Effect of particle size of sugar beet pulp on the extraction and property of pectin

Experimental investigation on the carob extraction using arrhenius approach and response surface

Environmental problems have increased the need for sustainable agricultural practices that conserve water and energy. Carob, an eco-friendly crop with multiple health benefits, holds the potential for economic evaluation. This study investigates the carob molasses extraction process, focusing on the influence of temperature and water quantity on the diffusion coefficient. The rheological behavior of carob molasses was analyzed experimentally, and a model was developed to optimize energy consumption during the extraction process. The impact of temperature on the mass transfer coefficient was examined using the Arrhenius approach, with the extraction conducted at a maximum of 50 °C to prevent caramelization. The activation energy for carob extraction was determined to be 5.475 kJ/mol, and a new equation is proposed for estimating the mass transfer coefficient.

Differences in physicochemical properties of pectin extracted from pomelo peel with different extraction techniques

In order to obtain high yield pomelo peel pectin with better physicochemical properties, four pectin extraction methods, including hot acid extraction (HAE), microwave-assisted extraction (MAE), ultrasound-assisted extraction, and enzymatic assisted extraction (EAE) were compared. MAE led to the highest pectin yield (20.43%), and the lowest pectin recovery was found for EAE (11.94%). The physicochemical properties of pomelo peel pectin obtained by different methods were also significantly different. Pectin samples obtained by MAE had the highest methoxyl content (8.35%), galacturonic acid content (71.36%), and showed a higher apparent viscosity, thermal and emulsion stability. The pectin extracted by EAE showed the highest total phenolic content (12.86%) and lowest particle size (843.69 nm), showing higher DPPH and ABTS scavenging activities than other extract methods. The pectin extracted by HAE had the highest particle size (966.12 nm) and degree of esterification (55.67%). However, Fourier-transform infrared spectroscopy showed that no significant difference occurred among the different methods in the chemical structure of the extracted pectin. This study provides a theoretical basis for the industrial production of pomelo peel pectin.

Hot-air drying vs. lyophilization of sugar beet flakes for efficient pectin recovery and influence of extraction conditions on pectin physicochemical properties

This study assessed the influence of drying pretreatment and extraction conditions (type of acid and particle size of plant material) on the yield and physicochemical properties of pectin from sugar beet flakes resulted as by-product of sugar beet processing in the sugar industry. The results indicated that the drying conditions (hot-air drying and lyophilization) affected the extraction yield, the chemical composition of pectin, its color, degree of methylation and acetylation, molecular weight, and its rheological and emulsifying properties. The best results for pectin yield (16.20%), galacturonic acid content (91.19 g/100 g), degree of methylation and acetylation (66.93 and 23.87%), and molecular weight (3.89 × 105 g/mol) were obtained when sugar beet flakes were pretreated by hot-air drying, and the extraction was made with citric acid using plant material with particle sizes of 125-200 μm. This pectin also had high emulsion activity (51.42%) and emulsion stability (88.03%). The FT-IR spectra were similar, while pectin thermal behavior was affected by the drying pretreatment and extraction conditions. The results of this study showed that from this by-product of the sugar industry it can be extracted high quality pectin with rheological and emulsifying properties that are superior to commercial citrus and apple pectin.

Extraction of high methoxyl pectin from unripe waste Ponkan mandarine (Citrus reticulata Blanco cv. Ponkan) with an eco-friendly solvent

The aqueous batch extraction of pectin from unripe Ponkan mandarin was evaluated for potential application in the food industry. A small central composite design with 4 variables (temperature, volume to mass ratio, pH, and mean particle size) and 3 levels was applied for pectin extraction optimization. Also, the kinetic of the pectin yield extraction was investigated at temperatures 70-90 °C, stirring rate of 100-700 rpm, ultrasound pretreatment system, and modeling using four mathematical models. The pectin extraction process was evaluated by yield of pectin and esterification degree. FTIR, TGA, and DTA were performed to evaluate the quality of pectin obtained. The small central composite design demonstrated that temperature and volume to mass ratio were significant variables, and the highest yield of pectin extraction was 11.62 % obtained at temperature and volume to molar ratio of 81.9 °C and 33.9 v/w %, respectively. Besides, the esterification degree showed higher than 70 % for all extraction conditions, suggesting high methoxyl pectin. The kinetics showed the stirring rate and the ultrasound pretreatment did not cause any significant alteration, while high temperatures proved to be beneficial to the rate and the yield of the pectin extraction. The best fit was provided by Fick's law, suggesting the extraction process is limited by internal mass transfer. FTIR showed the functional groups expected for pectin, and TGA and DTA indicated that the pectin obtained is proper for most food products, as only above 200 °C the pectin should degrade.

Eat your beets: Conversion of polysaccharides into oligosaccharides for enhanced bioactivity

Bioactive oligosaccharides with the potential to improve human health, especially in modulating gut microbiota via prebiotic activity, are available from few natural sources. This work uses polysaccharide oxidative cleavage to generate oligosaccharides from beet pulp, an agroindustry by-product. A scalable membrane filtration approach was applied to purify the oligosaccharides for subsequent in vitro functional testing. The combined use of nano-LC/Chip Q-TOF MS and UHPLC/QqQ MS allowed the evaluation of the oligosaccharide profile and their monosaccharide complexity. A final product containing roughly 40 g of oligosaccharide was obtained from 475 g of carbohydrates. Microbiological bioactivity assays indicated that the product obtained herein stimulated desirable commensal gut bacteria. This rapid, reproducible, and scalable method represents a breakthrough in the food industry for generating potential prebiotic ingredients from common plant by-products at scale. INDUSTRIAL RELEVANCE: This work proposes an innovative technology based on polysaccharide oxidative cleavage and multi-stage membrane purification to produce potential prebiotic oligosaccharides from renewable sources. It also provides critical information to evidence the prebiotic potential of the newly generated oligosaccharides on the growth promotion ability of representative probiotic strains of bifidobacteria and lactobacilli.

Fermentation development using fruit waste derived mixed sugars for poly(3-hydroxybutyrate) production and property evaluation

Free sugars from fruit wastes were evaluated for the production of poly(3-hydroxybutyrate) (PHB) in Paraburkholderia sacchari fed-batch bioreactor fermentations. Different initial sugar concentration, carbon to inorganic phosphorus (C/IP) ratio, IP addition during feeding and volumetric oxygen transfer coefficient (k_La) were evaluated to promote PHB production. The highest intracellular PHB accumulation (66.6%), PHB concentration (108.3 g/L), productivity (3.28 g/L/h) and yield (0.33 g/g) were achieved at 40 g/L initial sugars, C/IP 26.5, 202.6 h^-1k_La value and 20% IP supplementation in the feeding solution. The effect of different cell's harvesting time on PHB properties showed no influence in weight average molecular weight and thermal properties. The harvest time influenced the tensile strength that was reduced from 28.7 MPa at 22 h to 13.3 MPa at 36 h. The elongation at break and Young's modulus were in the range 3.6-14.8% and 830-2000 MPa, respectively.

Roles of physical fields in the extraction of pectin from plant food wastes and byproducts: A systematic review

Pectin is a naturally occurring hydrocolloid found in the cell wall and middle lamella of many plants and has numerous functional applications in food and other related industries. The type of extraction methods used in production has a strong influence on the structural or physicochemical properties of the resultant pectin and the potential application or market value of the produced pectin. Many conventional extraction methods are well-established and commercially well adopted. However, the increased demand for pectin due to limitations of the existing methods in terms of efficiency and influence on end product quality has been renewed in developing novel techniques or procedures that help to alleviate these problems. In this review paper, a series of strategies involving the application of physical fields, such as acoustic, electromagnetic, electric and mechanical one, are reviewed for potential opportunities to improve the yield and quality attributes of pectin extracted from plant food wastes and byproducts. The extraction mechanism, processing equipment, key operating parameters as well as advantages and disadvantages of each method are systematically reviewed, and findings and conclusions on the potential applications of each method are described. Moreover, the challenges and future directions of physical field assisted extraction (PFAE) of pectin are also discussed to facilitate a better understanding of the complex mechanism in PFAE and optimizing operational parameters. This review may also provide specific theoretical information and practical applications to improve the design and scale up PFAE of pectin.

Hybrid techniques of pre and assisted processing modify structural, physicochemical and functional characteristics of okra pectin: Controlled-temperature ultrasonic-assisted extraction from preparative dry powders and its field monitoring

Diversiform okra dry powders were prepared and controlled-temperature ultrasonic-assisted extraction (CTUAE) was then utilized to obtain okra pectin (OP) from the preparative powders. During processing of hybrid techniques, 6 types of dry powders were prepared through different drying technologies (hot air drying, HD; freeze-drying, FD) and meshes (60, 80, 120 meshes) at first. Next, the extraction yield, physicochemical and function characteristics, and molecular structure of OP were analyzed with or without CTUAE technique. Meanwhile, the time-frequency domains of acoustic fields during extraction process of OP were monitored to analyze the effects of ultrasonic fields. Results showed that OP main chains with less cracking by FD than that by HD; the yield, GalA, esterification degree (DE), M_w and viscosity of OP increased, but its particle size decreased. Water holding capacity (WHC) and oil holding capacity (OHC) of OP by HD were more prominent. Secondly, HD OP had dendritic rigid chains, while FD OP had flexible chains with multiple branches. For HD OP, as meshes of okra dry powders decreased, GalA, viscosity and emulsification ability decreased; while gel strength and thermal stability increased. For FD OP, the reduction of meshes improved thermal stability. Above all, CTUAE technique increased the yield and GalA, and decreased DE, M_w and particle size of OP. In terms of functional characteristics, the technique also improved gel strength, resilience and viscoelasticity, enhanced emulsifying stability, WHC and thermal stability, and reduced viscosity. Finally, the correlation between functional and structural characteristics of OP was quantified, and some suggestions were made for its application in food areas.

Extraction techniques in food industry: Insights into process parameters and their optimization

This review presents critical evaluation of the key parameters that affect the extraction of targeted components, giving due consideration to safety and environmental aspects. The crucial aspects of the extraction technologies along with protocols and process parameters for designing unit operations have been emphasized. The parameters like solvent usage, substrate type, concentration, particle size, temperature, quality and storage of extract as well as stability of extraction have been elaborately discussed. The process optimization using mathematical and computational modeling highlighting information and communication technologies have been given importance aiming for a green and sustainable industry level scaleup. The findings indicate that the extraction processes vary significantly depending on the category of food and its structure. There is no single extraction method or universal set of process conditions identified for extracting all value-added products from respective sources. A comprehensive understanding of process parameters and their optimization as well as synergistic combination of multiple extraction processes can aid in enhancement of the overall extraction efficiency. Future efforts must be directed toward the design of integrated unit operations that cause minimal harm to the environment along with investigations on economic feasibility to ensure sustainable extraction systems.

The Influence of Extraction Conditions on the Yield and Physico-Chemical Parameters of Pectin from Grape Pomace

Grape pomace is one of the most abundant by-products generated from the wine industry. This by-product is a complex substrate consisted of polysaccharides, proanthocyanidins, acid pectic substances, structural proteins, lignin, and polyphenols. In an effort to valorize this material, the present study focused on the influence of extraction conditions on the yield and physico-chemical parameters of pectin. The following conditions, such as grape pomace variety (Fetească Neagră and Rară Neagră), acid type (citric, sulfuric, and nitric), particle size intervals (<125 µm, ≥125−<200 µm and ≥200−<300 µm), temperature (70, 80 and 90 °C), pH (1, 2 and 3), and extraction time (1, 2, and 3 h) were established in order to optimize the extraction of pectin. The results showed that acid type, particle size intervals, temperature, time, and pH had a significant influence on the yield and physico-chemical parameters of pectin extracted from grape pomace. According to the obtained results, the highest yield, galacturonic acid content, degree of esterification, methoxyl content, molecular, and equivalent weight of pectin were acquired for the extraction with citric acid at pH 2, particle size interval of ≥125−<200 µm, and temperature of 90 °C for 3 h. FT-IR analysis confirmed the presence of functional groups in the fingerprint region of identification for polysaccharide in the extracted pectin.

Beet pulp dietary fiber exposed to an extremely low-frequency electromagnetic field: detoxification properties

Introduction. The lack of dietary fibre in the Russian people diet contributes to the development of various diseases. In this regard, it seems worthwhile to enrich foods with dietary fibre obtained from various types of raw materials. In our experiments, we used beet pulp. This study aimed to develop a technology for obtaining combined dietary fibre using the electrophysical method and evaluate its detoxification properties. Study objects and methods. Study objects were pectin substances and combined detoxicants from beet pulp obtained by extracting with succinic acid with and without an extremely low-frequency electromagnetic field (ELF EM) treatment. The profiles of combined detoxicants and pectin substances were identified by IR-Fourier spectrometry. Beet pectin, beet cellulose, and their combined detoxicants were tested for complexing (binding) capacity with respect to lead ions (Pb2+). For this, we applied the trilonometric method with some modifications. Results and discussion. The analysis of the absorption bands of carboxyl groups carbonyls revealed the presence of free carboxyl groups in the combined detoxicants. The combined detoxicant with a 1:0.5 ratio of cellulose and pectin substances showed a high complexing (binding) capacity (601 mg/Pb2+) with respect to lead ions (Pb2+). Conclusion. We developed a technology for producing combined detoxicants with a high complexing capacity with respect to lead ions analysed microstructures of gels obtained during the interaction between the combined detoxicant and lead acetate solution.

Effects of different extraction methods on structural and physicochemical properties of pectins from finger citron pomace

The functionality and property of pectin are correlated with its structure which is affected by the extraction method used. In this study, three different methods of extracting pectin, the microwave-assisted extraction (MAE), the ultrasonic-assisted extraction (UAE) and the conventional heating extraction (CHE), were used at three different temperatures with both an acid and alkali extraction solution. It was found that temperature mainly influenced pectin yield, while pectin structures and physicochemical properties were affected by the pH condition and extraction technology. The alkali-extraction with MAE and UAE at short time promoted the yield of low-ester pectin. Monosaccharide composition analysis showed a high galacturonic acid (GalA) content in the pectin derived from MAE and UAE. The high viscosity and desirable viscoelastic properties of the acid-MAE pectin were due to its large molecular weight and particle size. The results contribute to our understanding of the association among pectin extraction, structure and properties.

Physicochemical, Thermal and Rheological Properties of Pectin Extracted from Sugar Beet Pulp Using Subcritical Water Extraction Process

The objective of this study was to characterize the properties of pectin extracted from sugar beet pulp using subcritical water (SWE) as compared to conventional extraction (CE). The research involved advanced modeling using response surface methodology and optimization of operational parameters. The optimal conditions for maximum yield of pectin for SWE and CE methods were determined by the central composite design. The optimum conditions of CE were the temperature of 90 °C, time of 240 min, pH of 1, and pectin recovery yield of 20.8%. The optimal SWE conditions were liquid-to-solid (L/S) ratio of 30% (v/w) at temperature of 130 °C for 20 min, which resulted in a comparable yield of 20.7%. The effect of obtained pectins on viscoamylograph pasting and DSC thermal parameters of corn starch was evaluated. The contents of galacturonic acid, degree of methylation, acetylation, and ferulic acid content were higher in the pectin extracted by SWE, while the molecular weight was lower. Similar chemical groups were characterized by FTIR in both SWE and CE pectins. Color attributes of both pectins were similar. Solutions of pectins at lower concentrations displayed nearly Newtonian behavior. The addition of both pectins to corn starch decreased pasting and DSC gelatinization parameters, but increased ΔH. The results offered a promising scalable approach to convert the beet waste to pectin as a value-added product using SWE with improved pectin properties.

Effect of superfine grinding on the physicochemical properties of bulbs of Fritillaria unibracteata Hsiao et K.C. Hsia powder

This work aimed to determine the influence of superfine grinding on the physicochemical properties of bulbs of Fritillaria unibracteata Hsiao et K.C. Hsia (BFU) powder. For this purpose, fine powder (FP) and two superfine powders (SPs) were obtained via superfine and conventional grinding methods. The properties of different powders were studied and compared. Compared with FP, SPs exhibited higher values in terms of the angle of repose, swelling capacity, ethanol extraction yield, total alkaloid content, and imperialine content, while lower values in terms of particle size and bulk density. Especially, the total alkaloid content of SP-I increased by 66.7%. Proper grinding is more conducive to reduce particle size and improve alkaloid content. FTIR analysis indicates that no new functional groups produced after superfine grinding. XRD analysis suggests that grinding treatment lead to decreases in the crystallinity. Therefore, superfine grinding displays immense potential in the BFU application.

Structural and Rheological Properties of Pectins Extracted from Industrial Sugar Beet By-Products

In this work, the efficient extraction of pectin from sugar beet by-products (pressed, ensiled and dried pulp), by using an acid method or a commercial cellulose, is accomplished. The extraction method had an impact on the pectin monomeric composition, mainly in xylose, arabinose, and galacturonic acid content, as determined by GC-FID. FTIR and SEC analyses allowed the determination of similar degrees of methoxylation and molecular weights, respectively, in the extracted pectins. The acid extraction of pectin in the ensiled by-product led to the highest yield (19%) with a galacturonic acid content of 46%, whereas the application of the enzymatic extraction method resulted in a lower yield (13%) but higher galacturonic acid content (72%). Moreover, the stability in aqueous solution as well as the emulsifying activity index was higher for pectin extracted by the acid method, whereas the viscosity was higher in pectin extracted by the enzymatic method. To the best of our knowledge, this is the first study analyzing the physicochemical properties and exploring the potential reuse of ensiled and dried by-products from sugar beet industry for the extraction of pectin to be further used in the food and pharmaceutical areas.