Flower-, wire-, and sheet-like MnO2-deposited diatomites: Highly efficient absorbents for the removal of Cr(VI)

Influence of citrate/tartrate on chromite crystallization behavior and its potential environmental implications

The ferrite process has been developed to purify wastewater containing heavy metal ions and recycle valuable metals by forming chromium ferrite. However, organic matter has an important influence on the crystallization behavior and stability of chromite synthesized from chromium-containing wastewater. We focused on the influence and effect mechanism of two typical organic acid salts (citrate (CA) and tartrate (TA)) on the process of chromium mineralization. It was found that the presence of organic matter leads to the increase of the residual content of Cr in CA system (0.50 mmol/L) and TA system (0.61 mmol/L) in the solution, and the removal of chromium was mainly due to the surface adsorption of Fe(III) hydrolysate. The decreased crystallinity of mineralized products is ascribed to the completion of organic compounds with Fe(II) and Fe(III), which hinders the formation of ferrite precursors. There was bidentate and monodentate chelation between -COO- and metal ions in the CA system and TA system respectively, which resulted in a stronger affinity between CA and iron. This study provides the underlying mechanism for Cr(III) solid oxidation by the ferrite method in an organic matter environment and is of great significance to prevent and control chromium pollution in the environment.

Diatomite Composited with a Zeolitic Imidazolate Framework for Removing Phosphate from Water

Adsorption technology based on various adsorbents has been widely applied in wastewater treatment containing phosphate. A novel diatomite adsorbent composited with ZIF-8 (CZD) was developed for removing phosphate from water in this work. The chitosan was used to pre-modify the diatomite so that ZIF-8 could be anchored on the surface of the diatomite solidly and uniformly. The diatomite composited with ZIF-8 was then used to remove phosphate in water by an adsorption process, the process variables such as adsorption time, temperature, pH, and competitive ions were investigated. The electrostatic attraction was the primary mechanism of phosphate removal. The adsorption reached equilibrium within 90 min, and its sorption capacity increased when adsorption time and temperature increased. Especially, CZD had a rapid adsorption rate and 85% of the phosphate in the solution can be adsorbed within the first 10 min. The maximum phosphate adsorption capacities of the modified diatomite reached 13.46, 13.55, and 13.95 mg/g at 25, 35, and 45 °C, respectively. The removal efficiencies of CZD for phosphate were more than 98% and even came up to 100% at 45 °C. The adsorption isotherms fit well with the Langmuir isotherm model. The Freundlich isotherm and Temkin isotherm showed that the adsorption process is physical in nature. The kinetic data of the adsorption process were fitted by the pseudo-second-order kinetics. Thermodynamic parameters indicated that the adsorption process was endothermic. This adsorbent provided an alternative for phosphate removal on account of the high adsorption efficiency in a short time. Therefore, CZD could be a promising and eco-friendly phosphate adsorbent for wastewater treatment.

A comprehensive study on the adsorption-photocatalytic processes using CoFe2O4/SiO2/MnO2 magnetic nanocomposite as a novel photo-catalyst for removal of Cr (VI) under simulated sunlight: Isotherm, kinetic and thermodynamic studies

PURPOSE

The present study aimed to investigate the efficiency of CoFe₂O₄/SiO₂/flower-like MnO₂ nanoparticles as a catalyst for Cr (VI) adsorption-photocatalytic processes.

METHODS

The magnetic nanocomposite used was first synthesized and then characterized using TEM, SEM, EDX, XRD, FTIR, XRF and BET advanced techniques. The removal of the Cr (VI) was performed through a batch adsorption approach and the effects of sample pH (A; 2-6), initial chromate concentration (B; 50-100 ppm) and adsorbent weight to sample volume ratio (C; 1-3 mg ml^-1), hole scavenger (0.1 -0.3%w/v) and time (E; 30-60 min), to evaluate the individual and interactive effects under ultraviolet light conditions, were also studied by the central composite design in the photocatalytic process of adsorption.

RESULTS

The adsorption-photocatalytic performance of the CoFe₂O₄/SiO₂/MnO₂ composite was high in which 98.1% of Cr(VI) after 30 min of photocatalytic treatment in optimum conditions (i.e. pH = 3, catalyst concentration = 2 mg L^-1, Cr(VI) concentration = 200 mg L^-1, and hole scavenger concentration = 0.4% (w/ v), At laboratory temperature, speed = 400 rpm, under UV radiation).Under optimum conditions, Cr(VI) reductive followed pseudo-second-order kinetics and followed the Langmuir and Temkin isotherms, also, positive value of ΔH° indicates endothermic nature.

CONCLUSIONS

The results showed that the synthesized CoFe₂O₄/SiO₂/MnO₂ magnetic nanocomposite holds a great potential for use as a photocatalyst to remove Cr (VI) in adsorption reactions. It can be used as an effective catalyst in the eradication of Cr (VI) wastewater.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s40201-021-00763-1.

Cr(VI) Adsorption from Aqueous Solution by UiO-66 Modified Corncob

To adsorb hexavalent chromium (Cr(VI)) in polluted water, this paper prepared a UiO-66 (Zr6O4(OH)4(BDC)12) modified granular corncob composite adsorbent by hydrothermal method with in situ loading of UiO-66 on pretreated corncob particles. The physicochemical properties of the synthesized samples were characterized. Batch adsorption experiments were conducted to investigate the adsorption process of aqueous Cr(VI) under various conditions (different ionic strength, pH and co-existing anions). The results showed that UiO-66 was successfully loaded on the modified corncob particles. The isothermal adsorption data of Cr(VI) adsorption by the UiO-66 modified corncob fit well with the Langmuir model with the maximum adsorption capacity of Cr(VI) on UiO-66@Corn+ being 90.04 mg/g. UiO-66 loading could increase Cr(VI) adsorption capacity of Corn+. The kinetic study showed that the equilibrium time for Cr(VI) adsorption on UiO-66 modified corncob was about 180 min and the kinetic data followed the pseudo-secondary kinetic model. The Cr(VI) adsorption capacity on UiO-66@Corn+ decreased with the increasing solution pH, and the optimum pH range was 4–6. The ionic strength has little effect on the Cr(VI) adsorption capacity, but the coexistence of CO32−, SO42− and PO43− in the solution could significantly decrease the equilibrium adsorption capacity of Cr(VI). The adsorption mechanism analysis showed that Cr(VI) was adsorbed on the surface of adsorbents through electrostatic attraction and was reduced further to the less toxic Cr(III) by the electron donor on the surface of adsorbent. The electrostatic interaction was the main force affecting the adsorption of Cr(VI) by UiO-66. UiO-66@Corn+ had an excellent removal efficiency of Cr(VI) and excellent reusability. UiO-66@Corn+ could effectively remove Cr(VI) from water and have a promising application.

One-pot hydrothermal preparation of manganese-doped carbon microspheres for effective deep removal of hexavalent chromium from wastewater

Mn-doped activated carbon microspheres (MnO_x/ACS) with super-high adsorption capacities and deep removal capability for hexavalent chromium (Cr(VI)) were successfully prepared via an ammonium persulfate-assisted hydrothermal method followed by potassium oxalate activation using KMnO₄ and sucrose as raw materials. Their -physical and chemical properties, as well as those of Mn-doped non-activated carbon spheres (MnO_x/CS), were characterized by XRD, SEM, TEM, EDS-mapping, XPS, N₂ adsorption-desorption, ICP-AES, and elemental analysis. It was found that the manganese oxide (MnO_x) particles were uniformly embedded within the carbon spheres via layer-by-layer capture, and the MnO_x/ACS exhibited strong redox activity because of the multivalent nature of MnO_x, resulting in excellent adsorption performance via reduction. In particular, MnO_x/ACS-4 with a Mn content of 1.06 wt% and a specific surface area of 1405.7 m² g^-1 achieved a maximum adsorption capacity of 660.7 mg g^-1; this can reduce Cr(VI) content to less than 0.05 mg L^-1, which meets the corresponding Chinese drinking water quality standard when the initial concentration of Cr(VI) is less than 400 mg L^-1. Furthermore, this highly efficient method can be extended to prepare V-, Mo-, or W-doped carbon microspheres with significantly enhanced adsorption performance for Cr(VI) compared to bare activated carbon sphere, indicating their good application prospect for the deep removal for heavy metal ions from wastewater.

MnO2 -Based Materials for Environmental Applications

Manganese dioxide (MnO₂ ) is a promising photo-thermo-electric-responsive semiconductor material for environmental applications, owing to its various favorable properties. However, the unsatisfactory environmental purification efficiency of this material has limited its further applications. Fortunately, in the last few years, significant efforts have been undertaken for improving the environmental purification efficiency of this material and understanding its underlying mechanism. Here, the aim is to summarize the recent experimental and computational research progress in the modification of MnO₂ single species by morphology control, structure construction, facet engineering, and element doping. Moreover, the design and fabrication of MnO₂ -based composites via the construction of homojunctions and MnO₂ /semiconductor/conductor binary/ternary heterojunctions is discussed. Their applications in environmental purification systems, either as an adsorbent material for removing heavy metals, dyes, and microwave (MW) pollution, or as a thermal catalyst, photocatalyst, and electrocatalyst for the degradation of pollutants (water and gas, organic and inorganic) are also highlighted. Finally, the research gaps are summarized and a perspective on the challenges and the direction of future research in nanostructured MnO₂ -based materials in the field of environmental applications is presented. Therefore, basic guidance for rational design and fabrication of high-efficiency MnO₂ -based materials for comprehensive environmental applications is provided.

Facile Fabrication of ZnMgAl/LDH/Algae Composites as a Potential Adsorbent for Cr(VI) Ions from Water: Fabrication and Equilibrium Studies

In order to improve the adsorption capacity of natural layered double hydroxyl (LDH) materials, the natural organic sources such as algae containing hydroxyl groups, amino groups, peptide connections, and alginate structures were used to improve LDH for the preparation of ZnMgAl LDH-algae composites (LDH-Ax). The structure of prepared composites was established and characterized via various techniques such as scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The LDH-A2 sample displayed the highest efficiency for Cr(VI) removal, which reached to 99% at the optimum conditions. The prepared composite LDH-A2 showed high stability and reusability (91.7%) after five cycles. The kinetic studies revealed that the Cr uptake by LDH-A1 is described as pseudo-first order, while the case of LDH-A2 is described as pseudo-second order. This study reported that the easily synthesized LDH-Ax has an interesting environmental approval process to eliminate Cr ions from aqueous media quickly and effectively.

Naturally available diatomite and their surface modification for the removal of hazardous dye and metal ions: A review

The presence of toxic pollutants such as dyes and metal ions at higher concentrations in water is very harmful to the environment. Removal of these pollutants using diatomaceous earth or diatomite (DE) and surface-modified DE has been extensively explored due to their excellent physio-chemical properties and low cost. Therefore, naturally available DE being inexpensive, their surface modified adsorbents could be one of the potential candidates for the wastewater treatment in the future. In this context, the current review has been summarized for the removal of both pollutants i.e., dyes and metal ions by surface-modified DE using the facile adsorption process. In addition, this review is prominently focused on the various modification process of DE, their cost-effectiveness; the physio-chemical characteristics and their maximum adsorption capacity. Further, real-time scenarios of reported adsorbents were tabulated based on the cost of the process along with the adsorption capacity of these adsorbents.

Effective Sequestration of Phosphate and Ammonium Ions by the Bentonite/Zeolite Na-P Composite as a Simple Technique to Control the Eutrophication Phenomenon: Realistic Studies

A bentonite/Zeolite-P (BE/ZP) composite was synthesized by controlled alkaline hydrothermal treatment of bentonite at 150 °C for 4 h for effective sequestration of phosphate and ammonium pollutants. The composite is of 512 m²/g surface area, 387 meq/100 g ion-exchange capacity, and 5.8 nm average pore diameter. The experimental investigation reflected the strong effect of the pH value in directing the uptake behavior and the best results were attained at pH 6. The kinetic properties showed an excellent agreement for phosphate and ammonium adsorption results with the pseudo-second-order model showing equilibrium intervals of 600 and 360 min, respectively, and maximum experimental capacities of 170 and 155 mg/g, respectively. Additionally, their equilibrium modeling confirmed excellent fitness with the Langmuir hypothesis, signifying homogeneous and monolayer uptake processes with a theoretical q _max of 179.4 and 166 mg/g for phosphate and ammonium, respectively. Moreover, the calculated Gaussian adsorption energies of phosphate (0.8 kJ/mol) and ammonium (0.72 kJ/mol) suggested physisorption for them with mechanisms close to the zeolitic ion-exchange process or the coulumbic attractive forces. This was supported by the assessed thermodynamic parameters which also suggested spontaneous uptake by endothermic reaction for phosphate and exothermic reaction for ammonium. The BE/ZP composite is of excellent reusability and used for eight recyclability runs achieving removal percentages of 61.5 and 74.5% for phosphate and ammonium, respectively, in run 8. Finally, the composite was applied in the purification of sewage water and groundwater, achieving complete removal for phosphate from sewage water and ammonium from groundwater and reduction of the ammonium ions in the sewage water to 2.3 mg/L.

Green Synthesis of MnO Nanoparticles Using Abutilon indicum Leaf Extract for Biological, Photocatalytic, and Adsorption Activities

We report the synthesis of MnO nanoparticles (AI-MnO NAPs) using biological molecules of Abutilon indicum leaf extract. Further, they were evaluated for antibacterial and cytotoxicity activity against different pathogenic microbes (Escherichia coli, Bordetella bronchiseptica, Staphylococcus aureus, and Bacillus subtilis) and HeLa cancerous cells. Synthesized NAPs were also investigated for photocatalytic dye degradation potential against methylene blue (MB), and adsorption activity against Cr(VI) was also determined. Results from Scanning electron microscope (SEM), X-ray powder diffraction (XRD), Energy-dispersive X-ray (EDX), and Fourier-transform infrared spectroscopy (FTIR) confirmed the successful synthesis of NAPs with spherical morphology and crystalline nature. Biological activity results demonstrated that synthesized AI-MnO NAPs exhibited significant antibacterial and cytotoxicity propensities against pathogenic microbes and cancerous cells, respectively, compared with plant extract. Moreover, synthesized AI-MnO NAPs demonstrated the comparable biological activities results to standard drugs. These excellent biological activities results are attributed to the existence of the plant’s biological molecules on their surfaces and small particle size (synergetic effect). Synthesized NAPs displayed better MB-photocatalyzing properties under sunlight than an ultraviolet lamp. The Cr(VI) adsorption result showed that synthesized NAPs efficiently adsorbed more Cr(VI) at higher acidic pH than at basic pH. Hence, the current findings suggest that Abutilon indicum is a valuable source for tailoring the potential of NAPs toward various enhanced biological, photocatalytic, and adsorption activities. Consequently, the plant’s biological molecule-mediated synthesized AI-MnO NAPs could be excellent contenders for future therapeutic applications.

Biomedical application of manganese dioxide nanomaterials

Manganese dioxide nanomaterial is a new type of inorganic nanomaterial offering numerous advantages: simple preparation, low cost, and environmental friendliness. This review summarizes the traditional and novel synthetic methods for manganese dioxide nanomaterials and mainly discusses their potential in biomedical applications. Manganese dioxide nanomaterials are mainly used as drug carriers in tumor therapy. In recent years, the construction of multifunctional nano-platforms using manganese dioxide has gradually improved. The main mechanism is that manganese dioxide nanomaterials can combine with reactive oxygen species in the tumor microenvironment to alleviate tumor hypoxia. Manganese dioxide has also been used to quench fluorescent carbon dots in fluorescent probes. Based on the oxidation ability and catalytic activity of MnO₂, MnO₂ nanosheets are widely used to build biosensors. New research shows that manganese dioxide nanomaterials also have great potential in gene therapy and nuclear magnetic imaging.

The role of bentonite clay and bentonite clay@MnFe2O4 composite and their physico-chemical properties on the removal of Cr(III) and Cr(VI) from aqueous media

In this investigation, bentonite clay (BC) and bentonite clay@MnFe2O4 composite (BCMFC) were applied as efficient adsorbents for adsorbing Cr(III) and Cr(VI) ions from aqueous media. Different analyses such as FTIR, SEM, EDX, Map, BET, and XRD were used to characterize the adsorbents. The results showed that the removal efficiency of Cr(III) and Cr(VI) using BC were found to be 95.21 and 95.74%, while the corresponding values to the BCMFC were 97.37 and 98.65%, respectively. Also, the equilibrium and kinetic studies showed that the Freundlich isotherm model and the quasi-second-order kinetic model could better describe the equilibrium and kinetic behaviors of the adsorption process. The maximum adsorption capacity of the BC for the adsorption of Cr(III) and Cr(VI) ions were evaluated as 151.5 mg/g (25oC, pH 6, 90 min, and 1 g/L) and 161.3 mg/g (25oC, pH 3, 90 min, and 1 g/L), respectively, while the BCMFC showed the maximum capacities of 175.4 mg/g (25oC, pH 6, 60 min, and 1.5 g/L) and 178.6 mg/g (25oC, pH 3, 60 min, and 1.5 g/L) for Cr(III) and Cr(VI) ions, respectively, which were remarkable amounts. In addition, the thermodynamic study indicated that the adsorption process was physical, spontaneous, and exothermic. High removal efficiency, high chromium adsorption capacity, and low-cost magnetic adsorbent were significant features of the BCMFC for removal of Cr (III) and Cr (VI).

Effective Amendments on Cadmium, Arsenic, Chromium and Lead Contaminated Paddy Soil for Rice Safety

Contamination of paddy soils with heavy metals and metalloids poses a risk to human health through the food chain. For safe agricultural production in contaminated paddy soils, “in situ” remediation through the unavailability of heavy metals from contaminated soils was investigated in order to develop cost-effective and eco-friendly approaches for soils contaminated with complexed heavy metals (HMs) and metalloids. In the present study, the effectiveness of different soil amendments, including sulfur-containing materials (hair or cysteine), manganese compounds as an antagonist and an oxidant, zeolite and iron oxide as adsorbents, and their combinations through coating or modification, was investigated by a pot experiment with rice plants and chemical analysis. Two levels of each treatment were made, termed X1 and X2, which were a single and double dose of each treatment respectively, while CaCO3 was used as a basal and pH enhancement amendment in all treatments to identify the best combination of the above treatments in the in situ remediation of heavy metals and metalloids. The rice plants were kept under the flooded condition. Results indicated that the bioavailability of As, Cd, Cr, and Pb in soil was significantly decreased with level two (X2) of iron oxide coated with modified hairs (T7X2) followed by level two (X2) of zeolite coated with KMnO4. The iron oxide coated with modified hairs (X2) decreased the concentrations of heavy metals and metalloids in rice plants in the order Pb ˃ As ˃ Cr ˃ Cd by 81%, 80%, 79% and 46%, respectively, followed by zeolite coated with KMnO4 (X2) in the order Pb ˃ As ˃ Cr ˃ Cd by 78%, 76%, 71%, and 31%, respectively, to control. The available content of these elements in soil was decreased in the order As > Cr> Pb > Cd by 67%, 66%, 64% and 60%, respectively, through iron oxide coated with modified hairs, followed by zeolite coated with KMnO4 in the order Pb ˃ Cr ˃ Cd ˃ As by 57%, 53%, 50%, and 46%, respectively, to control, which can explain the decreased bioavailability by these amendments. In addition, the maximum shoot dry and leaf area were noticed in the pots treated with iron oxide coated with modified hairs and zeolite coated with KMnO4. There is potential to use modified hairs (MHs) with iron oxide and KMnO4-coated zeolite as soil amendments to develop a cost-effective and efficient “in situ” remediation technology for As, Cd, Pb, and Cr-contaminated rice paddy soils, especially for the soils with complex contamination by Cd and As.

Insight into the Adsorption and Photocatalytic Behaviors of an Organo-bentonite/Co3O4 Green Nanocomposite for Malachite Green Synthetic Dye and Cr(VI) Metal Ions: Application and Mechanisms

A green composite of organically modified bentonite supported by Co3O4 nanoparticles (OB/Co) was successfully fabricated and investigated as a potential eco-friendly, low-cost adsorbent and photocatalyst for promising removal of both malachite green dye (MG.D) and Cr(VI) ions. The composite showed high adsorption properties and achieved experimental q max values of 223 and 139 mg/g for MG.D and Cr(VI) after equilibration times of 360 min and 480 min for the inspected contaminants, respectively. The kinetic and equilibrium inspection reflected the best description of their adsorption behaviors by the pseudo-first-order kinetic model and the Langmuir isotherm model, respectively. This revealed favorable and homogeneous uptake of both MG.D and Cr(VI) in a monolayer form with theoretical Langmuir q max values of 343.6 and 194.5 mg/g, respectively. The theoretical adsorption energies of MG.D (0.6 kJ/mol) and Cr(VI) (0.5 kJ/mol) from the Dubinin-Radushkevich (D-R) model revealed physisorption properties that might be resulted from some types of Coulombic attractive forces, achieving theoretical q max values of 226.5 and 144.6 mg/g, respectively. The suggested adsorption mechanism was confirmed by the main mathematical parameters of thermodynamic studies that revealed physical, spontaneous, and exothermic uptake processes. Also, the composite showed high photocatalytic performance under visible light, which resulted in a 100% removal percentage of 100 mg/L of MG.D and Cr(VI) after about 180 and 240 min, respectively, from the adsorption equilibrium time.

Cr(VI) remediation from aqueous environment through modified-TiO2-mediated photocatalytic reduction

Cr(VI) exhibits cytotoxic, mutagenic and carcinogenic properties; hence, effluents containing Cr(VI) from various industrial processes pose threat to aquatic life and downstream users. Various treatment techniques, such as chemical reduction, ion exchange, bacterial degradation, adsorption and photocatalysis, have been exploited for remediation of Cr(VI) from wastewater. Among these, photocatalysis has recently gained considerable attention. The applications of photocatalysis, such as water splitting, CO2 reduction, pollutant degradation, organic transformation reactions, N2 fixation, etc., towards solving the energy crisis and environmental issues are briefly discussed in the Introduction of this review. The advantages of TiO2 as a photocatalyst and the importance of its modification for photocatalytic reduction of Cr(VI) has also been addressed. In this review, the photocatalytic activity of TiO2 after modification with carbon-based advanced materials, metal oxides, metal sulfides and noble metals towards reduction of Cr(VI) was evaluated and compared with that of bare TiO2. The photoactivity of dye-sensitized TiO2 for reduction of Cr(VI) was also discussed. The mechanism for enhanced photocatalytic activity was highlighted and attributed to the resultant properties, namely, effective separation of photoinduced charge carriers, extension of the light absorption range and intensity, increase of the surface active sites, and higher photostability. Advantages and limitations for photoreduction of Cr(VI) over modified TiO2 are depicted in the Conclusion. The various challenges that restrict the technology from practical applications in remediation of Cr(VI) from wastewater were addressed in the Conclusion section as well. The future perspectives of the field presented in this review are focused on the development of whole-solar-spectrum responsive, TiO2-coupled photocatalysts which provide efficient photocatalytic reduction of Cr(VI) along with their good recoverability and recyclability.

Nb2O5 nanowires in-situ grown on carbon fiber: A high-efficiency material for the photocatalytic reduction of Cr(VI)

Niobium oxide nanowire-deposited carbon fiber (CF) samples were prepared using a hydrothermal method with amorphous Nb₂O₅·nH₂O as precursor. The physical properties of the samples were characterized by means of numerous techniques, including X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), UV-visible spectroscopy (UV-vis), N₂ adsorption-desorption, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy. The efficiency for the removal of Cr(VI) was determined. Parameters such as pH value and initial Cr(VI) concentration could influence the Cr(VI) removal efficiency or adsorption capacity of the Nb₂O₅/carbon fiber sample obtained after hydrothermal treatment at 160°C for 14hr. The maximal Cr(VI) adsorption capacity of the Nb₂O₅ nanowire/CF sample was 115mg/g. This Nb₂O₅/CF sample also showed excellent photocatalytic activity and stability for the reduction of Cr(VI) under UV-light irradiation: the Cr(VI) removal efficiency reached 99.9% after UV-light irradiation for 1hr and there was no significant decrease in photocatalytic performance after the use of the sample for 10 repeated cycles. Such excellent Cr(VI) adsorption capacity and photocatalytic performance was related to its high surface area, abundant surface hydroxyl groups, and good UV-light absorption ability.

Ultrasonication synthesis of PVA/PVP/α-MnO2-stearic acid blend nanocomposites for adsorbing CdII ion

In this research, the functionalization of α-MnO₂ nanorods (NRs) was conducted with stearic acid (SA) through solvothermal technique. The α-MnO₂-SA NRs were used as nanofiller for the preparation of blend nanocomposites (NCs) based on poly(vinyl alcohol) (PVA) and poly(vinyl pyrrolidone) (PVP) by ultrasonic irradiation. The results exhibit that with increasing in α-MnO₂-SA quantity, the thermal stability of blend NCs was improved. Morphological studies revealed that α-MnO₂-SA with rod structure and a diameter size of 25-80nm was uniformly dispersed in the PVA and PVP matrices. The use of ultrasonic was responsible for these great homogeneities which could not be achieved by mechanical or magnetically stirring. The prepared blend NCs were exploited as an adsorbing for uptake of Cd^II ion from the aqueous system. The results indicated that they can be potentially utilized for the elimination of Cd^II ion from an aqueous system with q_m of 47(mgg^-1).

Use of PVA/α-MnO2-stearic acid nanocomposite films prepared by sonochemical method as a potential sorbent for adsorption of Cd (II) ion from aqueous solution

Alpha manganese dioxide (α-MnO₂) nanorods have been covalently functionalized with stearic acid by solvothermal method. The α-MnO₂-stearic acid nanorods were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. The amount of stearic acid grafted onto α-MnO₂ surface was determined about 41wt% by thermogravimetric analysis. The α-MnO₂-stearic acid nanorods was used as nanofiller for the preparation of poly(vinyl alcohol) (PVA) nanocomposites (NCs). The NCs with 1, 3, and 5wt% of nanofiller were prepared through ultrasound assisted technique as an economical, fast, eco-friendly, and effective method. The PVA/α-MnO₂-stearic acid NCs were characterized by different techniques. The results showed that with increasing the α-MnO₂-stearic acid content, the thermal stability and tensile properties were improved. Besides, the NC 5wt% was used as adsorbent for sorption of Cd (II) ion. The adsorption efficiency of NC 5wt% in different initial concentrations of Cd (II) ion (20-100mgL^-1) was 58-95%. All the isotherm data were well fitted by both Langmuir and Freundlich equations. The adsorption kinetics study demonstrated that pseudo-second-order model was the best fit with the experimental data. The results indicated that prepared NCs are promising adsorbents for the removal of Cd (II) ion from the aqueous solution.

FeOOH-loaded MnO2 nano-composite: An efficient emergency material for thallium pollution incident

A FeOOH-loaded MnO₂ nano-composite was developed as an emergency material for Tl(I) pollution incident. Structural characterizations showed that FeOOH successfully loaded onto MnO₂, the nanosheet-flower structure and high surface area (191 m² g^-1) of material contributed to the excellent performance for Tl(I) removal. FeOOH-loaded MnO₂ with a Fe/Mn molar ratio of 1:2 exhibited a noticeable enhanced capacity for Tl(I) removal compared to that of pure MnO₂. The outstanding performance for Tl(I) removal involves in extremely high efficiency (achieved equilibrium and drinking water standard within 4 min) and the large maximum adsorption capacity (450 mg g^-1). Both the control-experiment and XPS characterization proved that the removal mechanism of Tl(I) on FeOOH-loaded MnO₂ included adsorption and oxidation: the oxidation of MnO₂ played an important role for Tl(I) removal, and the adsorption of FeOOH loaded on MnO₂ enhanced Tl(I) purification at the same time. In-depth purification of Tl(I) had reach drinking water standards (0.1 μg L^-1) at pH above 7, and there wasn't security risk produced from the dissolution of Mn²⁺ and Fe²⁺. Moreover, the as-prepared material could be utilized as a recyclable adsorbent regenerated by using NaOH-NaClO binary solution. Therefore, the synthesized FeOOH-loaded MnO₂ in this study has the potential to be applied as an emergency material for thallium pollution incident.

Facile synthesis of hierarchical mesoporous weirds-like morphological MnO2 thin films on carbon cloth for high performance supercapacitor application

The mesoporous nanostructured metal oxides have a lot of capabilities to upsurge the energy storing capacity of the supercapacitor. In present work, different nanostructured morphologies of MnO₂ have been successfully fabricated on flexible carbon cloth by simple but capable hydrothermal method at different deposition temperatures. The deposition temperature has strong influence on reaction kinetics, which subsequently alters the morphology and electrochemical performance. Among different nanostructured MnO₂ thin films, the mesoporous weirds composed thin film obtained at temperature of 453K exhibits excellent physical and electrochemical features for supercapacitor application. The weirds composed MnO₂ thin film exhibits specific surface area of 109m²g^-1, high specific capacitance of 595Fg^-1 with areal capacitance of 4.16Fcm^-2 at a scan rate of 5mVs^-1 and high specific energy of 56.32Whkg^-1. In addition to this, MnO₂ weirds attain capacity retention of 87 % over 2000 CV cycles, representing better cycling stability. The enhanced electrochemical performance could be ascribed to direct growth of highly porous MnO₂ weirds on carbon cloth which provide more pathways for easy diffusion of electrolyte into the interior of electroactive material. The as-fabricated electrode with improved performance could be ascribed as a potential electrode material for energy storage devices.

Superb adsorption capacity of hierarchical calcined Ni/Mg/Al layered double hydroxides for Congo red and Cr(VI) ions

The preparation of hierarchical porous materials as catalysts and sorbents has attracted much attention in the field of environmental pollution control. Herein, Ni/Mg/Al layered double hydroxides (NMA-LDHs) hierarchical flower-like hollow microspheres were synthesized by a hydrothermal method. After the NMA-LDHs was calcined at 600°C, NMA-LDHs transformed into Ni/Mg/Al layered double oxides (NMA-LDOs), which maintained the hierarchical flower-like hollow structure. The crystal phase, morphology, and microstructure of the as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy elemental mapping, Fourier transform infrared spectroscopy, and nitrogen adsorption-desorption methods. Both the calcined and non-calcined NMA-LDHs were examined for their performance to remove Congo red (CR) and hexavalent chromium (Cr(VI)) ions in aqueous solution. The maximum monolayer adsorption capacities of CR and Cr(VI) ions over the NMA-LDOs sample were 1250 and 103.4mg/g at 30°C, respectively. Thermodynamic studies indicated that the adsorption process was endothermic in nature. In addition, the addition of coexisting anions negatively influenced the adsorption capacity of Cr(VI) ions, in the following order: CO₃^2->SO₄^2->H₂PO₄^->Cl^-. This work will provide new insight into the design and fabrication of advanced adsorption materials for water pollutant removal.

Covalent surface modification of α-MnO2 nanorods with l-valine amino acid by solvothermal strategy, preparation of PVA/α-MnO2-l-valine nanocomposite films and study of their morphology, thermal, mechanical, Pb(ii) and Cd(ii) adsorption properties

The surface of α-manganese dioxide (α-MnO₂) nanorods was modified chemically with l-valine amino acid by a solvothermal strategy.

Cr(vi) removal by combined redox reactions and adsorption using pectin-stabilized nanoscale zero-valent iron for simulated chromium contaminated water

Pectin-stabilized nanoscale zero-valent iron was used to removal Cr(vi) and the main mechanisms were redox reaction and adsorption.