Surface characteristics of dental implants: A review

Immobilization of biofunctional molecule with potential osteoinductive efficacy on titanium implant for promoting early-stage osseointegration

In the present study, porcine-derived collagen type I was covalently immobilized on the surface of titanium (Ti) implants via carboxyl groups introduced by bonded p-vinylbenzoic acid to investigate its in vitro biocompatibility with gingival stem cells and in vivo bone regeneration behavior in the edentulous ridges of Lanyu small-ear pigs at weeks 2 and 6 (short-term effectiveness) through micro-computed tomography and histological analysis. Analytical results found that gingival stem cells showed effective adhesion and spreading on these collagen-immobilized implant surfaces. After 2 and 6 weeks of healing, significant differences in Hounsfield units were observed among the control (week 2 (674.2 ± 79.9) ∗∗p < 0.01 and week 6 (596.4 ± 49.6) ∗∗p < 0.01), buffer-coated implant (week 2 (768.1 ± 68.7) ∗p < 0.05 and week 6 (720.4 ± 62.6) ∗p < 0.05), and collagen-immobilized implant (week 2 (828.2 ± 69.4) and week 6 (907.4 ± 63.5)) groups. No significant differences in bone-to-implant contact ratios were discovered between the investigated groups. However, the bone surface area results demonstrated an enhanced bone apposition for the collagen-immobilized implants compared to the control and buffer-coated implants at weeks 2 and 6 post-implantation (∗p < 0.05). Therefore, this preclinical study underscores the advantageous impact of collagen immobilization on Ti implant surfaces for clinical application, substantiating its effectiveness through significant evidence of improved osseointegration at early-stages.

Anti-adherence capacity of phytosphingosine on titanium surfaces

Firm soft tissue attachment on oral implant components together with good bacterial control are important prerequisites for uneventful implant healing. TiO2 coatings have been shown to enhance human gingival fibroblast attachment, but the coating does not have antimicrobial properties. Phytosphingosine (PHS) is known to have antifouling properties against the cariogenic bacterium Streptococcus mutans (S. mutans) which is also among the first colonizers on implant surfaces. This makes PHS an interesting agent to prevent microbial adhesion on dental implant surfaces. The aim of this study was to examine the impact of PHS on S. mutans and human gingival fibroblast adhesion on titanium surfaces with or without TiO2 -coating. Titanium discs (n = 99, diameter 14 mm, thickness 1 mm) were fabricated for the study. The discs were divided into four groups: (1) non-coated discs (NC), (2) titanium discs with hydrothermally induced TiO2 coatings (HT), (3) NC discs treated with PHS solution and (4) HT discs treated with PHS solution. Hydrophilicity of the discs was evaluated by water contact angle measurement. S. mutans was added on HT and NC discs with or without PHS treatment for 30 minutes and the number of attached bacteria was estimated by plate counting method. For fibroblast experiment, the cells were plated on the discs and the number of adhered fibroblasts was determined at three time points (1, 3, 6 h). Additionally, confocal microscope images were obtained to examine fibroblast and S. mutans adhesion and to evaluate cell spreading. PHS treatment significantly decreased the hydrophilicity of HT and NC titanium surfaces (p < .001). S. mutans adhesion was significantly reduced after PHS treatment on both NC (p < .001) and HT surfaces (p < .001). Fibroblast adhesion was significantly reduced in HT group at 1 and 3h time points (p < .001), situation leveling out by the 6th hour. PHS reduced the number of adhered fibroblasts to the surface at incubation times of 1 hours (p = .0011) and 3 hours (p = .0194). At the 6 hour time point the number of adhered cells was no longer reduced, but still a reduction in cell spreading on the surface was observed (p < .05). The adhesion differences were present only in HT group. The PHS treatment reduced adherence of S. mutans and fibroblasts on TiO2 coated titanium, which may result from reduced hydrophilicity of the surfaces. The dual approach of PHS treatment and TiO2 coating could provide microbial antifouling properties of dental implants but may also affect fibroblast adhesion.

Electrolytic Cleaning of Dental Implants: A Scoping Review of Clinical Studies

Background/Objectives: This literature review aims to systematically analyze the efficacy of electrolytic cleaning for treating peri-implantitis, including its impact on disease resolution, re-osseointegration of treated implants, and peri-implantitis recurrence. It also compares various study and treatment protocols used in the selected papers. Methods: A comprehensive search was conducted in MEDLINE (via PubMed) and the Cochrane Central Register of Controlled Trials using the keywords "electrolytic cleaning implant" or "GalvoSurge". Studies published until 31 December 2024 were considered for inclusion. Results: Out of 141 articles retrieved, four publications were selected for the review. These studies were analyzed for implant type, number, evaluation methods, observation periods, surgical procedures, and additional treatments. Disease resolution was reported in one study, while peri-implantitis recurred in the remaining studies. However, re-osseointegration of treated implants was observed in all selected papers. Conclusions: Due to the limited and heterogeneous nature of the studies, it is difficult to draw definitive conclusions about the effectiveness of electrolytic cleaning as a treatment for peri-implantitis. To ensure consistent trial outcomes and improve predictability, clear clinical guidelines and surgical protocols for electrolytic decontamination are essential.

Comparative Study of Acid Etching and SLA Surface Modification for Titanium Implants

The dust generated during the sandblasting process of the sandblasted and acid-etched (SLA) method, commonly used to treat the surface of Ti dental implants, poses significant challenges in maintaining a clean manufacturing environment and ensuring safe working conditions. Nevertheless, surface modification remains crucial for improved performance of Ti dental implants. To address this problem and propose a clean and simple surface modification process to potentially replace SLA modification, this study aimed to characterize the surfaces of commercially pure Ti (cp-Ti) samples treated by acid etching and compare them with SLA-treated samples in terms of surface roughness (Rq), wettability (assessed through contact angle measurements), mineralized matrix deposition (evaluated through simulated body fluid [SBF] soaking), cell viability, cell differentiation (assessed based on alkaline phosphatase activity), and mineralization (assessed using MTT assay). Acid-etched surfaces exhibited nano- and micro-roughness and higher hydrophilicity than SLA surfaces, which is conducive to forming a highly bioactive TiO2 surface. Moreover, acid-etched samples exhibited earlier hydroxyapatite deposition after SBF soaking than SLA samples. Furthermore, the acid-etched surfaces were nontoxic and displayed significantly higher cell viability and differentiation after seven days than SLA surfaces. These findings suggest that acid etching is a viable alternative to the SLA method, likely offering superior surface bioactivity and biocompatibility.

Optimal submicron roughness for balancing degradation behavior, immune modulation, and microbial adhesion on zinc-based barrier membranes

Metallic zinc (Zn) has been demonstrated to be a promising alternative to barrier membrane materials for guided bone regeneration. Surface roughness significantly affects the properties of degradable Zn-based metals, especially within the Janus micro-environments of tissue regeneration. However, the effects of optimal surface roughness on Zn remain unknown. In this study, pure Zn surfaces were fabricated with three roughness scales: nano (Sa < 0.1 μm), submicron (Sa: 0.5-1.0 μm), and micron (Sa > 1.0 μm). Submicron-scale pure Zn exhibited a moderate degradation rate in simulated body fluids, and no deep corrosion pits appeared on the surface. By contrast, the degradation rate of nano-surface pure Zn decreased significantly, while localized corrosion tended to appear on micron surfaces. In addition, the degradation rate of Zn with different roughness was overall accelerated in artificial saliva, accompanied by varying degradation morphologies. Co-culturing with submicron samples inhibited macrophage polarization to the M1 phenotype. Nano-scale surfaces promoted macrophage polarization towards the M1 phenotype and exhibited significantly reduced antibacterial rates compared to rougher surfaces. These findings demonstrate that submicron-scale pure Zn could be an optimal choice for barrier membrane surfaces.

Finite element analysis of non-ultraviolet and ultraviolet-irradiated titanium implants

AIM

The purpose of this study is to calculate von Mises stresses, von Mises strains, deformation, principal stresses and principal elastic strains of non-UV and UV-irradiated hybrid SLA (sandblasted, large-grit, acid-etched)-coated titanium implants.

MATERIALS AND METHODS

A cross-sectional analytical study was conducted at the Institute of Dentistry, CMH Lahore Medical College. Cone beam computed tomography (CBCT) data of One Hundred and Thirty Eight Dio Hybrid sandblasted and acid-etched implants of identical dimensions (10 mm in length and 4.5 mm in diameter) were allocated in the three groups. Control group A samples were not given UV irradiation, while groups B and C were given UVA (382 nm, 25 mWcm-2) and UVC (260 nm, 15 mWcm-2) irradiation, respectively. The CBCT data were analyzed using FEA (ANSYS software). CBCT images were taken before functional loading (8th week) and after functional loading (26th week). A 3-way ANOVA test was employed to see the difference between the three groups. Tukey test was utilized for multiple comparisons. p ≤ 0.05 was considered significant.

RESULTS

The control group exhibited the highest average values for maximum von Mises stress, von Mises strain, deformation, principal stress, and principal elastic strain in both the maxilla and mandible compared to the UV-irradiated groups. Additionally, these measures consistently displayed higher averages in the maxilla across all groups compared to the mandible. Particularly, the UVC-irradiated group demonstrated the lowest von Mises stresses around the implants compared to the UVA group.

CONCLUSION

Insignificant differences were observed between UVA- and UVC-irradiated implants in terms of principal stress, deformation, von Mises strain, and principal elastic strain. The only notable distinction was in von Mises stress, where the UVC-irradiated group exhibited lower von Mises stress around SLA-coated titanium implants.

Microenvironment-responsive nanoparticles functionalized titanium implants mediate redox balance and immunomodulation for enhanced osseointegration

Various pathological conditions (e.g., diabetes, osteoporosis) are accompanied by persistent oxidative stress, which compromises the immune microenvironment and poses substantial challenges for osseointegration. Reactive oxygen species (ROS) play a "double-edged sword" role in bone tissue. Therefore, developing responsive biomaterials to maintain redox balance dynamically is crucial for enhanced osseointegration. Herein, the microenvironment-responsive coordination nanoparticles (C-Ca-SalB NPs) composed of salvianolic acid B (SalB), catechol-conjugated chitosan (CS-C), and Ca2+ are constructed and further covalently immobilized onto titanium implant surfaces. The resulting implants achieve on-demand antioxidant and immunomodulatory effects in a microenvironment-responsive manner, thus facilitating bone regeneration under both normal and oxidative conditions. Under physiological conditions, the functionalized implants display modest immunomodulatory properties without affecting oxidative balance, while C-Ca-SalB NPs remain relatively stable. However, the modified implants enable rapid decomposition of C-Ca-SalB NPs under acidic oxidative conditions, displaying robust ROS-scavenging, anti-inflammatory, and osteoinductive capacities, ultimately remodeling the pathological microenvironment into a regenerative one. Overall, smart implants with controlled bioactive agent release in this study present a comprehensive solution for enhancing bone-implant integration, particularly in the challenging context of oxidative stress.

Gingival keratinocyte adhesion on atomic layer-deposited hydroxyapatite coated titanium

This study aimed to evaluate the effects of the atomic layer deposited hydroxyapatite (ALD-HA) coating of the titanium (Ti) surface on human gingival keratinocyte (HGK) cell adhesion, spreading, viability, and hemidesmosome (HD) formation. Grade 2 square-shaped Ti substrates were used (n = 62). Half of the substrates were ALD-HA coated, while the other half were used as non-coated controls (NC). The ALD-HA surface was characterized with scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) analysis. The initial cell adhesion and HD formation of HGKs were evaluated after a 24-h cultivation period. The cell proliferation was assessed by cultivating cells for 1, 3, and 7 d. The expression levels of the integrin mediating cell adhesion were detected with the Western Blot method. In addition, cell spreading and expression of the proteins mediating cell adhesion were imaged using a confocal microscope. SEM-EDS analysis demonstrated the formation of HA on the ALD-HA surfaces. The relative cell attachment was significantly higher (p < .05) on the ALD-HA compared to the NC surface after 1 and 3 d of cell culture. No significant difference was found in integrin α6 or β4 expression. The microscope evaluation showed significantly increased cell spreading with peripheral HD expression on ALD-HA compared to the NC surfaces (p = .0001). Moreover, laminin γ2 expression was significantly higher on the ALD-HA than on the NC surfaces (p < .001). Compared to the NC Ti surface, the ALD-HA coating has favorable effects on HGK proliferation, growth, and cell spreading. This indicates that the ALD-HA coating has good potential for improving mucosal attachment on implant surfaces.

Tailoring magnesium-doped coatings for improving surface and biological properties of titanium-based dental implants

Physicochemical modifications of biomaterials have been proposed to overcome bone integration impairment and microbial infections. The magnesium (Mg) incorporation on dental implant surfaces has shown positive results in bone-to-implant contact and in the reduction of microbial colonization. Here, we explored the potential of using different Mg precursors to synthesize coatings via plasma electrolytic oxidation (PEO) on commercially pure titanium (cpTi), aiming to optimize the surface and biological properties. For this, we investigated Mg acetate and Mg nitrate precursors in different concentrations (0.04 M and 0.12 M), using calcium (Ca) and phosphorus (P) as the base electrolyte for all groups. Coatings with only the CaP base electrolyte were used as the control group. The surfaces were characterized by confocal laser scanning microscopy, scanning electron microscopy, film thickness measurement, profilometry, wettability, X-ray diffraction, energy dispersive spectroscopy, X-ray photoelectron spectroscopy, electrochemical behavior, and ion release. For biological analyses, the adhesion (2 h) of Streptococcus sanguinis was evaluated, as well as MC3T3-E1 osteoblastic cells proliferation at 1 and 3 days, and mineralization of calcium phosphates after 28 days. PEO treatment using different Mg precursors promoted physicochemical modifications of cpTi. The experimental groups MgN 0.04 and MgN 0.12 exhibited higher surface roughness and wettability compared to the other surfaces. Regardless of the Mg precursor, the higher the ion concentration in the electrolyte solution, the higher the Mg atomic concentration on the surfaces. Concerning the electrochemical behavior, the results indicated that the incorporation of Mg in the coatings may enhance the electrochemical performance. Mg treated surfaces did not promote greater bacterial adherence when compared to the control. MgAc 0.04 and MgAc 0.12 coatings displayed improved MC3T3-E1 pre-osteoblastic cells proliferation at day 3 compared to other groups. The hydroxyapatite formation on MgAc 0.12 surfaces was higher than in the other groups. Our data indicate that Mg precursor selection positively influences physicochemical and biological properties of coatings. Specifically, MgAc 0.12 surfaces showed the most promising surface features with greater cell proliferation, without affecting microbial colonization, being an excellent candidate for surface treatment of titanium-based dental implants.

Antibacterial Properties of PMMA/ZnO(NanoAg) Coatings for Dental Implant Abutments

Infections continue to pose significant challenges in dentistry, necessitating the development of innovative solutions that can effectively address these issues. This study focuses on creating coatings made from polymethyl methacrylate (PMMA) enriched with zinc oxide-silver composite nanoparticles, layered to Ti6Al4V-titanium alloy substrates. The application of these materials aims to create a solution for the abutments utilized in complete dental implant systems, representing the area most susceptible to bacterial infections. The nanoparticles were synthesized using a hydrothermal method, optimized through specific temperature and pressure parameters to achieve effective morphologies and sizes that enhance antibacterial efficacy. The layers were applied to the titanium substrate using the spin coating technique, chosen for its advantages and compatibility with the materials involved. Comprehensive analyses were conducted on the antimicrobial powders, including X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. Furthermore, the PMMA-based coatings incorporating antimicrobial nanoparticles were evaluated to ensure uniformity and homogeneity across the titanium alloy surface by IR mapping and SBF immersion-SEM analysis. The antimicrobial activity of the samples was demonstrated with impressive results against Staphylococcus aureus, Pseudomonas aeruginosa, and Candida albicans, as assessed through biofilm modulation studies. The biocompatibility of the samples was validated through in vitro cell-based assays, which demonstrated excellent compatibility between PMMA-based coatings and human preosteoblasts, confirming their potential suitability for future use in dental implants.

The Role of Nanomaterials in Diagnosis and Targeted Drug Delivery

Nanomaterials have evolved into the most useful resources in all spheres of life. Their small size imparts them with unique properties and they can also be designed and engineered according to the specific need. The use of nanoparticles (NPs) in medicine is particularly quite revolutionary as it has opened new therapeutic avenues to diagnose, treat and manage diseases in an efficient and timely manner. The review article presents the biomedical applications of nanomaterials including bioimaging, magnetic hypothermia and photoablation therapy, with a particular focus on disease diagnosis and targeted drug delivery. Nanobiosensors are highly specific and can be delivered into cells to investigate important biomarkers. They are also used for targeted drug delivery and deliver theranostic agents to specific sites of interest. Other than these factors, the review also explores the role of nano-based drug delivery systems for the management and treatment of nervous system disorders, tuberculosis and orthopaedics. The nano-capsulated drugs can be transported by blood to the targeted site for a sustained release over a prolonged period. Some other applications like their role in invasive surgery, photodynamic therapy and quantum dot imaging have also been explored. Despite that, the safety concerns related to nanomedicine are also pertinent to comprehend as well as the biodistribution of NPs in the body and the mechanistic insight.

Enhanced bacteriostasis and osseointegrative properties of SiRNA-modified polyetheretherketone surface for implant applications

Polyetheretherketone (PEEK), bearing an elastic modulus that effectively simulates the innate properties of natural bone, has come into the spotlight as a promising bone substitute material. Nonetheless, the biologically inert nature of PEEK, combined with its insubstantial osseointegration and sterilization capabilities, pose constraints on its clinical application in the realm of implants. RNA interference (RNAi), an effective technique used for gene expression regulation, has begun to be applied in implant surface modification. Herein, siCKIP-1 is securely affixed to the surface of PEEK implants, aided by an antibacterial polyphenol tannic acid (pTAN) coatings, enhancing physiologic osseointegration and inhibiting bacterial infection. This method breakthrough not merely facilitates the convenience, but also multifaceted PEEK implants' refinements. The modified PEEK implants have impressive biocompatibility coupled with a noteworthy degree of antibacterial properties. Meanwhile, modified PEEK implants improved osteogenic differentiation of rat bone mesenchymal stem cells (rBMSCs) and demonstrated excellent osteointegrative properties in rat femur implantation models. Therefore, identifying a new implant material with excellent biocompatibility and biomechanical properties is essential.

Comparison of osseointegration in commercial SLA-treated dental implants with different surface roughness: a pilot study in beagle dogs

PURPOSE

This pilot study investigated the effect of surface roughness on osseointegration by comparing two types of commercial SLA-treated dental implants with different surface roughness levels: moderately rough (Sa = 1 - 2 µm) and rough surfaces (Sa > 2 µm).

MATERIALS AND METHODS

Two implant groups were studied: TS (rough surface) and ADD (moderately rough surface) groups. Surface characteristics were analyzed using optical profilometry and SEM. In vitro studies using BRITER cells assessed cell adhesion, proliferation, and osteogenic differentiation through CCK-8 assay and qRT-PCR for osteopontin (OPN), osteocalcin (OCN), and alkaline phosphatase (ALP) expression. The in vivo study involved 12 implants (six per group) placed in mandibular defects of two beagle dogs. After 8 weeks, histomorphometric analysis evaluated bone to implant contact (BIC) and inter-thread bone density (ITBD). Statistical analysis used Student's t-test and two-way ANOVA for in vitro data, and Mann-Whitney U test for in vivo data.

RESULTS

Surface analysis revealed Sa values of 2.50 ± 0.27 µm for the TS group and 1.80 ± 0.06 µm for the ADD group. In vitro studies showed no significant differences in cell adhesion and proliferation between the groups (P > .05). However, gene expression patterns differed, with ADD group showing higher OPN expression (P < .001) and TS group showing higher ALP expression (P < .01). The in vivo study revealed no statistically significant differences in BIC and ITBD between the two groups (P > .05).

CONCLUSION

Surface roughness influenced osteoblast differentiation in vitro, but did not significantly affect osseointegration outcomes in vivo. Both moderately rough and rough surfaces appeared to support comparable levels of osseointegration. Larger studies are needed to confirm these findings and determine optimal implant surface characteristics.

Advances in osteoimmunomodulation of biomaterials after intrabone implantation: focus on surface hydrophilicity

Biomaterials intended for intrabone implantation are extensively utilized in orthopedic and dental applications. Their surface properties, particularly hydrophilicity, significantly influence the biological interactions surrounding the implant, ultimately determining the implant's in vivo fate. Recently, the role of osteoimmunomodulation in these implantable biomaterials has been recognized for its importance in regulating biomaterial-mediated osteogenesis. Consequently, it is imperative to elucidate the correlation between hydrophilicity and the immune response for the development of osteoimmunomodulatory implants. Herein, this review highlights recent advances in osteoimmunomodulation of biomaterials after intrabone implantation from a novel perspective-surface hydrophilicity, and summarizes the series of immune reactions and subsequent bone remodeling that occur in response to hydrophilic implants, focusing on protein adsorption, the behaviors of major immune cells, and osteoimmunomodulation-enhanced angiogenesis and osteogenesis. Hydrophilic biomaterials have the capacity to alter the surrounding immune microenvironment and accelerate the process of material-tissue bonding, thereby facilitating the successful integration of biomaterials with tissue. Collectively, the authors hope that this article provides strategies for modulating hydrophilicity to achieve osteoimmunomodulatory performance and further promotes the development of novel implantable biomaterials for orthopedic and dental applications.

Preparation of an anticoagulant polyethersulfone membrane by immobilizing FXa inhibitors with a polydopamine coating

Anticoagulation treatment for patients with high bleeding risk during hemodialysis is challenging. Contact between the dialysis membrane and the blood leads to protein adsorption and activation of the coagulation cascade reaction. Activated coagulation Factor X (FXa) plays a central role in thrombogenesis, but anticoagulant modification of the dialysis membrane is rarely targeted at FXa. In this study, we constructed an anticoagulant membrane using the polydopamine coating method to graft FXa inhibitors (apixaban and rivaroxaban) on the membrane surface. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and atomic force microscopy (AFM) were used to characterize the membranes. The apixaban- and rivaroxaban-modified membranes showed lower water contact angles, decreased albumin protein adsorption, and suppressed platelet adhesion and activation compared to the unmodified PES membranes. Moreover, the modified membranes prolonged the blood clotting times in both the intrinsic and extrinsic coagulation pathways and inhibited FXa generation and complement activation, which suggested that the modified membrane enhanced biocompatibility and antithrombotic properties through the inhibition of FXa. Targeting FXa to design antithrombotic HD membranes or other blood contact materials might have great application potential.

Innate immune regulation in dental implant osseointegration

PURPOSE

Dental implant osseointegration comprises two types of bone formation-contact and distance osteogenesis-which result in bone formation originating from the implant surface or bone edges, respectively. The physicochemical properties of the implant surface regulate initial contact osteogenesis by directly tuning the osteoprogenitor cells in the peri-implant environment. However, whether these implant surface properties can regulate osteoprogenitor cells distant from the implant remains unclear. Innate immune cells, including neutrophils and macrophages, govern bone metabolism, suggesting their involvement in osseointegration and distance osteogenesis. This narrative review discusses the role of innate immunity in osseointegration and the effects of implant surface properties on distant osteogenesis, focusing on innate immune regulation.

STUDY SELECTION

The role of innate immunity in bone formation and the effects of implant surface properties on innate immune function were reviewed based on clinical, animal, and in vitro studies.

RESULTS

Neutrophils and macrophages are responsible for bone formation during osseointegration, via inflammatory mediators. The microroughness and hydrophilic status of titanium implants have the potential to alleviate this inflammatory response of neutrophils, and induce an anti-inflammatory response in macrophages, to tune both contact and distance osteogenesis through the activation of osteoblasts. Thus, the surface micro-roughness and hydrophilicity of implants can regulate the function of distant osteoprogenitor cells through innate immune cells.

CONCLUSIONS

Surface modification of implants aimed at regulating innate immunity may be useful in promoting further osteogenesis and overcoming the limitations encountered in severe situations, such as early loading protocol application.

The Application Progress of Nonthermal Plasma Technology in the Modification of Bone Implant Materials

With the accelerating trend of global aging, bone damage caused by orthopedic diseases, such as osteoporosis and fractures, has become a shared international event. Traffic accidents, high-altitude falls, and other incidents are increasing daily, and the demand for bone implant treatment is also growing. Although extensive research has been conducted in the past decade to develop medical implants for bone regeneration and healing of body tissues, due to their low biocompatibility, weak bone integration ability, and high postoperative infection rates, pure titanium alloys, such as Ti-6A1-4V and Ti-6A1-7Nb, although widely used in clinical practice, have poor induction of phosphate deposition and wear resistance, and Ti-Zr alloy exhibits a lack of mechanical stability and processing complexity. In contrast, the Ti-Ni alloy exhibits toxicity and low thermal conductivity. Nonthermal plasma (NTP) has aroused widespread interest in synthesizing and modifying implanted materials. More and more researchers are using plasma to modify target catalysts such as changing the dispersion of active sites, adjusting electronic properties, enhancing metal carrier interactions, and changing their morphology. NTP provides an alternative option for catalysts in the modification processes of oxidation, reduction, etching, coating, and doping, especially for materials that cannot tolerate thermodynamic or thermosensitive reactions. This review will focus on applying NTP technology in bone implant material modification and analyze the overall performance of three common types of bone implant materials, including metals, ceramics, and polymers. The challenges faced by NTP material modification are also discussed.

The impact of hyaluronic acid coating on polyether ether ketone dental implant surface: An in vitro analysis

Objective

Polyether ether ketone (PEEK), a biocompatible polymer, is being explored as an alternative to metallic alloys for dental implants due to its aesthetic and mechanical properties. This study aimed to enhance the surface biofunctionality through evaluating human MG-63 osteoblastic cell survival, proliferation, differentiation, and mineralization.

Method

Following the sandblasting and plasma treatment of the 3D-printed PEEK discs, a layer of hyaluronic acid (Hya) was coated onto the PEEK surface. Osteoblast cells were seeded onto the discs. The groups consisted of Hya-coated PEEK, uncoated PEEK, and a control group. Cell viability, proliferation, differentiation, and mineralization potential were examined after seven and twenty-one days of cell seeding using the MTT test, DAPI staining technique, alkaline phosphatase activity (ALP), and alizarin red staining.

Results

Hya-coated PEEK increased cell viability (1.48 ± 0.13, 1.49 ± 0.09) compared to the uncoated group (1.19 ± 0.06, 1.26 ± 0.07) and control group (0.98 ± 0.04, 1.00 ± 0.07) after 7 and 21 days. Proliferation rates of coated group (60.50 ± 3.08) were greater than the uncoated (50.33 ± 2.58) and control group (38.33 ± 4.88) at 21 days, respectively. Additionally, the ALP activity on Hya-coated PEEK disks (5.55 ± 0.65, 7.54 ± 0.64) was notably higher than that of the uncoated group (1.08 ± 0.49, 2.59 ± 0.68), and control group (0.16 ± 0.09, 0.34 ± 0.18) at both time periods. Alizarin red staining in the Hya-coated PEEK group (1.81 ± 0.23, 1.97 ± 0.20) was significantly greater in comparison with uncoated group (1.12 ± 0.17, 1.14 ± 0.19) and control group (0.99 ± 0.10, 0.98 ± 0.05) at both time intervals.

Conclusion

Hya's surface coating has enhanced the biofunctional properties of PEEK implant material, as demonstrated by improved cell survival, proliferation, differentiation, and mineralization potential.

Analysis of osseointegration of implants with macrogeometries with healing chambers: a randomized clinical trial

BACKGROUND

To verify the influence of macrogeometry with healing chambers on the osseointegration of dental implants by analyzing implant stability quotient (ISQ) and evaluate the correlation between insertion torque and ISQ insertion with different macrogeometries.

METHODS

In total, 26 implants were installed in the posterior mandible of eight patients with sufficient bone height for the installation of implants measuring 3.5 mm in diameter and 9.0 mm in length. The implants were categorized according to two types of macrogeometry: a test group (GT) with 13 conical implants with healing chambers and a control group (GC) with 13 conical implants with conventional threads. To insert the implants, a bone drilling protocol was used up to a diameter of 3 mm with the last helical bur. The insertion torque of the implants was evaluated, followed by the measurement of ISQ at 0 (T-0), 7 (T-7), 14 (T-14), 21 (T-21), 28 (T-28), and 42 (T-42) days.

RESULTS

The mean insertion torque was 43 Ncm in both groups, without a significant difference. Moreover, no significant difference in the ISQ values was found between the groups at different time points (p > 0.05), except at T-7 (GT = 69.87±1.89 and GC = 66.48±4.49; p = 0.01). Although there was no significant difference, ISQ median values were higher in the GT group than GC group at 28 days (GT = 67.98 and GC = 63.46; p = 0.05) and 42 days (GT = 66.12 and GC = 60.33; p = 0.09). No correlation was found between the insertion torque and ISQ insertion (p > 0.05).

CONCLUSION

Furthermore, implants with a 3.5 mm diameter macrogeometry, with or without healing chambers, inserted with a drilling protocol up to 3 mm in diameter of the last helical bur, led to a similar secondary stability, with no difference in ISQ values. Although, implants with healing chamber demonstrates ascending values in the graph of ISQ, having a trend of faster osseointegration than implants without healing chambers. Both macrogeometries provide a similar primary stability to implants.

TRIAL REGISTRATION

This study was registered retrospectively in ReBec (brazilian registry of clinical trials) under the number RBR-96n5×69, on the date of 19/06/2023.

The past forty-three years of dental implantology literature. A global mapping and scientometric analysis

PURPOSE

The aim of this research is to make a scientometric analysis of the dental implantology literature and to present the results in a more understandable way to the reader by visualizing them with maps.

METHODS

The dental implantology literature was accessed through the Web of Science database. Scientometric data was obtained with Citespace 6.1 software, co-citation, clustering analysis, citation burst, and mapping analyzes were performed. Scimago Graphica software was used for additional visualizations.

RESULTS

A total of 35,704 articles were included in the analysis. There were 88,616 authors, 72,333 institutes, 142 countries/regions, and 3,265 journals contributing to the dental implantology literature. The United States was first with 7,334 publications and 225,868 citations. The literature between 1980 and 2023 was divided into 19 different clusters, and the literature between 2000 and 2023 was divided into 16 different clusters.

CONCLUSIONS

Key themes in the field include the use of autogenous bone, advancements in implant surface technology, and the use of platform switching and intraoral scanners. Emerging topics of interest include esthetic considerations in the treatment of the anterior region, stress distribution, the use of zirconia, and the impact of implant treatment on oral health-related quality of life. With similar scientometric analysis studies to be done in the future, the progress of the literature can be followed on the basis of evidence.

A Comprehensive Review of the Contemporary Methods for Enhancing Osseointegration and the Antimicrobial Properties of Titanium Dental Implants

Titanium dental implants with various restorative options are popular for replacing missing teeth due to their comfortable fit, excellent stability, natural appearance, and impressive track record in clinical settings. However, challenges such as potential issues with osseointegration, peri-implant bone loss, and peri-implantitis might lead to implant failure, causing concern for patients and dental staff. Surface modification has the potential to significantly enhance the success rate of titanium implants and meet the needs of clinical applications. This involves the application of various physical, chemical, and bioactive coatings, as well as adjustments to implant surface topography, offering significant potential for enhancing implant outcomes in terms of osseointegration and antimicrobial properties. Many surface modification methods have been employed to improve titanium implants, showcasing the diversity of approaches in this field including sandblasting, acid etching, plasma spraying, plasma immersion ion implantation, physical vapor deposition, electrophoretic deposition, electrochemical deposition, anodization, microarc oxidation, laser treatments, sol-gel method, layer-by-layer self-assembly technology, and the adsorption of biomolecules. This article provides a comprehensive overview of the surface modification methods for titanium implants to address issues with insufficient osseointegration and implant-related infections. It encompasses the physical, chemical, and biological aspects of these methods to provide researchers and dental professionals with a robust resource to aid them in their study and practical use of dental implant materials, ensuring they are thoroughly knowledgeable and well-prepared for their endeavors.

Bovine Mineral Grafting Affects the Hydrophilicity of Dental Implant Surfaces: An In Vitro Study

Wettability is recognized as an important property of implant surfaces for ensuring improved biological responses. However, limited information exists on how bone grafting procedures including materials influence the hydrophilic behavior of implant surfaces. This in vitro study aimed to investigate the influence of two bovine grafting materials after hydration on the wettability of four different disk surfaces: commercially pure titanium (CP-Ti), titanium-zirconium dioxide (TiZrO2-Cerid®), zirconia (SDS®), and niobium. Wettability tests were performed on each of the four implant surfaces with a solution of 0.9% sodium chloride after mixture with W-boneTM (Group A) or Bio-Oss® (Group B) or 0.9% sodium chloride alone (Group C). In total, 360 contact angle measurements were completed with n = 30 per group. Statistical analysis was performed using a one-way analysis with variance (ANOVA) test with a significant mean difference at the 0.05 level. For pure titanium, Group A demonstrated increased hydrophilicity compared to Group B. Both TiZrO2 and zirconia showed significant differences for Groups A, B and C, exhibiting a decrease in hydrophilicity after the use of bovine grafting materials compared to titanium surfaces. Niobium remained consistently hydrophobic. In summary, this study revealed that bovine grafting materials may diminish the hydrophilicity of zirconia surfaces and exert varied effects on titanium and niobium. These findings contribute to the understanding of implant surface interactions with grafting materials, offering insights for optimizing biological responses in implantology.

The regulatory effect of TiO2 nanotubes loaded with graphene oxide on macrophage polarization in an inflammatory environment

BACKGROUND

Excessive inflammation is a major cause of implant failure. The surface morphology, hydrophilicity, and loading of biomaterials are major properties modulating anti-inflammatory macrophage activation. This paper investigates the regulatory effects of modifying the surface of Titanium dioxide nanotubes (TNTs) with graphene oxide (GO) on the polarization of mouse monocyte macrophages (RAW264.7).

METHODS

TNT was produced by the anodic oxidation of titanium. GO was subsequently electrodeposited on the TNT to obtain a TNT-GO composite. The samples were characterised through scanning electron microscopy (SEM), Raman spectroscopy, and X-ray diffraction. RAW264.7 cells were separately seeded onto the surface of three groups of samples: pure Ti, TNT, and TNT-GO. Under the condition of lipopolysaccharide stimulation, the influence of the sample surfaces on the gene expression profiles was investigated through RNA sequence analysis. In addition, cell spreading was observed through SEM, cell adhesion and proliferation were analysed using the CCK8 assay, and the expression of inflammation-related factors was investigated by ELISA and cellular immunofluorescence staining. The production of reactive oxygen species (ROS) in the RAW264.7 cells on the surface of the three groups was detected via immunofluorescence staining.

RESULTS

The CCK8 results indicated that the adhesion and proliferation of the RAW264.7 cells were reduced on the TNT and TNT-GO surfaces. ELISA results revealed significant differences in the pro-inflammatory factors tumour necrosis factor-α and interleukin-6 secretion among the three groups at 24 h (p < 0.05). The secretion of pro-inflammatory factors significantly reduced and the expression of anti-inflammatory factor IL-10 increased on the TNT and TNT-GO surfaces. The RNA sequencing, ELISA, and cell immunofluorescence staining test results suggested that the inflammatory response of M1 polarization was reduced and the M2 polarization of macrophages was induced on the TNT-GO surface, which may be attributed to the reduction in ROS production.

CONCLUSIONS

Under lipopolysaccharide stimulation, the inflammatory response of the RAW264.7 cells was reduced and the M2 polarization of macrophages was promoted on the TNT-GO surface, which may be caused by the reduced ROS production. Consequently, the designed TNT-GO material is promising for implants owing to its excellent inflammation regulation ability.

Surface Topography Has Less Influence on Peri-Implantitis than Patient Factors: A Comparative Clinical Study of Two Dental Implant Systems

OBJECTIVES

This study aims to assess the risk of peri-implantitis (PI) onset among different implant systems and evaluate the severity of the disease from a population of patients treated in a university clinic. Furthermore, this study intends to thoroughly examine the surface properties of the implant systems that have been identified and investigated.

MATERIAL AND METHODS

Data from a total of six hundred and 14 patients were extracted from the Institute of Clinical Dentistry, Dental Faculty, University of Oslo. Subject- and implant-based variables were collected, including the type of implant, date of implant installation, medical records, recall appointments up to 2022, periodontal measurements, information on diabetes, smoking status, sex, and age. The outcome of interest was the diagnosis of PI, defined as the occurrence of bleeding on probing (BoP), peri-implant probing depth (PD) ≥ 5 mm, and bone loss (BL). Data were analyzed using multivariate linear and logistic regression. Scanning electron microscopy, light laser profilometer, and X-ray photoelectron spectroscopy were utilized for surface and chemical analyses.

RESULTS

Among the patients evaluated, 6.8% were diagnosed with PI. A comparison was made between two different implant systems: Dentsply Sirona, OsseospeedTM and Straumann SLActive, with mean follow-up times of 3.84 years (SE: 0.15) and 3.34 years (SE: 0.15), respectively. The surfaces have different topographies and surface chemistry. However, no significant association was found between PI and implant surface/system, including no difference in the onset or severity of the disease. Nonetheless, plaque control was associated with an increased risk of developing PI, along with the gender of the patient. Furthermore, patients suffering from PI exhibited increased BL in the anterior region.

CONCLUSION

No differences were observed among the evaluated implant systems, although the surfaces have different topography and chemistry. Factors that affected the risk of developing PI were plaque index and male gender. The severity of BL in patients with PI was more pronounced in the anterior region. Consequently, our findings show that success in implantology is less contingent on selecting implant systems and more on a better understanding of patient-specific risk factors, as well as on implementing biomaterials that can more effectively debride dental implants.

The Addition of Hydroxyapatite Nanoparticles on Implant Surfaces Modified by Zirconia Blasting and Acid Etching to Enhance Peri-Implant Bone Healing

This study investigated the impact of adding hydroxyapatite nanoparticles to implant surfaces treated with zirconia blasting and acid etching (ZiHa), focusing on structural changes and bone healing parameters in low-density bone sites. The topographical characterization of titanium discs with a ZiHa surface and a commercially modified zirconia-blasted and acid-etched surface (Zi) was performed using scanning electron microscopy, profilometry, and surface-free energy. For the in vivo assessment, 22 female rats were ovariectomized and kept for 90 days, after which one implant from each group was randomly placed in each tibial metaphysis of the animals. Histological and immunohistochemical analyses were performed at 14 and 28 days postoperatively (decalcified lab processing), reverse torque testing was performed at 28 days, and histometry from calcified lab processing was performed at 60 days The group ZiHa promoted changes in surface morphology, forming evenly distributed pores. For bone healing, ZiHa showed a greater reverse torque, newly formed bone area, and bone/implant contact values compared to group Zi (p < 0.05; t-test). Qualitative histological and immunohistochemical analyses showed higher features of bone maturation for ZiHa on days 14 and 28. This preclinical study demonstrated that adding hydroxyapatite to zirconia-blasted and acid-etched surfaces enhanced peri-implant bone healing in ovariectomized rats. These findings support the potential for improving osseointegration of dental implants, especially in patients with compromised bone metabolism.

A Microscopy Evaluation of Emergence Profile Surfaces of Dental Custom CAD-CAM Implant Abutments and Dental Implant Stock Abutments

Recently, due to the high demand for dental implants, the use of dental implant stock abutments has increased significantly, especially dental custom CAD/CAM implant abutments milled by dental technicians in their laboratories. The purpose of this study is to analyze the surface quality of the emergence profile of dental custom CAD/CAM implant abutments made by a non-industrial milling machine, compared to original and compatible dental implant stock abutments made by industrial machines. Thirty dental implant abutments were divided into six study lots. Lot 1 (control group): original dental implant stock abutments-industrial machined; lot 2 (study group): compatible dental implant stock abutments-industrial machined; lots 3, 4, 5, and 6 (study groups): compatible custom CAD/CAM dental implant abutments-non-industrial milled with hyperDENT CAM software and Paragon Tools. The Nikon SMZ745T stereomicroscope was used to analyze the emergence profile surface of each dental implant abutment. The structure of the analyzed surfaces did not show significant differences between original and compatible abutments that were industrially machined. As for the customized dental implant abutments, the greatest similarity with the original was obtained for lot 6, and a significant statistical difference was obtained for lot 4. Stepover and Feed Rate parameters of the milling process influenced the surface roughness of the emergence profile for the customized dental implant abutments. The digital technology of non-industrial milling compatible custom CAD/CAM dental implant abutments is reliable and within the correct milling parameters.

Effect of vertical implant position on marginal bone loss: a randomized clinical trial

OBJECTIVES

One of the most important factors that has influence on dental implants success rate is marginal bone loss. The purpose of this study is to investigate the effect of the implant's vertical position and the soft tissue's thickness on the rate of marginal bone loss of the dental implant.

MATERIALS AND METHODS

In this single-blind randomized clinical trial study, 56 implants placed in the posterior region of mandible of 33 patients (19 women, 14 men) were divided into two groups. The group of crestal (28 implants) and subcrestal (28 implants) implants, each group was divided into two sub-groups with soft tissue thickness of 2 mm and less than 2 mm (14 implants) and more than 2 mm (14 implants). The amount of marginal bone loss was measured by Scanora 5.2 program with radiographs Digital parallelism based on the effect of the vertical position of the implant, soft tissue thickness, three months after placement, and three months after loading implants (six months after implant placement).

RESULTS

The results showed that marginal bone loss in subcrestal implants is significantly more than crestal implants (p-value = 0.001), and also marginal bone loss in the soft tissue thickness group of 2 mm and less is significantly more than the group of soft tissue thickness more than 2 mm (p-value < 0.001). The amount of marginal bone loss three months after implant loading was significantly higher than three months after implant placement (p-value < 0.001).

CONCLUSION

The implant's vertical position and the soft tissue's thickness around the implant are effective factors in the amount of marginal bone loss. Marginal bone loss is more in subcrestal implants and in cases with less soft tissue thickness. The time factor significantly affects the amount of marginal bone loss.

TRIAL REGISTRATION

this clinical trial was registered at Iranian Registry of Clinical Trials, registration number IRCT20120215009014N415, registration date 20,220,110, (https//en.irct.ir/trial/60,991).

Tribocorrosion of 3D printed dental implants: An overview

With the advancements in dental science and the growing need for improved dental health, it has become imperative to develop new implant materials which possess better geometrical, mechanical, and physical properties. The oral environment is a corrosive environment and the relative motion between the teeth also makes the environment more hostile. Therefore, the combined corrosion and tribology commonly known as tribocorrosion of implants needs to be studied. The complex shapes of the dental implants and the high-performance requirements of these implants make manufacturing difficult by conventional manufacturing processes. With the advent of additive manufacturing or 3D-printing, the development of implants has become easy. However, the various requirements such as surface roughness, mechanical strength, and corrosion resistance further make the manufacturing of implants difficult. The current paper reviews the various studies related to3D-printed implants. Also, the paper tries to highlight the role of 3D-Printing can play in the area of dental implants. Further studies both experimental and numerical are needed to devise optimized conditions for 3D-printing implants to develop implants with improved mechanical, corrosion, and biological properties.

Evaluation of Adhesion and Viability of Human Gingival Fibroblasts on Strontium-Coated Titanium Surfaces: an in vitro Study

Background

Applying multifunctional coatings employing strontium (Sr) ions on titanium (Ti) surfaces is a useful and biocompatible method to improve osseointegration and prevent tissue infections through antimicrobial activity. Nonetheless, the effectiveness of Sr coating on the adhesion and viability of human gingival fibroblasts (HGFs) to Ti surfaces remains unclear.

Purpose

The study aimed to evaluate the effect of Sr coating on the adhesion and viability of HGFs to Ti surfaces.

Materials and Methods

The Ti wafers were divided into two groups based on Sr coating: uncoated Ti (control) and Sr-coated Ti. The Magnetron sputtering technique was used for Sr coating on Ti surfaces. The HGFs were seeded onto the surfaces and cultured for 48 and 96 hours before the cell adhesion and viability of the attached HGFs were assessed. The adhesion of HGFs was analyzed using the attached cell numbers at 48 h and 96 h, and the morphology at 24 h and 72 h. The cytotoxic effect on HGFs was assessed after 24 and 72 hours of incubation using cell viability assay. Student's t-test was used for statistical analysis.

Results

The number of cells attached to Sr-coated surfaces was significantly greater than those attached to uncoated Ti surfaces after 48 hours (P<0.0001) and 96 hours (P=0.0002). Sr-coated and uncoated Ti surfaces were not cytotoxic to HGFs, with the cell viability ranging from 92% to 105% of the untreated control HGFs. There were no significant differences in cell viability between Sr-coated and uncoated Ti surfaces at 24 hours (P=0.3675) and 72 hours (P=0.0982).

Conclusion

Sr-coated Ti surfaces induce adhesion of HGFs compared to uncoated Ti surfaces. Further, Sr-coated and uncoated Ti surfaces show no cytotoxic effect on the attached HGFs.

An Innovative Design to Enhance Osteoinductive Efficacy and Biomechanical Behavior of a Titanium Dental Implant

The present study investigated the in vivo bone-forming efficacy of an innovative titanium (Ti) dental implant combined with a collagen sponge containing recombinant human bone morphogenetic protein-2 (BMP-2) in a pig model. Two different concentrations of BMP-2 (20 and 40 µg/mL) were incorporated into collagen sponges and placed at the bottom of Ti dental implants. The investigated implants were inserted into the edentulous ridge at the canine-premolar regions of Lanyu small-ear pigs, which were then euthanized at weeks 1, 2, 4, 8, and 12 post-implantation. Specimens containing the implants and surrounding bone tissue were collected for histological evaluation of their bone-to-implant contact (BIC) ratios and calculation of maximum torques using removal torque measurement. Analytical results showed that the control and BMP-2-loaded implants presented good implant stability and bone healing for all testing durations. After 1 week of healing, the BMP-2-loaded implants with a concentration of 20 µg/mL exhibited the highest BIC ratios, ranging from 58% to 76%, among all groups (p = 0.034). Additionally, they also possessed the highest removal torque values (50.1 ± 1.3 N-cm) throughout the 8-week healing period. The BMP-2-loaded implants not only displayed excellent in vivo biocompatibility but also presented superior osteoinductive performance. Therefore, these findings demonstrate that BMP-2 delivered through a collagen sponge can potentially enhance the early-stage osseointegration of Ti dental implants.

Soft and Hard Tissue Integration around Percutaneous Bone-Anchored Titanium Prostheses: Toward Achieving Holistic Biointegration

A holistic biointegration of percutaneous bone-anchored metallic prostheses with both hard and soft tissues dictates their longevity in the human body. While titanium (Ti) has nearly solved osseointegration, soft tissue integration of percutaneous metallic prostheses is a perennial problem. Unlike the firm soft tissue sealing in biological percutaneous structures (fingernails and teeth), foreign body response of the skin to titanium (Ti) leads to inflammation, epidermal downgrowth and inferior peri-implant soft tissue sealing. This review discusses various implant surface treatments/texturing and coatings for osseointegration, soft tissue integration, and against bacterial attachment. While surface microroughness by SLA (sandblasting with large grit and acid etched) and porous calcium phosphate (CaP) coatings improve Ti osseointegration, smooth and textured titania nanopores, nanotubes, microgrooves, and biomolecular coatings encourage soft tissue attachment. However, the inferior peri-implant soft tissue sealing compared to natural teeth can lead to peri-implantitis. Toward this end, the application of smart multifunctional bioadhesives with strong adhesion to soft tissues, mechanical resilience, durability, antibacterial, and immunomodulatory properties for soft tissue attachment to metallic prostheses is proposed.

Evaluation of High-Performance Polyether Ether Ketone Polymer Treated with Piranha Solution and Epigallocatechin-3-Gallate Coating

Background

Dental implantation has become a standard procedure with high success rates, relying on achieving osseointegration between the implant surface and surrounding bone tissue. Polyether ether ketone (PEEK) is a promising alternative to traditional dental implant materials like titanium, but its osseointegration capabilities are limited due to its hydrophobic nature and reduced surface roughness.

Objective

The aim of the study is to increase the surface roughness and hydrophilicity of PEEK by treating the surface with piranha solution and then coating the surface with epigallocatechin-3-gallate (EGCG) by electrospraying technique.

Materials and Methods

The study includes four groups intended to investigate the effect of piranha treatment and EGCG coating: a control group of PEEK discs with no treatment (C), PEEK samples treated with piranha solution (P), a group of PEEK samples coated with EGCG (E), and a group of PEEK samples treated with piranha solution and coated with EGCG (PE). Surface roughness, wettability, and microhardness were assessed through statistical analysis.

Results

Piranha treatment increased surface roughness, while EGCG coating moderated it, resulting in an intermediate roughness in the PE group. EGCG significantly improved wettability, as indicated by the reduced contact angle. Microhardness increased by about 20% in EGCG-coated groups compared to noncoated groups. Statistical analysis confirmed significant differences between groups in all tests.

Conclusion

This study demonstrates the potential of EGCG coating to enhance the surface properties of PEEK as dental implants. The combined piranha and EGCG modification approach shows promise for improved osseointegration, although further vivo research is necessary. Surface modification techniques hold the key to optimizing biomaterial performance, bridging the gap between laboratory findings and clinical implementation in dental implantology.

Aspirin/amoxicillin loaded chitosan microparticles and polydopamine modified titanium implants to combat infections and promote osteogenesis

It is known that titanium (Ti) implant surfaces exhibit poor antibacterial properties and osteogenesis. In this study, chitosan particles loaded with aspirin, amoxicillin or aspirin + amoxicillin were synthesized and coated onto implant surfaces. In addition to analysing the surface characteristics of the modified Ti surfaces, the effects of the modified Ti surfaces on the adhesion and viability of rat bone marrow-derived stem cells (rBMSCs) were evaluated. The metabolic activities of Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) biofilms on the modified Ti surfaces were also measured in vitro. Moreover, S. aureus was tested for its antibacterial effect by coating it in vivo. Using water as the droplet medium, the contact angles of the modified Ti surfaces increased from 44.12 ± 1.75° to 58.37 ± 4.15°. In comparison to those of the other groups tested, significant increases in rBMSC adhesion and proliferation were observed in the presence of aspirin + amoxicillin-loaded microspheres, whereas a significant reduction in the metabolic level of biofilms was observed in the presence of aspirin + amoxicillin-loaded microspheres both in vitro and in vivo. Aspirin and amoxicillin could be used in combination to coat implant surfaces to mitigate bacterial activities and promote osteogenesis.

A balance of biocompatibility and antibacterial capability of 3D printed PEEK implants with natural totarol coating

OBJECTIVE

Polyetheretherketone (PEEK), a biomaterial with appropriate bone-like mechanical properties and excellent biocompatibility, is widely applied in cranio-maxillofacial and dental applications. However, the lack of antibacterial effect is an essential drawback of PEEK material and might lead to infection and osseointegration issues. This study aims to apply a natural antibacterial agent, totarol coating onto the 3D printed PEEK surface and find an optimized concentration with balanced cytocompatibility, osteogenesis, and antibacterial capability.

METHODS

In this study, a natural antibacterial agent, totarol, was applied as a coating to fused filament fabrication (FFF) 3D printed PEEK surfaces at a series of increasing concentrations (1 mg/ml, 5 mg/ml, 10 mg/ml, 15 mg/ml, and 20 mg/ml). The samples were then evaluated for cytocompatibility with L929 fibroblast and SAOS-2 osteoblast using live/dead staining and CCK-8 assay. The antibacterial capability was assessed by crystal violet staining, live/dead staining, and scanning electron microscopy (SEM) utilizing the oral primary colonizer S. gordonii and isolates of mixed oral bacteria in a stirring system simulating the oral environment. The appropriate safe working concentration for totarol coating is selected based on the results of the cytocompatibility and antibacterial test. Subsequently, the influence on osteogenic differentiation was evaluated by alkaline phosphatase (ALP) and alizarin red staining (ARS) analysis of pre-osteoblasts.

RESULTS

Our results showed that the optimal concentration of totarol solution for promising antibacterial coating was approximately 10 mg/ml. Such surfaces could play an excellent antibacterial role by inducing a contact-killing effect with an inhibitory effect against biofilm development without affecting the healing of soft and hard tissues around FFF 3D printed PEEK implants or abutments.

SIGNIFICANCE

This study indicates that the totarol coated PEEK has an improved antibacterial effect with excellent biocompatibility providing great clinical potential as an orthopedic/dental implant/abutment material.

Effect of TiO2 Abutment Coatings on Peri-Implant Soft Tissue Behavior: A Systematic Review of In Vivo Studies

Establishing a proper soft tissue adhesion around the implant abutment is essential to prevent microbial invasion, inhibit epithelial downgrowth, and obtain an optimal healing process. This systematic review aims to evaluate the real potential of TiO2 coating on the behavior of peri-implant soft tissue health and maintenance. A specific aim was to evaluate clinically and histologically the effect of TiO2 abutment coating on epithelial and connective tissue attachment. Electronic database searches were conducted from 1990 to 2023 in MEDLINE/PubMed and the Web of Science databases. In total, 15 out of 485 publications were included. Eight studies involved humans, and seven were animal studies. Exposure time ranges from 2 days to 5 years. The peri-implant soft tissue evaluations included clinical assessment (plaque index (PI), peri-implant probing pocket depth (PPD), and bleeding on probing (BoP)), histological as well as histomorphometric analysis. The Office of Health Assessment and Translation (OHAT) Risk of Bias Rating Tool for Human and Animal Studies was used to evaluate the overall quality of the studies included in the review. The results showed some variation but remained within acceptable limits. Within the limitations of this systematic review, the present findings suggest that TiO2 coatings seem to influence soft tissue healing. TiO2-coated abutments with a roughness value between 0.2 and 0.5 μm enhance soft tissue health. Sol-gel-derived TiO2 coatings induced better soft tissue attachment than noncoated machined abutment surfaces. The anodized titanium abutments demonstrate comparable clinical and histological outcomes to conventional machined abutments. However, there was variation among the included studies concerning TiO2 coating characteristics and the measured outcomes used to evaluate the soft tissue response, and therefore, quantitative analysis was not feasible. Long-term in vivo studies with standardized soft tissue analysis and coating surface parameters are necessary before a definitive conclusion can be drawn. OSF Registration No.: 10.17605/OSF.IO/E5RQV.

Enhancing Titanium Disk Performance through In-Pack Cold Atmospheric Plasma Treatment

While titanium dental implants have already been clinically established, ongoing research is continuously being conducted to advance the fields of osseointegration and bacterial resistance, seeking further improvements in these areas. In this study, we introduce an innovative method for treating titanium surfaces within tightly sealed packaging. Specifically, titanium discs, enclosed in surgical-grade packaging, underwent treatment using cold atmospheric plasma (CAP). The surfaces were thoroughly characterized in terms of wettability, crystalline structure, and chemical composition. Hemocompatibility analyses were conducted using blood diluted in sodium citrate (1:9) exposed to titanium discs for 30 min inside a CO2 incubator at 37 °C. Subsequently, various blood parameters were evaluated, including prothrombin time (PT), activated partial thromboplastin time (APTT), and platelet adhesion. Microbiological analyses were also performed using Pseudomonas aeruginosa (ATCC 27853) for 4 h at 37 °C. The treatment with CAP Jet resulted in a reduction in contact angle without causing any changes in the crystalline structure. No statistically significant differences were observed in the blood parameters. The plasma-treated samples exhibited lower PT and APTT values compared to those of the control group. The surfaces treated with CAP Jet showed increased platelet activation, platelet density, and thrombus formation when compared with the untreated samples. Moreover, the treated surfaces demonstrated lower bacterial colony formation compared with other surfaces.

Influences of standardized clinical probing on peri-implant soft tissue seal in a situation of peri-implant mucositis: A histomorphometric study in dogs

BACKGROUND

Clinical probing is commonly recommended to evaluate peri-implant conditions. In a situation of peri-implant mucositis or peri-implantitis, the peri-implant seal healing from the disruption of soft tissue caused by probing has not yet been studied. This study aimed to investigate soft tissue healing after standardized clinical probing around osseointegrated implants with peri-implant mucositis in a dog model.

METHODS

Three transmucosal implants in each hemi-mandible of six dogs randomly assigned to the peri-implant healthy group or peri-implant mucositis group were probed randomly in the mesial or distal site as probing groups (PH or PM), the cross-sectional opposite sites as unprobed control groups. Histomorphometric measurements of implant shoulder (IS)-most coronal level of alveolar bone contact to the implant surface (BCI), apical termination of the junctional epithelium (aJE)-BCI, mucosal margin (MM)-BCI, and MM-aJE were performed at 1 day, 1 week, and 2 weeks after probing. Apoptosis, proliferation, proinflammatory cytokines, and matrix metalloproteinases (MMPs) of peri-implant soft tissue were estimated by immunofluorescent analysis.

RESULTS

In the PM group, apical migration of junctional epithelium was revealed by significantly decreased aJE-BCI from 1 day to 2 weeks in comparison to unprobed sites (p < 0.05), while no significant differences were found in the PH group. Immunofluorescent analysis showed higher levels of interleukin-1β (IL-1β), IL-6, tumor necrosis factor-α (TNF-α), MMP-1, and MMP-8, together with exaggerated apoptosis and proliferation of peri-implant soft tissue in the PM group.

CONCLUSION

Within the limitations, standardized clinical probing might lead to apical migration of the junctional epithelium in a situation of peri-implant mucositis.

Fibroblasts and osteoblasts behavior after contact with different titanium surfaces used as implant abutment: An in vitro experimental study

Background

The goal of this in vitro study was to compare three different surfaces: two types of implant surfaces commercially available ([a] smooth/machined and [b] acid-treated surface) versus (c) anodized surface. Discs were manufactured with commercially pure titanium (CP) grade IV, which were subsequently analyzed by scanning microscopy and fibroblastic and osteoblastic cell cultures.

Methods

Ninety-nine discs (5 × 2 mm) were manufactured in titanium grade IV and received different surface treatments: (i) Mach group: machined; (ii) AA group: double acid etch; and (iii) AN group: anodizing treatment. Three discs from each group were analyzed by Scanning Electron Microscopy (SEM) to obtain surface topography images and qualitatively analyzed by EDS. Balb/c 3T3 fibroblasts and pre-osteoblastic cells (MC3T3-E1 lineage) were used to investigate each group's biological response (n = 10/cellular type). The data were compared statistically using the ANOVA one-way test, considered as a statistically significant difference p < 0.05.

Results

The AA group had numerous micropores with diameters between 5 and 10 μm, while nanopores between 1 and 5 nm were measured in the AN group. The EDX spectrum showed a high titanium concentration in all the analyzed samples. The contact angle and wetting tension were higher in the AA, whereas similar results were observed for the other groups. A lower result was observed for base width in the AA, which was higher in the other two groups. The AN showed the best values in the fibroblast cells, followed by Mach and AA; whereas, in the culture of the MC3T3 cells, the result was precisely the opposite (AA > Mach > AN). There was similar behavior for cell adhesion for the test groups (Mach and AN), with greater adhesion of Balb/c 3T3 fibroblasts compared to MC3T3 cells; in the AA group, there was greater adherence for MC3T3 cells compared to Balb/c 3T3 fibroblasts.

Conclusions

The findings suggest that different surface characteristics can produce different biological responses, possibly cell-line dependent. These findings have important implications for the design of implantable medical devices, where the surface characteristics can significantly impact its biocompatibility.

Magnesium promotes vascularization and osseointegration in diabetic states

Diabetes has long been considered a risk factor in implant therapy and impaired wound healing in soft and hard oral tissues. Magnesium has been proved to promote bone healing under normal conditions. Here, we elucidate the mechanism by which Mg2+ promotes angiogenesis and osseointegration in diabetic status. We generated a diabetic mice model and demonstrated the alveolar bone healing was compromised, with significantly decreased angiogenesis. We then developed Mg-coating implants with hydrothermal synthesis. These implants successfully improved the vascularization and osseointegration in diabetic status. Mechanically, Mg2+ promoted the degradation of Kelch-like ECH-associated protein 1 (Keap1) and the nucleation of nuclear factor erythroid 2-related factor 2 (Nrf2) by up-regulating the expression of sestrin 2 (SESN2) in endothelial cells, thus reducing the elevated levels of oxidative stress in mitochondria and relieving endothelial cell dysfunction under hyperglycemia. Altogether, our data suggested that Mg2+ promoted angiogenesis and osseointegration in diabetic mice by regulating endothelial mitochondrial metabolism.

Surface-Mediated Modulation of Different Biological Responses on Anatase-Coated Titanium

Various surface modification strategies are being developed to endow dental titanium implant surfaces with micro- and nano-structures to improve their biocompatibility, and first of all their osseointegration. These modifications have the potential to address clinical concerns by stimulating different biological processes. This study aims to evaluate the biological responses of ananatase-modified blasted/etched titanium (SLA-anatase) surfaces compared to blasted/acid etched (SLA) and machined titanium surfaces. Using unipolar pulsed direct current (DC) sputtering, a nanocrystalline anatase layer was fabricated. In vitro experiments have shown that SLA-anatase discs can effectively promote osteoblast adhesion and proliferation, which are regarded as important features of a successful dental implant with bone contact. Furthermore, anatase surface modification has been shown to partially enhance osteoblast mineralization in vitro, while not significantly affecting bacterial colonization. Consequently, the recently created anatase coating holds significant potential as a promising candidate for future advancements in dental implant surface modification for improving the initial stages of osseointegration.

Clinical efficiency and stability of surface-modified implants: acid modification versus photoactivation

OBJECTIVE

. Aim: To study the stability of surface-modified dental implants, with the usage of sandblasting/acid modification vs. photoactivation.

PATIENTS AND METHODS

Materials and Methods: In the observation were included 164 patients with dental defects. All patients had digital impressions taken by scanning the oral cavity with an intraoral scanner 3Shape TRIOSR. Group A (80 subjects) included implants whose surface was modified with a combination of sandblasting and acid. Group B (84 subjects) - implants after modification with photoactivation. The implant stability quotient was recorded using an Osstell MentorTM device.

RESULTS

Results: The reliable effectiveness of the photoactivation method in complex treatment of the surface of dental implants in improving the stability of fixed dentures in the short and long-term periods of observation was proven. When assessing immediate clinical outcomes, there was no significant difference in the frequency of hyperemia, algesia, hyperthermia, soft tissue edema, regional lymphadenitis, depending on the classical method of treating the implant surface and the complex method with photoactivation. Of the long-term clinical outcomes with classical surface treatment, the absolute risk of implant failure was 1.2%, relative risk - 0,99 [CI%0,96-1,0]. The average value of the implant stability coefficient (ISQ) and the data of the Periotest study at the time of surgery probably did not differ in the observation groups, after 3 months, a higher index was proven in the treatment of the surface by the method of photoactivation and greater stability of the mandibular implants. At the time of implantation, there were no statistically significant differences in implant fixation between the groups, however, during prospective observation in group A, secondary stability indicators based on periotestometry results were significantly lower.

CONCLUSION

Conclusions: It was proved the reliable effectiveness of the photoactivation-method for surface modification in the short and long-term periods of observation for improving the results of orthodontically treatment.

Layer-by-Layer Deposition of Regenerated Silk Fibroin─An Approach to the Surface Coating of Biomedical Implant Materials

Biomaterials and coating techniques unlock major benefits for advanced medical therapies. Here, we explored layer-by-layer (LbL) deposition of silk fibroin (SF) by dip coating to deploy homogeneous films on different materials (titanium, magnesium, and polymers) frequently used for orthopedic and other bone-related implants. Titanium and magnesium specimens underwent preceding plasma electrolytic oxidation (PEO) to increase hydrophilicity. This was determined as surface properties were visualized by scanning electron microscopy and contact angle measurements as well as Fourier transform infrared spectroscopy (FTIR) analysis. Finally, biological in vitro evaluations of hemocompatibility, THP-1 cell culture, and TNF-α assays were conducted. A more hydrophilic surface could be achieved using the PEO surface, and the contact angle for magnesium and titanium showed a reduction from 73 to 18° and from 58 to 17°, respectively. Coating with SF proved successful on all three surfaces, and coating thicknesses of up to 5.14 μm (±SD 0.22 μm) were achieved. Using FTIR analysis, it was shown that the insolubility of the material was achieved by post-treatment with water vapor annealing, although the random coil peak (1640-1649 cm-1) and the α-helix peak (at 1650 cm-1) were still evident. SF did not change hemocompatibility, regardless of the substrate, whereas the PEO-coated materials showed improved hemocompatibility. THP-1 cell culture showed that cells adhered excellently to all of the tested material surfaces. Interestingly, SF coatings induced a significantly higher amount of TNF-α for all materials, indicating an inflammatory response, which plays an important role in a variety of physiological processes, including osteogenesis. LbL coatings of SF are shown to be promising candidates to modulate the body's immune response to implants manufactured from titanium, magnesium, and polymers. They may therefore facilitate future applications for bioactive implant coatings. However, further in vivo studies are needed to confirm the proposed effects on osteogenesis in a physiological environment.

Investigation of nanotopography on SOCE mediated cell migration via live-cell : Imaging on opaque implant surface

The exploration of cell response to nanotopography has attracted considerable attentions for years. This article focuses on the influence of nanotopography on the intracellular Ca2+ dynamics, the most ubiquitous but ignored second messenger. The classic titanium nanotubes (NT) were fabricated by anodization to formulate nanoporous surfaces. Firstly, the store operative calcium entry (SOCE) in endoplasmic reticulum (ER) and functional Ca2+ release-activated Ca2+ (CRAC) channels were significantly enhanced on NT surfaces that revealed by live-cell Ca2+ imaging and fluorescence resonance energy transfer (FRET) identification of orai1-stim1 connection. To investigate the potential implication of Ca2+ elevation, the dynamic cell migration trajectory was monitored by a self-made holder, which could not only be suitable for the opaque implant surface but also guarantee the focus fields identical during samples shifting. The cell migration on NT surface was more vigorous and rapid, which was correlated with higher focal adhesion proteins expression, Ca2+-dependent calpain activity and stim1 level. In conclusion, this study has confirmed the novel ER Ca2+ hemostasis pathway on nanosurfaces and its crucial role in cell migration regulation, which may help for more biofavorable implant surface design.

Preparation of Thin Films Containing Modified Hydroxyapatite Particles and Phospholipids (DPPC) for Improved Properties of Biomaterials

The main aims of thin biofilm synthesis are to either achieve a new form to promote the transport of drugs in oral delivery systems or as a coating to improve the biocompatibility of the implant's surface. In this study, the Langmuir monolayer technique was employed to obtain films containing Mg-doped hydroxyapatite with 0.5%, 1.0%, and 1.5% Mg(II). The obtained modified HA particles were analysed via the FT-IR, XRD, DLS, and SEM methods. It was shown that the modified hydroxyapatite particles were able to form thin films at the air/water interface. BAM microscopy was employed to characterized the morphology of these films. In the next step, the mixed films were prepared using phospholipid (DPPC) molecules and modified hydroxyapatite particles (HA-Mg(II)). We expected that the presence of phospholipids (DPPC) in thin films improved the biocompatibility of the preparing films, while adding HA-Mg(II) particles will promote antibacterial properties and enhance osteogenesis processes. The films were prepared in two ways: (1) by mixing DPPC and HA-Mg (II) and spreading this solution onto the subphase, or (2) by forming DPPC films, dropping the HA-Mg (II) dispersion onto the phospholipid monolayer. Based on the obtained π-A isotherms, the surface parameters of the achieved thin films were estimated. It was observed that the HA-Mg(II) films can be stabilized with phospholipid molecules, and a more stable structure was obtained from films synthesied via method (2).

In Vivo Studies of Medical Implants for Maxillofacial Surgery Produced from Nanostructured Titanium

This paper presents the results of comprehensive in vivo studies into the osseointegration behavior of medical implants for maxillofacial surgery produced from nanostructured grade 4 titanium. Special attention is given to the phenomenology of bone tissue formation with consideration of its surface relief features and to evaluating the quantitative parameters of the morphological indicators of osteoblast and endothelial cells in the osseointegration zone. These parameters were compared with their measurement data for standard factory-made implants, and considerable acceleration in the fixation of nanotitanium implants due to osseointegation was found. The obtained results indicate a better osseointegration of implants made of nanotitanium in comparison to similar standard products.

Nano-topographical surface engineering for enhancing bioactivity of PEEK implants (in vitro-histomorphometric study)

OBJECTIVES

Dental implants are currently becoming a routine treatment decision in dentistry. Synthetic polyetheretherketone (PEEK) polymer is a prevalent component of dental implantology field. The current study aimed to assess the influence of Nd:YAG laser nano-topographical surface engineering combined with ultraviolet light or platelet rich fibrin on the bioactivity and osseointegration of PEEK implants in laboratory and animal testing model.

MATERIALS AND METHODS

Computer Aided Design-Computer Aided Manufacturing (CAD CAM) discs of PEEK were used to fabricate PEEK discs (8 mm × 3 mm) N = 36 and implant cylinders (3 mm × 6 mm) N = 72. Specimens were exposed to Nd:YAG laser at wavelength 1064 nm, and surface roughness topography/Ra parameter was recorded in nanometer using atomic force microscopy. Laser modified specimens were divided into three groups: Nd:YAG laser engineered surfaces (control), Nd:YAG laser/UV engineered surfaces and Nd:YAG laser/PRF engineered surfaces (N = 12 discs-N = 24 implants). In vitro bioactivity test was performed, and precipitated apatite minerals were assessed with X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). In vivo histomorphometric analysis was performed in rabbits with BIC% calculation.

RESULTS

Ra mean value of PEEK laser engineered surfaces was 125.179 nm. For the studied groups, XRD patterns revealed distinctive peaks of different apatite minerals that were demonstrated by SEM as dispersed surface aggregations. There was a significant increase in the BIC% from control group 56.43 (0.97) to laser/UV surfaces 77.30 (0.78) to laser/PRF 84.80 (1.29) (< 0.0001).

CONCLUSIONS

Successful engineered nano-topographical biomimetic PEEK implant could be achieved by Nd:YAG laser technique associated with improving bioactivity. The combination with UV or PRF could be simple and economic methods to gain more significant improvement of PEEK implant surface bioactivity with superior osteointegration.

Synergistic Enhancement of Protein Recruitment and Retention via Implant Surface Microtopography and Superhydrophilicity in a Computational Fluid Dynamics Model

The exact mechanisms by which implant surface properties govern osseointegration are incompletely understood. To gain insights into this process, we examined alterations in protein and blood recruitment around screw implants with different surface topographies and wettability using a computational fluid dynamics (CFD) model. Compared with a smooth surface, a microrough implant surface reduced protein infiltration from the outer zone to the implant thread and interface zones by over two-fold. However, the microrough implant surface slowed blood flow in the interface zone by four-fold. As a result, compared with the smooth surface, the microrough surface doubled the protein recruitment/retention index, defined as the mass of proteins present in the area per unit time. Converting implant surfaces from hydrophobic to superhydrophilic increased the mass of protein infiltration 2-3 times and slowed down blood flow by up to two-fold in the implant vicinity for both smooth and microrough surfaces. The protein recruitment/retention index was highest at the implant interface when the implant surface was superhydrophilic and microrough. Thus, this study demonstrates distinct control of the mass and speed of protein and blood flow through implant surface topography, wettability, and their combination, significantly altering the efficiency of protein recruitment. Although microrough surfaces showed both positive and negative impacts on protein recruitment over smooth surfaces, superhydrophilicity was consistently positive regardless of surface topography.

Surface modification of titanium implants with Mg-containing coatings to promote osseointegration

Titanium (Ti) and Ti alloys are commonly used in dental implants, which have good biocompatibility, mechanical strength, processability, and corrosion resistance. However, the surface inertia of Ti implants leads to delayed integration of Ti and new bone, as well as problems such as aseptic loosening and inadequate osseointegration. Magnesium (Mg) ions can promote bone regeneration, and many studies have used Mg-containing materials to modify the Ti implant surface. This systematic review summarizes the methods, effects, and clinical applications of surface modification of Ti implants with Mg-containing coatings. Database collection was completed on Janury 1, 2023, and a total of 29 relevant studies were ultimately included. Mg can be compounded with different materials and coated to the surface of Ti implants using different methods. In vitro and in vivo experiments have shown that Mg-containing coatings promote cell adhesion and osteogenic differentiation. On the one hand, the surface roughness of implants increases with the addition of Mg-containing coatings, which is thought to have an impact on the osseointegration of the implant. On the other hand, Mg ions promote cell attachment through binding interactions between the integrin family and FAK-related signaling pathways. And Mg ions could induce osseointegration by activating PI3K, Notch, ERK/c-Fos, BMP-4-related signaling pathways and TRPM7 protein channels. Overall, Mg-based coatings show great potential for the surface modification of Ti implants to promote osseointegration. STATEMENT OF SIGNIFICANCE: The inertia surface of titanium (Ti) implants leads to delayed osseointegration. Magnesium (Mg) ions, known for promoting bone regeneration, have been extensively studied to modify the surface of Ti implants. However, no consensus has been reached on the appropriate processing methods, surface roughness and effective concentration of Mg-containing coatings for osseointegration. This systematic review focus on the surface modification of Ti implants with Mg-containing compounds, highlighting the effects of Mg-containing coatings on the surface properties of Ti implants and its associated mechanisms. Besides, we also provide an outlook on future directions to promote the clinical application of Mg-modified implants.

Influence of Surface Contaminants and Hydrocarbon Pellicle on the Results of Wettability Measurements of Titanium

Hydrophilicity/hydrophobicity-or wettability-is a key surface characterization metric for titanium used in dental and orthopedic implants. However, the effects of hydrophilicity/hydrophobicity on biological capability remain uncertain, and the relationships between surface wettability and other surface parameters, such as topography and chemistry, are poorly understood. The objective of this study was to identify determinants of surface wettability of titanium and establish the reliability and validity of the assessment. Wettability was evaluated as the contact angle of ddH2O. The age of titanium specimens significantly affected the contact angle, with acid-etched, microrough titanium surfaces becoming superhydrophilic immediately after surface processing, hydrophobic after 7 days, and hydrorepellent after 90 days. Similar age-related loss of hydrophilicity was also confirmed on sandblasted supra-micron rough surfaces so, regardless of surface topography, titanium surfaces eventually become hydrophobic or hydrorepellent with time. On age-standardized titanium, surface roughness increased the contact angle and hydrophobicity. UV treatment of titanium regenerated the superhydrophilicity regardless of age or surface roughness, with rougher surfaces becoming more superhydrophilic than machined surfaces after UV treatment. Conditioning titanium surfaces by autoclaving increased the hydrophobicity of already-hydrophobic surfaces, whereas conditioning with 70% alcohol and hydrating with water or saline attenuated pre-existing hydrophobicity. Conversely, when titanium surfaces were superhydrophilic like UV-treated ones, autoclaving and alcohol cleaning turned the surfaces hydrorepellent and hydrophobic, respectively. UV treatment recovered hydrophilicity without exception. In conclusion, surface roughness accentuates existing wettability and can either increase or decrease the contact angle. Titanium must be age-standardized when evaluating surface wettability. Surface conditioning techniques significantly but unpredictably affect existing wettability. These implied that titanium wettability is significantly influenced by the hydrocarbon pellicle and other contaminants inevitably accumulated. UV treatment may be an effective strategy to standardize wettability by making all titanium surfaces superhydrophilic, thereby allowing the characterization of individual surface topography and chemistry parameters in future studies.