Composite polyvinylidene fluoride (PVDF) membrane impregnated with Fe2O3 nanoparticles and multiwalled carbon nanotubes for catalytic degradation of organic contaminants

Effect of basic and basic/acid modifications on the surface of PVDF membranes for the insertion of TiO2 and its use in environmental applications

Supporting titanium oxide (TiO2) on polymeric membrane surfaces is a strategy to increase the photocatalytic activity of this material as well as to modify membrane surface with antifouling properties or to develop hybrid processes of water treatment. The chemical characteristics of the polymeric membrane surfaces are a determining factor in the correct impregnation of TiO2 particles. In this work, the titanium oxide was immobilized on polyvinylidene fluoride (PVDF) membrane surface by direct impregnation during the synthesis of the inorganic particles by sol-gel route. The PVDF membranes were previously modified by treatments based on an alkaline attack followed by acid treatment. The final TiO2-modified membranes were characterized by infrared and Raman spectroscopy, as well as by scanning electron microscopy. In addition, the changes on the surface characteristics were determined by contact angle measurements. Finally, the membranes were tested on the photocatalytic degradation of methyl orange (MO). The results obtained indicate that the basic/acid pretreatment allows the generation of active sites in the membrane and that when carrying out the synthesis of TiO2 on the membrane, it can be anchored stably on its surface and through the pores. The microscopies indicate that the structure of the membrane is not compromised by the pretreatment. The amount of TiO2 deposited on the membrane was of 0.1580 ± 0.01773 mg TiO2/cm2 membrane. With this amount of TiO2, a degradation percentage of 98.2% is achieved after 450 min; when the membrane is used for a second cycle, a degradation percentage of 82.0% is obtained, which remains constant for 3 subsequent cycles. This method, which uses the PVDF membrane as a support for TiO2 particles, represents a low-cost and easy-to-prepare insertion procedure, with good degradation percentages, which means that the membrane can be used for subsequent studies in filtration systems in the treatment of effluents from the textile industry.

Membrane-based nanoconfined heterogeneous catalysis for water purification: A critical review✰

Progress in heterogeneous advanced oxidation processes (AOPs) is hampered by several issues including mass transfer limitation, limited diffusion of short-lived reactive oxygen species (ROS), aggregation of nanocatalysts, and loss of nanocatalysts to treated water. These issues have been addressed in recent studies by executing the heterogeneous AOPs in confinement, especially in the nanopores of catalytic membranes. Under nanoconfinement (preferably at the length of less than 25 nm), the oxidant-nanocatalyst interaction, ROS-micropollutant interaction and diffusion of ROS have been observed to significantly improve, which results in enhanced ROS yield and mass transfer, improved reaction kinetics and reduced matrix effect as compared to conventional heterogenous AOP configuration. Given the significance of nanoconfinement effect, this study presents a critical review of the current status of membrane-based nanoconfined heterogeneous catalysis system for the first time. A succinct overview of the nanoconfinement concept in the context of membrane-based nanofluidic platforms is provided to elucidate the theoretical and experimental findings related to reaction kinetics, reaction mechanisms and molecule transport in membrane-based nanoconfined AOPs vs. conventional AOPs. In addition, strategies to construct membrane-based nanoconfined catalytic systems are explained along with conflicting arguments/opinions, which provides critical information on the viability of these strategies and future research directions. To show the desirability and applicability of membrane-based nanoconfined catalysis systems, performance governing factors including operating conditions and water matrix effect are particularly focused. Finally, this review presents a systematic account of the opportunities and technological constraints in the development of membrane-based nanoconfined catalytic platform to realize effective micropollutant elimination in water treatment.

The enhancement of dye filtration performance and antifouling properties in amino-functionalized bentonite/polyvinylidene fluoride mixed matrix membranes

Trade-off issue and membrane fouling remain two major issues in the utilization of membrane technology for the water treatment due to reduced membrane permeability and lifetime. In our study, we employed 3-aminopropyltriethoxysilane modified bentonite (BNTAPS) as an anti-fouling modifier to prepare polyvinylidene fluoride (PVDF)-based membranes via the phase inversion method. The effects of BNTAPS concentration on the physical, mechanical, morphological, and filtration performance of the hybrid membranes have been investigated. It was found that the addition of BNTAPS improved the hydrophilicity of the membrane revealed by the decreased water contact angle. Consequently, the pure water flux of PVDF membrane containing 0.5% BNTAPS (PVDF/BNTAPS0.5%) increased to 35.5 L m^-2 h^-1. Moreover, the PVDF/BNTAPS membrane showed a smaller pore diameter and porosity compared to pristine PVDF. The membrane performance evaluation was carried out using cationic and anionic dyes, i.e., methylene blue (MB) and acid yellow (AY17), respectively. Our study revealed that the rejection of each dye was slightly increased for the PVDF/BNTAPS0.5%. However, the flux recovery rate of the PVDF/BNTAPS membrane significantly improved, which directly prolonged the membrane lifetime.

Catalytic membrane-based oxidation-filtration systems for organic wastewater purification: A review

Catalytic membranes can simultaneously realize physical separation and chemical oxidation in one integrated system, which is the frontier technology for effective removal of organic containments in wastewater treatment. The catalytic membrane coupled with advanced oxidation processes (AOPs) not only significantly enhances the pollutant removal efficiency but also inhibits the fouling of the membrane via self-cleaning. In this review, the preparation approaches of catalytic membranes including blending, surface coating, and bottom-up synthesis are comprehensively summarized. The different integrated catalytic membrane systems coupled with photocatalysis, Fenton oxidation, persulfate activations, ozonation and electrocatalytic oxidation are discussed in terms of mechanisms and performance. Besides, the principles, influencing factors, advantages and issues of the different catalytic membrane/oxidation systems are outlined comparatively. Finally, the future challenges, and research directions are suggested, which is conducive to the design and development of catalytic membrane-oxidation systems for practical remediation of organic containing wastewater.

Membrane-Confined Iron Oxychloride Nanocatalysts for Highly Efficient Heterogeneous Fenton Water Treatment

Heterogeneous advanced oxidation processes (AOPs) allow for the destruction of aqueous organic pollutants via oxidation by hydroxyl radicals (^•OH). However, practical treatment scenarios suffer from the low availability of short-lived ^•OH in aqueous bulk, due to both mass transfer limitations and quenching by water constituents, such as natural organic matter (NOM). Herein, we overcome these challenges by loading iron oxychloride catalysts within the pores of a ceramic ultrafiltration membrane, resulting in an internal heterogeneous Fenton reaction that can degrade organics in complex water matrices with pH up to 6.2. With ^•OH confined inside the nanopores (∼ 20 nm), this membrane reactor completely removed various organic pollutants with water fluxes of up to 100 L m^-2 h^-1 (equivalent to a retention time of 10 s). This membrane, with a pore size that excludes NOM (>300 kDa), selectively exposed smaller organics to ^•OH within the pores under confinement and showed excellent resiliency to representative water matrices (simulated surface water and sand filtration effluent samples). Moreover, the membrane exhibited sustained AOPs (>24 h) and could be regenerated for multiple cycles. Our results suggest the feasibility of exploiting ultrafiltration membrane-based AOP platforms for organic pollutant degradation in complex water scenarios.

Preparation of PVDF/CdS/Bi2WO6/ZnO hybrid membrane with enhanced visible-light photocatalytic activity for degrading nitrite in water

In this work, a visible light-driven ternary heterojunction photocatalyst, CdS/Bi₂WO₆/ZnO, was synthesized using hydrothermal, ultrasonic dispersion, and deposition precipitation methods. The results show that photocatalysts with flower-like heterostructures were obtained, which could efficiently separate electron-hole pairs, and the photocatalytic activity was thereby significantly enhanced. Furthermore, CdS/Bi₂WO₆/ZnO and polyvinylidene fluoride (PVDF) were used to fabricate hybrid membranes via a phase-conversion method. The samples were characterized using SEM, TEM, EDX, XRD, DRS, XPS, PL, and N₂ adsorption-desorption isotherms, and the transient photocurrent response. The photocatalytic activity of the hybrid membrane was evaluated, and 92.58% of the nitrite was converted into non-toxic substances within 4 h under simulated sunlight irradiation. This result indicated that the photocatalyst exhibited a good photocatalytic activity after immobilization. The possible mechanism was elucidated by studying the product during the photocatalytic degradation, and the effects of different pH values, electron scavengers, and hole scavengers on the photocatalytic performance were further investigated.

Fe3O4/PVDF catalytic membrane treatment organic wastewater with simultaneously improved permeability, catalytic property and anti-fouling

Fe₃O₄/Polyvinylidene fluoride (PVDF) three-channel hollow fiber catalytic membrane was successfully fabricated via non-solvent induced phase inversion and used for organic wastewater degradation in this work. The effects of Fe₃O₄ nanoparticles addition on the surface and cross-section morphologies, hydrophilicity and thermal properties of the catalytic membrane were characterized by the field emission scanning electron microscopy (SEM), water contact angle and thermogravimetric analysis (TGA), respectively. The obtained catalytic membrane exhibited good hydrophilicity, a high pure water flux of 175.8 L m^-2 h^-1 and a high removal of methylene blue (up to 97.6%) with Fenton catalytic reaction. Meanwhile, the catalytic membrane shows excellent anti-fouling property due to the presence of Fenton reaction. Our results show that Fe₃O₄/PVDF three-channel hollow fiber catalytic membrane was a promising alternative for the degradation of organic contaminants.

Direct contact ultrasound for fouling control and flux enhancement in air-gap membrane distillation

Air Gap Membrane distillation (AGMD) is a thermally driven separation process capable of treating challenging water types, but its low productivity is a major drawback. Membrane fouling is a common problem in many membrane treatment systems, which exacerbates AGMD's low overall productivity. In this study, we investigated the direct application of low-power ultrasound (8-23 W), as an in-line cleaning and performance boosting technique for AGMD. Two different highly saline feedwaters, namely natural groundwater (3970 μS/cm) and RO reject stream water (12760 μS/cm) were treated using Polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) membranes. Theoretical calculations and experimental investigations are presented, showing that the applied ultrasonic power range only produced acoustic streaming effects that enhanced cleaning and mass transfer. Attenuated Total Reflection Fourier-Transform Infrared Spectroscopy (ATR FT-IR) analysis showed that ultrasound was capable of effectively removing silica and calcium scaling. Ultrasound application on a fouled membrane resulted in a 100% increase in the permeate flux. Cleaning effects accounted for around 30-50% of this increase and the remainder was attributed to mass transfer improvements. Contaminant rejection percentages were consistently high for all treatments (>99%), indicating that ultrasound did not deteriorate the membrane structure. Scanning Electron Microscopy (SEM) analysis of the membrane surface was used to confirm this observation. The images of the membrane surface demonstrated that ultrasound successfully cleaned the previously fouled membrane, with no signs of structural damage. The results of this study highlight the efficient and effective application of direct low power ultrasound for improving AGMD performance.

Porous SiO2 coated AlxFeyZr1-x-yO2 solid superacid nanoparticles with negative charge for polyvinylidene fluoride (PVDF) membrane: Cleaning and partial desalinating seawater

In this work, porous SiO₂ coated Al_xFe_yZr_1-x-yO₂ solid superacid nanoparticles with negative charge (CS-SAFZr) were synthesized via hydrolysis, sulfation and sulfonation, and characterized by SEM, TEM, XRD, BET and so on. The results show that the size of CS-SAFZr nanoparticles prepared under the optimum preparation conditions is around 80 nm, thickness of the porous SiO₂ shell is about 20 nm, Hammett acidity is -16.197 and ion exchange capacity (IEC) is 0.98 mmol·g^-1. Correspondingly, ferrum (Fe) and aluminum (Al) elements are successfully doped into the ZrO₂ lattice and the doped nanoparticles present a specific surface area of 396.2 m² g^-1 with abundant hydroxyl and sulfonic acid groups on the surface. To investigate the properties of the nanoparticles as the filler, polyvinylidene fluoride (PVDF) was used as a candidate to prepare CS-SAFZr/PVDF ultrafiltration (UF) composite membranes and the performance were characterized via cleaning and desalinating seawater. Results indicate that the CS-SAFZr nanoparticles strengthen their compatibility with the membrane via hydrogen bonds and improve performances of PVDF membrane. The suspended solid and conductivity decline ratio of permeate seawater was 1.8 mg L^-1 and 13.20% respectively, indicating that CS-SAFZr/PVDF membrane performs seawater cleaning and partial desalination. Therefore, CS-SAFZr nanoparticles can be a promising candidate to modify PVDF membrane for cleaning and desalinating seawater.

Fouling-free ultrafiltration for humic acid removal

Membrane fouling is a serious concern that significantly affects the membrane filtration process. In this study, an ultrafiltration (UF) membrane was developed with surface auto-regeneration potential by immobilizing a photocatalyst [titanium dioxide nanoparticles (TiO₂ NPs)] on a hybrid polyvinylidene fluoride (PVDF) membrane to reduce fouling. The combination of photocatalysis and UF, namely, photocatalytic UF, induced the surface auto-regeneration potential to the membrane. The photocatalytic process was initiated after UV light reached the TiO₂ NPs through a quartz window in the membrane containing cell. The membrane, with an optimized distribution of TiO₂ NPs (3.04 g m⁻²), could completely regenerate itself during photocatalytic UF [with 2 mg L⁻¹ humic acid (HA)] without experiencing membrane fouling during 90 min of filtration. The impact of temperature, an important factor for increasing the kinetic rate of the photocatalyst, was also studied. The results showed that an increase in temperature did not affect the photocatalytic process, but increased the permeate flux, which was attributed to the decrease in kinematic viscosity of the water. Finally, four consecutive photocatalytic UF cycles demonstrated the stability of the membrane for a fouling-free UF process.

Membrane fouling is a serious concern that significantly affects the membrane filtration process.

Naphthenic acids removal from high TDS produced water by persulfate mediated iron oxide functionalized catalytic membrane, and by nanofiltration

Oil industries generate large amounts of produced water containing organic contaminants, such as naphthenic acids (NA) and very high concentrations of inorganic salts. Recovery of potable water from produced water can be highly energy intensive is some cases due to its high salt concentration, and safe discharge is more suitable. Here, we explored catalytic properties of iron oxide (FexOy nanoparticles) functionalized membranes in oxidizing NA from water containing high concentrations of total dissolved solids (TDS) using persulfate as an oxidizing agent. Catalytic decomposition of persulfate by FexOy functionalized membranes followed pseudo-first order kinetics with an apparent activation energy of 18 Kcal/mol. FexOy functionalized membranes were capable of lowering the NA concentrations to less than discharge limits of 10 ppm at 40 °C. Oxidation state of iron during reaction was quantified. Membrane performance was investigated for extended period of time. A coupled process of advanced oxidation catalyzed by membrane and nanofiltration was also evaluated. Commercially available nanofiltration membranes were found capable of retaining NA from water containing high concentrations of dissolved salts. Commercial NF membranes, Dow NF270 (Dow), and NF8 (Nanostone) had NA rejection of 79% and 82%, respectively. Retentate for the nanofiltration was further treated with advanced oxidation catalyzed by FexOy functionalized membrane for removal of NA.

Heteroatoms doped metal iron-polyvinylidene fluoride (PVDF) membrane for enhancing oxidation of organic contaminants

Iron nanoparticles (NPs) embedded in S, N-codoped carbon were prepared by one-step pyrolysis of a homogeneous mixture consisting of Fe, S, N, C precursors, and then immobilized in poly (vinylidene fluoride) membranes as a multifunctional catalytic system (NSC-Fe@PVDF) to effectively activate peroxymonosulfate (PMS) and oxidize organic compounds in water. The NSC-Fe@PVDF membranes effectively decolorized organic pollutants at a wide pH range (2.05-10.85), due to the synergistic effects between the S, N-doped carbon and iron NPs. The efficiency depended on the doping types, amount of metal, PMS dosages, reaction temperatures, solution pHs, and organic substrates. In-situ electron spin resonance spectroscopy and sacrificial-reagent incorporated catalysis indicate radical intermediates such as sulfate and hydroxyl radicals are mainly responsible for this persulfate-driven oxidation of organic compounds. Membrane's porous structure and high internal surface area not only minimize the NPs agglomeration, but also allow the facile transport of catalytic reactants to the active surface of metal catalysts. The results demonstrate the morphological and structural features of catalytic membranes enhance the overall catalytic activity.