Tunicate cellulose nanocrystals modified commercial filter paper for efficient oil/water separation

An Assessment of the Catalytic and Adsorptive Performances of Cellulose Acetate-Based Composite Membranes for Oil/Water Emulsion Separation

Cellulose acetate (CA) mixed-matrix membranes incorporating polyvinylpyrrolidone (PVP), bentonite (B or Ben), graphene oxide (GO), and titanium dioxide (TiO2) were prepared by the phase inversion separation technique for oil/water separation. An investigation was performed where the mixed-matrix membrane was tested for the separation performance of hydrophilic and hydrophobic surface properties. An ultrafiltration experiment at the laboratory scale was used to test dead-end ultrafiltration models developed for the treatment performances of oily wastewater under dynamic full-scale operating conditions. Artificial oily wastewater solutions were prepared from hexane, toluene, and engine oil with Tween80 emulsions for oil removal treatment using composite membranes. The impacts of material hydrophilicity, weight loss, permeability, and pore size were investigated, and it was found that the oil retention of membranes with larger pore sizes enabled much more sophisticated water flux. The CA-GO-, CA-B-, and CA-TiO2-incorporated membranes achieved pure water flux (PWF) values of 45.19, 53.41, and 100.25 L/m2h, respectively. The performance of CA-TiO2 in oil/water emulsion rejection was assessed, and the rejection of engine oil/water, toluene/water, and hexane/water mixtures was determined to be 95.21%, 90.33%, and 92.4%, respectively. The CA-based mixed-matrix membrane portrayed better antifouling properties due to enhanced hydrophilicity and water molecules. The CA-TiO2-incorporated membrane possessed the potential to provide high separation efficiency for oily wastewater treatment. This study demonstrates the potential of fine-tuning membrane performances through material hybridization to achieve efficient wastewater treatment.

Green Fabrication of Superhydrophilic/Underwater Superoleophobic Composite Membrane for High-Efficiency Oil/Water Separation in Harsh Environments

Due to the high oil spill incidence and industrial wastewater discharge including oil and emulsified oil, designing and synthesizing oil-water separation materials which can maintain stability under harsh environmental conditions with high separation efficiencies remains a great challenge. The present work developed an easy, green, cost-effective, and easily scaled-up approach for fabricating cellulose-based membranes. First, we coated polydopamine (PDA) onto fibers of filter membrane (FM). Then, the PDA-FM membrane was immersed into the mixed solution of poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) and further thermally cross-linked at 150 °C to create a superhydrophilic/underwater superoleophobic membrane (PVA/PAA@PDA-FM) to separate oil/water mixtures. The simple thermally cross-linking process promotes multiple covalent chemical bonds generation between cellulose filter membrane, PAA, PDA, and PVA, endowing membranes with excellent stability and resistance to acidity, alkalinity, and salinity. The PVA/PAA@PDA-FM membrane not only demonstrates great separation performance (>99.8%) and great flux (>1000 L m-2 h-1) in oil-water immiscible mixtures but also maintains high separation efficiency under conditions of high acidity, alkalinity, and salinity. Additionally, the PVA/PAA@PDA-FM membrane exhibits excellent separation capacity in oil-water emulsions, which can maintain the >99.6% separation efficiency even after 40 cycles in harsh environments, showing outstanding reusability. Thus, due to the multiple cross-linked networks in the membrane, the excellent performance makes the PVA/PAA@PDA-FM membrane a good application prospect in water purification and oily wastewater treatment.

Construction of biodegradable superhydrophilic/underwater superoleophobic materials with CNF (cellulose nanofiber) fence-like attached on the surface for efficient oil/water emulsion separation

Superhydrophilic/underwater superoleophobic materials for the separation of oil-water emulsions by filtration have received much attention in order to solve the pollution problem of oil-water emulsion. In this paper, a fence-like structure on the surface of CNF/KGM (Konjac Glucomannan) materials by a simple method using CNF instead of metal nanowires was successfully developed based on the hydrogen bonding of KGM and CNF. The resulted organic CNF/KGM materials surface has outstanding superhydrophilic (WCA = 0°) in air and superoleophobicity (OCA≥151°) in water, which could separate oil-water mixtures with high separation efficiency above 99.14 % under the pressure of the emulsion itself. The material shows good mechanical properties because of the addition of CNF and has outstanding anti-fouling property and reusability. More importantly, the material can be completely biodegraded after buried in soil for 4 weeks since both of KGM and CNF are organic substances. Therefore, it may have a broad application prospect in the separation of oil-water emulsion because of its outstanding separation properties, simply preparation method and biodegradability.

An efficient solution based on the synergistic effects of nickel foam in NiFe-LDH nanosheets for oil/water separation

Efficient oil-water separation has always been a research hotspot in the field of environmental studies. Employing a one-step hydrothermal approach, NiFe-layered double hydroxides (LDH) nanosheets were synthesized on nickel foam substrates. The resulting NiFe-LDH/NF membrane exhibited rejection rates exceeding 99% across six diverse oil-water mixtures, concurrently demonstrating a remarkable ultra-high flux of 1.4 × 106 L·m-2·h-1. This flux value significantly surpasses those documented in existing literature, maintaining stable performance over 1000 manual filtration cycles. These breakthroughs stem from the synergistic interplay among the three-dimensional channels of the nickel foam, the nanosheets, and the hydration layer. By leveraging the pore size of the foam to enhance the functionality of the hydration layer, the conventional trade-off between permeability and selectivity was transformed into a balanced force relationship between the hydration layer and the oil phase. The operational and failure mechanisms of the hydration layer were examined using the prepared NiFe-LDH/NF membrane, validating the correlation between oil phase viscosity and density with hydration layer rupture. Additionally, an extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory was employed to investigate changes in interaction energy, further reinforcing the study's findings. This research contributes novel insights and assistance to the comprehension and application of hydration layers in other membrane studies dedicated to oil-water separation.

Bio-Inspired Functional Materials for Environmental Applications

With the global population expected to reach 9.7 billion by 2050, there is an urgent need for advanced materials that can address existing and developing environmental issues. Many current synthesis processes are environmentally unfriendly and often lack control over size, shape, and phase of resulting materials. Based on knowledge from biological synthesis and assembly processes, as well as their resulting functions (e.g., photosynthesis, self-healing, anti-fouling, etc.), researchers are now beginning to leverage these biological blueprints to advance bio-inspired pathways for functional materials for water treatment, air purification and sensing. The result has been the development of novel materials that demonstrate enhanced performance and address sustainability. Here, an overview of the progress and potential of bio-inspired methods toward functional materials for environmental applications is provided. The challenges and opportunities for this rapidly expanding field and aim to provide a valuable resource for researchers and engineers interested in developing sustainable and efficient processes and technologies is discussed.

Recent advances in nanocellulose-based two-dimensional nanostructured membranes for sustainable water purification: A review

Nanocellulose (NC), a one-dimensional nanomaterial, is considered a sustainable material for water and wastewater purification because of its promising hydrophilic surface and mechanical characteristics. In this regard, nanostructured membranes comprising NC and two-dimensional (2D) nanomaterials emerged as advanced membranes for efficient and sustainable water purification. This article critically reviews the recent progress on NC-2D nanostructured membranes for water and wastewater treatment. The review highlights the main techniques employed to fabricate NC-2D nanostructured membranes. The physicochemical properties, including hydrophilicity, percent porosity, surface roughness, structure, and mechanical and thermal stability, are summarized. The key performance indicators such as permeability, rejection, long operation stability, antifouling, and interaction mechanisms are thoroughly discussed to evaluate the role of NC and 2D nanomaterials. Finally, summary points and future development work are highlighted to overcome the challenges for potential practical applications. This review contributes to the design and development of advanced membranes to solve growing water pollution concerns in a sustainable manner.

Cellulose nanocrystals in the development of biodegradable materials: A review on CNC resources, modification, and their hybridization

The escalating demand for sustainable materials has propelled cellulose into the spotlight as a promising alternative to petroleum-based products. As the most abundant organic polymer on Earth, cellulose is ubiquitous, found in plants, bacteria, and even a unique marine animal-the tunicate. Cellulose polymers naturally give rise to microscale semi-crystalline fibers and nanoscale crystalline regions known as cellulose nanocrystals (CNCs). Exhibiting rod-like structures with widths spanning 3 to 50 nm and lengths ranging from 50 nm to several microns, CNC characteristics vary based on the cellulose source. The degree of crystallinity, crucial for CNC properties, fluctuates between 49 and 95 % depending on the source and synthesis method. CNCs, with their exceptional properties such as high aspect ratio, relatively low density (≈1.6 g cm-3), high axial elastic modulus (≈150 GPa), significant tensile strength, and birefringence, emerge as ideal candidates for biodegradable fillers in nanocomposites and functional materials. The percolation threshold, a mathematical concept defining long-range connectivity between filler and polymer, governs the effectiveness of reinforcement in nanocomposites. This threshold is intricately influenced by the aspect ratio and molecular interaction strength, impacting CNC performance in polymeric and pure nanocomposite materials. This comprehensive review explores diverse aspects of CNCs, encompassing their derivation from various sources, methods of modification (both physical and chemical), and hybridization with heterogeneous fillers. Special attention is devoted to the hybridization of CNCs derived from tunicates (TCNC) with those from wood (WCNC), leveraging the distinct advantages of each. The overarching objective is to demonstrate how this hybridization strategy mitigates the limitations of WCNC in composite materials, offering improved interaction and enhanced percolation. This, in turn, is anticipated to elevate the reinforcing effects and pave the way for the development of nanocomposites with tunable viscoelastic, physicochemical, and mechanical properties.

Preparation of Superhydrophilic/Underwater Superoleophobic and Superhydrophobic Stainless Steel Meshes Used for Oil/Water Separation

Robust membrane materials with high efficiency have attracted extensive attention in oil/water separation. In this work, carbon particles via candle combustion were firstly adsorbed on the surface of stainless steel meshes (SSMs), which formed a thin hydrophobic coating, and a rough structure was then constructed through chemical vapor deposition and high temperature calcination, with the resultant SSM surface wrapped with uniform silica coating possessing the characteristic of superoleophobicity underwater. Scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and X-ray powder diffraction (XRD) were used to characterize the modified SSMs. The prepared SSMs were superhydrophilic in air, and they had superoleophobicity underwater (157.4°). The separation efficiency of five oil/water mixtures was above 98.8%, and the separation flux was 46,300 L·m^-2·h^-1. After it was immersed in 1 mol/L NaOH, 1 mol/L HCl and 3.5 wt% NaCl for 24 h, respectively, the efficiency was still above 97.3%. Further immersion in the solution of dopamine and octadecylamine resulted in the transformation of superhydrophililc/superoleophobicity-underwater SSMs to superhydrophobic SSMs, and the resultant SSMs with reverse surface wettability was also used for the oil/water separation with good separation efficiency and separation flux.

Injectable, self-healable and antibacterial multi-responsive tunicate cellulose nanocrystals strengthened supramolecular hydrogels for wound dressings

Wound dressing with an improved structural and functional recapitulation of damaged organs, efficient self-healing and antibacterial properties that can well integrate with tissue are urgently needed in wound management. Supramolecular hydrogels confer control over structural properties in a reversible, dynamic and biomimetic fashion. Herein, a kind of injectable, self-healing and antibacterial supramolecular hydrogel with multi-responses were fabricated by mixing phenylazo-terminated Pluronic F127, quaternized chitosan-graft-cyclodextrin and polydopamine coated tunicate cellulose nanocrystals under physiological conditions. By exploiting the photoisomerization of azobenzene under different wavelengths, a supramolecular hydrogel featuring a changing crosslink density of network was obtained. The corporation of polydopamine coated tunicate cellulose nanocrystals strengthens the hydrogel network with Schiff base bonds and hydrogen bonds, which avoids complete gel-sol transition. The inherent antibacterial property, drug release behavior, self-healing ability, hemostatic performance and biocompatibility were investigated to confirm superiority in wound healing. Moreover, the curcumin loaded hydrogel (Cur-hydrogel) showed multi-responsive release profiles (light, pH, and temperature). A full-thickness skin defect model was built to confirm that Cur-hydrogels significantly accelerated wound healing rate with better granulation tissue thickness and collagen disposition. Overall, the novel photo-responsive hydrogel with coherent antibacterial property has great potential in the healthcare of wound healing.

Crosslinked poly (vinyl alcohol) composite reinforced with tunicate, wood, and hybrid cellulose nanocrystals: Comparative physicochemical, thermal, and mechanical properties

The development of sustainable and biodegradable composites has gained increasing attention in recent years. Effective interaction and adhesion between polymers and fillers are crucial. In this study, the effect of different aspect ratios of cellulose nanocrystals (CNCs) and their hybrid within a crosslinked poly (vinyl alcohol) (PVA) nanocomposite has been investigated to develop biodegradable materials. The physicochemical, thermal, and mechanical properties of the specimens have been studied. SEM images indicate that the addition of CNC reduced the porosity of the films. The XPS results confirmed the significant formation of covalent bonds for all composites except those reinforced with wood-CNC, which showed a lower amount of crosslinking and CC formation. EDS maps reveals that the dispersity of the CNCs could be different depending on the aspect ratio of the CNCs. Results from the solubility in water (SW) tests indicated that the use of hybrid-CNC in a crosslinked system decreased the SW significantly. The crosslinking and addition of CNC to the PVA composite led to improved mechanical properties. Elongation at break (EB) decreased significantly for the crosslinked hybrid-CNC nanocomposite. Overall, the results of this study indicate that the aspect ratio of CNCs as fillers in nanocomposites may contribute to their physicochemical, mechanical, and thermal properties for the development of biodegradable materials.

Development of Lignin-Containing Cellulose Nanofibrils Coated Paper-Based Filters for Effective Oil-Water Separation

New methods of oil-water separation are needed as industrialization has increased the prevalence of oil-water mixtures on Earth. As an abundant and renewable resource with high oxygen and grease barrier properties, mechanically refined cellulose nanofibrils (CNFs) may have promising applications for oil-water separations. The unbleached form of these nanofibrils, lignin-containing CNFs (LCNFs), have also been found to display extraordinary barrier properties and are more environmentally friendly and cost-effective than CNFs. Herein, both wet and dry LCNF-modified filter papers have been developed by coating commercial filter paper with an LCNF suspension utilizing vacuum filtration. The LCNF-modified filters were tested for effectiveness in separating oil-water emulsions, and a positive relationship was discovered between a filter's LCNF coat weight and its oil collection capabilities. The filtration time was also analyzed for various coat weights, revealing a trend of high flux for low LCNF coat weights giving-way-to predictions of a coat weight upper limit. Additionally, it was found that wet filters tend to have higher flux values and oil separation efficiency values than dry filters of the same LCNF coat weight. Results confirm that the addition of LCNF to commercial filter papers has the potential to be used in oil-water separation.

Application of cellulose nanocrystals in water treatment membranes: A review

Nanomaterials have brought great changes to human society, and development has gradually shifted the focus to environmentally friendly applications. Cellulose nanocrystals (CNCs) are new one-dimensional nanomaterials that exhibit environmental friendliness and ensure the biological safety of water environment. CNCs have excellent physical and chemical properties, such as simple preparation process, nanoscale size, high specific surface area, high mechanical strength, good biocompatibility, high hydrophilicity and antifouling ability. Because of these characteristics, CNCs are widely used in ultrafiltration membranes, nanofiltration membranes and reverse osmosis membranes to solve the problems hindering development of membrane technology, such as insufficient interception and separation efficiency, low mechanical strength and poor antifouling performance. This review summarizes recent developments and uses of CNCs in water treatment membranes and discusses the challenges and development prospects of CNCs materials from the perspectives of ecological safety and human health by comparing them with traditional one-dimensional nanomaterials.

PDMS/PVDF Electrospinning Membranes for Water-in-Oil Emulsion Separation and UV Protection

With industry development, the separation of oily wastewater is becoming more critical. Inspired by organisms such as lotus leaves, biomimetic superhydrophobic surfaces with micro-nano structures have shown great potential in this regard. In this work, PDMS/PVDF oil-water separation membranes with designed microstructures were prepared by electrospinning technology. The membrane-forming effect of electrospinning with different ratios of PDMS and PVDF was studied. The study found that membranes with high PDMS content were more likely to form microspheres, and PDMS tended to concentrate on the microspheres. The results also showed that the microspheres would bring better hydrophobicity to the membrane. When the ratio of PDMS to PVDF is 1:2, the membrane has a water contact angle of up to 150° and an oil contact angle of 0°. At this ratio, the separation efficiency of the membrane for the water-in-oil emulsion is 98.7%, and it can still maintain more than 98% after ten separation cycles, which is a good candidate for oil-water separation. Furthermore, microspheres enable the membrane to achieve macroscopic uniformity and microscopic phase separation so that the membranes have both good elongation and fracture strength. In addition, the PDMS/PVDF membranes also exhibit excellent UV resistance, and their UV protection factor is greater than 185, making them a potential UV protective material.

Bacterial cellulose: A promising biopolymer with interesting properties and applications

The ever-increasing demands for materials with desirable properties led to the development of materials that impose unfavorable influences on the environment and the ecosystem. Developing a low-cost, durable, and eco-friendly functional material with biological origins has become necessary to avoid these consequences. Bacterial cellulose generated by bacteria dispenses excellent structural and functional properties and satisfies these requirements. BC and BC-derived materials are essential in developing pure and environmentally safe functional materials. This review offers a detailed understanding of the biosynthesis of BC, properties, various functionalization methods, and applicability in biomedical, water treatment, food storage, energy conversion, and energy storage applications.

Antibacterial nanocellulose membranes coated with silver nanoparticles for oil/water emulsions separation

The superhydrophilic/underwater superoleophobic nanocellulose-based membranes show great potential in oil/water emulsion separation. However, nanocellulose composed of polysaccharides inevitably suffered from bacterial erosion during use or storage, resulting in structural damage or reduced separation efficiency. In this work, silver nanoparticles (AgNPs) as effective bactericidal materials are uniformly deposited on tunicate cellulose nanocrystals (TCNCs) by in situ hydrothermal reduction of silver nitrate. TCNCs not only act as reducing agents for silver ions, but also work as dispersant and stabilizers of AgNPs. Nanocomposite membranes are fabricated by vacuum-assisted filtrating of AgNPs@TCNC suspension, which exhibit nanoporous structure, superhydrophilicity, and underwater superoleophobicity. These membranes could efficiently separate oil/water microemulsion with water flux (>324 L m^-2 h^-1 bar^-1) and oil rejection (>99%). Importantly, these membranes show excellent antibacterial efficacy against E. coli and S. aureus, benefiting to their long-term use and storage.

Preparation and characterization of super hydrophobic aerogels derived from tunicate cellulose nanocrystals

First time aerogels composite with super hydrophobic properties were developed by using tunicate cellulose nanocrystals (TCNC), which expanded the application scope of animal cellulose resources. In this study, the TCNC was firstly cross-linked with silica and methyltrimethylsilane (MTMS), further coated with fluorodopa to form an aerogel with super hydrophobic properties. The aerogel was characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectra (FT-IR), and X-ray photoelectron spectroscopy (XPS). Results indicated that the contact angle of aerogel was 158.7°, which showed good hydrophobicity. The composite aerogel has superior stability in wide pH range, after 72 h immersion in pH = 0 and 12 solutions, the contact angle was still greater than 150°. The aerogel shows excellent oil-water separation ability and it can be repeatedly used more than 10 times. The separation efficiency can all reach more than 90% for different water-oil mixtures. This synthesized super hydrophobic aerogels derived from tunicate cellulose has greatly extended the application of marine animal celluloses.

Synergistic adjustment of water channels and light absorption pathways to co-generate salt collection and clean water production

Solar-driven interface evaporation for clean water production has attracted significant concern due to its energy-saving and environmental protection. However, it is still challenging for the evaporator to continuously and efficiently produce clean water in practical applications because of salt particle deposits and insufficient water supply. Here, an improved and easy-to-manufacture solar evaporator device (Co-NCNT-GO system) enhances water supply and light absorption by introducing a water supply layer (melamine sponge) and bamboo-like structure carbon nanotubes embedded with metal cobalt particles (Co-NCNT). The salt accumulation on the edge of the Co-NCNT-GO film is achieved by controlling the concentration gradient of brine in the center area and the edge area of the film. This paper aims to study the photothermal mechanism of the Co-NCNT-GO system through a series of characterization and theoretical calculations (DFT) and discuss the influence of different water supply areas on the salt recovery capacity. The results show that Co-NCNT-GO significantly reduces the band (0.054 au) between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUNO) by graphite nitrogen-doped CNTs, which is beneficial to improve the light-to-heat conversion capability. Furthermore, the Co-NCNT-GO film has good water wettability due to the higher adsorption energy of pyridine nitrogen and water molecules in Co-NCNT (-9.33 kcal/mol). Simultaneously, it is found that the water evaporation capacity and water supply capacity significantly affect whether the salt can be continuously crystallized at the edge of the film. When the ratio of water supply area to light and heat area is 4:2.5, the salt recovery rate is 46.54 g m^-2 h^-1 during 108 h continuous desalination under one sun illumination. This rationally designed structure and adjustable water transport channel can simultaneously meet high-efficiency evaporation and salt recovery, which can have great potential in practical applications.

Cellulose-based special wetting materials for oil/water separation: A review

Oil spill accidents and oily wastewater discharged by petrochemical industries have severely wasted water resources and damaged the environment. The use of special wetting materials to separate oil and water is efficient and environment-friendly. Cellulose is the most abundant renewable resource and has natural advantages in removing pollutants from oily wastewater. The application and modification of cellulose as special wetting materials have attracted considerable research attention. Therefore, we summarized cellulose-based superlipophilic/superhydrophobic and superhydrophilic/superoleophobic materials exhibiting special wetting properties for oil/water separation. The treatment mechanism, preparation technology, treatment effect, and representative projects of oil-bearing wastewater are discussed. Moreover, cellulose-based intelligent-responsive materials for application to oil/water separation and the removal of other pollutants from oily wastewater have also been summarized. The prospects and potential challenges of all the materials have been highlighted.

Surface engineering of cellulose film with myristic acid for high strength, self-cleaning and biodegradable packaging materials

Developing sustainable, renewable, hydrophobic, and biodegradable packaging material to replace petroleum-based plastic products remains a challenge. Herein, original cellulose/myristic acid composite films were fabricated by solvent-vaporized controllable crystallization of natural myristic acid on anisotropic cellulose films. The myristic acid crystals that evenly distributed on the surface of cellulose film generated micronano binary structure and the interstitial space between microplates, resulting in high hydrophobicity (water contact angle = 132°) and excellent self-cleaning property of the composite film. The resultant film exhibited good tensile strength and toughness under both dry (188.7 MPa, 34.4 MJ m^-3) and humid conditions (119.9 MPa, 28.7 MJ m^-3). Moreover, these composite films could be degraded completely after approximately 102 days in soil with an average environment temperature of 32 °C. This work provided a low-cost and sustainable pathway for the fabrication of high-strength, self-cleaning, and waterproof packaging materials instead of plastics.

A bi-modal, cellulose-based sensor for fluorometric detection of Fe(III) and antimicrobial studies of its silver-loaded form

The study reports designing of a new, low-cost and environmentally friendly colorimetric and fluorometric sensor by using cellulose-based materials for detection and determination of Fe(III). To make powder cellulose (Cel) and filter paper (PCel) fluorescent, they were modified with hexamethylene diisocyanate (HMDI) and 4-sulfo-1,8-naphthalimide (Nap). Fluorescent Cel-Nap and PCel-Nap materials were used for spectroscopic detection of Fe(III). The working range of the designed sensor was determined as 1.0 × 10^-5-4.5 × 10^-5 M with a low limit of detection (LOD) (7.51 μM). Antimicrobial properties of cel-based compounds and Ag(I)-containing compounds were tested against five bacteria; Bacillus cereus, Streptococcus mutans, Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and two fungi; Candida albicans and Candida tropicalis. The materials exhibited antimicrobial effects and their antifungal properties were more effective than their antibacterial properties.

Biomimicking properties of cellulose nanofiber under ethanol/water mixture

The two types of cellulose nanofiber (CNF) surface characteristics were evaluated by oil contact angle under ethanol-water solution at several concentrations as well as in air. Wood pulp-based 2,2,6,6-tetramethylpiperidine-1-oxylradical (TEMPO)-oxidized cellulose nanofiber (TOCNF) sheets and bamboo-derived mechanical counter collision cellulose nanofiber (ACC-CNF) sheets were fabricated by casting followed by drying. The CNF shows underwater superoleophobic mimicking fish skin properties and slippery surface mimicking Nepenthes pitcher. The underwater superoleophobic properties of CNF was evaluated theoretically and experimentally. The theoretical calculation and experimental results of contact angle showed a large deviation. The roughness, zeta potential, and water absorption at different concentrations were key factors that determine the deviation. Antifouling investigation revealed that CNF was a good candidate for antifouling material.

Robust Superhydrophobic Membrane for Solving Water-Accelerated Fatigue of ZDDP-Containing Lubricating Oils

Superwetting materials show distinct advantages in interfacial applications such as oil-water separation. However, it remains a challenge to solve water-accelerated fatigue of lubricating oils owing to the poor mechanical durability of superhydrophobic surfaces and the intractable emulsions stabilized by additives. In this work, a robust superhydrophobic membrane for solving water-accelerated fatigue of lubricating oils containing zinc dialkyldithiophosphate (ZDDP) as a typical antiwear additive is presented. An all-inorganic coating is constructed by SiO₂ nanoparticles and aluminum phosphate using a simple spray-coating method. After silanization, the prepared membrane can extremely repel water and effectively separate ZDDP-stabilized water-in-lubricating oil emulsions (the purities of the collected lubricating oils are over 99.995%), even after sand impingement for 100 cycles. Ball-on-disk tribological tests at severe contact pressures reveal that the reclaimed lubricating oils recover the protective ability, and the catalytic dehydrogenation of lubricating oil is dramatically suppressed to avoid producing a mass of unwanted carbon-based wear debris. This work advances the development of superwetting materials in the lubricating oil industry.

Preparation of cellulose-coated cotton fabric and its application for the separation of emulsified oil in water

Cellulose is a natural material with dissolution-regeneration property and numerous hydrogen bonds in the molecule. By utilizing these properties, this paper reported the development of a multi-functional fabric consisting of cellulose and commercial cotton fabric. The morphology, mechanical and thermal properties along with the oil-water separation performance of the developed material were studied. The results showed that the cellulose dissolved in NaOH/urea solution was regenerated in a salt solution, and attached tightly onto the cotton fabric, forming a sandwich structure for the material. Such modification significantly enhanced the strength, thermal stability and hydrophilic performance of the fabrics. Interestingly, the prepared material exhibited a unique underwater oleophobic performance, and had the capability to separate highly emulsified oil-water mixtures. The relatively low cost for the material preparation, enhanced mechanical property and high separation performance distinguished the developed material a suitable candidate for the separation of emulsified oil from water in practical applications.

Flexible Underwater Oleophobic Cellulose Aerogels for Efficient Oil/Water Separation

Hybrid cellulose/N,N'-methylene bisacrylamide/graphene oxide (GO) aerogels with high flexibility and underwater oleophobicity were fabricated via the NaOH/urea solvent system. The as-prepared aerogels demonstrated low density, high porosity, and good flexibility. Underwater oleophobicity is attributed to the abundant hydrophilic groups in the aerogel skeleton, rough surface, and homogeneous distribution of GO. The samples were shaped into the membrane and filtered for oil/water separation by gravity. The separation efficiency over membrane-shaped CG₁ was 99.8% with a permeate flux of 22,900 L/(m²·h). Moreover, excellent reusability and durability were observed under long-term tests and corrosive conditions.

Isolation of hierarchical cellulose building blocks from natural flax fibers as a separation membrane barrier

Cellulose nanofibrils (CNF) is a natural nanomaterial composed of biomacromolecules that can be extracted from plants and has great potential applications in many fields due to its excellent regenerative, sustainable, and biodegradable properties. In this work, the flax CNF with hierarchical scales was obtained by using the flax fibers (FF) treated with different concentrations of alkaline solution, followed by the TEMPO-mediated ternary oxidation and mechanical treatment. Subsequently, the resultant CNF was implanted on the commercial filter paper as a surface barrier for oil/water preparation. The changes of cellulose crystal form and crystallinity caused by alkali treatment on FF were studied by Fourier transform infrared spectroscopy and X-ray diffraction. Morphological changes of FF before and after alkali treatment were observed. The morphology of obtained CNF was examined. Moreover, the transmittance of the prepared CNF suspension and films was also investigated by a UV spectroscopy. The prepared modified filter paper can effectively separate the oil/water mixture, which gives themselves promise as candidates in practical applications of oil/water separation.