Simultaneous analysis of antioxidants and preservatives in cosmetics by supercritical fluid extraction combined with liquid chromatography-mass spectrometry

Human exposure characteristics of pharmaceutical and personal care product chemicals and associations with dietary habits

Considering the widespread presence of pharmaceutical and personal care products (PPCPs) in the environment and their adverse health effects, human exposure to PPCPs has caused worldwide concern. However, there remains insufficient information on the exposure assessment of the Chinese population. Based on this, the exposure levels of 13 PPCPs in the urine samples of 986 Chinese adults were measured, aiming to provide information on the prevalence of PPCP occurrence and investigate potential correlations between PPCP exposure and obesity. Results showed that the detection rates of these compounds in urine ranged from 28.12 % to 98.58 %, with median concentrations ranging below the limit of detection to 10.58 ng mL-1. Methyl-paraben (MeP) was the most dominant paraben and had the highest urinary concentration (median = 10.12 ng mL-1), while 4-hydroxy-benzophenone (4-OH-BP) was the dominant benzophenone derivative (median = 0.22 ng mL-1). In antibacterials, the urinary concentration of triclosan (mean = 42.00 ng mL-1) was much higher than that of triclocarban (mean = 0.63 ng mL-1). PPCP concentrations were significantly associated with sex, age, body mass index, education level, and annual household income (p < 0.050). Regression analysis of dietary habits showed that seafood and tea consumption may be significant exposure sources of PPCP exposure (p < 0.050). Furthermore, individual exposure to MeP (odds ratio (OR) < 1, p = 0.002) and 4-OH-BP (OR < 1, p = 0.009) exhibited a significantly negative association with obesity in females. Also, analysis results from quantile g-computation and Bayesian kernel machine regression models demonstrated that an inverse correlation between PPCP mixture exposure and obesity was significant in females. This study reports the extensive prevalence of PPCP exposure among adults from China, and may provide crucial insights into PPCP exposure dynamics. More epidemiological studies are need in the future, with a thorough knowledge of PPCP exposure.

Development of A Liquid-Phase Microextraction Method for Simultaneous Determination of Parabens in Lipstick Samples at Trace Levels by High-Performance Liquid Chromatography

The endocrine-disrupting potential of parabens, as well as their relation to cancer, has sparked significant discussions over their impact. Consequently, analyses of cosmetic products are an essential necessity, particularly in terms of human health and safety. In this study, a highly accurate and sensitive liquid-phase-based microextraction method was developed to determine the five parabens at trace levels by high-performance liquid chromatography. All prominent parameters of the method such as extraction solvent type and amount (1,2-dichloroethane/250 μL), and dispersive solvent type and amount (isopropyl alcohol/2.0 mL) were optimized to enhance the extraction efficiency of the analytes. The mobile phase consisting of 50 mM ammonium formate aqueous solution (pH 4.0) and acetonitrile (60:40, v/v) was used to elute the analytes at a flow rate of 1.2 mL min-1 in the isocratic mode. Analytical performance of the optimum method for methyl, ethyl, propyl, butyl and benzyl parabens were determined and the analytes recorded detection limit values of 0.78, 0.75, 0.34, 0.33 and 0.75 μg kg-1, respectively. Four different lipstick samples were analyzed under optimum conditions of the developed method, and the amount of parabens quantified in the samples using matrix matched calibration standards was in the range of 0.11-1.03%.

Impact of antioxidants on PM2.5 oxidative potential, radical level, and cytotoxicity

Antioxidants are typically seen as agents that mitigate environmental health risks due to their ability to scavenge free radicals. However, our research presents a paradox where these molecules, particularly those within lung fluid, act as prooxidants in the presence of airborne particulate matter (PM2.5), thus enhancing PM2.5 oxidative potential (OP). In our study, we examined a range of antioxidants found in the respiratory system (e.g., vitamin C, glutathione (GSH), and N-acetylcysteine (NAC)), in plasma (vitamin A, vitamin E, and β-carotene), and in food (tert-butylhydroquinone (TBHQ)). We aimed to explore antioxidants' prooxidant and antioxidant interactions with PM2.5 and the resulting OP and cytotoxicity. We employed OH generation assays and electron paramagnetic resonance assays to assess the pro-oxidative and anti-oxidative effects of antioxidants. Additionally, we assessed cytotoxicity interaction using a Chinese hamster ovary cell cytotoxicity assay. Our findings revealed that, in the presence of PM2.5, all antioxidants except vitamin E significantly increased the PM2.5 OP by generating more OH radicals (OH generation rate: 0.16-24.67 pmol·min-1·m-3). However, it's noteworthy that these generated OH radicals were at least partially neutralized by the antioxidants themselves. Among the pro-oxidative antioxidants, vitamin A, β-carotene, and TBHQ showed the least ability to quench these radicals, consistent with their observed impact in enhancing PM2.5 cytotoxicity (PM2.5 LC50 reduced to 91.2 %, 88.8 %, and 75.1 % of PM2.5's original level, respectively). Notably, vitamin A and TBHQ-enhanced PM2.5 OP were strongly associated with the presence of metals and organic compounds, particularly with copper (Cu) contributing significantly (35 %) to TBHQ's pro-oxidative effect. Our study underscores the potential health risks associated with the interaction between antioxidants and ambient pollutants.

Degradation of Butylated Hydroxyanisole by the Combined Use of Peroxymonosulfate and Ferrate(VI): Reaction Kinetics, Mechanism and Toxicity Evaluation

Butylated hydroxyanisole (BHA), a synthetic phenolic antioxidant (SPA), is now widely present in natural waters. To improve the degradation efficiency of BHA and reduce product toxicity, a combination of peroxymonosulfate (PMS) and Ferrate(VI) (Fe(VI)) was used in this study. We systematically investigated the reaction kinetics, mechanism and product toxicity in the degradation of BHA through the combined use of PMS and Fe(VI). The results showed that PMS and Fe(VI) have synergistic effects on the degradation of BHA. The effects of operational factors, including PMS dosage, pH and coexisting ions (Cl-, SO42-, HCO3-, K+, NH4+ and Mg2+), and different water matrices were investigated through a series of kinetic experiments. When T = 25 °C, the initial pH was 8.0, the initial BHA concentration was 100 μM, the initial concentration ratio of [PMS]0:[Fe(VI)]0:[BHA]0 was 100:1:1 and the degradation rate could reach 92.4% within 30 min. Through liquid chromatography time-of-flight mass spectrometry (LC-TOF-MS) identification, it was determined that the oxidation pathway of BHA caused by PMS/Fe(VI) mainly includes hydroxylation, ring-opening and coupling reactions. Density functional theory (DFT) calculations indicated that •OH was most likely to attack BHA and generate hydroxylated products. The comprehensive comparison of product toxicity results showed that the PMS/Fe(VI) system can effectively reduce the environmental risk of a reaction. This study contributes to the development of PMS/Fe(VI) for water treatment applications.

Development of Pegylated Nano-Phytosome Formulation with Oleuropein and Rutin to Compare Anti-Colonic Cancer Activity with Olea Europaea Leaves Extract

Olive leaf extract is a valuable source of phenolic compounds; primarily, oleuropein (major component) and rutin. This natural olive leaf extract has potential use as a therapeutic agent for cancer treatment. However, its clinical application is hindered by poor pharmacokinetics and low stability. To overcome these limitations, this study aimed to enhance the anticancer activity and stability of oleuropein and rutin by loading them into PEGylated Nano-phytosomes. The developed PEGylated Nano-phytosomes exhibited favorable characteristics in terms of size, charge, and stability. Notably, the anticolonic cancer activity of the Pegylated Nano-phytosomes loaded with oleuropein (IC50=0.14 μM) and rutin (IC50=0.44 μM) surpassed that of pure oleuropein and rutin alone. This outcome highlights the advantageous impact of Nano-phytosomes to augment the anticancer potential of oleuropein and rutin. These results present a promising pathway for the future development of oleuropein and rutin Nano-phytosomes as effective options for passive tumor-targeted therapy, given their improved stability and efficacy.

Ultrasound-assisted cloud point microextraction of certain preservatives in real samples and determination by HPLC

Ultrasound-assisted cloud point microextraction (UA-CPME) was performed for certain preservatives (p-hydroxy benzoic acid and its alkyl esters, methyl, ethyl, propyl and butyl parabens). Then, an HPLC method was developed for their simultaneous determination in pharmaceutical and cosmetic samples. The chromatograms of these substances were recorded on a C18 column using a gradient elution technique with various solvent systems at different flow rates and at 254 nm wavelength using a diode-array detector (DAD). The analysis conditions found by the classical method were optimized using the Box-Behnken design (BBD). In the design, the effect of each factor was examined with 3 and 4 factors for UA-CPME and HPLC analyses, respectively. The brij 58 concentration (BC), Na₂SO₄ amount (SA) and extraction time (ET) for UA-CPME, and the mobile phase 1 (MP1) ratio, mobile phase 2 (MP2) ratio, flow rate (FR) and column temperature parameters for HPLC analysis were obtained for the investigated levels. The factors affecting the resolution were determined by applying regression analysis to the experimental results. The analysis of variance (ANOVA) test was applied to ensure result reliability. The ANOVA test was used to determine the reliability of the results. A model was created with the obtained data. The developed method was validated by examining linearity, reproducibility, accuracy, limit of quantification and limit of the detection. Methyl paraben (with 0.148% RSD value and 0.060% relative error), and propyl paraben (with 0.149% RSD value and 0.120% relative error) were determined in the syrup sample by the developed method. Methyl paraben with recovery values of (98.32-99.42)% and ethyl paraben with recovery values of (99.17-99.41)%, were determined in a hand cream.

A MWCNTs-COOH/PSS nanocomposite-modified screen-printed electrode for the determination of synthetic phenolic antioxidants by HPLC with amperometric detection

New sensing platforms based on screen-printed carbon electrodes modified with composites based on polystyrene sulfonate and oxidized multi-walled carbon nanotubes (PSS/MWCNTs-COOH/SPCE) have been used to develop a novel HPLC method with electrochemical detection (ECD) for the determination of the most used synthetic phenolic antioxidants in cosmetics: butylhydroxytoluene (BHT), butylhydroxyanisole (BHA), tert-butylhydroquinone (TBHQ) and propyl gallate (PG). Optimal separation conditions were achieved using methanol: 0.10 mol L^-1 acetate solution at pH 6 as mobile phase with a gradient elution program from 60 to 90% of methanol percentage in 15 min. The electrochemical detection was carried out in amperometric mode using the PSS/MWCNTs-COOH/SPCE at + 0.80 V vs. Ag. Under these optimal separation and detection conditions, the limits of detection (LOD) were between 0.11 and 0.25 mg L^-1. These LOD values were better, especially for BHT, than those previously published in other HPLC methods. Linear ranges from 0.37 mg L^-1, 0.83 mg L^-1, 0.69 mg L^-1 and 0.56 mg L^-1 to 10 mg L^-1 were obtained for PG, TBHQ, BHA and BHT, respectively. RSD values equal or lower than 5% and 8% were achieved for repeatability and reproducibility, respectively. The HPLC-ECD method was successfully applied to analyze different cosmetic samples. Recovery values within 83-109% were obtained in the validation studies.

Recent Advances in Supercritical Fluid Extraction of Natural Bioactive Compounds from Natural Plant Materials

In this review, recent advances in greener technology for extracting natural bioactive components from plant origin sources are discussed. Bioactive compounds of plant origin have been defined as natural chemical compounds present in small amounts in plants. Researchers have shown interest in extracting bioactive compounds because of their human health benefits and characteristics of being eco-friendly and generally recognized as safe. Various new extraction methods and conventional extraction methods have been developed, however, until now, no unique approach has been presented as a benchmark for extracting natural bioactive compounds from plants. The selectivity and productivity of traditional and modern extraction techniques generally depend on selecting the critical input parameters, knowing the nature of plant-based samples, the structure of bioactive compounds, and good scientific skills. This work aims to discuss the recent advances in supercritical fluid extraction techniques, especially supercritical carbon dioxide, along with the fundamental principles for extracting bioactive compounds from natural plant materials such as herbs, spices, aromatic and medicinal plants.

A Novel HPLC Method for Simultaneous Determination of Methyl, Ethyl, n-propyl, Isopropyl, n-butyl, Isobutyl and Benzyl Paraben in Pharmaceuticals and Cosmetics

INTRODUCTION

The alkyl esters of p-hydroxybenzoic acid at the C-4 position, "the parabens," including methyl, ethyl, propyl, and butyl, are widely used as antimicrobial preservatives in foods, cosmetics, and pharmaceuticals. Official regulations on the use of these compounds make their analysis essential for the estimation of their exposure.

METHODS

On this basis, the presented study was realized to develop a simple, selective and cheap high-performance liquid chromatographic method for the quantitative determination of methylparaben, ethylparaben (EP), n-propyl paraben (NPP), isopropyl paraben (IPP), n-butyl paraben (NBP), isobutyl paraben (IBP) and benzyl paraben (BP) in pharmaceuticals and cosmetic products.

RESULTS

The chromatographic separation of the analytes was achieved under flow rate gradient elution conditions using a C18-bonded core-shell silica particle column (2.6 μm particle size, 150 × 3.0 mm from Phenomenex Co.). The samples were injected into the system as aliquots of 1.0 μL, and the compounds were detected by using a photodiode array detector set at 254 nm wavelength. With this technique, seven paraben derivatives can be determined in the concentration range of 250-2000 ng/mL. The recovery of the method is in the range of 99.95-13.84%, and the RSD is at a maximum value of 3.95%.

CONCLUSION

The proposed method was fully validated and successfully applied to different pharmaceutical and cosmetic samples (n=16), including syrups, suspensions, oral sprays, gels, etc. At least one paraben derivative was detected in six samples and was determined quantitatively. The maximum amount of a paraben derivative found in the analyzed samples was 321.7 ng/mL, which was MP. To the best of our knowledge, this is the first LC method, which is applicable both on pharmaceutical and cosmetic samples.

Development and validation of a headspace needle-trap method for rapid quantitative estimation of butylated hydroxytoluene from cosmetics by hand-portable GC-MS

Butylated hydroxytoluene (BHT) is widely used as a stable and inexpensive antioxidant in skin care products.

Easy-to-use and inexpensive sensors for assessing the quality and traceability of cosmetic antioxidants

We describe an easy-to-use sensor as a tool to quantify and authenticate antioxidant active ingredients in cosmetic products. The sensing platform comprises a responsive nanoengineered surface that reacts specifically and generates distinct optically detectable signals that are representative of the chemical composition and concentration of active ingredients. The platform can be inexpensively produced in large quantities and a procedure to manufacture the sensors by 3D printing is described. These sensors can be used as smart labels to check the quality of antioxidant constituents in a large variety of cosmetic products without involving any sample pretreatment. Possible applications include at home and on site testing by consumers or manufacturing companies to check the quality, shelf life and origin of raw materials and products during their manufacturing, storage and use.

A carbon paste electrode modified with a nickel titanate nanoceramic for simultaneous voltammetric determination of ortho- and para-hydroxybenzoic acids

An electrochemical sensor is described for the simultaneous determination of ortho-hydroxybenzoic acid (OHB) and para-hydroxybenzoic acid (PHB). The sensor consists of a carbon paste electrode modified with nickel titanate nanoceramics (NiTiO₃/CPE). The NiTiO₃ nanoceramics and the nanostructured modified CPE were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, electrochemical impedance spectroscopy and cyclic voltammetry. Differential pulse voltammetry indicates that the response to OHB (best measured at 0.90 V vs. Ag/AgCl) and PHB (measured at 0.80 V vs. Ag/AgCl) is significantly improved at the modified CPE compared to a bare CPE. The limits of detection (at S/N = 3) are 0.38 and 0.10 μM for OHB and PHB, respectively. The method was applied to the determination of the two isomers in peeling skin lotion and during the Kolbe-Schmitt reaction. Graphical abstract Nickel titanate nanoceramics (NiTiO₃) were synthesized by a sol-gel method. Then, a carbon paste electrode modified with NiTiO₃ (NiTiO₃/CPE) was constructed. The modified electrode was applied to the interference-free and simultaneous determination of ortho-hydroxybenzoic acid (OHB) and para-hydroxybenzoic acid (PHB).

In-Syringe Micro Solid-Phase Extraction Method for the Separation and Preconcentration of Parabens in Environmental Water Samples

In this study, a simple, rapid and effective in-syringe micro-solid phase extraction (MSPE) method was developed for the separation and preconcetration of parabens (methyl, ethyl, propyl and butyl paraben) in environmental water samples. The parabens were determined and quantified using high performance liquid chromatography and a photo diode array detector (HPLC-PDA). Chitosan-coated activated carbon (CAC) was used as the sorbent in the in-syringe MSPE device. A response surface methodology based on central composite design was used for the optimization of factors (eluent solvent type, eluent volume, number of elution cycles, sample volume, sample pH) affecting the extraction efficiency of the preconcentration procedure. The adsorbent used displayed excellent absorption performance and the adsorption capacity ranged from 227–256 mg g⁻¹. Under the optimal conditions the dynamic linear ranges for the parabens were between 0.04 and 380 µg L⁻¹. The limits of detection and quantification ranged from 6–15 ng L⁻¹ and 20–50 ng L⁻¹, respectively. The intraday (repeatability) and interday (reproducibility) precisions expressed as relative standard deviations (%RSD) were below 5%. Furthermore, the in-syringe MSPE/HPLC procedure was validated using spiked wastewater and tap water samples and the recoveries ranged between from 96.7 to 107%. In conclusion, CAC based in-syringe MSPE method demonstrated great potential for preconcentration of parabens in complex environmental water.

Crystal engineering of a zwitterionic drug to neutral cocrystals: a general solution for floxacins

The transformation of zwitterionic Sparfloxacin (SPX) to the neutral form is achieved by cocrystallization. Neutral forms of drugs are important for higher membrane permeability, while zwitterions are more soluble in water. The twin advantages of higher solubility/dissolution rate and good stability of neutral SPX are achieved in a molecular cocrystal compared to its zwitterionic SPX hydrate. The amine-phenol supramolecular synthon drives cocrystal formation, with the paraben ester acting as a "proton migrator" for the ionic to neutral transformation.

Simultaneous and rapid analysis of chemical preservatives in processed animal products by ultra-performance liquid chromatography

An ultra-performance liquid chromatography-tunable ultraviolet method was optimized and validated for the simultaneous analysis of nine chemical preservatives in processed animal products. The limits of detection and quantification for the preservatives were within the ranges of 0.02-0.23 and 0.07-0.76 μg/mL, respectively. The relative standard deviations for intraday analyses of retention time and peak area were 0.00-0.23 and 0.03-2.93%, respectively, whereas, those for interday analyses were 0.67-2.30 and 2.12-5.37%, respectively. Of the nine preservatives spiked into six different animal products, dehydroacetic acid spiked into soft cheese exhibited the lowest recovery rate of 72.1 ± 0.36% at the lowest concentration (0.25 g/kg). Comparing data between UPLC and high-performance liquid chromatography with a 5% significance level, the t-statistic was 1.42. Moreover, sorbic acid was detected in 16 animal products (0.11-2.49 g/kg) when 278 products were analyzed for preservatives.

Using thermal desorption electrospray ionization mass spectrometry to rapidly determine antimicrobial preservatives in cosmetics

RATIONALE

Characterization and quantification of permitted preservatives are important inspections to prevent the overuse of preservatives in authentic formulations. However, the complexity of sample matrices makes preservative determination in cosmetics a tedious process. A rapid analytical strategy to identify preservatives would insure large numbers of products are in compliance with government regulations.

METHODS

Thermal desorption electrospray ionization mass spectrometry (TD-ESI-MS) was used to directly detect preservative compounds in authentic formulations without sample pretreatment. The technique employs a metal probe, which was configured for sampling cosmetics in their original states and was inserted in a closed preheated oven to thermally desorb analytes. The desorbed analytes were then carried by a nitrogen gas stream into an ESI plume, where the formed ions were subsequently detected by the mass analyzer.

RESULTS

The TD-ESI mass and tandem mass spectra of different classes of preservative standards were rapidly obtained, and the limits of detection were far below the legal limit of their respective concentrations. The preservatives were also directly detected in different types of authentic formulations in the absence of sample preparation, and within a few seconds per sample. Calibration curves for preservatives in four common formulations yielded good linearity in the regulation-allowed range.

CONCLUSIONS

Due to its sensitivity, short analysis time, repeatability, and quantitative ability, TD-ESI-MS may serve as a suitable tool for large-scale screening of cosmetic preservatives to assure product safety. Copyright © 2016 John Wiley & Sons, Ltd.

Quantitative analysis of methyl and propyl parabens in neonatal DBS using LC–MS/MS

Aim: Excipients are used to overcome the chemical, physical and microbiological challenges posed by developing formulated medicines. Both methyl and propyl paraben are commonly used in pediatric liquid formulations. There is no data on systemic exposure to parabens in neonates. The European Study of Neonatal Exposure to Excipients project has investigated this. Results & methodology: DBS sampling was used to collect opportunistic blood samples. Parabens were extracted from the DBS and analyzed using a validated LC–MS/MS assay. Discussion & conclusion: The above assay was applied to analyze neonatal DBS samples. The blood concentrations of parabens in neonates confirm systemic exposure to parabens following administration of routine medicines.

Positive lists of cosmetic ingredients: Analytical methodology for regulatory and safety controls - A review

Cosmetic products placed on the market and their ingredients, must be safe under reasonable conditions of use, in accordance to the current legislation. Therefore, regulated and allowed chemical substances must meet the regulatory criteria to be used as ingredients in cosmetics and personal care products, and adequate analytical methodology is needed to evaluate the degree of compliance. This article reviews the most recent methods (2005-2015) used for the extraction and the analytical determination of the ingredients included in the positive lists of the European Regulation of Cosmetic Products (EC 1223/2009): comprising colorants, preservatives and UV filters. It summarizes the analytical properties of the most relevant analytical methods along with the possibilities of fulfilment of the current regulatory issues. The cosmetic legislation is frequently being updated; consequently, the analytical methodology must be constantly revised and improved to meet safety requirements. The article highlights the most important advances in analytical methodology for cosmetics control, both in relation to the sample pretreatment and extraction and the different instrumental approaches developed to solve this challenge. Cosmetics are complex samples, and most of them require a sample pretreatment before analysis. In the last times, the research conducted covering this aspect, tended to the use of green extraction and microextraction techniques. Analytical methods were generally based on liquid chromatography with UV detection, and gas and liquid chromatographic techniques hyphenated with single or tandem mass spectrometry; but some interesting proposals based on electrophoresis have also been reported, together with some electroanalytical approaches. Regarding the number of ingredients considered for analytical control, single analyte methods have been proposed, although the most useful ones in the real life cosmetic analysis are the multianalyte approaches.

Determination of synthetic phenolic antioxidants in soft drinks by stir-bar sorptive extraction coupled to gas chromatography-mass spectrometry

The synthetic phenolic antioxidants butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and tert-butyl hydroquinone (TBHQ) were pre-concentrated by stir-bar sorptive extraction and thermally desorbed (SBSE-TD) before analysis by GC-MS. Several parameters affecting the derivatisation step and both SBSE extraction and thermal desorption were carefully optimised. When the analyses of BHA and TBHQ in their acetylated, silylated and underivatised forms were compared, the best results were obtained when the in-situ derivatisation procedure with acetic anhydride was employed. Quantification was carried out using carvacrol as the internal standard, providing quantification limits of between 0.11 and 0.15 ng ml(-1), depending on the compound. Recovery assays for samples spiked at two concentration levels, 1 and 5 ng ml(-1), provided recoveries in the 81-117% range. The proposed method was applied in the analysis canned soft drinks and the analytes were found in five of the 10 samples analysed.

Simultaneous multicomponent spectrophotometric monitoring of methyl and propyl parabens using multivariate statistical methods after their preconcentration by robust ionic liquid-based dispersive liquid-liquid microextraction

A powerful and efficient signal-preprocessing technique that combines local and multiscale properties of the wavelet prism with the global filtering capability of orthogonal signal correction (OSC) is applied for pretreatment of spectroscopic data of parabens as model compounds after their preconcentration by robust ionic liquid-based dispersive liquid-liquid microextraction method (IL-DLLME). In the proposed technique, a mixture of a water-immiscible ionic liquid (as extraction solvent) [Hmim][PF6] and disperser solvent is injected into an aqueous sample solution containing one of the IL's ions, NaPF6, as extraction solvent and common ion source. After preconcentration, the absorbance of the extracted compounds was measured in the wavelength range of 200-700 nm. The wavelet orthogonal signal correction with partial least squares (WOSC-PLS) method was then applied for simultaneous determination of each individual compound. Effective parameters, such as amount of IL, volume of the disperser solvent and amount of NaPF6, were inspected by central composite design to identify the most important parameters and their interactions. The effect of pH on the sensitivity and selectivity was studied according to the net analyte signal (NAS) for each component. Under optimum conditions, enrichment factors of the studied compounds were 75 for methyl paraben (MP) and 71 for propyl paraben (PP). Limits of detection for MP and PP were 4.2 and 4.8 ng mL(-)(1), respectively. The root mean square errors of prediction for MP and PP were 0.1046 and 0.1275 μg mL(-)(1), respectively. The practical applicability of the developed method was examined using hygienic, cosmetic, pharmaceutical and natural water samples.