Photocatalytic properties of incorporated NiO onto clinoptilolite nano-particles in the photodegradation process of aqueous solution of cefixime pharmaceutical capsule

Photocatalytic degradation of Acid Red 18 by synthesized AgCoFe2O4@Ch/AC: Recyclable, environmentally friendly, chemically stable, and cost-effective magnetic nano hybrid catalyst

Chitosan (Ch) is a linear biodegradable natural carbohydrate polymer and the most appealing biopolymer, such as low-cost biodegradability, biocompatibility, hydrophilicity, and non-toxicity. In this case, Ch was utilized to synthesize AgCoFe2O4@Ch/Activated Carbon (AC) by the modified microwave-assisted co-precipitation method. The physical and chemical structure of magnetic nanocomposites was analyzed and characterized by Field Emission Scanning Electron Microscope (FESEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Energy Dispersive Spectroscopy (EDS), Diffuse Reflection Spectroscopy (DRS), Value stream mapping (VSM), Fourier transform spectroscopy (FTIR) and BET. The effects of various parameters on the removal of dye (Acid Red18), including catalyst dose, dye concentration, pH, and time were studied. Results showed that the highest removal efficiencies were 96.68 % and 84 % for the synthetic sample and actual wastewater, respectively, in optimal conditions (pH: 3, the initial dye concentration: 10 mgL-1, the catalyst dose: 0.14 gL-1, time: 50 min). Mineralization, according to the COD analysis, was 89.56 %. Photocatalytic degradation kinetics of Acid Red 18 followed pseudo-first order and Langmuir-Hinshelwood with constants of kc = 0.12 mg L-1 min-1 and KL-H = 0.115 Lmg-1. Synthesized photocatalytic AgCoFe2O4@Ch/AC showed high stability and after five recycling cycles was able to remove the pollutant with an efficiency of 85.6 %. So, the synthesized heterogenous magnetic nanocatalyst AgCoFe2O4@Ch/AC was easily recycled from aqueous solutions and it can be used in the removal of dyes from industries with high efficiency.

New breakthrough in rapid degradation of lignin derivative compounds · A novel high stable and reusable green organic photocatalyst

The pulp and paper sectors are thriving yet pose significant environmental threats to water bodies, mainly due to the substantial release of pollutants. Lignin-derived compounds are among the most problematic of these contaminants. To address this issue, we present our initial results on utilizing organic semiconductor photocatalysis under visible light for treating lignin-derived compounds. Our investigation has been centered around creating a green and cost-effective organic semiconductor photocatalyst. This catalyst is designed using a structure of bagasse cellulose spheres to support PM6 (poly[(2,6-(4,8-bis(5-(2-ethylhexyl)-4-fluorothiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene))-co-(1,3-di(5-thiophene-2-yl)-5,7-bis(2-ethylhexyl)-benzo[1,2-c:4,5-c']dithiophene-4,8-dione))]: MeIC (3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-cyclopentane-1,3-dione[c]-1-methyl-thiophe))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']-dithiophene)). This photocatalyst demonstrates remarkable efficiency, achieving over 91 % degradation of lignin-derived compounds. The superior photocatalytic performance is attributed to three main factors: (1) The ability of PM6 to broaden MeIC's absorption range from 300 to 800 nm, allowing for effective utilization of visible light; (2) the synergistic interaction between PM6 and MeIC, which ensures compatible energy levels and a vast, evenly spread surface area, promoting charge mobility and extensive donor/acceptor interfaces. This synergy significantly enhances the generation and transport of carriers, resulting in a high production of free radicals that accelerate the decomposition of organic materials; (3) The deployment of PM6:MeIC on biomass-based carriers increases the interaction surface with the organic substances. Notably, PM6: MeIC showcases outstanding durability, with its degradation efficiency remaining between 84 % and 91 % across 100 cycles. This study presents a promising approach for designing advanced photocatalysts aimed at degrading common pollutants in papermaking wastewater.

Constructing a Z-Scheme Co3O4/BiOBr Heterojunction to Enhance Photocatalytic Peroxydisulfate Oxidation of High-Concentration Rhodamine B: Mechanism, Degradation Pathways, and Toxicological Evaluations

Photocatalytic coupling technologies have emerged as popular strategies to increase the treatment efficiency of dye-containing wastewater. Herein, the Z-scheme Co3O4/BiOBr heterojunction (Z-CBH) was constructed and developed as a photocatalytic peroxydisulfate (PDS) activator for the degradation of high-concentration Rhodamine B (RhB). Multiple testing techniques were employed to confirm the formation of Z-CBHs. When 0.1 g·L-1 of Z-CBH20 and 1.0 mmol·L-1 of PDS were added simultaneously under simulated sunlight irradiation, the RhB degradation efficiency could approach 91.3%. Its reaction rate constant (0.01231 min-1) was much beyond the sum of those in the Z-CBH20/light system (0.00436 min-1) and the PDS/light system (0.0062 min-1). h+, •OH, •O2-, SO4•-, and 1O2 were detected as the dominant reactive species for RhB degradation. The potential mechanism of photocatalytic PDS oxidation was proposed. The possible intermediates were determined by high-performance liquid chromatography-quadrupole time-of-flight mass spectrometry assisted with density functional theory and Fukui theory. The possible degradation pathways of RhB degradation were put forward. The toxicological properties of RhB and its intermediates were evaluated by quantitative structure-activity relationship prediction. This work will not only provide a reference for developing photocatalytic persulfate activators but also gain an insight into the degradation pathways of RhB and the toxicity of its intermediates.

Congregating Ag into γ-Bi2O3 coupled with CoFe2O4 for enhanced visible light photocatalytic degradation of ciprofloxacin, Cr(VI) reduction and genotoxicity studies

The work attempts to construct a highly effective γ-Bi2O3/CoFe2O4/Ag visible active photocatalyst for the enhanced degradation of ciprofloxacin (CIP) and Cr(VI) reduction. γ-Bi2O3/CoFe2O4/Ag photocatalyst was prepared by simple solid phase and co-precipitation methods. The nanosphere shaped CoFe2O4 photocatalyst are embedded on top of γ-Bi2O3 nanotriangle. The addition of Ag into γ-Bi2O3/CoFe2O4 heterojunction primitively facilitates the photocatalytic activity in higher rate. The quantitative analysis of photocatalyst possesses to have lower e-/h+ recombination rate compared to its counterparts. The prepared γ-Bi2O3/CoFe2O4/Ag photocatalyst showed 96.6% degradation of CIP in 220 min and 99.2% reduction of Cr(VI) in 120 min. Additionally, γ-Bi2O3/CoFe2O4/Ag showed outstanding recyclability and long-term stability with a degradation efficiency of 96.5% even after six cycles. The intermediate products formed were identified and the degradation pathway was elucidated by gas chromatography-mass spectrometry analysis. Total organic carbon measurement was carried over to assess the efficiency of complete degradation and the removal percentage was found to be 98%. The end product toxicity study towards bacteria was proven to have less toxicity level when compared to parent compound. Lastly, the genotoxicity of γ-Bi2O3/CoFe2O4/Ag photocatalyst was tested in Allium cepa and the results confirmed to have no cause of toxicity impacts. Overall, the work not only tends to provide a highly visible active γ-Bi2O3/CoFe2O4/Ag photocatalyst, but also attributes to have no further negative imprints in the environment.

An experimental design study of photocatalytic activity of the Z-scheme silver iodide/tungstate binary nano photocatalyst

A binary AgI/ Ag2WO4 photocatalyst was fabricated and characterized by SEM, XRD, UV-Vis DRS, and FT-IR. It was then used to photodegrade sodium ceftriaxone (CTX) in an aqueous solution. The band gap energies of 2.95, 2.78, and 2.62 eV were obtained by the Kubelka-Munk model for Ag2WO4, AgI, and AgI/Ag2WO4 catalysts. The samples have pHPZC values of 6.9, 4.2, and 6.6, respectively. The synergistic photocatalytic activity of the coupled system depended on the AgI:Ag2WO4 mole ratio and grinding time (optimums:mole ratio of 4:1 and time 30 min). The experimental design was used for optimizing the conditions and a quadratic model well-processed the data based on the model F value of 131.87 > F0.05,14,13 = 2.55 and LOF F value of 0.78 < F0.05,10,3 = 8.78. The optimized RSM run included the irradiation time of 85 min, 3.5 mg/L of CTX sample at pH 9, and a catalyst dose of 1.0 g/L. Under the optimized conditions, about 63% of CTX molecules were photodegraded. In the study of the scavenging agents, the direct Z-scheme mechanism accumulated electrons in the CB-AgI and the holes in the VB-Ag2WO4 level, as stronger reducing and oxidizing centers than the accumulated electrons and holes of the type (II) heterojunction mechanism. Compared to a CTX oxidation potential of about 0.06 V, the direct Z-scheme mechanism is more favorable to reduce or oxidize it.

A facile two-step hydrothermal preparation of 2D/2D heterostructure of Bi2WO6/WS2 for the efficient photodegradation of methylene blue under sunlight

A facile two-step hydrothermal method was successfully used to prepare a photocatalyst Bi2WO6/WS2 heterojunction for methyl blue (MB) photodegradation. Fabricated photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray analysis (EDX), and X-ray photoelectron spectroscopy (XPS). Band gap measurements were carried out by diffuse reflectance spectroscopy (DRS). Results indicated that the prepared heterostructure photocatalyst has increased visible light absorption. Photocatalytic performance was evaluated under sunlight irradiation for methylene blue (MB) degradation as a model dye. Variations in pH (4-10), amount of catalyst (0.025-0.1 g/L), and initial MB concentrations (5-20 ppm) were carried out, whereas all prepared catalysts were used to conduct the tests with a visible spectrophotometer. Degradation activity improved with the pH increase; the optimum pH was approximately 8. Catalyst concentration is directly related to degradation efficiency and reached 93.56% with 0.075 g of the catalyst. Among tested catalysts, 0.01 Bi2WO6/WS2 has exhibited the highest activity and a degradation efficiency of 99.0% in 40 min (min) for MB. MB photodegradation follows pseudo-first-order kinetics, and obtained values of kapp were 0.0482 min-1, 0.0337 min-1, 0.0205 min-1, and 0.0087 min-1 for initial concentrations of 5 ppm, 10 ppm, 15 ppm, and 20 ppm, respectively. The catalyst was reused for six cycles with a negligible decrease in the degradation activity. Heterostructure 0.01 Bi2WO6/WS2 has exhibited a photocurrent density of 16 μA cm-2, significantly higher than 2.0 and 4.5 μA cm-2 for the pristine WS2 and Bi2WO6, respectively. The findings from these investigations may serve as a crucial stepping stone towards the remediation of polluted water facilitated by implementing such highly efficient photocatalysts.

Biosynthesis approach of copper nanoparticles, physicochemical characterization, cefixime wastewater treatment, and antibacterial activities

The aim of this paper is the green synthesis of copper nanoparticles (Cu NPs) via Quinoa seed extract. X-ray diffraction (XRD) results confirmed the production of the pure crystalline face center cubic system of the Cu NPs with an average crystallite size of 8.41 nm. Infrared spectroscopy (FT-IR) analysis confirmed the capping and stabilization of the Cu NPs bioreduction process. UV visible spectroscopy (UV-Vis). surface plasmon resonance revealed the absorption peak at 324 nm with an energy bandgap of 3.47 eV. Electrical conductivity was conducted assuring the semiconductor nature of the biosynthesized Cu NPs. Morphological analysis was investigated confirming the nano-characteristic properties of the Cu NPs as polycrystalline cubic agglomerated shapes in scanning electron microscopy (SEM) analysis. Transmission electron microscopy (TEM) analysis also was used to assess the cubic shapes at a particle size of 15.1 ± 8.3 nm and a crystallinity index about equal to 2.0. Energy dispersive spectroscopy (EDX) was conducted to investigate the elemental composition of the Cu NPs. As a potential utility of the biosynthesized Cu NPs as nano adsorbents to the removal of the Cefixime (Xim) from the pharmaceutical wastewater; adsorption studies and process parameters were being investigated. The following strategic methodology for maximum Xim removal was conducted to be solution pH 4, Cu NPs dosage 30 mg, Xim concentration 100 mg/L, and absolute temperature 313 K. The maximum monolayer adsorption capacity was 122.9 mg/g according to the Langmuir isothermal model, and the kinetic mechanism was pseudo-second-order. Thermodynamic parameters also were derived as spontaneous chemisorption endothermic processes. Antibacterial activity of the Xim and Xim@Cu NPs was investigated confirming they are highly potent against each Gram-negative and Gram-positive bacterium.

The enhance mechanism of DOM on tetracyclines degradation by electrochemical technology: A improvement of treatment processes

Tetracyclines (TC) is a typical broad-spectrum antimicrobial agent, and excessive use of TC can lead to a large accumulation of residual tetracycline in water. DOM is organic substances that can pass through the 0.45 μm filter. While dissolved organic matter (DOM) is one of the most significant substances in water, which has an important effect on water treatment. In this study, ultraviolet and visible spectrophotometry (UV-Vis) is applied to explore DOM to the effect of the electrochemical degradation. Three-dimension excitation emission matrix fluorescence spectroscopy (3D-EEM) is used to identify the component variation of DOM after the electrochemical oxidation (EO). Liquid chromatograph mass spectrometer (LC-MS) is used to confirm the degradation pathway of TC whether spontaneous or electrochemical oxidation. High performance liquid chromatography (HPLC) suggests the ROS production by DOM in the electrochemical oxidation under different conditions. Results show that DOM can promote the degradation of TC in the electrochemical oxidation. Tailwater DOM containssubstances can produce persistent free radicals, which can promote the degradation under light and dark conditions, natural source DOM can produce more free radicals under light. Therefore, TC wastewater should be added tailwater to promote the degradation of TC before the further water treatment. Otherwise, TC can be degraded to differentpathways (light, electricity, and degrade spontaneously). This study provides a significant idea for practical water treatment of tetracyclines, and promotes the practical application of electrochemical technology.

Improved catalytic performance of ZnO via coupling with CoFe2O4 and carbon nanotubes: A new, photocatalysis-mediated peroxymonosulfate activation system, applied towards Cefixime degradation

In this study, a ternary ZnO@spinel cobalt ferrite@carbon nanotube magnetic photocatalyst (ZSCF@CNT) was successfully synthesized and used to activate peroxymonosulfate (PMS) for Cefixime (CFX) antibiotic degradation under UVC irradiation. The morphology, optical, structural, and physicochemical properties of ZSCF@CNT were characterized and analyzed by XPS, XRD, FESEM-EDX, TEM, BET, VSM, UV-vis DRS and PL analysis. The results indicated that the ternary ZSCF@CNT photocatalyst exhibited superior catalytic activity on CFX elimination than that of individual components and binary composite catalysts, in which CFX with was rapidly removed under UVC irradiation and PMS. The effect of operational parameters including initial PMS, catalyst, and CFX concentrations and solution pH on the catalytic activity was investigated in detail; the optimal conditions were: pH: 7.0, catalyst: 0.3 g/L, PMS: 3.0 mM, leading to total CFX (10 mg/L) elimination in ∼20 min. Based on the radical scavenger tests, various radicals and non-radical species including sulfate, hydroxyl and superoxide radicals, singlet oxygen and electrons were involved in the ZSCF@CNT/PMS/UVC system. The high surface area, reduced agglomeration formation and excellent separation of photogenerated electron-hole pairs embodied in ZSCF@CNT photocatalyst conferred its superior catalytic activity and stability. The results from the tests in real water matrices revealed that ZSCF@CNT could be a promising photocatalyst to activate PMS for actual aqueous matrices' treatment.

Self-propelled nanojets an interfacial Schottky junctions modulated oxygen vacancies enriched for enhanced photo-Fenton degradation of organic contaminant: Improving H2O2 generation, Fe3+/Fe2+ cycle and enhancing plant metabolism

The study reports an innovative approach on sunlit driven heterostructure photocatalytic generation of H₂O₂ and removal of cefixime. In the present work, we have fabricated Mn/Mg doped CoFe₂O₄ modified CaCr₂O₄ decorated by Ag₃PO₄ quantum dots (Ag₃PO₄ QDs), a p-n-p nano heterojunction. The study promotes the photocatalytic production of H₂O₂ and self-Fenton photocatalytic degradation of cefixime. Egg white-assisted synthesis of Mn-doped CoFe₂O₄ causes the lattice oxygen defect, which enhances the photocatalytic activity. Lattice oxygen defect enable the adsorption of O₂, which enable the conversion of •O² in the valence band of CoFe₂O₄ for the endogenous production of H₂O₂. The higher in the surface area enhance the photocatalytic activity under visible light irradiation. Mn-CoFe₂O₄-CaCr₂O₄-Ag₃PO₄ QDs enables the complete photocatalytic degradation of cefixime (99.9%) and the complete removal was determined by total organic carbon (TOC) removal and it was around 99.4%. Meanwhile the photocatalytic degradation pathway of cefixime was determined by LC-MS/MS. Reusability of the nano heterojunction was determined by six cycle test, and the reusability of the nano heterojunction was 99.8%. Further, the toxicity of the nanomaterial was studied in maize plant and the results shows that the nanoheterojunction enhances the maize growth. The study systematically reveals the robust activity of nano heterojunction for sustainable water treatment.

A core/shell TiO2 magnetized molecularly imprinted photocatalyst (MMIP@TiO2): synthesis and its photodegradation activity towards sulfasalazine

Although the selectivity of TiO₂ for the degradation of target molecules is not enough, it is a broadly employed photocatalyst for the degradation of many pollutants. Molecularly imprinted compounds owing to their extreme recognition specificity have become increasingly popular for preparing selective photocatalysts. In this work, based on molecularly imprinted magnetized TiO₂ (MMIP@TiO₂), a selective photocatalyst was prepared. Via the co-precipitation method, Fe₃O₄ particles were prepared and coated respectively by SiO₂, vinyl end groups, and molecularly imprinted polymers (MIP). The synthesized photocatalyst was characterized by the X-ray diffraction method (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive x-ray spectrometry (EDX), vibrating sample magnetometry (VSM), high-performance liquid chromatography (HPLC), and photoluminescence analysis (PL). The photocatalyst was then used to degrade the sulfasalazine pharmaceutical pollutant under UV irradiation. An average crystallite size of 9 nm was obtained for the MMIP@TiO₂ sample from the Scherrer formula and 34.5 nm by the Williamson-Hall formula. The results revealed that compared to the non-imprinted counterpart, the molecularly imprinted photocatalyst had significantly higher efficiency and selectivity for the degradation of target molecules. The process was forwarded with 90% efficiency within 10 min. Optimal conditions were 10.0 min irradiation when 25 mL SSZ solution (50 mg/L), 0.07 g/L catalyst dose, and pH 6.0 were applied. The maximum removal efficiency was calculated to be 92%. The external magnetic field quickly removed the photocatalyst from the solution and regenerated it. It was revealed that after each regeneration cycle, the efficiency dropped. Nevertheless, 63% of the preliminary effectiveness remained after four regeneration steps.

MoS2/N-TiO2/Ti mesh plate for visible-light photocatalytic ozonation of naproxen and industrial wastewater: comparative studies and artificial neural network modeling

This paper presents the results of visible-light assisted photocatalytic ozonation for the degradation of naproxen as a model pharmaceutical pollutant from water using MoS₂/N-TiO₂ immobilized on a titanium mesh plate in addition to treatment of a real industrial wastewater. The batch studies were performed for naproxen degradation by varying the reaction variables such as ozone flow rate, initial pH and pollutant concertation. It was observed that almost 90% degradation was achieved at pH = 4, ozone flow rate = 3 L min^-1 and initial naproxen concentration = 5 mg L^-1. The catalyst exhibited constant activity even after seven successive cycles. Comparative studies among sorption, ozonation, photocatalysis, catalytic ozonation and photocatalytic ozonation revealed that the later process had the highest degradation of pollutant. Moreover, an artificial neural network (ANN) model was developed to simulate the performance of visible-light photocatalytic ozonation in naproxen degradation. The developed ANN model could estimate the visible-light photocatalytic ozonation process under the different experimental conditions. Finally, the applicability of the photocatalytic ozonation was successfully approved for industrial wastewater treatment. The results showed that the COD removal efficiency reached 65% within 150 min. HIGHLIGHTS: • MoS₂/N-TiO₂/Ti was synthesized by the quick electrophoretic deposition method. • The catalyst showed good ability in naproxen degradation via visible-light photocatalytic ozonation. • A three-layer artificial neural network model was developed to predict the naproxen degradation. • Naproxen degradation efficiency through the photocatalytic ozonation was higher than the individual methods. • COD of real wastewater was reduced significantly after the visible-light photocatalytic ozonation process.

Post-fabrication structural changes and enhanced photodegradation activity of semiconductors@zeolite composites towards noxious contaminants

This review article provides the recent progress in semiconductor-based zeolite photoactive materials for the application of noxious contaminants removal. The rapidly expanding industrialization and globalization cause serious threats to the environment or water bodies. The semiconductor@zeolite photocatalysts were implemented for water quality management/sustainment. The exclusive properties of zeolite material have been elaborated with their role in the photocatalysis process. The photoactive material's properties like single-atom catalysts (SACs), distribution of metal in the zeolite crystal were elaborated along with their role in catalytic reactions. Differently prepared semiconductor@zeolite composites such as TiO₂@zeolite, binary and ternary composites, Fe/Ag/bismuth-modified/ZnO/ZnS/NiO/g-C₃N₄/core-shell/quantum dots modified zeolite composites, were systematically summarized. The research progress in morphologies, structural effect, degradation mechanism were recapitulated and tabulated form of % degradation with their optimal parameters such as catalyst dose, pollutant concentrations, pH, light source intensities were also provided. The significance of zeolite frameworks, the structural properties of semiconductor@zeolite photoactive materials to enhance the degradation efficiencies was explored. Analysis of the intermediate products of Norfloxacin, TCDD (2,3,7,8-tetrachlorodibenzo-p-dioxin), TCDF (2,3,7,8-tetrachlorodibenzofuran), diclofenac contaminants were systematically represented and structurally identified by GC-MS/HPLC-MS techniques.

Photocatalytic Degradation of Cefixime Trihydrate by Bismuth Ferrite Nanoparticles

The present work was carried out to synthesize bismuth ferrite (BFO) nanoparticles by combustion synthesis, and to evaluate the photocatalytic activity of synthesized bismuth ferrite nanoparticles against cefixime trihydrate. BFO nanoparticles were successfully synthesized using bismuth (III) nitrate and iron (III) nitrate by a combustion synthesis method employing different types of fuels such as maltose, succinic acid, cinnamic acid, and lactose. The effects of the different types of fuels on the morphology and size of the bismuth ferrite nanoparticles were investigated. Characterization of the as-obtained bismuth ferrite nanoparticles was carried out by different techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), Energy-Dispersive Spectroscopy (EDS), N₂-sorption analysis, Fourier-transform infrared spectroscopy (FT-IR), and ultraviolet-visible (UV-vis) spectroscopy. Photoluminescence studies were also carried out for the various bismuth ferrite nanoparticles obtained. Degradation of cefixime trihydrate was investigated under sunlight to evaluate the photocatalytic properties of the bismuth ferrite nanoparticles, and it was found that the bismuth ferrite nanoparticles followed first-order degradation kinetics in solar irradiation in the degradation of antibiotic, cefixime trihydrate.

Photocatalytic kinetics of 2,4-dichloroaniline degradation by NiO-clinoptilolite nanoparticles

The ball-mill clinoptilolite nanoparticles (CNP) was ion-exchanged in Ni(II) solutions and calcined to obtain NiO-CNP catalysts with various NiO loadings. The resultant CNP was ion-exchanged in 0.1, 0.2, 0.3, and 0.4 M Ni(II) solutions and then calcined at 450 °C. The resultant NiO-CNPs contained 1.9, 2.3, 3.0, and 3.2% NiO, respectively. The XRD, FTIR, and DRS characterization techniques were applied. By applying the Scherrer equation on the XRD results, the average crystallite size for the NiO-CNP samples was estimated in the range of 42-65 nm. The pHpzc of the NiO-CNP species was slightly changed from 6.8 to 7.6 by an increase in the loaded NiO. The band gap energy of the samples was calculated by applying the Kubelka-Munk equation on the DRS results. The band gap energies of 3.81, 4.05, and 3.63 eV were estimated for the direct electronic transitions of the CN2, CN2.3, and CN3.2 samples, respectively. The boosted photoactivity was obtained in 2,4-dichloroanilyne (DCA) degradation when NiO supported onto both micronized clinoptilolite and its nanoparticles. The effects of the most important experimental variables on DCA photodegradation rate were kinetically studied by applying the Hinshelwood model on the results. The faster rate for the DCA photodegradation was achieved at the optimal conditions, including the catalyst dose: 0.5 g/L, C_DCA: 5 ppm, and the initial pH: 3. Some new peaks were observed in the HPLC chromatograms for the photodegraded DCA solutions after 180 min and 300 min, which showed 84% and 95% DCA photodegradation.

Bi/SnO2/TiO2-graphene nanocomposite photocatalyst for solar visible light-induced photodegradation of pentachlorophenol

In this study, for the first time, a TiO₂/graphene (G) heterostructure was synthesized and doped by Bi and SnO₂ nanoparticles through a hydrothermal treatment. The as-synthesized nanocomposite was employed for photocatalytic degradation of pentachlorophenol (PCP) under visible light irradiation. Structural characterizations such as X-ray photoelectron spectroscopy (XPS) and X-ray diffraction spectroscopy (XRD) proved the valence band alignment at Bi/SnO₂/TiO₂-G interfaces and crystallinity of the nanocomposite, respectively. The as-developed nanocomposite photocatalyst was able to decompose 84% PCP, thanks to the generation of a large number of active OH^•- and O₂^•- radicals. To achieve this optimum photodegradation efficiency, various parameters such as pH, catalyst dosage, and PCP concentration were optimized. The results showed that the PCP photodegradation process followed the first-order kinetic model and the reaction rate constant rose from 0.007 min^-1 (Bi) to 0.0149 min^-1 (Bi/SnO₂/TiO₂-G). The PCP photodegradation efficiency did not decrease significantly after 5 cycles, and the nanocomposite photocatalyst still showed a high efficiency of 68% in the last cycle. The excellent photocatalytic activity of Bi/SnO₂/TiO₂-G is ascribed as well as the heterostructure of the nanocomposite photocatalyst.

Green and efficient degradation of cefoperazone sodium by Bi4O5Br2 leading to the production of non-toxic products: Performance and degradation pathway

Photocatalytic process represents a promising approach to overcome the pollution challenge associated with the antibiotics-containing wastewater. This study provides a green, efficient and novel approach to remove cephalosporins, particularly cefoperazone sodium (CFP). Bi₄O₅Br₂ was chosen for the first time to systematically study its degradation for CFP, including the analysis of material structure, degradation performance, the structure and toxicity of the transformation products, etc. The degradation rate results indicated that Bi₄O₅Br₂ had an excellent catalytic activity leading to 78% CFP removal compared with the pure BiOBr (38%) within 120 min of visible light irradiation. In addition, the Bi₄O₅Br₂ presents high stability and good organic carbon removal efficiency. The effects of the solution pH (3.12 - 8.75) on catalytic activity revealed that CFP was mainly photocatalyzed under acidic conditions and hydrolyzed under alkaline conditions. Combined with active species and degradation product identification, the photocatalytic degradation pathways of CFP by Bi₄O₅Br₂ was proposed, including hydrolysis, oxidation, reduction and decarboxylation. Most importantly, the identified products were all hydrolysis rather than oxidation byproducts transformed from the intermediate of β-lactam bond cleavage in CFP molecule, quite different from the mostly previous studies. Furthermore, the final products were demonstrated to be less toxic through the toxicity analysis. Overall, this study illustrates the detailed mechanism of CFP degradation by Bi₄O₅Br₂ and confirms Bi₄O₅Br₂ to be a promising material for the photodegradation of CFP.

Visible Light Degradation of Naproxen by Enhanced Photocatalytic Activity of NiO and NiS, Scavenger Study and Focus on Catalyst Support and Magnetization

This research was aimed to prepare a magnetically photocatalyst enabling to degrade pharmaceutical wastewater and detoxification of pollutant such as naproxen, by visible light irradiation. The nano-sized NiS and NiO photocatalysts exhibit higher reactivity than their microsized counterparts, but separation of the used photocatalyst from the degradation solution is hard and imperfect. To remove this difficulty, magnetic polypyrrole core-shell (Fe₃ O₄ @PPY) was synthesized and employed as catalyst support. The magnetization property of the synthesized photocatalysts measured by VSM technique indicated that the photocatalysts were sufficiently magnetized to be readily separated from degradation solution by use of external magnetic field. The DRS study showed that the band gap of the photocatalysts shifted to lower energy after immobilization on the support materials leading to higher degradation efficiency. The optimal efficiency was obtained with the catalysts loaded with 50% of NiO and 50% of NiS. The augmenting effect of H₂ O₂ and the inhibition influence of some organic and inorganic compounds on the degradation process were studied. Regeneration of the used photocatalyst was performed by heat treatment, and the catalyst treated at 400°C retained most of its initial capacity. The degradation capacity was kinetically fast, and the equilibrium was attained within 30 min.

Solvothermal syntheses of Bi and Zn co-doped TiO2 with enhanced electron-hole separation and efficient photodegradation of gaseous toluene under visible-light

This study investigated the effects of Bi doped and Bi-Zn co-doped TiO₂ on photodegradation of gaseous toluene. The doped TiO₂ with various concentration of metal was prepared using the solvothermal route and characterized by SEM, XRD, Raman, BET, DRS, XPS, PL and EPR. Their photocatalytic activities under visible-light irradiation were drastically influenced by the dopant content. The results showed that moderate metal doping levels were obviously beneficial for the toluene degradation, while high doping levels suppressed the photocatalytic activity. The photocatalytic degradation of toluene over TiBi_1.9%O₂ and TiBi_1.9%Zn_1%O₂ can reach to 51% and 93%, respectively, which are much higher than 25% of TiO₂. Bi doping into TiO₂ lattice generates new intermediate energy level of Bi below the CB edge of TiO₂. The electron excitation from the VB to Bi orbitals results in the decreased band gap, extended absorption of visible-light and thus enhances its photocatalytic efficiency. Zn doping not only further enhances the absorption in this visible-light region, but also Zn dopant exists as the form of ZnO crystallites located on the interfaces of TiO₂ agglomerates and acts as a mediator of interfacial charge transfer to suppress the electron-hole recombination. These synergistic effects are responsible for the enhanced photocatalytic performance.