Adsorption and regeneration on iron-activated biochar for removal of microcystin-LR

Modification of sand filtration system with biochar/zero valent iron-biochar for the simultaneous removal of algal cells and microcystin-LR

High-density algal cells and the released algal toxins during harmful algal blooms cannot be effectively removed by traditional sand filtration systems. In this study, bare sand filtration columns were modified by different mass ratios of biochar (synthesized at different pyrolysis temperatures) and used to simultaneously capture algal cells and microcystins from water. We found that the addition of 2 wt% biochar synthesized at 700℃ could effectively remove Microcystis aeruginosa and Chlorella vulgaris cells under both slow and fast filtration flow conditions, and remove the released microcystin-LR in suspension. Effective removal performance with the coexistence of natural organic matters, in real water samples, during 3 transport-elution cycles and continuous operation for 50 pore volumes was also achieved by biochar-modified filtration system. The high algal adsorption capacity due to the wrinkled structure and the less negative charge of biochar contributed to the enhanced removal performance. Moreover, using zero valent iron (ZVI) loaded biochar to modify sand columns would effectively inactivate and inhibit the regrowth of retained algal cells. The results showed that as one type of inexpensive and readily available bio-materials, biochar/ZVI-biochar could be used to modify the sand filtration system for the effective removal of algal cells and toxins from water.

Rice Straw-Derived Biochar Mitigates Microcystin-LR-Induced Hepatic Histopathological Injury and Oxidative Damage in Male Zebrafish via the Nrf2 Signaling Pathway

Microcystin-leucine arginine (MC-LR) poses a serious threat to aquatic animals during cyanobacterial blooms. Recently, biochar (BC), derived from rice straw, has emerged as a potent adsorbent for eliminating hazardous contaminants from water. To assess the joint hepatotoxic effects of environmentally relevant concentrations of MC-LR and BC on fish, male adult zebrafish (Danio rerio) were sub-chronically co-exposed to varying concentrations of MC-LR (0, 1, 5, and 25 μg/L) and BC (0 and 100 μg/L) in a fully factorial experiment. After 30 days exposure, our findings suggested that the existence of BC significantly decreased MC-LR bioavailability in liver. Furthermore, histopathological analysis revealed that BC mitigated MC-LR-induced hepatic lesions, which were characterized by mild damage, such as vacuolization, pyknotic nuclei, and swollen mitochondria. Compared to the groups exposed solely to MC-LR, decreased malondialdehyde (MDA) and increased catalase (CAT) and superoxide dismutase (SOD) were noticed in the mixture groups. Concurrently, significant changes in the mRNA expression levels of Nrf2 pathway genes (cat, sod1, gstr, keap1a, nrf2a, and gclc) further proved that BC reduces the oxidative damage induced by MC-LR. These findings demonstrate that BC decreases MC-LR bioavailability in the liver, thereby alleviating MC-LR-induced hepatotoxicity through the Nrf2 signaling pathway in zebrafish. Our results also imply that BC could serve as a potentially environmentally friendly material for mitigating the detrimental effects of MC-LR on fish.

Magnetic nanostructured agents for the mitigation of mycotoxins and cyanotoxins in the food chain

Natural toxins, such as mycotoxins and cyanotoxins, can contaminate food and feed, leading to toxicity in humans and animals. This study focused on using nine magnetic nanostructured agents to remove the main types of toxins. Initially, the efficacy of these materials was evaluated in water solutions, revealing that composites with sizes below 3 mm, containing magnetite, activated carbon, esterified pectin, and sodium alginate, removed up to 90% of mycotoxins and cyanotoxins with an adsorption of 873 ng/g. The application of the nanostructures was then assessed in beer, milk, Distillers Dried Grains with Solubles and water contaminated with cyanobacteria. The presence of matrix slightly decreases the adsorption capacity for some toxins. The maximum toxin removal capacity was calculated with cyanotoxins, composites achieved a removal of up to 0.12 mg/g, while nanocomposites (15 μm) reached 36.6 mg/g. Therefore, these findings point out the potential for using nanotechnology in addressing natural toxins contamination.

Insight into the performance and microbial community of anaerobic digestion treating cow manure with a novel iron-functionalized activated biochar

The main objective of this research was to evaluate the impacts of FeCl3-activated biochar (FA-BC) on anaerobic digestion (AD) treating cow manure. The study focused on improving AD performance and understanding microbial community structure with the addition of FA-BC, while comparing FA-BC with other conductive additives, such as pristine biochar (P-BC), NaOH-activated biochar (NA-BC), and magnetite. Key findings indicated that FA- BC significantly enhanced the AD performance, supported by an increase in CH4 yield of 11-16% and a reduction in the lag phase by 51%. The high surface area and electrical conductivity of FA-BC synergistically facilitated direct interspecies electron transfer (DIET), leading to these improvements. On contrast, P-BC and NA-BC were not efficient in enhancing the AD performance due to relatively low electrical conductivity. P-BC also improved the CH4 yield, but less effectively than FA-BC. The effects of NA-BC varied with its dosage, showing inhibition at higher dosages due to excessive surface area. Magnetite, despite its high conductivity, made the limited enhancement in CH4 yield owing to its low surface area. Additionally, the statistical analyses revealed that each additive differently affected specific bacterial and archaeal groups depending on their physical and chemical properties. Thus, these findings suggest that FA-BC would be a highly promising additive for enhan cing AD systems, with potential applications in waste management and renewable energy production.

Comparative study of organic removal by pre-adsorption oxidation and synchronous adsorption oxidation processes: Performance and mechanism

Both adsorption and oxidation occur and contribute to organics removal in carbonaceous materials based advanced oxidation processes, while the correction of adsorption and oxidation, and the role of adsorption in the veritable removal of organic are not clear. Herein, we investigated the performance of carbamazepine (CBZ) removal by peroxymonosulfate (PMS) activated by magnetic Fe-doped biochar through two models of pre-adsorption oxidation and synchronous adsorption oxidation processes. The adsorption process was better fitted by pseudo-second-order kinetic model and the adsorption mechanism was obtained by comprehensive analysis of equilibrium adsorption capacities, surface functional groups, specific surface area, pore volume, and ID/IG value. It is noted that pre-adsorption highly inhibited the further oxidation of CBZ in 0.5Fe@LSBC700/PMS system due to the occupied catalytic active sites. Total CBZ removal in pre-adsorption oxidation (45 %) was inferior to synchronous adsorption oxidation (∼100 %), as well as the veritable CBZ oxidation removal of 27 % for pre-adsorption oxidation vs ∼100 % in synchronous adsorption oxidation at 30 min. Oxidation degradation of CBZ based on radical oxidation was identified by quenching experiments and electron paramagnetic resonance measurements. This work is conducive to identifying the role of adsorption during the removal of organics in the adsorption-oxidation process, as well as veritable adsorption and oxidation removal of organics.

Comprehensive strategies for microcystin degradation: A review of the physical, chemical, and biological methods and genetic engineering

Addressing the threat of harmful cyanobacterial blooms (CyanoHABs) and their associated microcystins (MCs) is crucial for global drinking water safety. In this review, we comprehensively analyze and compares the physical, chemical, and biological methods and genetic engineering for MCs degradation in aquatic environments. Physical methods, such as UV treatments and photocatalytic reactions, have a high efficiency in breaking down MCs, with the potential for further enhancement in performance and reduction of hazardous byproducts. Chemical treatments using chlorine dioxide and potassium permanganate can reduce MC levels but require careful dosage management to avoid toxic by-products and protect aquatic ecosystems. Biological methods, including microbial degradation and phytoremediation techniques, show promise for the biodegradation of MCs, offering reduced environmental impact and increased sustainability. Genetic engineering, such as immobilization of microcystinase A (MlrA) in Escherichia coli and its expression in Synechocystis sp., has proven effective in decomposing MCs such as MC-LR. However, challenges related to specific environmental conditions such as temperature variations, pH levels, presence of other contaminants, nutrient availability, oxygen levels, and light exposure, as well as scalability of biological systems, necessitate further exploration. We provide a comprehensive evaluation of MCs degradation techniques, delving into their practicality, assessing the environmental impacts, and scrutinizing their efficiency to offer crucial insights into the multifaceted nature of these methods in various environmental contexts. The integration of various methodologies to enhance degradation efficiency is vital in the field of water safety, underscoring the need for ongoing innovation.

Effective removal of microplastics by filamentous algae and its magnetic biochar: Performance and mechanism

In recent years, filamentous algae blooms and microplastics (MPs) pollution have become two major ecological and environmental problems in urban water systems. In order to solve these two problems at the same time, this study explored the loading capacity of MPs on fresh filamentous algae, and successfully synthesized magnetic filamentous algae biochar loading with Fe3O4 by hydrothermal method, with the purpose of removing MPs from water. The magnetic filamentous algal biochar was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and so on. Experiments on adsorption kinetics, adsorption isotherms and optimum pH were carried out to explore the adsorption mechanism of MPs on magnetic filamentous algal biochar. The adsorption kinetics and adsorption isotherm models were evaluated, and the selection criterion for the appropriate model was determined by using the residual sum of squares (RSS) and Bayesian information criterion (BIC). Microscope images revealed that fresh filamentous algae could interact with MPs in the form of entanglement, adhesion and encapsulation. The average load of MPs in filamentous algae samples was 14.1 ± 5 items/g dry weight. The theoretical maximum adsorption capacities of polystyrene MPs (PS-MPs) by raw biochar (A500) and magnetic biochar with Fe3O4 (M2A500) were 176.99 mg/g and 215.58 mg/g, respectively. The adsorbent materials gave better reusability because they could be reused up to five times. Overall, these findings have provided new insights into the use of filamentous algae for in situ remediation of fluvial MPs pollution, as well as feasible strategies for the recycling of algal waste.

Coupling physiochemical adsorption with biodegradation for enhanced removal of microcystin-LR in water

To innovate the design of water treatment technology for algal toxin removal, this research investigated the mechanisms of cyanotoxin microcystin-LR (MC-LR) removal by a coupled adsorption-biodegradation. Eight types of woody carbonaceous adsorbents with and without Sphingopyxis sp. m6, a MC-LR degrading bacterium, were tested for MC-LR removal in water. All adsorbents showed good adsorption capability, removing 40 % to almost 100 % of the MC-LR (4.5 mg/L) within 48 h in batch experiments. Adding Sphingopyxis sp. m6 continuously promoted MC-LR biological removal, and successfully broke the barrier of adsorption capacity of tested adsorbents, removing >90 % of the MC-LR in most of the coupled adsorption-biodegradation tests, especially for those adsorbents had low physiochemical adsorption capacity. Variance partitioning analysis indicated that mesopore was the dominant contributor to adsorption capacity of MC-LR in pure adsorption treatments, which acted synergistically with electrical conductivity, polarity and total functional groups on the absorbent. Pore structure was the key factor beneficial for the growth of Sphingopyxis sp. m6 (51% contribution) and subsequent MC-LR biological removal rate (80 % contribution). Overall, pinewood-based carbonaceous adsorbents (especially pinewood activated carbon) exhibited the highest adsorption capacity towards MC-LR and provided the most favorable conditions for biological removal of MC-LR, largely because of their high mesopore volume, total functional groups and electric conductivity. The research outcomes not only deepened the quantitative understanding of mechanisms for MC-LR removal by the coupled process, but also provided theoretical basis for future materials' selection and modification during the practical application of coupled process.

Influence of biochar on the removal of Microcystin-LR and Saxitoxin from aqueous solutions

The present study assessed the effective use of biochar for the adsorption of two potent HAB toxins namely, Microcystin-LR (MCLR) and Saxitoxin (STX) through a combination of dosage, kinetic, equilibrium, initial pH, and competitive adsorption experiments. The adsorption results suggest that biochar has excellent capabilities for removing MCLR and STX, with STX reporting higher adsorption capacities (622.53-3507.46 µg/g). STX removal required a minimal dosage of 0.02 g/L, while MCLR removal needed 0.4 g/L for > 90%. Similarly, a shorter contact time was required for STX removal compared to MCLR for > 90% of toxin removed from water. Initial pH study revealed that for MCLR acidic conditions favored higher uptake while STX favored basic conditions. Kinetic studies revealed that the Elovich model to be most suitable for both toxins, while STX also showed suitable fittings for Pseudo-First Order and Pseudo-Second Order in individual toxin systems. Similarly, for the Elovich model the most suited kinetic model for both toxins in presence of each other. Isotherm studies confirmed the Langmuir-Freundlich model as the best fit for both toxins. These results suggest adsorption mechanisms including pore filling, hydrogen bonding, π-π interactions, hydrophobic interactions, electrostatic attraction, and dispersive interactions.

Physico-chemical treatments for the removal of cyanotoxins from drinking water: Current challenges and future trends

Cyanobacteria are highly prevalent blue-green algae that grow in stagnant and nutrient-rich water bodies. Environmental conditions, such as eutrophication and human activities, increased the cyanobacterial blooms in freshwater resources worldwide. The excessive bloom formation has also resulted in an alarming surge of cyanobacterial toxins. Prolonged exposure to cyanotoxins is a potential threat to natural ecosystems, animal and human health by the spoilage of the quality of bathing and drinking water. Various molecular and analytical methods have been proposed to monitor their occurrence and understand their global distribution. Moreover, different physical, chemical, and biological approaches have been employed to control cyanobacterial blooms and their toxins to mitigate their occurrence. Numerous strategies have been engaged in drinking water treatment plants (DWTPs). However, the degree of treatment varies greatly and is primarily determined by the source, water properties, and operating parameters such as temperature, pH, and cyanotoxin variants and levels. A comprehensive compilation of methods, from traditional approaches to more advanced oxidation processes (AOPs), are presented for the removal of intracellular and extracellular cyanotoxins. This review discusses the effectiveness of various physicochemical operations and their limitations in a DWTP, for the removal of various cyanotoxins. These operations span from simple to advanced treatment levels with varying degrees of effectiveness and differing costs of implementation. Furthermore, mitigation measures applied in other toxin systems have been considered as alternative strategies.

Integration of hydrothermal liquefaction of Cyanophyta and supercritical water oxidation of its aqueous phase products: Biocrude production and nutrient removal

Cyanophyta has the potential to produce biocrude via hydrothermal liquefaction (HTL). However, aqueous phase products (APs), as by-products of HTL, pose a risk of eutrophication for the high levels of carbon, nitrogen, and phosphorus. Supercritical water oxidation (SCWO) can efficiently convert organics into small molecules, offering a technique for the harmless treatment of APs. Effects of holding time, pressure, and moisture content on the biocrude yields from isothermal HTL (300 °C) and fast HTL (salt bath temperature of 500 °C) were comprehensively investigated. Biocrude properties were characterized by elemental analysis, FT-IR and GC-MS. Subsequently, the APs obtained under the conditions producing the highest biocrude yield were subjected to SCWO at 550 °C with different oxidation coefficients (n) from 0 to 2. Removal rates of chemical oxygen demand (COD), ammonia nitrogen (NH3-N), and total phosphorus (TP) were further explored. The results show that the highest biocrude yields from isothermal HTL and fast HTL were 24.2 wt% (300 °C, 1800 s, 25 MPa, and 80 wt% moisture content) and 21.9 wt% (500 °C, 40 s, 25 MPa, and 80 wt% moisture content), respectively. The biocrude primarily consisted of N-containing heterocyclic compounds, amides, and acids. SCWO effectively degraded the COD and TP in APs, while the NH3-N required further degradation. At n = 2, the highest removal rates of COD, NH3-N and TP were 98.5 %, 22.6 % and 89.1 %, respectively.

Magnetically recyclable Cu2+ doped Fe3O4@biochar for in-situ inactivation of Microcystis aeruginosa: Performance and reusability

Harmful cyanobacterial blooms in eutrophic water bodies have frequently occurred worldwide and become a major environmental concern. Therefore, it is imperative to develop a stable and efficient algaecide to solve this issue. In this study, our purpose was to investigate the efficacy and mechanism of a newly developed Cu2+ doped Fe3O4@Biochar magnetic composite (Cu-Mag-BC) in in-situ inactivation of Microcystis aeruginosa (M. aeruginosa). We successfully synthesized the Cu-Mag-BC by coating Cu2+ onto Fe3O4@Biochar. Cu-Mag-BC exhibited superparamagnetic behavior and was uniformly impregnated by Cu2+. Cu-Mag-BC (5 mg/L), rapidly inactivated chlorophyll-a (Chl-a) in M. aeruginosa with low Fe and Cu leaching, during which time the OD264 value and malondialdehyde (MDA) content increased, while the activities of superoxide dismutase (SOD) and catalase (CAT) first increased and then decreased, due to oxidative stress induced by over-generated reactive oxygen species (ROS). Quantitative results showed that ·O2- and ·OH were the main ROS species produced from Cu-Mag-BC. Inactivation efficiency was maintained at approximately 80 % after three consecutive runs and total Chl-a removal efficiency reached 2.84 g/g, indicating good reusability and stability. A possible inactivation mechanism is proposed; amino groups and adipose chain were the primary oxidation sites. Thus, Cu-Mag-BC shows potential as a candidate for simultaneously inactivating harmful cyanobacteria and preventing secondary pollution.

Combined effects of microcystin-LR and rice straw-derived biochar on the hepatic antioxidant capacity of zebrafish: Insights from LC-MS/MS-based metabolomics analysis

Microcystin-LR (MC-LR) produced by cyanobacteria blooms poses a serious risk to aquatic organisms. Rice straw-derived biochar (BC) is gradually being utilized as an effective adsorbent to remove water pollutants. In the present study, the combined toxicity of MC-LR and BC on hepatic antioxidant capacity and metabolic phenotype of zebrafish (Danio rerio) were conducted due to the increasing concern of eutrophication in aquatic environments. Female zebrafish were exposed to solutions of MC-LR (10 μg/L) and BC (100 μg/L) individually and in combination for 30 days. The results indicated that sub-chronic MC-LR exposure induced oxidative stress and metabolic disorders, with a significant elevation of several amino acids, glucose as well as unsaturated fatty acids. Metabolic pathway analysis showed that the ascorbate and aldarate metabolism and biosynthesis of unsaturated fatty acids were affected under MC-LR stress. Significantly increased MDA levels along with significantly decreased CAT and GPx activities were observed in the MC-LR group. Nevertheless, MDA levels, antioxidant enzyme activities, and the relevant gene expressions (cat1, nrf2a, HO-1, keap1a) returned to baseline in the co-exposure group. These findings revealed that MC-LR resulted in metabolic disorders of protein, sugar, and lipid related to energy production, and BC could relieve MC-LR-induced metabolic disorder and oxidative stress in the liver of zebrafish. However, the potential risk of BC-induced metabolic disorder should not be neglected. Our present results highlight the potential of BC as a tool for mitigating the negative impacts of MC-LR on aquatic organisms in blooms-contaminated water.

Turning waste avocado stones and montmorillonite into magnetite-supported nanocomposites for the depollution of methylene blue: adsorbent reusability and performance optimization

The existence of methylene blue (MB) in wastewater even as traces is raising environmental concerns. In this regard, the performances of four adsorbents, avocado stone biochar (AVS-BC), montmorillonite (MMT), and their magnetite Fe3O4-derived counterparts, were compared. Results showed the superior performance of Fe3O4@AVS-BC and Fe3O4@MMT nanocomposites with removal percentages (%R) of 95.59% and 88%. The morphological features of AVS-BC as revealed by SEM analysis showed a highly porous surface compared to a plane and smooth surface in the case of MMT. Surface analysis using FT-IR and Raman spectroscopies corroborated the existence of the Fe-O peaks upon loading with magnetite. The XRD analysis confirmed the formation of cubic magnetite nanoparticles. The adsorption process in the batch mode was optimized using central composite design (CCD). Equilibrium and kinetic isotherms showed that the adsorption of MB onto Fe3O4@AVS-BC fitted well with the Langmuir isotherm and the pseudo-second-order (PSO) model. The maximum adsorption capacity (qm) was 118.9 mg/g (Fe3O4@AVS-BC) and 72.39 mg/g (Fe3O4@MMT). The Fe3O4@AVS-BC showed a higher selectivity toward MB compared to other organic contaminants. The MB-laden adsorbent was successfully used for the remediation of Cr (III), Ni (II), and Cd (II) with removal efficiencies hitting 100% following thermal activation.

Enhanced Escherichia coli removal from stormwater with bermudagrass-derived activated biochar filtration systems

Stormwater treatment and reuse can alleviate water pollution and scarcity while current sand filtration systems showed low treatment performance for stormwater. For enhancing E. coli removal in stormwater, this study applied the bermudagrass-derived activated biochars (BCs) in the BC-sand filtration systems for E. coli removal. Compared with the pristine BC (without activation), the FeCl3 and NaOH activations increased the BC carbon content from 68.02% to 71.60% and 81.22% while E. coli removal efficiency increased from 77.60% to 81.16% and 98.68%, respectively. In all BCs, the BC carbon content showed a highly positive correlation with E. coli removal efficiency. The FeCl3 and NaOH activations also led to the enhancement of roughness of BC surface for enhancing E. coli removal by straining (physical entrapment). The main mechanisms for E. coli removal by BC-amended sand column were found to be hydrophobic attraction and straining. Additionally, under 105-107 CFU/mL of E. coli, final E. coli concentration in NaOH activated BC (NaOH-BC) column was one order of magnitude lower than those in pristine BC and FeCl3 activated BC (Fe-BC) columns. The presence of humic acid remarkably lowered the E. coli removal efficiency from 77.60% to 45.38% in pristine BC-amended sand column while slightly lowering the E. coli removal efficiencies from 81.16% and 98.68% to 68.65% and 92.57% in Fe-BC and NaOH-BC-amended sand columns, respectively. Moreover, compared to pristine BC, the activated BCs (Fe-BC and NaOH-BC) also resulted in the lower antibiotics (tetracycline and sulfamethoxazole) concentrations in the effluents from the BC-amended sand columns. Therefore, for the first time, this study indicated NaOH-BC showed high potential for effective treatment of E. coli from stormwater by the BC-amended sand filtration system compared with pristine BC and Fe-BC.

Graphene as a rational interface for enhanced adsorption of microcystin-LR from water

Cyanotoxins such as microcystin-LR (MC-LR) represent a global environmental threat to ecosystems and drinking water supplies. The study investigated the direct use of graphene as a rational interface for removal of MC-LR via interactions with the aromatic ring of the ADDA1 chain of MC-LR and the sp2 hybridized carbon network of graphene. Intra-particle diffusion model fit indicated the high mesoporosity of graphene provided significant enhancements to both adsorption capacities and kinetics when benchmarked against microporous granular activated carbon (GAC). Graphene showed superior MC-LR adsorption capacity of 75.4 mg/g (Freundlich model) compared to 0.982 mg/g (Langmuir model) for GAC. Sorption kinetic studies showed graphene adsorbs 99% of MC-LR in 30 min, compared to zero removal for GAC after 24 hr using the same MC-LR concentration. Density functional theory (DFT), calculations showed that postulated π-based interactions align well with the NMR-based experimental work used to probe primary interactions between graphene and MC-LR adduct. This study proved that π-interactions between the aromatic ring on MC-LR and graphene sp2 orbitals are a dominant interaction. With rapid kinetics and adsorption capacities much higher than GAC, it is anticipated that graphene will offer a novel molecular approach for removal of toxins and emerging contaminants with aromatic systems.

Immobilization of Microcystin by the Hydrogel-Biochar Composite to Enhance Biodegradation during Drinking Water Treatment

Microcystin-LR (MC-LR), the most common algal toxin in freshwater, poses an escalating threat to safe drinking water. This study aims to develop an engineered biofiltration system for water treatment, employing a composite of poly(diallyldimethylammonium chloride)-biochar (PDDA-BC) as a filtration medium. The objective is to capture MC-LR selectively and quickly from water, enabling subsequent biodegradation of toxin by bacteria embedded on the composite. The results showed that PDDA-BC exhibited a high selectivity in adsorbing MC-LR, even in the presence of competing natural organic matter and anions. The adsorption kinetics of MC-LR was faster, and capacity was greater compared to traditional adsorbents, achieving a capture rate of 98% for MC-LR (200 μg/L) within minutes to tens of minutes. Notably, the efficient adsorption of MC-LR was also observed in natural lake waters, underscoring the substantial potential of PDDA-BC for immobilizing MC-LR during biofiltration. Density functional theory calculations revealed that the synergetic effects of electrostatic interaction and π-π stacking predominantly contribute to the adsorption selectivity of MC-LR. Furthermore, experimental results validated that the combination of PDDA-BC with MC-degrading bacteria offered a promising and effective approach to achieve a sustainable removal of MC-LR through an "adsorption-biodegradation" process.

Practical approach of As(V) adsorption by fabricating biochar with low basicity from FeCl3 and lignin

One of the main challenges of biochar application for environmental cleanup is rise of pH in water or soil due to high ash and alkali metal contents in the biochar. While this intrinsic property of biochar is advantageous in alleviating soil and water acidity, it severely impairs the affinity of biochar toward anionic contaminants such as arsenic. This study explored a technical approach that can reduce the basicity of lignin-based biochar by utilizing FeCl₃ during production of biochar. Three types of biochar were produced by co-pyrolyzing feedstock composed of different combinations of lignin, red mud (RM), and FeCl₃, and the produced biochar samples were applied to adsorption of As(V). The biochar samples commonly possessed porous carbon structure embedded with magnetite (Fe₃O₄) particles. The addition of FeCl₃ in the pyrolysis feedstock had a notable effect on reducing basicity of the biochar to yield significantly lower solution pH values than the biochar produced without FeCl₃ addition. The extent of As(V) removal was also closely related to the final solution pH and the greatest As(V) removal (>77.6%) was observed for the biochar produced from co-pyrolysis of lignin, RM, and FeCl₃. The results of adsorption kinetics and isotherm experiments, along with x-ray spectroscopy (XPS), strongly suggested adsorption of As(V) occurred via specific chemical reaction (chemisorption) between As(V) and Fe-O functional groups on magnetite. Thus, the overall results suggest the use of FeCl₃ is a feasible practical approach to control the intrinsic pH of biochar and impart additional functionality that enables effective treatment of As(V).

Advancement of biochar-aided with iron chloride for contaminants removal from wastewater and biogas production: A review

The use of fossil fuels, emission of greenhouse gases (GHG) into the atmosphere, and waste pose a problem to the environment and public health that urgently needs to be dealt with. Among numerous chemical activating agents that can be added to anaerobic digestion (AD) to enhance nutrient removal and increase the quality and quantity of biomethane, iron chloride (FeCl₃) is the one that has the lowest cost and is the most environmentally friendly. This state-of-the-art review aims to revise the influence of FeCl₃ on the Brunauer-Emmett-Teller (BET) surface area of biochar and its ability to increase methane (CH₄) yield and remove contaminants from biogas and wastewater. The novelty of the study is that FeCl₃, an activating agent, can increase the BET surface area of biochar, and its efficacy increases when combined with zinc chloride or phosphoric acid. Regarding the removal of contaminants from wastewater and biogas, FeCl₃ has proven to be an effective coagulant, reducing the chemical oxygen demand (COD) of wastewater and hydrogen sulfide in biogas. The performance of FeCl₃ depends on the dosage, pH, and feedstock used. Therefore, FeCl₃ can increase the BET surface area of biochar and CH₄ yield and remove contaminants from wastewater and biogas. More research is needed to investigate the ability of FeCl₃ to remove water vapor and carbon dioxide during biogas production while accounting for a set of other parameters, including FeCl₃ size.

Escherichia coli inactivation in water by sulfate radical-based oxidation process using FeCl3-activated biochar/persulfate system

Pathogenic microbes in water present great risks to environments, water resources, and human health. In the present study, for the first time, a FeCl₃-activated bermudagrass-derived biochar (FA-BC) was applied to activate persulfate (PS) for E. coli inactivation. The PS activation was ascribed to the presence of Fe⁰ and Fe₃O₄ on the surface of FA-BC, and SO₄^·- radicals were proved to be the main role for E. coli inactivation using FA-BC activated PS system (FA-BC/PS). Decreasing the pH (5-9) and increasing the PS concentration (50-300 mg/L), reaction temperature (20-50 °C), and FA-BC dosage (100-500 mg/L) resulted in the enhancement of disinfection efficiency of E. coli using FA-BC/PS. 6.21 log reductions of E. coli were achieved within 20 min under the optimal conditions (500 mg/L FA-BC, 200 mg/L PS, pH 7, and 20 °C with 10⁷ CFU/mL E. coli in DI water). The FA-BC/PS effectively eliminated various initial concentrations of E. coli (10⁵-10⁸ CFU/mL). The E. coli inactivation rate decreased from 0.1426 min^-1 to 0.0883, 0.1268 min^-1, and 0.1093 min^-1 with the presence of 10 mg/L humic acid, 100 mg/L Cl^-, and 100 mg/L HCO₃^-, respectively. In addition, after three cycles of disinfection tests using FA-BC/PS, the E. coli inactivation rate only slightly decreased from 0.1426 to 0.1288 min^-1. The FA-BC/PS also effectively removed the E. coli in real stormwater with a 99.2 % inactivation efficiency within 180 min. The FA-BC/PS in fixed-bed column tests revealed the continuous and high inactivation of E. coli in water. Increasing the FA-BC amount (1.5 %-5 %) and PS concentration (50-200 mg/L) and decreasing the flow rate (2-4 mL/min) caused the lower E. coli concentration in effluent. Therefore, the FA-BC/PS can be considered as a promising and efficient technique for water disinfection.

Adsorption of recalcitrant contaminants of emerging concern onto activated carbon: A laboratory and pilot-scale study

According to the World Health Organization (WHO), the definition of water quality indicators, including contaminants of emerging concern (CECs), associated with the development of multi-barrier approaches for wastewater treatment, are crucial steps towards direct potable reuse of water. The aims of this study were 1) quantifying twelve CECs (including pharmaceutical, stimulant, and artificial sweetener compounds) in both untreated and treated wastewater samples in a Brazilian wastewater treatment plant (WWTP) using bidimensional liquid chromatography coupled with tandem mass spectrometry, allowing the selection of five marker (i.e., priority) CECs; 2) evaluating the adsorption potential of such selected CECs [caffeine, hydrochlorothiazide, saccharin, sucralose (SUC), and sulfamethoxazole (SMX)] onto coconut-shell granular activated carbon (GAC); and 3) investigating the removal of the same CECs by a multi-barrier system (pilot-scale, 350 L h^-1) treating the effluent of the WWTP and composed of reverse osmosis (RO), photoperoxidation (UV/H₂O₂), and filtration with GAC. Such technologies were tested separately and in binary or ternary combinations. Eleven and eight CECs were detected and quantified on the untreated and treated wastewater samples of the Brazilian WWTP, respectively. For the treated wastewater, the concentrations ranged from 499 ng L^-1 (SMX) to 87,831 ng L^-1 (SUC). The adsorption onto AC data fitted the Sips isotherm model, indicating monolayer chemisorption, which was also suggested by the mean adsorption energy values (>16 kJ mol^-1). SMX and SUC were the most and the least adsorbed CECs (4.33 and 1.21 mg g^-1, respectively). Concerning the pilot-scale treatment plant, the ternary combination (RO + UV/H₂O₂+GAC) removed >99% of the five marker CECs and promoted reductions on water color, turbidity, as well as on nitrogen and phosphorus concentrations. Further studies on water reuse could prioritize the selected marker CECs as quality indicators. While the removal of marker CECs is one of the WHO performance requirements, the RO + UV/H₂O₂+GAC system showed promising results as a first approach to direct potable reuse of water.

Integrating adsorption and in situ advanced oxidation for the treatment of organic wastewater by 3D carbon aerogel embedded with Fe-doped carbonitrides

Wastewater containing organic pollutants with high toxicity and poor biodegradability poses a considerable threat to human health and the ecosystem. Although adsorption and advanced oxidation processes (AOPs) are currently the most widely used technologies for wastewater treatment, limitations of these two independent processes make the treatment effect unsatisfactory. Herein, a system of integrating adsorption and subsequent in situ AOPs is established by a 3D carbon aerogel embedded with Fe-doped carbonitrides (Fe-NC/CAG). The SEM and BET analysis demonstrate that Fe-NC/CAG possesses porous structures with a specific surface area of 518.7 m²/g. The XRD result indicates the formation of Fe⁰ and Fe₃O₄ in Fe-NC/CAG. The impacts of operational parameters such as Fe-NC/CAG dosage, pollutants concentration, temperature, initial pH, and inorganic ions on the adsorption efficiency are investigated. The adsorption kinetics is predominantly based on the pseudo-second-order model. After adsorbing organic pollutants, the Fe-NC/CAG is immersed in peroxymonosulfate (PMS) solution. The adsorbed pollutants are in situ degraded by PMS-based AOPs, leading to the regeneration of Fe-NC/CAG. At optimum conditions, the integrating process established by Fe-NC/CAG achieves over 90% removal of antibiotics, phenolics, and dyes as well as keeps stable performance even after 6 cycles. This integrating adsorption and AOPs system is expected to open up a rich field for wastewater treatment.

Synthesis, Adsorption Isotherm and Kinetic Study of Alkaline- Treated Zeolite/Chitosan/Fe3+ Composites for Nitrate Removal from Aqueous Solution-Anion and Dye Effects

In the present study, alkaline-treated zeolite/chitosan/Fe³⁺ (ZLCH-Fe) composites were prepared and analyzed using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and pH of zero point of charge (pH_zpc) to remove nitrates from water. The process was carried out using an adsorption method with a varied initial pH, adsorbent dosage, initial nitrate concentration and contact time. The pH_zpc demonstrated that the ZLCH-Fe surface had a positive charge between 2 and 10, making it easier to capture the negative charge of nitrate. However, the optimal pH value is 7. After 270 min, the maximum adsorption capacity and percent removal reached 498 mg/g and 99.64%, respectively. Freundlich and pseudo-second-order were fitted to the adsorption isotherm and kinetic models, respectively. An evaluation was conducted on the effects of anions-SO₄^2- and PO₄^3--and dyes-methylene blue (MB) and acid red 88 (AR88)-upon nitrate removal. The results indicated that the effect of the anion could be inhibited, in contrast to dye effects. However, the optimal pH values were changed to 10 for MB and 2 for AR88, resulting in a hydrogel formation. This might be indicated by the protonation of hydroxyl and amino groups resulting from a chitosan nitrate reaction in the AR88 solution.

FeCl3-activated biochar catalyst for heterogeneous Fenton oxidation of antibiotic sulfamethoxazole in water

One-step FeCl₃-mediated pyrolysis/activation was developed for preparation of bermudagrass (BG)-derived FeCl₃-activated biochars (FA-BCs) from bermudagrass (BG) as a heterogenous Fenton catalyst for heterogeneous Fenton oxidation of sulfamethoxazole (SMX) in water. The FA-BC prepared at the FeCl₃ to BG mass ratio of 2 (FA-BC) exhibited higher adsorption and Fenton oxidation of SMX than other mass ratios of the FeCl₃ to BG. FA-BC presented the great surface area (835 m²/g) and high SMX adsorption capacity (195 mg SMX/g BC), which was higher than various BCs in the previous studies. Additionally, the surface of FA-BC was attached with Fe₂O₃, Fe⁰, and Fe₃O₄ after the FeCl₃ activation. Under the optimal conditions for Fenton reaction (SMX concentration, 100 mg/L; loading of FA-BC, 0.1 g/L; dose of H₂O₂, 200 mg/L; temperature, 20 °C; pH 3; reaction time, 12 h), SMX and COD removal efficiencies reached 99.94% and 65.19%, respectively. Increasing reaction temperature from 20 to 50 °C significantly improved the SMX oxidation rate from 0.46 to 1.04 h^-1. The HO· radicals were proved to play a major role during the Fenton oxidation of SMX. In addition, the SMX solution treated by Fenton oxidation showed much less toxicity than the initial SMX solution. Additionally, the reusability tests of FA-BC indicated that 89.58% removal efficiency for SMX was still achieved after 3 cycles of Fenton oxidation under the optimal conditions. Furthermore, FA-BC can also efficiently remove SMX from the dairy wastewater. Therefore, FA-BC showed a high potential to eliminate aqueous SMX through adsorption and heterogeneous Fenton oxidation.

Sustainable use of Ca(OH)2 modified biochar for phosphorus recovery and tetracycline removal from water

To prevent possible secondary pollution from phosphorus-loaded biochar (BC) in agricultural systems, this study investigated the sustainable use of Ca(OH)₂ modified wood biochars (Ca-BCs) for P recovery while significantly lowering the tetracycline (TC) adsorption onto Ca-BCs. Ca-BCs were prepared via calcination of mixtures of Ca(OH)₂ and wood BC under 100-500 °C for removing P and TC from water. Compared to the pristine BC (without Ca(OH)₂ modification), Ca-BC100 (Ca-BC prepared at 100 °C) showed a significant increase of P adsorption capacity from 4.00 to 138.70 mg/g due to reactive interaction between P and Ca(OH)₂ on Ca-BC while decrease of TC adsorption capacity from 62.17 to 20.86 mg/g owing to decrease of surface area from 260.50 to 120.26 m²/g. Batch adsorption tests implied that the P adsorption on Ca-BC100 would occur mainly via electrostatic attraction (pH > 2.1) and formation of hydroxylapatite (Ca₅(PO₄)₃(OH)) between phosphate and Ca(OH)₂. In addition, Ca-BC100 reacted with TC via electrostatic attraction (pH > 7.6), complexation, hydrogen bond, and π-π interactions. P and TC adsorption onto Ca-BC100 was a chemical, endothermic, and spontaneous process. The dynamic adsorption experiments using a fixed bed column filled with Ca-BC100 indicated that Ca-BC100 could continuously and effectively remove P and TC from water. Ca-BC100 also effectively lowered P and COD in the dairy wastewater. Under the environmentally relevant conditions, continuous treatment of water containing P and TC using the pristine BC followed by Ca-BC100 showed the pristine BC removed 96% of TC and only 6% of P from water while Ca-BC100 made high recovery of P (94% of P) with negligible TC. Therefore, Ca-BC100 could be used for effective recovery of P with negligible TC from wastewater, and then applied to agricultural systems as a sustainable and safe P-rich biofertilizer.

Strain-boosted hyperoxic graphene oxide efficiently loading and improving performances of microcystinase

Harmful Microcystis blooms (HMBs) and microcystins (MCs) that are produced by Microcystis seriously threaten water ecosystems and human health. This study demonstrates an eco-friendly strategy for simultaneous removal of MCs and HMBs by adopting unique hyperoxic graphene oxides (HGOs) as carrier and pure microcystinase A (PMlrA) as connecting bridge to form stable HGOs@MlrA composite. After oxidation, HGOs yield inherent structural strain effects for boosting the immobilization of MlrA by material characterization and density functional theory calculations. HGO₅ exhibits higher loading capacities for crude MlrA (1,559 mg·g⁻¹) and pure MlrA (1,659 mg·g⁻¹). Moreover, the performances of HGO₅@MlrA composite, including the capability of removing MCs and HMBs, the ecological and human safety compared to MlrA or HGO₅ treatment alone, have been studied. These results indicate that HGO₅ can be used as a promising candidate material to effectively improve the application potential of MlrA in the simultaneous removal of MCs and HMBs.

•

Hyperoxic graphene oxide (HGO₅) provides inherent strain effects

•

HGO₅ exhibits an impressive loading capacity for MlrA

•

A new assembly mechanism for the HGO₅@MlrA composite is proposed

•

HGO₅@MlrA composite shows excellent capability and ecological safety

Adsorbents Used for Microcystin Removal from Water Sources: Current Knowledge and Future Prospects

The increasing occurrence of toxic cyanobacteria in water sources, driven by climate change and eutrophication, is of great concern worldwide today. Cyanobacterial blooms can negatively affect water bodies and generate harmful secondary metabolites, namely microcystins (MCs), which significantly impair water quality. Various adsorbents used for MC removal from water sources were assessed in this investigation. Activated carbon constitutes the most widely used adsorbent for treating contaminated waters due to its high affinity for adsorbing MCs. Alternative adsorbents have also been proposed and reported to provide higher efficiency, but the studies carried out so far in this regard are still insufficient. The mechanisms implicated in MC adsorption upon different adsorbents should be further detailed for a better optimization of the adsorption process. Certainly, adsorbent characteristics, water pH and temperature are the main factors influencing the adsorption of MCs. In this context, optimization studies must be performed considering the effectiveness, economic aspects associated with each adsorbent. This review provides guidelines for more practical field applications of the adsorption in the treatment of waters actually contaminated with MCs.

Okara and okara modified and functionalized with iron oxide nanoparticles for the removal of Microcystis aeruginosa and cyanotoxin

Eutrophicating compounds promote the growth of cyanobacteria, which has the potential of releasing toxic compounds. Alternative raw materials, such as residues, have been used in efficient adsorption systems in water treatment. The aim of the present study was to apply the residue Okara in its original form and modified by hydrolysis with immobilization of magnetic nanoparticles as an adsorbent. For the removal, the cyanobacteria Microcystis aeruginosa was chosen, as well as its secondary metabolites, L-amino acids leucine and arginine (MC-LR microcystin), from aqueous solutions. The adsorbents presented a negative surface charge, and the x-ray diffraction (DRX) outcomes successfully demonstrated the immobilization of iron oxide nanoparticles on the adsorbents. The adsorbent with the best result was the Okara hydrolyzed and functionalized with iron oxide, which showed a 47% (qe = 804.166 cel/g) and 85% (qe = 116.94 µg/L) removal for the cyanobacteria cells and chlorophyll-a, respectively. The kinetics study demonstrated a pseudo-first-order adsorption with maximal adsorption in 480 minutes, removing 761 µg/L of chlorophyll-a. In this trial, a low organic material removal has occurred, with a removal rate of 5% (qe = 0.024 mg/g) in the analysis of compounds in absorbance by ultraviolet light (UV) monitored by optical density determination in 254 nm (OD254). Nevertheless, the reaction system with the presence of organic material removed 53,28% of the MC-LR toxin, with adsorption capacities of 2.84 µg/L in a preliminary trial conducted for two hours, arising as a potential and alternative adsorbent with a capacity of removing cyanobacteria and cyanotoxin cells simultaneously.

Thermally enhanced adsorption and persulfate oxidation-driven regeneration on FeCl3-activated biochar for removal of microcystin-LR in water

In this study, a cyclic process of adsorption and persulfate (PS) oxidation-driven regeneration using FeCl₃-activated biochar (FA-BC) was suggested as a novel remediation process to remove microcystin-LR (MC-LR) from water. For enhancing overall treatment efficiency and cost effectiveness, the impacts of temperature on adsorption and PS oxidation-driven regeneration were investigated. The increase of temperature resulted in the increase of MC-LR adsorption rate on FA-BC due to the enhanced MC-LR diffusivity in water. Moreover, the MC-LR oxidation and PS reaction rates during the PS regeneration on FA-BC were remarkably improved by factors of 3.4 and 3.5 with increasing temperature from 20 °C to 50 °C. Both diffusion and desorption of MC-LR from FA-BC were thought to be the key factors for controlling the MC-LR oxidation rate during the PS regeneration of MC-LR. In addition, the decrease of pH (from 10 to 4) and increase of PS concentration (from 100 to 400 mg/L) enhanced the regeneration efficiency for MC-LR-spent FA-BC. The four cycles of adsorption-PS regeneration (200 mg/L PS, pH 6, and 50 °C) resulted in 92.81% regeneration efficiency in DI water and 82.89% in lake water. However, the four cycles of adsorption-PS regeneration led to the reduction of surface area (from 835 to 413 m²/g), oxidation of carbon surface and slight reduction of Fe⁰ on FA-BC. In overall, the cyclic adsorption-PS regeneration at higher temperature could provide practical reuse of FA-BC for cost-effective treatment of aqueous MC-LR.

Alleviation of microcystin-LR-induced hepatic lipidosis and apoptosis in zebrafish by use of rice straw-derived biochar

Microcystin-LR (MC-LR), mainly released by Microcystis aeruginosa, is posing a tremendous risk to aquatic animals and human health. Meanwhile, biochar (BC) is gradually be used as a sustainable adsorbent to immobilize and remove water pollutants. In our study, we for the first time conducted a full-scale investigation on lipid metabolism and its regulation mechanism of female zebrafish (Danio rerio) exposed to 0, 10 μg/L MC-LR, 100 μg/L BC, and 10 μg/L MC-LR+ 100 μg/L BC. The results indicated that sub-chronic MC-LR exposure induced hepatic lipidosis and apoptosis, including the formation of lipid droplets, significantly elevation of hepatic triglyceride (TG) level as well as significant upregulated expression of lipogenesis-related genes (foxo1a, elovl5, pparγ) and pro-apoptotic genes (bax, casp3). Nevertheless, no significant alteration was observed in the single BC group and the combined exposure group, which indicated that BC may solely functioned as an absorbent agent to lower MC-LR bioaccumulation in zebrafish liver and alleviate MC-LR-induced hepatotoxicity. Our findings revealed that the utilization of rice straw-derived BC can adsorb and immobile MC-LR in the water, subsequently alleviated the MC-LR-induced hepatic lipidosis and apoptosis in female zebrafish. On the basis of fish health, it is urgent to explore the feasibility of using environmentally friendly materials like BC to adsorb pollutants in water.