Occurrence and fate of benzotriazoles UV filters in a typical residential wastewater treatment plant in Harbin, China

Occurrence, seasonal variations, and fate of household and personal care chemicals in a wastewater treatment plant with Bacillus bioreactor process

Household and personal care chemicals (HPCCs) constitute a significant component of everyday products, with their global usage on the rise. HPCCs are eventually discharged into municipal wastewater treatment plants (WWTPs). However, the behaviors of HPCCs inside the Bacillus Bioreactor (BBR) process, including their prevalence, fate, and elimination mechanisms, remain underexplored. Addressing this gap, our study delves into samples collected from a BBR process at a significant WWTP in the northeast of China. Our results spotlight the dominance of linear alkylbenzene sulfonates (LASs) in the influent with concentrations ranging between 238 and 789 μg/L, much higher than the other HPCC concentrations, and remained dominant in the subsequent treatment units. After treatment using the BBR process, the concentrations of HPCCs in the effluent were diminished. Examination of different treatment units underscores the grit chamber removed over 60% of higher-concentration HPCCs, while the performance of the (RBC) tank needs to be improved. Except for the ultraviolet radiation (UV)-filters, seasonal variations exert minimal impact on the concentrations and removal efficiencies of other HPCCs in the BBR process. According to the mass balance analysis, the important mechanisms for HPCC removal were biodegradation and sludge adsorption. Also, the octocrylene (OCT) concerns raised by the environmental risk assessment of the HPCCs residuals in the final effluent, indicate a moderate risk to the surrounding aquatic environment (0.1 < RQ < 1), whereas other HPCCs have a lower risk level (RQ < 0.1). Overall, the research offers new perspectives on the fate and elimination mechanisms of HPCCs throughout the BBR process.

Occurrence and fate of pharmaceuticals and personal care products in a wastewater treatment plant with Bacillus bio-reactor treatment

Pharmaceuticals and personal care products (PPCPs) have attracted wide attention due to their environmental impacts and health risks. PPCPs released through wastewater treatment plants (WWTPs) are estimated to be 80 %. Nevertheless, the occurrence of PPCPs in the WWTPs equipped with Bacillus spec.-based bioreactors (BBR) treatment system remains unclear. In this study, sludge and waste water samples were collected during separate winter and summer sampling campaigns from a typical BBR treatment system. The results indicate that out of 58 target PPCPs, 27 compounds were detected in the waste water (0.06-1900 ng/L), and 23 were found in the sludge (0.6-7755 ng/g dw). Paraxanthine was the chemical of the highest abundance in the influent due to the high consumption of the parent compounds caffeine and theobromine. The profile for PPCPs in the wastewater and sludge exhibited no seasonal variation. Overall, the removal of target PPCPs in summer is more effective than the winter. In the BBR bio-reactor, it was found that selected PPCPs (at ng/L level) can be completely removed. The efficiency for individual PPCP removal was increased from 1.0 % to 50 % in this unit, after target specific adjustments of the process. The effective removal of selected PPCPs by the BBR treatment system is explained by combined sorption and biodegradation processing. The re-occurrence of PPCPs in the wastewater was monitored. Negative removal efficiency was explained by the cleavage of Phase II metabolites after the biotransformation process, and the lack of equilibrium for PPCPs in the sludge of the second clarifier. A compound specific risk quotient (RQ) was calculated and applied for studying the potential environmental risks. Diphenhydramine is found with the highest environmental risk in wastewater, and 15 other PPCPs show negligible risks in sewage sludge.

Spatiotemporal variation, partitioning, and ecological risk assessment of benzothiazoles, benzotriazoles, and benzotriazole UV absorbers in the Yangtze River Estuary and its adjacent area

The distributions and toxicities of the pollutants benzothiazoles (BTHs), benzotriazoles (BTRs), and benzotriazole ultraviolet stabilizers (BUVs) have attracted much attention, but most research has focused on freshwater environments and few have examined their levels in marine environments. This study, for the first time, investigated the spatial and temporal variability and ecological risks of BTHs, BTRs and BUVs in the Yangtze River estuary and its adjacent area, and further elucidated how environmental factors influence the transport of these contaminants. The concentrations of BTHs, BTRs, and BUVs in seawater showed significant seasonal variability, with the highest concentrations in summer, followed by autumn, and then winter-spring. The spatiotemporal variability in BTHs, BTRs and BUVs in the seawater and sediments samples showed decreasing trends from nearshore to offshore, reflecting the influence of river discharge. Marine debris and continuous discharge from cities were responsible for the high detection frequency of these contaminants in the YRE and its adjacent area. Furthermore, the moderate risk from the presence of BTHs, BTRs, and BUVs as they accumulate in sediments should not be ignored. Our study provides new insights into the fate and ecological risk of BTHs, BTRs, and BUVs in the estuary.

Neurotoxicity of Benzotriazole Ultraviolet Stabilizers in Teleost Fishes: A Review

Plastic additives that maintain integrity have been extensively studied for potential toxicity to fish; however, chemicals that protect polymers from (artificial) UV degradation are less studied. Benzotriazole UV stabilizers (BUVSs) are the most widely used UV stabilizers in plastics and are often used in sunscreens, cosmetics, paint, and food packaging. BUVSs can negatively affect aquatic wildlife when released into the environment via plastic degradation. In this review, we summarize the distribution of BUVSs globally and discuss neurotoxicological endpoints measured in fish to understand how these plastic additives can affect the neurological health of teleost fishes. BUVSs have been detected in aquatic environments at concentrations ranging from 0.05 up to 99,200 ng/L. Studies show that BUVSs affect behavioral responses and acetylcholinesterase activity, indicators of neurotoxicity. Our computational analysis using transcriptome data suggests certain pathways associated with neurodegeneration are responsive to exposure to BUVSs, like "Complement Activation in Alzheimer's Disease". Based on our review, we identify some research needs for future investigations: (1) molecular studies in the central nervous system to define precise mechanisms of neurotoxicity; (2) a wider range of tests for assessing aberrant behaviors given that BUVSs can affect the activity of larval zebrafish; and (3) histopathology of the nervous system to accompany biochemical analyses. These data are expected to enhance understanding of the neurotoxicity potential of benzotriazoles and other plastic additives.

Multimodal Model to Predict Tissue-to-Blood Partition Coefficients of Chemicals in Mammals and Fish

Tissue-to-blood partition coefficients (Ptb) are key parameters for assessing toxicokinetics of xenobiotics in organisms, yet their experimental data were lacking. Experimental methods for measuring Ptb values are inefficient, underscoring the urgent need for prediction models. However, most existing models failed to fully exploit Ptb data from diverse sources, and their applicability domain (AD) was limited. The current study developed a multimodal model capable of processing and integrating textual (categorical features) and numerical information (molecular descriptors/fingerprints) to simultaneously predict Ptb values across various species, tissues, blood matrices, and measurement methods. Artificial neural network algorithms with embedding layers were used for the multimodal modeling. The corresponding unimodal models were developed for comparison. Results showed that the multimodal model outperformed unimodal models. To enhance the reliability of the model, a method considering categorical features, weighted molecular similarity density, and weighted inconsistency in molecular activities of structure-activity landscapes was used to characterize the AD. The model constrained by the AD exhibited better prediction accuracy for the validation set, with the determination coefficient, root mean-square error, and mean absolute error being 0.843, 0.276, and 0.213 log units, respectively. The multimodal model coupled with the AD characterization can serve as an efficient tool for internal exposure assessment of chemicals.

Benzotriazole UV stabilizers (BUVs) as an emerging contaminant of concern: a review

Benzotriazole UV stabilizers (BUVs) are a group of industrial chemicals used in various consumer products and industrial applications. Due to its large-scale production and use, BUVs have been detected in all environmental matrices. Humans are exposed to BUVs from environmental media, food, personal care products (PCPs), and consumer products. As a result, BUVs are detected in human breast milk, attracting researchers and regulatory bodies worldwide. BUVs such as UV-328 exhibit the characteristics of persistent organic pollutants (POPs); hence, it has been recently listed under Stockholm Convention POP list. The current review focuses on the occurrence of BUVs in the environment with emphasis on persistency, bioaccumulation, and toxicity (PBT). Scarcity of scientific data on BUVs' properties, environmental occurrence, exposure levels, and effects on organisms poses significant challenges to the policymakers and regulatory bodies in adopting management strategies. The need for a science-based integrated framework for risk assessment and management of BUVs is recommended. Considering the potential threat of BUVs to human health and the environment, it is recommended that BUVs should be taken as a subject of priority research. Studies on the degradation and transformation route of BUVs need to be explored for the sound management of BUVs.

Peroxymonosulfate Activation by Cu-OMS-2 Nanofibers for Efficient Degradation of N-Containing Heterocycles in Aquatic Solution

In this research, the degradation of different types of N-containing heterocycle (NHC) contaminants by Cu-OMS-2 via peroxymonosulfate (PMS) activation in an aqueous environment was investigated. First, the effects of different reaction parameters were optimized using benzotriazole (BTR) as the model contaminant, and the optimal reaction conditions were 8 mM PMS, 0.35 g/L Cu-OMS-2, and 30 °C. Nine different types of NHC contaminants were effectively degraded under these reaction conditions, and the degradation efficiencies and the mineralization rates of those NHCs were more than 68 and 46%, respectively. Moreover, the Cu-OMS-2/PMS process presented excellent performance at a wide pH ranging from 3.0 to 11.0 and in the presence of some representative anions (NO3- and SO42-) and dissolved organic matter (fumaric acid). The inhibition sequence of anions on BTR removal during the Cu-OMS-2/PMS process was H2PO4- > HCO3- > Cl- > CO32- > NO3- > SO42-. It was also found that 74.5 and 71.3% BTR degradation rates were achieved in actual water bodies, such as tap water and Yellow River water, respectively. Besides, the Cu-OMS-2 heterogeneous catalyst had excellent stability and reusability, and the degradation rate of BTR was still at 77.0% after 5 cycles. Finally, electron paramagnetic resonance analysis and scavenging tests showed that 1O2 and SO4- • were the primary reactive oxygen species. Accordingly, Cu-OMS-2 nanomaterial was an efficient and sustainable heterogeneous catalyst to activate PMS for the decontamination of BTR in water remediation.

New insight into the removal process of benzotriazole UV stabilizers by UV/H2O2: Integrating quantum chemical calculation with CFD simulation

Benzotriazole UV stabilizers (BT-UVs) are important UV absorbers. As high-production chemicals and potential hazards, their ubiquitous presence in aquatic environments is of greatly pressing concern. Herein, the removal of six typical BT-UVs by UV/H2O2 was comprehensively investigated by quantum chemistry calculation integrated with CFD simulation. Utilizing such a micro and macro incorporated model in treating contaminants is the first report. From the micro-view, degradation mechanisms of BT-UVs by •OH oxidation were determined, and corresponding rate constants were obtained with values of 109∼1010 M-1s-1. In a macroscopic aspect, combining the established kinetic model and CFD simulation, the effects of UV lamp power (P), volumetric flow rate (Qv), and H2O2 dosage ([H2O2]0) on removal yields of BT-UVs were expounded, increasing P or [H2O2]0 or decreasing Qv are effective in improving removal yields of BT-UVs, but the enhancement was abated when P or [H2O2]0 increased to a certain level. When [H2O2]0 is 5 mg/L and Qv is decreased from 0.1 to 0.05 m3/h, the removal yields of BT-UVs could achieve more than 95% (P = 150 W) and 99% (P = 250 W), respectively. This work provides a new interdisciplinary insight for investigating organic contaminant removal in potential industrial applications of UV/H2O2 systems.

Tracking contaminants of concern in wet-weather sanitary sewer overflows

Four representative sites in the greater city of Sydney, Australia, were selected for a study of the wet-weather overflow of sanitary (separate to stormwater) sewerage systems. Water samples were collected by autosamplers from up to eight wet weather overflow events over 16 months and from companion receiving water sites. The objective was to identify the risks posed by sewage contaminants to aquatic biota in the receiving waters, to aid in prioritising management actions. Twelve organic contaminants were identified in influents across the four sites under rainfall ingress diluted conditions, with measurements showing that the highest concentrations were restricted to the anti-inflammatory acetaminophen and the diabetes medication metformin. Lesser contaminants included theobromine, ibuprofen, sucralose, and three benzotriazoles (mainly 1-H benzotriazole). An assessment of the toxicity of the identified organic chemicals indicated that none appeared to pose concerns for ecosystem health before wet-weather ingress dilution, and this was even less likely after dilution in the receiving waters. Metal concentrations were low; however, ammonia concentrations in the influent did pose a risk to ecosystem health, although receiving water dilution diminished this risk at four of the five receiving water locations studied.

Occurrence, spatio-temporal variation and ecological risk assessment of benzotriazole ultraviolet stabilizers (BUVs) in water and sediment of rivers in central India

Occurrence of benzotriazole ultraviolet stabilizers (BUVs) in different environmental matrices has attracted researchers and regulatory agencies worldwide due to its persistency, bioaccumulative and toxic properties. Environmental occurrence of BUVs in Indian freshwater is lacking. The present study analyzed six targeted BUVs in surface water and sediments of three rivers of Central India. BUVs were determined in pre- and post-monsoon seasons to reveal their concentration, spatio-temporal distribution and probable ecological risks. Results indicated that total concentration of BUVs (ƩBUVs) ranged from ND to 42.88 μg/L in water, and ND to 165.26 ng/g in sediments with UV-329 as the predominant BUV in surface water and sediments during pre- and post-monsoon seasons. Surface water samples from Pili River, and sediment of Nag River accounted for maximum BUVs concentration. Partitioning coefficient results confirmed the effective transfer of BUVs from overlaying water to sediments. The observed concentration of BUVs in water and sediments posed low ecological risk to planktons. Untreated municipal discharges and poor waste management practices including dumping of wastes might be the sources of BUVs in water bodies.

Simultaneous determination of benzothiazoles, benzotriazoles, and benzotriazole UV absorbers by solid-phase extraction-gas chromatography-mass spectrometry

Benzotriazoles (BTRs), benzothiazoles (BTHs), and benzotriazole ultraviolet absorbers (BUVs) are common products in plastic rubber and personal care products. Due to their toxicity and bioaccumulation, they have been identified as emerging contaminants (ECs) in the environment. Solid-phase microextraction (SPME) and solid-phase extraction (SPE) combined with gas chromatography-mass spectrometry (GC-MS) were used for the enrichment and detection of the contaminants in seawater and sediment, respectively. The conditions of SPE and SPME were optimized in terms of material, temperature, time, pH, ionic strength, extraction solvent, and elution solvent. Although SPME requires a small sample volume, it is not reliable for the extraction efficiency and reproducibility of BTHs, BTRs, and BUVs in seawater. However, the precision of SPE-GC-MS for the determination of BTHs, BTRs, and BUVs was around 10%, with recoveries of 67.40-102.3% and 77.35-101.8% in seawater and sediment, respectively. The limits of detection of 14 contaminants in seawater and sediment were 0.03-0.47 ng/L and 0.01-0.58 ng/g, respectively. Secondly, BTHs, BTRs, and BUVs were detected with low ecological risk when SPE-GC-MS was applied to the analysis of seawater and sediment samples from the Yangtze estuary and its adjacent areas. The SPE-GC-MS was highly precise with lower detection limits relative to previous studies and thus was able to meet the requirements for the detection of BTHs, BTRs, and BUVs in seawater and sediments.

Occurrence and removal of benzotriazole and benzothiazole in drinking water treatment plants

The occurrence and removal of four benzotriazoles (BTRs) and five benzothiazoles (BTHs) in drinking water treatment plants (DWTPs) and bottled water were investigated. The mean total BTR and BTH concentrations were 390 and 117 ng/L in raw water, 51.2 and 66.5 ng/L in treated water, and 0.758 and 48.4 ng/L in bottled water, respectively. Different distribution patterns were observed according to the water type, with the dominant BTR being 1H-BTR (mean: 57.8%) in raw water and a predominance of BTH in bottled water (mean: 84.6%). In the DWTPs, the mean removal of BTRs (90.9%) was better than that of BTHs (29.3%). The BTRs were efficiently removed in DWTPs, and in particular during adsorption processes. 5Cl-BTR had a high removal efficiency (75.7%) in the adsorption processes, followed by 5M-BTR (70.0%), 5,6-di-MeBTR (58.4%), and 1H-BTR (50.1%). By contrast, BTHs were not efficiently removed in DWTPs, although relatively high removal efficiencies were achieved with an ozonation process (43.1%) compared to other treatment processes. In treated drinking and bottled water, the hazard quotients (HQs) of the representative BTRs and BTHs were acceptable (defined as HQ < 1), with a safety margin of 2-5 orders of magnitude.

Aquatic environmental fates and risks of benzotriazoles, benzothiazoles, and p-phenylenediamines in a catchment providing water to a megacity of China

Wearing of vehicle parts could release many chemical additives into the environment, such as benzotriazoles (BTRs), benzothiazoles (BTHs), and p-phenylenediamines (PPDs), which are potentially toxic to wildlife and humans. This study investigated the occurrence, source, and risks of BTRs, BTHs, and PPDs in a source catchment providing water to Guangzhou, a megacity in South China, covering groundwater, surface water, and stormwater. The results showed that BTRs and BTHs were predominant in surface water and groundwater. Unexpectedly, the BTR and BTH concentrations were lower in surface water than groundwater in a third of the paired samples. For the first time, 6PPD-quinone, a toxic ozonation product of N-(1,3-dimethylbutyl)-N'-phenyl-1,4-phenylenediamine (6PPD), was extensively detected in source waters. Stormwater decreased the BTR concentrations but increased the 6PPD-quinone concentrations in surface water owing to their affiliation to suspended particles. From natural to urban segments of Liuxi river, a downstream increasing trend in BTR and BTH concentrations was observed, confirming that they are indicative of urban anthropogenic activities. Strong correlations between industrial activities and BTR or BTH concentrations in surface water indicated that industrial activities were their main sources. Six compounds were prioritized as potentially persistent, mobile, and toxic (PMT) chemicals, combing our monitoring results and REACH criterion. This study improves our understanding of the environmental fates and risks of water-soluble tire-wear chemicals, which provides important information for chemical management, and indicates attention should be paid to the risk posed by 6PPD-quinone in the source water.

Determination of UV Filters in Waste Sludge Using QuEChERS Method Followed by In-Port Derivatization Coupled with GC-MS/MS

UV filters (UVFs) are widely used in personal care and in industrial products for protection against photodegradation. In recent years, their potential toxicological and environmental effects have received growing attention. Due to their excessive use, their residue levels in the environment are gradually increasing and they tend to accumulate on biological wastewater treatment sludge. The utilization of sludge as fertilizer could be one of the main routes of UVF contamination in the environment. Therefore, the development of a reliable and sensitive method of analyzing their trace level residues in waste sludge samples is of great importance. The success of the method largely depends on the sample preparation technique in such complex matrices. This study presents a rapid, sensitive and green analysis method for eight UVFs in sludge samples, selected for their rather low no-observed-effect concentrations (NOEC). For this purpose, the QuEChERS methodology was coupled with in-port derivatization for subsequent detection of the targeted UVFs via GC−MS/MS. The analysis time was substantially shortened using this method, and reagent utilization was also reduced. The method was validated in the sludge samples, and high recovery (66−123%) and low RSD values (<25.6%) were obtained. In addition, major contributing uncertainty sources and expanded uncertainties were determined.

Contaminants of emerging concern in marine areas: First evidence of UV filters and paraben preservatives in seawater and sediment on the eastern coast of Tunisia

UV filters (UVFs) and paraben preservatives (PBs) are widely used components in many personal care products. However, there has been a rising concern for their endocrine-disrupting effects on wildlife once they reach aquatic ecosystems via recreative activities and wastewater treatment plants effluents. This study addresses UVFs and PBs occurrence in seawater and sediment impacted by tourism and sewage discharges along the coast of Mahdia, center East Tunisia. Samples of water and sediment were collected for 6 months from 3 coastal areas. Among the 14 investigated UVFs, 8 were detected in seawater and 4 were found in sediment. All PBs were present in seawater and only methylparaben (MePB) was detected in sediment. Benzophenone-3 (oxybenzone, BP3), benzocaine (EtPABA), and MePB were present in all water samples with concentrations in the ranges 16.4-66.9, 7.3-37.7, and 17.6-222 ng/L, respectively. However, the highest value, 1420 ng/L, corresponded to octinoxate (EHMC). In sediments, avobenzone (AVO), 4-methyl benzylidene camphor (4MBC), EHMC, 5-methyl-1-H-benzotriazole (MeBZT), and MePB were detected at concentrations within the range 1.1-17.6 ng/g dw, being MePB the most frequently detected (89%). MePB and MBZT presented the highest sediment-water partition coefficients and MePB also showed a positive correlation with total suspended solids' water content. Overall, pollutants concentrations remained rather constant along the sampling period, showing little seasonal variation. This study constitutes the first monitoring of UVFs and PBs on the Tunisian coastline and provides occurrence data for reference in further surveys in the country.

Bioassay-based identification and removal of target and suspect toxicants in municipal wastewater: Impacts of chemical properties and transformation

Municipal wastewater contains numerous chemicals and transformation products with highly diverse physiochemical properties and intrinsic toxicity; thus, it is imperative but challenging to identify major toxicants. Herein, toxicity identification evaluation (TIE) was applied to identify major toxicants in a typical municipal wastewater treatment plant (WWTP). Impacts of chemical properties on the removal of contaminants and toxicity at individual treatment stages were also examined. The WWTP influent caused 100% death of Daphnia magna and zebrafish embryos, and toxicity characterization suggested that organics, metals, and volatiles all contributed to the toxicity. Toxicity identification based on 189 target and approximately one-thousand suspect chemicals showed that toxicity contributions of organic contaminants, metals, and ammonia to D. magna were 77%, 4%, and 19%, respectively. Galaxolide, pyrene, phenanthrene, benzo[a]anthracene, fluoranthene, octinoxate, silver, and ammonia were identified as potential toxicants. Comparatively, the detected transformation products elicited lower toxicity than their respective parent contaminants. In contrast, the analyzed contaminants showed negligible contributions to the toxicity of zebrafish embryos. Removal efficiencies of these toxicants in WWTP were highly related to their hydrophobicity. Diverse transformation and removal efficiencies of contaminants in WWTPs may influence the chemical compositions in effluent and ultimately the risk to aquatic organisms in the receiving waterways.

Degradation of Benzotriazole UV Stabilizers in PAA/d-Electron Metal Ions Systems-Removal Kinetics, Products and Mechanism Evaluation

Benzotriazole UV stabilizers (BUVs) have gained popularity, due to their absorption properties in the near UV range (200–400 nm). They are used in the technology for manufacturing plastics, protective coatings, and cosmetics, to protect against the destructive influence of UV radiation. These compounds are highly resistant to biological and chemical degradation. As a result of insufficient treatment by sewage treatment plants, they accumulate in the environment and in the tissues of living organisms. BUVs have adverse effects on living organisms. This work presents the use of peracetic acid in combination with d-electron metal ions (Fe²⁺, Co²⁺), for the chemical oxidation of five UV filters from the benzotriazole group: 2-(2-hydroxy-5-methylphenyl)benzotriazole (UV-P), 2-tert-butyl-6-(5-chloro-2H-benzotriazol-2-yl)-4-methylphenol (UV-326), 2,4-di-tert-butyl-6-(5-chloro-2H-benzotriazol-2-yl)phenol (UV-327), 2-(2H-benzotriazol-2-yl)-4,6-di-tert-pentylphenol (UV-328), and 2-(2H-benzotriazol-2-yl)-4-(1,1,3,3-tetramethylbutyl)phenol (UV-329). The oxidation procedure has been optimized based on the design of experiments (DoE) methodology. The oxidation of benzotriazoles follows first order kinetics. The oxidation products of each benzotriazole were investigated, and the oxidation mechanisms of the tested compounds were proposed.

Phase partitioning, transport and sources of Benzotriazole Ultraviolet Stabilizers during a runoff event

Benzotriazole Ultraviolet Stabilizers (BT-UVs) are ubiquitous in the environment, given their wide use as additives in consumer products. Their bio-accumulative and toxic properties are increasingly being scrutinised, evinced by the recent proposition to add UV328 to the Stockholm Convention on Persistent Organic Pollutants. Here, we measured concentrations of six BT-UVs in the dissolved and particulate phases of stream water collected from an urban and rural stream during a runoff event. Under baseflow conditions, the less hydrophobic BT-UVs were present at low concentrations in the dissolved phase, while much higher loads of particulate BT-UVs occurred during stormflow, especially in the urban creek. Time-weighted average BT-UV concentrations were up to 4 times higher in the urban than in the rural creek. BT-UVs were found to be prevalent in water obtained from laundering textiles, which plausibly constitutes a major portion of domestic wastewater, and can serve as a BT-UV source to aquatic waterways. However, the observed dilution of a sewage tracer during the run-off event suggests that unregulated wastewater seepage is not responsible for the high BT-UV loads in storm water. High levels of UV328 and UV234 were detected in a select few plastic debris items collected from the urban watershed and in artificial turf grass, respectively. Whereas this may allow for the leaching of those BT-UVs into the creek, most plastic debris is more likely a sink than a source of BT-UVs. The observed input of particle-bound BT-UVs at the onset of the rain event indicates that most of the BT-UVs reach the creek with contaminated particles that had built up on surfaces during the antecedent dry period. UV328 was the dominant BT-UV in those particles. If such particle build-up occurs on road surfaces, it may suggest that the use of UV328 in automotive applications contributes to their presence in urban storm water.

Determination of UV-327 and its metabolites in human urine using dispersive liquid-liquid microextraction and gas chromatography-tandem mass spectrometry

The benzotriazole UV stabilizer (BUVS) 2-(5-chloro-benzotriazol-2-yl)-4,6-di-(tert-butyl)phenol (UV-327) is added to plastic materials for UV protection. The compound is known to be ubiquitously distributed in the environment. We developed the first analytical method for the determination of UV-327 and seven metabolites, which were identified in vitro, in urine to be able to investigate the in vivo metabolism of UV-327 and to assess potential human exposure to the compound. Enzymatic hydrolysis of phase II conjugates is followed by sample purification with dispersive liquid-liquid microextraction (DLLME). The analytes are extracted from the urine samples after acidification with hydrochloric acid solution and addition of sodium chloride solution. Isopropyl alcohol and chloroform are used as disperser solvent and extraction solvent, respectively. After derivatization, the trimethylsilylated analytes are chromatographically separated and detected by gas chromatography coupled with tandem mass spectrometry (GC-MS/MS). To achieve maximum extraction of the analytes from the sample solution, the DLLME procedure was optimized with respect to the type and volume of disperser and extraction solvent, the pH value of the sample solution, the addition of salt, and the duration of vortex-mixing. Subsequent method validation demonstrated high sensitivity and reliability, with limits of detection (LODs) between 0.05 and 0.1 μg l^-1 and mean relative recovery rates ranging from 88 to 112%. Precision and repeatability were proven by relative standard deviations ranging from 1 to 13% and from 5 to 14%, respectively.

Tissue-Specific Accumulation, Biotransformation, and Physiologically Based Toxicokinetic Modeling of Benzotriazole Ultraviolet Stabilizers in Zebrafish (Danio rerio)

Benzotriazole ultraviolet stabilizers (BUVSs) are high-production-volume chemicals with ubiquitous occurrence in the aquatic environment. However, little is known about their bioconcentration and biotransformation, and physiologically based toxicokinetic (PBTK) models for BUVSs are lacking. This study selected six BUVSs for which experiments were performed with zebrafish (Danio rerio) exposed to two different levels (0.5 and 10 μg·L^-1). Higher kinetic bioconcentration factors (BCFs) were observed at the lower exposure level with environmental relevance, with BCF of 3.33 × 10³ L·kg^-1 for 2-(2-hydroxy-3,5-di-tert-butylphenyl)-5-chlorobenzotriazole (UV-327). This phenomenon was interpreted by a nonlinear adsorption mechanism, where binding with specific protein sites contributes to bioconcentration. Muscle exhibited the lowest accumulation, in which depuration half-life of UV-327 was 19.5 d. In kidney, muscle, ovary, gill, and skin, logBCF increased with increase in log K_OW of the BUVSs until log K_OW was ca. 6.5, above which logBCF decreased. However, the trend was not observed in the liver and intestine. Six biotransformation products were identified and mainly accumulated in the liver and intestine. Considering the nonlinear adsorption mechanism in the PBTK model, the prediction accuracy of the model was improved, highlighting the binding of xenobiotics with specific protein sites in assessing the bioconcentration of chemicals for their risk assessment.

A Comparative Test on the Sensitivity of Freshwater and Marine Microalgae to Benzo-Sulfonamides, -Thiazoles and -Triazoles

The evaluation of the ecotoxicological effects of water pollutants is performed by using different aquatic organisms. The effects of seven compounds belonging to a class of widespread contaminants, the benzo-fused nitrogen heterocycles, on a group of simple organisms employed in reference ISO tests on water quality (unicellular algae and luminescent bacteria) have been assessed to ascertain their suitability in revealing different contamination levels in the water, wastewater, and sediments samples. Representative compounds of benzotriazoles, benzothiazoles, and benzenesulfonamides, were tested at a concentration ranging from 0.01 to 100 mg L−1. In particular, our work was focused on the long-term effects, for which little information is up to now available. Species-specific sensitivity for any whole family of pollutants was not observed. On average, the strongest growth rate inhibition values were expressed by the freshwater Raphidocelis subcapitata and the marine Phaeodactylum tricornutum algae. R. subcapitata was the only organism for which growth was affected by most of the compounds at the lowest concentrations. The tests on the bioluminescent bacterium Vibrio fisheri gave completely different results, further underlining the need for an appropriate selection of the best biosensors to be employed in biotoxicological studies.

Occurrence and transfer of benzophenone-type ultraviolet filters from the pregnant women to fetuses

Benzophenone (BP)-type ultraviolet (UV) filters are widely used in personal care products. Some of them have been identified as endocrine disrupting chemicals. However, little is known about the occurrence of BP-type UV filters in paired maternal-fetal samples. In this study, we investigated the occurrence of eight BP-type UV filters in paired maternal-fetal samples collected from Southern China. Among target analytes, only benzophenone-3 (BP-3) was frequently (detection rate > 80%) detected in maternal-fetal samples, i.e., maternal serum (MS), cord serum (CS), maternal urine (MU) and amniotic fluid (AF). BP-3 was the dominant compound in MS (median: 0.14 ng/mL), CS (0.16) and AF (0.12); whereas MU was dominated by benzophenone-1 (BP-1, 2.85). The median CS/MS ratios (i.e., placental transfer rates) of 4-hydroxy benzophenone (4-OH-BP, 2.35), BP-1 (1.52), benzophenone-4 (BP-4, 1.06), and BP-3 (1.03) were higher than 1.0, suggesting that exposure levels of these chemicals in fetuses were greater than those in mothers. Significant positive correlations (r = 0.667, p < 0.001) of BP-3 concentrations were found between MS and CS, which suggested that MS could be an indicator of fetal exposure to BP-3. Furthermore, the CS/MS ratios of 4-OH-BP, BP-1, BP-3, and benzophenone-8 (BP-8) increased with decreasing molecular weight or log K_ow. Passive diffusion may play an important role in placental transfer of these BP type UV filters. The MU/MS_BP-3 ratio (5.86) was relatively higher than that of MU/MS_BP-1 (0.89), which indicated that BP-3 excretes rapidly in urine. The present study documents the occurrence of eight BP-type UV filters in matched MS, CS, MU and AF samples for the first time in China.

Identification of in vitro phase I metabolites of benzotriazole UV stabilizer UV-327 using HPLC coupled with mass spectrometry

The benzotriazole UV stabilizer (BUVS) 2-(5-chloro-benzotriazol-2-yl)-4,6-di-(tert-butyl)phenol (UV-327) is used in various plastic products to protect them against harmful UV radiation. Meanwhile, there are concerns about potential adverse health effects on humans, as residues of UV-327 and other BUVSs have already been detected in various environmental matrices. However, information on the metabolism of UV-327 is not yet available. Therefore, in vitro experiments with human liver microsomes (HLMs) were performed in order to identify phase I metabolites to be used as specific biomarkers of exposure in biomonitoring studies. The samples were analyzed by HPLC coupled with mass spectrometry (HPLC/MS). Potential metabolites, which were formed by hydroxylation and further oxidation to carboxylic acid, were tentatively identified. Special metabolite structures were suspected and custom-synthesized as reference substances for verification. In total, seven phase I metabolites, which may be suitable biomarkers for the assessment of exposure to UV-327, have been identified and quantified. The results of the present study provide initial insights into the metabolic pathway of UV-327, which is essential for further research on its human metabolism.

Spatial and seasonal variations of organic corrosion inhibitors in the Pearl River, South China: Contributions of sewage discharge and urban rainfall runoff

While organic corrosion inhibitors are ubiquitous in aquatic environments, knowledge on their occurrence, sources and transport in urban surface water is still scarce. In this study, the spatial and seasonal variations of organic corrosion inhibitors and their potential sources were investigated in the Pearl River Delta (PRD), one of the most highly urbanized watersheds in China. A total of 8 compounds belonging to benzothiazole (BTH) and benzotriazole (BTR) groups respectively, were identified in the Pearl River. In addition, there were clear spatial and temporal differentiations in the concentration profiles. The dry season provided higher concentrations of BTH (213-1082 ng L^-1) and BTR (112-1279 ng L^-1) compared to the wet season (30-574 ng L^-1 for BTH and 23-482 ng L^-1for BTR), indicating a dominant process of dilution. Remarkably higher concentrations and similar composition features of targets were observed in the effluent samples from two sewage treatment plants (STPs). Our study indicated that rainfall runoff from urban traffic roads during wet season may also be an important contributor to the Pearl River water environment. The annual total mass loading of corrosion inhibitors from the main channel of the Pearl River is 53.2 tons and exhibited strong seasonal variation. Effluents discharge from STPs and urban rainfall runoff from traffic roads are main sources of corrosion inhibitors to the Pearl River.

Oxidative removal of benzotriazole using peroxymonosulfate/ozone/ultrasound: Synergy, optimization, degradation intermediates and utilizing for real wastewater

This study investigated the degradation efficiency of BTA using combination of ultrasound (US), peroxymonosulfate (PMS), and ozone. The effects of different operational parameters were investigated to optimize the process performance. The results showed that the highest removal efficiency was reached at neutral pH, ozone = 6.8 mg/L, PMS = 1.5 mM and US power = 200 W. Under these conditions, 40 mg/L of BTA was completely degraded within 60 min leading to the almost 85% of chemical oxygen demand removal, 75% of total organic carbon removal and 73.3% of organic nitrogen removal. Based on the scavenging tests, it was found that hydroxyl radical was the main oxidizing agent in the oxidation of BTA by PMS/ozone/US process. The inhibitive effect of anions on BTA removal was under this order NO₂^- > HCO₃^- > Cl^- > NO₃^- > SO₄^2-. Degradation intermediates of BTA were identified and oxidation pathway was proposed. Finally, real samples of saline water, petrochemical wastewater and secondary effluent matrices were investigated for the performance of PMS/ozone/US process and it was found that 54%, 72.3% and 94.6% BTA removal efficiency were reached, respectively. PMS/ozone/US process was compared to US/peroxone (ozone + H₂O₂) and the results showed importance of US irradiation in both systems. Accordingly, PMS/ozone/US process could be considered as an efficient and promising process for BTA degradation in various wastewaters.

Validation of sampling techniques and SPE-UPLC/MS/MS for home and personal care chemicals in the Songhua Catchment, Northeast China

A method for the simultaneous determination of 18 home and personal care chemicals (HPCCs) in river water and wastewater was developed using solid-phase extraction and ultra-high-performance liquid chromatography with tandem mass spectrometry (SPE and UPLC/MS/MS). A series of tests were designed to find the potential background interference and loss of HPCCs during the sample preservation and pretreatment process. Our results suggested that a considerable amount of some target compounds were lost with increasing days of storage even at 4 °C. Accordingly, the samples were stored acidified and refrigerated, including during transportation, to reduce the losses. Experiments on filtration of water samples suggested that recoveries of many HPCCs were significantly affected by the filtration. It is therefore recommended to avoid filtration of water samples where possible. The internal standard corrected recoveries for the HPCCs ranged from 64.2 to 107.0%, except for benzisothiazolone which did not have an appropriate internal standard, in river water which was considered to be the most difficult matrix. The method detection limits for river water, influent and effluent samples were in the ranges of 0.17 to 42 ng/L, 13 to 5100 ng/L, and 0.50 to 200 ng/L, respectively. The validated method was applied for the determination of HPCCs in sewage water collected from a full-scale wastewater treatment plant (WWTP) in a typical urban city in Northeast China and from river water upstream and downstream of the WWTP. Linear alkylbenzene sulphonate, caffeine, methyl paraben, benzalkonium chloride, triclocarban, and triclosan were the major compounds detected in the river water and wastewater samples. Sampling variability for the WWTP (intra-day and inter-day) and cross-river was also determined with the purpose of designing future monitoring requirements. Small variations in these samples confirmed that composite samples and a single sampling event would be representative for future use.

Four typical personal care products in a municipal wastewater treatment plant in China: Occurrence, removal efficiency, mass loading and emission

The occurrence, removal efficiency, mass loading and environmental emission of four categories (benzotriazoles; parabens; antimicrobials; benzophenones) of personal care products were simultaneously determined along the whole process line through an integrated approach (involving both dissolved and adsorbed phase) at a typical wastewater treatment plant in Hunan Province, Southern China. The results showed the prevalence of 13 and 11 target compounds in wastewater and suspended particulate matter, respectively. Twelve substances were detected in the sludge with the mean concentrations ranging from 0.12 to 591.23 ng/g dry weight. Benzotriazoles were the dominant compounds existing in water and antimicrobials were readily being absorbed onto suspended particulate matter and sludge. The overall removal efficiencies of compounds in the total treatment were -84.06%-98.53%. Mass balance results revealed that 85.17%-98.73% of the parabens and benzophenones were removed by degradation, while antimicrobials were removed by being adsorbed onto sludge. However, benzotriazoles could not be efficiently removed and the mass loss was lower than 61.03%. Although ultraviolet radiation played a limited role in removing most target compounds, it still had an impact on removing antimicrobials, 5,6-dimethyl-1H-benzotriazole and 2-hydroxy-4-methoxybenzophenone. The total mass loading and emission of personal care products were 506.35 mg/d/1000 people and 357.56 mg/d/1000 people, respectively. This work would help understand the removal approaches and real pollution of personal care products in the water environment.

Per capita loads of organic UV filters in Australian wastewater influent

Per capita loads of six UV filters were estimated in wastewater influent samples from 36 wastewater treatment plants in Australia collected over a weekend period during the 2016 Australian Census. Of the analysed samples, 99% contained at least one of the target compounds. Phenyl benzimidazole sulfonic acid (PBSA) was the most prevalent (99%), followed by benzophenone 4 (BP4) (97%), benzophenone 3 (BP3) (87%), benzophenone 1 (BP1) (84%), 4-methylbenzylidene camphor (4-MBC) (22%) and isoamyl 4-methoxycinnamate (IMC) (1.5%). The highest concentrations were 3780 and 5070 ng L^-1 for PBSA and BP4, respectively. Total per capita UV filter loads in influent across all plants were calculated using population data from the Australian Census and ranged from 0.21 to 3.4 mg day^-1 person^-1. Notably, a relationship was found between latitude and total per capita daily mass load of UV filters with an increase in mass load from southern to northern catchments. Compared to international studies, mass loads were generally similar with higher loads of BP4 found in Australia. This study provides insight into the occurrence of UV filters in influent wastewater from across Australia and provides the first comprehensive nationwide baseline of UV filter loads.

Biological effects of the benzotriazole ultraviolet stabilizers UV-234 and UV-320 in early-staged zebrafish (Danio rerio)

Among the benzotriazole ultraviolet stabilizers (BUVSs), UV-234 and UV-320 are frequently detected in aquatic ecosystem. Despite the fact that these chemicals are present in low ng/L levels in surface water, they show high bio-accumulation potential and pose exposure risks to aquatic organisms. However, there are limited toxicological data available in fish. In this study, zebrafish embryos were exposed to 0.01, 0.1 and 1 μM UV-234 or UV-320 for up to 6 days. Developmental toxicity as well as effects on mitochondrial bioenergetics, immune system responses, and locomotor activity in zebrafish were measured. After UV-234 treatment (0.1-1 μM), hatching time of embryos was increased compared to controls. There was also a ∼20-40% reduction in non-mitochondrial respiration and oligomycin-dependent mitochondrial respiration in embryos treated with 1 μM UV-234 for 24 and 48 h respectively; conversely basal respiration and non-mitochondrial respiration were increased ∼20-30% in embryos treated with 1 μM UV-320 at 48 h. Transcript levels of sod1 were down-regulated with BUVSs while sod2 mRNA was highly up-regulated with both UV-234 and UV-320, suggesting an oxidative damage response. Considering that mitochondrial signaling regulates innate immune pathways, we measured the expression of immune related transcripts (tlr5a, tlr5b, mmp9, il8, tnfa, cxcl-C1c, nfkb1, and ifng). Of these, only il8 and cxcl-C1c mRNA were decreased in response to 0.1 μM UV-320. To associate early molecular events with behavior, locomotor activity was assessed. UV-234 reduced larval activity in a dark photokinesis assay by ∼15%, however behavioral responses at environmentally-relevant concentrations of BUVSs were not consistent across experiments nor BUVSs. These data suggest that BUVSs can perturb mitochondrial bioenergetics, embryonic development, and locomotor activity of zebrafish, but these responses appear to be dose-, time- and BUVSs dependent, suggesting these chemicals may have unique modes of action.

Occurrence, distribution and ecological risk of ultraviolet absorbents in water and sediment from Lake Chaohu and its inflowing rivers, China

The available information is insufficient to enable a reliable understanding of the global distribution and effect of organic ultraviolet absorbents (UVAs) on ecosystems. Little is known about the pollution of China's lakes by these chemicals. We conducted a survey of UVAs in water and sediment from Lake Chaohu and its inflowing rivers. The UVAs were widely present in this area and the concentrations of total 12 UVAs (Σ₁₂ UVAs) ranged between 162 and 587 ng/L in water and 9.70-178 ng/g in sediment. Benzophenone and benzophenone-3 were dominant in water, and benzophenone and octocrylene dominated in sediment. Higher concentrations of benzophenone were detected in the investigated water samples, although the contamination levels of UVAs in this study were comparable to those investigated in other areas. In addition to the inputs from the UVAs used as filters in cosmetics, the discharge from industries using UVAs as stabilizers also contributed much to the pollution in the study waters. Generally, the risk to aquatic organisms from exposure to UVAs in this area was low, but further research is needed to elucidate the fate of UVAs and to understand bioaccumulation and associated risks.

An evaluation on the intra-day dynamics, seasonal variations and removal of selected pharmaceuticals and personal care products from urban wastewater treatment plants

Pharmaceuticals and personal care products (PPCPs) in wastewater have become an emerging issue due to their negative effects on human health and aquatic ecosystems. Two full-scale municipal and industrial wastewater treatment plants (WWTPs) along the Songhua River were chosen to evaluate the intra-day dynamics, seasonal variations and removal of 12 selected PPCPs. Our results suggested that the selected PPCPs were frequently detected in the influent and effluent. Caffeine was the predominant compound in the influent; while the selected PPCPs was dominated by TCS in the effluent, suggesting the different fates of selected PPCPs in the WWTPs. The intra-day dynamics of PPCPs in the influent were evaluated, suggesting that the 12 PPCPs can be grouped into three categories because of their different use patterns. The analysis of seasonal changes of PPCPs concentrations in the WWTPs suggested that the concentrations of some PPCPs were influenced by the chemical usage, degradation and temperature. The removal efficiency for the PPCPs were very high with the values ranged from 70.0% to 99.7% for WWTP#1, and from 62.5% to 99.4% for WWTP#2. Significant seasonal variations of PPCPs removal efficiency were observed. Base on the mass loading of PPCPs in the two WWTPs, our results suggested that WWTP#1 in the urban core received much more PPCPs in comparison to WWTP#2 in the suburban regions, suggesting that influences of the service population.

Occurrence and fate of substituted diphenylamine antioxidants and benzotriazole UV stabilizers in various Canadian wastewater treatment processes

Substituted diphenylamine antioxidants (SDPAs) and benzotriazole UV stabilizers (BZT-UVs) are additives used in industrial and consumer products to prevent degradation or color change of materials, but their environmental fate and disposition are not well characterized. In this study, SDPAs and BZT-UVs were analyzed in 68 liquid and 39 solid samples collected from 9 wastewater treatment plants (WWTPs) in Canada to investigate the occurrence and fate of these contaminants. The median concentrations of ΣSDPAs and ΣBZT-UVs was 483 and 76.2 ng L^-1 in influent, 28.4 and 4.84 ng L^-1 in effluent, and 2750 and 457 ng g^-1 in biosolids (dry weight), respectively. Dinonyl-diphenylamine (C9C9) was the predominant congener of SDPAs in all matrices (>40%). For target BZT-UVs, the major components were 2-(2H-benzotriazol-2-yl)-4,6-bis(1-methyl-1-phenylethyl)phenol (UV234) and 2-(2H-benzotriazol-2-yl)-4,6-di-tert-pentylphenol (UV328). SDPAs and BZT-UVs were effectively removed (>90%) from the liquid stream in most WWTPs mainly through sludge sorption and separation, but biotransformation, UV treatment and filtration may also contribute to removal of some contaminants in advanced treatment plants. In contrast, the removal efficiency of target contaminants using chemically assisted primary treatment was low, likely due to the short hydraulic retention time of this site. Our results suggest that wastewater effluent is a vector of SDPAs and BZT-UVs to the aquatic environment. The results also highlight the high concentrations of SDPAs and BZT-UVs associated with the solid stream in WWTPs, which could affect the beneficial use of biosolids (e.g., compost or land applications).