Fabrication of super-hydrophilic and highly open-porous poly (lactic acid) scaffolds using supercritical carbon dioxide foaming

Forefront Research of Foaming Strategies on Biodegradable Polymers and Their Composites by Thermal or Melt-Based Processing Technologies: Advances and Perspectives

The last few decades have witnessed significant advances in the development of polymeric-based foam materials. These materials find several practical applications in our daily lives due to their characteristic properties such as low density, thermal insulation, and porosity, which are important in packaging, in building construction, and in biomedical applications, respectively. The first foams with practical applications used polymeric materials of petrochemical origin. However, due to growing environmental concerns, considerable efforts have been made to replace some of these materials with biodegradable polymers. Foam processing has evolved greatly in recent years due to improvements in existing techniques, such as the use of supercritical fluids in extrusion foaming and foam injection moulding, as well as the advent or adaptation of existing techniques to produce foams, as in the case of the combination between additive manufacturing and foam technology. The use of supercritical CO2 is especially advantageous in the production of porous structures for biomedical applications, as CO2 is chemically inert and non-toxic; in addition, it allows for an easy tailoring of the pore structure through processing conditions. Biodegradable polymeric materials, despite their enormous advantages over petroleum-based materials, present some difficulties regarding their potential use in foaming, such as poor melt strength, slow crystallization rate, poor processability, low service temperature, low toughness, and high brittleness, which limits their field of application. Several strategies were developed to improve the melt strength, including the change in monomer composition and the use of chemical modifiers and chain extenders to extend the chain length or create a branched molecular structure, to increase the molecular weight and the viscosity of the polymer. The use of additives or fillers is also commonly used, as fillers can improve crystallization kinetics by acting as crystal-nucleating agents. Alternatively, biodegradable polymers can be blended with other biodegradable polymers to combine certain properties and to counteract certain limitations. This work therefore aims to provide the latest advances regarding the foaming of biodegradable polymers. It covers the main foaming techniques and their advances and reviews the uses of biodegradable polymers in foaming, focusing on the chemical changes of polymers that improve their foaming ability. Finally, the challenges as well as the main opportunities presented reinforce the market potential of the biodegradable polymer foam materials.

Fabrication of bio-based biodegradable poly(lactic acid) (PLA) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) composite foams for highly efficient oil-water separation

The open-cell bio-based biodegradable polymer foams show good application prospect in dealing with the serious environmental issue caused by oil spill and organic solvents spills, while the cell structures and hydrophobic properties of the foams limit their performance. In this work, the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) was selected to help prepare bio-based biodegradable poly(lactic acid) (PLA) foams. Based on a two-step foaming method, the crystallization ability of different samples was regulated by the "original crystals" together with PHBV in the foaming process, where skeleton structures were provided to facilitate the open-cell structures and promote their mechanical property. As illustrated, PHBV facilitated the formation of open-cell PLA foams, where the foams displayed superior oil-water separation capacity. The maximum volume expansion ratio of the foams was 80.08, the contact angle of deionized water reached to 134.5°, the adsorption capacity for oil or organic solvents was 10.8 g/g-51.8 g/g, and the adsorption capacity for CCl4 can still maintained 83.5 % of the initial value after 10 adsorption-desorption cycles. This work not only clarified the foaming mechanism of open-cell foams, but also provided a green and simple method for preparing bio-based biodegradable foams possessing excellent oil-water separation performance.

A Study of PLA Thin Film on SS 316L Coronary Stents Using a Dip Coating Technique

The dip coating process is one of the recognized techniques used to generate polymeric coatings on stents in an easy and low-cost way. However, there is a lack of information about the influence of the process parameters of this technique on complex geometries such as stents. This paper studies the dip coating process parameters used to provide a uniform coating of PLA with a 4-10 µm thickness. A stainless-steel tube (AISI 316L) was laser-cut, electropolished, and dip-coated in a polylactic acid (PLA) solution whilst changing the process parameters. The samples were characterized to examine the coating's uniformity, thickness, surface roughness, weight, and chemical composition. FTIR and Raman investigations indicated the presence of PLA on the stent's surface, the chemical stability of PLA during the coating process, and the absence of residual chloroform in the coatings. Additionally, the water contact angle was measured to determine the hydrophilicity of the coating. Our results indicate that, when using entry and withdrawal speeds of 500 mm min-1 and a 15 s immersion time, a uniform coating thickness was achieved throughout the tube and in the stent with an average thickness of 7.8 µm.

Biodegradable nanofibrillated microcellular PBS/PLA foams for selective oil absorption

To address the challenges posed by spilled oil and oily wastewater, the development of clean oil-adsorption materials is crucial. However, traditional oil-adsorption materials suffer from the issue of secondary pollution. Herein, fully biodegradable nanofibrillated poly(butylene succinate)/poly(lactic acid) (PBS/PLA) foams with outstanding selective oil-adsorption performance were successfully fabricated via an eco-friendly supercritical CO2 foaming technology. The PBS/PLA composites, featuring nanofibrils with a diameter of approximately 100 nm, were prepared through a hot-stretching method subsequent to extrusion. Substantial improvements were observed in the crystallization rate and rheological properties of the fibrillated PBS/PLA composites. Furthermore, PLA nanofibrils enhanced foamability of the composite, achieving an impressive expansion ratio of up to 38.0, resulting in an outstanding oil-absorption performance (19.2-50.4 g/g) of the F-1 %-95 foam. Additionally, 20 adsorption-desorption cycles illustrated the prepared F-1 %-95 foam displayed recyclable oil-absorption characteristics. This work provides an eco-friendly strategy for preparing fully biodegradable foams intended for application as oil-adsorption materials.

Mechanical, Crystallization, Rheological, and Supercritical CO2 Foaming Properties of Polybutylene Succinate Nanocomposites: Impact of Carbon Nanofiber Content

As a substitute for conventional polymers for the preparation of biodegradable microcellular polymeric foams, polybutylene succinate (PBS) presents one of the most promising alternatives. However, the low melt strength of PBS makes it difficult to produce high-performance microcellular foams. This study aimed to improve the melt strength of PBS and explore the mechanical, thermal, crystalline, rheological, and supercritical CO2 foaming properties of PBS nanocomposites by using carbon nanofibers (CNFs). This study found that nanocomposites containing 7 wt% CNF exhibited the highest tensile strength, Young's modulus, and bending strength. Moreover, the CNF nanofillers were well dispersed in the PBS matrix without significant agglomeration, even at high filler concentrations. Furthermore, the nanocomposites demonstrated improved melting temperature and crystallinity compared with pure PBS. The rheological analysis showed that the addition of CNFs significantly increased PBS viscosity at low frequencies due to the interaction between the PBS molecular chains and CNFs and the entanglement of CNFs, resulting in a more complete physical network formation when the CNF content reached above 3 wt%. During the supercritical CO2 foaming process, the addition of CNFs resulted in increased cell density, smaller cells, and thicker cell walls, with good laps formed between the fibers on the cell walls of nanocomposite foams. Moreover, the electrical conductivity and electromagnetic interference (EMI) shielding properties of the foamed material were studied, and a nanocomposite foam containing 7 wt% CNF showed good electrical conductivity (4.5 × 10-3 S/m) and specific EMI shielding effectiveness (EMI SE) (34.7 dB/g·cm-1). Additionally, the nanocomposite foam with 7 wt% CNF also exhibited good compression properties (21.7 MPa). Overall, this work has successfully developed a high-performance, multifunctional PBS-based nanocomposite foam, making it suitable for applications in various fields.

Use of Winemaking By-Products for the Functionalization of Polylactic Acid for Biomedical Applications

The addition of naturally active compounds to implantable polymers is an efficient strategy against inflammation issues that might lead to rejection, while promoting controlled re-endothelialization of the tissues. This work proposes the use of winemaking by-products with high active properties of biomedical interest to obtain bioactive PLA by using supercritical technologies. First, two red grape pomace extracts, obtained by high-pressure extraction with supercritical CO₂ and cosolvents (either ethanol or water-ethanol), have been studied. Second, two impregnation methods have been studied with both extracts, traditional supercritical CO₂-assisted impregnation (SSI) and a novel pressurized soaking method (PSI). The amount of extract impregnated as well as the bioactivity levels achieved-i.e., antioxidant, antimicrobial, and anti-inflammatory properties- have been determined for each extract and impregnation method at different pressure and temperature conditions. Both extracts obtained had good antioxidant, anti-inflammatory, and antibacterial capacities, especially the hydroethanolic one (0.50 ± 0.03 mg TE/g versus 0.24 ± 0.03 mg TE/g, respectively). Regarding impregnated filaments, impregnation loadings depended especially on the extract and P/T conditions, providing up to 8% (extract mass/polymer mass) of impregnation. The antioxidant capacity increased noteworthily by using the ethanolic extract by PSI, with values near 100 µg TE/g PLA.

High-expansion-ratio PLLA/PDLA/HNT composite foams with good thermally insulating property and enhanced compression performance via supercritical CO2

It has been a great challenge to prepare high-expansion-ratio polylactide (PLA) foam with eminent thermal insulation and compression performance in packaging field. Herein, a naturally formed nanofiller halloysite nanotube (HNT) and stereocomplex (SC) crystallites were introduced into PLA with a supercritical CO₂ foaming method to improve foaming behavior and physical properties. The compressive performance and thermal insulation properties of the obtained poly(L-lactic acid) (PLLA)/poly(D-lactic acid) (PDLA)/HNT composite foams were successfully investigated. At a HNT content of 1 wt%, the PLLA/PDLA/HNT blend foam with an expansion ratio of 36.7 folds showed a thermal conductivity as low as 30.60 mW/(m·K). Meanwhile, the compressive modulus of PLLA/PDLA/HNT foam was 115% higher than that of PLLA/PDLA foam without HNT. Moreover, the crystallinity of PLLA/PDLA/HNT foam was dramatically improved after annealing, thus the results showed that compressive modulus of the annealed foam increased by as high as 72%, while it still maintained good heat insulation with the thermal conductivity of 32.63 mW/(m·K). This work provides a green method for the preparation of biodegradable PLA foams with admirable heat resistance and mechanical performance.

Improved thermal insulation and compressive property of bimodal poly (lactic acid)/cellulose nanocomposite foams

In this work, an innovative PLA/CNF nanocomposite foam with a bimodal cell structure is prepared by a simple one-step depressurization foaming process using only supercritical carbon dioxide (ScCO₂) as the foaming agent. Only at a specific foaming temperature, PLA/CNF nanocomposites foam with a bimodal cell structure could be obtained. According to the different crystallization kinetics and nucleation efficiency of samples, it was inferred that the crystallization rate and phase interface would affect the cell structure. The prepared PLA/CNF nanocomposite foam with a bimodal cell structure had an expansion ratio as high as 20 times and thermal conductivity of 0.041 w m^-1 k^-1, which exhibited low density and excellent thermal-insulation property. Meanwhile, the PLA/CNF nanocomposite foam exhibited excellent compression performance due to the presence of CNFs, which showed promising application in packaging and construction materials.

Fabrication of PLCL Block Polymer with Tunable Structure and Properties for Biomedical Application

Biodegradable materials are pivotal in the biomedical field, where how to precisely control their structure and performance is critical for their translational application. In this study, poly(L-lactide-b-ε-caprolactone) block copolymers (bPLCL) with well-defined segment structure are obtained by a first synthesis of poly(ε-caprolactone) soft block, followed by ring opening polymerization of lactide to form poly(L-lactide acid)  hard block. The pre-polymerization allows for fabrication of bPLCL with the definite compositions of soft/hard segment while preserving the individual segment of their special soft or hard segment. These priorities make the bPLCL afford biodegradable polymer with better mechanical and biodegradable controllability than the random poly(L-lactide-co-ε-caprolactone) (rPLCL) synthesized via traditional one-pot polymerization. 10 mol% ε-caprolactone introduction can result in a formation of an elastic polymer with elongation at break of 286.15% ± 55.23%. Also, bPLCL preserves the unique crystalline structure of the soft and hard segments to present a more sustainable biodegradability than the rPLCL. The combinative merits make the pre-polymerization technique a promising strategy for a scalable production of PLCL materials for potential biomedical application.

Progress in the Preparation, Properties, and Applications of PLA and Its Composite Microporous Materials by Supercritical CO2: A Review from 2020 to 2022

The development of degradable plastic foams is in line with the current development concept of being pollution free and sustainable. Poly(lactic acid) (PLA) microporous foam with biodegradability, good heat resistance, biocompatibility, and mechanical properties can be successfully applied in cushioning packaging, heat insulation, noise reduction, filtration and adsorption, tissue engineering, and other fields. This paper summarizes and critically evaluates the latest research on preparing PLA microporous materials by supercritical carbon dioxide (scCO₂) physical foaming since 2020. This paper first introduces the scCO₂ foaming technologies for PLA and its composite foams, discusses the CO₂-assisted foaming processes, and analyzes the effects of process parameters on PLA foaming. After that, the paper reviews the effects of modification methods such as chemical modification, filler filling, and mixing on the rheological and crystallization behaviors of PLA and provides an in-depth analysis of the mechanism of PLA foaming behavior to provide theoretical guidance for future research on PLA foaming. Lastly, the development and applications of PLA microporous materials based on scCO₂ foaming technologies are prospected.

Microcellular injection molded lightweight and tough poly (L-lactic acid)/in-situ polytetrafluoroethylene nanocomposite foams with enhanced surface quality and thermally-insulating performance

High-performance microcellular polymer foams have been widely used all over the world, while the excessive usage of petroleum-based polymers caused serious environmental problems. As the eco-friendly awareness is increasing significantly, poly (L-lactic acid) (PLLA), as a typical biomass polymer, has gradually attracted widespread attention. However, the slow crystallization and poor melt strength of PLLA lead to low foaming ability and thus limiting its industrial applications. Herein, a novel and scalable strategy by coupling in-situ fibrillation and mold-opening microcellular injection molding (MOMIM) was developed to fabricate lightweight and tough PLLA/polytetrafluoroethylene (PTFE) foams. Thanks to the reticulated in-situ PTFE nanofibrils with a diameter of 100-200 nm, the crystallization and viscoelasticity of PLLA were dramatically promoted, and further contributing to its foaming ability. The expansion ratio of the MOMIM PLLA/PTFE foam was increased by 86 % compared with the regular microcellular injection molded (RMIM) PLLA foam. Moreover, the lower foam density and the toughening effect of PTFE nanofibrils resulted in the outstanding ductility of the PLLA/PTFE foams, whose tensile elongation, flexural strength, and impact strength were maximally increased by 52 %, 28 %, and 48 %, compared with PLLA foams. More importantly, the thermally-insulating performance and surface quality of PLLA/PTFE foams were also greatly improved.