 1:5. The adsorbent nanoparticles have a Co₃O₄ spinel crystal structure and a flake-shape morphology with thickness of 20 nm. Incorporation of copper atoms in the spinel structure was confirmed by XRD and FTIR results and hence, effectively promotes the removal of the tetracycline. The effect of various parameters such as adsorbent weight, pH, and time on the kinetics of adsorption was investigated. The results showed that the Langmuir isotherm was in better agreement with the experimental data of tetracycline adsorption. The overall rate of adsorption follows the first-order kinetic model, although the results of intraparticle diffusion model showed that diffusion mechanism is one of the controlling steps during the adsorption process.

Chitosan as additive affects the bacterial community, accelerates the removals of antibiotics and related resistance genes during chicken manure composting

Manures, storages for antibiotic resistance genes (ARGs), pollute soil and water as well as endanger human health. Recently, we have been searching a better solution to remove antibiotics and ARGs during aerobic composting. Here, the dynamics of chitosan addition on the profiles of 71 ARGs, bacterial communities, chlortetracycline (CTC), ofloxacin (OFX) were investigated in chicken manure composting and compared with zeolite addition. Chitosan addition effectively reduces antibiotics contents (CTC under detection limit, OFX 90.96%), amounts (18) and abundance (56.7%, 11.1% higher than zeolite addition) of ARGs and mobile genetic elements (MGEs) after 42 days composting. Network analysis indicated that a total of 27 genera strains assigned into 4 phyla (Firmicutes, Proteobacteria, Actinobacteria and Bacteroidetes) were the potential hosts of ARGs. Redundancy analysis (RDA) demonstrated that bacterial community succession is the main contributor in the variation of ARGs. Overall, chitosan addition may effect bacterial composition by influencing physic-chemical properties and the concentration of antibiotics, Cu²⁺, Zn²⁺ to reduce the risk of ARG transmission. This study gives a new strategy about antibiotics and ARGs removal from composting on the basis of previous studies.

Mechanistic interaction of ciprofloxacin on zeolite modified seaweed (Sargassum crassifolium) derived biochar: Kinetics, isotherm and thermodynamics

Modification of biochar for efficient removal of antibiotics from water could be a valuable approach in the environmental applications. In this study, a brown seaweed (Sargassum crassifolium) was pyrolyzed at 500 °C and the obtained biochar (SWBC) was modified with zeolite through the slurry method maintaining the ratio at 1:5 (zeolite: biochar) (SWBC-Z). Batch adsorption experiments were conducted to evaluate the adsorption tendency of SWBC and SWBC-Z for the removal of ciprofloxacin (CPX) from water via pH edge, kinetics, isotherm and thermodynamic experiments. The highest adsorption was in the pH range of 6.5-8, supported by the electrostatic attractions and hydrogen bonding with zwitterionic CPX. Experimental kinetics data was well-fitted to the pseudo-second-order and Elovich models (R2 of 0.992 and 0.976, respectively), while the Langmuir and Freundlich isotherm models best described the isotherm data (R2 of 0.954 and 0.976, respectively). The maximum adsorption capacity of 93.65 mg g-1 was recorded for the SWBC-Z. The models predicted chemisorption and physisorption interactions on the heterogenous biochar surface. Well-defined peaks of silanol groups in the FTIR spectrum of SWBC-Z and its electron microscopy confirmed the incorporation of zeolite minerals. Post adsorption FTIR analysis elucidated the changes in the surface functional groups of the SWBC-Z. Thermodynamic data revealed spontaneous and exothermic reaction between CPX and both the biochars. It was concluded that modification of pristine biochar with zeolite imparted greater surface area and additional active sites, which subsequently enhanced the overall CPX adsorption by the SWBC-Z.

Response surface methodology optimizing the adsorptive removal of azithromycin using mesoporous silica SBA-15: Mechanism, thermodynamic, equilibrium, and kinetics modeling studies

The objective of this research was to study an effective adsorbent for removing azithromycin (AZT) from industrial wastewater. AZT is an antibiotic used for many diseases remedy, but it is a pollutant to our environment; therefore, its residual should be removed from wastewater. The mesoporous SBA-15 silica as an efficient adsorbent was prepared by the hydrothermal method. The surface of mesoporous SBA-15 plays a significant role in the removal process; therefore, the characterization of the adsorbent was accomplished by several techniques. The batch system has been used, and the effect of four essential variables: pH (3-10), drug concentration (20-200 mg L^-1), sorbent weight (0.2-2 g L^-1), and temperature (20-40 °C) were investigated on the AZT removal efficiency by response surface methodology (RSM). The isotherm results were found to be in proper compliance with the isotherm model of Freundlich. In the kinetics part of this study, the experimental outcomes were fitted to the equation model of pseudo-second-order. The calculation of thermodynamic parameters shows that the removal process is spontaneous and endothermic. Upon the results, the vast surface area, the active functional groups, reusability, stability, and inexpensively make the mesoporous SBA-15 a suitable candidate for removal of AZT and similar antibiotics.

Au-O-MWCNTs and TiO2-O-MWCNTs as Efficient Nanocarriers for Dexamethasone: Adsorption Isotherms and Kinetic Studies

In this research, the fabrication of drug delivery systems based on oxidized multiwall carbon nanotubes (O-MWCNTs) was studied. Herein, TiO2 and Au were conjugated with O-MWCNTs to prepare efficient nanocarriers for dexamethasone (dex). The samples were characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and X-ray diffraction (XRD). In addition, dex loading was studied using adsorption isotherms including Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich. The results show that dex adsorption agreed well with the Freundlich isotherm. Increasing the TiO2 to O-MWCNT ratio from (1 : 4) to (1 : 2) can improve the adsorption capacity from $290\text{mg}\cdot {\text{g}}^{-1}$ to 320 $320\text{mg}\cdot {\text{g}}^{-1}$ . The increasing Au amount increases the adsorption capacity from $437.78\text{mg}\cdot {\text{g}}^{-1}$ (SA1) to maximum $476.19\text{mg}\cdot {\text{g}}^{-1}$ (SA6). The maximum equilibrium binding energy $A_T$ $\left(1.67\text{L}\cdot {\text{mg}}^{-1}\right)$ was obtained for SA2, and SA7 shows high binding strength between dex and the nanoadsorbent. Carbon nanotubes (CNTs) show good affinity with high loading capabilities for dexamethasone adsorption. The synthesized TiO2-O-MWCNTs:1/2 with the maximum removal percent (80%) was proposed as an appropriate nanocarrier for dexamethasone. Pseudo-first order, pseudo-second order, Elovich, and intraparticle diffusion models were investigated for all synthesized drug nanocarriers. According to regression coefficients, experimental data are in good agreement with the pseudo-second order model for all adsorbents except O-MWCNT/CTAB. Experimental results revealed that the Elovich model could account for the O-MWCNT/CTAB adsorbent.

Adsorptive removal of antibiotic ofloxacin in aqueous phase using rGO-MoS2 heterostructure

This paper reports the synthesis, characterization and detailed adsorption studies of rGO-MoS₂ heterostructure. The heterostructure was explored for the adsorption of ofloxacin from the aqueous phase. Detailed studies were conducted to study the effect of crucial parameters such as pH of drug solution, adsorbent dose, temperature and initial drug concentration on the adsorption capacity. Even with a low surface area of 17.17 m²/g, the adsorbent exhibited maximum removal efficiency of 95% at a dose of 0.35 g/L and an initial drug concentration of 10 mg/L in 240 min. Thermodynamic study revealed the values for ∆H⁰ and ∆G⁰ to be - 101.15 and - 7.47 kJ/mol respectively, indicating that the process is spontaneous and exothermic in nature. The heterostructure adsorbent exhibited remarkable reusability and stability up to five cycles. The heterostructure combines excellent adsorption capabilities arising from the two-dimensional structures of rGO and MoS₂ with the stronger and more specific interaction with the drug molecules which results in better performance towards the removal of the drug. The excellent performance of the heterostructure indicates that combining 2D materials can be a good strategy for producing highly efficient materials towards the adsorptive removal of pollutants.

A Review on the Application of Zeolites and Mesoporous Silica Materials in the Removal of Non-Steroidal Anti-Inflammatory Drugs and Antibiotics from Water

Zeolites and mesoporous silica materials are effective adsorbents that can be useful for the removal of various pharmaceuticals including non-steroidal anti-inflammatory drugs and antibiotics from low-quality water. This paper summarizes the properties and basic characteristics of zeolites and mesoporous silica materials and reviews the recent studies on the efficacy of the adsorption of selected non-steroidal medicinal products and antibiotics by these adsorbents to assess the potential opportunities and challenges of using them in water treatment. It was found that the adsorption capacity of sorbents with high silica content is related to their surface hydrophobicity (hydrophilicity) and structural features, such as micropore volume and pore size, as well as the properties of the studied medicinal products. This review can be of help to scientists to develop an effective strategy for reducing the amount of these two groups of pharmaceuticals in wastewater.

A critical review on environmental presence of pharmaceutical drugs tested for the covid-19 treatment

On March 11, 2020, the World Health Organization (WHO) declared COVID-19 a pandemic. The outbreak caused a worldwide impact, becoming a health threat to the general population and its professionals. To date, there are no specific antiviral treatments or vaccines for the COVID-19 infection, however, some drugs are being clinically tested. The use of these drugs on large scale raises great concern about their imminent environmental risk, since the elimination of these compounds by feces and urine associated with the inefficiency of sewage treatment plants in their removal can result in their persistence in the environment, putting in risk the health of humans and of other species. Thus, the goal of this work was to conduct a review of other studies that evaluated the presence of the drugs chloroquine, hydroxychloroquine, azithromycin, ivermectin, dexamethasone, remdesivir, favipiravir and some HIV antivirals in the environment. The research indicated the presence of these drugs in the environment in different regions, with concentration data that could serve as a basis for further comparative studies following the pandemic.

Degradation of ofloxacin by a manganese-oxidizing bacterium Pseudomonas sp. F2 and its biogenic manganese oxides

Fluoroquinolone antibiotics like ofloxacin (OFL) have been frequently detected in the aquatic environment. Recently manganese-oxidizing bacteria (MOB) have attracted research efforts on the degradation of recalcitrant pollutants with the aid of their biogenic manganese oxides (BioMnOx). Herein, the degradation of OFL with a strain of MOB (Pseudomonas sp. F2) was investigated for the first time. It was found that the bacteria can degrade up to 100% of 5 μg/L OFL. BioMnOx and Mn(III) intermediates significantly contributed to the degradation. Moreover, the degradation was clearly declined when the microbial activity was inactivated by heat or ethanol, indicating the importance of bioactivity. Possible transformation products of OFL were identified by HPLC-MS and the degradation pathway was proposed. In addition, the toxicity of OFL was reduced by 66% after the degradation.

Potential interactions between an oral fosfomycin formulation and feed or drinking water: Impact on bioavailability in piglets

Feed and drinking water are the most frequently used vehicles for administration of antibiotics in intensive pig production. Interactions of drugs with feed and water components may affect dissolution and bioavailability. Therefore, antibiotic formulations should be tested in order to assure their suitability for oral use. In this study, an oral fosfomycin (FOS) formulation was evaluated considering dissolution in water (soft and hard), release kinetics from feed in simulated gastrointestinal fluids and bioavailability after oral administration blended into feed or dissolved in water (soft and hard), to fed and fasted piglets. FOS reached immediate dissolution in soft and hard water. The presence of feed significantly decreased antibiotic dissolution in simulated intestinal medium. Bioavailability was lower when feed was used as a vehicle for FOS administration than when the drug was dissolved in water (soft or hard). The fed or fasted condition of piglets did not affect bioavailability. Probably, FOS interactions with feed components alter its dissolution in the gastrointestinal tract, and only a fraction of the dose would be available for absorption. This information must be considered to support decisions on eligibility of antibiotic pharmaceutical formulations and the vehicle for their administration in order to pursue a responsible use of antibiotics.

Enhanced removal of pefloxacin from aqueous solution by adsorption and Fenton-like oxidation using NH2-MIL-88B

While Fe-based metal-organic frameworks (MOFs) can be used to remove antibiotics by adsorption, knowledge of how antibiotics are degraded by MOFs is still limited. In this study, one Fe-based MOF, NH₂-MIL-88B was used to remove pefloxacin from aqueous solution via a combination of adsorption and Fenton-like oxidation. NH₂-MIL-88B exhibited a high adsorption capacity for pefloxacin (41.37 mg·g^-1), with >99% removal efficiency within 120 min based on Fenton-like oxidation. To better understand the mechanisms involved in integrated adsorption and Fenton-like oxidation, various advanced characterization techniques were used to monitor the changes in morphology and composition of NH_2-MIL-88B before and after removal of pefloxacin. Scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) all supported adsorption and Fenton oxidation of pefloxacin. In addition, the pefloxacin degradation products identified by LC-UV and LC-MS provided information on the potential adsorption-Fenton oxidation mechanism. These results suggested that NH₂-MIL-88B has remarkably potential to be used in an integrated adsorption and Fenton-like process for the removal of antibiotics from aqueous solution.

Simultaneous removal of ammonium ions and sulfamethoxazole by ozone regenerated high silica zeolites

Continuous development of industry and civilization has led to changes in composition, texture and toxicity of waste water due to the wide range of pollutants being present. Considering that the conventional wastewater treatment methods are insufficient for removing micropollutants and nutrients to a high level, other, alternative, treatment methods should be used to polish wastewater treatment plant effluents. In this study we developed an alternative, polishing concept for removal of ammonium and micropollutants that could potentially be incorporated in existing wastewater treatment plants. We demonstrated a method to use high silica MOR zeolite granules as an adsorbent for simultaneous removal of the micropollutant sulfamethoxazole (SMX) and ammonium (NH₄⁺) ions from aqueous solutions. At an initial NH₄⁺ concentration of 10 mg/L the high silica zeolite mordenite (MOR) granules removed 0.42 mg/g of NH₄⁺, similar to the removal obtained by commonly used natural zeolite Zeolita (0.44 mg/g). However, at higher NH₄⁺ concentrations the Zeolita performed better. In addition, the Langmuir isotherm model showed a higher maximum adsorption capacity of Zeolita (q_max, 4.08 mg/g), which was about two times higher than that of MOR (2.11). The adsorption capacity of MOR towards SMX, at both low (2 µg/L) and high (50 mg/L) initial concentrations, was high and even increased in the presence of NH₄⁺ ions. The used adsorbent could be regenerated with ozone and reused in consecutive adsorption-regeneration cycles with marginal decrease in the total adsorption capacity.

Study of Faujasite zeolite as a modified delivery carrier for isoniazid

The adsorption of isoniazid in the Faujasite zeolite channels has been studied. For that, the influence of the pH from the solution media in the adsorption process was verified to enable higher amount of isoniazid retained. With the information of the best pH and the equilibrium time obtained with the kinetic study, an isotherm was constructed and the hybrid material obtained with the plateau concentration equilibrium was characterized with several techniques. Molecular modeling calculations were also performed for a better understanding of the adsorption process and how the interaction between zeolite and isoniazid occurs. The geometrical disposition of the drug molecules into the zeolite channels, the saturation levels, the different isoniazid protonation states with respect to the pH media and the interaction energy between the zeolite surface and the isoniazid molecule was studied. Finally, a drug release study was made to verify if the Faujasite-Y zeolite could change the isoniazid release in acid and phosphate buffer media. The results show that the Faujasite-Y has the possibility to work as carrier for isoniazid, where the adsorption process is more effective in media at pH 3, result confirmed by the molecular modeling. The isoniazid release essay showed that the hybrid material does not change the drug release profile, provides more stability in acid media, indicating that the zeolite can be used as carrier for isoniazid, and improve the medicine formulations on antituberculosis treatment.

Application of Fourier transform ion cyclotron resonance mass spectrometry to characterize natural organic matter

Advances in the ultra-high-resolution mass spectroscopy lead to a deep insight into the molecular characterization of natural organic matter (NOM). Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) has been used as one of the most powerful tools to decipher NOM molecules. In FTICR-MS analysis, the matrix effects caused by the co-occurring inorganic substances in water samples greatly affect the ionization of NOM molecules. The inherent complexity of NOM may hinder its component classification and formula assignment. In this study, basic principles and recent advances for sample separation and purification approaches, ionization methods, and the evolutions in formula assignment and data exploitation of the FTICR-MS analysis were reviewed. The complementary characterization methods for FTICR-MS were also reviewed. By coupling with other developed/developing characterization methods, the statistical confidence for inferring the NOM compositions by FTICR-MS was greatly improved. Despite that the refined separation procedures and advanced data processing methods for NOM molecules have been exploited, the big challenge for interpreting NOM molecules is to give the basic structures of them. Online share of the FTICR-MS data, further optimizing the FTICR-MS technique, and coupling this technique with more characterization methods would be beneficial to improving the understanding of the composition and property of NOM.

Adsorption isotherm models: Classification, physical meaning, application and solving method

Adsorption is widely applied separation process, especially in environmental remediation, due to its low cost and high efficiency. Adsorption isotherm models can provide mechanism information of the adsorption process, which is important for the design of adsorption system. However, the classification, physical meaning, application and solving method of the isotherms have not been systematical analyzed and summarized. In this paper, the adsorption isotherms were classified into adsorption empirical isotherms, isotherms based on Polanyi's theory, chemical adsorption isotherms, physical adsorption isotherms, and the ion exchange model. The derivation and physical meaning of the isotherm models were discussed in detail. In addition, the application of the isotherm models were analyzed and summarized based on over 200 adsorption equilibrium data in literature. The statistical parameters for evaluating the fitness of the models were also discussed. Finally, a user interface (UI) was developed based on Excel software for solving the isotherm models, which was provided in supplemental material and can be easily used to model the adsorption equilibrium data. This paper will provide theoretical basis and guiding methodology for the selection and use of the adsorption isotherms.

Fe3O4-Zeolite Hybrid Material as Hetero-Fenton Catalyst for Enhanced Degradation of Aqueous Ofloxacin Solution

A hetero-Fenton catalyst comprising of Fe3O4 nanoparticles loaded on zeolite (FeZ) has been synthesized using a facile co-precipitation method. The catalyst was characterized using various characterization methods and then, subsequently, was used to degrade ofloxacin (OFL, 20 mg·L−1), an antibiotic, via a heterogeneous Fenton process in the presence of an oxidizing agent. The effects of different parameters such as Fe3O4 loading on zeolite, catalyst loading, initial solution pH, initial OFL concentration, different oxidants, H2O2 dosage, reaction temperature, and inorganic salts were studied to determine the performance of the FeZ catalyst towards Fenton degradation of OFL under different conditions. Experimental results revealed that as much as 88% OFL and 51.2% total organic carbon (TOC) could be removed in 120 min using the FeZ catalyst. Moreover, the FeZ composite catalyst showed good stability for Fenton degradation of OFL even after five cycles, indicating that the FeZ catalyst could be a good candidate for wastewater remediation.