Two-compartment membrane electrochemical remediation of heavy metals from an aged electroplating-contaminated soil: A comparative study of anodic and cathodic processes

Regulating pH distribution of soda saline-alkali soil during electrochemical treatment by conditioning catholyte pH coupled with approaching anodes

Soda saline-alkali soils pose significant challenges to agricultural productivity due to high pH and excessive sodium content. This study investigated the removal of excess salts in soda saline-alkali soil through electrochemical treatment (ECT). Traditional ECT often led to uneven soil pH distribution, with acidic conditions near the anode and alkaline conditions near the cathode, which limited its effectiveness for soil improvement. We explored the impact of conditioning the catholyte pH coupled with approaching anode electrochemical treatment (AA-ECT) on soil pH distribution and the removal of soluble sodium ions in soda saline-alkali soil. The results demonstrated that AA-ECT was less effective than fixed anode electrochemical treatment (FA-ECT) in regulating soil pH, achieving a relatively uniform pH range of 7.31-8.44. Adding acetic acid further improved pH uniformity, narrowing the range to 7.32-8.02. Moreover, all experimental groups exhibited high removal of soluble sodium ions efficiency, and the acetic acid coupled with AA-ECT achieved an average removal efficiency of 91.90%. Notably, the soil was successfully transformed from severely alkali soil (exchangeable sodium percentage (ESP) > 61%) to non-alkali soil (ESP < 14%). Additionally, the AA-ECT groups showed lower energy consumption than the FA-ECT groups. These findings highlighted that conditioning the catholyte pH coupled with AA-ECT was a highly effective strategy for improving soda saline-alkali soils, offering a sustainable solution for soil remediation and agricultural productivity enhancement.

Enhanced electrokinetic remediation by magnetic induction for the treatment of co-contaminated soil

The electroplating industry site is an important reservoir of per- and poly-fluoroalkyl substances (PFASs) and heavy metals. In this work, a novel electrokinetic in-situ chemical oxidation system was established to restore an actual soil co-contaminated with high concentrations of heavy metals (Cr, Cu, Zn and Ni) and PFASs. Potassium persulfate (PS, K₂S₂O₈) and industrial waste steel slag were used as the oxidant and activator, respectively. The steel slag was evenly added in the soil, while PS was dosed in the cathode chamber. Citric acid fermentation broth produced by Aspergillus niger was added in the anode chamber to act as the metal chelator. A periodic alternating magnetic field was employed to enhance the catalytic performance of steel slag for PS. After 15-day treatment, 86.7% of PFASs and 87.2% of heavy metals were removed without PFASs accumulation in the electrolyte, with a defluorination percentage of 79.2%. The remediated soil had no phytotoxicity for wheat seed growth based on 7-day cultivation results. The quality of remediated soil could reach the national Class II criteria for residential use. Electron paramagnetic resonance spectroscopy analysis demonstrated that SO₄^•- and ^•OH were the major oxidative radicals responsible for PFASs degradation. Adding steel slag in the soil performed better than that in the cathode chamber based on pollutant removal and alleviating soil acidification. Magnetic induction could enhance PS activation by promote the corrosion of steel slag and thermal activation, thus increasing electrical current and electroosmotic flow, enhancing the transport of citric acid and PS, significantly improving the removal efficiency of heavy metals and PFASs.

Green remediation of Ni, Zn, and Cu in an electroplating contaminated site by wood vinegar with optimization and risk assessment

Wood vinegar (WV) is a renewable organic compound, possessing characteristics such as high oxygenated compound content and low negative impact on soil. Based on its weak acid properties and complexing ability to potentially toxic elements (PTEs), WV was used to leach Ni, Zn, and Cu contaminated soil in electroplating sites. In addition, the response surface methodology (RSM) based on the Box-Behnken design (BBD) was established to clarify the interaction between each single factor, and finally completed the risk assessment of the soil. The amounts of PTEs leached from the soil climbed with the increase of WV concentration, liquid-solid ratio, and leaching time, while they surged with the decrease of pH. Under optimal leaching circumstances (the concentration of WV= 100 %; washing time= 919 min; pH= 1.00), the removal rates of Ni, Zn, and Cu could reach 91.7 %, 57.8 %, and 65.0 %, respectively, and the WV-extracted PTEs were mainly from the Fe-Mn oxides fraction. After leaching, the Nemerow integrated pollution index (NIPI) decreased from an initial value of 7.08 (indicating severe pollution) to 0.450 (indicating no pollution). The potential ecological risk index (RI) dropped from 274 (medium level) to 39.1 (low level). Additionally, the potential carcinogenic risk (CR) values reduced by 93.9 % for both adults and children. The results revealed that the washing process significantly reduced the pollution level, potential ecological risk, and health risk. Coupled with FTIR and SEM-EDS analysis, the mechanism of WV removal of PTEs could be explained from three aspects: acid activation, H⁺ ion exchange, and functional group complexation. In summary, WV is an eco-friendly and high-efficiency leaching material for the remediation of PTEs polluted sites, which will maintain soil function and protect human health.

Sustainable and reagent-free cathodic precipitation for high-efficiency removal of heavy metals from soil leachate

Heavy metal pollution of soils has become a serious environmental problem. Soil washing with degradable reagents is an effective remediation technique of heavy metal pollution, and the generated leachate must be appropriately treated before discharge. However, the existing methods usually have the problems of large consumption of regents, high cost, and secondary pollution. This study proposed a reagent-free electrochemical precipitation method to remove mixed heavy metal ions extracted from soils by citrate using inert electrodes (IrO₂-Ta₂O₅/Ti anode and graphite cathode). The results showed that the low potential of cathode led to the electrodeposition of Cd; the local alkaline environment provided by electro-mediated water reduction caused the hydrolytic precipitation of Zn and Pb; and the precipitation of Fe washed out from Fe-rich soil resulted in the coprecipitation of As on cathode surface. These combined cathodic precipitation processes decreased the concentrations of toxic heavy metals by over 99.4% after 12 h of electrolysis at 26 mA cm^-2. The electrodes exhibited high stability after multiple successive cycles of reuse. The concentrations of As, Zn, Pb and Cd in the leachate decreased to below the limits of industrial wastewater discharge in each cycle, and those in soils could be reduced by 53.8%, 58.8%, 25.5%, and 70.2% at the initial concentrations of 1549, 1016, 310 and 50 mg kg^-1, respectively. The heavy metal removal rate increased with increasing current density in the range of 0-52 mA cm^-2. This work provides an efficient and sustainable method for the remediation of site soils polluted by mixed heavy metals.

Effects of tannic acid on the transport behavior of trivalent chromium in soils and its mechanism

Trivalent chromium [Cr(III)] and tannins serve as necessary substances in leather processing and coexist in tannery site, which lead to the chromium contamination in site soil when disposed improperly. However, coexisting tannins are very likely to complex with Cr(III) and affect its properties, ultimately changing the mobility of chromium in soil. In this study, tannic acid (TA) was selected to investigate the complexation with Cr(III) and the influence on the solubility and sorption of Cr(III) in soils. Then, the transport behavior and mechanism of Cr(III)-TA complexes in soil was clarified. Dialysis results showed that the increase of TA concentration and solution pH promoted the formation of complexed Cr(III). The results of UV-Vis absorption spectroscopy, X-ray photoelectron spectroscopy, and density functional theory calculations indicated that the adjacent ionized phenolic hydroxyls in TA functioned as the binding sites with Cr(III) to form the Cr-O bonds and the degree of complexation increased with pH. The Cr(III)-TA complexes had higher solubility than free Cr(III) at pH ≥ 6.0. Batch sorption experiments demonstrated that the sorption capacity of Cr(III)-TA to soils with different pH was always lower than that of free Cr(III). These reasons led to the stronger mobility of Cr(III)-TA in soil columns than Cr(III). Our research reveals that the enhanced mobility of Cr(III) in soils coexisting with TA.

Removal behavior and mechanisms of cadmium and lead by coupled ethylenediaminetetraacetic acid washing and electrochemical reduction: influence of current conditions

Ethylenediaminetetraacetic acid (EDTA) washing has been used extensively to remediate heavy metal-contaminated soils. Electrochemical reduction treatment of spent washing solution is an effective method of EDTA regeneration. However, at present, these two technologies are usually regarded as two independent treatment processes. This research raised a new heavy metal-contaminated soil treatment strategy-a combination technique of coupled EDTA washing and electrochemical reduction. We speculated that the combination of EDTA washing and electroreduction treatment could improve the efficiency of Cd and Pb removal from contaminated soil. In this study, the removal performance and mechanisms of Cd and Pb under different current conditions were investigated based on a coupling of EDTA washing and electrochemical reduction. The combination technique can increase Cd and Pb removal efficiencies by 13.37-15.24% and 14.91-27.05%, respectively, compared with EDTA washing alone. Sequential extraction analysis showed that the reducible fraction improved metal removal efficiency. The percentage of metal removed increased with an increased current value and EDTA concentration. In addition, pulse current mode removed more Cd and Pb than continuous current, although the difference was not significant (p > 0.05). However, pulse current could effectively eliminate the cathodic hydrogen evolution reaction, resulting in a further heavy metal deposition at the cathode. The combination technique exhibited enhanced removal efficiency due to EDTA regeneration in the suspension and the cathodic reduction reaction. The most cost-effective treatment in 48 h was a pulse current mode of 32 min on/16 min off-32 mA-EDTA-10 mM, where 47.56% of Cd and 77.00% of Pb were removed from the soil with an electric energy consumption of 8.24 Wh.

Practical limitations of bioaugmentation in treating heavy metal contaminated soil and role of plant growth promoting bacteria in phytoremediation as a promising alternative approach

Bioaugmentation, the addition of cultured microorganisms to enhance the currently existing microbial community, is an option to remediate contaminated areas. Several studies reported the success of the bioaugmentation method in treating heavy metal contaminated soil, but concerns related to the applicability of this method in real-scale application were raised. A comprehensive analysis of the mechanisms of heavy metal treatment by microbes (especially bacteria) and the concerns related to the possible application in the real scale were juxtaposed to show the weakness of the claim. This review proposes the use of bioaugmentation-assisted phytoremediation in treating heavy metal contaminated soil. The performance of bioaugmentation-assisted phytoremediation in treating heavy metal contaminated soil as well as the mechanisms of removal and interactions between plants and microbes are also discussed in detail. Bioaugmentation-assisted phytoremediation shows greater efficiencies and performs complete metal removal from soil compared with only bioaugmentation. Research related to selection of hyperaccumulator species, potential microbial species, analysis of interaction mechanisms, and potential usage of treating plant biomass after treatment are suggested as future research directions to enhance this currently proposed topic.