Aerobic biodegradation in freshwater and marine environments of textile microfibers generated in clothes laundering: Effects of cellulose and polyester-based microfibers on the microbiome

Design of biodegradable cellulose filtration material with high efficiency and breathability

Using respiratory protective equipment is one of the relevant preventive measures for infectious diseases, including COVID-19, and for various occupational respiratory hazards. Because experienced discomfort may result in a decrease in the utilization of respirators, it is important to enhance the material properties to resolve suboptimal usage. We combined several technologies to produce a filtration material that met requirements set by a cross-disciplinary interview study on the usability of protective equipment. Improved breathability, environmental sustainability, and comfort of the material were achieved by electrospinning poly(ethylene oxide) (PEO) nanofibers on a thin foam-formed fabric from regenerated cellulose fibers. The high filtration efficiency of sub-micron-sized diethylhexyl sebacate (DEHS) aerosol particles resulted from the small mean segment length of 0.35 μm of the nanofiber network. For a particle diameter of 0.6 μm, the filtration efficiency of a single PEO layer varied in the range of 80-97 % depending on the coat weight. The corresponding pressure drop had the level of 20-90 Pa for the airflow velocity of 5.3 cm/s. Using a multilayer structure, a very high filtration efficiency of 99.5 % was obtained with only a slightly higher pressure drop. This opens a route toward designing sustainable personal protective media with improved user experience.

Microplastic and other anthropogenic microparticles in Arctic char (Salvelinus alpinus) and their coastal habitat: A first-look at a central Canadian Arctic commercial fishery

In the recent monitoring guidelines released by the Arctic Monitoring and Assessment Program's Litter and Microplastic Expert Group, Arctic salmonids were recommended as an important species for monitoring plastics in Arctic ecosystems, with an emphasis on aligning microplastic sampling and analysis methods in Arctic fishes. This recommendation was based on the minimal documentation of microplastics in Northern fishes, especially Arctic salmonids. In response, we worked collaboratively with local partners to quantify and characterize microplastics in Arctic char, Salvelinus alpinus, and their habitats in a commercial fishery near Iqaluktuuttiaq (Cambridge Bay), Nunavut. We sampled Arctic char, surface water, and benthic sediments within their summer foraging habitat at Palik (Byron Bay). We found microplastics in 95 % of char with an average of 26 (SD ± 19) particles per individual. On average, surface water samples had 23 (SD ± 12) particles/L and benthic sediment <1 particles/gww. This is the first documentation of plastic pollution in Arctic char and their coastal habitats. Future work should evaluate seasonal, temporal and spatial trends for long-term monitoring of microplastics in Arctic fishes and their habitats.

Do Antarctic bivalves present microdebris? The case of Livingston Island

Marine microdebris (MD) seem to be widespread in benthic invertebrates, even in the most remote areas of the planet such as Antarctica, although the information available is still very scarce. Here we provide a detailed quantification and characterization of the MD found on three common bivalve species (Aequiyoldia eightsii, Thracia cf. meridionalis, and Cyclocardia astartoides) inhabiting shallow areas in Johnsons' Bay, Livingston Island (South Shetland Islands, Antarctica) as a snapshot of the MD present. On average, these bivalves contained 0.71 ± 0.89 items per individual and 1.49 ± 2.35 items per gram, being comparable to the few previous existing studies in other Antarctic areas. Nearly half of the organisms analysed here (45.6 %), contained at least one item. No significant differences were found in the three bivalve species. As far as we know, this is the first study to analyse and compare MD in three bivalve species in the Antarctic Peninsula. Although our results indicate bivalves are as not as polluted as in other areas of the planet, this is remarkable since this is considered one of the last pristine areas of the world. Our results point to local activities as the main source of MD pollution in Livingston Island, although global pollution cannot be discarded. We believe this research provides a useful baseline for future studies and will contribute to develop policies and strategies to preserve Antarctic marine ecosystems from MD pollution.

Biodegradation of plastics in the pelagic environment of the coastal zone - Proposed test method under controlled laboratory conditions

The increasing quantities of plastic litter accumulated in the oceans, including microplastics, represent a serious environmental threat. Despite the recent legislative actions, the plastic littering problem will not disappear in a short time. It may, however be ameliorated by replacing conventional non-degradable plastics with bio-based materials biodegradable in marine environment (targeting the non-recycled or mismanaged plastic waste). Although priority is set to prevention of plastic litter by means of the circular economy principles, biodegradability is a means of controlling unintentional plastic pollution. In this effort, the development of reliable test methods that would be used along with standard specifications for determining the biodegradability of novel polymeric materials or plastics in marine environments, is a necessary complementary component of the whole strategy to control the marine plastic litter and micro-, nano-plastics threat. The present work focuses on identifying gaps and improving available laboratory test methods for measuring the aerobic biodegradation of plastics in the seawater column within the coastal zone (pelagic environment). The research work followed a methodology that is based on recommendations of ASTM D6691:2017 concerning biodegradation of plastics in the seawater and the similar ISO 23977-1:2020. Three different implementation schemes of the test method were applied using different experimental setups and measuring techniques for monitoring the evolved CO2. The effect of critical parameters affecting nutrient adequacy (concentration in inoculum) and oxygen adequacy (bioreactor size, sample size, frequency of aeration) on the biodegradation of four tested materials was explored, and optimal values are proposed. The results allowed for the refinement of the proposed test method to improve reliability and reproducibility.

Influence of synthetic and natural microfibers on the growth, substance exchange, energy accumulation, and oxidative stress of field-collected microalgae compared with microplastic fragment

Synthetic microfibers (MFs), which are Microplastics (MPs), have not received attention commensurate with their abundance in the environment. Currently, limited studies on MFs have focused on their effects on marine organisms. It is therefore necessary to conduct exposure experiments of MFs on freshwater organisms to provide reference data for the ecological risk assessment of MFs. As a primary producer in freshwater ecosystems, microalgae have an ecological niche that is highly overlapping with that of MFs. In this study, we examined the effects of MFs on the growth of Chlorella and indicators of oxidative stress to examine their potential risk on the microalgae population. The results showed that inhibition rate of microalgae increased with MF concentration in the range of 0.01-100 mg/L. Compared with natural fibers such as cotton and wool, PET and PP fibers showed significant growth inhibition, but less so when in fragment form with the same material and concentration. PP and PET particles, whether fibers or fragments, increased the total antioxidant capacity of microalgal cells and caused oxidative damage. To determine the influence of MFs on the interaction of cells in the environment, the exchanged substances and accumulated energy of microalgae cells were also detected. The results indicated that PP and PET fibers, as well as fragments, increased the diameter and membrane permeability of microalgae cell, thus interfering with the cell division and substance exchange processes. PET fibers and fragments showed different interactions at the level of individual cells and populations. This suggests that the evaluation of MPs should consider examinations from cells to population and even community levels in the future.

Novel strategy for treating high salinity oilfield produced water: Pyrite-activated peroxymonosulfate coupled with heterotrophic ammonia assimilation

Existing conventional biological treatment techniques face numerous limitations in effectively removing total petroleum hydrocarbons (TPHs) and ammonia (NH4+-N) from oilfield-produced water (OPW), highlighting the pressing need for innovative pre-oxidation and biological treatment processes. In this study, a pyrite-activated peroxymonosulfate (PMS)-coupled heterotrophic ammonia assimilation (HAA) system was established to achieve satisfactory system performance for OPW treatment. Pyrite sustained-release Fe2+-activated PMS was used to produce SO4•- and •OH, and 71.0 % of TPHs were effectively removed from the oil wastewater. The average TPHs and NH4+-N removal efficiencies in the test group with pre-oxidation were 96.9 and 98.3 %, compared to 46.5 and 77.1 % in the control group, respectively. The maximum fluorescence intensities of tryptophan protein and aromatic protein in the test group declined by 83.7 %. Fourier transform ion cyclotron resonance mass spectrometry revealed that pre-oxidation degraded more long-chain hydrocarbons and aromatic family compound, whereas the HAA process produced more proteins and carbohydrates. Pyrite-PMS promoted the enrichment of ammonia-assimilating bacteria, alleviating the explosive increase in extracellular polymeric substances and reducing sludge settleability. The low cost, efficiency, green chemistry principles, and synergies of this approach make it a powerful solution for practical OPW treatment to reduce environmental impacts and promote sustainable wastewater treatment.

Cellulosic and microplastic fibers in the Antarctic fish Harpagifer antarcticus and Sub-Antarctic Harpagifer bispinis

Human settlements within the Antarctic continent have caused significant coastal pollution by littering plastic. The present study assessed the potential presence of microplastics in the gastrointestinal tract of the Antarctic fish Harpagifer antarcticus, endemic to the polar region, and in the sub-Antarctic fish Harpagifer bispinis. H. antarcticus. A total of 358 microfibers of multiple colors were found in 89 % of H. antarcticus and 73 % of H. bispinis gastrointestinal track. A Micro-FTIR analysis characterized a sub-group (n = 42) of microfibers. It revealed that most of the fibers were cellulose (69 %). Manmade fibers such as microplastics polyethylene terephtalate, acrylics, and semisynthetic/natural cellulosic fibers were present in the fish samples. All the microfibers extracted were textile fibers of blue, black, red, green, and violet color. Our results suggest that laundry greywater discharges of human settlements near coastal waters in Antarctica are a major source of these pollutants in the Antarctic fish.

Biocompatible and Biodegradable 3D Printing from Bioplastics: A Review

There has been a lot of interest in developing and producing biodegradable polymers to address the current environmental problem caused by the continued usage of synthetic polymers derived from petroleum products. Bioplastics have been identified as a possible alternative to the use of conventional plastics since they are biodegradable and/or derived from renewable resources. Additive manufacturing, also referred to as 3D printing, is a field of growing interest and can contribute towards a sustainable and circular economy. The manufacturing technology also provides a wide material selection with design flexibility increasing its usage in the manufacture of parts from bioplastics. With this material flexibility, efforts have been directed towards developing 3D printing filaments from bioplastics such as Poly (lactic acid) to substitute the common fossil- based conventional plastic filaments such as Acrylonitrile butadiene styrene. Plant biomass is now utilized in the development of biocomposite materials. A lot of literature presents work done toward improving the biodegradability of printing filaments. However, additive manufacture of biocomposites from plant biomass is faced with printing challenges such as warping, low agglomeration between layers and poor mechanical properties of the printed parts. The aim of this paper is to review the technology of 3D printing using bioplastics, study the materials that have been utilized in this technology and how challenges of working with biocomposites in additive manufacture have been addressed.

Review of research on migration, distribution, biological effects, and analytical methods of microfibers in the environment

Microplastics have been proven to be one of the critical environmental pollution issues. Moreover, microfibers, the most prominent form of microplastics in the environment, have likewise attracted the attention of various countries. With the increase in global population and industrialization, the production and use of fibers continue to increase yearly. As a result, a large number of microfibers are formed. If fiber products are not used or handled correctly, it will cause direct/indirect severe microfiber environmental pollution. Microfibers will be further broken into smaller fiber fragments when they enter the natural environment. Presently, researchers have conducted extensive research in the identification of microfibers, laying the foundation for further resourcefulness research. This work used bibliometric analysis to review the microfiber contamination researches systematically. First, the primary sources of microfibers and the influencing factors are analyzed. We aim to summarize the influence of the clothing fiber preparation and care processes on microfiber formation. Then, this work elaborated on the migration in/between water, atmosphere, and terrestrial environments. We also discussed the effects of microfiber on ecosystems. Finally, microfibers' current and foreseeable effective treatment, disposal, and resource utilization methods were explained. This paper will provide a structured reference for future microfiber research.

EFFECTS OF HIGH-INTENSITY TRAINING ON BASKETBALL PLAYERS

ABSTRACT Introduction: Basketball represents much more than a high-intensity exercise. Like most ball games, it is a continuous movement system. Objective: Study the effect of high-intensity interval training (HIT) on the aerobic metabolism of young basketball players. Methods: The author randomly divided male basketball players into an upper limb HIT group, lower limb HIT group, and control group by experimental method and statistical analysis, the control group received routine training, and aerobic exercise capacity was measured by increasing load test before and after the experiment. Results: During the lower extremity experiment, the mean power (MP) and peak power (PP) of the 4th full-force pedal stroke in the lower extremity HIT group increased (P<0.05), and the T/C ratio of the lower extremity HIT group was also implemented (P<0.05). There was no significant change in the indices of the control group (P>0.05). Conclusion: Upper extremity HIT in young male basketball players improved only upper extremity aerobic exercise capacity. In contrast, lower-extremity HIT improved both upper-extremity aerobic exercise capacity and lower-extremity anaerobic exercise capacity. Level of evidence II; Therapeutic studies - investigating treatment outcomes.

Detection and characterisation of microplastics and microfibres in fishmeal and soybean meal

Aquaculture is an increasingly important source of nutrition for global food security, which is reliant on animal- and plant-based feeds. Anthropogenic particles, including microplastics and semi-synthetic cellulosic fibres, are prolific marine pollutants that are readily consumed by marine organisms, including small pelagic fish commonly used in fishmeal. Conversely, there is no indication plants can accumulate anthropogenic microparticles. We explore whether aquaculture feed presents a route of contamination for farmed fish. Commercially-sourced aquaculture feedstocks, including fishmeals and soybean meal, were processed (KOH digestion and ZnCl₂ density separation) and anthropogenic particles characterised using microscopy and spectroscopic methods. Both fishmeal and soybean meals contained anthropogenic particles, with concentrations ranging 1070-2000 particles kg^-1. The prevalence of anthropogenic particles in plant-based feeds indicates that the majority of contamination occurs post-harvest. Based on our findings, farmed Atlantic salmon may be exposed to a minimum of 1788-3013 anthropogenic particles from aquaculture feed across their commercial lifespan.

Microfiber shedding from nonwoven materials including wipes and meltblown nonwovens in air and water environments

Nonwoven products are widely used in disposable products, such as wipes, diapers, and masks. Microfibers shed from these products in the aquatic and air environment have not been fully described. In the present study, 15 commercial single-use nonwoven products (wipes) and 16 meltblown nonwoven materials produced in a pilot plant were investigated regarding their microfiber generation in aquatic and air environments and compared to selected textile materials and paper tissue materials. Microfibers shed in water were studied using a Launder Ometer equipment (1-65 mg of microfibers per gram material), and microfibers shed in air were evaluated using a dusting testing machine that shakes a piece of the nonwoven back and forth (~ 4 mg of microfibers per gram material). The raw materials and bonding technologies affected the microfiber generation both in water and air conditions. When the commercial nonwovens contained less natural cellulosic fibers, less microfibers were generated. Bonding with hydroentangling and/or double bonding by two different bonding methods could improve the resistance to microfiber generation. Meltblown nonwoven fabrics generated fewer microfibers compared to the other commercial nonwovens studied here, and the manufacturing factors, such as DCD (die-to-collector distance) and air flow rate, affected the tendency of microfiber generation. The results suggest that it is possible to control the tendency of microfiber shedding through the choice of operating parameters during nonwoven manufacturing processes.

Time-lagged interspecies interactions prevail during biofilm development in moving bed biofilm reactor

Clarifying the essential succession dynamics of interspecies interactions during biofilm development is crucial for the regulation and application of biofilm-based processes. In this study, regular and time-series phylogenetic molecular ecological networks (pMENs) were constructed to investigate ordinary and time-lagged interspecies interactions during biofilm development in a moving bed biofilm reactor (MBBR). Positive interactions dominated both regular (89.78%) and time-series (77.04%) ecological networks, suggesting that extensive cooperative behaviors facilitated biofilm development. The pronounced directional interactions (72.52%) in the time-series network further indicated that time-lagged interspecies interactions prevailed in the biofilm development process. Specifically, the proportion of directional negative interactions was higher than that of positive interactions, implying that interspecific competition preferred to be time-lagged. The time-series network revealed that module hubs exhibited extensive time-lagged positive interactions with their neighbors, and most of them exhibited altruistic behaviors. Keystone species possessing more positive interactions were positively correlated with biofilm biomass, NO₃ ^- -N concentrations, and the removal efficiencies of NH₄ ⁺ -N and COD. However, keystone species and peripherals that were negatively targeted by their neighbors showed positive correlations with the concentrations of NO₂ ^- -N, polysaccharides, and proteins in the soluble microbial products. The data highlight that the time-series network can provide directional microbial interactions along with the biofilm development process, which would help to predict the tendency of community shifts and propose efficient strategies for the regulation of biofilm-based processes. This article is protected by copyright. All rights reserved.

Degradation of Cellulose Derivatives in Laboratory, Man-Made, and Natural Environments

Biodegradable polymers complement recyclable materials in battling plastic waste because some products are difficult to recycle and some will end up in the environment either because of their application or due to wear of the products. Natural biopolymers, such as cellulose, are inherently biodegradable, but chemical modification typically required for the obtainment of thermoplastic properties, solubility, or other desired material properties can hinder or even prevent the biodegradation process. This Review summarizes current knowledge on the degradation of common cellulose derivatives in different laboratory, natural, and man-made environments. Depending on the environment, the degradation can be solely biodegradation or a combination of several processes, such as chemical and enzymatic hydrolysis, photodegradation, and oxidation. It is clear that the type of modification and especially the degree of substitution are important factors controlling the degradation process of cellulose derivatives in combination with the degradation environment. The big variation of conditions in different environments is also briefly considered as well as the importance of the proper testing environment, characterization of the degradation process, and confirmation of biodegradability. To ensure full sustainability of the new cellulose derivatives under development, the expected end-of-life scenario, whether material recycling or "biological" recycling, should be included as an important design parameter.

Biodegradable Nonwoven Materials with Antipathogenic Layer

Biopolymer composites have received increasing attention for their beneficial properties such as being biodegradable and having less influence to the environment. Biodegradability of materials has become a desired feature due to the growing problems connected with waste management. The aim of the paper is to emphasize the importance of biodegradable textile materials, especially nonwoven materials with an anti-pathogenic layer. The article refers to the definitions of biodegradation, degradation and composting processes, as well as presenting methods of testing biodegradability depending on the type of material. The study gives examples of biodegradation of textiles and presents examples of qualitative and quantitative methods used for testing antimicrobial activity of biodegradable nonwovens with an anti-pathogenic layer.

The impact of fabric conditioning products and lint filter pore size on airborne microfiber pollution arising from tumble drying

Vented tumble dryers release moist warm air from the drying process to the external environment, usually through pipework linking the appliance to a vent in an exterior wall. Although such dryers contain a lint filter to remove fibers from this air stream, recent reports suggest that this process is incomplete, leading to microfibers being released in the ducted warm air and subsequently polluting the external environment. Microfiber release from wash loads comprising 10 100% cotton and 10 100% polyester T-shirts (total load mass ratio 48% cotton, 52% polyester) was measured at different stages of the washing and drying process to compare the quantities of fibers released ‘down the drain’, collected in the dryer lint filter, and released to air from the tumble dryer. Testing under both European and North American washing conditions found that the quantities of microfibers released to air during tumble drying were significant and comparable to levels released ‘down the drain’ during washing. Use of conventional rinse-added liquid fabric conditioner increased microfiber accumulation on the dryer lint filter, with reduced release from the dryer exhaust observed at the highest fabric conditioner dose tested (21.6% and 14.2% reduction under North American and European conditions, respectively). Conventional liquid fabric conditioner did not significantly impact microfiber release from the washing machine, in line with previous studies. A fabric conditioner specially designed for anti-wrinkle performance reduced microfiber release from the dryer exhaust at all levels tested (by 17.6–35.6%, depending on dose), apparently by increasing the efficiency of microfiber accumulation in the lint filter. Tumble dryer sheets were also found to cause a reduction in microfiber release from the dryer exhaust (by 14.1–34.9%, depending on the dose/product), likely driven by collection of liberated fibers on the sheet during the drying process. The use of both antiwrinkle liquid fabric conditioner and dryer sheet enabled a 44.9% reduction in microfiber emissions from the dryer exhaust. In all studies, the fiber mass collected on the lint filter or emitted from the dryer exhaust was richer in cotton fibers (range 83.4–96.3% on the lint filter, 93.0–99.8% from the dryer exhaust) than the wash load composition (48% cotton). Moreover, fibers collected by the lint filter contained a higher proportion of polyester than emissions from the dryer exhaust (range 3.7–16.6% on the lint filter, 0.2–7.0% from the dryer exhaust). There is significant variation in the porosity of lint filters among installed vented tumble dryers. Single-variable testing of the impact of lint filter design concluded that reducing screen pore size significantly reduces airborne microfiber release during tumble drying; a reduction in lint filter pore size from 0.2 mm² to 0.04 mm² reduced release by 34.8%. As some lint filters have pore sizes of around 1 mm², there is enormous scope to reduce microfiber release from dryers though improved lint filter design. However, it is suggested that a step-change in appliance design away from vented dryers to only fully-sealed condenser dryers might be necessary to eliminate the contribution of tumble drying to airborne microfiber pollution.

Are We Underestimating Anthropogenic Microfiber Pollution? A Critical Review of Occurrence, Methods, and Reporting

Anthropogenic microfibers, a ubiquitous environmental contaminant, can be categorized as synthetic, semisynthetic, or natural according to material of origin and production process. Although natural fibers, such as cotton and wool, originated from natural sources, they often contain chemical additives, including colorants (e.g., dyes, pigments) and finishes (e.g., flame retardants, antimicrobial agents, ultraviolet light stabilizers). These additives are applied to textiles during production to give textiles desired properties like enhanced durability. Anthropogenically modified "natural" and semisynthetic fibers are sufficiently persistent to undergo long-range transport and accumulate in the environment, where they are ingested by biota. Although most research and communication on microfibers have focused on the sources, pathways, and effects of synthetic fibers in the environment, natural and semisynthetic fibers warrant further investigation because of their abundance. Because of the challenges in enumerating and identifying natural and semisynthetic fibers in environmental samples and the focus on microplastic or synthetic fibers, reports of anthropogenic microfibers in the environment may be underestimated. In this critical review, we 1) report that natural and semisynthetic microfibers are abundant, 2) highlight that some environmental compartments are relatively understudied in the microfiber literature, and 3) report which methods are suitable to enumerate and characterize the full suite of anthropogenic microfibers. We then use these findings to 4) recommend best practices to assess the abundance of anthropogenic microfibers in the environment, including natural and semisynthetic fibers. By focusing exclusively on synthetic fibers in the environment, we are neglecting a major component of anthropogenic microfiber pollution. Environ Toxicol Chem 2022;41:822-837. © 2021 SETAC.

Methodologies to Assess the Biodegradability of Bio-Based Polymers—Current Knowledge and Existing Gaps

Our society lives in a time of transition where traditional petroleum-based polymers/plastics are being replaced by more sustainable alternative materials. To consider these bioproducts as more viable options than the actual ones, it is demanded to ensure that they are fully biodegradable or compostable and that there is no release of hazardous compounds to the environment with their degradation. It is then essential to adapt the legislation to support novel specific guidelines to test the biodegradability of each biopolymer in varied environments, and consequently, establish consistent data to design a coherent labeling system. This review work aims to point out the current standards that can serve as a basis for the characterization of biopolymers’ biodegradation profile in different environments (soil, compost, and aquatic systems) and identify other laboratory methodologies that have been adopted for the same purpose. With the information gathered in this work, it was possible to identify remaining gaps in existing national and international standards to help establish new validation criteria to be introduced in future research and policies related to bioplastics to boost the sustainable progress of this rising industry.

Seeking for a perfect (non-spherical) microplastic particle - The most comprehensive review on microplastic laboratory research

In recent decades, much attention has been paid to microplastic pollution, and research on microplastics has begun to grow exponentially. However, microplastics research still suffers from the lack of standardized protocols and methods for investigation of microplastics under laboratory conditions. Therefore, in this review, we summarize and critically discuss the results of 715 laboratory studies published on microplastics in the last five years to provide recommendations for future laboratory research. Analysis of the data revealed that the majority of microplastic particles used in laboratory studies are manufactured spheres of polystyrene ranging in size from 1 to 50 µm, that half of the studies did not characterize the particles used, and that a minority of studies used aged particles, investigated leaching of chemicals from microplastics, or used natural particles as a control. There is a large discrepancy between microplastics used in laboratory research and those found in the environment, and many laboratory studies suffer from a lack of environmental relevance and provide incomplete information on the microplastics used. We have summarized and discussed these issues and provided recommendations for future laboratory research on microplastics focusing on (i) microplastic selection, (ii) microplastic characterization, and (iii) test design of laboratory research on microplastics.

Anthropogenic microfibres flux in an Antarctic coastal ecosystem: The tip of an iceberg?

This study describes the occurrence of anthropogenic microfibres (AMFs) found in sediment trap samples collected at 25 m water depth in an Antarctic fjord (Potter Cove, King George/25 de Mayo Island) from 2012 to 2015. During visual sorting of samples, AMFs were detected and described, and a subset was confirmed, via FTIR (Fourier transform infrared) spectroscopy, as semi-synthetic cellulosic and polyacrylonitrile polymers. Estimated flux of AMF varied from 115 to 152,750 microfibres m^-2 throughout the studied period, with sizes ranging from 10 to 450 μm in length. Maximum AMFs fluxes occurred in summer months. Sediment traps allowed detecting temporal patterns of small (μm) AMFs, usually undersampled with nets or sieves, providing a new insight into microplastic pollution in Antarctica and its relation to environmental conditions.

Strategies and progress in synthetic textile fiber biodegradability

Abstract

The serious issue of textile waste accumulation has raised attention on biodegradability as a possible route to support sustainable consumption of textile fibers. However, synthetic textile fibers that dominate the market, especially poly(ethylene terephthalate) (PET), resist biological degradation, creating environmental and waste management challenges. Because pure natural fibers, like cotton, both perform well for consumer textiles and generally meet certain standardized biodegradability criteria, inspiration from the mechanisms involved in natural biodegradability are leading to new discoveries and developments in biologically accelerated textile waste remediation for both natural and synthetic fibers. The objective of this review is to present a multidisciplinary perspective on the essential bio-chemo-physical requirements for textile materials to undergo biodegradation, taking into consideration the impact of environmental or waste management process conditions on biodegradability outcomes. Strategies and recent progress in enhancing synthetic textile fiber biodegradability are reviewed, with emphasis on performance and biodegradability behavior of poly(lactic acid) (PLA) as an alternative biobased, biodegradable apparel textile fiber, and on biological strategies for addressing PET waste, including industrial enzymatic hydrolysis to generate recyclable monomers. Notably, while pure PET fibers do not biodegrade within the timeline of any standardized conditions, recent developments with process intensification and engineered enzymes show that higher enzymatic recycling efficiency for PET polymer has been achieved compared to cellulosic materials. Furthermore, combined with alternative waste management practices, such as composting, anaerobic digestion and biocatalyzed industrial reprocessing, the development of synthetic/natural fiber blends and other strategies are creating opportunities for new biodegradable and recyclable textile fibers.

Article Highlights

Circulation of fibrous microplastic (microfiber) in sewage and sewage sludge treatment processes

The fate of microplastics (MPs) in the sewage treatment process has been investigated worldwide, and novel results have been reported; few studies have also clarified the fate of MPs in the sewage sludge treatment process. Although most MPs in sewage are transferred to sludge, some flow back from the sludge treatment process to the sewage treatment process. Therefore, throughout the sewage treatment plant, the removal rate of MPs may increase via a countermeasure during the sludge treatment process. In this study, samples obtained from sewage and sewage sludge treatments were used to degrade organic matter with hydrogen peroxide. Water sample particles were trapped on Ni filters with 20-μm-sized pores, dried at room temperature and then the MPs were detected and identified by FTIR microscopy. Note that sludge samples were treated with hydrogen peroxide and separated by specific gravity using NaI solution. The concentration of MPs per unit volume was then calculated and the MPs load was estimated using flow rates of water and sludge. Subsequently, we clarified the fate of MPs with sizes of 20 μm or greater in a sewage treatment plant. When the MPs load in the influent sewage is 100%, 12% of the MPs were found to return to the sewage treatment process via the sidestream of the sludge treatment process. Per this observation, it was made evident that MPs are in fact circulating throughout the sewage and sludge treatment processes. MPs in the sidestream mainly consisted of the effluent from the sludge concentration process, and most MPs were thought to be fibrous polyethylene terephthalate (fibrous MPs, i.e. microfibers [MFs]). The results show that MFs circulate throughout the sewage and sludge treatment processes, and for effectively increasing the removal rate of MPs, the removal of MFs proves correspondingly effective during the sludge treatment process.

Degradation of synthetic and wood-based cellulose fabrics in the marine environment: Comparative assessment of field, aquarium, and bioreactor experiments

As global production of textiles rapidly grows, there is urgency to understand the persistence of fabrics in the marine environment, particularly from the microfibers they shed during wearing and washing. Here, we show that fabrics containing polyester (one of the most common plastics) remained relatively intact (viz., with a limited biofilm) after >200 days in seawater off the Scripps Oceanography pier (La Jolla, CA), in contrast to wood-based cellulose fabrics that fell apart within 30 days. We also show similar results under experimental aquaria (in open circuit with the pier waters) as well as bioreactor settings (in close circuit, using microbial inoculum from the North Sea, off Belgium), using nonwoven fabrics and individual fibers, respectively. The fact that fibers released from synthetic textiles remain persistent and non-biodegradable despite their small (invisible) size, highlights concern for the growing industry that uses polyester from recycled plastics to make clothing.

Discharge of microplastics fibres from wet wipes in aquatic and solid environments under different release conditions

This study warns regarding the possibility of microplastics (MPs) release from wet wipes and further in the environment and examines the potential associated risks. The exposure of humans to MPs during cleaning, and their discharge into wastewater treatment processes through flushing in toilets/basins was simulated by rubbing wet wipes on hands and immersing them in water, respectively. Wet wipes can be stored in a waste bin and subsequently disposed of through waste treatment or directly disposed in aquatic environments. The released MPs were identified and quantified using Fourier transform infrared spectroscopy. The released MPs were in the fibre form, and their major component was polyester. A higher number of MP fibres (693-1066 p/sheet) was released when the wet wipe was exposed to the aquatic environment compared to rubbing the wet wipe on hands or solid materials (180-106 p/sheet) or both. In particular, wet wipes in the wet state released the highest number (1966 p/sheet) of MP fibres. Unexpectedly, the least number of MP fibres was released by rubbing them on the hands/solid (180-200 p/sheet). Most fibres (>90%) were more than 100 μm, and those above 300 μm accounted for more than 40%-60% of the total number of detected MP fibres. This implies that long MP fibres released into the environment could disrupt the health of the aquatic ecosystem owing to their bioaccumulation, retention time, intestinal toxicity, and the transfer of persistent organic matter to aquatic organisms.

Microbial Diversity and Activity During the Biodegradation in Seawater of Various Substitutes to Conventional Plastic Cotton Swab Sticks

The European Parliament recently approved a new law banning single-use plastic items for 2021 such as plastic plates, cutlery, straws, cotton swabs, and balloon sticks. Transition to a bioeconomy involves the substitution of these banned products with biodegradable materials. Several materials such as polylactic acid (PLA), polybutylene adipate terephthalate (PBAT), poly(butylene succinate) (PBS), polyhydroxybutyrate-valerate (PHBV), Bioplast, and Mater-Bi could be good candidates to substitute cotton swabs, but their biodegradability needs to be tested under marine conditions. In this study, we described the microbial life growing on these materials, and we evaluated their biodegradability in seawater, compared with controls made of non-biodegradable polypropylene (PP) or biodegradable cellulose. During the first 40 days in seawater, we detected clear changes in bacterial diversity (Illumina sequencing of 16S rRNA gene) and heterotrophic activity (incorporation of ³H-leucine) that coincided with the classic succession of initial colonization, growth, and maturation phases of a biofilm. Biodegradability of the cotton swab sticks was then tested during another 94 days under strict diet conditions with the different plastics as sole carbon source. The drastic decrease of the bacterial activity on PP, PLA, and PBS suggested no bacterial attack of these materials, whereas the bacterial activity in PBAT, Bioplast, Mater-Bi, and PHBV presented similar responses to the cellulose positive control. Interestingly, the different bacterial diversity trends observed for biodegradable vs. non-biodegradable plastics allowed to describe potential new candidates involved in the degradation of these materials under marine conditions. This better understanding of the bacterial diversity and activity dynamics during the colonization and biodegradation processes contributes to an expanding baseline to understand plastic biodegradation in marine conditions and provide a foundation for further decisions on the replacement of the banned single-used plastics.

Plastic microfibre pollution: how important is clothes' laundering?

Plastic microfibre pollution produced by domestic and commercial laundering of synthetic textiles has recently been incriminated in the press and the scientific literature as the main source (up to 90%) of primary microplastics in the oceans. Polyethylene terephthalate (PET) is the most common microfibre encountered. This review aims to provide updated information on worldwide plastic microfibre pollution caused by textile laundering and some possibilities for its control. Release of microfibres during domestic washing and tumble drying, their fate in wastewater treatment plants (WWTPs) and the oceans, and their environmental effects on the aquatic biota are discussed, as well as potential control methods at the levels of textile modification and laundry procedures. Environmental effects on aquatic biota are important; as a result of their small size and length-to-diameter ratio, microfibers are more effectively incorporated by organisms than other plastic particle groups. Simulation laundering studies may be useful in the development of a Standard Test Method and modification of WWTPs may reduce microfibre release into aquatic systems. However, improvements will be necessary in textile design and appliance design, and recommendations should be made to consumers about reducing their personal impact on the environment through their laundering choices, which can include appliances, fabric care products and washing conditions. Official regulation, such as that introduced recently by the French government, may be necessary to reduce plastic microfibre release from clothes' laundering.

Impact of dyes and finishes on the aquatic biodegradability of cotton textile fibers and microfibers released on laundering clothes: Correlations between enzyme adsorption and activity and biodegradation rates

The presence and biodegradability of textile microfibers shed during laundering or use is an important environmental issue. In this research, the influence of common textile finishes on the persistence of cotton fibers in an aerobic aquatic environment was assessed. The biodegradation of cotton knitted fabrics with different finishes, silicone softener, durable press, water repellent, and a blue reactive dye was evaluated. The rate of biodegradation decreased with durable press and water repellant finishing treatments. In terms of the final extent of biodegradation, there was no significant difference between the samples. All samples reached more than 60% biodegradation in 102 days. The biodegradation rates were in agreement with observed trends of the same samples for cellulase mediated hydrolysis and cellulase adsorption experiments, indicating the finishes impact the initial adsorption of enzymes excreted by the microorganisms and the initial rates of biodegradation, however despite this the cellulosic material maintains its biodegradability.

From source to sink: Review and prospects of microplastics in wetland ecosystems

The source, distribution, migration, and fate of microplastics (MPs) in aquatic and terrestrial ecosystems have received much attention. However, the relevant reports in wetland ecosystems, the boundary area between water and land, are still rare. Where are the sources and sinks of MPs in the wetland? The latest researches have shown that the sources of MPs in wetlands include sewage discharge, surface runoff, and plastic wastes from aquaculture. Fibers and fragments are the most common shapes, and PE, PP, PS can be detected in water or sediment matrices, and biota of wetlands. The distribution is affected by hydrodynamic conditions, sediment properties, and vegetation coverage. Factors affecting the vertical migration of MPs include their own physical and chemical properties, the combination of substances that accelerate deposition (mineral adsorption and biological flocculation), and resuspension. Minerals tend to adsorb negatively charged MPs while algae aggregates have a preference for positively charged MPs. The wetlands vegetation can trap MPs and affect their migration. In water matrices, MPs are ingested by organisms and integrated into sediments, which makes them seem undetectable in the wetland ecosystem. Photodegradation and microbial degradation can further reduce the MPs in size. Although recent research has increased, we are still searching for a methodological harmonization of the detection practices and exploring the migration rules and fate patterns of MPs. Our work is the first comprehensive review of the source, distribution, migration, and fate of MPs in wetland ecosystems. It reveals the uniqueness of wetland habitat in the research of MPs and indicates the potential of wetlands acting as sources or sinks for MPs.

Impact of dyes and finishes on the microfibers released on the laundering of cotton knitted fabrics

The influence of common textile finishes on cotton fabrics on the generation of microfibers during laundering was assessed. Microfiber release was determined to be in the range of 9000-14,000 particles per gram of cotton fabric. Cotton knitted fabrics treated with softener and durable press generate more microfibers (1.30-1.63 mg/g fabric) during laundering by mass and number than untreated fabric (0.73 mg/g fabric). The fabrics treated with softener generated the longest average microfiber length (0.86 mm), whereas durable press and water repellent treatments produced the shortest average microfiber length (0.62 and 0.63 mm, respectively). In general, the changes in the mechanical properties of the fibers and fabrics due to the finishing treatments are the main factor affecting the microfiber release. The abrasion resistance of the fabrics decreases for durable press treatments and water repellent treatments due to the brittleness in the structure originated by the crosslinking treatment. In the case of the softener treatment, the fabric surface is soft and smooth decreasing the friction coefficient between fibers favoring the fibers loosening from the textile and resulting in a high tendency for fuzz formation and microfiber release. These findings are useful for the textile industry in the design and selection of materials and treatments for the reduction of synthetic or natural microfiber shedding from textiles.

Beyond plastic microbeads - Short-term feeding of cellulose and polyester microfibers to the freshwater amphipod Gammarus duebeni

Monitoring studies have revealed the presence of large numbers of natural as well as anthropogenic microfibers, plastic and non-plastic, in environmental samples. However, the interaction of organisms with microfibers is largely understudied. This is the first ecotoxicological study that compares short-term feeding of anthropogenic plastic and non-plastic microfibers on a consumer (leaf-shredding detritivores) species. The freshwater amphipod Gammarus duebeni was selected for this study as it is a model ecotoxicological species. After a 96-hour exposure, 58.3% and 41.7% of the amphipods contained cellulose or polyester fibers in their digestive tracts, respectively. Microfiber ingestion was analysed per polymers in presence or absence of food. The G. duebeni group exposed to 'polyester fibers in presence of food' accumulated highest numbers of microfibers in their digestive tracts (5.2 ± 3.4 MFs/amphipod) followed by those exposed to 'cellulose in presence of food' (2.5 ± 0.9 MFs/amphipod). A significantly (Three-way ANOVA, p-value <0.05) higher number of microfibers was found in the midgut-hindgut (posterior) sections, compared to the foregut (anterior) section. Microfiber uptake had no apparent short-term negative effect on amphipod survival at 96 h. Yet, as amphipods are both predators and prey, and therefore are key species in the aquatic food web, the rapid accumulation of anthropogenic microfibers in their digestive system has potentially further ecological implications. Future studies need to consider the possible transfer of ingested anthropogenic microfibers to higher trophic levels in freshwater communities.

Microplastic fibres from synthetic textiles: Environmental degradation and additive chemical content

Microplastic fibres (MPFs) often make up the largest fraction of microplastic pollution in aquatic environments, yet little is known about their degradative fate and persistence. This study investigates the environmentally relevant photodegradation of common MPFs: polyester (PET), polyamide (PA) and polyacrylonitrile (PAN), their respective additive chemical profile, together with their potential for additive leaching. MPFs were subject to ultraviolet (UV) exposure in seawater and freshwater media over 10 months. PET and PA MPFs showed significant fragmentation and surface changes following UV exposure, additionally PA showed evidence of chemical changes. PAN did not undergo significant photodegradation in the same exposure period. Chemicals tentatively identified in MPFs and aqueous leachates via non-target gas chromatography-mass spectrometry include monomers, UV stabilisers and degradation products. Characterisation of several bisphenols (BPs) and benzophenones (BzPs) was performed via ultraperformance liquid chromatography tandem mass spectrometry. Bisphenol A, bisphenol S and benzophenone-3 were quantified in all MPFs and wool at concentrations between 4.3 and 501 ng/g, with wool displaying the highest sum concentration of BPs and BzPs at 863 and 27 ng/g, respectively.

Microplastics in soils: A review of methods, occurrence, fate, transport, ecological and environmental risks

The global prevalence of microplastics (MPs) poses a potential threat and unpredictable risk to the function and health of environmental systems. However, the research progress of soil MPs is restricted by the inherent technical inconformity and difficulties in analyzing particles in complex matrices. Here, we reviewed a selection of papers and then extrapolated a tentative standardized method for such analyses. The multiple sources of soil MPs in soil need to be quantified. Global monitoring data of soil MPs is far from sufficient. The interaction between MPs and different properties and environmental factors controls the migration and retention of MPs in soil. The migration behavior and key mechanisms of MPs in real-world environments remain to be determined. The presence of MPs threatens soil microbial-plant-animal ecosystem function and health, and may enter the human body through the food chain, although the extent of these hazards is currently debated. In particular, attention should be paid to the potential transport and ecotoxicological mechanisms of contaminants derived and adsorptive from MPs and of harmful microorganisms (such as pathogens) attached as biofilms. Although there exist preliminary studies on soil MPs, it is urgent to consider the diversity of MPs as a suite of contaminants and to systematically understand the sources, flux and effects of these artificial pollutants in time and space from the perspective of plastic environmental cycle. More comprehensive quantification of their environmental fate is undertaken to identify risks to global human and ecological systems. From the perspective of controlling soil MP pollution, the responsibility assignment of government manage-producer-consumer system and the strategy of remediation should be implemented. This review is helpful for providing an important roadmap and inspiration for the research methods and framework of soil MPs and facilitates the development of waste management and remediation strategies for regional soil MP contamination.

Biodegradability of poly(3-hydroxyalkanoate) and poly(ε-caprolactone) via biological carbon cycles in marine environments

Approximately 4.8–12.7 million tons of plastic waste has been estimated to be discharged into marine environments annually by wind and river currents. The Ellen MacArthur Foundation warns that the total weight of plastic waste in the oceans will exceed the total weight of fish in 2050 if the environmental runoff of plastic continues at the current rate. Hence, biodegradable plastics are attracting attention as a solution to the problems caused by plastic waste. Among biodegradable plastics, polyhydroxyalkanoates (PHAs) and poly(ε-caprolactone) (PCL) are particularly noteworthy because of their excellent marine biodegradability. In this review, the biosynthesis of PHA and cutin, a natural analog of PCL, and the biodegradation of PHA and PCL in carbon cycles in marine ecosystems are discussed. PHA is biosynthesized and biodegraded by various marine microbes in a wide range of marine environments, including coastal, shallow-water, and deep-sea environments. Marine cutin is biosynthesized by marine plants or obtained from terrestrial environments, and PCL and cutin are biodegraded by cutin hydrolytic enzyme-producing microbes in broad marine environments. Thus, biological carbon cycles for PHA and PCL exist in the marine environment, which would allow materials made of PHA and PCL to be quickly mineralized in marine environments.