Surface modification of polyvinylidene fluoride membrane by atom-transfer radical-polymerization of quaternary ammonium compound for mitigating biofouling

Swollen hydrogels with strong mechanical characteristics: A superior adsorbent for the sustainable removal of diclofenac sodium

Hydrogel adsorbents that possess both good mechanical strength and adsorption capabilities are crucial for practical wastewater treatment. However, achieving this balance has been demanding due to the trade-off between swelling properties and adsorption capacities in hydrogels. Although swelling increases the availability of functional groups and facilitates the diffusion of pollutants, it compromises the mechanical integrity. In this study, we address this challenge by developing double-network hydrogels based on poly(vinyl) alcohol and poly[2-(acryloyloxy)ethyl]trimethyl ammonium chloride, prepared via free-radical polymerization, and subsequent freeze-thaw treatment. These hydrogels were investigated for their efficacy in removing diclofenac sodium, a prevalent drug pollutant in pharmaceutical wastewater. By leveraging the synergistic effect of the physical and chemical networks, the prepared hydrogels exhibit intrinsic toughness and compressibility even in a fully swollen state. Most importantly, the maximum adsorption capacity yielded by the Langmuir model fitting was 1012 mg/g under natural conditions, they surpass all other hydrogel adsorbents proposed so far. Thermodynamic analysis implied the spontaneous and exothermic nature of diclofenac sodium adsorption process, while infrared and photoemission spectroscopy revealed that diclofenac sodium uptake is predominantly governed by ion exchange. Overall, double-network hydrogels offer considerable promise for eco-friendly and sustainable wastewater purification due to their high mechanical stability, outstanding adsorption performance, good reusability, and adaptability to diverse environmental conditions.

High-Performance Nanofiltration Membrane with Dual Resistance to Gypsum Scaling and Biofouling for Enhanced Water Purification

Nanofiltration (NF) technology is pivotal for ensuring a sustainable and reliable supply of clean water. To address the critical need for advanced thin-film composite (TFC) polyamide (PA) membranes with exceptional permselectivity and fouling resistance for emerging contaminant purification, we introduce a novel high-performance NF membrane. This membrane features a selective polypiperazine (PIP) layer functionalized with amino-containing quaternary ammonium compounds (QACs) through an in situ interfacial polycondensation reaction. Our investigation demonstrated that precise QAC functionalization enabled the construction of the selective PA layer with increased surface area, enhanced microporosity, stronger electronegativity, and reduced thickness compared to the control PIP membrane. As a result, the QAC NF membrane exhibited an approximately 51% increase in water permeance compared to the control PIP membrane, while achieving superior retention capabilities for divalent salts (>99%) and emerging organic contaminants (>90%). Furthermore, the incorporation of QACs into the PIP selective layer was proved to be effective in mitigating mineral scaling by allowing selective passage of scale-forming cations, while simultaneously exhibiting strong antimicrobial properties to combat biofouling. The in situ QAC incorporation strategy presented in this study provides valuable guidelines for the fit-for-purpose design of the selective PA layer, which is crucial for the development of high-performance NF membranes for efficient water purification.

Cetyltrimethylammonium-chloride assisted in situ metabolic incorporation of nano-sized ROS-generating cascade-reaction containers in Gram-positive and Gram-negative peptidoglycan layers for the control of bacterially-induced sepsis

Cascade-reaction containers generating reactive oxygen species (ROS) as an alternative for antibiotic-based strategies for bacterial infection control, require endogenous oxygen-sources and ROS-generation close to or preferably inside target bacteria. Here, this is achieved by cetyltrimethylammonium-chloride (CTAC) assisted in situ metabolic labeling and incorporation of mesoporous SiO2-nanoparticles, dual-loaded with glucose-oxidase and Fe3O4-nanoparticles as cascade-reaction containers, inside bacterial cell walls. First, azide-functionalized d-alanine (D-Ala-N3) was inserted in cell wall peptidoglycan layers of growing Gram-positive pathogens. In Gram-negatives, this could only be achieved after outer lipid-membrane permeabilization, using a low concentration of CTAC. Low concentrations of CTAC had no adverse effect on in vitro blood clotting or hemolysis nor on the health of mice when blood-injected. Next, dibenzocyclooctyne-polyethylene-glycol modified, SiO2-nanoparticles were in situ click-reacted with d-Ala-N3 in bacterial cell wall peptidoglycan layers. Herewith, a two-step cascade-reaction is facilitated inside bacteria, in which glucose-oxidase generates H2O2 at endogenously-available glucose concentrations, while subsequently Fe3O4-nanoparticles catalyze generation of •OH from the H2O2 generated. Generation of •OH inside bacterial cell walls by dual-loaded mesoporous SiO2-nanoparticles yielded more effective in vitro killing of both planktonic Gram-positive and Gram-negative bacteria suspended in 10 % plasma than SiO2-nanoparticles solely loaded with glucose-oxidase. Gram-positive or Gram-negative bacterially induced sepsis in mice could be effectively treated by in situ pre-treatment with tail-vein injected CTAC and d-Ala-N3, followed by injection of dual-loaded cascade-reaction containers without using antibiotics. This makes in situ metabolic incorporation of cascade-reaction containers as described attractive for further investigation with respect to the control of other types of infections comprising planktonic bacteria. STATEMENT OF SIGNIFICANCE: In situ metabolic-incorporation of cascade-reaction-containers loaded with glucose-oxidase and Fe3O4 nanoparticles into bacterial cell-wall peptidoglycan is described, yielding ROS-generation from endogenous glucose, non-antibiotically killing bacteria before ROS inactivates. Hitherto, only Gram-positives could be metabolically-labeled, because Gram-negatives possess two lipid-membranes. The outer membrane impedes direct access to the peptidoglycan. This problem was solved by outer-membrane permeabilization using a quaternary-ammonium compound. Several studies on metabolic-labeling perform crucial labeling steps during bacterial-culturing that in real-life should be part of a treatment. In situ metabolic-incorporation as described, can be applied in well-plates during in vitro experiments or in the body as during in vivo animal experiments. Surprisingly, metabolic-incorporation proceeded unhampered in blood and a murine, bacterially-induced sepsis could be well treated.

Design, preparation, and characterization of lubricating polymer brushes for biomedical applications

The lubrication modification of biomedical devices significantly enhances the functionality of implanted interventional medical devices, thereby providing additional benefits for patients. Polymer brush coating provides a convenient and efficient method for surface modification while ensuring the preservation of the substrate's original properties. The current research has focused on a "trial and error" method to finding polymer brushes with superior lubricity qualities, which is time-consuming and expensive, as obtaining effective and long-lasting lubricity properties for polymer brushes is difficult. This review summarizes recent research advances in the biomedical field in the design, material selection, preparation, and characterization of lubricating and antifouling polymer brushes, which follow the polymer brush development process. This review begins by examining various approaches to polymer brush design, including molecular dynamics simulation and machine learning, from the fundamentals of polymer brush lubrication. Recent advancements in polymer brush design are then synthesized and potential avenues for future research are explored. Emphasis is placed on the burgeoning field of zwitterionic polymer brushes, and highlighting the broad prospects of supramolecular polymer brushes based on host-guest interactions in the field of self-repairing polymer brush applications. The review culminates by providing a summary of methodologies for characterizing the structural and functional attributes of polymer brushes. It is believed that a development approach for polymer brushes based on "design-material selection-preparation-characterization" can be created, easing the challenge of creating polymer brushes with high-performance lubricating qualities and enabling the on-demand creation of coatings. STATEMENT OF SIGNIFICANCE: Biomedical devices have severe lubrication modification needs, and surface lubrication modification by polymer brush coating is currently the most promising means. However, the design and preparation of polymer brushes often involves "iterative testing" to find polymer brushes with excellent lubrication properties, which is both time-consuming and expensive. This review proposes a polymer brush development process based on the "design-material selection-preparation-characterization" strategy and summarizes recent research advances and trends in the design, material selection, preparation, and characterization of polymer brushes. This review will help polymer brush researchers by alleviating the challenges of creating polymer brushes with high-performance lubricity and promises to enable the on-demand construction of polymer brush lubrication coatings.

Modified polymer membranes for the removal of pharmaceutical active compounds in wastewater and its mechanism-A review

Membrane technology can play a suitable role in removing pharmaceutical active compounds since it requires low energy and simple operation. Even though membrane technology has progressed for wastewater applications nowadays, modifying membranes to achieve the strong desired membrane performance is still needed. Thus, this study overviews a comprehensive insight into the application of modified polymer membranes to remove pharmaceutical active compounds from wastewater. Biotoxicity of pharmaceutical active compounds is first prescribed to gain deep insight into how membranes can remove pharmaceutical active compounds from wastewater. Then, the behavior of the diffusion mechanism can be concisely determined using mass transfer factor model that represented by β and B with value up to 2.004 g h mg-1 and 1.833 mg g-1 for organic compounds including pharmaceutical active compounds. The model refers to the adsorption of solute to attach onto acceptor sites of the membrane surface, external mass transport of solute materials from the bulk liquid to the membrane surface, and internal mass transfer to diffuse a solute toward acceptor sites of the membrane surface with evidenced up to 0.999. Different pharmaceutical compounds have different solubility and relates to the membrane hydrophilicity properties and mechanisms. Ultimately, challenges and future recommendations have been presented to view the future need to enhance membrane performance regarding fouling mitigation and recovering compounds. Afterwards, the discussion of this study is projected to play a critical role in advance of better-quality membrane technologies for removing pharmaceutical active compounds from wastewater in an eco-friendly strategy and without damaging the ecosystem.

Current advances of nanocellulose application in biomedical field

Nanocellulose (NC) is a natural fiber that can be extracted in fibrils or crystals form from different natural sources, including plants, bacteria, and algae. In recent years, nanocellulose has emerged as a sustainable biomaterial for various medicinal applications including drug delivery systems, wound healing, tissue engineering, and antimicrobial treatment due to its biocompatibility, low cytotoxicity, and exceptional water holding capacity for cell immobilization. Many antimicrobial products can be produced due to the chemical functionality of nanocellulose, such disposable antibacterial smart masks for healthcare use. This article discusses comprehensively three types of nanocellulose: cellulose nanocrystals (CNC), cellulose nanofibrils (CNF), and bacterial nanocellulose (BNC) in view of their structural and functional properties, extraction methods, and the distinctive biomedical applications based on the recently published work. On top of that, the biosafety profile and the future perspectives of nanocellulose-based biomaterials have been further discussed in this review.

A facile and scalable strategy for constructing Janus cotton fabric with persistent antibacterial activity

Natural cotton fibers have attached considerable attention due to their excellent wearing comfort, breathability and warmth. However, it remains a challenge to devise a scalable and facile strategy to retrofit natural cotton fibers. Here, the cotton fiber surface was oxidized by sodium periodate with a mist process, then [2-(methacryloyloxy) ethyl] trimethylammonium chloride (DMC) was co-polymerized with hydroxyethyl acrylate (HA) to obtain an antibacterial cationic polymer (DMC-co-HA). The self-synthesized polymer was covalently grafted onto the aldehyde-functionalized cotton fibers via an acetal reaction between hydroxyl groups of the polymer and aldehyde groups of the oxidized cotton surface. Finally, the resulted Janus functionalized cotton fabric (JanCF) revealed robust and persistent antimicrobial activity. The antibacterial test showed that when the molar ratio of DMC/HA was 50: 1, JanCF possessed the best BR (bacterial reduction) values of 100 % against Escherichia coli and Staphylococcus aureus. Furthermore, the BR values could be maintained over 95 % even after the durability test. In addition, JanCF exhibited excellent antifungal activity against Candida albicans. The cytotoxicity assessment confirmed that JanCF exhibited a reliable safety effect on human skin. Particularly, the intrinsic outstanding characteristics (strength, flexibility, etc.) of the cotton fabric were not considerably deteriorated compared to the control samples.

Development of Antifouling Coatings Based on Quaternary Ammonium Compounds through a Multilayer Approach

The development of polymeric materials as antifouling coatings for aquaculture nets is elaborated in the present work. In this context, cross-linked polymeric systems based on quaternary ammonium compounds (immobilized or releasable) prepared under mild aqueous conditions were introduced as a more environmentally friendly methodology for coating nets on a large scale. To optimize the duration of action of the coatings, a multilayer coating method was applied by combining the antimicrobial organo-soluble copolymer poly(cetyltrimethylammonium 4-styrenesulfonate-co-glycidyl methacrylate) [P(SSAmC16-co-GMA20)] as the first layer with either the water-soluble copolymer poly(vinylbenzyl trimethylammonium chloride-co-acrylic acid) [P(VBCTMAM-co-AA20)] or the water-soluble polymers poly(acrylic acid) (PAA) and poly(hexamethylene guanidine), PHMG, as the second layer. The above-mentioned approach, followed by thermal cross-linking of the polymeric coatings, resulted in stable materials with controlled release of the biocidal species. The coated nets were studied in terms of their antifouling efficiency under accelerated biofouling conditions as well as under real conditions in an aquaculture field. Resistance to biofouling after three water-nutrient replenishments was observed under laboratory accelerated biofouling conditions. In addition, at the end of the field test (day 23) the uncoated nets were completely covered by marine contaminants, while the coated nets remained intact over most of their extent.

From Antibacterial to Antibiofilm Targeting: An Emerging Paradigm Shift in the Development of Quaternary Ammonium Compounds (QACs)

In a previous development stage, mostly individual antibacterial activity was a target in the optimization of biologically active compounds and antiseptic agents. Although this targeting is still valuable, a new trend has appeared since the discovery of superhigh resistance of bacterial cells upon their aggregation into groups. Indeed, it is now well established that the great majority of pathogenic germs are found in the environment as surface-associated microbial communities called biofilms. The protective properties of biofilms and microbial resistance, even to high concentrations of biocides, cause many chronic infections in medical settings and lead to serious economic losses in various areas. A paradigm shift from individual bacterial targeting to also affecting more complex cellular frameworks is taking place and involves multiple strategies for combating biofilms with compounds that are effective at different stages of microbiome formation. Quaternary ammonium compounds (QACs) play a key role in many of these treatments and prophylactic techniques on the basis of both the use of individual antibacterial agents and combination technologies. In this review, we summarize the literature data on the effectiveness of using commercially available and newly synthesized QACs, as well as synergistic treatment techniques based on them. As an important focus, techniques for developing and applying antimicrobial coatings that prevent the formation of biofilms on various surfaces over time are discussed. The information analyzed in this review will be useful to researchers and engineers working in many fields, including the development of a new generation of applied materials; understanding biofilm surface growth; and conducting research in medical, pharmaceutical, and materials sciences. Although regular studies of antibacterial activity are still widely conducted, a promising new trend is also to evaluate antibiofilm activity in a comprehensive study in order to meet the current requirements for the development of highly needed practical applications.

Enhancement of antifouling properties, metal ions and protein separation of poly(ether-ether-sulfone) ultrafiltration membranes by incorporation of poly ethylene glycol and n-ZnO

Composite polymeric membranes with enhanced anti-fouling properties, antimicrobial activities and flux were produced via the phase inversion technique using poly (ether-ether-sulfone) (PEES)/polyethylene glycol (PEG) and n-ZnO. SEM and ATR-FTIR spectroscopy were used to study the morphological and chemical properties of the resulting ultrafiltration membranes. PEG and n-ZnO concentration has an effect on membrane morphologies, ultrafiltration performance, thermal characteristics, metal ion separation studies, surface hydrophilicity and anti-fouling capabilities. The permeate flux increased when the PEG concentration was raised. This results revealed that adding PEG and n-ZnO to membranes increased their surface hydrophilicity and anti-fouling properties. The inclusion of 1.5 wt % n-ZnO and 5 wt % PEG to the pristine PEES membrane resulted in a higher flux of 233.76 L m^-2 h^-1, 70.09 % of water content, 47.46° of contact angle, the porosity of 30.20 %, and hydraulic resistance of 0.22 kPa/Lm^-2h^-1. Anti-fouling properties of the fabricated membrane were assessed using a model foulant BSA, which revealed a high flux recovery ratio value. As a result, the PEG and n-ZnO incorporated membrane is more hydrophilic than the virgin membrane. In addition, the prepared PEES/PEG/n-ZnO membrane showed a significant increase in metal ions and protein rejection. Furthermore, an antibacterial test of the membrane revealed that the PEG and n-ZnO composite membrane outperformed the bare PEES membrane in terms of antibacterial capabilities. Overall, the findings reveal that combining n-ZnO and PEG resulted in a membrane with improved anti-fouling capabilities and hydrophilicity, making it suitable for water purification.

Recent developments in antibacterial or antibiofilm compound coating for biliary stents

Cholestasis of the indwelling biliary stents usually leads to stone recurrence after endoscopic retrograde cholangio pancreatoraphy (ERCP). Biliary stents, including metallic and none-degradable plastic stents are widely used in clinical settings due to their many excellent properties. However, conventional biliary stents still suffer from poor antibacterial activity and anti-bile-adhesion, which lead to injured, local fibroblasts proliferating. Currently, various coatings for biliary stents have been prepared to meet the clinical demands. In this review, we start by summarizing and discussing classifications of biliary stents and antibacterial/antibiofilm mechanism. Then, the latest advances about developing antibacterial and antibiofilm coatings for improving the properties of biliary stents are reviewed and discussed in detail. Lastly, we list several possible directions for future development of biliary stents coatings and biliary stent, such as anti-bile-adhesion coating, multifunctional coating, drug-eluting biodegradable biliary stents and 3D printed biliary stents.

Poly(vinylidene fluoride)/partially alkylated poly(vinyl imidazole) interpolymer ultrafiltration membranes with intrinsic anti-biofouling and antifouling property for the removal of bacteria

Bacterial contaminated water causes potential health issues. Conventional chlorine treatment has shortcomings of environmental hazards and chlorine adoptability by the bacterial cells. Ultrafiltration membrane can intercept bacterial species from feed water. Membrane having anti-biofouling/antifouling properties is needed for the removal of bacteria from feed water. Herein, interpolymer membranes with inherent antimicrobial activity and fouling release property have been prepared by the blend of poly(vinylidene fluoride) (PVDF), poly(vinyl pyrrolidone) and partially long chain alkylated (C12 chain) poly(vinyl imidazole) copolymer (PVIm-co-PVIm-C12) followed by cross-linking of the remaining VIm groups with an activated di-halide compound. The membranes obtain with copolymers of degree of alkyl substitution (DS_C12) in the range of 0.75-0.85 and amount in the range of 0.9-3.5% w/w in the casting solutions exhibit good antimicrobial activity (>99 % of inhibition) and dynamic anti-biofouling property. The membrane prepared with 0.9% w/w of the copolymer (DS_C12=0.85) shows higher flux recovery ratio (91 % for bacterial filtration and 88 % for protein filtration) compare to a pristine membrane (57 % for bacterial filtration and 58 % for protein filtration). The membrane is able to reject the bacteria completely. Use of small amount of copolymer and facile fabrication of stable anti-biofouling/antifouling membranes show potential for the purification of bacterial contaminated water.

Polymeric Membrane Marine Sensors with a Regenerable Antibiofouling Coating Based on Surface Modification of a Dual-Functionalized Magnetic Composite

Environmentally compatible polymeric membrane marine sensors with excellent antiadhesive and antibacterial properties have recently been developed. However, the regeneration abilities of these sensors after fouling have rarely been investigated. Herein, a novel strategy for preparation of a regenerable antibiofouling coating via surface modification of a dual-functionalized magnetic composite is proposed. A zwitterionic polymer (i.e., poly(sulfobetaine methacrylate)) and a quaternary ammonium compound (i.e., 3-trimethoxysilylpropyl octadecyldimethyl ammonium chloride) are coated on the surface of Fe₃O₄ microspheres for antiadhesion and bacterial inactivation, respectively. The antifouling magnetic composite can readily be modified on the sensor's surface via the magnetically assisted self-assembly technology. Using a polymeric membrane calcium ion-selective electrode as a model sensor, the protection layer-coated electrode shows the markedly improved antibiofouling activities as compared to the unmodified sensor. More importantly, by altering the direction of the external magnetic field, the antifouling coating can easily be removed after fouling along with the removal of the adsorbed bacterial cells from the electrode's surface, which is followed by re-modifying a fresh coating for regeneration of the antifouling electrode. The proposed methodology for fabrication of a regenerable antibiofouling coating is promising to improve the durability of a marine sensor.

Surface Functionalities of Polymers for Biomaterial Applications

Changes of a material biointerface allow for specialized cell signaling and diverse biological responses. Biomaterials incorporating immobilized bioactive ligands have been widely introduced and used for tissue engineering and regenerative medicine applications in order to develop biomaterials with improved functionality. Furthermore, a variety of physical and chemical techniques have been utilized to improve biomaterial functionality, particularly at the material interface. At the interface level, the interactions between materials and cells are described. The importance of surface features in cell function is then examined, with new strategies for surface modification being highlighted in detail.

Advancements in modification of membrane materials over membrane separation for biomedical applications-Review

A comprehensive overview of various modifications carried out on polymeric membranes for biomedical applications has been presented in this review paper. In particular, different methods of carrying out these modifications have been discussed. The uniqueness of the review lies in the sense that it discusses the surface modification techniques traversing the timeline from traditionally well-established technologies to emerging new techniques, thus giving an intuitive understanding of the evolution of surface modification techniques over time. A critical comparison of the advantages and pitfalls of commonly used traditional and emerging surface modification techniques have been discussed. The paper also highlights the tuning of specific properties of polymeric membranes that are critical for their increased applications in the biomedical industry specifically in drug delivery, along with current challenges faced and where the future potential of research in the field of surface modification of membranes.

Effects of Benzalkonium Chloride Contents on Structures, Properties, and Ultrafiltration Performances of Chitosan-Based Nanocomposite Membranes

The effects of benzalkonium chloride (BKC) contents on the structure, properties, and ultrafiltration performance of chitosan-based nanocomposite membranes containing poly(ethylene glycol) and multi-walled carbon nanotube (chitosan/BKC/PEG/CNT) were examined. The membranes were prepared by a mixing solution method and phase inversion before being characterized with microscopic techniques, tensile tests, thermogravimetric analysis, water contact angle, and porosity measurements. The performance of the nanocomposite membranes in regard to permeability (flux) and permselectivity (rejection) was examined. The results show that the incorporation of BKC produced nanocomposite membranes with smaller pore structures and improved physico-chemical properties, such as an increase in porosity and surface roughness (Ra = 45.15 to 145.35 nm and Rq = 53.69 to 167.44 nm), an enhancement in the elongation at break from 45 to 109%, and an enhancement in the mechanical strength from 31.2 to 45.8 MPa. In contrast, a decrease in the membrane hydrophilicity (water contact angle increased from 56.3 to 82.8°) and a decrease in the average substructure pore size from 32.64 to 10.08 nm were observed. The membrane rejection performances toward Bovine Serum Albumin (BSA) increased with the BKC composition in both dead-end and cross-flow filtration processes. The chitosan/BKC/PEG/CNT nanocomposite membranes have great potential in wastewater treatments for minimizing biofouling without reducing the water purification performance.

Mitigating membrane biofouling in biofuel cell system – A review

A biofuel cell (BFC) system can transform chemical energy to electrical energy through electrochemical reactions and biochemical pathways. However, BFC faced several obstacles delaying it from commercialization, such as biofouling. Theoretically, the biofouling phenomenon occurs when microorganisms, algae, fungi, plants, or small animals accumulate on wet surfaces. In most BFC, biofouling occurs by the accumulation of microorganisms forming a biofilm. Amassed biofilm on the anode is desired for power production, however, not on the membrane separator. This phenomenon causes severities toward BFCs when it increases the electrode’s ohmic and charge transfer resistance and impedes the proton transfer, leading to a rapid decline in the system’s power performance. Apart from BFC, other activities impacted by biofouling range from the uranium industry to drug sensors in the medical field. These fields are continuously finding ways to mitigate the biofouling impact in their industries while putting forward the importance of the environment. Thus, this study aims to identify the severity of biofouling occurring on the separator materials for implementation toward the performance of the BFC system. While highlighting successful measures taken by other industries, the effectiveness of methods performed to reduce or mitigate the biofouling effect in BFC was also discussed in this study.

Fabrication of a Dual-Action Membrane with Both Antibacterial and Anticoagulant Properties via Cationic Polyelectrolyte-Induced Phase Separation

The development of microorganisms and formation of thrombus on a biomaterial surface can seriously lead to device failure and threaten human health. Nonetheless, a surface that has both antibacterial and anticoagulant properties has scarcely been developed. Herein, a novel dual-action membrane composed of polyethersulfone (PES) bulk material and a hydrophilic anionic poly-2-acrylamido-2-methylpropanesulfonic acid (PAMPS) polymer has been prepared via the cationic antibacterial agent poly(hexamethylene biguanide) (PHMB)-induced phase separation technique. Interestingly, the resultant membrane can offer tunable antibacterial and anticoagulant properties, while maintaining satisfactory permeability and greatly increasing selectivity. The membrane also shows excellent hydrophilicity, a well-defined porous surface, and cross section with a sponge gradient structure. Furthermore, the PHMB-PAMPS complex formed on the membrane surface displays outstanding long-term stability, which is crucial for further practical applications. More importantly, the hollow fiber membrane fabricated by the cationic polyelectrolyte-induced phase separation technique confirms its capability to control the membrane permeability (257.4 L·m^-2·h^-1·bar^-1) and selectivity (95.9%) without destroying the membrane structure. The present work opens a straightforward and efficient avenue for the rational design of a functional surface to fight biomedical material-associated infections.

Toughened chitosan-based composite membranes with antibiofouling and antibacterial properties via incorporation of benzalkonium chloride

Biofouling due to biofilm formation is a major problem in ultrafiltration membrane applications. In this work, a potential approach to solve this issue has been developed by functionalization of chitosan-based membranes with benzalkonium chloride (BKC). The chitosan composite membranes consisting of poly(ethylene glycol) (PEG), multiwalled carbon nanotubes (MWCNT), and BKC were synthesized by mixing the membrane precursors and the antibacterial solution, and casting via an inversed phase technique. The effects of the BKC content on the morphology and performance of the membranes are investigated by varying the BKC feed compositions. The composite membranes demonstrate better antibacterial efficacy against Staphylococcus aureus than Escherichia coli. The permeability and selectivity performances of the composites as filter membranes are examined by employing a dead-end filtration system. Interestingly, enhanced toughness of the membranes is observed as a function of the BKC content. Mechanisms of the structural formation are investigated. The results from SEM, XRD, and FTIR spectroscopy revealed that MWCNT/BKC are located as nanoclusters with π–π stacking interactions, and are covered by PEG chains. The shape of the dispersed domains is spherical at low BKC contents, but becomes elongated at high BKC contents. These act as soft domains with an anisotropic shape with toughening of the brittle chitosan matrix, leading to enhanced durability of the membranes, especially in ultrafiltration applications. The composite membranes also demonstrate improved rejection in dead-end ultrafiltration systems due to high porosity, high hydrophilicity, and the positive charges of the membrane surface.

Chitosan/PEG/MWCNT/BKC membranes exhibit enhanced antibiofouling properties against S. aureus and E. coli. MWCNT/BKC are located as dispersed nano-clusters with π–π stacking interactions in the chitosan matrix, and are coved by PEG chains.

Highly Efficient Antimicrobial and Antifouling Surface Coatings with Triclosan-Loaded Nanogels

Multifunctional nanogel coatings provide a promising antimicrobial strategy against biomedical implant-associated infections. Nanogels can create a hydrated surface layer to promote antifouling properties effectively. Further modification of nanogels with quaternary ammonium compounds (QACs) potentiates antimicrobial activity owing to their positive charges along with the presence of a membrane-intercalating alkyl chain. This study effectively demonstrates that poly(N-isopropylacrylamide-co-N-[3(dimethylamino)propyl]methacrylamide) (P(NIPAM-co-DMAPMA)-based nanogel coatings possess antifouling behavior against S. aureus ATCC 12600, a Gram-positive bacterium. Through the tertiary amine in the DMAPMA comonomer, nanogels are quaternized with a 1-bromo-dodecane chain via an N-alkylation reaction. The alkylation introduces the antibacterial activity due to the bacterial membrane binding and the intercalating ability of the aliphatic QAC. Subsequently, the quaternized nanogels enable the formation of intraparticle hydrophobic domains because of intraparticle hydrophobic interactions of the aliphatic chains allowing for Triclosan incorporation. The coating with Triclosan-loaded nanogels shows a killing efficacy of up to 99.99% of adhering bacteria on the surface compared to nonquaternized nanogel coatings while still possessing an antifouling activity. This powerful multifunctional coating for combating biomaterial-associated infection is envisioned to greatly impact the design approaches for future clinically applied coatings.

Membrane Biofouling Control by Surface Modification of Quaternary Ammonium Compound Using Atom-Transfer Radical-Polymerization Method with Silica Nanoparticle as Interlayer

A facile approach to fabricate antibiofouling membrane was developed by grafting quaternary ammonium compounds (QACs) onto polyvinylidene fluoride (PVDF) membrane via surface-initiated activators regenerated by electron transfer atom-transfer radical-polymerization (ARGET ATRP) method. During the modification process, a hydrophilic silica nanoparticle layer was also immobilized onto the membrane surface as an interlayer through silicification reaction for QAC grafting, which imparted the membrane with favorable surface properties (e.g., hydrophilic and negatively charged surface). The QAC-modified membrane (MQ) showed significantly improved hydrophilicity and permeability mainly due to the introduction of silica nanoparticles and exposure of hydrophilic quaternary ammonium groups instead of long alkyl chains. Furthermore, the coverage of QAC onto membrane surface enabled MQ membrane to have clear antibacterial effect, with an inhibition rate ~99.9% of Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive), respectively. According to the batch filtration test, MQ had better antibiofouling performance compared to the control membrane, which was ascribed to enhanced hydrophilicity and antibacterial activity. Furthermore, the MQ membrane also exhibited impressive stability of QAC upon suffering repeated fouling–cleaning tests. The modification protocols provide a new robust way to fabricate high-performance antibiofouling QAC-based membranes for wastewater treatment.

Membrane processes

This literature review provides a review for publications in 2018 and 2019 and includes information membrane processes findings for municipal and industrial applications. This review is a subsection of the annual Water Environment Federation literature review for Treatment Systems section. The following topics are covered in this literature review: industrial wastewater and membrane. Bioreactor (MBR) configuration, membrane fouling, design, reuse, nutrient removal, operation, anaerobic membrane systems, microconstituents removal, membrane technology advances, and modeling. Other sub-sections of the Treatment Systems section that might relate to this literature review include the following: Biological Fixed-Film Systems, Activated Sludge, and Other Aerobic Suspended Culture Processes, Anaerobic Processes, and Water Reclamation and Reuse. This publication might also have related information on membrane processes: Industrial Wastes, Hazardous Wastes, and Fate and Effects of Pollutants.

Polymeric Coatings Based on Water-Soluble Trimethylammonium Copolymers for Antifouling Applications

Crosslinked polymeric materials based on a quaternary trimethylammonium compound were developed and evaluated as potential antifouling coatings. For this purpose, two water-soluble random copolymers, poly(4-vinylbenzyltrimethylammonium chloride-co-acrylic acid) P(VBCTMAM-co-AAx) and poly(N,N-dimethylacrylamide-co-glycidylmethacrylate) P(DMAm-co-GMAx), were synthesized via free radical polymerization. A water based approach for the synthesis of P(VBCTMAM-co-AAx) copolymer was used. Coatings of the complementary reactive copolymers in different compositions were obtained by curing at 120 °C for one day and were used to coat aquaculture nets. These nets were evaluated in respect to their release rate using Total Organic Carbon (TOC) and Total Nitrogen (TN) measurements. Finally, the antifouling efficacy of these newly-composed durable coatings was investigated for 14 days in accelerated conditions. The results showed that this novel polymeric material provides contact-killing antifouling activity for a short time period, whereas it functions efficiently in biofouling removal after high-pressure cleaning.

Magnetic field assisted preparation of PES-Ni@MWCNTs membrane with enhanced permeability and antifouling performance

Multiple wall carbon nanotubes (MWCNTs), as an excellent material, have been used in various applications including preparation of polymer-MWCNTs composite membranes. However, few reports have combined the magnetic Ni@MWCNTs with polyether sulfone (PES) membrane to improve its antifouling performance to humic acid (HA), sodium alginate (SA), bovine serum albumin (BSA) and yeast (YE) solutions. In this study, the Ni@MWCNTs was generated by immersing MWCNTs into Ni²⁺ solution where in-situ reduction reaction was launched by the adsorbed Ag⁺ on MWCNTs. Since the loaded Ni endowed magnetism to MWCNTs, the Ni@MWCNTs can be easily attracted onto the membrane surface by an external magnetic field during the phase inversion process. The morphology measurements confirmed that the Ni@MWCNTs headed out of the PES-Ni@MWCNTs membrane surface. Because the MWCNTs played a role of free channels for water molecules, the composite membrane water flux reached to threefold flux of the pristine membrane. Moreover, the PES-Ni@MWCNTs membranes displayed the obviously enhanced antifouling ability during all the three alternative filtration cycles of water and BSA, SA, YE and HA solutions. In addition, the optimal PES-Ni@MWCNTs membrane demonstrated a flux recovery rate (FRR) of 67.89%, 85.53%, 60.28 and 90.12% for BSA, SA, YE and HA, respectively, which were not only much higher than that of the pristine membrane, but also exhibited significant improvements comparing with the previous studies. Further results of extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory indicated that the modified membrane possessed advantageous interaction energies with contaminant molecules over the pristine membrane.

The Recent Progress in Modification of Polymeric Membranes Using Organic Macromolecules for Water Treatment

For decades, the water deficit has been a severe global issue. A reliable supply of water is needed to ensure sustainable economic development in population growth, industrialization and urbanization. To solve this major challenge, membrane-based water treatment technology has attracted a great deal of attention to produce clean drinking water from groundwater, seawater and brackish water. The emergence of nanotechnology in membrane science has opened new frontiers in the development of advanced polymeric membranes to enhance filtration performance. Nevertheless, some obstacles such as fouling and trade-off of membrane selectivity and permeability of water have hindered the development of traditional polymeric membranes for real applications. To overcome these issues, the modification of membranes has been pursued. The use of macromolecules for membrane modification has attracted wide interests in recent years owing to their interesting chemical and structural properties. Membranes modified with macromolecules have exhibited improved anti-fouling properties due to the alteration of their physiochemical properties in terms of the membrane morphology, porosity, surface charge, wettability, and durability. This review provides a comprehensive review of the progress made in the development of macromolecule modified polymeric membranes. The role of macromolecules in polymeric membranes and the advancement of these membrane materials for water solution are presented. The challenges and future directions for this subject are highlighted.

Radical polymerization as a versatile tool for surface grafting of thin hydrogel films

The surface of solid substrates is the main part that interacts with the environment.