Influence of controlled functionalization of mesoporous silica nanoparticles as tailored fillers for thin-film nanocomposite membranes on desalination performance

Mechanism of wetting by anionic surfactants with different polar groups on hydrophilic and hydrophobic nano-silica

CONTEXT

With advancing technology, the hazards of hydrophilic and hydrophobic nano-silica dust have become increasingly apparent. Surfactants are widely used in dust control; however, their performance is primarily determined by their polar groups. To investigate the effect of various polar groups of anionic surfactants on the wettability of hydrophilic and hydrophobic nanosilica. The results indicate that the electronegativity of the electrostatic potential on the hydroxylated silica surface is relatively strong, the larger the electrostatic potential difference (ΔESP) between the surface binding sites and the polar groups of the surfactant, the less favorable the surface is for hydrophobic modification. Additionally, C and O atoms tend to form smaller negative electrostatic potentials compared to S and O atoms, with polar group activity ranked as carboxylate > sulfonate > benzene sulfonate > sulfate. The interaction between SiO2-OH surfaces and water molecules is approximately 3.4 times stronger than that of SiO2-CH3 surfaces. The interaction between water molecules and the SiO2-OH surface is primarily governed by van der Waals forces, whereas the interaction between water molecules and the SiO2-CH3 surface is mainly driven by electrostatic forces. The polar groups of the surfactant are distributed in the aqueous phase, while the nonpolar groups interact with the surface through electrostatic interactions. The hydration layer surrounding the polar groups of hydrophilic surfaces is primarily stabilized by strong hydrogen bonding with water molecules. In contrast, for hydrophobic nano-silica surfaces, the hydration layer is influenced by both van der Waals forces and weaker hydrogen bonding interactions. The SiO2-CH3 surface cannot form hydrogen bonds, while the SiO2-OH surface has a strong capacity to stably form hydrogen bonds with carboxylate and sulfate groups. Hydrogen bonding is an essential factor in wetting. The polar group COO- is suitable for controlling hydrophilic and hydrophobic nano-silica dust. These findings provide theoretical and technical references for the selection, application, and design of surfactants in nano-silica dust control.

METHODS

To elucidate the effects of various polar groups of anionic surfactants on the wetting of hydrophilic and hydrophobic nano-silica, quantum chemical calculations and molecular dynamics simulations were used to investigate the interfacial adsorption and wetting behavior of anionic surfactants with identical chain lengths but different polar groups on these surfaces.

Mesoporous Silica Nanotraps for Mitigating Bleeding Risk From 'Irreversible' Antiplatelet Drugs

The severe bleeding complications of long-term antiplatelet therapy limit its broader application in the treatment or prevention of thrombosis-associated diseases. This risk is particularly serious when facing emergency surgeries where rapid restoration of normal platelet function is required. Timely reversal of the effects of antiplatelet agents becomes crucial in such scenarios. Despite the widespread use of clopidogrel and prasugrel for their potent antiplatelet activity, the absence of specific and effective reversal agents remains a notable challenge. The pharmacological activity of clopidogrel and prasugrel is mediated by sulfhydryl-containing active metabolites, which form disulfide bonds with P2Y12 receptors on the surface of platelets to inhibit their aggregation. Taking advantage of this action mechanism of these "irreversible" antiplatelet drugs, click chemistry-functionalized mesoporous silica (SiO2-Mal) nanotraps are fabricated to capture the antiplatelet drugs' active metabolites and restore hemostasis. Subsequently, a comprehensive assessment of the effectiveness and safety of the SiO2-Mal nanotraps is conducted using mouse, rabbit, and pig animal models, highlighting their potential application as a functional reversal agent for clinically relevant thienopyridine antiplatelet drugs, believed until now to be irreversible in their inhibition of platelet activity.

Ordered Mesoporous Electrodes for Sensing Applications

Electrochemical sensors have become increasingly relevant in fields such as medicine, environmental monitoring, and industrial process control. Selectivity, specificity, sensitivity, signal reproducibility, and robustness are among the most important challenges for their development, especially when the target compound is present in low concentrations or in complex analytical matrices. In this context, electrode modification with Mesoporous Thin Films (MTFs) has aroused great interest in the past years. MTFs present high surface area, uniform pore distribution, and tunable pore size. Furthermore, they offer a wide variety of electrochemical signal modulation possibilities through molecular sieving, electrostatic or steric exclusion, and preconcentration effects which are due to mesopore confinement and surface functionalization. In order to fully exploit these advantages, it is central to develop reproducible routes for sensitive, selective, and robust MTF-modified electrodes. In addition, it is necessary to understand the complex mass and charge transport processes that take place through the film (particularly in the mesopores, pore surfaces, and interfaces) and on the electrode in order to design future intelligent and adaptive sensors. We present here an overview of MTFs applied to electrochemical sensing, in which we address their fabrication methods and the transport processes that are critical to the electrode response. We also summarize the current applications in biosensing and electroanalysis, as well as the challenges and opportunities brought by integrating MTF synthesis with electrode microfabrication, which is critical when moving from laboratory work to in situ sensing in the field of interest.

Ultrasound-assisted synthesis of MSNs/PS nanocomposite membranes for effective removal of Cd2+ and Pb2+ ions from aqueous solutions

Contamination of heavy metal (Cd²⁺ & Pb²⁺) ions in drinking water is producing major impacts on the environment and public health and is considered one of the greatest dangers to humanity. Membrane technology has been chosen over other processing methods due to its simplicity and high capacity for more effective removal of hazardous heavy metals. In the current study, amine, thiol, and bi-thiol functional groups were used to functionalize mesoporous silica nanoparticles (MSNs) to improve the efficiency of the silica nanoparticle. The morphology of the MSNs as well as the existence of amine and thiol on the surface of MSNs was demonstrated by a variety of characterization techniques, including FTIR, TEM, and SEM examination. The impact of surface-modified MSNs on the morphology, properties, and performance of polysulfone (PS) nanofiltration (NF) membranes was also evaluated. The membrane that incorporated amine with thiol-based MSNs (DiMP-MSNs/PS-NF membrane) had the highest pure water permeability (6.7 LMH bar^-1). As a result of the functional groups, the surface-modified MSNs/PS nanofiltration are extremely effective at removing heavy metal ions from aqueous solutions. The surface-modified MSNs/PS nano-filtration membranes exhibit unprecedented Cd²⁺ and Pb²⁺ removal rates of approximately 82% and 99%, respectively. This research indicates the possible application of the surface-modified MSNs/PS nanofiltration membrane as a promising platform to remove heavy metal ions from polluted water.

ZnO/PDA/Mesoporous Cellular Foam Functionalized Thin-Film Nanocomposite Membrane towards Enhanced Nanofiltration Performance

Thin-film nanocomposite (TFN) membranes are the third-generation membranes being explored for nanofiltration applications. Incorporating nanofillers in the dense selective polyamide (PA) layer improves the permeability-selectivity trade-off. The mesoporous cellular foam composite Zn-PDA-MCF-5 was used as a hydrophilic filler in this study to prepare TFN membranes. Incorporating the nanomaterial onto the TFN-2 membrane resulted in a decrease in the water contact angle and suppression of the membrane surface roughness. The pure water permeability of 6.40 LMH bar^-1 at the optimal loading ratio of 0.25 wt.% obtained was higher than the TFN-0 (4.20 LMH bar^-1). The optimal TFN-2 demonstrated a high rejection of small-sized organics (>95% rejection for 2,4-dichlorophenol over five cycles) and salts-Na₂SO₄ (≈95%) > MgCl₂ (≈88%) > NaCl (86%) through size sieving and Donnan exclusion mechanisms. Furthermore, the flux recovery ratio for TFN-2 increased from 78.9 to 94.2% when challenged with a model protein foulant (bovine serum albumin), indicating improved anti-fouling abilities. Overall, these findings provided a concrete step forward in fabricating TFN membranes that are highly suitable for wastewater treatment and desalination applications.

pH and pCl Operational Parameters in Some Metallic Ions Separation with Composite Chitosan/Sulfonated Polyether Ether Ketone/Polypropylene Hollow Fibers Membranes

The development of new composite membranes is required to separate chemical species from aggressive environments without using corrective reagents. One such case is represented by the high hydrochloric acid mixture (very low pH and pCl) that contains mixed metal ions, or that of copper, cadmium, zinc and lead ions in a binary mixture (Cu-Zn and Cd-Pb) or quaternary mixture. This paper presents the obtaining of a composite membrane chitosan (Chi)-sulfonated poly (ether ether ketone) (sPEEK)-polypropylene hollow fiber (Chi/sPEEK/PPHF) and its use in the separation of binary or quaternary mixtures of copper, cadmium, zinc, and lead ions by nanofiltration and pertraction. The obtained membranes were morphologically and structurally characterized using scanning electron microscopy (SEM), high resolution SEM (HR-SEM), energy dispersive spectroscopy analysis (EDAX), Fourier Transform InfraRed (FTIR) spectroscopy, thermogravimetric analysis, and differential scanning calorimetry (TGA-DSC), but also used in preliminary separation tests. Using the ion solutions in hydrochloric acid 3 mol/L, the separation of copper and zinc or cadmium and lead ions from binary mixtures was performed. The pertraction results were superior to those obtained by nanofiltration, both in terms of extraction efficiency and because at pertraction, the separate cation was simultaneously concentrated by an order of magnitude. The mixture of the four cations was separated by nanofiltration (at 5 bars, using a membrane of a 1 m² active area) by varying two operational parameters: pH and pCl. Cation retention could reach 95% when adequate values of operational parameters were selected. The paper makes some recommendations for the use of composite membranes, chitosan (Chi)-sulfonated poly (ether ether ketone) (sPEEK)-polypropylene hollow fiber (Chi/sPEEK/PPHF), so as to obtain the maximum possible retention of the target cation.

Osmium Recovery as Membrane Nanomaterials through 10-Undecenoic Acid Reduction Method

The recovery of osmium from residual osmium tetroxide (OsO₄) is a necessity imposed by its high toxicity, but also by the technical-economic value of metallic osmium. An elegant and extremely useful method is the recovery of osmium as a membrane catalytic material, in the form of nanoparticles obtained on a polymeric support. The subject of the present study is the realization of a composite membrane in which the polymeric matrix is the polypropylene hollow fiber, and the active component consists of the osmium nanoparticles obtained by reducing an alcoholic solution of osmium tetroxides directly on the polymeric support. The method of reducing osmium tetroxide on the polymeric support is based on the use of 10-undecenoic acid (10-undecylenic acid) (UDA) as a reducing agent. The osmium tetroxide was solubilized in t-butanol and the reducing agent, 10-undecenoic acid (UDA), in i-propanol, t-butanol or n-decanol solution. The membranes containing osmium nanoparticles (Os-NP) were characterized morphologically by the following: scanning electron microscopy (SEM), high-resolution SEM (HR-SEM), structurally: energy-dispersive spectroscopy analysis (EDAX), Fourier transform infrared (FTIR) spectroscopy. In terms of process performance, thermal gravimetric analysis was performed by differential scanning calorimetry (TGA, DSC) and in a redox reaction of an organic marker, p-nitrophenol (PNP) to p-aminophenol (PAP). The catalytic reduction reaction with sodium tetraborate solution of PNP to PAP yielded a constant catalytic rate between 2.04 × 10^-4 mmol s^-1 and 8.05 × 10^-4 mmol s^-1.

Fabrication of Polysulfone-Surface Functionalized Mesoporous Silica Nanocomposite Membranes for Removal of Heavy Metal Ions from Wastewater

Membranes are an efficient way to treat emulsified heavy metal-based wastewater, but they generally come with a trade-off between permeability and selectivity. In this research, the amine and sulphonic groups on the inner and outer surface of mesoporous silica nanoparticles (MSNs) were first modified by a chemical approach. Then, MSNs with amine and sulphonic groups were utilized as new inorganic nanofiller to fabricate mixed matrix polysulfone (PSU) nanocomposite membranes using the classical phase inversion approach. The resultant nanoparticles and membranes were characterized by their physico-chemical characteristics as well as determination of pure water permeability along with cadmium and zinc ion removal. Embedding nanoparticles resulted in a significant rise in the water permeability as a result of changes in the surface properties and porosity of the membrane. Furthermore, the efficiency of developed membranes to remove cadmium and zinc was significantly improved by more than 90% due to the presence of functional groups on nanoparticles. The functionalized-MSNs/PSU nanocomposite membrane has the potential to be an effective industrial effluent removal membrane.

Osmium Nanoparticles-Polypropylene Hollow Fiber Membranes Applied in Redox Processes

Composite membranes play a very important role in the separation, concentration, and purification processes, but especially in membrane reactors and membrane bioreactors. The development of composite membranes has gained momentum especially through the involvement of various nanoparticles, polymeric, oxide, or metal, that have contributed to increasing their reactivity and selectivity. This paper presents the preparation and characterization of an active metal nanoparticle-support polymer type composite membrane, based on osmium nanoparticles obtained in situ on a polypropylene hollow fiber membrane. Osmium nanoparticles are generated from a solution of osmium tetroxide in tert-butyl alcohol by reduction with molecular hydrogen in a contactor with a polypropylene membrane. The composite osmium-polypropylene hollow fiber obtained membranes (Os-PPM) were characterized from the morphological and structural points of view: scanning electron microscopy (SEM), high resolution SEM (HR-SEM), energy dispersive spectroscopy analysis (EDAX), X-ray diffraction analysis (XRD), Fourier transform Infrared (FTIR) spectroscopy, thermal gravimetric analysis, and differential scanning calorimetry (TGA, DSC). The process performance was tested in a redox process of p-nitrophenol and 10-undecylenic (10-undecenoic) acid, as a target substance of biological or biomedical interest, in solutions of lower aliphatic alcohols in a membrane contactor with a prepared composite membrane. The characteristics of osmium nanoparticles-polypropylene hollow fiber membranes open the way to biological and biotechnological applications. These membranes do not contaminate the working environment, operate at relatively low temperatures, provide a large contact area between reactants, allow successive oxidation and reduction operations in the same module, and help to recover the reaction mass by ultrafiltration. The results obtained show that the osmium-polypropylene composite membrane allows the reduction of p-nitrophenol or the oxidation of 10-undecylenic acid, the conversion depending on the concentration in the lower aliphatic alcohol, the nature of the lower aliphatic alcohol, and the oxidant or reducing flow through the membrane contactor.

Improving the Performance of Composite Hollow Fiber Membranes with Magnetic Field Generated Convection Application on pH Correction

The membranes and membrane processes have succeeded in the transition from major technological and biomedical applications to domestic applications: water recycling in washing machines, recycling of used cooking oil, recovery of gasoline vapors in the pumping stations or enrichment of air with oxygen. In this paper, the neutralization of condensation water and the retention of aluminum from thermal power plants is studied using ethylene propylene diene monomer sulfonated (EPDM-S) membranes containing magnetic particles impregnated in a microporous propylene hollow fiber (I-PPM) matrix. The obtained membranes were characterized from the morphological and structural points of view, using scanning electron microscopy (SEM), high resolution SEM (HR-SEM), energy dispersive spectroscopy analysis (EDAX) and thermal gravimetric analyzer. The process performances (flow, selectivity) were studied using a variable magnetic field generated by electric coils. The results show the possibility of correcting the pH and removing aluminum ions from the condensation water of heating plants, during a winter period, without the intervention of any operator for the maintenance of the process. The pH was raised from an acidic one (2–4), to a slightly basic one (8–8.5), and the concentration of aluminum ions was lowered to the level allowed for discharge. Magnetic convection of the permeation module improves the pH correction process, but especially prevents the deposition of aluminum hydroxide on hollow fibers membranes.

Accessible Silver-Iron Oxide Nanoparticles as a Nanomaterial for Supported Liquid Membranes

The present study introduces the process performances of nitrophenols pertraction using new liquid supported membranes under the action of a magnetic field. The membrane system is based on the dispersion of silver–iron oxide nanoparticles in n-alcohols supported on hollow microporous polypropylene fibers. The iron oxide–silver nanoparticles are obtained directly through cyclic voltammetry electrolysis run in the presence of soluble silver complexes ([AgCl₂]⁻; [Ag(S₂O₃)₂]³⁻; [Ag(NH₃)₂]⁺) and using pure iron electrodes. The nanostructured particles are characterized morphologically and structurally by scanning electron microscopy (SEM and HFSEM), EDAX, XRD, and thermal analysis (TG, DSC). The performances of the nitrophenols permeation process are investigated in a variable magnetic field. These studies show that the flux and extraction efficiency have the highest values for the membrane system embedding iron oxide–silver nanoparticles obtained electrochemically in the presence of [Ag(NH₃)₂]⁺ electrolyte. It is demonstrated that the total flow of nitrophenols through the new membrane system depends on diffusion, convection, and silver-assisted transport.

Modifying thin film composite membrane with zeolitic imidazolate framework-8@polydopamine for enhanced antifouling property

Biofouling and organic fouling are major obstacles for polymeric membranes during application. In this work, zeolitic imidazolate framework-8@polydopamine (ZIF-8@PDA) nanoparticles were prepared by an aqueous synthesis strategy and incorporated into the polyamide (PA) selective layer to synthesize thin film nanocomposite membrane (TFN) during interfacial polymerization. The permeability and selectivity of the composite membrane were simultaneously improved with the introduction of ZIF-8@PDA. The water permeability of the TFN membrane increased to 3.74 ± 0.19 L/(m2·h·bar), which is 43.8% higher than that of the control membrane. Besides, the rejection of TFN membrane to sodium chloride is 98.68 ± 0.13%, which shows 0.99% increment than the unmodified membrane. Moreover, organic fouling and biofouling of the TFN membrane were also alleviated thanks to the introduction of the hydrophilic ZIF-8@PDA. The short-term filtration results indicate the performance of the TFN membrane is stable during operation.

Preparation of a novel zwitterionic striped surface thin-film composite nanofiltration membrane with excellent salt separation performance and antifouling property

Thin-film composite (TFC) nanofiltration (NF) membranes were fabricated via the co-deposition of taurine, tannic acid (TA), and polyethyleneimine (PEI), followed by subsequent interfacial polymerization with trimesoyl chloride (TMC) on the surface of the polysulfone ultrafiltration substrates. The surface properties, including the roughness, hydrophilicity, surface potential, and NF performances were facilely tuned by varying the taurine content for the prepared TFC membranes. In addition, the as-prepared TFC NF membranes had an excellent antifouling property and flux recovery ratio (FRR) in humic acid (HA), bovine serum albumin (BSA) and sodium alginate (SA) filtration tests. These results also revealed that the taurine content controlled the formation of the striped surface. Thus, this work provided a viable strategy for fabricating TFC NF membranes with high selectivity and outstanding antifouling ability.

Thin-film composite (TFC) nanofiltration (NF) membranes with zwitterionic striped surface were fabricated via the co-deposition and interfacial polymerization.

Porous Zr-Based Metal-Organic Frameworks (Zr-MOFs)-Incorporated Thin-Film Nanocomposite Membrane toward Enhanced Desalination Performance

Four different thin-film nanocomposite (TFN) membranes were prepared by adding different concentrations of porous Zr-metal-organic frameworks (MOFs) (UiO-66 and UiO-66-NH₂) to piperazine aqueous solution (aqueous phase) or 1,3,5-benzenetricarbonyl trichloride-n-hexane solution (organic phase) by interfacial polymerization. The main purpose is to study the specific effects of different addition methods and addition amounts of nanoparticles on the structure and performance of the TFN membranes by interfacial polymerization. All four TFN membranes exhibited a higher water permeability while maintaining high salt rejection compared to thin-film composite membrane. On the one hand, the TFN membranes behave differently, which are prepared by adding the same kind of nanoparticles to the aqueous phase or organic phase, respectively. The TFN membrane prepared by adding 0.2 w/v% UiO-66 to the organic phase had a high water flux of 87.86 L m^-2 h^-1, compared to 46.31 L m^-2 h^-1 of the membrane prepared by adding 0.3 w/v% UiO-66 in the aqueous phase. This is due to the fact that UiO-66 greatly slows the interfacial polymerization rate when UiO-66 is added to the organic phase, resulting in a thinner and wider-aperture polyamide thin-film layer, reducing the water transmission resistance during filtration. Therefore, it is more economical by adding nanoparticles to organic phase than aqueous phase under the same filtering effect. On the other hand, different nanoparticles can also cause differences in performance and structure of the TFN membranes even in the same preparation manner. TFN membrane with UiO-66-NH₂ in the aqueous phase has higher water permeance than the one with UiO-66 in the aqueous phase, owing to the good hydrophilicity of the amino group, which improves the water dispersibility of UiO-66-NH₂ so that the TFN membrane is more uniform. In addition, UiO-66-NH₂ slows down the process of interface polymerization, making the membrane more porous. The monomers in the aqueous phase and organic phase can be adsorbed in the pores of Zr-MOFs, which makes the interfacial polymerization occur both in the pores and on the surface of the pores. Thus, the compatibility between the polyamide and MOFs was enhanced and less defects were formed in the thin-film layer, resulting in a high salt rejection even when the concentration of Zr-MOFs increased. This is the first time to explain that polyamide membrane has not obvious salt rejection attenuation with increasing porous material content using pore adsorption reaction monomer principle. Also, the Zr-MOFs-based TFN membrane exhibited good heat resistance and antifouling property. This work shows that porous Zr-MOFs nanomaterials have significant advantages in the development of nanofiltration membranes with high water flux and rejection.

Metal Organic Framework Based Polymer Mixed Matrix Membranes: Review on Applications in Water Purification

Polymeric membranes have been widely employed for water purification applications. However, the trade-off issue between the selectivity and permeability has limited its use in various applications. Mixed matrix membranes (MMMs) were introduced to overcome this limitation and to enhance the properties and performance of polymeric membranes by incorporation of fillers such as silica and zeolites. Metal-organic frameworks (MOFs) are a new class of hybrid inorganic-organic materials that are introduced as novel fillers for incorporation in polymeric matrix to form composite membranes for different applications especially water desalination. A major advantage of MOFs over other inorganic fillers is the possibility of preparing different structures with different pore sizes and functionalities, which are designed especially for a targeted application. Different MMMs fabrication techniques have also been investigated to fabricate MMMs with pronounced properties for a specific application. Synthesis techniques include blending, layer-by-layer (LBL), gelatin-assisted seed growth and in situ growth that proved to give the most homogenous dispersion of MOFs within the organic matrix. It was found that the ideal filler loading of MOFs in different polymeric matrices is 10%, increasing the filler loading beyond this value led to formation of aggregates that significantly decreased the MOFs-MMMs performance. Despite the many merits of MOFs-MMMs, the main challenge facing the upscaling and wide commercial application of MOFs-MMMs is the difficult synthesis conditions of the MOFs itself and the stability and sustainability of MOFs-MMMs performance. Investigation of new MOFs and MOFs-MMMs synthesis techniques should be carried out for further industrial applications. Among these new synthesis methods, green MOFs synthesis has been highlighted as low cost, renewable, environmentally friendly and recyclable starting materials for MOFs-MMMs. This paper will focus on the investigation of the effect of different recently introduced MOFs on the performance of MOFs-MMMs in water purification applications.

Cell adherence and drug delivery from particle based mesoporous silica films

Spatially and temporally controlled drug delivery is important for implant and tissue engineering applications, as the efficacy and bioavailability of the drug can be enhanced, and can also allow for drugging stem cells at different stages of development. Long-term drug delivery over weeks to months is however difficult to achieve, and coating of 3D surfaces or creating patterned surfaces is a challenge using coating techniques like spin- and dip-coating. In this study, mesoporous films consisting of SBA-15 particles grown onto silicon wafers using wet processing were evaluated as a scaffold for drug delivery. Films with various particle sizes (100–900 nm) and hence thicknesses were grown onto trichloro(octadecyl)silane-functionalized silicon wafers using a direct growth method. Precise patterning of the areas for film growth could be obtained by local removal of the OTS functionalization through laser ablation. The films were incubated with the drug model 3,3′-dioctadecyloxacarbocyanine perchlorate (DiO), and murine myoblast cells (C2C12 cells) were seeded onto films with different particle sizes. Confocal laser scanning microscopy (CLSM) was used to study the cell growth, and a vinculin-mediated adherence of C2C12 cells on all films was verified. The successful loading of DiO into the films was confirmed by UV-vis and CLSM. It was observed that the drugs did not desorb from the particles during 24 hours in cell culture. During adherent growth on the films for 4 h, small amounts of DiO and separate particles were observed inside single cells. After 24 h, a larger number of particles and a strong DiO signal were recorded in the cells, indicating a particle mediated drug uptake. The vast majority of the DiO-loaded particles remained attached to the substrate also after 24 h of incubation, making the films attractive as longer-term reservoirs for drugs on e.g. medical implants.

Particle-based mesoporous silica films synthesized through a direct growth method were successfully used as a drug delivery system.