Photocatalytic degradation of organic dye via atomic layer deposited TiO2 on ceramic membranes in single-pass flow-through operation

Photodegradation of steroid hormone micropollutants with palladium-porphyrin coated porous PTFE of varied morphological and optical properties

In flow-through reactors, the photodegradation rate can be improved by enhancing contact and increasing the photocatalyst loading. Both can be attained with a higher surface-to-volume ratio. While previous studies focused on thin membranes (30 - 130 µm) with small pore sizes of 20 - 650 nm, this work employed poly(tetrafluoroethylene) (PTFE) supports, of which pore sizes are in the order of 10 µm, while the porosities and thicknesses are variable (22.5 - 45.3 % and 0.2 - 3 mm, respectively). These porous materials were anticipated to allow a higher loading of porphyrin photosensitisers and better light penetration for subsequent photodegradation of steroid hormone micropollutants via singlet oxygen (1O2) generation. The reactor surface refers to the surface within the PTFE pores, while the reactor volume is the total void space inside these pores. The surface-to-volume ratios between 105 and 106 m2/m3 are higher than those of typical microreactors (103 to 104 m2/m3). The weighted average light transmittance varied from 38 % with the thinnest and most porous support to 4.8 % with the thickest support. Good light penetration combined with minimal absorption by PTFE enhanced the light utilisation of the porphyrins when coated in the porous supports. Changes in the support porosity of the coated supports minimally affected steroid hormone removal, because the collision frequency in the very large pores remained relatively constant. However, varying the support thickness, porphyrin loading (0.3 - 7.7 μmol/g), and water flux (150 - 3000 L/m2.h), hence the resulting hydraulic residence time, influenced the collision frequency and steroid hormone removal. Results showed that the supports did not outperform membranes most likely because the larger pore size in the former limited contact between the hormones and 1O2. From photostability testing of the pristine supports, perfluoroalkyl substances (PFAS) released from the supports were found at 10 - 300 ng/L concentrations during accelerated ageing. While PFAS formation was detectable, the quantities during water treatment operations would be extremely low. In summary, this study elucidates the capability and limitations of porous supports coated with photosensitisers to remove waterborne micropollutants.

Fabrication of a Novel PES/CNTs@TiO2 Membrane Combining Photo-Electrocatalysis and Filtration for Organic Pollutant Removal

Membrane filtration has been widely used in wastewater treatment; contaminants attached to the membrane surface led to flux loss and service life reduction. In the present study, a photo-electrocatalysis membrane was fabricated with CNTs@TiO2 deposited on a commercial polyethersulfone (PES) membrane (PES/CNTs@TiO2). XRD and SEM characterization proved that the CNTs@TiO2 composites were successfully fabricated using the one-pot hydrothermal method. Additionally, vacuum filtration was used to distribute the as-prepared powder on the PES membrane. In CNTs@TiO2, TiO2 particles were deposited on the outer layer of CNTs, which benefits light adsorption and photocatalytic reaction. The hydrophilicity, light absorption ability, and electron transfer rate of the PES/CNTs@TiO2 membrane were enhanced compared with the pristine PES membranes. Organic compound removal was improved in the photo-electrocatalysis filtration system with the improvement of 32.41% for methyl orange (MO), 26.24% for methyl blue (MB), 7.86% for sulfamethoxazole (SMZ), and 25.19% for florfenicol (FF), respectively. Moreover, the hydrophilicity and removal rate could be restored after pure water cleaning, demonstrating excellent reusability. The quenching experiment showed that ·OH and ·O2- were the main reactive oxygen species. This work provides a convenient form of photo-electrocatalysis filtration technology using modified commercial membranes, which has great potential for practical application.

Hybrid combination of advanced oxidation process with membrane technology for wastewater treatment: gains and problems

Over the past few decades, significant efforts have been dedicated to advancing technologies for the removal of micropollutants from water. Achieving complete pure water with a single treatment process is challenging and nearly impossible. One promising approach among various alternatives is adopting hybrid technology, which is considered as a win-win technology. It utilizes the advantages of each technique, resulting in the enhancement of wastewater treatment. This pioneering idea is designed to significantly enhance water quality, addressing real-world implementation hurdles, and offer a promising solution to the worldwide issue of water scarcity. This review assesses the merits and drawbacks of the hybrid photocatalytic membrane technology employed in wastewater treatment. Notably, this hybrid process not only improves the membrane filtration capacity and permeates water quality but also enhances the antifouling performance of the membrane. However, it is crucial to acknowledge potential drawbacks, such as membrane structure degradation and photocatalytic activity loss in nanoparticles during the operation period. While improvements in wastewater treatment efficiency are evident, there remains ample room for further enhancements. The review summarizes the future directions and challenges of implementing such an integrated system.

Heterostructure g-C3N4/Bi2MoO6 PVDF nanofiber composite membrane for the photodegradation of steroid hormone micropollutants

Photocatalytic membrane reactors (PMRs) are a promising technology for micropollutant removal. Sunlight utilization and catalyst surface sites limit photodegradation. A poly(vinylidene fluoride) (PVDF) nanofiber composite membrane (NCM) with immobilized visible-light-responsive g-C3N4/Bi2MoO6 (BMCN) were developed. Photodegradation of steroid hormones with the PVDF-BMCN NCM was investigated with varying catalyst properties, operating conditions, and relevant solution chemistry under solar irradiation. Increasing CN ratio (0-65 %) enhanced estradiol (E2) degradation from 20 ± 10 to 75 ± 7 % due to improved sunlight utilization and photon lifetime. PVDF nanofibers reduced self-aggregation of catalysts. Hydraulic residence time and light intensity enhanced the photodegradation. With the increasing pH value, the E2 removal decreased from 84 ± 4 to 67 ± 7 % owing to electrical repulsion and thus reduced adsorption between catalysts and E2. A removal of 96 % can be attained at environmentally relevant feed concentration (100 ng.L-1) with a flux of 60 L.m-2.h-1, irradiance of 100 mW.cm-2, and 1 mg.cm-2 BMCN65 loading. This confirmed that heterojunction photocatalysts can enhance micropollutants degradation in PMRs.

Development of inorganic and mixed matrix membranes for application in toxic dyes-contaminated industrial effluents with in-situ treatments

Dyes are the most ubiquitous organic pollutants in industrial effluents. They are highly toxic to both plants and animals; thus, their removal is paramount to the sustainability of ecosystem. However, they have shown resistance to photolysis and various biological, physical, and chemical wastewater remediation processes. Membrane removal technology has been vital for the filtration/separation of the dyes. In comparison to polymeric membranes, inorganic and mixed matrix (MM) membranes have shown potentials to the removal of dyes. The inorganic and MM membranes are particularly effective due to their high porosity, enhanced stability, improved permeability, higher enhanced selectivity and good stability and resistance to harsh chemical and thermal conditions. They have shown prospects in filtration/separation, adsorption, and catalytic degradation of the dyes. This review highlighted the advantages of the inorganic and MM membranes for the various removal techniques for the treatments of the dyes. Methods for the membranes production have been reviewed. Their application for the filtration/separation and adsorption have been critically analyzed. Their application as support for advanced oxidation processes such as persulfate, photo-Fenton and photocatalytic degradations have been highlighted. The mechanisms underscoring the efficiency of the processes have been cited. Lastly, comments were given on the prospects and challenges of both inorganic and MM membranes towards removal of the dyes from industrial effluents.

Influence of organic matter on the photocatalytic degradation of steroid hormones by TiO2-coated polyethersulfone microfiltration membrane

Water treatment in photocatalytic membrane reactors (PMR) holds great promise for removing micropollutants from aquatic environments. Organic matter (OM) that is present in any water matrix may significantly interfere with the degradation of steroid hormone (SH) micropollutants in PMRs. In this study, the interference of various OM types, humic acid (HA), Australian natural organic matter (AUS), worm farm extract (WF), tannic acid (TA), and gallic acid (GA) with the SH degradation at its environmentally relevant concentration (100 ng/L) in a flow-through PMR equipped with a polyethersulphone-titanium dioxide (PES-TiO2) membrane operated under UV light (365 nm) was investigated. Results of this study showed that OM effects are complex and depend on OM type and concentration. The removal of β-estradiol (E2) was enhanced by HA at its levels below 5 mgC/L while the enhancement was abated at higher HA concentrations. The E2 removal was inhibited by TA, and GA, while no significant interference observed for AUS, and WF. The data demonstrated diverse roles of OM that acts in PMRs as a light screening agent, a photoreactive species scavenger, an adsorption alteration trigger, and a photosensitizer. The time-resolved fluorescence measurement showed that HA, acting as a photosensitizer, promoted the sensitization of TiO2 by absorbing light energy and transferring energy/electron to the TiO2 substrate. This pathway dominated the mechanism of the enhanced E2 degradation by HA. The favorable effect of HA was augmented as increasing the light intensity from 0.5 to 10 mW/cm2 and was weakened at higher light intensities due to the increased scavenging reactions and the limited amount of HA. This work clarifies the underlying mechanism of the OM interference on photocatalytic degradation of E2 by the PES-TiO2 PMR.

Enhanced photocatalytic degradation of amoxicillin using a spinning disc photocatalytic reactor (SDPR) with a novel Fe3O4@void@CuO/ZnO yolk-shell thin film nanostructure

Antibiotics are resistant compounds with low biological degradation that generally cannot be removed by conventional wastewater treatment processes. The use of yolk-shell nanostructures in spinning disc photocatalytic reactor (SDPR) enhances the removal efficiency due to their high surface-to-volume ratio and increased interaction between catalyst particles and reactants. The purpose of this study is to investigate the SDPR equipped to Fe3O4@void@CuO/ZnO yolk-shell thin film nanostructure (FCZ YS) in the presence of visible light illumination in the photocatalytic degradation of amoxicillin (AMX) from aqueous solutions. Stober, co-precipitation, and self-transformation methods were used for the synthesis of FCZ YS thin film nanostructure and the physical and chemical characteristics of the catalyst were analyzed by XRD, VSM,, EDX, FESEM, TEM, AFM, BET, contact angle (CA), and DRS. Then, the effect of different parameters including pH (3-11), initial concentration of AMX (10-50 mg/L), flow rate (10-25 mL/s) and rotational speed (100-400 rpm) at different times in the photocatalytic degradation of AMX were studied. The obtained results indicated that the highest degradation efficiency of 97.6% and constant reaction rate of AMX were obtained under LED visible light illumination and optimal conditions of pH = 5, initial AMX concentration of 30 mg/L, solution flow rate of 15 mL/s, rotational speed of 300 rpm and illumination time of 80 min. The durability and reusability of the nanostructure were tested, that after 5 runs had a suitable degradation rate. Considering the appropriate efficiency of amoxicillin degradation by FCZ YS nanostructure, the use of Fe3O4@void@CuO/ZnO thin film in SDPR is suggested in water and wastewater treatment processes.

Atmospheric-pressure atomic layer deposition: recent applications and new emerging applications in high-porosity/3D materials

Atomic layer deposition (ALD) is a widely recognized technique for depositing ultrathin conformal films with excellent thickness control at Ångström or (sub)monolayer level. Atmospheric-pressure ALD is an upcoming ALD process with a potentially lower ownership cost of the reactor. In this review, we provide a comprehensive overview of the recent applications and development of ALD approaches emphasizing those based on operation at atmospheric pressure. Each application determines its own specific reactor design. Spatial ALD (s-ALD) has been recently introduced for the commercial production of large-area 2D displays, the surface passivation and encapsulation of solar cells and organic light-emitting diode (OLED) displays. Atmospheric temporal ALD (t-ALD) has opened up new emerging applications such as high-porosity particle coatings, functionalization of capillary columns for gas chromatography, and membrane modification in water treatment and gas purification. The challenges and opportunities for highly conformal coating on porous substrates by atmospheric ALD have been identified. We discuss in particular the pros and cons of both s-ALD and t-ALD in combination with their reactor designs in relation to the coating of 3D and high-porosity materials.

An Overview of Photocatalytic Membrane Degradation Development

Environmental pollution has become a worldwide issue. Rapid industrial and agricultural practices have increased organic contaminants in water supplies. Hence, many strategies have been developed to address this concern. In order to supply clean water for various applications, high-performance treatment technology is required to effectively remove organic and inorganic contaminants. Utilizing photocatalytic membrane reactors (PMRs) has shown promise as a viable alternative process in the water and wastewater industry due to its efficiency, low cost, simplicity, and low environmental impact. PMRs are commonly categorized into two main categories: those with the photocatalyst suspended in solution and those with the photocatalyst immobilized in/on a membrane. Herein, the working and fouling mechanisms in PMRs membranes are investigated; the interplay of fouling and photocatalytic activity and the development of fouling prevention strategies are elucidated; and the significance of photocatalysis in membrane fouling mechanisms such as pore plugging and cake layering is thoroughly explored.

Performance of TiO2-Based Tubular Membranes in the Photocatalytic Degradation of Organic Compounds

This work presents the photocatalytic degradation of organic pollutants in water with TiO₂ and TiO₂/Ag membranes prepared by immobilising photocatalysts on ceramic porous tubular supports. The permeation capacity of TiO₂ and TiO₂/Ag membranes was checked before the photocatalytic application, showing high water fluxes (≈758 and 690 L m^-2 h^-1 bar^-1, respectively) and <2% rejection against the model pollutants sodium dodecylbenzene sulfonate (DBS) and dichloroacetic acid (DCA). When the membranes were submerged in the aqueous solutions and irradiated with UV-A LEDs, the photocatalytic performance factors for the degradation of DCA were similar to those obtained with suspended TiO₂ particles (1.1-fold and 1.2-fold increase, respectively). However, when the aqueous solution permeated through the pores of the photocatalytic membrane, the performance factors and kinetics were two-fold higher than for the submerged membranes, mostly due to the enhanced contact between the pollutants and the membranes photocatalytic sites where reactive species were generated. These results confirm the advantages of working in a flow-through mode with submerged photocatalytic membranes for the treatment of water polluted with persistent organic molecules, thanks to the reduction in the mass transfer limitations.

Poly(vinylidene fluoride) membrane with immobilized TiO2 for degradation of steroid hormone micropollutants in a photocatalytic membrane reactor

The lack of effective technologies to remove steroid hormones (SHs) from aquatic systems is a critical issue for both environment and public health. The performance of a flow-through photocatalytic membrane reactor (PMR) with TiO₂ immobilized on a photostable poly(vinylidene fluoride) membrane (PVDF-TiO₂) was evaluated in the context of SHs degradation at concentrations from 0.05 to 1000 µg/L under UV exposure (365 nm). A comprehensive investigation into the membrane preparation approach, including varying the surface Ti content and distribution, and membrane pore size, was conducted to gain insights on the rate-limiting steps for the SHs degradation. Increasing surface Ti content from 4 % to 6.5 % enhanced the 17β-estradiol (E2) degradation from 46 ± 12-81 ± 6 %. Apparent degradation kinetics were independent of both TiO₂ homogeneity and membrane pore size (0.1-0.45 µm). With optimized conditions, E2 removal was higher than 96 % at environmentally relevant feed concentration (100 ng/L), a flux of 60 L/m²h, 25 mW/cm², and 6.5 % Ti. These results indicated that the E2 degradation on the PVDF-TiO₂ membrane was limited by the catalyst content and light penetration depth. Further exploration of novel TiO₂ immobilization approach that can offer a larger catalyst content and light penetration is required to improve the micropollutant removal efficiency in PMR.

Rapid Probing of Self-Cleaning Activity on Polyester Coated by Titania-Natural Silica Nanocomposite Using Digital Image-Based Colorimetry

Titania-silica nanocomposites (TiO₂-SiO₂) show outstanding performance and is very well applied in photocatalysis. In this research, SiO₂ extracted from Bengkulu beach sand will be used as a supporting material of the TiO₂ photocatalyst for application to polyester fabrics. TiO₂-SiO₂ nanocomposite photocatalysts were synthesized using the sonochemical method. The coating of the TiO₂-SiO₂ material on polyester was carried out using the sol-gel-assisted sonochemistry method. The method of determining self-cleaning activity uses a digital image-based colorimetric (DIC) method, which is much simpler than using an analytical instrument. The scanning electron microscopy-energy dispersive X-ray spectroscopy results showed that the sample particles adhered to the fabric surface and the best particle distribution was shown in pure SiO₂ and 1:0.5 TiO₂-SiO₂ nanocomposites. Analysis of Fourier-transform infrared (FTIR) spectroscopy proved the presence of Ti-O and Si-O bonds as well as the typical spectrum of polyester, which indicated that the fabric had been successfully coated with nanocomposite particles. The analysis of the contact angle of the liquid on the polyester surface showed a significant change in the properties of the TiO₂ and SiO₂ pure coated fabrics, but changes occur only slightly in the other samples. Self-cleaning activity against the degradation of methylene blue dye has been successfully carried out using DIC measurement. The test results showed that the best self-cleaning activity was shown by TiO₂-SiO₂ nanocomposite with a ratio of 1:0.5 with the degradation ratio reaching 96.8%. Furthermore, the self-cleaning property remains after the washing process, which shows excellent washing resistance.

Photodegradation of Methylene Blue Using Carbon-Doped ZnSn(OH)6 Composite Coated on Membrane

The dye contamination of water is a global concern in the environment. In this study, the photocatalytic technology and membrane module were combined to improve the surface distribution of the active species of the catalyst for better degradation of the methylene blue (MB) dye under visible light. ZnSn(OH)6 was chosen due to carbon’s complex metal oxide doped to facilitate the application under visible light. The numerous characterizations were analyzed in the composites to verify the consistency of the optimum degradation of MB over the catalyst coated on the membrane. During the preparation of the ZnSn(OH)6 composite, the results confirmed that different reaction times and amounts of sodium hydroxide significantly affected the pollutant’s degradation. The carbon-doped composite denoted the largest surface area and increased the catalyst’s reactive sites on the membrane. The photocatalytic activity test showed that 1% carbon doped on ZnSn(OH)6 prepared at 160°C by hydrothermal method coated on the membrane had the optimal degradation of 89.74% of MB. This study contributes to the ongoing study and development of photocatalytic membranes for the photodegradation of wastewater treatment.

Physicochemical and Photocatalytic Properties of 3D-Printed TiO2/Chitin/Cellulose Composite with Ordered Porous Structures

In this study, we printed three-dimensional (3D) titanium dioxide (TiO₂)/chitin/cellulose composite photocatalysts with ordered interconnected porous structures. Chitin microparticles were mixed with cellulose in the N-methylmorpholine-N-oxide (NMMO) solution to prepare the printing "ink". TiO₂ nanoparticles were embedded on the chitin/cellulose composite in the NMMO removal process by water before the freeze-drying process to build the 3D cellulosic photocatalysts with well-defined porous structures. The 3D-printed TiO₂/chitin/cellulose composites were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and Energy Disperse Spectroscopy (EDS). The XRD and FTIR analyses showed that chitin had an interference effect on the crystal regeneration of cellulose and resulted in a large amount of amorphous phase. The SEM images show that the printed cellulosic strands had a hollow structure, and the EDS analysis showed that TiO₂ nanoparticles were embedded on the chitin/cellulose composite surfaces. In the photocatalytic degradation process of methylene blue (MB) dye in an aqueous solution, the TiO₂/chitin/cellulose 3D composite photocatalysts demonstrated efficient MB degradation activities with excellent reusability and stability, in which the chitin content performed the function of adjusting the MB degradation efficiency.

Silicon carbide catalytic ceramic membranes with nano-wire structure for enhanced anti-fouling performance

Membrane fouling is a critical challenge for current ceramic membranes, which suffer from low flux and insufficient removal. Development of self-cleaning catalytic ceramic membranes is promising to address this challenge. Herein, we design heterogeneous silicon carbide ceramic membranes featuring a novel structure of g-C₃N₄-decorated β-SiC nano-wire catalytic functional layer, which enables enhanced anti-fouling self-cleaning performance. At chemical harsh (alkaline or especially acidic) conditions, the nano-wire membrane exhibits catalysis-enhanced removal performance for organic contaminants. Unlike conventional particle-packing membrane structure, such a nano-wire network membrane structure has not only high porosity (56.1%), but exceptional water permeance (110 L·m^-2·h^-1·bar^-1) and removal (100%) of organic substance under simulated sunlight, outperforming state-of-the-art organic membranes and ceramic membranes. Superoxide radical (∙O₂^-) was experimentally confirmed to be major reactive species responsible for self-cleaning function. We also propose a catalytic mechanism model with radical formation pathway, enabled by the as-formed g-C₃N₄@β-SiC heterojunction structure with reduced electron-hole recombination. This work would provide new insights into not only rational design of next-generation ceramic membranes with self-cleaning function but also more applications of efficient treatment of refractory wastewaters containing degradable organic substances by using such membranes.

WO3/Ag/ZnO S-scheme heterostructure thin film spinning disc photoreactor for intensified photodegradation of cephalexin antibiotic

The presence of antibiotics in wastes and drinking water has led to serious environmental and health concerns, further necessitating the development of an advanced sustainable strategy to eliminate antibiotics from aquatic media. In this context, the present research reports the successful fabrication of a spinning disc photoreactor (SDPR) supported ZnO/Ag/WO₃ S-scheme visible-light-driven thin-film photocatalyst to study the degradation of cephalexin (CPX) as a target pollutant under blue light irradiation. The optical, electrochemical and physicochemical characterization of the as-prepared thin-film samples were carried out by XRD, top-view FE-SEM, EDS-mapping, UV-Vis-DRS, contact angle, EIS, transient photocurrent, mott Schottky and AFM techniques. The rod shape morphology of the samples with moderate surface roughness, desirable hydrophobicity, low bandgap and remarkable band structure alignment confirmed the applicability of as-prepared thin-film with an average photon flux of 1.94 × 10^-4-8.61 × 10^-5 E's m^-2 s^-1. The use of a rotating catalytic disc impressively declined the photon propagation distance, decremented the probability of light absorption by the solution, and intensified the mass transfer rate. The maximum throughputs of 98.8% efficiencies for CPX degradation were achieved at a rotational speed of 180 rpm, the solution flow rate of 1.0 L min^-1, the light intensity of 11 mW cm^-2, and initial CPX concentration of 40 mg L^-1, illumination time of 80 min, and pH of 6. Damkohler number (Da) value was found to be 1.23 × 10^-2 at the optimum conditions, indicating the negligibility of the external mass transfer resistance in the SDPR. The photocatalytic mechanism was elucidated for finding the most operative radical species, suggesting the crucial role of ·O₂^- in photodegradation of CPX and a drastic improvement of the charge separation by S-scheme heterostructure and facilitation by Ag mediator. Findings indicated that the developed reusable and robust SDPR benefited from an s-scheme photocatalyst can be a promising technology for degradation of the organic compounds.

Electrified ceramic membrane actuates non-radical mediated peroxymonosulfate activation for highly efficient water decontamination

Electrified ceramic membranes (ECMs) achieve high water decontamination efficiency mainly through implementing in situ radical-mediated oxidation in membrane filtration, whereas ECMs leveraging non-radical pathways are rarely explored. Herein, we demonstrated a Janus ECM realizing ultra-efficient micropollutant (MP) removal via electro-activating peroxymonosulfate (PMS) in a fast, flow-through single-pass electro-filtration. The Janus ECM features two separate palladium (Pd) functionalized electrocatalytic reaction zones engineered on its two sides. We confirmed that the PMS/electro-filtration system induced non-radical pathways for MP degradation, including singlet oxygenation and mediating direct electron transfer (DET) from MP to PMS. Under the design of the ECM featuring dual electrocatalytic reaction zones in the ceramic membrane intrapores, the Janus ECM showed over one-fold increase in micropollutant removal rate as 94.5% and lower electric energy consumption as 1.78 Wh g^-1 MP in the PMS electro-activation process, as compared with the conventional ECM assembly implementing only half-cell reaction. This finding manifested the Janus ECM configuration advantage for maximizing the PMS electro-activation efficiency via singlet oxygenation intensification and direct usage of cathode for DET mediation. The Janus ECM boosted the PMS electro-activation and water decontamination efficiency by enhancing the convective mass transfer and the spatial confinement effect. Our work demonstrated a high-efficiency PMS electro-activation method based on electro-filtration and maximized the non-radical mediated PMS oxidation for MP removal, expanding the ECM filtration strategies for water decontamination.

Application of visible light active photocatalysis for water contaminants: A review

Organic water pollutants are ubiquitous in the natural environment arising from domestic products as well as current and legacy industrial processes. Many of these organic water pollutants are recalcitrant and only partially degraded using conventional water and wastewater treatment processes. In recent decades, visible light active photocatalyst has gained attention as a non-conventional alternative for the removal of organic pollutants during water treatment, including industrial wastewater and drinking water treatment. This paper reviews the current state of research on the use of visible light active photocatalysts, their modified methods, efficacy, and pilot-scale applications for the degradation of organic pollutants in water supplies and waste streams. Initially, the general mechanism of the visible light active photocatalyst is evaluated, followed by an overview of the major synthesis techniques. Because few of these photocatalysts are commercialized, particular attention was given to summarizing the different types of visible light active photocatalysts developed to the pilot-scale stage for practical application and commercialization. The organic pollutant degradation ability of these visible light active photocatalysts was found to be considerable and in many cases comparable with existing and commercially available advanced oxidation processes. Finally, this review concludes with a summary of current achievements and challenges as well as possible directions for further research. PRACTITIONER POINTS: Visible light active photocatalysis is a promising advanced oxidation process (AOP) for the reduction of organic water pollutants. Various mechanisms of photocatalysis using visible light active materials are identified and discussed. Many recent photocatalysts are synthesized from renewable materials that are more sustainable for applications in the 21st century. Only a small number of pilot-scale applications exist and these are outlined in this review.

Ag/AgBr/AgVO3 Photocatalyst-Embedded Polyacrylonitrile/Polyamide/Chitosan Nanofiltration Membrane for Integrated Filtration and Degradation of RhB

A nanofiltration (NF) membrane containing a NaOH-treated electrospun polyacrylonitrile (HPAN) substrate, an interfacial polymerization (IP) polyamide (PA) layer, a chitosan (CS) coating layer, and an Ag/AgBr/AgVO₃ photocatalyst loading layer was prepared. The structural evolution of the membranes was investigated, and their performance was estimated in accordance with the water flux and rejection rate. A probable mechanism for the photocatalytic activity of Ag/AgBr/AgVO₃ was proposed. The loading of the Ag/AgBr/AgVO₃ heterojunction on the HPAN/PA/CS NF membrane endowed the membrane with excellent self-cleaning properties owing to the photolytic degradation of the dye. The filtration and degradation processes of the Ag/AgBr/AgVO₃-loaded membrane constantly promoted each other, and the treatment efficiency achieved with the integrated (filtration + degradation) process was superior to those obtained with the filtration and degradation processes alone. The Ag/AgBr/AgVO₃-NF membrane exhibited excellent recyclability and stability when subjected to five integrated filtration-degradation processes. In addition, the Ag/AgBr/AgVO₃-NF membrane exhibited an elastic modulus of 65.75 MPa and a toughness of 38.9 kJ/m³ along with a good disinfection effect on Escherichia coli in visible light. The as-prepared photocatalyst-loaded NF membrane with excellent antifouling performance, antimicrobial activity, high strength, and recyclability showed potential for continuous water purification operation.

Photocatalytic degradation of steroid hormone micropollutants by TiO2-coated polyethersulfone membranes in a continuous flow-through process

Micropollutants in the aquatic environment pose a high risk to both environmental and human health. The photocatalytic degradation of steroid hormones in a flow-through photocatalytic membrane reactor under UV light (365 nm) at environmentally relevant concentrations (50 ng l^-1 to 1 mg l^-1) was examined using a polyethersulfone-titanium dioxide (PES-TiO₂) membrane. The TiO₂ nanoparticles (10-30 nm) were immobilized both on the surface and in the nanopores (220 nm) of the membrane. Water quality and operational parameters were evaluated to elucidate the limiting factors in the degradation of steroid hormones. Flow through the photocatalytic membrane increased contact between the micropollutants and ·OH in the pores. Notably, 80% of both oestradiol and oestrone was removed from a 200 ng l^-1 feed (at 25 mW cm^-2 and 300 l m^-2 h^-1). Progesterone and testosterone removal was lower at 44% and 33%, respectively. Increasing the oestradiol concentration to 1 mg l^-1 resulted in 20% removal, whereas with a 100 ng l^-1 solution, a maximum removal of 94% was achieved at 44 mW cm^-2 and 60 l m^-2 h^-1. The effectiveness of the relatively well-known PES-TiO₂ membrane for micropollutant removal has been demonstrated; this effectiveness is due to the nanoscale size of the membrane, which provides a high surface area and facilitates close contact of the radicals with the very small (0.8 nm) micropollutant at an extremely low, environmentally relevant concentration (100 ng l^-1).

Photocatalytic membranes: a new perspective for persistent organic pollutants removal

The presence of conventional and emerging pollutants infiltrating into our water bodies is a course of concern as they have seriously threatened water security. Established techniques such as photocatalysis and membrane technology have proven to be promising in removing various persistent organic pollutants (POP) from wastewaters. The emergence of hybrid photocatalytic membrane which incorporates both photocatalysis and membrane technology has shown greater potential in treating POP laden wastewater based on their synergistic effects. This article provides an in-depth review on the roles of both photocatalysis and membrane technology in hybrid photocatalytic membranes for the treatment of POP containing wastewaters. A concise introduction on POP's in terms of examples, their origins and their effect on a multitude of organisms are critically reviewed. The fundamentals of photocatalytic mechanism, current directions in photocatalyst design and their employment to treat POP's are also discussed. Finally, the challenges and future direction in this field are presented.

Supported TiO2 in Ceramic Materials for the Photocatalytic Degradation of Contaminants of Emerging Concern in Liquid Effluents: A Review

The application of TiO₂ as a slurry catalyst for the degradation of contaminants of emerging concern (CEC) in liquid effluents has some drawbacks due to the difficulties in the catalyst reutilization. Thus, sophisticated and expensive separation methods are required after the reaction step. Alternatively, several types of materials have been used to support powder catalysts, so that fixed or fluidized bed reactors may be used. In this context, the objective of this work is to systematize and analyze the results of research inherent to the application of ceramic materials as support of TiO₂ in the photocatalytic CEC removal from liquid effluents. Firstly, an overview is given about the treatment processes able to degrade CEC. In particular, the photocatalysts supported in ceramic materials are analyzed, namely the immobilization techniques applied to support TiO₂ in these materials. Finally, a critical review of the literature dedicated to photocatalysis with supported TiO₂ is presented, where the performance of the catalyst is considered as well as the main drivers and barriers for implementing this process. A focal point in the future is to investigate the possibility of depurating effluents and promote water reuse in safe conditions, and the supported TiO₂ in ceramic materials may play a role in this scope.

Recent developments in porous ceramic membranes for wastewater treatment and desalination: A review

The development of membrane technology has proved vital in providing a sustainable and affordable supply of clean water to address the ever-increasing demand. Though liquid separation applications have been still dominated by polymeric membranes, porous ceramic membranes have gained a commercial foothold in microfiltration (MF) and ultrafiltration (UF) applications due to their hydrophilic nature, lower fouling, ease of cleaning, reliable performance, robust performance with harsh feeds, relative insensitivity to temperature and pH, and stable long-term flux. The enrichment of research and development on porous ceramic membranes extends its focus into advanced membrane separation technologies. The latest emerging nanofiltration (NF) and membrane distillation (MD) applications have witnessed special interests in constructing porous membrane with hydrophilic/functional/hydrophobic properties. However, NF and MD are relatively new, and many shortcomings must be addressed to compete with their polymeric counterparts. For the last three years (2018-2020), state-of-the-art literature on porous ceramic membranes has been collected and critically reviewed. This review highlights the efficiency (permeability, selectivity, and antifouling) of hydrophilic porous ceramic membranes in a wide variety of wastewater treatment applications and hydrophobic porous ceramic membranes in membrane distillation-based desalination applications. A significant focus on pores characteristics, pore sieving phenomenon, nano functionalization, and synergic effect on fouling, the hydrophilic porous ceramic membrane has been discussed. In another part of this review, the role of surface hydrophobicity, water contact angle, liquid entry pressure (LEP), thermal properties, surface micro-roughness, etc., has been discussed for different types of hydrophobic porous ceramic membranes -(a) metal-based, (b) silica-based, (c) other ceramics. Also, this review highlights the potential benefits, drawbacks, and limitations of the porous membrane in applications. Moreover, the prospects are emphasized to overcome the challenges in the field.

Effects of Anodic Aluminum Oxide Substrate Pore Geometry on the Gas-Phase Photocatalytic Activity of ZnO/Al2O3 Composites Prepared by Atomic Layer Deposition

We report on the photocatalytic activity of ZnO layers deposited by atomic layer deposition on a porous anodic aluminum oxide substrate with hexagonal pore symmetry and varied pore dimensions. ZnO/Al2O3 composites were prepared with pore diameters in the range 93–134 nm and interpore distance in the range 185–286 nm, and their photocatalytic activity was measured for gas-phase photocatalytic oxidation of acetaldehyde at varying UV illumination intensities (0.08–3.94 mW cm−2). The results show that substrates with narrower pore diameters (<115 nm, in the case of this study) have a detrimental effect on the photocatalyst performance, despite their higher effective surface. The results are explained on the basis of limited mass transfer inside the porous structure and can be used as a guideline in the purposeful design of photocatalysts with a nanoporous or nanotubular structure.

Photon Upconversion for Photovoltaics and Photocatalysis: A Critical Review

Opportunities for enhancing solar energy harvesting using photon upconversion are reviewed. The increasing prominence of bifacial solar cells is an enabling factor for the implementation of upconversion, however, when the realistic constraints of current best-performing silicon devices are considered, many challenges remain before silicon photovoltaics operating under nonconcentrated sunlight can be enhanced via lanthanide-based upconversion. A photophysical model reveals that >1-2 orders of magnitude increase in the intermediate state lifetime, energy transfer rate, or generation rate would be needed before such solar upconversion could start to become efficient. Methods to increase the generation rate such as the use of cosensitizers to expand the absorption range and the use of plasmonics or photonic structures are reviewed. The opportunities and challenges for these approaches (or combinations thereof) to achieve efficient solar upconversion are discussed. The opportunity for enhancing the performance of technologies such as luminescent solar concentrators by combining upconversion together with micro-optics is also reviewed. Triplet-triplet annihilation-based upconversion is progressing steadily toward being relevant to lower-bandgap solar cells. Looking toward photocatalysis, photophysical modeling indicates that current blue-to-ultraviolet lanthanide upconversion systems are very inefficient. However, hope remains in this direction for organic upconversion enhancing the performance of visible-light-active photocatalysts.

Nanoparticles functionalized ceramic membranes: fabrication, surface modification, and performance

Membrane technologies are used intensively for desalination and wastewater treatment. Water filtration using ceramic membranes exhibited high performance compared with polymeric membranes due to various properties such as high resistance to fouling, permeability, rejection rate, and chemical stability. Recently, the performance of nanocomposite ceramic membranes was improved due to the development in nanotechnology. This article focusses on the development of porous ceramic membranes and nanomaterial functionalized ceramic membranes for water filtration applications. At the beginning, various fabrication methods of ceramic membranes were described, and the effect of surface modification techniques on the membrane intrinsic properties was reviewed. Then, the performance of nanoparticles functionalized ceramic membranes was evaluated in terms of physicochemical properties, rejection rate, and water permeability. This work can help new entrants and established researchers to become familiar with the current challenges and developments of nanoparticle-incorporated ceramic membranes for water filtration applications.

Surface Modification of Catalysts via Atomic Layer Deposition for Pollutants Elimination

In recent years, atomic layer deposition (ALD) is widely used for surface modification of materials to improve the catalytic performance for removing pollutants, e.g., CO, hydrocarbons, heavy metal ions, and organic pollutants, and much progress has been achieved. In this review, we summarize the recent development of ALD applications in environmental remediation from the perspective of surface modification approaches, including conformal coating, uniform particle deposition, and area-selective deposition. Through the ALD conformal coating, the activity of photocatalysts improved. Uniform particle deposition is used to prepare nanostructured catalysts via ALD for removal of air pollutions and dyes. Area-selective deposition is adopted to cover the specific defects on the surface of materials and synthesize bimetallic catalysts to remove CO and other contaminations. In addition, the design strategy of catalysts and shortcomings of current studies are discussed in each section. At last, this review points out some potential research trends and comes up with a few routes to further improve the performance of catalysts via ALD surface modification and deeper investigate the ALD reaction mechanisms.

Comparison of Photocatalytic Membrane Reactor Types for the Degradation of an Organic Molecule by TiO2-Coated PES Membrane

Photocatalytic membrane reactors with different configurations (design, flow modes and light sources) have been widely applied for pollutant removal. A thorough understanding of the contribution of reactor design to performance is required to be able to compare photocatalytic materials. Reactors with different flow designs are implemented for process efficiency comparisons. Several figures-of-merit, namely adapted space-time yield (STY) and photocatalytic space-time yield (PSTY), specific energy consumption (SEC) and degradation rate constants, were used to assess the performance of batch, flow-along and flow-through reactors. A fair comparison of reactor performance, considering throughput together with energy efficiency and photocatalytic activity, was only possible with the modified PSTY. When comparing the three reactors at the example of methylene blue (MB) degradation under LED irradiation, flow-through proved to be the most efficient design. PSTY1/PSTY2 values were approximately 10 times higher than both the batch and flow-along processes. The highest activity of such a reactor is attributed to its unique flow design which allowed the reaction to take place not only on the outer surface of the membrane but also within its pores. The enhancement of the mass transfer when flowing in a narrow space (220 nm in flow-through) contributes to an additional MB removal.

Phase Transformations and Photocatalytic Activity of Nanostructured Y2O3/TiO2-Y2TiO5 Ceramic Such as Doped with Carbon Nanotubes

This work is devoted to the study of phase transition processes in nanostructured ceramics of the Y₂O₃/TiO₂-Y₂TiO₅ type doped with carbon nanotubes as a result of thermal annealing, as well as to the assessment of the prospects of the effect of phase composition on photocatalytic activity. By the method of X-ray phase analysis, it was found that an increase in the annealing temperature leads to the formation of the orthorhombic phase Y₂TiO₅, as well as structural ordering. Based on the obtained UV spectra, the band gap was calculated, which varies from 2.9 eV (initial sample) to 2.1 eV (annealed at a temperature of 1000 °C). During photocatalytic tests, it was established that the synthesized nanostructured ceramics Y₂O₃/TiO₂-Y₂TiO₅ doped CNTs show a fairly good photocatalytic activity in the range of 60–90% decomposition of methyl orange.

Investigation of the reaction kinetics of photocatalytic pollutant degradation under defined conditions with inkjet-printed TiO2 films – from batch to a novel continuous-flow microreactor

Reaction kinetics was studied for photocatalytic pollutant degradation with inkjet-printed TiO₂ in a batch and a continuous-flow microreactor.