Performance evaluation of polymer-marine biomass based bionanocomposite for the adsorptive removal of malachite green from synthetic wastewater

Microwave catalytic treatment using magnetically separable CoFe2O4 spinel catalyst for high-rate degradation of malachite green dye

The release of toxic chemical dyes from the industrial effluent poses huge challenges for the environmental engineers to treat it. Azo dyes encompass the huge part of textile discharges which are difficult to degrade due to their complex chemical aromatic structures and due to the presence of strong bonds (-N=N-). Thus, the removal of a carcinogenic azo dye (i.e., malachite green (MG)), via microwave (MW) - assisted technology in the presence of spinel cobalt ferrite (CoFe2O4) catalyst was investigated. The synthesized CoFe2O4 nanoparticles were characterized via XRD, FTIR, TGA, VSM, and SEM-EDAX analytical techniques. The nanoparticles were found to be spherical (17.42 nm), and crystalline in nature. The impact of MW power (300-700W), MW temperature (60°- 90 °C), CoFe2O4 dosage (0-1.2 g/L), and initial MG dye concentrations (15-100 mg/L) on MG removal were studied. The maximum MG decolorization (>90%) was observed within 2 min, and the remaining decolorization was completed within next 3 min under the optimized condition. The reaction rates were significantly boosted by MW irradiation, resulting in faster MG degradation with pseudo second-order kinetics rate (R2 ∼ 0.99). The MW irradiation would induce the localised hotspot zones over the catalytic surface, thus promoting the reactive radical species generation, which targeted the organic pollutant achieving the higher degree of mineralization (TOC∼90%). The toxicity reduction after the MW treatment suggests that the bulky toxic aromatic chains of the dye compound might have fragmented into simpler, smaller, and less toxic compounds. The ⦁OH played a major role in the degradation of MG dye through demethylation, elimination of benzene rings, and subsequent mineralization to CO2, and H2O. No detectable leaching of cobalt (Co) metal was observed from the catalyst, which ensured the stability of Co in the catalyst. Moreover, CoFe2O4 was recovered easily after the MW treatment via external magnetic separation, due to its high saturation magnetization value (i.e., 59.5 emu/g). Additionally, cost incurred for dye removal via MW irradiation was compared ($ 308 per kg of the dye pollutant removed) with several other processes, and found on economic side in comparison. According to the findings, the microwave irradiation process assisted by CoFe2O4 treatment offers a practical, and potential approach for treating dye laden wastewater, along with the easier catalyst retrieval mechanism using magnetism.

Hydrothermal fabrication of composite chitosan grafted salicylaldehyde/coal fly ash/algae for malachite green dye removal: A statistical optimization

In this study, chitosan grafted salicylaldehyde/coal fly ash/algae (Chi-SL/CFA/Alg) was synthesized by assistance of hydrothermal process to be an effective adsorbent to remove cationic dye (malachite green: MG) from water. The physicochemical properties of the Chi-SL/CFA/Alg biomaterial were examined using SEM-EDX, pHpzc, specific surface area (BET), and FTIR analyses. The optimization process of the adsorption operation parameters for MG removal by Chi-SL/CFA/Alg were optimized using a Box-Behnken design (BBD). The selected adsorption operation parameters Chi-SL/CFA/Alg dosage (A: 0.02-0.1 g/100 mL), solution pH (B: 4-8), and contact time (C: 20-360 min). Analysis of variance (ANOVA) test was applied to determine the significant interaction between the adsorption operation parameters and to validate BBD output. The adsorption kinetics and isotherms of MG dye by Chi-SL/CFA/Alg were well described by pseudo-second order (PSO) kinetic and Freundlich isotherm model respectively. Thus, the maximum adsorption capacity (qmax) of MG dye by Chi-SL/CFA/Alg was found to be 493.7 mg/g at basic pH environment (pH = 8) and working temperature 25 °C. The adsorption mechanism can be ascribed to various interactions, including hydrogen bonding, π-π interactions, electrostatic attraction, and n-π interactions. Thus, Chi-SL/CFA/Alg can be considered as preferable and potential adsorbent for removing cationic dye from aqueous environment.

Artificial neural network-based modeling of Malachite green adsorption onto baru fruit endocarp: insights into equilibrium, kinetic, and thermodynamic behavior

In this study, artificial neural network (ANN) tools were employed to forecast the adsorption capacity of Malachite green (MG) by baru fruit endocarp waste (B@FE) under diverse conditions, including pH, adsorbent dosage, initial dye concentration, contact time, and temperature. Enhanced adsorption efficiency was notably observed under alkaline pH conditions (pH 10). Kinetic analysis indicated that the adsorption process closely followed a pseudo-second-order model, while equilibrium studies revealed the Langmuir isotherm as the most suitable model, estimating a maximum adsorption capacity of 57.85 mg g-1. Furthermore, the chemical adsorption of MG by B@FE was confirmed using the Dubinin-Radushkevich isotherm. Thermodynamic analysis suggested that the adsorption is spontaneous and endothermic. Various ANN architectures were explored, employing different activation functions such as identity, logistic, tanh, and exponential. Based on evaluation metrics like the coefficient of determination (R2) and root mean square error (RMSE), the optimal network configuration was identified as a 5-11-1 architecture, consisting of five input neurons, eleven hidden neurons, and one output neuron. Notably, the logistic activation function was applied in both the hidden and output layers for this configuration. This study highlights the efficacy of B@FE as an efficient adsorbent for MG removal from aqueous solutions and demonstrates the potential of ANN models in predicting adsorption behavior across varying environmental conditions, emphasizing their utility in this field.

Prediction of adsorption performance of ZIF-67 for malachite green based on artificial neural network using L-BFGS algorithm

Given the necessity and urgency in removing organic pollutants such as malachite green (MG) from the environment, it is vital to screen high-capacity adsorbents using artificial neural network (ANN) methods quickly and accurately. In this study, a series of ZIF-67 were synthesized, which adsorption properties for organic pollutants, especially MG, were systematically evaluated and determined as 241.720 mg g-1 (25 ℃, 2 h). The adsorption process was more consistent with pseudo-second-order kinetics and Langmuir adsorption isotherm, which correlation coefficients were 0.995 and 0.997, respectively. The chemisorption mechanism was considered to be π-π stacking interaction between imidazole and aromatic ring. Then, a Python-based neural network model using the Limited-memory BFGS algorithm was constructed by collecting the crucial structural parameters of ZIF-67 and the experimental data of batch adsorption. The model, optimized extensively, outperformed similar Matlab-based ANN with a coefficient of determination of 0.9882 and mean square error of 0.0009 in predicting ZIF-67 adsorption of MG. Furthermore, the model demonstrated a good generalization ability in the predictive training of other organic pollutants. In brief, ANN was successfully separated from the Matlab platform, providing a robust framework for high-precision prediction of organic pollutants and guiding the synthesis of adsorbents.

Plant-mediated synthesis of Mn3O4nanoparticles: challenges and applications

This review focuses on the green synthesis methods, challenges, and applications of manganese oxide (Mn3O4) nanoparticles investigated in the past five years. Mn3O4nanoparticles offer some unique properties that are attributed in part to the presence of mixed oxidation states of manganese (i.e. +2 and +3) in the particle, which can be utilized in a wide range of redox-sensitive applications, such as in developing supercapacitive energy storage materials. In addition, the green synthesis of Mn3O4nanoparticles through plant extracts has potential uses in sustainable nanotechnology. Various plant extract-mediated synthesis techniques for Mn3O4nanoparticles have been investigated and presented. By comparing the size and structure of the synthesized Mn3O4nanoparticles, we have observed a consistent pattern of obtaining spherical particles with a size ranging from 16 to 50 nm. The morphology of the generated Mn3O4nanoparticles can be influenced by the annealing temperature and the composition of the plant extract used during the nanoparticle synthesis. Additionally, numerous applications for the greenly produced Mn3O4nanoparticles have been demonstrated. Mn3O4nanoparticles derived from plant extracts have been found to possess antimicrobial properties, supercapacitive and electrochemical capabilities, and excellent pollutant degradation efficiency. However, the magnetic properties of these nanoparticles synthesized by plant extracts are yet to be explored for potential biomedical applications. Finally, challenges to existing synthetic methods and future perspectives on the potential applications of these green synthesized Mn3O4nanoparticles are highlighted.

Plant-mediated synthesis of silver-doped ZnO nanoparticles with high sonocatalytic activity: Sonocatalytic behavior, kinetic and thermodynamic study

Together with the rapid growth of technology, the discharge of wastewater from industry into environment had become a hot topic among society nowadays. More attention had been given to the development of water treatment techniques. In this study, sonocatalysis was proposed to degrade the organic pollutants using silver-doped zinc oxide (Ag-ZnO) nanoparticles which were synthesized via green synthesis process using Clitoria ternatea Linn (Asian Pigeonwings flower). The characterization results revealed that the incorporation of Ag into the ZnO lattice decreased the crystallite size and increased the specific surface area of ZnO nanoparticles. It is noteworthy that about 98% of sonocatalytic degradation efficiency of malachite green (MG) was successfully achieved within 30 min in the presence of 5 wt.% Ag-ZnO with 1.0 g/L of catalyst loading under 500 mg/L of initial dye concentration, 80 W of ultrasonic power, 45 kHz of ultrasound frequency, and 2.0 mM of oxidant concentration. The kinetic study showed that the sonocatalytic degradation of organic dye was fitted well into second-order kinetic model with high R2 value (0.9531). In the thermodynamic study, negative value of standard Gibbs free energy and low value of activation energy (+ 24.43 kJ/mol) were obtained in the sonocatalytic degradation of MG using the green-synthesized Ag-ZnO sample. HIGHLIGHTS: • Facile synthesis of silver-doped zinc oxide nanoparticles using plant extract which act as reducing and stabilizing agents • Optical, physical, and chemical characterization of green-synthesized nanomaterials were performed • Evaluation of sonocatalytic degradation of organic dye using green-synthesized nanomaterials • Sonocatalytic behavior, kinetic and thermodynamic studies of sonocatalytic reaction.

A response surface model to examine the reactive red 239 sorption behaviors on Rhizoclonium hieroglyphicum: isotherms, kinetics, thermodynamics and toxicity analyses

The present study is an attempt to investigate the potentiality of Rhizoclonium hieroglyphicum in the removal of reactive red 239 (RR239) from aqueous solution and to assess the toxicity of the treated dye solution. Optimisation of the process variables namely dye and biosorbent concentrations, pH, temperature and incubation time for RR239 removal was performed using Response Surface Methodology (RSM) assisted Box Behnken Design (BBD) model. The recycling and regeneration efficiency of the dye adsorbed alga was evaluated using different eluents under optimized conditions. Further to understand the adsorption mechanism, isotherms, kinetics and thermodynamic studies were performed. UV-vis and FT-IR spectroscopy was employed to confirm the interaction between the adsorbate and biosorbent. The nature of the treated dye solution was assessed using phyto, microbial and brine shrimp toxicity studies. On the basis of quadratic polynomial equation and response surfaces given by RSM, 90% decolorization of RR239 was recorded at room temperature under specified optimal conditions (300 mg/L of dye, 500 mg/L of biosorbent, pH 8 and 72 h of contact time). Desorption experiments demonstrated 88% of RR239 recovery using 0.1 N acetic acid as an eluent and 81% of dye removal in regeneration studies. The data closely aligned with Freundlich isotherm (R2 - 0.98) and pseudo-second-order kinetic model (R2 - 0.9671). Thermodynamic analysis revealed that the process of adsorption was endothermic, spontaneous, and favorable. UV-Vis and FT-IR analyses provided evidence for adsorbate-biosorbent interaction, substantiating the process of decolorization. In addition, the results of phyto, microbial and brine shrimp toxicity assays consistently confirmed the non-toxic nature of the treated dye. Thus, the study demonstrated that R. hieroglyphicum can act as a potent bioremediation agent in alleviating the environmental repercussions of textile dyeing processes.

Removal of an agricultural herbicide (2,4-Dichlorophenoxyacetic acid) using magnetic nanocomposite: A combined experimental and modeling studies

This study focused on modeling the removal of one of the widely used agricultural herbicides known as 2,4-Dichlorophenoxyacetic acid (2,4-D) using polypyrrole-coated Fe2O3 nanoparticles (Fe2O3@PPy). The Fe2O3@PPy nanocomposite was synthesized by surface-coating the Tabebuia aurea leaf extract synthesized Fe2O3 nanoparticles with polypyrrole. After characterization, the adsorptive potential of the nanocomposite for removing 2,4-D from aqueous solution was examined. Central composite design (CCD) was employed for optimizing the adsorption, revealing an adsorption efficiency of 90.65% at a 2,4-D concentration of 12 ppm, a dosage of 3.8 g/L, an agitation speed of 150 rpm, and 196 min. Adsorption dataset fitted satisfactorily to Langmuir isotherm (R2: 0.984 & χ2: 0.054) and pseudo-second-order kinetics (R2: 0.929 & χ2: 0.013) whereas the exothermic and spontaneous nature were confirmed via the thermodynamic study. The predictive models, including adaptive neuro-fuzzy inference system (ANFIS), artificial neural network (ANN), and response surface methodology (RSM), demonstrated good precision for the prediction of 2,4-D adsorption, with respective R2 of 0.9719, 0.9604, and 0.9528. Nevertheless, statistical analysis supported ANFIS as the better forecasting tool, while RSM was the least effective. The maximum adsorption capacity of 2,4-D onto the Fe2O3@PPy nanocomposite was 7.29 mg/g, significantly higher than a few reported values. Therefore, the Fe2O3@PPy nanocomposite could serve as a competent adsorbent to remove 2,4-D herbicide from aqueous streams.

Sustainable remediation of toxic congo red dye pollution using bio based carbon nanocomposite: Modelling and performance evaluation

Remediation of synthetic dyes found in aqueous environment poses a serious challenge for treatment due to their resistance to chemical and biological degradation. This research study investigated the application of Chitosan-ZnO-Seaweed bio nanocomposite in the remediation of congo red. The novel bionanocomposite was characterised by FTIR, SEM, TEM, EDS and XRD studies. The FTIR spectra and SEM images indicated the adsorption of congo red onto the synthesized bionanocomposite. The batch wise experimental studies were done to explore the influence of process variables on removal of congo red from synthetic wastewater and to determine optimized conditions. Under optimized conditions of pH 3, temperature 40 °C, initial congo red concentration 50 mg/L, bionanocomposite quantity 0.03 g/L and interaction period 30 min, the bionanocomposite removed 95.64% of congo red. Thermodynamic studies were carried out and the parameters, ΔH° and ΔS° were found to be 38.386 kJ/mol and 0.1451 kJ/mol. K, respectively. The isotherm and kinetic study showed that monolayer Langmuir model was obeyed (R2 = 0.968) and the experimental value of congo red adsorption correlated well with pseudo second order model (R2 = 0.9938) respectively. The maximum adsorption capacity was found to be 303.03 mg/g. Protonated amino group of chitosan, hydroxyl group of seaweed accounts for congo red adsorption along with zinc oxide.

Toxic Effects of Methylene Blue on the Growth, Reproduction and Physiology of Daphnia magna

Methylene blue (MB) is a disinfectant used in aquaculture to prevent and treat fish diseases. However, the release of MB can pose a risk to the receiving water bodies. Zooplankton are the most sensitive organisms among aquatic life. Hence, this study examined the acute and chronic toxic effects of MB on zooplankton using Daphnia magna (D. magna) as a test organism to provide basic data for risk assessment. The results show that 48 h-EC₅₀ and 24 h-LC₅₀ were 61.5 ± 2.3 and 149.0 ± 2.2 μg/L, respectively. Chronic exposure to MB affected the heart rate, beat frequency of the thoracic limbs, and reproductive ability of D. magna at environmental concentrations higher than 4.7 μg/L. The cumulative molts, time to production of the first brood, and total number of living offspring were affected at different MB concentrations, while "abortions" were observed in high-exposure groups. The activity of superoxide dismutase was increased, while glutathione S-transferase activity was stimulated at low concentrations and inhibited at high concentrations. In addition, the malondialdehyde content increased with increasing concentrations of MB. Our findings demonstrate the impact of MB on the reproduction and growth of freshwater species, as well as their physiological responses. These results have implications for establishing guidelines on the use of MB in aquaculture and setting discharge standards.

Bandgap engineering approach for designing CuO/Mn3O4/CeO2 heterojunction as a novel photocatalyst for AOP-assisted degradation of Malachite green dye

A ternary nanohybrid CuO/Mn₃O₄/CeO₂ was developed in the present work using a co-precipitation-assisted hydrothermal method. The designed photocatalyst's structural, morphology, elemental composition, electronic states of elements, and optical properties were studied using corresponding analytical techniques. Results from PXRD, TEM/HRTEM, XPS, EDAX, and PL showed that the desired nanostructure had formed. Using Tauc's energy band gap plot, it was determined that the nanostructures band gap was ~ 2.44 eV, which showed the band margins of the various moieties, CeO₂, Mn₃O₄, and CuO, had modified. Thus, improved redox conditions led to a substantial decrease in the recombination rate of electron-hole pairs, which was further explained by a PL study in that charge separation plays a key role. Under exposure to visible light irradiation for 60 min, it was revealed that the photocatalyst achieved 98.98% of photodegradation efficiency for malachite green (MG) dye. The process of photodegradation proceeded according to a pseudo-first-order reaction kinetic model with an excellent rate of reaction of 0.07295 min^-1 with R² = 0.99144. The impacts of different reaction variables, inorganic salts, and water matrices were investigated. This research seeks to create a ternary nanohybrid photocatalyst with high photostability, visible spectrum activity, and reusability up to four cycles.

Performance Evaluation of Gum Gellan-Based Hydrogel as a Novel Adsorbent for the Removal of Cationic Dyes: Linear Regression Models

In this work, the suitability and efficacy of the previously reported biodegradable gellan gum (GG)-based hydrogel have been thoroughly investigated with respect to the adsorption mechanisms of malachite green (MG) and methylene blue (MB) dyes. The dyes' removal from aqueous solutions using GG-cl-poly(AA) as an adsorbent material has been studied in a discontinuous system with respect to contact time, dose, pH, and temperature. The synthesized hydrogel was characterized by FT-IR, TGA, XRD, ¹H NMR, and FE-SEM. The adsorption capacity of GG-cl-poly(AA) hydrogel was investigated at different pH solutions (3, 7, and 10), and it was found that neutralized charge plays a crucial role in the enhancement of dye removal. To better understand the behavior of the GG-cl-poly(AA) hydrogel in adsorbing model dyes, adsorption kinetics, isotherms, and thermodynamics were also investigated. The values of qmax for MG and MB were obtained to be 552.48 and 531.9 mg g^-1. In addition, the influence of NaCl concentration on adsorption efficiency was investigated, and it was found that as the ion concentration increased, the effectiveness of the adsorption process dropped. Moreover, the synthesized hydrogel's potential application in the adsorption and separation of dyes from wastewater is enhanced by the reusability investigations conducted in convenient conditions. As a result, it is possible to conclude that reusing GG-cl-poly(AA) hydrogel as a low-cost, easy-to-handle, nontoxic material in an industrial wastewater treatment plant's adsorption process can provide a number of advantages, including high efficiency for MG and MB removal and cost savings on overall treatment plant operations.

Porous nanocomposites for sorptive elimination of ibuprofen from synthetic wastewater and its molecular docking studies

Pharmaceuticals are a new developing pollutant that is threatening aquatic ecosystems and impacting numerous species in the ecosystem. The aim of this study is the green synthesis of TiO₂-Fe₂O₃-Chitosan nanocomposites in conjunction with Moringa olifera leaves extract and its applicability for ibuprofen removal. Various characterization studies were performed for the synthesized nanocomposites. Box-Behnken design (BBD) is employed to optimize pH, agitation speed, and composite dosage. Equilibrium results show that adsorption process matches with Langmuir isotherm, demonstrating adsorption on the nanocomposite's homogenous surface and follows pseudo-first-order kinetics. Using the BBD, pH, adsorbent dose, and agitation speed were examined as adsorption parameters. Ibuprofen elimination was demonstrated to be most successful at a pH of 7.3, using 0.05 g of nanocomposites at a rotational speed of 200 rpm. Thermodynamic parameters for ibuprofen sorption were carried out and the ΔH and ΔS was found to be 76.23 & 0.233. Molecular Docking was performed to find the interaction between the pollutant and the nanocomposite. UV-vis spectra confirm the 243 nm absorption band corresponding to the nanocomposite's surface plasmon resonances. Fourier transform infrared spectroscopy spectra relate this band to a group of nanocomposites. The findings of this work emphasize the importance of TiO₂-Fe₂O₃-Chitosan nanocomposites for removing ibuprofen from wastewater.

Facile synthesis of biogenic palladium nanoparticles using biomass strategy and application as photocatalyst degradation for textile dye pollutants and their in-vitro antimicrobial activity

Among biological applications, plant-mediated Pd NPs for multi-drug resistance (MDR) developed in pathogenic bacteria were synthesized with the help of biomass of lemon peel, a biological material, with a non-toxic, environmentally friendly, human-nature green synthesis method. Characterization of synthesized Pd NPs was carried out by UV-Vis spectrometry, Transmissive Electron Microscopy (TEM), X-ray diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FTIR) techniques. According to TEM analysis, Pd NPs were confirmed to be in a spherical shape and the mean particle size was determined to be 4.11 nm. The crystal structure of Pd NPs was checked using XRD analysis and the mean particle size was observed to be 6.72 nm. Besides, the antibacterial activity of Pd NPs was determined against Escherichia coli (E. coli) (ATCC 8739), Bacillus subtilis (B. subtilis ATCC 6633), Staphylococcus aureus (S. aureus ATCC 6538), Klebsiella pneumoniae (K. pneumoniae ATCC 11296) and Serratia marcescens (S. marcescens ATCC) bacteria. Antibacterial activity was determined to be high in Pd NPs which is in conformance with the results acquired. The Pd NPs showed good photocatalytic activity, after 90 min illumination, about 81.55% and 68.45% of MB and MO respectively were catalysed by the Pd NPs catalyst, and 74.50% of RhB dyes were removed at 120 min of illumination. Within the scope of this project, it is recommended to use Pd NPs obtained by the green synthesis in the future as an antibacterial agent in biomedical use and for the cleaning of polluted waters.

Heterostructured γ-Fe2O3/FeTiO3 magnetic nanocomposite: An efficient visible-light-driven photocatalyst for the degradation of organic dye

The catalyst recovery is the major concern in commercialization of photocatalysts for the industrial effluent treatment process. To overcome this major issue, Fe₂O₃ based magnetic photocatalytic heterostructure ɣ-Fe₂O₃/FeTiO₃ nanocomposite was synthesized by hydrothermal method. Fe₂O₃ is the cheapest visible active magnetic photocatalytic material, but it has the limitation of fast e^-/h + recombination. Titanium (Ti) was loaded on γ-Fe₂O₃ to overcome this issue. The loaded Ti has grown as FeTiO₃ on the surface of ɣ-Fe₂O₃ nanocrystals and emerged as heterostructure ɣ- Fe₂O₃/FeTiO₃ nanocomposites, which was confirmed by XRD and TEM results. The loading concentration of Ti on γ-Fe₂O₃ was optimized to achieve the maximum photocatalytic efficiency without compromising the magnetic property of γ-Fe₂O₃ to facilitate the magnetic separation. DRS-UV spectra revealed the strong visible light response of γ- Fe₂O₃/FeTiO₃ nanocomposite. The photocatalytic efficiencies of the synthesized materials were evaluated using methylene blue (MB) as a model pollutant under sunlight. The built-in electric field between p-n junction between FeTiO₃ and Fe₂O₃ and type II charge transfer mechanism extended the lifetime of the charge carriers at the heterojunction of γ- Fe₂O₃/FeTiO₃, which was confirmed by PL spectra. The vibrating sample magnetometer (VSM) study revealed the decreasing magnetization, coercivity (Hc), and retentivity (Mr) of γ-Fe₂O₃ with increasing concentration of Ti. 92% of the used-up 20 wt% Ti loaded γ-Fe₂O₃/FeTiO₃ magnetic nanocomposite was recovered from the treated wastewater using an electromagnet. Both magnetic properties and efficiency of the nanocomposite increased up to 20 wt% of Ti loading, beyond that decreased due to the increasing composition of antiferromagnetic FeTiO₃ and the increasing number of defect sites as recombination centers. Hence, 20 wt% loading of Ti was concluded as the optimum to enhance the efficiency and to retain the magnetic properties. This work aims the commercialization of magnetic photocatalytic materials for the industrial effluent treatment.

Green synthesis of Mn3O4 nanoparticles using Costus woodsonii flowers extract for effective removal of malachite green dye

The pollution of organic dyes such as malachite green is one of the globally critical issues, calling for efficient mitigation methods. Herein, we developed green Mn₃O₄ nanoparticles synthesized using natural compounds extracted from Costus woodsonii flowers under an ultrasound-assisted mode. The materials were characterized using several physicochemical techniques such as Fourier-transform infrared spectroscopy, X-ray diffraction, Energy-dispersive X-ray spectroscopy, scanning electron microscopy, Raman spectroscopy, and N₂ adsorption desorption isotherm measurement. The X-ray diffraction and N₂ isotherm plots confirmed the presence of tetragonal γ-Mn₃O₄ phase and mesoporous structure, respectively. Carbonyl groups derived from flavonoids or carboxylic compounds were found in the surface of green Mn₃O₄ nanoparticles. The effect of pH, contact time, dose, and concentration on the adsorption of malachite green over green Mn₃O₄ was carried out. The maximum malachite green adsorption capacity for green Mn₃O₄ nanoparticles was 101-162 mg g^-1. Moreover, kinetic and isotherm adsorption of malachite green obeyed Langmuir (R_adj.² = 0.980-0.995) and pseudo first-order models (R_adj.² = 0.996-1.00), respectively. Adsorption of malachite green over green Mn₃O₄ was a thermodynamically spontaneous process due to negative Gibbs free energy values (ΔG^ο < 0). Green Mn₃O₄ nanoparticles offered a high stability through the FR-IR spectra analysis. With a good recyclability of 4 cycles, green Mn₃O₄ nanoparticles can be used as potential adsorbent for removing malachite green dye from water.

A techno-economic approach for eliminating dye pollutants from industrial effluent employing microalgae through microbial fuel cells: Barriers and perspectives

Microbial fuel cells are biochemical factories which besides recycling wastewater are electricity generators, if their low power density can be scaled up. This also adds up to work on many factors responsible to increase the cost of running a microbial fuel cell. As a result, the first step is to use environment friendly dead organic algae biomass or even living algae cells in a microbial fuel cell, also referred to as microalgal microbial fuel cells. This can be a techno-economic aspect not only for treating textile wastewater but also an economical way of obtaining value added products and bioelectricity from microalgae. Besides treating wastewater, microalgae in its either form plays an essential role in treating dyes present in wastewater which essentially include azo dyes rich in synthetic ions and heavy metals. Microalgae require these metals as part of their metabolism and hence consume them throughout the integration process in a microbial fuel cell. In this review a detail plan is laid to discuss the treatment of industrial effluents (rich in toxic dyes) employing microbial fuel cells. Efforts have been made by researchers to treat dyes using microbial fuel cell alone or in combination with catalysts, nanomaterials and microalgae have also been included. This review therefore discusses impact of microbial fuel cells in treating wastewater rich in textile dyes its limitations and future aspects.

Adsorption of rutin from olive mill wastewater using copolymeric hydrogels based on N-vinylimidazole: Kinetic, equilibrium, and thermodynamics assessments

Olive mill wastewater, also known as olive wastewater, contains biologically active components with various beneficial effects on health. The development of novel adsorbent materials for the recovery of these biologically active substances is important area of research. In this study, copolymeric hydrogels based on N-vinylimidazole (VIm), a new material that has never been used as an adsorbent in the separation of phenolic components, were synthesized. The hydrogels synthesized in this study is copolymer structures based on N-vinylimidazole (VIm) containing [2- (methacryloxy) ethyl] dimethylpentylammonium bromide (QDMAC5) in different moles. QDMAC5 was obtained by quaternization of 2- (dimethylamino) ethyl methacrylate (DMA) with 1-bromopentane (C5). The production of copolymer hydrogels was carried out by free radical solution polymerization. The syntheses were carried out only by changing the monomer composition so that the crosslinker ratio remained constant (1.2 mol%). The QDMAC5 content in the copolymers was 5, 10, 20, 30, and 50 mol%. So, the resulting structures were named PVQ-5%, PVQ-10%, PVQ-20%, PVQ-30%, and PVQ-50%, respectively. Functional group characterizations of hydrogels were made by Fourier Transform Infrared Spectrometry (FTIR). The surface of the hydrogels was analyzed by Scanning Electron Microscopy (SEM). Finally, thermogravimetric analyzes (TGA) were performed to investigate the thermal degradation behavior. The recovery of the rutin present in olive mill wastewater has been investigated as a model study. Kinetic data has been represented by the selected models (pseudo-first order, pseudo-second order, and intraparticle diffusion) convincingly (R² > 0.76), while the equilibrium findings have fitted well to Langmuir, Freundlich, and Temkin equations (R² > 0.77). Rutin adsorption process on N-vinylimidazole (VIm) based copolymeric hydrogels has been found as exothermic and spontaneous chemisorption process depending on the thermodynamic analysis.

Potential applications of spent adsorbents and catalysts: Re-valorization of waste

Water pollution has increased with the growth of human population and its industrial activities. Textile effluents constitute a particular threat due to the presence of heavy metals and dyes. Adsorption is one of the most applied technologies in contaminant removal owing to its high efficiency, low cost, practical implementation and possibility to operate in several experimental conditions. However, this process implies the generation of spent materials, representing a limitation to scale-up. Although the applications of exhausted solids in effluent treatments have not been extensively reviewed before, their reutilization appears to be an environmentally and economically attainable alternative. This work summarizes the potential value of solids post-use. The open literature reports that spent adsorbents based on polysaccharides with iron oxides may adsorb up to 1 g g^-1 of organic pollutants and up to near 100% of metallic ions from wastewater (Cu²⁺, Cd²⁺, Zn²⁺, Pb²⁺). The studied conditions vary from 30 to 60 °C, 0,05 to 6 g L^-1 of adsorbent, 10 mg L^-1 to 250 mg L^-1 of organic pollutants (dyes) and pH between 2 and 8. Spent adsorbents in dye removal have proven to have near 95% efficiency in metallic ion adsorption. Otherwise, the spent solids could be applied to remove Ca²⁺ and Mg²⁺ to decrease the hardness of water. Furthermore, at the end-of-life, these materials could be used in cement and ceramic production. To achieve these aims, it is necessary to design the bioadsorbents and biocatalysts considering not only their primary uses (as adsorbent of organic pollutants), but also secondary applications (as toxic metal or hardness removal) and even their final destination (as additive in ceramic or cement production). Finally, further studies are required on the composition, properties, stability at long-term and the life-cycle cost of these materials when they are applied in the construction industry.

A comprehensive review on sources, analysis and toxicity of environmental pollutants and its removal methods from water environment

Natural and human anthropogenic activities increase the concentration of the toxic pollutant in the water environment; they could cause harmful effects even in their lower concentration. In humans, toxic pollutants damage the structural and functional properties of essential organs including the heart, liver, kidneys, reproductive systems and pancreas. To avoid the toxicity of the pollutant, they should be removed from the water environment. Since various conventional water/wastewater treatment technologies including precipitation, ion exchange, flocculation, filtration, electrodialysis and membrane separation are employed to reduce the concentration of the pollutant, they have various difficulties in implementation, efficiency and ecological perspective. Therefore, several researchers are now focusing on alternative and eco-friendly approach called biosorption to remove toxic contaminants from the water environment. The biosorption innovation is one of the acclaimed systems for water treatment. The noteworthy endeavours have been made throughout the years to grow profoundly particular and effective biosorbent materials that are more effective, abundantly available, and cost-effective. Biosorption is effectively executed by utilizing both living and dead biomasses of bacteria, fungi and algae. Moreover, agro-waste materials are also utilized as biosorbents due to their excellent surface properties, abundant availability and cost-effectiveness. A variety of physical and chemical treatments enhances the biosorption capabilities of biosorbents via modifying their surface properties. In this review, biosorption mechanism, influencing parameters and application of biosorbent materials towards the removal of toxic pollutants are discussed. The future research opportunities for sustainable wastewater treatment were also explained.

Preparation and Characterization of a Novel Activated Carbon@Polyindole Composite for the Effective Removal of Ionic Dye from Water

The present study is aimed at the synthesis and exploring the efficiency of a novel activated carbon incorporated polyindole (AC@PIN) composite for adsorptive removal of Malachite Green (MG) dye from aqueous solution. An AC@PIN hybrid material was prepared by in situ chemical oxidative polymerization. The physico-chemical characteristics of the AC@PIN composite were assessed using Fourier-transform infrared spectrometer, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, ultraviolet visible spectroscopy, and determination of point of zero charge (pH_PZC). A series of adsorption studies was conducted to evaluate the influence of operational parameters such as pH, contact time, initial dye concentration, AC@PIN dosage, and temperature on dye adsorption behavior of developed composite. A maximum dye removal percentage (97.3%) was achieved at the pH = 10, AC@PIN dosage = 6.0 mg, initial dye concentration 150 mg L⁻¹, and temperature = 20 °C. The kinetic studies demonstrated that the adsorption of MG on AC@PIN followed pseudo-second-order model (R² ≥ 0.99). Meanwhile, Langmuir isotherm model was founded to be the best isotherm model to describe the adsorption process. Finally, the recyclability test revealed that the composite exhibits good recycle efficiency and is stable after 5 cycles. The obtained results suggest that AC@PIN composite could be a potential candidate for the removal of MG from wastewater.