Studies on adsorption of mercury from aqueous solution on activated carbons prepared from walnut shell

Mechanistic Evidence for Hg Removal from Wastewater by Biologically Produced Sulfur

A significant quantity of biologically produced sulfur (BPS) is generated as a by-product of chemical and biological desulfurization processes applied to landfill gas treatment. The beneficial upcycling of BPS has seen limited use in the environmental context. The effectiveness and underlying mechanism of BPS as an adsorbent for removing Hg2+ from both solution and wastewater were elucidated based on experiments encompassing surface characterization, adsorption isotherms, kinetics, and thermodynamics. The BPS exhibited remarkable efficacy in removing Hg2+ from solution, with the Langmuir model accurately describing the adsorption process and showing a maximum adsorption capacity of 244 mg g-1. Surface analysis through X-ray photoelectron spectroscopy and scanning electron microscopy revealed that Hg2+ complexed with sulfide on BPS surfaces, forming stable HgS. The adsorbed Hg was strongly retained in BPS, with less than 0.2% of the adsorbed Hg desorbed by strong acids. Adsorption kinetics followed the double-exponential first-order model, showing an initial rapid adsorption phase wherein 75% of the initial Hg2+ was removed within 5 min, followed by a slower adsorption rate. The thermodynamic parameters suggested that adsorption of Hg2+ by BPS was a spontaneous and endothermic process. Additionally, BPS effectively removed Hg2+ from wastewater, showing preference for Hg over other co-existing metals. These findings underscore the potential of BPS as an effective adsorbent for Hg2+ removal from wastewater.

Enhanced benzene vapor adsorption through microwave-assisted fabrication of activated carbon from peanut shells using ZnCl2 as an activating agent

Herein, microwave-assisted activated carbon (MW-AC) was fabricated from peanut shells using a ZnCl2 activator and utilized for the first time to eliminate benzene vapor as a volatile organic compound (VOC). During the MW-AC production process, which involved two steps-microwave treatment and muffle furnace heating-we investigated the effects of various factors and achieved the highest iodine number of 1250 mg/g. This was achieved under optimal operating conditions, which included a 100% impregnation ratio, CO2 as the gas in the microwave environment, a microwave power set at 500 W, a microwave duration of 10 min, an activation temperature of 500 °C and an activation time of 45 min. The structural and morphological properties of the optimized MW-AC were assessed through SEM, FTIR, and BET analysis. The dynamic adsorption process of benzene on the optimized MW-AC adsorbent, which has a significant BET surface area of 1204.90 m2/g, was designed using the Box-Behnken approach within the response surface methodology. Under optimal experimental conditions, including a contact duration of 80 min, an inlet concentration of 18 ppm, and a temperature of 26 °C, the maximum adsorption capacity reached was 568.34 mg/g. The experimental data are better described by the pseudo-second-order kinetic model, while it is concluded that the equilibrium data are better described by the Langmuir isotherm model. MW-AC exhibited a reuse efficiency of 86.54% for benzene vapor after five consecutive recycling processes. The motivation of the study highlights the high adsorption capacity and superior reuse efficiency of MW-AC adsorbent with high BET surface area against benzene pollutant. According to our results, the developed MW-AC presents itself as a promising adsorbent candidate for the treatment of VOCs in various industrial applications.

A review on adsorption of heavy metals from wastewater using carbon nanotube and graphene-based nanomaterials

The rampant rise in world population, industrialization, and urbanization expedite the contamination of water sources. The presence of the non-biodegradable character of heavy metals in waterways badly affects the ecological balance. In this modern era, the unavailability of getting clear water as well as the downturn in water quality is a major concern. Therefore, the effective removal of heavy metals has become much more important than before. In recent years, the attention to better wastewater remediation was directed towards adsorption techniques with novel adsorbents such as carbon nanomaterials. This review paper primarily emphasizes the fundamental concepts, structures, and unique surface properties of novel adsorbents, the harmful effects of various heavy metals, and the adsorption mechanism. This review will give an insight into the current status of research in the realm of sustainable wastewater treatment, applications of carbon nanomaterials, different types of functionalized carbon nanotubes, graphene, graphene oxide, and their adsorption capacity. The importance of MD simulations and density functional theory (DFT) in the elimination of heavy metals from aqueous media is also discussed. In addition to that, the effect of factors on heavy metal adsorption such as electric field and pressure is addressed.

Selective removal of Hg(II) by UiO-66-NH2 modified by 4-quinolinecarboxaldehyde: from experiment to mechanism

In wastewater, heavy metal Hg causes serious harm to ecology, so it needs to be removed. In this paper, a novel MOF adsorbent (UiO-66-QU) was prepared by modifying UiO-66-NH₂ with 4-quinolinecarboxaldehyde, which was used to selectively remove Hg(II) from water. The adsorbent was characterized using Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), zeta potentiometer, and X-ray photoelectron spectroscopy (XPS). In order to investigate the Hg(II) adsorption performance of UiO-66-QU, the effect of time, initial concentration, pH, and temperature were carried out. Langmuir model fitting shows that the maximum adsorption capacity of UiO-66-QU for Hg(II) is 556 mg/g at 298 K. The experimental results show that UiO-66-QU has better Hg(II) adsorption capacity than UiO-66-NH₂. The isotherm is in accordance with pseudo-second-order models. It is indicated that the adsorption process is mainly monolayer chemical adsorption. The thermodynamic parameters also indicate that the adsorption process is spontaneous and endothermic. It has excellent reusability and selectivity. XPS and the zeta potential showed that the adsorption mechanism was the complex reaction of Hg(II) with nitrogenous group. Therefore, the adsorbent has potential application prospects in removal of Hg(II) from wastewater.

Highly efficient Hg2+ removal via a competitive strategy using a Co-based metal organic framework ZIF-67

The stronger coordination ability of mercury ions with organic ligands than the metal ions in metal organic framework (MOFs) provides an accessible way to separate mercury ions from solution using specific MOFs. In this study, a Co-based MOF (ZIF-67, Co(mIM)₂) was synthesized. It did not introduce specific functional groups, such as -SH and -NH₂, into its structure through complicated steps. It separate Hg²⁺ from wastewater with a new strategy, which utilized the stronger coordination ability of Hg²⁺ with the nitrogen atom on the imidazole ring of the organic ligand than the Co²⁺ ions. Hg²⁺ replaced Co²⁺ nodes from ZIF-67 and formed a more stable precipitate with mIM. The experimental results showed that this new strategy was efficient. ZIF-67 exhibited Hg²⁺ adsorption capacity of 1740 mg/g, much higher than the known MOFs sorbents. mIMs is the reaction center and ZIF-67 can improve its utilization. The sample color faded from purple to white due to the loss of cobalt ion. It is a great feature of ZIF-67 that allows users to judge whether the sorbent is deactivated intuitively. ZIF-67 can be sustainable recycled by adding organic ligands to the solution after treatment due to its simple synthesis method at room temperature. It's a high-efficient and sustainable sorbent for Hg²⁺ separation from wastewater.

Graphene Oxide/Polyethylenimine Aerogels for the Removal of Hg(II) from Water

This article reports the synthesis of an aerogel involving reduced graphene oxide (rGO) and polyethylenimine (PEI), and describes its potential application as an effective sorbent to treat Hg(II) contaminated water. The rGO/PEI sorbent was synthetized using a supercritical CO₂ method. N₂ physisorption, electron microscopy, and elemental mapping were applied to visualize the meso/macroporous morphology formed by the supercritical drying. The advantages of the synthetized materials are highlighted with respect to the larger exposed GO surface for the PEI grafting of aerogels vs. cryogels, homogeneous distribution of the nitrogenated amino groups in the former and, finally, high Hg(II) sorption capacities. Sorption tests were performed starting from water solutions involving traces of Hg(II). Even though, the designed sorbent was able to eliminate almost all of the metal from the water phase, attaining in very short periods of time residual Hg(II) values as low as 3.5 µg L⁻¹, which is close to the legal limits of drinking water of 1–2 µg L⁻¹. rGO/PEI exhibited a remarkably high value for the maximum sorption capacity of Hg(II), in the order of 219 mg g⁻¹. All of these factors indicate that the designed rGO/PEI aerogel can be considered as a promising candidate to treat Hg(II) contaminated wastewater.

Advanced Material-oriented Biomass Precise Reconstruction: A Review on Porous Carbon with Inherited Natural Structure and Created Artificial Structure by Post-treatment

Manufacturing of porous carbon with biomass resources has been intensively investigated in recent decades. The diversity of biomass species and great variety of processing methods enable the structural richness of porous carbon as well as their wide applications. In this review, we specifically focused on the structure of biomass-derived porous carbon either inherited from natural biomass or created by post-treatment. The intrinsic structure of plant biomass was briefly introduced and the utilization of the unique structures at different length-scales were discussed. In term of post-treatment, the structural features of activated carbon by traditional physical and chemical activation were summarized and compared in a wide spectrum of biomass species, statistical analysis were performed to evaluate the effectiveness of different activation methods in creating specific pore structures. The similar pore structure of biomass-derived carbon and coal-derived carbon suggested a promising replacement with more sustainable biomass resources in producing porous carbon. In summary, using biomass as porous carbon precursor endows the flexibility of using its naturally patterned micro-structure and the tunability of controlled pore-creation by post treatment. This article is protected by copyright. All rights reserved.

Aptamer-functionalized and silver-coated polydopamine-copper hybrid nanoflower adsorbent embedded with magnetic nanoparticles for efficient mercury removal

Mercury (Hg) emissions are increasing annually owing to rapid global industrialization. Hg poisoning can severely affect the human body owing to its persistence and bioaccumulation. In this study, hybrid nanoflowers (NFs) were synthesized by promoting the formation of primary copper-phosphate crystals coordinated with polydopamine (PDA) and Fe₃O₄ magnetic nanoparticles (MNPs), followed by coating with silver nanoparticles on the surface of the NFs (Ag-MNP-PDA-Cu NFs). The results suggest that the hierarchical structure of the NFs enabled a large surface area with nanosized pores, which were exploited for Hg adsorption. The adsorbed Hg ions could be further eliminated from the solution based on the magnetic characteristics of the NFs. Additionally, hybrid NFs functionalized with Hg²⁺-binding aptamers (Apt-Ag-MNP-PDA-Cu NFs) were prepared based on the silver-sulfur interactions between the Ag-MNP-PDA-Cu NFs and thiol-modified aptamers. The performance of both adsorbents demonstrated that the immobilization of Hg²⁺-binding aptamers significantly improved the elimination of Hg from solution. The Hg²⁺ adsorption isotherm of the Apt-Ag-MNP-PDA-Cu NFs followed the Dubinin-Radushkevich model, with a maximum adsorption capacity of 1073.19 mg/g. The Apt-Ag-MNP-PDA-Cu NFs adsorbed greater amounts of Hg²⁺ than the non-functionalized NFs at the same concentrations, which confirmed that the functionalization of Hg²⁺-binding aptamers on the NFs improved the Hg²⁺ removal performance. The results suggest that Apt-Ag-MNP-PDA-Cu NFs could serve as an efficient Hg-removing adsorbent, possibly by providing binding sites for the formation of T-Hg²⁺-T complexes.

Adsorption of sulfur into an alkynyl-based covalent organic framework for mercury removal

A simple mercury removal strategy was developed that used a stable alkyl based covalent organic framework to adsorb sulfur first and then served as an adsorbent to remove Hg(ii) effectively.

Remarkable adsorption of hydroquinone as an anion contaminant by using the magnetic supported bimetallic (NiCu-MOF@MAC) nanocomposites in aqueous solutions

The purposes of this work were to synthesize the core-shell magnetic and nonmagnetic supported bimetallic metal-organic frameworks (MOFs) on the walnut-based activated carbon by the facile preparation method to investigate the feasibility of the performance adsorption of hydroquinone in the aqueous solutions. Activated carbon as a substrate and nickel, copper, and trimesic acid were employed in the structure of the prepared MOFs. The adsorbents were characterized by XRD, FTIR, FESEM, EDX, TEM, BET, and VSM analysis. The goethite and magnetite phases were detected in the morphology of the magnetic adsorbent as confirmed by the XRD pattern. Increases in the pH value from 6 and the adsorption temperature led to a lower adsorption capacity of the samples. The maximum adsorption capacity for the well-dispersed nanoparticles of magnetic (NiCu-MOF@MAC and nonmagnetic (NiCu-MOF@AC) was calculated to be 303.03 and 454.54 mg/g by using linear Langmuir isotherm as an appropriate model, respectively. The achievements from the reusability evaluation illustrated that the magnetic bimetallic MOF nanocomposite could successfully be applied to remove hydroquinone from the wastewater on an industrial scale. The kinetic experimental data was in good agreement with the pseudo-second-order model.

Biosorption of cationic Hg2+ and Remazol brilliant blue anionic dye from binary solution using Gelidium corneum biomass

Remazol brilliant blue (RBB) is an anthraquinone anionic dye that has several commercial uses, especially in the textile industries and is well-known for its detrimental impacts on marine life and the surrounding ecosystem. Mercury (Hg²⁺) is also one of the most severe hazardous environmental contaminants due to its bioaccumulation through the food chain and high toxicity to the human embryo and fetus. The biosorption potential of Gelidium corneum biomass for bioremoval of Hg²⁺ and RBB dye simultaneously from binary mixture was assessed. The effects of initial pH, contact time, Hg²⁺, RBB, and biomass concentrations on the biosorption process were investigated in 50 batch experiments using a Face-centered central composite design. The maximum removal percentage of Hg²⁺ (98.25%) was achieved in the run no. 14, under optimum experimental conditions: 200 mg/L Hg²⁺, 75 mg/L RBB, pH 5. At 30 °C, 4 g/L algal biomass was used, with a contact time of 180 min. Whereas, the maximum removal percentage of RBB (89.18%) was obtained in the run no. 49 using 200 mg/L Hg²⁺, 100 mg/L RBB, pH 5, 4 g/L algal biomass and 180 min of contact time. FTIR analysis of Gelidium corneum biomass surface demonstrated the presence of many functional groups that are important binding sites responsible for Hg²⁺ and RBB biosorption. SEM analysis showed apparent morphological alterations including surface shrinkage and the appearance of new shiny adsorbate ion particles on the Gelidium corneum biomass surface after the biosorption process. The EDX study reveals an additional optical absorption peak for Hg²⁺, confirming the role of Gelidium corneum biomass in Hg²⁺ biosorption. In conclusion, Gelidium corneum biomass has been shown to be an eco-friendly, sustainable, promising, cost-effective and biodegradable biosorbent to simultaneously biosorb Hg²⁺ and RBB dye from aquatic ecosystems.

The development of biomass-derived carbon-based photocatalysts for the visible-light-driven photodegradation of pollutants: a comprehensive review

Biomass-derived carbonaceous materials have recently attracted extensive interest on account of their exceptional physicochemical properties which make them promising candidates for various critical applications. Several achieved advances have been reported in the recent literature, mainly focusing on the areas of energy storage and conversion. There is no review dedicated specifically to the potential applications of biomass-derived carbon-based photocatalytic materials for environmental remediation using the visible spectral region. The excellent characteristics of carbon materials, such as good electronic conductivity, unique nanocrystal structures, inherent hydrophobicity, and the tunable surface characteristics, are fully compatible with diverse catalytic reactions including organic transformations and photocatalysis processes. Importantly, biomass-carbon-based materials are considered to be green and viable alternative photocatalysts due to their environmentally friendly and naturally abundant nature. This work aims to provide a comprehensive review of recent advances relating to the synthesis of biomass-derived carbon-based photocatalysts, focusing on their potential for the photodegradation of various pollutants. First, potential natural biomass sources, various synthetic routes, and the properties of carbon materials are systematically discussed. Recent advances in the production of biomass-carbon-based photocatalysts (including material design, mechanisms, and photocatalytic performance) are highlighted. Regarding ideas for the development of new biomass-derived photocatalysts, we outline research gaps that are worthy of further research in the future.

This review highlights recent advances relating to the synthesis of biomass-derived carbon-based photocatalysts in light of their potential use in the photodegradation of various pollutants.

Sulfur-anchored palm shell waste-based activated carbon for ultrahigh sorption of Hg(II) for in-situ groundwater treatment

This study utilized a facile and scalable one-pot wet impregnation method for Hg(II) adsorption to prepare sulfur-anchored palm shell waste activated carbon powder (PSAC-S). The experimental results revealed that the sulfur precursors promote the surface charge on the PSAC and enhance Hg(II) removal via the Na₂S > Na₂S₂O₄ > CH₃CSNH₂ sequence. PSAC-S prepared using Na₂S had significant Hg(II) sorption efficiencies, achieving a maximum sorption capacity of 136 mg g^-1 from the Freundlich model. Compared to PSAC, PSAC-S had an enhancement in Hg(II) sorption behavior for heterogeneous interactions with sulfur. PSAC-S also demonstrated high Hg(II) sorption capacities over a wide range of solution pH, while ionic strength had an insignificant impact on Hg(II) removal efficiencies. Through various spectroscopic analyses, we identified the mechanisms of Hg(II) removal by PSAC-S as electrostatic interactions, Hg-Cl complexation, and precipitation as HgSO₄. Moreover, PSAC-S unveiled high adsorption affinity and Hg(II) stability in actual groundwater (even in µg L^-1 level). These overall results show the potentials of PSAC-S as an alternative, easily scalable material for in-situ Hg(II) remediation.

An Overview on Total Valorization of Litsea cubeba as a New Woody Oil Plant Resource toward a Zero-Waste Biorefinery

With the increasing global demand for edible oils and the restriction of arable land minimum in China, woody oil plants have gradually become the optimal solution to cover the shortage of current edible oil supply and to further improve the self-sufficiency rate. However, due to the lack of knowledge and technique, problems like “how to make full use of these plant resources?” and “how to guide consumers with reasonable data?” limit the development of woody oilseed industry towards a sustainable circular economy. In this review, several emerging unique woody oil plants in China were introduced, among which Litsea cubeba as a new woody oil plant was highlighted as a reference case based on its current research progress. Unlike other woody oil plants, essential oil rather than oil from Litsea cubeba has always been the main product through the years due to its interesting biological activities. Most importantly, its major component, citral, could be the base for other synthesized perfume compounds with added value. Moreover, the sustainable biorefinery of large amounts of waste residual after Litsea cubeba essential oil processing is now technically feasible, which could inspire a total valorization pathway for other woody oil plants to make more competitive plant-based products with both economic, social, and ecological benefits.

Synthesis of the magnetic core-shell bi-metallic and tri-metallic metal-organic framework nanocomposites for dye adsorption

Bi-metallic and tri-metallic metal-organic frameworks (MOFs) supported on the magnetic activated carbon (MAC) were synthesized for the reduction of methylene blue (MB) concentration in the aqueous solutions. The adsorbent nanocomposites were characterized by applying the general tests including XRD, FTIR, FESEM, TEM, BET, and VSM. The XRD achievements demonstrated that crystalline structure of MOFs was derived on the MAC by the presented method. The core-shell morphology with nano-scale size of the magnetic carbonaceous MOFs was detected in TEM and FESEM micro-images. The acceptable magnetic strength of the prepared adsorbents was proved by using the VSM analysis. The important operating conditions including pH and temperature were also evaluated, while the other parameters were kept constant. The pseudo-second-order kinetic model was matched with the experimental data to show the kinetic behavior of the multi-component MOFs. The isotherm studies showed that the good agreement between the experimental data with both Langmuir model and the maximum capacities was calculated to be about 66.51 and 71.43 mg/g for the bi-metallic and tri-metallic nanocomposites, respectively. Regeneration experiments indicated that the fabricated adsorbents have an excellent reusing adsorption capacity which can be a proper selection for the industrial applications. PRACTITIONER POINTS: Bi-metallic and tri-metallic MOFs supported on the magnetic activated carbon were synthesized by the facile preparation method. Adsorption of methylene blue by using MOFs were successfully done. Nanocomposites were evaluated by XRD, FTIR, BET, FESEM, TEM, and VSM techniques. Maximum of adsorption capacity was observed for tri-metallic MOF as 71.43 mg/g.

P-nitrophenol degradation by pine-wood derived biochar: The role of redox-active moieties and pore structures

Biochar can both adsorb and degrade p-nitrophenol (PNP); however, the PNP degradation mechanism has not been well investigated. We prepared two biochars at pyrolysis temperatures of 500 °C (B500) and 700 °C (B700). Although B500 showed much stronger free radical signals (which are associated with organic degradation, according to previous studies), the apparent PNP degradation was approximately 3 times higher in the B700 system. The degradation increased significantly after the biochars were washed with water. According to a quantitative analysis of the sorption and degradation and two-compartment first-order kinetics modeling of the apparent removal kinetics, sorption occurred mainly in the initial period, whereas degradation continued throughout the removal process. The PNP degradation rate constant depended mainly on the external surface area at a relatively low concentration (200 mg/L) and was controlled by the microporous surface area at a relatively high concentration (800 mg/L). In addition, the apparent degradation did not depend on the biochar particle size. Therefore, PNP degradation may be related to the three-dimensional structure of the biochar in addition to the exposed external surface. The well-developed pore structure, more accessible surface, and larger electron exchange capacity of B700 may promote electron transfer between the biochar and PNP, and thus accelerate PNP degradation. This study demonstrates that various properties of the biochar may contribute to PNP degradation.

Immobilization of Hg(II) on high-salinity Spirulina residue-induced biochar from aqueous solutions: Sorption and transformation mechanisms by the dual-mode isotherms

Removal of Hg(II) by biochar (BC) is a promising remediation technology. The high-salinity Spirulina residue (HSR) is a hazardous waste generated during extracting the pigment phycocyanin under high salinity conditions. Although HSR-derived BC (HSRBC) exhibited the excellent sorption capacity of Hg(II), the involved mechanisms have been rarely studied. In this study, we investigated the specific properties and Hg(II) sorption mechanisms of HSRBCs. Chloride and calcium minerals were formed in HSRBCs. Increments in carbonization temperature (from 350 to 700 °C) or time (from 90 to 540 min) led to the enhancement of aromaticity, porosity, and positive charge, but cracked oxygen-containing groups and C-N bonds. Further increase in carbonization temperature or time decreased the sorption of Hg(II). At environmentally relevant concentration of Hg(II) (2-4 mg/L), the sorption capacity (6.1-12.7 mg/g) obtained in HSRBC350 was comparable to activated carbon. Based on dual-mode isotherm, surface sorption accounted for 75-88% uptake, while precipitation accounted for 12-25% uptake. In addition, the C-O, CO, and CC groups were responsible for the monodentate/bidentate complexation and reduction, while Cl^- triggered Hg₂Cl₂ precipitation. Overall, this study provided a new insight in creating an excellent Hg(II) sorbent from hazardous waste, and revealed the sorption mechanisms for Hg(II) uptake.

Mechanistic investigation of mercury removal by unmodified and Fe-modified biochars based on synchrotron-based methods

Improved surface characteristics and incorporated Fe, S, and Cl species are reported in Fe-modified biochar, which makes it a prospective material for Hg(II) removal. In this study, aqueous Hg(II) was removed from solution by unmodified, FeCl₃-modified, and FeSO₄-modified biochars pyrolyzed at 300, 600, or 900 °C. Higher pyrolytic temperature resulted in higher removal efficiency, with the biochars pyrolyzed at 900 °C removing >96% of Hg(II). Fe-modification enhanced Hg(II) removal for biochars pyrolyzed at 600 °C (from 88% to >95%) or 900 °C (from 96% to 99%). Based on synchronous extended X-ray absorption fine structure (EXAFS) analysis, Hg coordinated to S in modified and unmodified biochars pyrolyzed at 900 °C, where thiol was reported, and in FeSO₄-modified biochars pyrolyzed at 600 or 900 °C, where sulfide was recognized; in other biochars, Hg bound to O or Cl. Additionally, confocal micro-X-ray fluorescence imaging (CMXRFI) demonstrated Hg was distributed in agreement with S in biochars where HgS was formed; otherwise, Hg distribution was influenced by Hg species in solution and the pore characteristics of the biochar. This investigation provides information on the effectiveness and mechanisms of Hg removal that is critical for evaluating biochar applications and optimizing modification methods in groundwater remediation.

Adsorption of aqueous Hg2+ and inhibition of Hg0 re-emission from actual seawater flue gas desulfurization wastewater by using sulfurized activated carbon and NaClO

The potential impacts of seawater flue gas desulfurization (SFGD) process used in coal-fired power plants have been greatly concerned because the wastewater containing Hg is directly discharged into the ocean environment without proper treatment. Furthermore, the re-emission of Hg as Hg⁰ to the atmosphere from SFGD wastewater caused by the reduction of aqueous Hg²⁺ has also been observed. This study investigated the dependence of Hg²⁺ adsorption behavior for sulfurized activated carbon (SAC) in actual SFGD wastewater on various influencing factors, including initial Hg²⁺ concentration, solution pH, contact time, temperature, and the addition of oxidant (sodium hypochlorite, NaClO). SAC exhibited greater Hg²⁺ adsorption than raw activated carbon at an initial Hg²⁺ concentration of more than 4,723 ng L^-1. The Hg²⁺ removal efficiency of SAC was slightly larger at pH 7.0 and 8.0 than that at pH within 2.0-6.0. Hg²⁺ adsorption on SAC was well correlated with the linear adsorption model. Kinetic analysis results indicate that pseudo-second-order adsorption may serve as the rate-limiting reaction of Hg²⁺ adsorption on SAC. Thermodynamic analyses confirmed the endothermic and spontaneous adsorption behavior of Hg²⁺ on SAC in the seawater environment. Notably, the addition of NaClO significantly reduced the Hg²⁺ removal efficiency when SAC was used as the adsorbent. Nevertheless, NaClO addition also inhibited the reduction reaction of Hg²⁺ to Hg⁰ by forming strong HgCl complexes, which decreased the risk of Hg⁰ reemitted into the atmosphere via a SFGD system.

Recent Advances in Applications of Hybrid Graphene Materials for Metals Removal from Wastewater

The presence of traces of heavy metals in wastewater causes adverse health effects on humans and the ecosystem. Adsorption is a low cost and eco-friendly method for the removal of low concentrations of heavy metals from wastewater streams. Over the past several years, graphene-based materials have been researched as exceptional adsorbents. In this review, the applications of graphene oxide (GO), reduce graphene oxide (rGO), and graphene-based nanocomposites (GNCs) for the removal of various metals are analyzed. Firstly, the common synthesis routes for GO, rGO, and GNCs are discussed. Secondly, the available literature on the adsorption of heavy metals including arsenic, lead, cadmium, nickel, mercury, chromium and copper using graphene-based materials are reviewed and analyzed. The adsorption isotherms, kinetics, capacity, and removal efficiency for each metal on different graphene materials, as well as the effects of the synthesis method and the adsorption process conditions on the recyclability of the graphene materials, are discussed. Finally, future perspectives and trends in the field are also highlighted.

Recent advances in the use of walnut (Juglans regia L.) shell as a valuable plant-based bio-sorbent for the removal of hazardous materials

The effective use of agricultural by-products is definitely a major challenge in waste management. In the walnut fruit processing industry, large amounts of shells are produced as agricultural by-products and discarded or burned produced as fuel. Walnut (Juglans regia L.) is a valuable tree nut in the Juglandaceae family. The fruit is composed of four main parts: the kernel, the skin, the shell, and the husk. The importance of walnuts is mostly related to theirs valuable kernels. However, their shells are currently experiencing as much interest as their kernels due to the beneficial effects of the shells. In the past several years, walnut shell (WS) has been widely explored as a naturally inert plant-based biosorbent. In this review, we first highlight recent scientific literature regarding the development of adsorbents from WS in the form of carbon-based materials including unmodified/modified WS, and activated carbons (ACs). Next, we discuss the potential applications of WS-derived by-products as natural yet effective adsorbents for the removal of various hazardous materials including heavy metals (HMs), synthetic industrial dyes, and harmful chemicals.

The effective use of agricultural by-products is definitely a major challenge in waste management.

Mercury Removal from Aqueous Solutions Using Modified Pyrite: A Column Experiment

Modified pyrite (MPy), which was obtained from calcination in an N2 atmosphere, was used as a sorbent for removing Hg(II) from aqueous solutions. Fixed-bed column experiments were conducted to determine the Hg(II) removal ability of MPy from aqueous solutions. MPy was found to be much better than natural pyrite for mercury removal. The concentration of Hg(II) in effluents was much lower than that of the emission standard used for Hg wastewater in China (0.05 mg/L), and the removal efficiency of Hg(II) was greater than 99% before breakthrough. When the capacity was 3274 times the column bed volume (1 bed volume = 25.12 cm3), the column breakthrough and the sorption amount of Hg(II) were 54.44 mg/g. The Hg(II) content in the used MPy sorbent was up to 24.79%. The mechanism was analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), field emission transmission electron microscopy (FE-TEM), and X-ray Photoelectron Spectroscopy (XPS). The main mechanism of Hg(II) removal by MPy was the chemical reactions between mercury ions and mineral fillers, and HgS precipitated on the surface of MPy to remove Hg(II). The reaction was also accompanied by surface complexation and adsorption. The results of this work show that MPy can be used as a sorbent for continuous Hg(II) removal.

Characterization and Modelling Studies of Activated Carbon Produced from Rubber-Seed Shell Using KOH for CO2 Adsorption

Global warming due to the emission of carbon dioxide (CO2) has become a serious problem in recent times. Although diverse methods have been offered, adsorption using activated carbon (AC) from agriculture waste is regarded to be the most applicable one due to numerous advantages. In this paper, the preparation of AC from rubber-seed shell (RSS), an agriculture residue through chemical activation using potassium hydroxide (KOH), was investigated. The prepared AC was characterized by nitrogen adsorption–desorption isotherms measured in Micrometrices ASAP 2020 and FESEM. The optimal activation conditions were found at an impregnation ratio of 1:2 and carbonized at a temperature of 700 °C for 120 min. Sample A6 is found to yield the largest surface area of 1129.68 m2/g with a mesoporous pore diameter of 3.46 nm, respectively. Using the static volumetric technique evaluated at 25 °C and 1.25 bar, the maximum CO2 adsorption capacity is 43.509 cm3/g. The experimental data were analyzed using several isotherm and kinetic models. Owing to the closeness of regression coefficient (R2) to unity, the Freundlich isotherm and pseudo-second kinetic model provide the best fit to the experimental data suggesting that the RSS AC prepared is an attractive source for CO2 adsorption applications.

Artificial Neural Network Approach for Modelling of Mercury Ions Removal from Water Using Functionalized CNTs with Deep Eutectic Solvent

Multi-walled carbon nanotubes (CNTs) functionalized with a deep eutectic solvent (DES) were utilized to remove mercury ions from water. An artificial neural network (ANN) technique was used for modelling the functionalized CNTs adsorption capacity. The amount of adsorbent dosage, contact time, mercury ions concentration and pH were varied, and the effect of parameters on the functionalized CNT adsorption capacity is observed. The (NARX) network, (FFNN) network and layer recurrent (LR) neural network were used. The model performance was compared using different indicators, including the root mean square error (RMSE), relative root mean square error (RRMSE), mean absolute percentage error (MAPE), mean square error (MSE), correlation coefficient (R²) and relative error (RE). Three kinetic models were applied to the experimental and predicted data; the pseudo second-order model was the best at describing the data. The maximum RE, R² and MSE were 9.79%, 0.9701 and 1.15 × 10^-3, respectively, for the NARX model; 15.02%, 0.9304 and 2.2 × 10^-3 for the LR model; and 16.4%, 0.9313 and 2.27 × 10^-3 for the FFNN model. The NARX model accurately predicted the adsorption capacity with better performance than the FFNN and LR models.

Superior removal of Hg (II) ions from wastewater using hierarchically porous, functionalized carbon

The removal of heavy metal ions from industrial wastewater by adsorption has been central to the environment for decades, where common adsorbent materials are often limited by poor efficiency, complex fabrication and long processing time. Porous carbon derived from biospecies holds promise to address the limitations. In this study we converted bagasse into a carbon composite having hierarchically porous structure; the composite's dispersion phases - iron oxide and manganese oxide - were synthesized by a simple one-step liquid-phase reaction method. Featuring large specific surface area of 350.8 m² g^-1, the composite demonstrated exceptional Hg (II) removal efficiency of 96.8%, adsorption rate of up to 96.8% within 150 min and adsorption capacity of 9.8 mg g^-1. In comparison with other removal materials, our work is outstanding in terms of both removal efficiency and synthesis simplicity. The high efficiency is attributed to the synergy between physical adsorption referring to hierarchically porous structure and chemical adsorption relating to functional complexation processes. It provides a new avenue for the development of high-performance adsorbent materials for heavy metal removal from aqueous media.

Selective removal behavior and mechanism of trace Hg(II) using modified corn husk leaves

Removal of Hg(II) from wastewater was beneficial to satisfy the discharge standards of China's mercury-containing wastewater (50 ppb). An adsorbent was prepared via modifying corn husk leaves with bismuthiol I. The results revealed that the mercury removal rate was more than 98.5% at pH 1.0-7.0. Moreover, the removal rate reached 96% at 5 min and the residual concentration decreased from 10 ppm to approximately 30 ppb. In addition, the adsorbent owned a conspicuous selective absorbability for trace Hg(II) from wastewater. The adsorption process followed a Hill isotherm model. The actual saturated adsorption quantity of the adsorbent was 707 mg/g. The repeatability experiment indicated that the mercury removal efficiency was still beyond 99% after three cycles. The X-ray photoelectron spectroscopy suggested that the main adsorption mechanism was chelation between nitrogen/sulfur groups and Hg(II). The adsorbent was hopeful to remove mercury from wastewater in a sustainability perspective.

Molecular Imprinted Based Quartz Crystal Microbalance Nanosensors for Mercury Detection

Mercury(II) ions are emerging as a result of more human activity, especially coal-fired power plants, industrial processes, waste incineration plants, and mining. The mercury found in different forms after spreading around diffuses the nature of other living things. Although the damage to health is not yet clear, it is obvious that it is the cause of many diseases. This work detects the problem of mercury(II) ions, one of the active pollutants in wastewater. For this purpose, it is possible to detect the smallest amount of mercury(II) ions by means of the mercury(II) ions suppressed quartz crystal microbalance nanosensor developed. Zinc(II) and cadmium(II) ions are chosen as competitor elements. Developed nanosensor technology is known as the ideal method in the laboratory environment to detect mercury(II) ions from wastewater because of its low cost and precise result orientation. The range of linearity and the limit of detection are measured as 0.25 × 10-9-50 × 10-9 m. The detection limit is found to be 0.21 × 10-9 m. The mercury(II) ions imprinted nanosensors prepared according to the obtained experimental findings show high selectivity and sensitivity to detect mercury(II) ions from wastewater.

Removal of Hg(ii) in aqueous solutions through physical and chemical adsorption principles

Adsorption has been the focus of research on the treatment of heavy metal mercury pollution since it is among the most toxic heavy metals in existence.

Fabrication of NiFe2O4 magnetic nanoparticles loaded on activated carbon as novel nanoadsorbent for Direct Red 31 and Direct Blue 78 adsorption

In this research, magnetic nickel ferrite NiFe₂O₄/hazelnut-shell-based activated carbon (NiFe₂O₄/AC) was used to eliminate anionic dyes (Direct Red 31(DR31) and Direct Blue 78 (DB78)) from aqueous solution. The morphological, structural, particle size and surface charge properties of as-prepared nanoadsorbent were characterized. TEM (Transmission electron microscopy) images revealed that the size of NiFe₂O₄ particles in the structure of AC was in the range of 8-12 nm, which is compatible with the results obtained by the analysis of DLS (Dynamic light scattering). The results of the BET (Brunauer-Emmett-Teller) analysis indicated that the surface area, the pore volume and average pore diameters of the NiFe₂O₄ were 288 m²/g, 0.3338 cm³/g and 5.05nm, respectively. The as-prepared nanocomposite showed excellent adsorption capacity for DR31 and DB78 dyes with the highest adsorption capacity obtained at pH=2.0 and rapid dye adsorption equilibrium attained after 20 and 25 min for DR31 and DB78, respectively. The equilibrium study showed the maximum adsorption capacity (q_max) of 299.67 mg/g and 209.13 mg/g for DR31 and DB78, respectively. In addition, thermodynamic study revealed the endothermic and spontaneous nature of adsorption process. The adsorption of DR31 and DB78 onto the NiFe₂O₄/AC is a physisorption process, during which electrostatic adsorption was the main driving force.

Removal of nitrobenzene from aqueous solution by adsorption onto carbonized sugarcane bagasse

A sorbent was prepared by charring sugarcane bagasse (SCB) and used to remove nitrobenzene from aqueous solution. The surface area, morphology, and functional groups of the adsorbent were characterized by Brunauer–Emmett–Teller method, scanning electron microscopy, and Fourier transforms infrared spectroscopy. Analysis indicated that oxygen-containing functional groups, such as C = O, –OH, –COOH, and C–O–C, may be involved in the adsorption process. The adsorption of nitrobenzene was investigated under different operating conditions, including adsorbent dosage, initial nitrobenzene concentration, pH, and contact duration. Four kinetic models were applied to describe the adsorption process. Results revealed that the optimal sorbent mass was 0.3 g/50 mL at pH 5.8 and 25°C. The kinetic data obeyed the pseudo-second-order kinetic model ( R2 > 0.9965). In addition, Langmuir and Freundlich isotherm models were employed to describe the adsorption equilibrium. The Freundlich model presented better fitting for the adsorption equilibrium, suggesting that the carbonized SCB surface had a heterogeneous nature. The maximum adsorption capacities calculated by the Langmuir model were 38.27, 41.72, and 44.70 mg/g at 25°C, 35°C, and 45°C, respectively. The calculated values of ΔG0 and ΔH0 indicated the spontaneous and exothermic nature of the adsorption process at the considered temperature range. The adsorption mechanism of nitrobenzene onto carbonized SCB cannot be described either as physical adsorption or chemisorption. This study demonstrated that SCB biochar is a potential sorbent for removing nitrobenzene from aqueous solutions.

Comparative biosorption study of Hg (II) using raw and chemically activated almond shell

This work presents a comparison between the biosorption of Hg (II) by raw almond shell and activated almond shell. Almond shell based activated carbon has been obtained by physicochemical activation. Batch biosorption results confirmed that, activating condition has a strong influence on the final biosorption process. The biosorbent was characterized using scanning electron microscopy and Fourier transform infrared spectroscopy. To optimize the biosorption conditions pH, adsorbent dose, initial concentration, contact time, stirring speed, and temperature on Hg (II) removal were studied. The optimum conditions for maximum Hg (II) was achieved at 20 and 10 min for raw almond shell and activated almond shell, respectively. The equilibrium data were described well by Langmuir, Freundlich, Dubinin–Radushkevich isotherm models and appling a test of model fitness. Best fit of Langmuir and Freundlich models were found for experimental data, which reveal the homogenous surface of raw almond shell and the heterogeneity of activated almond shell surface. The kinetic data had been divided into either pseudo first order or second order on the basis of the best fit obtained from calculations, confirmed by a test of kinetic validity. An industrial application was examined to improve high biosorption capacity of raw and activated almond shells toward Hg (II).

Adsorption-assisted decontamination of Hg(ii) from aqueous solution by multi-functionalized corncob-derived biochar

Mercury (Hg) contamination of wastewater streams as a result of anthropogenic activities is a great threat to living organisms due to its acute toxicity.

Walnut (Juglans regiaL.) shell pyroligneous acid: chemical constituents and functional applications

Upon the processing of different agricultural products, considerable amounts of by-products and bio-wastes are produced and discarded or burnt as fuel, which are a potential source of valuable compounds. Over the past several decades, plant by-products have been recognized as a source of nutraceutical components, including dietary fibers, phenolics, and many other useful compounds. The walnut is known as an important tree nut. The shell of a walnut is the middle part of the fruit and it is a waste product of walnut processing industries. Recently, pyroligneous acids from the walnut shell have been receiving much-increasing interest because of their excellent antimicrobial and antioxidant activities. Hence, this review deals with the recent scientific literature on walnut shell pyroligneous acids and their chemical composition as well as their functional applications.

Upon the processing of different agricultural products, considerable amounts of by-products and bio-wastes are produced and discarded or burnt as fuel, which are a potential source of valuable compounds.

Study of the adsorption of mercury (II) on lignocellulosic materials under static and dynamic conditions

WHO has declared mercury as one of the most dangerous pollutants for human health. Unfortunately, several cases of rivers and aquifers contaminated by mercury inevitably poses the problem on how to remediate them. Considerable efforts are being addressed to develop cost-effective methodologies, among which the use of low-cost adsorbing materials. In this paper, the adsorption performances of an alternative lignocellulosic material derived from the Spanish broom plant, are presented. This plant is widely diffused in the world and its usage for Hg(II) removal from water in real working conditions requires only minimal pretreatment steps. A thoroughly investigation on the kinetics and thermodynamics of Hg(II) adsorption on Spanish broom is presented, by using Hg(II) polluted aqueous solutions specifically prepared in order to simulate typical groundwater conditions. Several batch experiments, under static conditions, were carried out in order to evaluate the effect of pH, contact time, adsorbent dosage, initial concentration, temperature. A maximum adsorption capacity of 20 mg L^-1 can be obtained at pH 5, following a pseudo second order kinetics. Moreover, adsorption experiments in dynamic conditions were carried out using Spanish broom filters. Interestingly, a systematic, unconventional double S-shape breakthrough curve was observed under different experimental conditions, revealing the occurrence of two adsorption processes with different time scales. This behavior has been fitted by a bimodal Thomas model which, unlike the single Thomas fitting, gives satisfactory results with the introduction of a new parameter related to the fraction of surface active sites involved in the adsorption processes.

Characterizing Biochar as Alternative Sorbent for Oil Spill Remediation

Biochar (BC) was characterized as a new carbonaceous material for the adsorption of toluene from water. The tested BC was produced from pine wood gasification, and its sorption ability was compared with that of more common carbonaceous materials such as activated carbon (AC). Both materials were characterized in terms of textural features and sorption abilities by kinetic and equilibrium tests. AC and BC showed high toluene removal from water. Kinetic tests demonstrated that BC is characterized by faster toluene removal than AC is. Textural features demonstrated that the porosity of AC is double that of BC. Nevertheless, equilibrium tests demonstrated that the sorption ability of BC is comparable with that of AC, so the materials’ porosity is not the only parameter that drives toluene adsorption. The specific adsorption ability (mg sorbed m⁻² of surface) of the BC is higher than that of AC: toluene is more highly sorbed onto the biochar surface. Biochar is furthermore obtained from biomaterial thermally treated for making energy; this also makes the use of BC economically and environmentally convenient compared with AC, which, as a manufactured material, must be obtained in selected conditions for this type of application.